3gpp Ts 25.133 v9.0.0 (2009-05)

8/14/2019 3gpp Ts 25.133 v9.0.0 (2009-05)

1/233

3GPP TS 25.133 V9.0.0 (2009-05)Technical Specification

3rd Generation Partnership Project;Technical Specification Group Radio Access Network;

Requirements for support of radio resource management(FDD)

(Release 9)

The present document has been developed within the 3rd Generation Partnership Project (3GPP TM) and may be further elaborated for the purposes of 3GPP.

The present document has not been subject to any approval process by the 3GPPOrganizational Partners and shall not be implemented.This Specification is provided for future development work within 3GPP only. The Organizational Partners accept no liability for any use of thisSpecification.Specifications and reports for implementation of the 3GPP TM system should be obtained via the 3GPP Organizational Partners' Publications Offices.

8/14/2019 3gpp Ts 25.133 v9.0.0 (2009-05)

2/2333GPP

KeywordsUMTS, base station, testing

3GPP

Postal address

3GPP support office address650 Route des Lucioles - Sophia Antipolis

Valbonne - FRANCETel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16

Internethttp://www.3gpp.org

Copyright Notification

No part may be reproduced except as authorized by written permission.The copyright and the foregoing restriction extend to reproduction in all media.

2009, 3GPP Organizational Partners (ARIB, ATIS, CCSA, ETSI, TTA, TTC).All rights reserved.

UMTS is a Trade Mark of ETSI registered for the benefit of its members3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners

LTE is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPPOrganizational PartnersGSM and the GSM logo are registered and owned by the GSM Association

3GPP TS 25.133 V9.0.0 (2009-05)2Release 9

8/14/2019 3gpp Ts 25.133 v9.0.0 (2009-05)

3/233

Contents

Contents....................................................................................................................................................3

Foreword.................................................................................................................................................141 Scope....................................................................................................................................................15

2 References............................................................................................................................................15

3 Definitions, symbols and abbreviations................................................................................................163.1 Definitions............................................................................................................................................................163.2 Symbols................................................................................................................................................................163.3 Abbreviations.......................................................................................................................................................173.4 Test tolerances......................................................................................................................................................18

4 Idle Mode Tasks...................................................................................................................................194.1 Cell Selection.......................................................................................................................................................19

4.1.1 Introduction.......................................................................................................................................................194.2 Cell Re-selection..................................................................................................................................................194.2.1 Introduction.......................................................................................................................................................194.2.2 Requirements.....................................................................................................................................................194.2.2.1 Measurement and evaluation of cell selection criteria S of serving cell........................................................194.2.2.2 Measurements of intra-frequency cells..........................................................................................................204.2.2.3 Measurements of inter-frequency FDD cells.................................................................................................204.2.2.4 Measurements of inter-frequency TDD cells.................................................................................................214.2.2.5 Measurements of inter-RAT GSM cells........................................................................................................214.2.2.5.1 Cell reselection based on cell ranking.........................................................................................................214.2.2.5.2 Cell reselection based on priority information............................................................................................214.2.2.5a Measurements of inter-RAT E-UTRA cells.................................................................................................224.2.2.6 Evaluation of cell re-selection criteria...........................................................................................................23

4.2.2.7 Maximum interruption in paging reception...................................................................................................234.2.2.8 Number of cells in cell lists............................................................................................................................244.2.2.9 Additional requirements for measurement of inter-frequency and inter-RAT cells when MBMS reception is

active .............................................................................................................................................254.2.2.10 MTCH Interruption time..............................................................................................................................254.3 MBSFN cluster selection.....................................................................................................................................25

4.3 MBSFN cluster selection..................................................................................................................254.3.1 Introduction.......................................................................................................................................................25

4.3.1 Introduction....................................................................................................................................254.4 MBSFN cluster reselection..................................................................................................................................25

4.4 MBSFN cluster reselection...............................................................................................................25

4.4.1 Introduction.......................................................................................................................................................254.4.1 Introduction....................................................................................................................................25

5 UTRAN Connected mode mobility......................................................................................................265.1 FDD/FDD Soft Handover....................................................................................................................................265.1.1 Introduction.......................................................................................................................................................265.1.2 Requirements.....................................................................................................................................................265.1.2.1 Active set dimension......................................................................................................................................265.1.2.2 Active set update delay..................................................................................................................................265.1.2.3 Interruption Time...........................................................................................................................................275.2 FDD/FDD Hard Handover...................................................................................................................................275.2.1 Introduction.......................................................................................................................................................275.2.2 Requirements.....................................................................................................................................................27

5.2.2.1 Hard handover delay......................................................................................................................................275.2.2.2 Interruption time.............................................................................................................................................275.3 FDD/TDD Handover............................................................................................................................................285.3.1 Introduction.......................................................................................................................................................28

3GPP

3GPP TS 25.133 V9.0.0 (2009-05)3Release 9

8/14/2019 3gpp Ts 25.133 v9.0.0 (2009-05)

4/233

5.3.2 Requirements.....................................................................................................................................................285.3.2.1 FDD/TDD handover delay.............................................................................................................................285.3.2.2 Interruption time.............................................................................................................................................295.4 FDD/GSM Handover...........................................................................................................................................295.4.1 Introduction.......................................................................................................................................................295.4.2 Requirements.....................................................................................................................................................30

5.4.2.1 Handover delay..............................................................................................................................................305.4.2.2 Interruption time.............................................................................................................................................305.4a FDD to E-UTRAN FDD Handover....................................................................................................................305.4a.1 Introduction.....................................................................................................................................................305.4a.2 Requirements...................................................................................................................................................315.4a.2.1 Handover delay.............................................................................................................................................315.4a.2.2 Interruption time...........................................................................................................................................315.4b FDD to E-UTRAN TDD Handover...................................................................................................................315.4b.1 Introduction.....................................................................................................................................................315.4b.2 Requirements...................................................................................................................................................325.4b.2.1 Handover delay............................................................................................................................................325.4b.2.2 Interruption time...........................................................................................................................................325.5 Cell Re-selection in CELL_FACH......................................................................................................................32

5.5.1 Introduction.......................................................................................................................................................325.5.2 Requirements.....................................................................................................................................................325.5.2.1 Cell re-selection delay....................................................................................................................................335.5.2.1.1 Intra frequency cell reselection...................................................................................................................335.5.2.1.2 Inter frequency cell reselection...................................................................................................................335.5.2.1.3 FDD-TDD cell reselection..........................................................................................................................345.5.2.1.4 UTRAN-GSM Cell Reselection..................................................................................................................345.5.2.2 Interruption time.............................................................................................................................................355.5.2.2.1 FDD-FDD cell reselection..........................................................................................................................355.5.2.2.2 FDD-TDD cell reselection..........................................................................................................................355.5.2.2.3 FDD-GSM cell reselection..........................................................................................................................365.5.2.3 Measurement and evaluation of cell selection criteria S of serving cell........................................................365.6 Cell Re-selection in CELL_PCH.........................................................................................................................36

5.6.1 Introduction.......................................................................................................................................................365.6.2 Requirements.....................................................................................................................................................375.7 Cell Re-selection in URA_PCH...........................................................................................................................375.7.1 Introduction.......................................................................................................................................................375.7.2 Requirements.....................................................................................................................................................375.8 RACH reporting...................................................................................................................................................375.8.1 Introduction.......................................................................................................................................................375.8.2 Requirements.....................................................................................................................................................375.9 Inter-RAT cell change order from UTRAN in CELL_DCH and CELL_FACH.................................................375.9.1 Introduction.......................................................................................................................................................375.9.2 Requirements.....................................................................................................................................................385.9.2.1 Delay 385.9.2.2 Interruption time.............................................................................................................................................38

5.10 Serving HS-DSCH cell change..........................................................................................................................395.10.3 Introduction.....................................................................................................................................................395.10.2 Requirements...................................................................................................................................................395.10.2.1 Serving HS-DSCH cell change delay..........................................................................................................395.10.2.2 Interruption time...........................................................................................................................................395.11 Enhanced Serving HS-DSCH cell change.........................................................................................................395.11.1 Introduction.....................................................................................................................................................395.11.2 Requirements...................................................................................................................................................40

6 RRC Connection Control.....................................................................................................................406.1 RRC Re-establishment.........................................................................................................................................406.1.1 Introduction.......................................................................................................................................................406.1.2 Requirements.....................................................................................................................................................40

6.1.2.1 UE Re-establishment delay requirement........................................................................................................406.2 (void) 416.3 Random Access................................................................................................................................................... .416.3.1 Introduction.......................................................................................................................................................41

3GPP

3GPP TS 25.133 V9.0.0 (2009-05)4Release 9

8/14/2019 3gpp Ts 25.133 v9.0.0 (2009-05)

5/233

6.3.2 Requirements.....................................................................................................................................................416.3.2.1 Correct behaviour when receiving an ACK...................................................................................................416.3.2.2 Correct behaviour when receiving an NACK................................................................................................416.3.2.3 Correct behaviour at Time-out.......................................................................................................................416.3.2.4 Correct behaviour when reaching maximum transmit power........................................................................426.4 Transport format combination selection in UE....................................................................................................42

6.4.1 Introduction.......................................................................................................................................................426.4.2 Requirements.....................................................................................................................................................426.5 Maximum allowed UL TX Power........................................................................................................................446.6 (void) 45

7 Timing and Signalling characteristics..................................................................................................457.1 UE Transmit Timing............................................................................................................................................457.1.1 Introduction.......................................................................................................................................................457.1.2 Requirements.....................................................................................................................................................467.2 UE Receive - Transmit Time Difference.............................................................................................................467.2.1 Introduction.......................................................................................................................................................467.2.2 Requirements.....................................................................................................................................................477.3 UE timer accuracy................................................................................................................................................47

7.3.1 Introduction.......................................................................................................................................................477.3.2 Requirements.....................................................................................................................................................477.4 PRACH Burst timing accuracy............................................................................................................................477.4.1 Introduction.......................................................................................................................................................477.4.2 Requirements.....................................................................................................................................................47

8 UE Measurements Procedures..............................................................................................................488.1 General Measurement Requirements in CELL_DCH State.................................................................................488.1.1 Introduction.......................................................................................................................................................488.1.2 Requirements.....................................................................................................................................................488.1.2.1 UE Measurement Capability..........................................................................................................................488.1.2.2 FDD intra frequency measurements...............................................................................................................498.1.2.2.1 Identification of a new cell..........................................................................................................................498.1.2.2.1.1 Identification of a new cell using IPDL gaps...........................................................................................508.1.2.2.2 UE CPICH measurement capability ...........................................................................................................508.1.2.2.2.1 Capabilities for measurements during IPDL gaps...................................................................................518.1.2.2.3 Periodic Reporting......................................................................................................................................518.1.2.2.4 Event-triggered Periodic Reporting............................................................................................................518.1.2.2.5 Event Triggered Reporting..........................................................................................................................518.1.2.3 FDD inter frequency measurements...............................................................................................................528.1.2.3.1 Identification of a new cell..........................................................................................................................528.1.2.3.2 UE CPICH measurement capability............................................................................................................538.1.2.3.3 Periodic Reporting......................................................................................................................................538.1.2.3.4 Event Triggered Reporting..........................................................................................................................538.1.2.4 TDD measurements........................................................................................................................................548.1.2.4.1 Identification of a new cell..........................................................................................................................548.1.2.4.1.1 3,84 Mcps TDD Option............................................................................................................................548.1.2.4.1.2 1.28 Mcps TDD Option............................................................................................................................558.1.2.4.2 P-CCPCH RSCP measurement period........................................................................................................568.1.2.4.3 Periodic Reporting......................................................................................................................................578.1.2.4.4 Event Triggered Reporting..........................................................................................................................578.1.2.5 GSM measurements.......................................................................................................................................578.1.2.5.1 GSM carrier RSSI.......................................................................................................................................578.1.2.5.2 BSIC verification........................................................................................................................................588.1.2.5.2.1 Initial BSIC identification .......................................................................................................................608.1.2.5.2.2 BSIC re-confirmation...............................................................................................................................618.1.2.5.3 Periodic Reporting......................................................................................................................................618.1.2.5.4 Event Triggered Reporting..........................................................................................................................618.1.2.6 E-UTRAN measurements..............................................................................................................................62

8.1.2.6.1 Identification of a new cell..........................................................................................................................628.1.2.6.2 E-UTRAN RSRP and RSRQ measurement period....................................................................................638.1.2.6.3 Periodic reporting........................................................................................................................................638.1.2.6.4 Void 63

3GPP

3GPP TS 25.133 V9.0.0 (2009-05)5Release 9

8/14/2019 3gpp Ts 25.133 v9.0.0 (2009-05)

6/233

8.1.2.6.5 Event Triggered reporting...........................................................................................................................638.2 Measurements in CELL_DCH State with special requirements..........................................................................648.2.1 Introduction.......................................................................................................................................................648.2.2 Requirements.....................................................................................................................................................648.3 Capabilities for Support of Event Triggering and Reporting Criteria in CELL_DCH state................................648.3.1 Introduction.......................................................................................................................................................64

8.3.2 Requirements.....................................................................................................................................................648.4 Measurements in CELL_FACH State when HS-DSCH discontinuous reception is not ongoing.......................658.4.1 Introduction.......................................................................................................................................................658.4.2 Requirements.....................................................................................................................................................658.4.2.1 UE Measurement Capability when HS-DSCH discontinuous reception is not ongoing...............................658.4.2.2 FDD intra frequency measurements when HS-DSCH discontinuous reception is not ongoing....................668.4.2.2.1 Identification of a new cell..........................................................................................................................678.4.2.2.1.1 Identification of a new cell using IPDL gaps...........................................................................................678.4.2.2.2 UE CPICH measurement capability ...........................................................................................................678.4.2.2.2.1 Capabilities for measurements during IPDL gaps...................................................................................688.4.2.2.3 RACH reporting..........................................................................................................................................688.4.2.3 FDD inter frequency measurements when HS-DSCH discontinuous reception is not ongoing....................688.4.2.3.1 Identification of a new cell..........................................................................................................................68

8.4.2.3.2 UE CPICH measurement capability............................................................................................................698.4.2.4 TDD measurements when HS-DSCH discontinuous reception is not ongoing.............................................698.4.2.4.1 Identification of a new cell..........................................................................................................................698.4.2.4.1.2 1.28 Mcps TDD Option............................................................................................................................708.4.2.4.2 P-CCPCH RSCP measurement period........................................................................................................728.4.2.5 GSM measurements when HS-DSCH discontinuous reception is not ongoing............................................728.4.2.5.1 GSM carrier RSSI.......................................................................................................................................728.4.2.5.2 BSIC verification........................................................................................................................................738.4.2.5.2.1 Initial BSIC identification .......................................................................................................................748.4.2.5.2.2 BSIC re-confirmation...............................................................................................................................758.4a Measurements in CELL_FACH State when HS-DSCH discontinuous reception is ongoing...........................768.4a.1 Introduction.....................................................................................................................................................768.4a.2 Requirements...................................................................................................................................................76

8.4a.2.1 UE Measurement Capability........................................................................................................................768.4.a2.2 FDD intra frequency measurements when HS-DSCH discontinuous reception is ongoing........................768.4.a2.2.1 Identification of a new cell........................................................................................................................768.4a.2.2.2 UE CPICH measurement capability .........................................................................................................778.4.a2.2.3 RACH reporting........................................................................................................................................778.4.a2.3 FDD inter frequency measurements.............................................................................................................778.4a.2.3.1 Identification of a new cell........................................................................................................................778.4a.2.3.2 UE CPICH measurement capability..........................................................................................................788.4a.2.4 TDD measurements when HS-DSCH discontinuous reception is ongoing.................................................788.4.2.4.1 Identification of a new cell..........................................................................................................................788.4.2.4.1.2 1.28 Mcps TDD Option............................................................................................................................798.4a.2.4.2 P-CCPCH RSCP measurement period......................................................................................................818.4a.2.5 GSM measurements when HS-DSCH discontinuous reception is ongoing.................................................81

8.4a.2.5.1 GSM carrier RSSI.....................................................................................................................................828.4a.2.5.2 BSIC verification.......................................................................................................................................828.4a.2.5.2.1 Initial BSIC identification .....................................................................................................................828.4a.2.5.2.2 BSIC re-confirmation.............................................................................................................................828.5 Capabilities for Support of Event Triggering and Reporting Criteria in CELL_FACH state.............................828.5.1 Introduction.......................................................................................................................................................828.5.2 Requirements.....................................................................................................................................................82

9 Measurements Performance Requirements..........................................................................................829.1 Measurement Performance for UE.......................................................................................................................829.1.1 CPICH RSCP....................................................................................................................................................839.1.1.1 Intra frequency measurements accuracy........................................................................................................839.1.1.1.1 Absolute accuracy requirement...................................................................................................................83

9.1.1.1.2 Relative accuracy requirement....................................................................................................................839.1.1.2 Inter frequency measurement accuracy..........................................................................................................849.1.1.2.1 Relative accuracy requirement....................................................................................................................849.1.1.3 CPICH RSCP measurement report mapping.................................................................................................85

3GPP

3GPP TS 25.133 V9.0.0 (2009-05)6Release 9

8/14/2019 3gpp Ts 25.133 v9.0.0 (2009-05)

7/233

9.1.2 CPICH Ec/Io.....................................................................................................................................................859.1.2.1 Intra frequency measurements accuracy........................................................................................................859.1.2.1.1 Absolute accuracy requirement...................................................................................................................859.1.2.1.2 Relative accuracy requirement....................................................................................................................869.1.2.2 Inter frequency measurement accuracy .........................................................................................................879.1.2.2.1 Absolute accuracy requirement...................................................................................................................87

9.1.2.2.2 Relative accuracy requirement....................................................................................................................889.1.2.3 CPICH Ec/Io measurement report mapping..................................................................................................899.1.3 UTRA Carrier RSSI..........................................................................................................................................899.1.3.1 Absolute accuracy requirement......................................................................................................................899.1.3.2 Relative accuracy requirement.......................................................................................................................909.1.3.3 UTRA Carrier RSSI measurement report mapping.......................................................................................909.1.4 GSM carrier RSSI.............................................................................................................................................909.1.4a E-UTRAN RSRP.............................................................................................................................................919.1.4b E-UTRAN RSRQ............................................................................................................................................919.1.5 Transport channel BLER...................................................................................................................................919.1.5.1 BLER measurement requirement...................................................................................................................919.1.5.2 Transport channel BLER measurement report mapping................................................................................919.1.6 UE transmitted power.......................................................................................................................................92

9.1.6.1 Accuracy requirement....................................................................................................................................929.1.6.2 UE transmitted power measurement report mapping.....................................................................................929.1.7 SFN-CFN observed time difference..................................................................................................................929.1.7.1 Intra frequency measurement requirement.....................................................................................................939.1.7.2 Inter frequency measurement requirement.....................................................................................................939.1.7.3 SFN-CFN observed time difference measurement report mapping...............................................................949.1.8 SFN-SFN observed time difference..................................................................................................................959.1.8.1 SFN-SFN observed time difference type 1....................................................................................................959.1.8.1.1 Measurement requirement ..........................................................................................................................959.1.8.1.2 SFN-SFN observed time difference type 1 measurement report mapping.................................................969.1.8.2 SFN-SFN observed time difference type 2....................................................................................................969.1.8.2.1 Intra frequency measurement requirement accuracy without IPDL period active.....................................969.1.8.2.2 Intra frequency measurement requirement accuracy with IPDL period active...........................................97

9.1.8.2.3 Inter frequency measurement requirement accuracy..................................................................................989.1.8.2.4 SFN-SFN observed time difference type 2 measurement report mapping.................................................999.1.9 UE Rx-Tx time difference.................................................................................................................................999.1.9.1 UE Rx-Tx time difference type 1...................................................................................................................999.1.9.1.1 Measurement requirement.........................................................................................................................1009.1.9.1.2 UE Rx-Tx time difference type 1 measurement report mapping..............................................................1009.1.9.2 UE Rx-Tx time difference type 2.................................................................................................................1009.1.9.2.1 Measurement requirement.........................................................................................................................1009.1.9.2.2 UE Rx-Tx time difference type 2 measurement report mapping..............................................................1009.1.10 (void) 1019.1.11 P-CCPCH RSCP...........................................................................................................................................1019.1.11.1 Absolute accuracy requirements................................................................................................................1019.1.11.1.1 3,84 Mcps TDD Option...........................................................................................................................101

9.1.11.1.2 1.28 Mcps TDD Option...........................................................................................................................1029.1.11.2 P-CCPCH RSCP measurement report mapping........................................................................................1029.1.12 UE GPS Timing of Cell Frames for UE positioning.....................................................................................1029.1.12.1 UE GPS timing of Cell Frames for UE positioning measurement report mapping...................................1029.1.13 UE transmission power headroom................................................................................................................1039.1.13.1 Delay requirement......................................................................................................................................1039.1.13.2 Measurement period requirement..............................................................................................................1039.1.13.3 UE transmission power headroom measurement report mapping.............................................................1039.1.13.4 UE transmission power headroom measurement report accuracy.............................................................1049.2 Measurements Performance for UTRAN...........................................................................................................1059.2.1 Received total wideband power......................................................................................................................1059.2.1.1 Absolute accuracy requirement....................................................................................................................1059.2.1.2 Relative accuracy requirement.....................................................................................................................1069.2.1.3 Received total wideband power measurement report mapping...................................................................1069.2.2 SIR 1069.2.2.1 Accuracy requirement..................................................................................................................................106

3GPP

3GPP TS 25.133 V9.0.0 (2009-05)7Release 9

8/14/2019 3gpp Ts 25.133 v9.0.0 (2009-05)

8/233

8/14/2019 3gpp Ts 25.133 v9.0.0 (2009-05)

9/233

Annex A (normative):

Test Cases............................................................................................118

A.1 Purpose of Annex...........................................................................................................................118

A.2 Requirement classification for statistical testing.............................................................................118A.2.1 Types of requirements in TS 25.133..............................................................................................................118

A.3 RRM test configurations.................................................................................................................119A.3.1 UE with single antenna connector..................................................................................................................119A.3.2 UE with multiple antenna connectors............................................................................................................119

A.4 Idle Mode.......................................................................................................................................120A.4.1 (void)..............................................................................................................................................................120A.4.2 Cell Re-Selection............................................................................................................................................120A.4.2.1 Scenario 1: Single carrier case....................................................................................................................120A.4.2.1.1 Test Purpose and Environment................................................................................................................120A.4.2.1.2 Test Requirements....................................................................................................................................121A.4.2.2 Scenario 2: Multi carrier case......................................................................................................................121A.4.2.2.1 Test Purpose and Environment................................................................................................................121

A.4.2.2.2 Test Requirements....................................................................................................................................122A.4.3 UTRAN to GSM Cell Re-Selection...............................................................................................................123A.4.3.1 Scenario 1....................................................................................................................................................123A.4.3.1.1 Test Purpose and Environment................................................................................................................123A.4.3.1.2 Test Requirements....................................................................................................................................124A.4.3.2 Scenario 2....................................................................................................................................................124A.4.3.2.1 Test Purpose and Environment................................................................................................................124A.4.3.2.2 Test Requirements....................................................................................................................................125A.4.3.3 Scenario 3....................................................................................................................................................126A.4.3.3.1 Test Purpose and Environment................................................................................................................126A.4.3.3.2 Test Requirements....................................................................................................................................127A.4.4 FDD/TDD Cell Re-selection..........................................................................................................................127A.4.4.1 Test Purpose and Environment...................................................................................................................127

A.4.4.1.1 3,84 Mcps TDD Option............................................................................................................................127A.4.4.1.2 1.28 Mcps TDD Option............................................................................................................................129A.4.4.2 Test Requirements.......................................................................................................................................130A.4.5 UTRAN to E-UTRA Cell Reselection...........................................................................................................131A.4.5.1 E-UTRA FDD is of higher priority.............................................................................................................131A.4.5.1.1 Test Purpose and Environment................................................................................................................131A.4.5.1.2 Test Requirements....................................................................................................................................134A.4.5.2 E-UTRA FDD is of lower priority..............................................................................................................134A.4.5.2.1 Test Purpose and Environment................................................................................................................134A.4.5.2.2 Test Requirements....................................................................................................................................136

A.5 UTRAN Connected Mode Mobility...............................................................................................137A.5.1 FDD/FDD Soft Handover..............................................................................................................................137A.5.1.1 Test Purpose and Environment...................................................................................................................137A.5.1.1.1 Test procedure..........................................................................................................................................138A.5.1.2 Test Requirements.......................................................................................................................................138A.5.2 FDD/FDD Hard Handover.............................................................................................................................138A.5.2.1 Handover to intra-frequency cell.................................................................................................................138A.5.2.1.1 Test Purpose and Environment................................................................................................................138A.5.2.1.2 Test Requirements....................................................................................................................................139A.5.2.2 Handover to inter-frequency cell ................................................................................................................139A.5.2.2.1 Test Purpose and Environment................................................................................................................139A.5.2.2.2 Test Requirements....................................................................................................................................140A.5.3 (void)..............................................................................................................................................................141A.5.4 Inter-system Handover from UTRAN FDD to GSM.....................................................................................141A.5.4.1 Test Purpose and Environment...................................................................................................................141

A.5.4.2 Test Requirements.......................................................................................................................................143A.5.4a Inter-system Handover from UTRAN FDD to E-UTRAN FDD.................................................................143A.5.4a.1 Test Purpose and Environment..................................................................................................................143A.5.4a.2 Test Requirements.....................................................................................................................................146

3GPP

3GPP TS 25.133 V9.0.0 (2009-05)9Release 9

8/14/2019 3gpp Ts 25.133 v9.0.0 (2009-05)

10/233

A.5.4b Inter-system Handover from UTRAN FDD to E-UTRAN TDD.................................................................146A.5.4b.1 Test Purpose and Environment.................................................................................................................146A.5.4b.2 Test Requirements.....................................................................................................................................149A.5.5 Cell Re-selection in CELL_FACH................................................................................................................149A.5.5.1 One frequency present in neighbour list.....................................................................................................149A.5.5.1.1 Test Purpose and Environment................................................................................................................149

A.5.5.1.2 Test Requirements....................................................................................................................................150A.5.5.2 Two frequencies present in the neighbour list ...........................................................................................151A.5.5.2.1 Test Purpose and Environment................................................................................................................151A.5.5.2.2 Test Requirements....................................................................................................................................152A.5.5.3 Cell Reselection to GSM.............................................................................................................................153A.5.5.3.1 Test Purpose and Environment................................................................................................................153A.5.5.3.2 Test Requirements....................................................................................................................................154A.5.5.4 Cell Reselection during an MBMS session, two frequencies present in neighbour list..............................155A.5.5.4.1 Test Purpose and Environment................................................................................................................155A.5.5.4.2 Test Requirements....................................................................................................................................157A.5.6 Cell Re-selection in CELL_PCH...................................................................................................................158A.5.6.1 One frequency present in the neighbour list................................................................................................158A.5.6.1.1 Test Purpose and Environment................................................................................................................158

A.5.6.1.2 Test Requirements....................................................................................................................................159A.5.6.2 Two frequencies present in the neighbour list............................................................................................159A.5.6.2.1 Test Purpose and Environment................................................................................................................159A.5.6.2.2 Test Requirements....................................................................................................................................160A.5.6.3 Cell re-selection during an MBMS session, one UTRAN inter-frequency and 2 GSM cells present in the

neighbour list ....................................................................................................................................161A.5.6.3.1 Test Purpose and Environment................................................................................................................161A.5.6.3.2 Test Requirements....................................................................................................................................163A.5.7 Cell Re-selection in URA_PCH.....................................................................................................................163A.5.7.1 One frequency present in the neighbour list................................................................................................163A.5.7.1.1 Test Purpose and Environment................................................................................................................163A.5.7.1.2 Test Requirements....................................................................................................................................164A.5.7.2 Two frequencies present in the neighbour list............................................................................................164

A.5.7.2.1 Test Purpose and Environment................................................................................................................164A.5.7.2.2 Test Requirements....................................................................................................................................165A.5.8 Serving HS-DSCH cell change......................................................................................................................166A.5.8.1 Test Purpose and Environment...................................................................................................................166A.5.8.1.1 Test procedure..........................................................................................................................................167A.5.8.2 Test Requirements.......................................................................................................................................167A.5.9 Enhanced Serving HS-DSCH cell change.....................................................................................................167A.5.9.1 Test Purpose and Environment...................................................................................................................167A.5.9.1.1 Test procedure..........................................................................................................................................169A.5.9.2 Test Requirements.......................................................................................................................................169

A.6 RRC Connection Control...............................................................................................................169A.6.1 RRC Re-establishment delay.........................................................................................................................169

A.6.1.1 Test Purpose and Environment...................................................................................................................169A.6.1.1.1 TEST 1.....................................................................................................................................................169A.6.1.1.2 TEST 2.....................................................................................................................................................170A.6.1.2 Test Requirements.......................................................................................................................................171A.6.1.2.1 Test 1 171A.6.1.2.2 Test 2 172A.6.2 Random Access..............................................................................................................................................172A.6.2.1 Test Purpose and Environment...................................................................................................................172A.6.2.2 Test Requirements.......................................................................................................................................174A.6.2.2.1 Correct behaviour when receiving an ACK.............................................................................................174A.6.2.2.2 Correct behaviour when receiving an NACK..........................................................................................174A.6.2.2.3 Correct behaviour at Time-out.................................................................................................................174A.6.2.2.4 Correct behaviour when reaching maximum transmit power..................................................................174

A.6.3 (void)..............................................................................................................................................................174A.6.4 Transport format combination selection in UE..............................................................................................174A.6.4.1 Test Purpose and Environment...................................................................................................................174A.6.4.1.1 Interactive or Background, PS, UL: 64 kbps...........................................................................................175

3GPP

3GPP TS 25.133 V9.0.0 (2009-05)10Release 9

8/14/2019 3gpp Ts 25.133 v9.0.0 (2009-05)

11/233

A.6.4.2 Test Requirements.......................................................................................................................................176A.6.4.2.1 Interactive or Background, PS, UL: 64 kbps...........................................................................................176A.6.5 (void)..............................................................................................................................................................177A.6.6 E-TFC restriction in UE.................................................................................................................................177A.6.6.1 Test Purpose and Environment...................................................................................................................177A.6.6.1.1 10ms TTI E-DCH E-TFC restriction testcase..........................................................................................177

A.6.6.1.1.1 Test Requirements.................................................................................................................................179A.6.6.1.2 2ms TTI E-DCH E-TFC restriction testcase............................................................................................180A.6.6.1.2.1 Test Requirements.................................................................................................................................182

A.7 Timing and Signalling Characteristics............................................................................................183A.7.1 UE Transmit Timing......................................................................................................................................183A.7.1.1 Test Purpose and Environment...................................................................................................................183A.7.1.2 Test Requirements.......................................................................................................................................184

A.8 UE Measurements Procedures........................................................................................................185A.8.1 FDD intra frequency measurements...............................................................................................................185A.8.1.1 Event triggered reporting in AWGN propagation conditions.....................................................................185A.8.1.1.1 Test Purpose and Environment................................................................................................................185A.8.1.1.2 Test Requirements....................................................................................................................................186

A.8.1.2 Event triggered reporting of multiple neighbours in AWGN propagation condition.................................186A.8.1.2.1 Test Purpose and Environment................................................................................................................186A.8.1.2.2 Test Requirements....................................................................................................................................187A.8.1.3 Event triggered reporting of two detectable neighbours in AWGN propagation condition.......................188A.8.1.3.1 Test Purpose and Environment................................................................................................................188A.8.1.3.2 Test Requirements....................................................................................................................................189A.8.1.4 Correct reporting of neighbours in fading propagation condition...............................................................189A.8.1.4.1 Test Purpose and Environment................................................................................................................189A.8.1.4.2 Test Requirements....................................................................................................................................190A.8.1.5 Event triggered reporting of multiple neighbour cells in Case 1 fading condition.....................................190A.8.1.5.1 Test Purpose and Environment................................................................................................................190A.8.1.5.2 Test Requirements....................................................................................................................................191A.8.1.6 Event triggered reporting of multiple neighbour cells in Case 3 fading condition.....................................192A.8.1.6.1 Test Purpose and Environment................................................................................................................192A.8.1.6.2 Test Requirements....................................................................................................................................193A.8.2 FDD inter frequency measurements...............................................................................................................193A.8.2.1 Correct reporting of neighbours in AWGN propagation condition............................................................193A.8.2.1.1 Test Purpose and Environment................................................................................................................193A.8.2.1.2 Test Requirements....................................................................................................................................194A.8.2.2 Correct reporting of neighbours in Fading propagation condition..............................................................195A.8.2.2.1 Test Purpose and Environment................................................................................................................195A.8.2.2.2 Test Requirements....................................................................................................................................195A.8.2.3 Correct reporting of neighbours in fading propagation condition using TGL1=14....................................196A.8.2.3.1 Test Purpose and Environment................................................................................................................196A.8.2.3.2 Test Requirements....................................................................................................................................196A.8.2A FDD adjacent frequency measurements......................................................................................................197A.8.2A.1 Event triggered reporting in AWGN propagation conditions..................................................................197A.8.2A.1.1 Test Purpose and Environment..............................................................................................................197A.8.2A.1.2 Test Requirements............................................................................................................................... ..198A.8.2A.2 Event triggered reporting of two detectable neighbours in AWGN propagation condition....................198A.8.2A.2.1 Test Purpose and Environment..............................................................................................................198A.8.2A.2.2 Test Requirements............................................................................................................................... ..199A.8.2A.3 Correct reporting of neighbours in fading propagation condition............................................................200A.8.2A.3.1 Test Purpose and Environment..............................................................................................................200A.8.2A.3.2 Test Requirements............................................................................................................................... ..201A.8.3 (void)..............................................................................................................................................................201A.8.4 GSM measurements.......................................................................................................................................201A.8.4.1 Correct reporting of GSM neighbours in AWGN propagation condition...................................................201

A.8.4.1.1 Test Purpose and Environment................................................................................................................201A.8.4.1.1.1 Test 1. With BSIC verification required...............................................................................................202A.8.4.1.1.2 Test 2: Without BSIC verification required..........................................................................................204A.8.4.1.2 Test Requirements....................................................................................................................................205

3GPP

3GPP TS 25.133 V9.0.0 (2009-05)11Release 9

8/14/2019 3gpp Ts 25.133 v9.0.0 (2009-05)

12/233

A.8.4.1.2.1 TEST 1 With BSIC verification required..............................................................................................205A.8.4.1.2.2 TEST 2 Without BSIC verification required.........................................................................................205A.8.5 Combined Interfrequency and GSM measurements......................................................................................205A.8.5.1 Correct reporting of neighbours in AWGN propagation condition............................................................205A.8.5.1.1 Test Purpose and Environment................................................................................................................205A.8.5.1.2 Test Requirements....................................................................................................................................207

A.8.6 E-UTRAN Measurements..............................................................................................................................207A.8.6.1 Correct reporting of E-UTRAN FDD neighbours in fading propagation condition...................................207A.8.6.1.1 Test Purpose and Environment................................................................................................................207A.8.6.1.2 Test Requirements....................................................................................................................................209A.8.6.2 Correct reporting of E-UTRAN TDD neighbours in fading propagation condition...................................210A.8.6.2.1 Test Purpose and Environment................................................................................................................210A.8.6.2.2 Test Requirements....................................................................................................................................212

A.9 Measurement Performance Requirements......................................................................................213A.9.1 Measurement Performance for UE.................................................................................................................213A.9.1.1 CPICH RSCP..............................................................................................................................................213A.9.1.1.1 Test Purpose and Environment................................................................................................................213A.9.1.1.1.1 Intra frequency test parameters.............................................................................................................213

A.9.1.1.1.2 Inter frequency test parameters.............................................................................................................214A.9.1.1.2 Test Requirements....................................................................................................................................215A.9.1.2 CPICH Ec/Io...............................................................................................................................................215A.9.1.2.1 Test Purpose and Environment................................................................................................................215A.9.1.2.1.1 Intra frequency test parameters.............................................................................................................215A.9.1.2.1.2 Inter frequency test parameters.............................................................................................................216A.9.1.2.2 Test Requirements....................................................................................................................................217A.9.1.3 UTRA Carrier RSSI....................................................................................................................................218A.9.1.3.1 Test Purpose and Environment................................................................................................................218A.9.1.3.2 Test Requirements....................................................................................................................................219A.9.1.3A GSM Carrier RSSI....................................................................................................................................220A.9.1.3A.1 Test Purpose and Environment..............................................................................................................220A.9.1.3A.2 Test Requirements............................................................................................................................... ..221

A.9.1.3B Transport channel BLER..........................................................................................................................221A.9.1.3C UE transmitted power...............................................................................................................................221A.9.1.3C.1 Test Purpose and Environment..............................................................................................................221A.9.1.3C.1.1 Test procedure....................................................................................................................................222A.9.1.3C.2 Test Requirements.................................................................................................................................222A.9.1.4 SFN-CFN observed time difference............................................................................................................222A.9.1.4.1 Test Purpose and Environment................................................................................................................222A.9.1.4.1.1 Intra frequency test parameters.............................................................................................................222A.9.1.4.1.2 Inter frequency test parameters.............................................................................................................223A.9.1.4.2 Test Requirements....................................................................................................................................224A.9.1.5 SFN-SFN observed time difference............................................................................................................224A.9.1.5.1 SFN-SFN observed time difference type 1..............................................................................................224A.9.1.5.1.1 Test Purpose and Environment.............................................................................................................224

A.9.1.5.1.2 Test Requirements.................................................................................................................................224A.9.1.5.2 SFN-SFN observed time difference type 2 without IPDL period active.................................................224A.9.1.5.2.1 Test Purpose and Environment.............................................................................................................224A.9.1.5.2.2 Test Requirements.................................................................................................................................225A.9.1.5.3 SFN-SFN observed time difference type 2 with IPDL period active......................................................225A.9.1.5.3.1 Test Purpose and Environment.............................................................................................................225A.9.1.5.3.2 Test Requirements.................................................................................................................................226A.9.1.6 UE Rx-Tx time difference...........................................................................................................................226A.9.1.6.1 UE Rx-Tx time difference type 1.............................................................................................................226A.9.1.6.1.1 Test Purpose and Environment.............................................................................................................226A.9.1.6.1.2 Test Requirements.................................................................................................................................227A.9.1.6.2 UE Rx-Tx time difference type 2.............................................................................................................227A.9.1.6.2.1 Test Purpose and Environment.............................................................................................................227

A.9.1.6.2.2 Test Requirements.................................................................................................................................228A.9.1.7 (void)228A.9.1.8 (void)228A.9.1.9 UE Transmission Power Headroom............................................................................................................228

3GPP

3GPP TS 25.133 V9.0.0 (2009-05)12Release 9

8/14/2019 3gpp Ts 25.133 v9.0.0 (2009-05)

13/233

A.9.1.9.1 Test Purpose and Environment................................................................................................................228A.9.1.9.1.1 Test Procedure.......................................................................................................................................229A.9.1.9.2 Test Requirements....................................................................................................................................229

Annex B (informative):

Change History....................................................................................231

3GPP

3GPP TS 25.133 V9.0.0 (2009-05)13Release 9

8/14/2019 3gpp Ts 25.133 v9.0.0 (2009-05)

14/233

8/14/2019 3gpp Ts 25.133 v9.0.0 (2009-05)

15/233

1 ScopeThe present document specifies requirements for support of Radio Resource Management for FDD. These requirementsinclude requirements on measurements in UTRAN and the UE as well as requirements on node dynamical behaviour

and interaction, in terms of delay and response characteristics.

2 ReferencesThe following documents contain provisions which, through reference in this text, constitute provisions of the presentdocument.

References are either specific (identified by date of publication, edition number, version number, etc.) ornon-specific.

For a specific reference, subsequent revisions do not apply.

For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document(including a GSM document), a non-specific reference implicitly refers to the latest version of that documentin the same Release as the present document.

[1] 3GPP TS 25.304: "UE Procedures in Idle Mode and Procedures for Cell Reselection in ConnectedMode".

[2] 3GPP TS 25.211: "Physical channels and mapping of transport channels onto physical channels(FDD)".

[3] 3GPP TS 25.101: "UE Radio transmission and reception (FDD)".

[4] 3GPP TS 25.104: "BTS Radio transmission and reception (FDD)".

[5] 3GPP TS 25.102: "UE Radio transmission and reception (TDD)".

[6] 3GPP TS 25.105: "BTS Radio transmission and reception (TDD)".

[7] 3GPP TS 25.212: "Multiplexing and channel coding (FDD)".

[8] 3GPP TS 25.141: "Base station conformance testing (FDD)".

[9] 3GPP TS 25.142: "Base station conformance testing (TDD)".

[10] 3GPP TS 25.113: "Base station EMC".

[11] 3GPP TR 25.942: "RF System scenarios".

[12] 3GPP TR 25.922: "RRM Strategies".[13] 3GPP TS 25.215: "Physical Layer Measurements (FDD)".

[14] 3GPP TS 25.225: "Physical Layer Measurements (TDD)".

[15] 3GPP TS 25.302: "Services provided by Physical Layer".

[16] 3GPP TS 25.331: "RRC Protocol Specification".

[17] ETSI ETR 273-1-2: "Electromagnetic compatibility and Radio spectrum Matters (ERM);Improvement of radiated methods of measurement (using test sites) and evaluation of thecorresponding measurement uncertainties; Part 1: Uncertainties in the measurement of mobileradio equipment characteristics; Sub-part 2: Examples and annexes".

[18] 3GPP TS 25.214: "Physical layer procedures (FDD)"

[19] 3GPP TS 25.321: "MAC protocol specification"

3GPP

3GPP TS 25.133 V9.0.0 (2009-05)15Release 9

8/14/2019 3gpp Ts 25.133 v9.0.0 (2009-05)

16/233

[20] 3GPP TS 25.303: "Interlayer Procedures in Connected Mode".

[21] 3GPP TS 45.008: "Radio subsystem link control".

[22] 3GPP TS 45.005: "Radio transmission and reception".

[23] 3GPP TS 26.103: "Speech Codec List for GSM and UMTS".

[24] 3GPP TS 36.133: "Requirements for support of radio resource management".

[25] 3GPP TS 36.304: "User Equipment (UE) procedures in idle mode".

3 Definitions, symbols and abbreviations

3.1 DefinitionsFor the purposes of the present document, the following terms and definitions apply.

The main general definitions strictly related to the Transmission and Reception characteristics but important also for thepresent document can be found in [3] for UE FDD, in [4] for BS FDD, in [5] for UE TDD, in [6] for BS TDD.

Node B:A logical node responsible for radio transmission / reception in one or more cells to/from the User Equipment.Terminates the Iub interface towards the RNC

Power Spectral Density: The units of Power Spectral Density (PSD) are extensively used in this document. PSD is afunction of power versus frequency and when integrated across a given bandwidth, the function represents the mean

power in such a bandwidth. When the mean power is normalised to (divided by) the chip-rate it represents the meanenergy per chip. Some signals are directly defined in terms of energy per chip, (DPCH_Ec, Ec, OCNS_Ec and S-CCPCH_Ec) and others defined in terms of PSD (Io, Ioc, Ior and or). There also exist quantities that are a ratio of energy

per chip to PSD (DPCH_Ec/Ior, Ec/Ioretc.). This is the common practice of relating energy magnitudes in communicationsystems.It can be seen that if both energy magnitudes in the ratio are divided by time, th

Documents

3gpp Ts 25.133 v9.0.0 (2009-05)