4G LTE Integration Training

HUAWEI TECHNOLOGIES CO., LTD.

www.huawei.com

Huawei Confidential

Security Level:

4G LTE Integration

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential

Types of site connectivity:

Page 2

eNodeB

eNodeB

eNodeB

GE/FE Cable

Fiber Cable

MW RTN900

GPON MDU (SmartAx)

Fiber Cable

Exchange OLT

1- GPON site.

2- Microwave site.

3- Dark Fiber site.


GPON connection

Page 3

4G 3G 2G

For 4G , 3G and 2G use FE/GE cable.

GPON MDU (SmartAx)


Microwave Connection

Page 4

MW RTN950


Microwave Connection

Page 5

EM6F Card of RTN950

4G 3G 2G

For 4G and 3G use LC to LC Fiber cable

For 2G use FE/GE cable


DF Connection

Page 6

Connect Fiber cable to ODF in

Exchange site to the

assigned Port ( you can know

which port from JISOW

sheet ).


LTE BBU connection

Page 7

or DF

For MW and DF use SFP0 port , For GPON use FE0/GE0 Port


LTE 4G IntegrationMain Job on site: Use WEBLMT to login the eNodeB Add the OM link and check the link status

Steps Of Job: Use WEBLMT to login the eNodeB Use the Ethernet cable to connect to ETH port of LMPT board. Configure the IP 192.168.0.2 on laptop. Use IE Browser and visit the website: http://192.168.0.49/ Username ： admin Password ： admin123 You must have JISOW sheet for IPs and VLAN

Page 8


1. SET DHCPSW: SWITCH=DISABLE;

2. SET ETHPORT to modify as the picture below:

Page 9

GPON : Port Attribute = Copper

MW : Port Attribute = Fiber


3. DSP ETHPORT: SN=7, SBT=BASE_BOARD; To check

port statusDSP ETHPORT Result------------------ Cabinet No. = 0 Subrack No. = 0 Slot No. = 7 Subboard Type = Base Board Port No. = 0 Port Attribute = Copper Port Status = Up Physical Layer Status = Up Maximum Transmission Unit(byte) = 1500 ARP Proxy = Enable Flow Control = Open MAC Address = 707B-E8C5-8B9A Loopback Status = No Loop In Loopback Mode or Not = No Ethernet OAM 3AH Flag = Disable Number of RX Packets(packet) = 444334 Number of RX Bytes(byte) = 79380405Number of RX CRC Error Packets(packet) = 4 RX Traffic(byte/s) = 257 Number of TX Packets(packet) = 215850 Number of TX Bytes(byte) = 40290597 TX Traffic(byte/s) = 146 Local Configuration Negotiation Mode = Automatic Negotiation Local Actual Negotiation Mode = Automatic Negotiation Local Speed = 1000M Local Duplex = Full Duplex Peer Actual Negotiation Mode = Unknown Peer Speed = 1000M Peer Duplex = Unknown Number of IPs = 2 IP Address List = 10.226.5.193 255.255.255.252 = 10.140.10.193 255.255.255.252(Number of results = 1)

Page 10


4. ADD DEVIP:;

As picture below:

5. ADD VLANMAP:;

Page 11

0

O&M Host IP in JISOW From JISOW

VLAN ID (OaM) in JISOW

O&M DGW in JISOW From JISOW


6. ADD OMCH:;

Page 12

O&M Host IP in JISOW

O&M DGW in JISOW

From JISOW


7. Ping:;

Tow destination: PING from Local IP to GW IP PING from Local IP to destination IP

(172.20.110.127)

Page 13


Ping Result must be as follow:

Page 14


8. Copy the Script Below To Batch section and press

GO and wait till finish.

Page 15

Script.txt


9. ADD GPS: SN=7, CABLETYPE=COAXIAL,

CABLE_LEN=45, PRI=1;

10. SET CLKSYNCMODE: CLKSYNCMODE=TIME;

Page 16

Select Time


11. DSP GPS: GN=0;

* Make sure the GPS Card State is Normal; And the GPS

Satellites Traced is larger than 8.

Page 17


12. STR VSWRTEST:;

Be sure all VSWR values below 140

Page 18


At Last when every things Ok Call integration Team

to make complete integration remotely after

confirm to you status is ok you can leave site.

Page 19


Some Cases

Ethernet Port wrong configured.

Only can ping to GW but you cannot ping to Peer IP

(M2000).

Page 20


Thanks

Page 21

Documents

4G LTE Integration Training