KYMV060C4 2 BY 2 MPDP INSTALLATION GUIDE KINGYOO Electronics., LTD

KYMV060C4 2 BY 2 MPDP INSTALLATION GUIDE

KINGYOO Electronics., LTD.

AUG. 2012R&D DiV

Jung Kee Young

Contents

STAND TYPE…………………………………………………………………..

2

1. Safety Precau-tion

…………………………………………………

3

2. Parts List ……………………………………………………………..

4

3. Tools ……………………………………………………………………

4

4. Installing the T STAND ASSY ………………………………

5

5. Installing the MPDP …………………………………………….

8

6. Adjust the MPDP ………………………………………….……

12

7. Cable Connection ………………………………………….……

12

KYMV060C4 MPDP

-1-

* This manual describes the installation case for 2by2 sets.

STAND TYPE

-2-

STAND TYPE

KYMV060C4 MPDP

-3-

1. Safety Precaution

KYMV060C4 MPDP STAND TYPE

-3-

1. Safety Precaution

* Please read and understand this manual fully before installation.* Please hand over this manual to customers after instal-lation and ask to read and keep this manual for future use.※ Please keep all the cautions and warnings for proper use of the product and prevent possible accident of hazard.

KYMV060C4 MPDP STAND TYPE

-4-

2. Part List

KYMV060C4 MPDP STAND TYPE

STAND ASSY 1EA

AL PROFILE 2EA

WALL BRACKET ASSY 2EA

PDP PANEL 4EA

BRACKET JIG 2EA

M6 T BOLT, NUT 16EA

M8 T BOLT, NUT 24EA

3. Tools

* Tools are NOT in-cluded.

10,12mm WRENCH SCREWDRIVER 5mm ALLEN WRENCHGUIDE PIN 8EA

DVI CABLE 4EA POWER CORD 4EA

RS232 CABLE 4EA

LAN CABLE 8EA

-5-

4. Installing the T Stand ASSY

KYMV060C4 MPDP STAND TYPE

1. Insert the AL PROFILE to the T Stand ASSY. 2. Hook the WALL BRACKET ASSY at the bottom row to the AL PROFILE.

* It is convenient to set the center with BLACK LINE on the AL PRO-FILE.

BOTTOMWALL PLATE

-6-

4. Installing the T Stand ASSY

KYMV060C4 MPDP STAND TYPE

3. Assemble the WALL BRACKET ASSY and AL PRO-FILE with the M8 T bolt, Nut.

4. Hook the WALL BRACKET ASSY at the 2nd row to the AL PROFILE.

Assemble the fig-ure Using the 12mm Wrench

-7-

4. Installing the T Stand ASSY

KYMV060C4 MPDP STAND TYPE

5. Assemble the WALL BRACKET ASSY and AL PRO-FILE with the M8 T bolt, Nut.

6. Assemble the Bracket Jig with the M8 T bolt, Nut.

Assemble the fig-ure Using the 12mm Wrench

120mm

-8-

5. Installing the MPDP

KYMV060C4 MPDP STAND TYPE

7. Move the WALL PLATE in each direction. 8. To prevent crash lower PDP and upper PDP, Adjust the bolt.

Lose the bolt to move the WALL PLATE.Fasten the bolt to lock the sliding.

WALL PLATE.

Fasten the bolt to move the Bracket Slider.

WALL PLATE.

-9-

5. Installing the MPDP

KYMV060C4 MPDP STAND TYPE

9. Take the PE-FOAM out of the Carton Box. 10. Lay the PDP on the PE-FOAM. Assemble the GUIDE PIN.

PE-FOAM

PE-FOAM 4EA

PDP

GUIDE PIN

-10-

5. Installing the MPDP

KYMV060C4 MPDP STAND TYPE

12. Assemble the GUIDE PIN. Assemble the PDP at the bottom row to the right

11. Assemble the PDP at the bottom row to the left.

Panel No. : 1Left TOP

Panel No. : 2Right TOP

Panel No. : 3Left BOT-TOM

Panel No. : 4Right BOT-TOM

-11-

5. Installing the MPDP

KYMV060C4 MPDP STAND TYPE

14. Assemble the GUIDE PIN. Assemble the PDP at the 2nd row to the right

13. Assemble the PDP at the 2nd row to the left.

-12-

6. Adjust the MPDP

KYMV060C4 MPDP STAND TYPE

16. Adjust the height of the PDP with the bolt15. Lose the bolt to move the PDP. Push the PDP slowly.

-13-

6. Adjust the MPDP

KYMV060C4 MPDP STAND TYPE

18. After adjust the PDP of 2nd row, Fasten the bolt to lock the sliding.

17. Repeat the work indicated in Step No. 16 to ad-just the PDP.

-14-

6. Adjust the MPDP

KYMV060C4 MPDP STAND TYPE

20. Push the AL PROFILE from behind to move the product.

19. If you need to move or replace the product, Don’t push the PDP.

※ If users push the PDP After as-sembling, it may Cause safety problem.

-15-

7. Cable Connection

KYMV060C4 MPDP STAND TYPE

22..21. .