2
Ch e vr ol e t Si l ve r ado 1999 WWW.WIREMAGIC.COM Wire / Function Colour Location / Descri ption Polarit y  Installation type: Remote start / security / GPS  YES PASSLOCK II SEE NOTES PASSIVE ANTI-THEFT Red Ignition harness + 12 VOLTS Pink Ignition harness + IGNITION White Ignition harness + IGNITION 2 Orange Ignition harness + ACCESSORY Yellow Ignition harness + STARTER See notes* TACH Lt.blue At Body Control Module** + LOCK White At Body Control Module** + UNLOCK Tan & Lt.blue At Body Control Module** - DOORPIN See notes*** FACTORY ARM Lt.green At Body Control Module** - FACTORY DISARM White At switch above brake pedal + BRAKESWITCH Lt.blue**** At light switch harness + PARKLIGHTS Lt.blue At switch on parking brake lever  - HAND BRAKE Black At steering column - HORN Purple/white At switch on top of clutch pedal TYPE 1 CLUTCH SWITCH Dk.blue At window switch in driver's door  REV POL DRIVER WINDOW UP Brown At window switch in driver's door  REV POL DRIVER WINDOW DOWN Lt.blue At window switch in driver's door  REV POL PASSENGER WINDOW UP Tan At window switch in driver's door  REV POL PASSENGER WINDOW DOWN White At light switch harness + HEADLIGHTS Lt.green DKP harness to rear of vehicle + REVERSE LIGHTS Green At light switch harness + DIMMER Dk.green/white***** At VCM in left front engine compartment 4000ppm VSS WIRE Lt.green Ignition switch harness - KEY SENSE NOSHOW01 PLEASE NOTE: This vehicle is equipped with GM's Passlock II passive fuel cut-off system. See the security diagram for bypass information. * The 4300 V6 engine still uses a single coil on the top of the engine, tach wire is WHITE. On the V8 engines, there is a coil for each cylinder, each with a 4 pin plug. Each plug contains a BLACK, BROWN & PINK, as well as a 4th wire which changes color on each coil. This 4th wire can be u sed as your tach reference, set your remote starter for a 1 cylinder signal. You can also use a WHITE at pin- 10 of the 80-pin connector on the PCM at the left front of the engine compartment for a 8 cylinder signal. ** The Body Control Module is loca ted directly below the steering column. Factory security is only available on the LS & LT models. *** The factory alarm can be armed by grounding the driver's doorpin TAN, while locking the doors. **** TAN is driver's door & LT.BLUE is passenger side door. ***** Located at pin-3 on the C4 24-pin plug (4.3L only). Located at pin-50 of C2 80-pin connector for all other engines. Vehicl e note : F r i day, August 09, 2002 Page 1 of 1  Note: The information on this sheet is provided to you on an as is basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. Wiremagic.com Corporation and/or any associated or unassociated individual or corporation who furnishes this document and/or software assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in each and every case is the sole responsibility of the installer performing the work and Wiremagic.com Corporation and/or any associated or unassociated individual or corporation assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly, or in any other way. The information supplied is a guide only. © Copyright 1998-2001 Wiremagic.com Corporation. All rights reserved.

1999 Silverado

Embed Size (px)

Citation preview

 

Chevrolet Silverado 1999 

WWW.WIREMAGIC.COM

Wire/Function Colour Location / Descr iption Polar i ty  

Installation type: Remote start / security / GPS 

YES PASSLOCK II SEE NOTESPASS IVE ANTI-THEFT 

Red Ignition harness +12 VOLTS 

Pink Ignition harness +IGNITION 

White Ignition harness +IGNITION 2 

Orange Ignition harness +ACCESSORY 

Yellow Ignition harness +STARTER 

See notes*TACH 

Lt.blue At Body Control Module** +LOCK 

White At Body Control Module** +UNLOCK 

Tan & Lt.blue At Body Control Module** -DOORPIN 

See notes***FACTORY ARM 

Lt.green At Body Control Module** -FACTORY DISARM 

White At switch above brake pedal +BRAKESWITCH 

Lt.blue**** At light switch harness +PARKLIGHTS 

Lt.blue At switch on parking brake lever   -HAND BRAKE 

Black At steering column -HORN 

Purple/white At switch on top of clutch pedal TYPE 1CLUTCH SWITCH 

Dk.blue At window switch in driver's door   REV POLDRIVER WINDOW UP 

Brown At window switch in driver's door   REV POLDRIVER WINDOW DOWN 

Lt.blue At window switch in driver's door   REV POLPASSENGER WINDOW UP 

Tan At window switch in driver's door   REV POLPASSENGER WINDOW DOWN 

White At light switch harness +HEADLIGHTS 

Lt.green DKP harness to rear of vehicle +REVERSE LIGHTS 

Green At light switch harness +DIMMER 

Dk.green/white***** At VCM in left front engine compartment 4000ppmVSS WIRE 

Lt.green Ignition switch harness -KEY SENSE 

NOSHOW01 

PLEASE NOTE: This vehicle is equipped with GM's Passlock II passive fuel cut-off system. See the security diagram for bypass

information.

* The 4300 V6 engine still uses a single coil on the top of the engine, tach wire is WHITE. On the V8 engines, there is a coil for each

cylinder, each with a 4 pin plug. Each plug contains a BLACK, BROWN & PINK, as well as a 4th wire which changes color on each

coil. This 4th wire can be used as your tach reference, set your remote starter for a 1 cylinder signal. You can also use a WHITE at pin-

10 of the 80-pin connector on the PCM at the left front of the engine compartment for a 8 cylinder signal.

** The Body Control Module is located directly below the steering column. Factory security is only available on the LS & LT models.

*** The factory alarm can be armed by grounding the driver's doorpin TAN, while locking the doors.

**** TAN is driver's door & LT.BLUE is passenger side door.

***** Located at pin-3 on the C4 24-pin plug (4.3L only). Located at pin-50 of C2 80-pin connector for all other engines.

Vehicle note: 

Friday, August 09, 2002 Page 1 of 1  

Note: The information on this sheet is provided to you on an as is basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuitbefore connecting to it. Only a computer safe logic probe or digital multimeter should be used. Wiremagic.com Corporation and/or any associated or unassociated individual or corporation who furnishes this

document and/or software assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in each and every case is the soleresponsibility of the installer performing the work and Wiremagic.com Corporation and/or any associated or unassociated individual or corporation assumes no liability or responsibility whatsoever resultingfrom any type of installation, whether performed properly, improperly, or in any other way. The information supplied is a guide only. © Copyright 1998-2001 Wiremagic.com Corporation. All rights reserved.