BTS3900 Configuration Level: internal
2009-7-2 Page17, Total17
The log above indicates that importing is successful. Step6:
edit the MML script Use the UltraEdit tool to edit the exported
file namedBTS3900 adjacent cell above. CommanADD CELL2GNC will be
used to add adjacent cell. Its very to edit the MML script with the
UltraEdit tool in column mode. Take care theBidirectional Adjacent
CellandSingle directional Adjacent Cell! For the theBidirectional
Adjacent Cell, command ADD CELL2GNC should be executed twice to add
adjacent cell in both cell. Step7: execute the MML script in batch
Log in the MML and execute the scriptBTS3900 adjacent cell in
batch.
/ColorImageDict > /JPEG2000ColorACSImageDict >
/JPEG2000ColorImageDict > /AntiAliasGrayImages false
/CropGrayImages true /GrayImageMinResolution 300
/GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true
/GrayImageDownsampleType /Bicubic /GrayImageResolution 300
/GrayImageDepth -1 /GrayImageMinDownsampleDepth 2
/GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true
/GrayImageFilter /DCTEncode /AutoFilterGrayImages true
/GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict >
/GrayImageDict > /JPEG2000GrayACSImageDict >
/JPEG2000GrayImageDict > /AntiAliasMonoImages false
/CropMonoImages true /MonoImageMinResolution 1200
/MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true
/MonoImageDownsampleType /Bicubic /MonoImageResolution 1200
/MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000
/EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode
/MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None
] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false
/PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000
0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true
/PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ]
/PDFXOutputIntentProfile () /PDFXOutputConditionIdentifier ()
/PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped
/False
/Description > /Namespace [ (Adobe) (Common) (1.0) ]
/OtherNamespaces [ > /FormElements false /GenerateStructure true
/IncludeBookmarks false /IncludeHyperlinks false
/IncludeInteractive false /IncludeLayers false /IncludeProfiles
true /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe)
(CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /NA
/PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged
/UntaggedRGBHandling /LeaveUntagged /UseDocumentBleed false
>> ]>> setdistillerparams> setpagedevice
BTS3900 Configuration
Level: internal
BTS3900 Configuration Guideline
Drafted by
Quan Kuifa
Date
JUN.10.2009
Reviewed by
Date
Approved by
Date
Huawei Technologies Co., Ltd.
All rights reserved.
This guide instructs that how to configur BTS3900 in the
BSC6000.also that how to implement BTS swap.All the operations is
based on the LMT and MML.
The content of this guide is as below:
1, Main process of BTS configuration
2, Alarm configuration for BTS
3, Data configuration for BTS swap
1. Main process of BTS configuration
Keep the same configuartion with site Batna CCLT 05503 in the
Batna.
Step1: add site
Step2: add cell
Step3: set attributes
Step4: add FMU and GATM board
(Each BTS3900 is configured with 6 DRFU.1 FMU.1 GATM.1 BBU.)
Add FMU in slot 8 and GATM in slot 17, because the monitor
signal cable of FMU and GATM are connected to MON0 and MON1 of UPEU
separately.which keeps the confiuration same with the practical
installation.
Step5: add RXU Chain
Use the RF cable connection tool to generate the connection. For
the site 05503(S4/4/4) is as below:
Step6: add RXU (RFU)
Principia for RXUs name: PortX_SlotX_PosX.
PortX: Port No. X of GTMU
SlotX: Slot No. X of DRFU
PosX: Position No.X of the DRFU in the chain.
Keep confiuration same with the practical connection.Finally the
RXU chain topo is as below.
Step7: bind logical TRX
From Trx No.0 to Trx No.11
Step8: Set TRX attributes (Send Receive Mode)
Set the Send Receive Mode due to pratical situation. Because
just one ANT port of DRFU is used, the Single Antenna Double
Receiver is chosen.
Step9: Set cell attributes
Almost the configuration process is same with BSC32.
One parameter should be cared, which isPower Type. 20W is chosen
due to the Send Receive Mode.
2. Alarm configuration for BTS3900
The BBU can support 2 RS485 bus and 16 line of on-off alarm
maximally.
There are just 1 UPEU configured in BTS3900 in the packeting
list.
The No. of on-off alarm for UPEU is as below.
The monitor signal of DCDU-01 is connected to No.8 alarm of
EXT-ALM0 of UPEU.
Step1: set site attributes
Step2: set Alarm Shield Flag 2 (Hex)
The 8 bits (from low to high) of alarm sheild flag 2 determines
the No.8-15 on-off alarm. 0 means shield, 1 means non-shield.
The alarm sheild flag 2 is set as 01 to enable the DCDU-01
arlarm.
Step3: set Alarm Voltage Definition
Step4: set external alarm port
Set the external alarm port for the on-off alarm of the UPEU as
below.
Step5: name the external alarm
Click the Alarm Matintenance in the LMT mean
Find the No.5048 alarm.then right-click it.choose as below.
Set the Alarm name.
3. Data configuration for BTS swap
Step1: configure the site with LMT in offline mode
Note: Configure the site on the same slot and port as the site
to be swapped.
Step2: export the site data in offline mode
It will take about 5 minutes to export one site data.
Step3: backup the data of the swapped site in online mode
Note: do this after blocking the site.
The exported result is the format of text as above, which will
be used to edit the adjacent cell for BTS3900 later.
Step4: delete the swapped site in online mode
Step5: import the data in online mode
The log above indicates that importing is successful.
Step6: edit the MML script
Use the UltraEdit tool to edit the exported file namedBTS3900
adjacent cell above.
CommanADD CELL2GNC will be used to add adjacent cell. Its very
to edit the MML script with the UltraEdit tool in column mode.
Take care theBidirectional Adjacent CellandSingle directional
Adjacent Cell! For the theBidirectional Adjacent Cell, command ADD
CELL2GNC should be executed twice to add adjacent cell in both
cell.
Step7: execute the MML script in batch
Log in the MML and execute the scriptBTS3900 adjacent cell in
batch.
2009-7-2
Page1, Total17
![Guide to BTS3900 and BTS3900A SDR and RFU Co-Cabinet Slot Configuration Principles and Internal Cable Connections-20091229-A-V1[1].0](https://img.pdfslide.tips/doc/110x75/55cf98ec550346d0339a7ae9/guide-to-bts3900-and-bts3900a-sdr-and-rfu-co-cabinet-slot-configuration-principles.jpg)
