View
220
Download
0
Category
Preview:
Citation preview
OBJETIVO Al completar esta práctica de laboratorio, tu podrás conectar una red de acuerdo con el Diagrama de la topología también en esta práctica aprenderemos a configurar una Nueva forma con tipo de comandos aprenderás de una forma diferente y que la configuración no es la misma ya que para conocer perfectamente la topología de la red los algoritmos de estado de enlace utilizan diferentes elemento de estado enlace aprenderemos formas mas especificas de cómo poder hacer dichas configuraciones además aprenderemos
como se puede configurar una red con el ospf ya que maneja una forma diferente al eigrp es un poco mas compleja por los tipo de requerimientos que este necesita pues después de esto manos a la obra y empieza la practica OSPF, ha sido pensado para el entorno de Internet y su pila de protocolos TCP/IP, como un protocolo de routing interno, es decir, que distribuye información entre routers que pertenecen al mismo Sistema Autónomo.
Des puedes de haber configurado el procedimiento fue un poco complicado pero fue algo muy práctico ya que me costó un poco de trabajo fue algo muy importante por me pode dar cuenta que el ospf no solo se configura con el nertwork además de eso lleva la wilcard que especifica q mascara es el ospf también al momento de configurarlo cuenta con un sistema autónomo que le sirve para poder ingresarlo dentro de l router sin dicho Ide no es posible configurar el ospf que en este caso su ide fue el 1 pero no siempre será hací ya que el ide pude variar además también fue configurada con el la interface loopback que es una dirección especial que los hosts utilizan para dirigir el tráfico hacia ellos mismos
PRACTICA 3PARCIALRuprer 1
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R1
R1(config)#interface s0/0/0
R1(config-if)#ip add 192.168.10.1 255.255.255.252
R1(config-if)#clock rate 64000
R1(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
R1(config-if)#exit
R1(config)#interface s0/0/1
R1(config-if)#ip add 192.168.10.5 255.255.255.252
R1(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
R1(config-if)#exit
R1(config)#interface fa0/0
R1(config-if)#ip add 172.16.1.17 255.255.255.240
R1(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R1(config-if)#exit
R1(config)#router ospf 1
R1(config-router)#network 192.16.1.16 0.0.0.15 area 0
R1(config-router)#network 192.168.10.0 0.0.0.3 area 0
R1(config-router)#network 192.168.10.4 0.0.0.3 area 0
R1(config-router)#exit
R1(config)#enable secret class
R1(config)#enable password cisco
R1(config)#line console 0
R1(config-line)#password cisco
R1(config-line)#exit
R1(config)#line vty 04
R1(config-line)#password cisco
R1(config-line)#login
R1(config-line)#exit
R1(config)# interface loopback 0
%LINK-5-CHANGED: Interface Loopback0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up
R1(config-if)# ip add 10.1.1.1 255.255.255.255
R1(config-if)#
RUPTER 2Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R2
R2(config)#interface s0/0/0
R2(config-if)#ip add 192.168.10.2 255.255.255.252
R2(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
R2(config-if)#exit
R2(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
R2(config)#interface s0/0/1
R2(config-if)#ip add 192.168.10.9 255.255.255.252
R2(config-if)#clock rate 64000
R2(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
R2(config-if)#exit
R2(config)#interface fa0/0
R2(config-if)#ip add 192.10.10.1 255.255.255.0
R2(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R2(config-if)#exit
R2(config)#router ospf 1
R2(config-router)#exit
R2(config)#interface fa0/0
R2(config-if)#ip add 10.10.10.1 255.255.255.0
R2(config-if)#no shutdown
R2(config-if)#exit
R2(config)#router ospf 1
R2(config-router)#network 10.10.10.0 0.0.0.255 area 0
R2(config-router)#network 192.168.10.8 0.0.0.3 area 0
R2(config-router)#network 192.168.10.0 0.0.0.3 area 0
R2(config-router)#
00:58:11: %OSPF-5-ADJCHG: Process 1, Nbr 192.168.10.5 on Serial0/0/0 from LOADING to FULL, Loading Done
R2(config-router)#exit
R2(config)#enable secret class
R2(config)#enable password cisco
R2(config)#line console 0
R2(config-line)#password cisco
R2(config-line)#exit
R2(config)#line vty 04
R2(config-line)#password cisco
R2(config-line)#login
R2(config-line)#exit
R2(config)#interface loopback 0
%LINK-5-CHANGED: Interface Loopback0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up
R2(config-if)#exit
R2(config)#ip address 10.2.2.2 255.255.255.255
R2(config)#interface loopback 0
R2(config-if)#ip address 10.2.2.2 255.255.255.255
R2(config-if)#exit
ROUTER 3Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R3
R3(config)#interface s0/0/0
R3(config-if)#ip add 192.168.10.6 255.255.255.252
R3(config-if)#clock rate 64000
R3(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
R3(config-if)#exit
R3(config)#inte
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
R3(config)#interface s0/0/1
R3(config-if)#ip add 192.168.10.10 255.255.255.252
R3(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up
R3(config-if)#exit
R3(config)#no shutdown
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up
R3(config)#exit
R3#
%SYS-5-CONFIG_I: Configured from console by console
R3#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
R3(config)#interface fa0/0
R3(config-if)#ip add 172.16.1.33 255.255.255.248
R3(config-if)#exit
R3(config)#interface fa0/0
R3(config-if)#ip add 172.16.1.33 255.255.255.248
R3(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R3(config-if)#exit
R3(config)#router ospf 1
R3(config-router)#network 172.16.1.32 0.0.0.7 area 0
R3(config-router)#network 192.168.10.4 0.0.0.3 area 0
R3(config-router)#network 192.168.10.4 0.0.0.3 area 0
01:19:27: %OSPF-5-ADJCHG: Process 1, Nbr 192.168.10.5 on Serial0/0/0 from LOADING to FULL, Loading Done
R3(config-router)#network 192.168.10.8 0.0.0.3 area 0
R3(config-router)#exit
R3(config)#
01:19:59: %OSPF-5-ADJCHG: Process 1, Nbr 192.168.10.9 on Serial0/0/1 from LOADING to FULL, Loading Done
R3(config)#enable secret class
R3(config)#enable password cisco
R3(config)#line console 0
R3(config-line)#password cisco
R3(config-line)#line vty 04
R3(config-line)#exit
R3(config)#line vty 04
R3(config-line)#password cisco
R3(config-line)#login
R3(config-line)#exit
R3(config)#interface loopback 0
%LINK-5-CHANGED: Interface Loopback0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up
R3(config-if)#ip address 10.3.3.3 255.255.255.255
R3(config-if)#exit
PRACTICA DOS
Al completar esta práctica de laboratorio, usted podrá conectar una red de acuerdo con el Diagrama de topología. Eliminar la configuración de inicio y recargar un router para volver al estado predeterminado
Realizar tareas de configuración básicas en un router configurar y activar interfaces Configurar el enrutamiento OSPF en todos los routers configurar los ID del router OSPF Verificar el enrutamiento OSPF por medio de los comandos.
Es ta practica te servirá para poder realizar una configuración fácil sencilla y rápida la configuración es eficaz y usas comandos que anteriormente ya utilizaste.
En esta topología hay tres routers que comparten una red Ethernet de accesos múltiples, la red 192.168.1.0/24. Cada router se configurará con una dirección IP en la interfaz Fast Ethernet y una dirección de loopback para el ID del router y son configurados con la misma red pero diferentes números de de Ip..
Router 1mexico>enable
mexico#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
mexico(config)#hostname R1
R1(config)# interface fa0/0
R1(config-if)#ip add 192.168.1.1 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#exit
R1(config)#enable secret class
R1(config)#enable password cisco
R1(config)#line console 0
R1(config-line)#password cisco
R1(config-line)#exit
R1(config)#line vty 04
R1(config-line)#password cisco
R1(config-line)#login
R1(config-line)#exit
R1(config)#interface loopback 1
%LINK-5-CHANGED: Interface Loopback1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up
R1(config-if)#ip add 192.168.31.11 255.255.255.255
R1(config-if)#exit
R1(config)#
ROUTER 2veracruz>enable
veracruz#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
veracruz(config)#hostname R2
R2(config)# interface fa0/0
R2(config-if)# ip add 192.168.1.2 255.255.255.0
R2(config-if)# no shutdown
R2(config-if)exit
R2(config)# enable secret class
R2(config)#enable password cisco
R2(config)#line console 0
R2(config-line)#password cisco
R2(config-line)#exit
R2(config)#line vty 04
R2(config-line)#password cisco
R2(config-line)#login
R2(config-line)#exit
R2(config)#interface loopback 1
%LINK-5-CHANGED: Interface Loopback1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up
R2(config-if)#ip add 192.168.31.22 255.255.255.255
R2(config-if)#exit
R2(config)#
ROUTER 3 chicago>enable
chicago#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
chicago(config)#hostname R3
R3(config)#interface fa0/0
R3(config-if)#ip add 192.168.1.3 255.255.255.0
R3(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R3(config-if)#exit
R3(config)#enable secret class
R3(config)#enable password cisco
R3(config)#line console 0
R3(config-line)#password cisco
R3(config-line)#exit
R3(config)#line vty 04
R3(config-line)#password cisco
R3(config-line)#login
R3(config-line)#exit
R3(config)#interface loopback 1
%LINK-5-CHANGED: Interface Loopback1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback1, changed state to up
R3(config-if)#ip add 192.168.31.33 255.255.255.255
R3(config-if)#exit
R3(config)#
Recommended