314
8/9/2019 9500 MPR O _26 M http://slidepdf.com/reader/full/9500-mpr-o-26-m 1/314 9500 MPR Operation and Administration PN 3EM23954AB 01 R01.02, Issue 01, February 2010

9500 MPR O _26 M

Embed Size (px)

Citation preview

Page 1: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 1/314

9500 MPROperation and Administration

PN 3EM23954AB 01

R01.02, Issue 01, February 2010

Page 2: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 2/314

© Alcatel-Lucent 2010 - All Rights ReservedPrinted in U.S.A.

THIS PRODUCT COMPLIES WITH D.H.H.S. RADIATION PERFORMANCE STANDARDS 21

CFR, 1040.10, FOR A CLASS 1 LASER PRODUCT.

DANGER

Invisible laser radiation is present when the optic connector is open. AVOID DIRECT

EXPOSURE TO BEAM.

WARNING

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case users will be required to correct the

interference at their own expense.

NOTICE

This manual applies to 9500 MPR R01.02 software. Release notes describing revisions to this software may

impact operations described in this manual.

This transfer of commodities, technology, or software, if from the United States, is an export in accordance

with the U.S. Export Administration Regulations. Diversion contrary to U.S. law is prohibited. The export or 

re-export (further transfer) of such commodities, technology, software or products made from such

technology is prohibited without proper authorization(s) from the U.S. Department of Commerce or other 

appropriate U.S. government agency(s).

 All rights reserved. No part of this manual may be reproduced, translated, stored in a retrieval system, or 

transmitted or distributed by any means, electronic or mechanical, by photocopying, recording, or otherwise,

without the written permission of Alcatel-Lucent. Preparing derivative works or providing instruction basedon the material is prohibited unless agreed to in writing by Alcatel-Lucent.

The product specification and/or performance levels contained in this document are for information

purposes only and are subject to change without notice. They do not represent any obligation on the part of 

 Alcatel-Lucent. Such obligations will only be committed to in a written sales agreement signed by

 Alcatel-Lucent.

DOCUMENTATION

Product documentation is available on Alcatel-Lucent’s OnLine Customer Support web site at

https://support.lucent.com/portal/olcsHome.do.

To offer comments on this documentation, visit Alcatel-Lucent’s OnLine Customer Support web site at

https://support.lucent.com/portal/olcsHome.do and select Contact us, Customer support , and then OnLine

 Assistance or write to the following address.

 Alcatel-Lucent

 Attention: Doc Comment, M/S RND-1

3400 W. Plano Pkwy.

Plano, Texas 75075-0811 USA

Page 3: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 3/314

3EM23954ABIssue 01, February 2010

© Alcatel-Lucent 2010 - All Rights Reserved i

 ALCATEL-LUCENT PRACTICEStandard

9500 MPR Operation and AdministrationTable of Contents

Introduction

1. OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Writing Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

 Admonishments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Related Documentation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Document Types  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

2. PRODUCT SUPPORT INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Product Documentation and Training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Technical Support Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5Repair and Return Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Spare Parts and Replacement Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Service Center  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Installation and Maintenance Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Index Task Lists (IXLs)

IXL-100 Index Task List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

IXL-101 User Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

IXL-102 Equipment Provisioning and Deprovisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

IXL-103 System Information Reports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

IXL-104 System Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

IXL-105 Equipment Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Non-trouble Procedures (NTPs)

NTP-100 DS1 Provisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

NTP-101 DS3 Provisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

NTP-102 Ethernet Provisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

NTP-103 DS1 Deprovisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

NTP-104 DS3 Deprovisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Page 4: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 4/314

3EM23954ABIssue 01, February 2010

Table of Contentsii

NTP-105 Ethernet Deprovisioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

Detailed Level Procedures (DLPs)

DLP-100 Log Into and Out of System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

DLP-101 Administer User Profiles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

DLP-102 Configure PC Network Card to Connect to NE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15

DLP-103 Change Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21

DLP-104 Enable Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23

DLP-105 Disable Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39

DLP-106 Provision Equipment Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-55

DLP-107 Deprovision Equipment Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-69

DLP-108 Provision Ethernet Ports  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-81

DLP-109 Provision Radio Parameters  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-87

DLP-110 Provision Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-93

DLP-112 Provision Cross Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-99

DLP-113 View Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-115

DLP-114 View Abnormal Condition List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-119

DLP-115 View Protection Schemes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-121

DLP-116 Download Provisioning Data  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-129

DLP-117 Administer System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-135

DLP-118 Administer Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-143

DLP-119 Administer System Date and Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-153

DLP-120 Administer Software License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-159

DLP-121 Perform Protection Switching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-163

DLP-122 Performance Monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-179

Page 5: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 5/314

3EM23954ABIssue 01, February 2010

Table of Contents iii

DLP-123 Perform Radio Power Measurements  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-195

DLP-126 Deprovision Cross Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-199

DLP-127 Deprovision Ethernet Ports  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-205

DLP-128 Administer NE Lists  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-211

DLP-129 View Event Log  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-223

DLP-130 IF Cable Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-227

DLP-131 MIB Database Management (Backup and Restore)  . . . . . . . . . . . . . . . . . . . . . . . . . 4-239

DLP-132 Load System and Craft Terminal Software on PC . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-247

WebEML Craft Terminal Reference Guide

1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Main Screen Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Page 6: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 6/314

3EM23954ABIssue 01, February 2010

Table of Contentsiv

Page 7: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 7/314

3EM23954ABIssue 01, February 2010

List of Figures v

9500 MPR Operation and AdministrationList of Figures

Figure 100-1. MPR-A R01.02 WebEML Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Figure 100-2. NETO Overview Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Figure 100-3. NETO Login Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Figure 100-4. JUSM/CT 9500MPR-A Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

Figure 100-5. JUSM/CT 9500MPR-A Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Figure 100-6. NETO Overview Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Figure 101-1. User Management Drop-Down Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Figure 101-2. Profile Management Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Figure 101-3. Create User Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Figure 101-4. Profile Management Window - with Added User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Figure 101-5. User Management Drop-Down Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Figure 101-6. Profile Management Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Figure 101-7. Delete User Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Figure 101-8. Profile Management Window - with User Deleted . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

Figure 101-9. User Management Drop-Down Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

Figure 101-10.Profile Management Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

Figure 101-11.Change User Password Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

Figure 102-1. Internet Protocol (TCP/IP) Properties Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16

Figure 102-2. Internet Protocol (TCP/IP) Properties Window Configured for DHCP . . . . . . . . . . . . . 4-17

Figure 102-3. Internet Protocol (TCP/IP) Properties Window Configured to Use a specificIP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18

Figure 102-4. Run Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19

Figure 102-5. DOS Command Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19

Page 8: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 8/314

3EM23954ABIssue 01, February 2010

List of Figuresvi

Figure 102-6. Successful Ping Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

Figure 103-1. User Change Password Drop-Down Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21

Figure 103-2. Changing Password Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22

Figure 104-1. Select Slot 2 to Enable Protect CSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24

Figure 104-2. Select Protect CSM Equipment Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

Figure 104-3. Protect CSM Enabled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26

Figure 104-4. Select Slot 9 to Enable FAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27

Figure 104-5. Select FAN Equipment Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28

Figure 104-6. FAN Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29

Figure 104-7. Select Slot to Enable MOD300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30

Figure 104-8. Select MD300 Equipment Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31

Figure 104-9. MOD300 Enabled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32

Figure 104-10.Select Slot to Enable P32E1DS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33

Figure 104-11.Select P32EDS1 Equipment Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34

Figure 104-12.P32E1DS1 Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35

Figure 104-13.Select Slot to Enable P2E3DS3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36

Figure 104-14.Select P2E3DS3 Equipment Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37

Figure 104-15.P2E3DS3 Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38

Figure 105-1. Enabled Spare CSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-40

Figure 105-2. Disable Protect CSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-41

Figure 105-3. Protect CSM Disabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-42

Figure 105-4. Enabled FAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-43

Figure 105-5. Disable FAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-44

Figure 105-6. FAN Disabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-45

Page 9: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 9/314

3EM23954ABIssue 01, February 2010

List of Figures vii

Figure 105-7. Enabled MOD300. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-46

Figure 105-8. Disable MOD300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-47

Figure 105-9. MOD300 Disabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-48

Figure 105-10.Enabled P32E1DS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-49

Figure 105-11.Disable P32E1DS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-50

Figure 105-12.Disabled P32E1DS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-51

Figure 105-13.Enabled P2E3DS3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-52

Figure 105-14.Disable P2E3DS3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53

Figure 105-15.Disabled P2E3DS3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-54

Figure 106-1. Resource List Area: CSM SFP Slot Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-56

Figure 106-2. Provision CSM SFP Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-57

Figure 106-3. Provisioned CSM SFP Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-58

Figure 106-4. Resource List Area: P32E1DS1 Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-59

Figure 106-5. Provision P32E1DS1 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-60

Figure 106-6. Provisioned P32E1DS1 TDM2TDM Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-61

Figure 106-7. Provision P32E1DS1 for TDM2ETH Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-62

Figure 106-8. Provisioned P32E1DS1 TDM2ETH Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-63

Figure 106-9. Resource List Area: P2E3DS3 Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-64

Figure 106-10.Provision P2E3DS3 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-65

Figure 106-11.Provisioned P2E3DS3 TDM2TDM Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-66

Figure 106-12.Provision P2E3DS3 for TDM2ETH Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-67

Figure 106-13.Provisioned P2E3DS3 TDM2ETH Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-68

Figure 107-1. Resource List Area: CSM SFP Slot Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-70

Figure 107-2. Provisioned CSM SFP Port #5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-71

Page 10: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 10/314

3EM23954ABIssue 01, February 2010

List of Figuresviii

Figure 107-3. Deprovisioned CSM SFP Port#5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-72

Figure 107-4. Resource List Area: P32E1DS1 Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-73

Figure 107-5. Provisioned P32E1DS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-74

Figure 107-6. Deprovision P32E1DS Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-75

Figure 107-7. Deprovisioned P32E1DS1 Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-76

Figure 107-8. Resource List Area: P2E3DS3 Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-77

Figure 107-9. Provisioned P2E3DS3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-78

Figure 107-10.Deprovision P2E3DS3 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-79

Figure 107-11.Deprovisioned P2E3DS3 Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-80

Figure 108-1. 9500 MPR Equipment Tab: CSM Card Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-82

Figure 108-2. CSM Ethernet Physical Interface: Settings Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-83

Figure 108-3. 9500 MPR Equipment Tab: CSM Card Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-84

Figure 108-4. CSM Ethernet Physical Interface: SFP Settings Tab . . . . . . . . . . . . . . . . . . . . . . . . . . 4-85

Figure 109-1. MOD300 Direction and Channel Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-87

Figure 109-2. Provision Radio Channel Fixed Modulation Parameters . . . . . . . . . . . . . . . . . . . . . . . 4-88

Figure 109-3. Provision Radio Channel Adaptive Modulation Parameters . . . . . . . . . . . . . . . . . . . . 4-90

Figure 109-4. MOD300 Radio Settings Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-91

Figure 109-5. MOD300 Radio Protection Provisioned . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-92

Figure 110-1. Synchronization Settings Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-93

Figure 110-2. Synchronization - Master / Revertive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-95

Figure 110-3. Synchronization - Slave / Revertive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-97

Figure 112-1. Ranging Sequential Flow IDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-102

Figure 112-2. Ranging Non-Sequential Flow IDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-102

Figure 112-3. Cross Connection: Line Color Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-105

Page 11: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 11/314

3EM23954ABIssue 01, February 2010

List of Figures ix

Figure 112-4. Configuration Cross Connection Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-106

Figure 112-5. PDH-RADIO Cross Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-108

Figure 112-6. PDH to Ethernet Cross Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-110

Figure 112-7. Ethernet to Radio Cross Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-111

Figure 112-8. Radio to Radio Cross Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-113

Figure 113-1. View NE Alarms Path. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-116

Figure 113-2.  Alarm Monitor Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-116

Figure 113-3.  Alarm Manager: Current Alarms Major Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-117

Figure 114-1.  Abnormal Condition List Path. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-119

Figure 114-2.  Abnormal Condition List Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-120

Figure 115-1. Protection Schemes Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-121

Figure 115-2. Protection Schemes Resource Tree Expanded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-122

Figure 115-3. CSM Protection Scheme Parameter Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-123

Figure 115-4. Synchronization Protection Scheme Parameter Tab . . . . . . . . . . . . . . . . . . . . . . . . . 4-124

Figure 115-5. Radio Channel Protection Scheme Parameter Tab . . . . . . . . . . . . . . . . . . . . . . . . . . 4-125

Figure 115-6. Equipment Protection Scheme Parameter Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-126

Figure 115-7. HSB Protection Scheme Parameter Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-127

Figure 115-8. Rx Radio Protection Scheme Parameter Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-128

Figure 116-1. Diagnosis / Current Configuration View Path. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-129

Figure 116-2. Diagnosis / Current Configuration View Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-130

Figure 116-3. Provision Verification: Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-131

Figure 116-4. Provision Verification: Login Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-131

Figure 116-5. 9500MPR Web Server Main Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-132

Figure 116-6. Configuration Info File Download Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-133

Page 12: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 12/314

Page 13: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 13/314

3EM23954ABIssue 01, February 2010

List of Figures xi

Figure 121-7. Lockout Equipment Switch: Lockout Switch to Spare . . . . . . . . . . . . . . . . . . . . . . . . 4-170

Figure 121-8. Forced HSB Switch Main Radio Channel to Spare Radio Channel . . . . . . . . . . . . . . 4-171

Figure 121-9. Manual HSB Switch: Main Radio Channel to Spare Radio Channel . . . . . . . . . . . . . 4-172

Figure 121-10.Manual HSB Switch: Spare Radio Channel to Main Radio Channel . . . . . . . . . . . . . 4-173

Figure 121-11.Lockout HSB Switch: Lockout Spare Radio Channel. . . . . . . . . . . . . . . . . . . . . . . . . 4-174

Figure 121-12.Forced Rx Radio Switch: Main Radio Channel to Spare Radio Channel. . . . . . . . . .4-175

Figure 121-13.Manual Rx Radio Switch: Main Radio Channel to Spare Radio Channel . . . . . . . . . 4-176

Figure 121-14.Manual Rx Radio Switch: Spare Radio Channel to Main Radio Channel . . . . . . . . . 4-177

Figure 121-15.Lockout Rx Radio Switch Spare Radio Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-178

Figure 122-1. 9500 MPR Equipment Tab: MOD300 Card Selected. . . . . . . . . . . . . . . . . . . . . . . . . 4-181

Figure 122-2. Performance Monitoring Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-182

Figure 122-3. Threshold Data Creation Pane. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-183

Figure 122-4. Threshold #2 Data Table Created . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-184

Figure 122-5. Threshold Data Table Selected for Modification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-185

Figure 122-6. Threshold Data Table Modified . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-186

Figure 122-7. Threshold Data Table Selected for Deletion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-187

Figure 122-8. Threshold Data Table Deleted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-188

Figure 122-9. PM HOP - Channel #0 Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-189

Figure 122-10.PM HOP-Channel #0 Current Data 15 Minute Selected . . . . . . . . . . . . . . . . . . . . . . 4-190

Figure 122-11.PM Data HOP-Channel #0 Current Data 15 Minute Selected . . . . . . . . . . . . . . . . . . 4-191

Figure 122-12.PM Data HOP-Channel #1 History Data 15 Minute Selected . . . . . . . . . . . . . . . . . . 4-192

Figure 122-13.PM Data HOP-Channel #1 History Data 15 Minute Selected . . . . . . . . . . . . . . . . . . 4-193

Figure 123-1. Main Equipment Window: MOD300 Card Highlighted . . . . . . . . . . . . . . . . . . . . . . . . 4-195

Figure 123-2. Radio Power Measurement Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-196

Page 14: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 14/314

3EM23954ABIssue 01, February 2010

List of Figuresxii

Figure 123-3. Radio Power Measurement: Graphical View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-197

Figure 123-4. Radio Power Measurement: Tabular View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-198

Figure 126-1. Cross Connection Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-199

Figure 126-2. PDH-RADIO Cross Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-200

Figure 126-3. PDH to Ethernet Cross Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-201

Figure 126-4. Ethernet to Radio Cross Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-202

Figure 126-5. Radio to Radio Cross Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-203

Figure 127-1. 9500 MPR Equipment Tab: CSM Card Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-206

Figure 127-2. CSM Ethernet Physical Interface: Settings Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-207

Figure 127-3. 9500 MPR Equipment Tab: CSM Card Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-208

Figure 127-4. CSM Ethernet Physical Interface: SFP Settings Tab . . . . . . . . . . . . . . . . . . . . . . . . . 4-209

Figure 128-1. NETO Overview Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-212

Figure 128-2. Network Elements List Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-212

Figure 128-3. NE List Save Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-213

Figure 128-4. Network Elements List Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-214

Figure 128-5. Network Elements List Window: Current NE Added . . . . . . . . . . . . . . . . . . . . . . . . . 4-215

Figure 128-6. Network Elements List Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-216

Figure 128-7. NETO Overview Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-217

Figure 128-8. Open Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-217

Figure 128-9. Network ElemenT List Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-218

Figure 128-10.NETO Overview Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-218

Figure 128-11.JUSM/CT 9500MPR-A Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-219

Figure 128-12.NETO Overview Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-220

Figure 128-13.Network ElemenT List Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-220

Page 15: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 15/314

3EM23954ABIssue 01, February 2010

List of Figures xiii

Figure 128-14.NETO Overview Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-221

Figure 128-15.JUSM/CT 9500MPR-A Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-222

Figure 129-1. Event Log Path. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-223

Figure 129-2. Event Log Browser Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-224

Figure 130-1. IF Cable Loopback Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-227

Figure 130-2. Main Equipment Window: MOD300 Card Highlighted . . . . . . . . . . . . . . . . . . . . . . . . 4-228

Figure 130-3. Radio Channel Settings Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-229

Figure 130-4. Transmitter TxMute Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-230

Figure 130-5. MOD300 IF Cable Loopback Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-231

Figure 130-6. MOD300 IF Cable Loopback Provisioned . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-232

Figure 130-7. MOD300 IF Cable Loopback Active. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-233

Figure 130-8. MOD300 IF Cable Loopback Active. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-234

Figure 130-9. MOD300 IF Cable Loopback Active, Not Active Selected . . . . . . . . . . . . . . . . . . . . . 4-235

Figure 130-10.MOD300 IF Cable Loopback Deactivated (Not Active) . . . . . . . . . . . . . . . . . . . . . . . 4-236

Figure 130-11.Settings Tab, Transmitter TxMute Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-237

Figure 130-12.TxMute Disabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-238

Figure 131-1. Backup MIB Management Database Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-241

Figure 131-2. Backup MIB Management Database Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-241

Figure 131-3. Restore MIB Management Database Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-242

Figure 131-4. Restore MIB Management Database Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-243

Figure 131-5.  Activate MIB Management Database Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-244

Figure 1-1. WebEML Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Figure 1-2. Main Menu Bar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Figure 1-3. Main Tool Bar Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Page 16: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 16/314

3EM23954ABIssue 01, February 2010

List of Figuresxiv

Figure 1-4. Resource Tree Area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

Figure 1-5. Resource List Area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

Figure 1-6. Resource Detail Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Figure 1-7. Severity Alarm Synthesis Area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Figure 1-8. Severity Alarm Synthesis Area: Alarm Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Figure 1-9. Domain Alarm Synthesis Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Figure 1-10. Domain Alarm Synthesis Area: Alarm Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8

Figure 1-11. Status Control Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9

Page 17: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 17/314

3EM23954ABIssue 01, February 2010

List of Tables xv

9500 MPR Operation and AdministrationList of Tables

Table 100-A. Index Task List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Table 101-A. Common User Administration Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Table 102-A. Equipment Provisioning and Deprovisioning Functions. . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Table 103-A. System Information Reports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Table 104-A. System Administration Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Table 105-A.  Auxiliary Equipment Provisioning Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Table 100-A. Default User Account Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Table 101-A. Default User Account Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

Table 112-A. Range of Flow ID’s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-101

Table 117-A. DSCP Traffic Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-136

Table 122-A. Default TCA Threshold Alarm Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-180

Table 1-A. Status Control Color Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

Page 18: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 18/314

3EM23954ABIssue 01, February 2010

List of Tablesxvi

Page 19: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 19/314

3EM23954ABIssue 01, February 2010

Introduction 1-1

Introduction

1. OVERVIEW

1.1 This user's guide provides step-by-step procedures to help users

perform tasks. Each procedure contains important introductory information

that is essential to understanding and completing the task properly.

Procedures must be started at step 1, and steps must be performed in the order

given. Failure to do so may cause unforeseen hazardous conditions.

Writing Conventions

1.2 Boldface characters indicate commands or parameters that must be

entered or keys that must be pressed. Enter input parameters exactly as shown

in the examples.

Admonishments

1.3 To avoid hazardous conditions, observe the following admonishments:

DANGER Possibility of personal injury.

CAUTION Possibility of service interruption.

WARNING Possibility of equipment damage.

Related Documentation

1.4 For additional system information, refer to the following related

documents:

9500 MPR Product Information (PN 3EM23952AB)

• 9500 MPR Installation Practices manual (PN 3EM23953AB)

• 9500 MPR Turn-Up manual (PN 3EM23955AB)

• 9500 MPR Maintenance and Trouble Clearing manual

(PN 3EM23956AB)

Page 20: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 20/314

3EM23954ABIssue 01, February 2010

Introduction1-2

Document Types

1.5 The documentation contains all instructions needed to perform a task.

This manual consists of the following types of documents:

• Task Index List (IXL)

• Nontrouble Procedure (NTP)

• Detailed Level Procedure (DLP)

Task Index List (IXL)

1.6 IXLs group procedures by function. Each IXL lists procedures

alphabetically by name and refers the user to the appropriate procedure

number.

Nontrouble Procedure (NTP)

1.7 NTPs list the major steps required to complete a task. This list may be

all an experienced user requires. For an inexperienced user, each step refers to

a DLP. The steps must be performed in the order listed.

Detailed Level Procedure (DLP)

1.8 DLPs contain detailed steps and supporting information required tocomplete a task. When a DLP is referenced from another part of the manual,

perform the DLP, then return to the point where the DLP was referenced.

Page 21: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 21/314

3EM23954ABIssue 01, February 2010

Introduction 1-3

2. PRODUCT SUPPORT INFORMATION

Telephone Support

Customer Service Telephone Support

2.1 For telephone support for the customer services mentioned in this

Product Support Information, call the Alcatel-Lucent's customer Technical

Support Center at 1-(888) 252-2832 for details, 8:00 a.m. to 5:00 p.m., Central

Time, Monday through Friday. Ask the operator for the appropriate service to

be connected to a qualified representative or engineer.

2.2  After-hours emergency telephone support is also available by calling

the Alcatel-Lucent's customer Technical Support Center at 1-(888) 252-2832. An emergency is defined as an out-of-service, traffic-affecting problem or a

nonoperating alarm system on traffic-bearing systems.

Product Documentation and Training

Product Documentation

2.3 Product documentation is available on both paper and CD-ROM. The

documentation can also be accessed through Alcatel-Lucent’s OnLine

Customer Support web site at:

https://support.alcatel-lucent.com/portal/olcsHome.do

Product documentation updates appear on Alcatel-Lucent’s OnLine Customer

Support web site before they are available in any other format.

Page 22: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 22/314

3EM23954ABIssue 01, February 2010

Introduction1-4

2.4  At Alcatel-Lucent’s OnLine Customer Support web site, follow the on-

screen instructions to register for access and obtain a login ID. In addition to

accessing product documentation, the Alcatel-Lucent’s OnLine Customer

Support web site allows the user to view the following:

•  Application notes

• Configuration notes

• Data collections

• Frequently Asked Questions (FAQs)

• General information books

• General Release Documents (GRDs)

• Installation documents

• Methods of Procedure (MOPs)

• Product Change Notifications (PCNs)

• Product Information Bulletins (PIBs)

• Product manual updates

• Software patch and software load documents

• Software Update Documents (SUDs)

• Technical bulletins

• Training documents

• Urgent Product Warnings (UPWs)

Training

2.5 Equipment training is available to all customers. Crafts and

maintenance personnel who are trained by Alcatel-Lucent's Training

department can expect more effective assistance if they need to call theTechnical Assistance Center. Regularly scheduled courses are available at the

training facilities in Plano, Texas. If a customer cannot attend a standard

course, the Training department can arrange a course for a specific

requirement and conduct it at the customer's facility. For further information,

call customer service telephone support and ask for a training coordinator or

write to one of the following addresses:

Page 23: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 23/314

3EM23954ABIssue 01, February 2010

Introduction 1-5

2.6 The annual Product Training Catalog can be ordered by calling the

training coordinator, or it can be viewed on-line at:

http://www1.alcatel-lucent.com/us/product_training/catalog 

Technical Support Center 

2.7 The Technical Support Center (TSC) staff is always ready to provide

high-quality technical assistance. Customers can expect effective telephoneassistance when their crafts and maintenance personnel have been trained by

 Alcatel-Lucent's Training department and are equipped with adequate test

equipment, spares, and documentation at the site.

2.8 For technical assistance, call Alcatel-Lucent's customer Technical

Support Center at 1-(888) 252-2832.

After-hours Emergency Telephone Support

2.9 Emergency support is available after-hours for emergencies by calling

1-(888) 252-2832.

2.10  An emergency is defined as an out-of-service, traffic-affecting problem

or a nonoperating alarm system on traffic-bearing systems.

2.11 Nonemergency is defined as installation turn-ups, application

questions, traffic cutover, routine maintenance, or other non-service-affecting

maintenance. All non-service-affecting, after-hours telephone services are

billable to the customer.

2.12 Please provide the operator with the following information:

• Company name

• Caller name

•  A telephone number where caller can be reached

•  A brief description of the problem, including the product involved

IN USA: IN CANADA:

 Alcatel-Lucent USA

3400 W. Plano Pkwy.

Plano, Texas 75075

 ATTN: Training M/S 1206-553

 Alcatel-Lucent Canada

Network Services Division

P.O. Box 13600

Ottawa, Ontario K2K 2E6

Page 24: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 24/314

3EM23954ABIssue 01, February 2010

Introduction1-6

After-hours Nonemergency Telephone Support

2.13  After-hours telephone support to address new installations, system

expansions, system operations, system application, or other

non-service-affecting issues is available by contacting Alcatel-Lucent at1-(888) 252-2832.

On-site Technical Support

2.14 On-site technical support is available when an issue cannot be

resolved remotely. This determination is usually made by Alcatel-Lucent TSC

during the problem investigation process. These services may or may not be

billable to a customer. This depends on several factors such as what type of

Service Level Agreement a customer has with Alcatel-Lucent, the age of the

product, etc.

Repair and Return Services

2.15  As part of a comprehensive technical support program, Alcatel-Lucent

provides factory repair services for equipment. This service is available both

during and after the warranty period through Alcatel-Lucent's Return and

Repair department.

Spare Parts and Replacement Cards

2.16 For spare parts, spare cards, card exchange, and in-warranty

replacement on a routine or emergency basis, call customer service telephone

support.

2.17 Provide the following information:

• Customer Contact Name

• Customer Company Name

• Customer telephone number

• Customer E-mail Address

•  A brief description of the problem, including product line, part

number, and quantity of parts needed

Page 25: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 25/314

3EM23954ABIssue 01, February 2010

Introduction 1-7

2.18 For emergency assistance after normal business hours, call customer

service telephone support, ask the operator for Emergency Parts Assistance,

and provide the operator with the required information. The operator will

contact an appropriate individual to respond.

Return for Credit or Warranty Exchange Procedure

2.19 Returned equipment must have a Parts Request (PR) number. Obtain

an PR number by calling the Alcatel-Lucent Welcome Center at

1-866-582-3688.

2.20 No equipment should be returned without an PR number. The

following information is required:

• Description and quantity of equipment to be returned

• Reason for return

• Order number the equipment was purchased against and approximate

date of purchase

Service Center 

2.21 The Service Center tests, repairs, and modifies all cards (both in and

out of warranty). Cards received for repair or modification are returned

promptly.

Page 26: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 26/314

3EM23954ABIssue 01, February 2010

Introduction1-8

Return for Repair Procedure

2.22 Refer to paragraph 2.19 for information on obtaining an PR number.

Notification to the Service Center and issuance of an PR number by

 Alcatel-Lucent personnel must be made prior to shipment of parts. Thefollowing information must be furnished with the request for return

authorization:

• Purchase order number or requisition number

• Description and quantity of equipment to be returned

• Reason for return:

 – Modification required

 – Defective equipment to be repaired

• Warranty status (in or out of warranty) and warranty date stamped on

unit

• Specific nature of problem

• Name and telephone number of person who identified problem

• Special instruction/information

Page 27: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 27/314

3EM23954ABIssue 01, February 2010

Introduction 1-9

Shipping Instructions for Repair, Credit, or

Warranty Exchange

2.23 Return equipment or parts prepaid to the address provided below. The

PR number must be prominently marked on the shipping label, the packinglist, and any correspondence regarding the order.

• Include company name, address, and name of person to contact in case

of a question.

• Include specific reason for return. (This aids prompt processing.)

• Include the same requisition number or purchase order number that

was furnished with request for return authorization.

• Include type number and part number of unit.

• State whether equipment is in or out of warranty.

• Furnish shipping address for return of unit, if applicable, or other

pertinent details.

• Mail purchase order, if applicable, to address shown under Return for

Repair Procedure, Attention: Service Center.

Installation and Maintenance Services

Engineering and Installation Service

2.24 Whether installation for specific equipment or a full turnkey networkfacility is needed, Installation Service can help. Alcatel-Lucent has experience

in central office, outside plant, and customer premises applications, and

specializes in flexible scheduling and high-quality service. Qualified staff are

in place nationwide, so an installation can be started and completed promptly.

Alcatel Lucent Return Equipment

Address

 Alcatel Lucent c/o UPS-SCS Attn: Repair FE

2240 Outer Loop

Bldg 5 Door 505

Louisville, Ky 40219

Page 28: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 28/314

3EM23954ABIssue 01, February 2010

Introduction1-10

Contract Maintenance Service

2.25 Field service from Alcatel-Lucent US and Canada offices are available.

 Alcatel-Lucent field service is well-suited for private networks of any size.

2.26 Factory-trained service technicians are qualified on similar systems

before they are allowed to maintain customer equipment. They have direct

access to additional technical support around the clock and to all necessary

tools and test equipment.

Page 29: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 29/314

3EM23954ABIssue 01, February 2010

Index Task List 2-1

IXL-100

IndexTask Lists(IXLs)

IXL-100

Index Task List

Refer to table 100-A  to select the type of procedure or information needed to perform tasks on the

system.

Table 100-A. Index Task List

TYPE OF PROCEDURE/INFORMATION REFERENCE

Equipment Functions IXL-105

Equipment Provisioning and Deprovisioning IXL-102

System Administration IXL-104

System Information Reports IXL-103

User Administration IXL-101

Page 30: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 30/314

3EM23954ABIssue 01, February 2010

Index Task List2-2

IXL-100

Page 31: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 31/314

3EM23954ABIssue 01, February 2010

User Administration 2-3

IXL-101

IXL-101

User Administration

Refer to table 101-A  to identify a common user administration function and the corresponding

procedure.

Table 101-A. Common User Administration Functions

FUNCTION REFERENCE

 Add New User  DLP-101

 Administer NE Lists DLP-128

 Add NE to List DLP-128

Change a User’s Password DLP-101

Change Password DLP-103

Configure PC Network Card to Connect to NE DLP-102Configure Windows Firewall DLP-132

Create NE List DLP-128

Delete User  DLP-101

Install/Upgrade JAVA JRE Software DLP-132

Install WebEML (JUSM/CT) Software DLP-132

Log Into System DLP-100

Log into NE From NE List DLP-128

Log Out of System DLP-100

Verify JAVA JRE Software Version DLP-132

Page 32: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 32/314

3EM23954ABIssue 01, February 2010

User Administration2-4

IXL-101

Page 33: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 33/314

3EM23954ABIssue 01, February 2010

Equipment Provisioning and Deprovisioning 2-5

IXL-102

IXL-102

Equipment Provisioning and Deprovisioning

Refer to table 102-A  to identify an equipment provisioning or deprovisioning function and the

corresponding procedure.

Table 102-A. Equipment Provisioning and Deprovisioning Functions

FUNCTION REFERENCE

Deprovision Cross Connections DLP-126

Deprovision Ethernet Ports DLP-127

Deprovision Equipment Ports DLP-107

Disable Equipment DLP-105

Enable Equipment DLP-104

Provision Cross Connections DLP-112Provision Ethernet Ports DLP-108

Provision Equipment Ports DLP-106

Provision Radio Parameters DLP-109

Provision Synchronization DLP-110

Page 34: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 34/314

3EM23954ABIssue 01, February 2010

Equipment Provisioning and Deprovisioning2-6

IXL-102

Page 35: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 35/314

3EM23954ABIssue 01, February 2010

System Information Reports 2-7

IXL-103

IXL-103

System Information Reports

Refer to table 103-A  to identify a system information report and the corresponding procedure for

retrieval of the report.

Table 103-A. System Information Reports

REPORT REFERENCE

View Abnormal Condition List DLP-114

View Alarms DLP-113

View Event Log DLP-129

View Protection Schemes DLP-115

Page 36: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 36/314

3EM23954ABIssue 01, February 2010

System Information Reports2-8

IXL-103

Page 37: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 37/314

3EM23954ABIssue 01, February 2010

System Administration 2-9

IXL-104

IXL-104

System Administration

Refer to table 104-A  to identify a system administration function and the corresponding procedure.

Table 104-A. System Administration Functions

FUNCTION REFERENCE

 Administer Network Configuration DLP-118

 Administer Software License DLP-120

 Administer System Date and Time DLP-119

 Administer System Settings DLP-117

 Administer TMN Ethernet Interface DLP-118

Download Provisioning Data DLP-116

MIB Database Management (Backup and Restore) DLP-131Provision IP Address of NE DLP-118

Provision IP Static Routing DLP-118

Provision OSPF Area Configuration DLP-118

Page 38: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 38/314

3EM23954ABIssue 01, February 2010

System Administration2-10

IXL-104

Page 39: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 39/314

3EM23954ABIssue 01, February 2010

Equipment Functions 2-11

IXL-105

IXL-105

Equipment Functions

Refer to table 105-A  to identify an equipment function and the corresponding procedure.

Table 105-A. Auxiliary Equipment Provisioning Functions

FUNCTION REFERENCE

IF Cable Loopback DLP-130

Performance Monitoring DLP-122

Perform Protection Switching DLP-121

Perform Radio Power Measurements DLP-123

Page 40: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 40/314

3EM23954ABIssue 01, February 2010

Equipment Functions2-12

IXL-105

Page 41: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 41/314

3EM23954ABIssue 01, February 2010

DS1 Provisioning 3-1

NTP-100

Non-trouble Procedures (NTPs)

NTP-100

DS1 Provisioning

PURPOSE

This procedure provides instructions and sequence for provisioning DS1 facilities and equipment.

GENERAL

Three procedures are provided to provision DS1 facilities and equipment as follows:

•   Provision DS1 Cross-Connect to existing DS1 port

•   Provision DS1 Cross-Connect to new DS1 port

•   Provision DS1 Cross-Connect to new DS1 P32E1DS1 card

STEP PROCEDURE

1 Select action?

To provision DS1 cross-connect to existing DS1 port, go to step 2.

To provision DS1 cross-connect to new DS1 port, go to step 3.

To provision DS1 Cross-Connect to new DS1 P32E1DS1 card, go to

step 4.

2 Provision DS1 cross-connect to existing DS1 port:

a. Refer to DLP-112 to provision DS1 Cross-Connect.

b. Go to step 5.

3 Provision DS1 cross-connect to new DS1 port:

a. Refer to DLP-106 to provision DS1 ports.

b. Refer to DLP-112 to provision DS1 Cross-Connect.

c. Go to step 5.

Page 42: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 42/314

3EM23954ABIssue 01, February 2010

DS1 Provisioning3-2

NTP-100

4 Provision DS1 Cross-Connect to new DS1 P32E1DS1 card:

a. Refer to DLP-104 to enable P32E1DS1 Card.

b. Refer to DLP-106 to provision DS1 ports.

c. Refer to DLP-112 to provision DS1 Cross-Connect.

5 STOP. This procedure is complete.

Page 43: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 43/314

3EM23954ABIssue 01, February 2010

DS3 Provisioning 3-3

NTP-101

NTP-101

DS3 Provisioning

PURPOSE

This procedure provides instructions and sequence for provisioning DS3 facilities and equipment.

GENERAL

Three procedures are provided to provision DS3 facilities and equipment as follows:

•   Provision DS3 Cross-Connect to existing DS3 port

•   Provision DS3 Cross-Connect to new DS3 port

•   Provision DS3 Cross-Connect to new DS3 P2E3DS3 card

STEP PROCEDURE

1 Select action?

To provision DS3 cross-connect to existing DS3 port, go to step 2.

To provision DS3 cross-connect to new DS3 port, go to step 3.

To provision DS3 Cross-Connect to new DS3 P2E3DS3 card, go to

step 4.

2 Provision DS3 cross-connect to existing DS3 port:

a. Refer to DLP-112 to provision DS3 Cross-Connect.

b. Go to step 5.

3 Provision DS3 cross-connect to new DS3 port:

a. Refer to DLP-106 to provision DS3 ports.

b. Refer to DLP-112 to provision DS3 Cross-Connect.

c. Go to step 5.

Page 44: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 44/314

3EM23954ABIssue 01, February 2010

DS3 Provisioning3-4

NTP-101

4 Provision DS3 Cross-Connect to new DS3 P2E3DS3 card:

a. Refer to DLP-104 to enable P2E3DS3 Card.

b. Refer to DLP-106 to provision DS3 ports.

c. Refer to DLP-112 to provision DS3 Cross-Connect.

5 STOP. This procedure is complete.

Page 45: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 45/314

3EM23954ABIssue 01, February 2010

Ethernet Provisioning 3-5

NTP-102

NTP-102

Ethernet Provisioning

PURPOSE

This procedure provides instructions and sequence for provisioning Ethernet facilities and

equipment.

GENERAL

Four procedures are provided to provision Ethernet facilities and equipment as follows:

•   Provision Ethernet Cross-Connect to existing CSM Ethernet port

•   Provision Ethernet Cross-Connect to new CSM Ethernet port

  Provision Ethernet Cross-Connect to new CSM SFP equipment port

•   Provision Ethernet Cross-Connect to new CSM card

STEP PROCEDURE

1 Select action?

To provision Ethernet cross-connect to existing CSM Ethernet port, go

to step 2.

To provision Ethernet cross-connect to new CSM Ethernet port, go to

step 3.To provision Ethernet cross-connect to new CSM SFP equipment port,

go to step 4.

To provision Ethernet Cross-Connect to new CSM card, go to step 5.

2 Provision Ethernet cross-connect to existing CSM Ethernet port:

a. Refer to DLP-112 to provision Ethernet Cross-Connect.

b. Go to step 6.

3 Provision Ethernet cross-connect to new CSM Ethernet port:

a. Refer to DLP-108 to provision CSM Ethernet port.

b. Refer to DLP-112 to provision Ethernet Cross-Connect.

c. Go to step 6.

Page 46: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 46/314

3EM23954ABIssue 01, February 2010

Ethernet Provisioning3-6

NTP-102

4 Provision Ethernet cross-connect to new CSM SFP equipment port:

a. Refer to DLP-106 to provision CSM SFP equipment port.

b. Refer to DLP-108 to provision CSM Ethernet port.

c. Refer to DLP-112 to provision Ethernet Cross-Connect.

d. Go to step 6.

5 Provision Ethernet Cross-Connect to new protect CSM card:

a. Refer to DLP-104 to enable protect CSM Card.

b. Refer to DLP-106 to provision CSM SFP equipment port.

c. Refer to DLP-108 to provision CSM Ethernet port.

d. Refer to DLP-112 to provision Ethernet Cross-Connect.

6 STOP. This procedure is complete.

Page 47: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 47/314

3EM23954ABIssue 01, February 2010

DS1 Deprovisioning 3-7

NTP-103

NTP-103

DS1 Deprovisioning

PURPOSE

This procedure provides instructions and sequence for deprovisioning DS1 facilities and equipment.

GENERAL

Three procedures are provided to deprovision DS1 facilities and equipment as follows:

•   Deprovision DS1 Cross-Connect

•   Deprovision DS1 port

•   Deprovision DS1 P32E1DS1 card

STEP PROCEDURE

1 Select action?

If deprovisioning DS1 cross-connect, go to step 2.

If deprovisioning DS1 port, go to step 3.

If deprovisioning DS1 P32E1DS1 card, go to step 4.

2 Deprovision DS1 cross-connect:

a. Refer to DLP-126 to deprovision DS1 cross-connect.

b. Go to step 5.

3 Deprovision DS1 port:

a. Refer to DLP-126 to deprovision DS1 Cross-Connects associated with P32E1DS1

port.

b. Refer to DLP-107 to deprovision DS1 port.

c. Go to step 5.

Page 48: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 48/314

3EM23954ABIssue 01, February 2010

DS1 Deprovisioning3-8

NTP-103

4 Deprovision DS1 P32E1DS1 card:

a. Refer to DLP-126 to deprovision DS1 Cross-Connects associated with P32E1DS1

card.

b. Refer to DLP-107 to deprovision DS1 ports associated with P32E1DS1 card.

c. Refer to DLP-105 to disable P32E1DS1 card.

5 STOP. This procedure is complete.

Page 49: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 49/314

3EM23954ABIssue 01, February 2010

DS3 Deprovisioning 3-9

NTP-104

NTP-104

DS3 Deprovisioning

PURPOSE

This procedure provides instructions and sequence for deprovisioning DS3 facilities and equipment.

GENERAL

Three procedures are provided to deprovision DS3 facilities as follows:

•   Deprovision DS3 Cross-Connect

•   Deprovision DS3 port

•   Deprovision DS3 P2E3DS3 card

STEP PROCEDURE

1 Select action?

If deprovisioning DS3 Cross-Connect, go to step 2.

If deprovisioning DS3 port, go to step 3.

If deprovisioning DS3 P2E3DS3 card, go to step 4.

2 Deprovision DS3 cross-connect:

a. Refer to DLP-126 to deprovision DS3 Cross-Connect.

b. Go to step 5.

3 Deprovision DS3 port:

a. Refer to DLP-126 to deprovision DS3 Cross-Connect associated with DS3 port.

b. Refer to DLP-107 to deprovision DS3 port.

c. Go to step 5.

Page 50: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 50/314

3EM23954ABIssue 01, February 2010

DS3 Deprovisioning3-10

NTP-104

4 Deprovision DS3 P2E3DS3 card:

a. Refer to DLP-126 to deprovision DS3 Cross-Connects associated with P2E3DS3

card.

b. Refer to DLP-107 to deprovision DS3 ports associated with P2E3DS3 card.

c. Refer to DLP-105 to disable P2E3DS3 card.

5 STOP. This procedure is complete.

Page 51: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 51/314

3EM23954ABIssue 01, February 2010

Ethernet Deprovisioning 3-11

NTP-105

NTP-105

Ethernet Deprovisioning

PURPOSE

This procedure provides instructions and sequence for provisioning Ethernet facilities and

equipment.

GENERAL

Four procedures are provided to provision Ethernet facilities and equipment as follows:

•   Deprovision Ethernet Cross-Connect from CSM Ethernet port

•   Deprovision CSM Ethernet port

  Deprovision CSM SFP equipment port

•   Deprovision protect CSM card

STEP PROCEDURE

1 Select action?

To deprovision Ethernet cross-connect from CSM Ethernet port, go to

step 2.

To deprovision CSM Ethernet port, go to step 3.

To deprovision CSM SFP equipment port, go to step 4.To deprovision protect CSM card, go to step 5.

2 Deprovision Ethernet cross-connect from CSM Ethernet port:

a. Refer to DLP-126 to deprovision Ethernet cross-connect.

b. Go to step 6.

3 Deprovision CSM Ethernet port:

a. Refer to DLP-126 to deprovision Ethernet cross-connects associated with CSM

Ethernet port.

b. Refer to DLP-127 to deprovision CSM Ethernet port.

c. Go to step 6.

Page 52: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 52/314

3EM23954ABIssue 01, February 2010

Ethernet Deprovisioning3-12

NTP-105

4 Deprovision CSM SFP equipment port:

a. Refer to DLP-126 to deprovision Ethernet cross-connects associated with CSM

Ethernet port.

b. Refer to DLP-127 to deprovision CSM Ethernet port.

c. Refer to DLP-107 to deprovision CSM SFP equipment port.

d. Go to step 6.

5 Deprovision protect CSM card:

a. Refer to DLP-126 to deprovision Ethernet cross-connects associated with CSM

Ethernet port.

b. Refer to DLP-127 to deprovision CSM Ethernet ports associated with CSM card.

c. Refer to DLP-107 to deprovision CSM SFP equipment port.

d. Refer to DLP-105 to disable protect CSM Card.

6 STOP. This procedure is complete.

Page 53: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 53/314

3EM23954ABIssue 01, February 2010

Log Into and Out of System 4-1

DLP-100

Detailed Level Procedures (DLPs)

DLP-100

Log Into and Out of System

PURPOSE

This procedure provides the instructions to establish a session with the network element (NE) and

to log in and to log out a specific user to the 9500 MPR.

PREREQUISITE

The Username and current Password must be known before login can be accomplished. 9500 MPR-A

CT R01.02 - Craft Terminal (CT) software must be installed on the PC. The user must know the IP

address of the NE to log into the system or be locally connected.

GENERAL

The 9500 MPR provides support for the Craft Terminal (CT) or WebEML (JUSM/CT) function,allowing NE management through a web-enabled PC.

The NE is accessed using the Network ElemenT Overview (NETO) application.

Four user profiles are available (Administrator, CraftPerson, Operator, and Viewer). Refer to

DLP-101 for definitions of each user profile responsibilities.

Two default user accounts are available on the NE with the profiles as follows:

The WebEML Craft Terminal Reference Guide in the back of this manual may also be used as

reference.

STEP PROCEDURE

1 Select action?

If log into JUSM/CT 9500MPR-A, go to step 2.

If log out of JUSM/CT 9500MPR-A, go to step 11.

Table 100-A. Default User Account Profiles

Username Password Profile

initial adminadmin administrator  

Craftperson craftcraft Craft Person

Page 54: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 54/314

3EM23954ABIssue 01, February 2010

Log Into and Out of System4-2

DLP-100

Log Into System

2 Is NETO currently running?

If no, go to step 3.

If yes, go to step 4.

3 Double click the MPRA_CT icon on the desktop to launch NETO. See Figure 100-1.

NETO window opens. See Figure 100-2.

4 From the NETO window, enter the NE IP Address or DNS name 

5 Click OK.

Figure 100-1. MPR-A R01.02 WebEML Icon

Figure 100-2. NETO Overview Window

Page 55: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 55/314

3EM23954ABIssue 01, February 2010

Log Into and Out of System 4-3

DLP-100

6 Click Show to launch radio application software.

“WebEML JUSM.” window opens.

7 Click OK.

The “WebEML JUSM.” window closes automatically, even if OK is not clicked.

The Login window opens. See Figure 100-3.

8 In the Login window, enter UserName “username” and Password “ password”.

9 Click Apply.

JUSM 9500MPR window launches. See Figure 100-4.

Figure 100-3. NETO Login Window

Page 56: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 56/314

3EM23954ABIssue 01, February 2010

Log Into and Out of System4-4

DLP-100

10 Go to step 16.

Log Out of System

11 In the upper right hand corner of the JUSM/CT window, select the “ X” . See

Figure 100-5.

The confirm request window opens.

12 Click Yes.

Figure 100-4. JUSM/CT 9500MPR-A Main Screen

Page 57: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 57/314

3EM23954ABIssue 01, February 2010

Log Into and Out of System 4-5

DLP-100

13 Close NETO application?

If yes, go to step 14.

If no, go to step 16.

14 Click Exit. See Figure 100-6.

The confirm request window opens.

15 Click Yes.

Figure 100-5. JUSM/CT 9500MPR-A Main Screen

Page 58: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 58/314

3EM23954ABIssue 01, February 2010

Log Into and Out of System4-6

DLP-100

16 STOP. This procedure is complete.

Figure 100-6. NETO Overview Window

Page 59: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 59/314

3EM23954ABIssue 01, February 2010

 Administer User Profiles 4-7

DLP-101

DLP-101

Administer User Profiles

PURPOSE

This procedure provides the instructions to Create, Delete, and Change Password of a system user

for a specified UserName.

GENERAL

Only a user with system administrator privileges can create, delete and change another user’s

password.

The system allows up to 10 management users and 23 provisioned users.

There are four user profile classes. The responsibilities are as follows:

•   Administrator - Full access including security parameters

•   CraftPerson - Local access to radio without security parameters at the radio site.

Typical user is responsible for installation and maintenance at the radio site.

•   Operator - Remote access to radio without security parameters. Typical user is

responsible for operation at the network level and not at the radio site.

•   Viewer - Only view access allowed.

User Name length must not exceed 20 characters.

Passwords must meet the following complexity parameters:

•   Minimum Length - Password must be at least eight characters in length

•   Maximum Length - Password shall not exceed twenty characters in length

•   Composition - Passwords must be composed of full ASCII characters (UPPER

case, lower case, numeric, and special characters).

Two default user accounts are available on the NE. These default user accounts can not be deleted.

For security reasons the password for the default user accounts should be changed. Refer to

Table 101-A  for default user account details.

Table 101-A. Default User Account Profiles

User Name Password Profile

initial adminadmin administrator  

Craftperson craftcraft CraftPerson

Page 60: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 60/314

3EM23954ABIssue 01, February 2010

 Administer User Profiles4-8

DLP-101

The WebEML Craft Terminal Reference Guide in the back of this manual may also be used as

reference.

STEP PROCEDURE

1 Select action.

To add new user, go to step 2.

To delete user, go to step 13.

To change a user’s password, go to step 22.

Add New User 

2 Select Configuration/Profiles Management/Users Management.

The Profiles Management window opens.

Figure 101-1. User Management Drop-Down Menu

Figure 101-2. Profile Management Window

Page 61: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 61/314

3EM23954ABIssue 01, February 2010

 Administer User Profiles 4-9

DLP-101

3 Click Create.

The Create User window opens.

4 Enter the Admin Password “ AdminPassword”

5 Enter the new User Name “UserName”

6 Select user Profile class from the drop-down menu “ Administrator, CraftPerson,

Operator, or Viewer.

7 Enter the new user Password “NewUserPassword”.

8 Enter the Confirm Password “NewUserPassword”.

9 Click Apply.

User Creation Success window opens.

10 Click OK.

User Creation Success window closes.

Profile Management window opens with new user added.

Figure 101-3. Create User Window

Page 62: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 62/314

3EM23954ABIssue 01, February 2010

 Administer User Profiles4-10

DLP-101

11 Click Cancel.

12 Go to step 31.

Delete User 

13 Select Configuration/Profiles Management/Users Management.

The Profiles Management window opens.

Figure 101-4. Profile Management Window - with Added User 

Figure 101-5. User Management Drop-Down Menu

Page 63: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 63/314

3EM23954ABIssue 01, February 2010

 Administer User Profiles 4-11

DLP-101

14 Select User Name to delete.

15 Click Delete.

The Deletion Confirm window opens.

16 Click Yes.

The Delete User window opens.

17 Enter the Admin Password “ AdminPassword”

18 Click Apply.

User Deletion Success window opens.

Figure 101-6. Profile Management Window

Figure 101-7. Delete User Window

Page 64: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 64/314

3EM23954ABIssue 01, February 2010

 Administer User Profiles4-12

DLP-101

19 Click OK.

The Delete User window closes.

Profile Management window opens with user deleted.

20 Click Cancel.

21 Go to step 31.

Change a User’s Password

22 Select Configuration/Profiles Management/Users Management.

The Profiles Management window opens.

Figure 101-8. Profile Management Window - with User Deleted

Figure 101-9. User Management Drop-Down Menu

Page 65: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 65/314

3EM23954ABIssue 01, February 2010

 Administer User Profiles 4-13

DLP-101

23 Select User Name to change password.

24 Click Change PW.

The Change Password window opens.

25 Enter the Admin Password “ AdminPassword”

26 Enter the New Password “NewPassword”

27 Enter the Confirm New Password “NewPassword”.

Figure 101-10. Profile Management Window

Figure 101-11. Change User Password Window

Page 66: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 66/314

3EM23954ABIssue 01, February 2010

 Administer User Profiles4-14

DLP-101

28 Click Apply.

Changing Password Success window opens.

29 Click OK.

30 Click Cancel.

31 STOP. This procedure is complete.

Page 67: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 67/314

3EM23954ABIssue 01, February 2010

Configure PC Network Card to Connect to NE 4-15

DLP-102

DLP-102

Configure PC Network Card to Connect to NE

PURPOSE

This procedure provides the instructions for the user to configure a PC’s network card so it can

connect to the NE.

GENERAL

The user’s PC must be properly configured to communicate with the NE.

The user’s PC must be configured to obtain an IP address automatically, or the user must know the

configured IP address of the radio.

The WebEML Craft Terminal Reference Guide in the back of this manual may also be used as

reference.

STEP PROCEDURE

Configure PC Network Card

1 Connect a CAT 5/5E cable from the PC network card to the NMS connector on Slot 1

Core (CSM - Control and Switching Module) card.

2 Click on the START menu on the Windows desktop and open up the CONTROL PANEL.

3 Open up the NETWORK CONNECTIONS. Highlight the network card.

4 Right click and select Properties to display the network card properties screen.

5 Scroll down the list and highlight the Internet Protocol (TCP/IP) line.

6 Click Properties.

Page 68: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 68/314

3EM23954ABIssue 01, February 2010

Configure PC Network Card to Connect to NE4-16

DLP-102

Internet Protocol (TCP/IP) Properties window displays.

7 Configure PC network card to connect to NE?

If using DHCP, go to step 8.

If using specific NE IP address, go to step 11.

8 Select Obtain an IP address automatically. See Figure 102-2.

9 Click OK.

Figure 102-1. Internet Protocol (TCP/IP) Properties Window

Page 69: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 69/314

3EM23954ABIssue 01, February 2010

Configure PC Network Card to Connect to NE 4-17

DLP-102

10 Go to step 16.

11 Write down the current IP Address that is observed in the IP address field on the

Internet Protocol (TCP/IP) Properties screen for future use, and for reference for the

Network Configuration section.

12 Select Use the following IP address. See Figure 102-3.

13 Enter the <NE IP address +1> for the PC network card into the IP address field.

14 Enter the Subnet Mask for the radio interfaced into the Subnet Mask field.

15 Click OK.

NOTE: The 10.0.1.3 IP address example shown in Figure 102-3 is derived from the default NE

IP address (10.0.1.2) plus 1. If there is an IP address conflict within your network, increment

the last number by two.

Figure 102-2. Internet Protocol (TCP/IP) Properties Window Configured for DHCP

Page 70: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 70/314

3EM23954ABIssue 01, February 2010

Configure PC Network Card to Connect to NE4-18

DLP-102

16 Click OK.

17 Close the Network Connections window.

18 To check the connectivity between the PC and the NE, open up a DOS window or

Command Prompt. Click on the START menu on the Windows desktop and open up the

RUN window.

The Run window will display.

Figure 102-3. Internet Protocol (TCP/IP) Properties Window Configured

to Use a specific IP Address

Page 71: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 71/314

3EM23954ABIssue 01, February 2010

Configure PC Network Card to Connect to NE 4-19

DLP-102

19 Type cmd and click OK to open up a DOS window.

The DOS window will display.

20 In the DOS window, click the cursor after the > and type ping IP Address of Radio to

verify a connection between the PC and the NE.

NOTE: The 10.0.1.2 IP address is the default NE IP address.

The Ping statistics for the IP address 10.0.1.2 should display 4 packets sent and 4

packets received.

Figure 102-4. Run Window

Figure 102-5. DOS Command Window

Page 72: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 72/314

3EM23954ABIssue 01, February 2010

Configure PC Network Card to Connect to NE4-20

DLP-102

21 Close DOS window.

22 STOP. This procedure is complete.

Figure 102-6. Successful Ping Example

Page 73: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 73/314

3EM23954ABIssue 01, February 2010

Change Password 4-21

DLP-103

DLP-103

Change Password

PURPOSE

This procedure provides the instructions for a user to change their own password.

GENERAL

The system allows a user to change their own password. Only a user with system administrator

privileges can change another person’s user password.

Passwords must meet the following complexity parameters:

•   Minimum Length - Password must be at least eight characters in length

  Maximum Length - Password shall not exceed twenty characters in length

•   Composition - Passwords must be composed of full ASCII characters (UPPER

case, lower case, numeric, and special characters).

The WebEML Craft Terminal Reference Guide in the back of this manual may also be used as

reference.

STEP PROCEDURE

Change User Password

1 Select Configuration/Profiles Management/Change Password.

The Change Password window opens.

Figure 103-1. User Change Password Drop-Down Menu

Page 74: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 74/314

3EM23954ABIssue 01, February 2010

Change Password4-22

DLP-103

2 Enter the Old Password “OldPassword”

3 Enter the New Password “NewPassword”

4 Enter the Confirm New Password “NewPassword”.

5 Click Apply.

Changing Password Success window opens.

6 Click OK.

7 STOP. This procedure is complete.

Figure 103-2. Changing Password Window

Page 75: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 75/314

3EM23954ABIssue 01, February 2010

Enable Equipment 4-23

DLP-104

DLP-104

Enable Equipment

PURPOSE

This procedure provides instructions to enable cards in the system.

PREREQUISITES

GENERAL

The ODU is enabled automatically when the MOD300 is enabled.

The WebEML Craft Terminal Reference Guide in the back of this manual may also be used as

reference.

STEP PROCEDURE

Enable Cards

1 Select action.

To enable protect CSM card, go to step 2.

To enable FAN card, go to step 7.

To enable MOD300 card, go to step 12.

To enable P32E1DS1 card, go to step 17.

To enable P2E3DS3 card, go to step 22.

Enable Protect CSM Card

2 Select the MSS-8/Slot#2 in the Resource Tree area. The selected slot will be highlighted

in yellow. This selection will also highlight slot #2 in blue on the graphical

representation of the MSS-8 shelf in the Resource List Area. See Figure 104-1.

Page 76: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 76/314

3EM23954ABIssue 01, February 2010

Enable Equipment4-24

DLP-104

3 Click on the Settings Tab in the Resource Detail Area.

4 Select the Equipment Type drop-down menu and select CORE. See Figure 104-2.

Figure 104-1. Select Slot 2 to Enable Protect CSM

Page 77: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 77/314

3EM23954ABIssue 01, February 2010

Enable Equipment 4-25

DLP-104

5 Click Apply.

The protect CSM card will populate slot #2. See Figure 104-3.

Figure 104-2. Select Protect CSM Equipment Type

Page 78: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 78/314

3EM23954ABIssue 01, February 2010

Enable Equipment4-26

DLP-104

6 Go to step 26.

Enable Fan

7 Select the MSS-8/Slot9 in the Resource Tree area where the FAN card will be enabled.

The selected slot will be highlighted in yellow. This selection will also highlight slot 9

in blue on the graphical representation of the MSS-8 shelf in the Resource List Area.

See Figure 104-4.

Figure 104-3. Protect CSM Enabled

Page 79: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 79/314

3EM23954ABIssue 01, February 2010

Enable Equipment 4-27

DLP-104

8 Click on the Settings Tab in the Resource Detail Area.

9 Select the Equipment Type drop-down menu and choose FANS. See Figure 104-5.

Figure 104-4. Select Slot 9 to Enable FAN

Page 80: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 80/314

3EM23954ABIssue 01, February 2010

Enable Equipment4-28

DLP-104

10 Click Apply.

The FAN card will populate slot #9. See Figure 104-6.

Figure 104-5. Select FAN Equipment Type

Page 81: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 81/314

3EM23954ABIssue 01, February 2010

Enable Equipment 4-29

DLP-104

11 Go to step 26.

Enable MOD300 Radio Card

12 Select the MSS-8/Slot# (slot 3 through 8) in the Resource Tree area where the

MOD300 card will be enabled. The selected slot will be highlighted in yellow. This

selection will also highlight the selected slot in blue on the graphical representation of

the MSS-8 shelf in the Resource List Area. See Figure 104-7.

Figure 104-6. FAN Enabled

Page 82: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 82/314

3EM23954ABIssue 01, February 2010

Enable Equipment4-30

DLP-104

13 Click on the Settings Tab in the Resource Detail Area.

14 Select the Equipment Type drop-down menu and choose MD300 (MOD300). See

Figure 104-8.

Figure 104-7. Select Slot to Enable MOD300

Page 83: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 83/314

3EM23954ABIssue 01, February 2010

Enable Equipment 4-31

DLP-104

15 Click Apply.

The MOD300 card will populate selected slot #. See Figure 104-9.

Figure 104-8. Select MD300 Equipment Type

Page 84: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 84/314

3EM23954ABIssue 01, February 2010

Enable Equipment4-32

DLP-104

16 Go to step 26.

Enable DS1 P32E1DS1 Card

17 Select the MSS-8/Slot# (slot 3 through 8) in the Resource Tree area where the

P32E1DS1 card will be enabled. The selected slot will be highlighted in yellow. This

selection will also highlight the selected slot in blue on the graphical representation of

the MSS-8 shelf in the Resource List Area. See Figure 104-10.

Figure 104-9. MOD300 Enabled

Page 85: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 85/314

3EM23954ABIssue 01, February 2010

Enable Equipment 4-33

DLP-104

18 Click on the Settings Tab in the Resource Detail Area.

19 Select the Equipment Type drop-down menu and select P32E1DS1. See Figure 104-11.

Figure 104-10. Select Slot to Enable P32E1DS1

Page 86: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 86/314

3EM23954ABIssue 01, February 2010

Enable Equipment4-34

DLP-104

20 Click Apply.

The P32E1DS1 card will populate selected slot #. See Figure 104-12.

Figure 104-11. Select P32EDS1 Equipment Type

Page 87: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 87/314

3EM23954ABIssue 01, February 2010

Enable Equipment 4-35

DLP-104

21 Go to step 26.

Enable DS3 P2E3DS3 Card

22 Select the MSS-8/Slot# (slot 3 through 8) in the Resource Tree area where the

P2E3DS3 card will be enabled. The selected slot will be highlighted in yellow. This

selection will also highlight the selected slot in blue on the graphical representation of

the MSS-8 shelf in the Resource List Area. See Figure 104-13.

Figure 104-12. P32E1DS1 Enabled

Page 88: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 88/314

3EM23954ABIssue 01, February 2010

Enable Equipment4-36

DLP-104

23 Click on the Settings Tab in the Resource Detail Area.

24 Select the Equipment Type drop-down menu and select P2E3DS3. See Figure 104-14.

Figure 104-13. Select Slot to Enable P2E3DS3

Page 89: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 89/314

3EM23954ABIssue 01, February 2010

Enable Equipment 4-37

DLP-104

25 Click Apply.

The P2E3DS3 card will populate selected slot #. See Figure 104-15.

Figure 104-14. Select P2E3DS3 Equipment Type

Page 90: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 90/314

3EM23954ABIssue 01, February 2010

Enable Equipment4-38

DLP-104

26 STOP. This procedure is complete.

Figure 104-15. P2E3DS3 Enabled

Page 91: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 91/314

3EM23954ABIssue 01, February 2010

Disable Equipment 4-39

DLP-105

DLP-105

Disable Equipment

PURPOSE

This procedure provides instructions to Disable cards in the system.

PREREQUISITES

 Associated facilities and equipment ports must be deprovisioned before a card may be disabled.

GENERAL

The WebEML Craft Terminal Reference Guide in the back of this manual may also be used as

reference.

STEP PROCEDURE

Disable Cards

1 Select action.

To disable protect CSM card, go to step 2.

To disable FAN card, go to step 7.

To disable MOD300 card, go to step 12.

To disable ODU card, go to step 16.

To disable P32E1DS1 card, go to step 18.

To disable P2E3DS3 card, go to step 23.

Disable Protect CSM Card

2 Select the MSS-8/Slot#2 in the Resource Tree area. The selected slot will be highlighted

in yellow. This selection will also highlight spare CSM card in slot #2 in blue on the

graphical representation of the MSS-8 shelf in the Resource List Area. See

Figure 105-1.

Page 92: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 92/314

3EM23954ABIssue 01, February 2010

Disable Equipment4-40

DLP-105

3 Click on the Settings Tab in the Resource Detail Area.

4 Select the Equipment Type drop-down menu and select EMPTY. See Figure 105-2.

Figure 105-1. Enabled Spare CSM

Page 93: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 93/314

3EM23954ABIssue 01, February 2010

Disable Equipment 4-41

DLP-105

5 Click Apply.

The spare CSM card is removed from slot #2. See Figure 105-3.

NOTE: Spare CSM Card will not be disabled if the card has cross-connects and/or equipment

 ports associated.

Figure 105-2. Disable Protect CSM

Page 94: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 94/314

3EM23954ABIssue 01, February 2010

Disable Equipment4-42

DLP-105

6 Go to step 27.

Disable Fan

7 Select the MSS-8/Slot9 in the Resource Tree area where the FAN card will be disabled.

The selected slot will be highlighted in yellow. This selection will also highlight slot 9,

MSS/FANS in blue on the graphical representation of the MSS-8 shelf in the Resource

List Area. See Figure 105-4.

Figure 105-3. Protect CSM Disabled

Page 95: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 95/314

3EM23954ABIssue 01, February 2010

Disable Equipment 4-43

DLP-105

8 Click on the Settings Tab in the Resource Detail Area.

9 Select the Equipment Type drop-down menu and select EMPTY. See Figure 105-5.

Figure 105-4. Enabled FAN

Page 96: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 96/314

3EM23954ABIssue 01, February 2010

Disable Equipment4-44

DLP-105

10 Click Apply.

The FAN card is removed from slot #9. See Figure 105-6.

Figure 105-5. Disable FAN

Page 97: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 97/314

3EM23954ABIssue 01, February 2010

Disable Equipment 4-45

DLP-105

11 Go to step 27.

Disable MOD300 Radio Card

12 Select the MSS-8/Slot# (slot 3 through 8) in the Resource Tree area where the

MOD300 card is enabled. The selected slot will be highlighted in yellow. This selection

will also highlight the selected MSS/MOD300 in blue on the graphical representation

of the MSS-8 shelf in the Resource List Area. See Figure 105-7.

Figure 105-6. FAN Disabled

Page 98: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 98/314

3EM23954ABIssue 01, February 2010

Disable Equipment4-46

DLP-105

13 Click on the Settings Tab in the Resource Detail Area.

14 Select the Equipment Type drop-down menu and choose EMPTY. See Figure 105-8.

Figure 105-7. Enabled MOD300

Page 99: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 99/314

3EM23954ABIssue 01, February 2010

Disable Equipment 4-47

DLP-105

15 Click Apply.

The MOD300 card is removed from selected slot #. See Figure 105-9.

Figure 105-8. Disable MOD300

Page 100: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 100/314

3EM23954ABIssue 01, February 2010

Disable Equipment4-48

DLP-105

16 Go to step 27.

Disable ODU

NOTE: The ODU is automatically disabled when the MOD300 card is disabled.

17 Go to step 27.

Disable DS1 P32E1DS1 Card

18 Select the MSS-8/Slot# (slot 3 through 8) in the Resource Tree area where the

P32E1DS1 card will be disabled. The selected slot will be highlighted in yellow. This

selection will also highlight the selected slot in blue on the graphical representation of

the MSS-8 shelf in the Resource List Area. See Figure 105-10.

Figure 105-9. MOD300 Disabled

Page 101: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 101/314

3EM23954ABIssue 01, February 2010

Disable Equipment 4-49

DLP-105

19 Click on the Settings Tab in the Resource Detail Area.

20 Select the Equipment Type drop-down menu and select EMPTY. See Figure 105-11.

21 Click Apply.

Figure 105-10. Enabled P32E1DS1

Page 102: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 102/314

Page 103: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 103/314

3EM23954ABIssue 01, February 2010

Disable Equipment 4-51

DLP-105

22 Go to step 27.

Disable DS3 P2E3DS3 Card

23 Select the MSS-8/Slot# (slot 3 through 8) in the Resource Tree area where the

P2E3DS3 card will be disabled. The selected slot will be highlighted in yellow. This

selection will also highlight the selected slot in blue on the graphical representation of

the MSS-8 shelf in the Resource List Area. See Figure 105-13.

Figure 105-12. Disabled P32E1DS1

Page 104: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 104/314

3EM23954ABIssue 01, February 2010

Disable Equipment4-52

DLP-105

24 Click on the Settings Tab in the Resource Detail Area.

25 Select the Equipment Type drop-down menu and select EMPTY. See Figure 105-14.

Figure 105-13. Enabled P2E3DS3

Page 105: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 105/314

3EM23954ABIssue 01, February 2010

Disable Equipment 4-53

DLP-105

26 Click Apply.

The P2E3DS3 card disabled will be removed from the selected slot #. See

Figure 105-15.

NOTE: P2E3DS3 Card will not be disabled if the card has cross-connects and/or equipment

 ports associated.

Figure 105-14. Disable P2E3DS3

Page 106: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 106/314

3EM23954ABIssue 01, February 2010

Disable Equipment4-54

DLP-105

27 STOP. This procedure is complete.

Figure 105-15. Disabled P2E3DS3

Page 107: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 107/314

3EM23954ABIssue 01, February 2010

Provision Equipment Ports 4-55

DLP-106

DLP-106

Provision Equipment Ports

PURPOSE

This procedure is used to provision equipment ports.

GENERAL

While provisioning PDH circuits (DS1 or DS3) the service profile must be provisioned either

TDM2TDM or TDM2ETH.

Provision the PDH circuit TDM2TDM when both termination points of the PDH circuit are

terminated on 9500 MPR equipment.

Provision the PDH circuit TDM2ETH when one of the termination points of the PDH circuit is

terminated on non-9500 MPR equipment, and the other equipment is MEF-8 compliant.

PREREQUISITES

CSM, DS1 (P32E1DS1) or DS3 (P2E3DS3) cards must be enabled into the MSS-8 shelf slots prior to

 provisioning equipment ports.

STEP PROCEDURE

Provision Equipment Ports

1 Select action.

To provision CSM, SFP port, go to step 2.

To provision P32E1DS1, DS1 port, go to step 7.

To provision P2E3DS3, DS3 port, go to step 21.

Provision CSM SFP Port

2 Select slot #1 or #2 below the slot the MSS/CSM card is equipped in the Resource Tree

area. The selected name will highlighted in yellow.

3 Click on the Settings Tab in the Resource Detail Area. See Figure 106-1.

Page 108: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 108/314

3EM23954ABIssue 01, February 2010

Provision Equipment Ports4-56

DLP-106

4 Select Equipment Type drop-down menu, select type SFP. See Figure 106-2.

Figure 106-1. Resource List Area: CSM SFP Slot Selected

Page 109: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 109/314

3EM23954ABIssue 01, February 2010

Provision Equipment Ports 4-57

DLP-106

5 Click Apply.

The CSM SFP port will populate selected slot #. See Figure 106-3.

NOTE: CSM Ports 1-4 and port selected SFP are ready for provisioning.

Figure 106-2. Provision CSM SFP Port

Page 110: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 110/314

3EM23954ABIssue 01, February 2010

Provision Equipment Ports4-58

DLP-106

6 Go to step 36.

Provision DS1 P32E1DS1 Port

7 Double left click the DS1 (P32E1DS1) card in the Resource List Area. See

Figure 106-4.

Figure 106-3. Provisioned CSM SFP Port

Page 111: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 111/314

3EM23954ABIssue 01, February 2010

Provision Equipment Ports 4-59

DLP-106

The Alarms&Settings screen displays.

8 Select Settings tab. See Figure 106-5.

Figure 106-4. Resource List Area: P32E1DS1 Selected

Page 112: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 112/314

3EM23954ABIssue 01, February 2010

Provision Equipment Ports4-60

DLP-106

See Figure 106-6 for the following steps:

9 Select DS1 port number to provision: 01 to 32 .

10 Select the Signal Mode drop-down menu and select signal mode type: Unframed,Framed SF, or Framed ESF.

11 Select the appropriate Line Coding radio button: AMI or B8ZS.

12 Enter the Line Length (distance to cross-connect): 0  to 655 .

13 Enter the unique Flow ID number.

Figure 106-5. Provision P32E1DS1 Port

Page 113: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 113/314

3EM23954ABIssue 01, February 2010

Provision Equipment Ports 4-61

DLP-106

14 Select the Service Profile drop-down menu and select service profile type, TDM2TDM or

TDM2ETH.

15 Click Apply.

16 DS1 port service profile TDM2ETH? See Figure 106-7.

If yes, go to step 17.

If no, go to step 20.

Figure 106-6. Provisioned P32E1DS1 TDM2TDM Port

Page 114: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 114/314

3EM23954ABIssue 01, February 2010

Provision Equipment Ports4-62

DLP-106

Provision TDM2ETH Service Profile

See Figure 106-8 for the following steps:

17 Enter the unique ECID Tx  value.

18 Enter the unique ECID Rx  value.

19 Click Apply.

Figure 106-7. Provision P32E1DS1 for TDM2ETH Port

Page 115: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 115/314

3EM23954ABIssue 01, February 2010

Provision Equipment Ports 4-63

DLP-106

20 Go to step 36.

Provision DS3 P2E3DS3 Port

21 Double left click the MSS/DS3 (P2E3DS3) card in the Resource List Area. SeeFigure 106-9.

Figure 106-8. Provisioned P32E1DS1 TDM2ETH Port

Page 116: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 116/314

3EM23954ABIssue 01, February 2010

Provision Equipment Ports4-64

DLP-106

The Alarms&Settings screen displays.

22 Select Settings tab. See Figure 106-10.

Figure 106-9. Resource List Area: P2E3DS3 Selected

Page 117: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 117/314

Page 118: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 118/314

Page 119: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 119/314

3EM23954ABIssue 01, February 2010

Provision Equipment Ports 4-67

DLP-106

Provision TDM2ETH Service Profile

See Figure 106-13 for the following steps:

31 Select the Payload Size drop-down menu and select payload size in Mb/s.

32 Select the TDM Clock Source drop-down menu and select TDM Clock Source: Adaptive 

or Differential.

33 Enter the unique ECID Tx  value.

34 Enter the unique ECID Rx  value.

Figure 106-12. Provision P2E3DS3 for TDM2ETH Port

Page 120: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 120/314

3EM23954ABIssue 01, February 2010

Provision Equipment Ports4-68

DLP-106

35 Click Apply.

36 STOP. This procedure is complete.

Figure 106-13. Provisioned P2E3DS3 TDM2ETH Port

Page 121: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 121/314

Page 122: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 122/314

3EM23954ABIssue 01, February 2010

Deprovision Equipment Ports4-70

DLP-107

Deprovision CSM SFP Port#5

4 Select Equipment Type drop-down menu, select type EMPTY. See Figure 107-2.

Figure 107-1. Resource List Area: CSM SFP Slot Selected

Page 123: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 123/314

3EM23954ABIssue 01, February 2010

Deprovision Equipment Ports 4-71

DLP-107

5 Click Apply.

The selected CSM slot SFP port #5 will display empty. See Figure 107-3.

NOTE: CSM Port #5 will not deprovision if the port has any Cross-Connections associated

with the port.

Figure 107-2. Provisioned CSM SFP Port #5

Page 124: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 124/314

3EM23954ABIssue 01, February 2010

Deprovision Equipment Ports4-72

DLP-107

6 Go to step 18.

Deprovision DS1 P32E1DS1 Port

7 Double left click the DS1 (P32E1DS1) card in the Resource List Area. See

Figure 107-4.

Figure 107-3. Deprovisioned CSM SFP Port#5

Page 125: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 125/314

Page 126: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 126/314

3EM23954ABIssue 01, February 2010

Deprovision Equipment Ports4-74

DLP-107

See Figure 107-6 for the following steps:

9 Select DS1 port number to deprovision: 01 to 32 .

10 Select the Signal Mode drop-down menu and select signal mode type: Disabled.

11 Click Apply.

Figure 107-5. Provisioned P32E1DS1

Page 127: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 127/314

3EM23954ABIssue 01, February 2010

Deprovision Equipment Ports 4-75

DLP-107

Deprovisioned port will display Disabled. See Figure 107-7.

NOTE: P32E1DS1 Ports will not deprovision if the port has a Cross-Connection associated

with the port.

Figure 107-6. Deprovision P32E1DS Port

Page 128: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 128/314

Page 129: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 129/314

3EM23954ABIssue 01, February 2010

Deprovision Equipment Ports 4-77

DLP-107

The Alarms&Settings screen displays.

14 Select Settings tab. See Figure 107-9.

Figure 107-8. Resource List Area: P2E3DS3 Selected

Page 130: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 130/314

3EM23954ABIssue 01, February 2010

Deprovision Equipment Ports4-78

DLP-107

See Figure 107-10 for the following steps:

15 Select DS3 port number to deprovision, 01 or 02.

16 Select the Signal Mode drop-down menu and select signal mode type: Disabled.

17 Click Apply.

Figure 107-9. Provisioned P2E3DS3

Page 131: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 131/314

3EM23954ABIssue 01, February 2010

Deprovision Equipment Ports 4-79

DLP-107

Deprovisioned port will display Disabled. See Figure 107-11.

NOTE: P2E3DS3 Ports will not deprovision if the port has a Cross-Connection associated

with the port.

Figure 107-10. Deprovision P2E3DS3 Port

Page 132: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 132/314

3EM23954ABIssue 01, February 2010

Deprovision Equipment Ports4-80

DLP-107

18 STOP. This procedure is complete.

Figure 107-11. Deprovisioned P2E3DS3 Ports

Page 133: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 133/314

3EM23954ABIssue 01, February 2010

Provision Ethernet Ports 4-81

DLP-108

DLP-108

Provision Ethernet Ports

PURPOSE

This procedure is used to provision Ethernet ports.

GENERAL

CSM card provisioning requirements depend on how the Ethernet and NMS ports on the front panel

of the card are being used. If the CSM Ethernet ports are being used to interface external Ethernet

equipment and TMN (SNMP) is not being used to monitor and control the NE, then only the Ethernet

Physical Interface needs to be provisioned. The TMN Interface is disabled. If Ethernet port 4 or the

NMS port on the CSM card is being used to transport TMN data, then both the Ethernet Physical

Interface and TMN Interface need to be provisioned.

The NMS port is normally reserved for Craft Terminal interface with the PC. When enabled, theNMS port can be used to daisy chain TMN data to other equipment at the site. The serial data

interface with the PC for the Craft Terminal on the NMS port is always enabled and requires no

special provisioning.

STEP PROCEDURE

1 Select action.

To Provision CSM 10/100/1000 BaseT Ethernet Interfaces, go to step 2.

To Provision CSM Ethernet SFP Interface, go to step 13.

Provision Physical CSM Ethernet Interfaces

10/100/1000 Base T Ethernet Interfaces

2 Select the MSS/Core-Main slot #n in the Resource Tree area. The selected name will be

highlighted in yellow. This selection should also highlight the MSS/Core card in blue

Resource List Area.

3 Double left click the blue MSS/Core-Main (CSM) Card.

Page 134: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 134/314

3EM23954ABIssue 01, February 2010

Provision Ethernet Ports4-82

DLP-108

Ethernet Physical Interface Settings Tab will display.

4 Select Ethernet Physical Interface tab.

5 Select Ethernet Port number to provision (Ethernet Port #1/#4 ).

6 Selecting Settings tab.

Figure 108-1. 9500 MPR Equipment Tab: CSM Card Selected

Page 135: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 135/314

3EM23954ABIssue 01, February 2010

Provision Ethernet Ports 4-83

DLP-108

7 Enable Port Status, select enabled [checked].

8 Click Port Status Apply button to enable port status.

9 Select auto-negotiation parameters to correspond to capabilities of link partner:

a. Select Advertised Capability: 10 Mb/s - Half Duplex, 10 Mb/s - Full Duplex, 100

Mb/s - Half Duplex, 100 Mb/s - Full Duplex, or 1000 Mb/s - Full Duplex.

b. Select Auto Negotiation Status: disabled (unchecked), or enabled (checked).

c. Select Flow Control: (disabled [unchecked], or enabled [checked]).

10 Click Apply.

Figure 108-2. CSM Ethernet Physical Interface: Settings Tab

Page 136: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 136/314

3EM23954ABIssue 01, February 2010

Provision Ethernet Ports4-84

DLP-108

11 Close window.

12 Go to step 23.

Provision CSM Ethernet SFP Interface

13 Select the MSS/Core-Main slot #1 in the Resource Tree area. The selected name will be

highlighted in yellow. This selection should also highlight the MSS/Core card in blue

Resource List Area.

14 Double left click the blue MSS/Core-Main (CSM) Card and the Settings Tab for the

Ethernet Physical Interface will display.

Ethernet Physical Interface Settings Tab will display.

15 Select Ethernet Physical Interface tab.

16 Select Ethernet Port number #5 .

17 Selecting Settings tab.

Figure 108-3. 9500 MPR Equipment Tab: CSM Card Selected

Page 137: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 137/314

3EM23954ABIssue 01, February 2010

Provision Ethernet Ports 4-85

DLP-108

18 Enable Port Status, select Enabled [checked].

19 Click Port Status Apply.

20 Select auto-negotiation parameters to correspond to capabilities of link partner:

a. Select Auto Negotiation Status: disabled (unchecked), or enabled (checked).

b. Select Flow Control: (disabled [unchecked], or enabled [checked]).

21 Click Apply.

Figure 108-4. CSM Ethernet Physical Interface: SFP Settings Tab

Page 138: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 138/314

Page 139: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 139/314

Page 140: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 140/314

3EM23954ABIssue 01, February 2010

Provision Radio Parameters4-88

DLP-109

3 Configure radio with fixed or adaptive modulation?

If fixed modulation, go to step 4.

If adaptive modulation, go to step 12.

Provision Fixed Modulation

4 From the Mode drop-down menu select Presetting.

5 From the Reference Channel Spacing drop-down menu, select desired channel spacing

(10, 30, 40, or 50 MHz).

6 From the Modulation drop-down menu, select modulation scheme (4, 16, 32, 128, or

256 QAM).

Figure 109-2. Provision Radio Channel Fixed Modulation Parameters

Page 141: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 141/314

3EM23954ABIssue 01, February 2010

Provision Radio Parameters 4-89

DLP-109

7 Select the Channel #1 shifter frequency, from the channel #1 Shifter (MHz) drop-down

menu, choose the TX (Go) and RX (Return) Separation Frequency.

8 When the ODU is connected to the MSS-8 shelf, the Channel #1 TxFreq(KHz) field is

automatically populated. If the ODU is not connected, enter the TX RF Frequency

within the allowed range.

9 The Rx Freq (KHz) displays the Rx RF Frequency.

NOTE: The Channel #1 Rx Freq (KHz) field displays the Rx RF Frequency and is the result of

the following calculation:

RX Frequency = TX Frequency - Shifter Frequency

10 Click Apply.

NOTE: In a Protected MOD300 configuration, the Main and Protect MOD300cards use the same CT screen. The parameters on the Main (Channel #1) part

of the screen is a mirror image of the Protect (Channel #0) part of the screen.

Channel #0 fields will be automatically filled in to match Channel #1.

11 Go to step 19.

Provision Adaptive Modulation

12 From the Mode drop-down menu select Adaptive Modulation.

Page 142: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 142/314

3EM23954ABIssue 01, February 2010

Provision Radio Parameters4-90

DLP-109

13 From the Modulation range drop-down menu, select modulation range.

14 From the Reference Channel Spacing drop-down menu, select desired channel spacing

(10 or 30 MHz).

15 Select the Channel #1 shifter frequency, from the channel #1 Shifter (MHz) drop-down

menu, choose the TX (Go) and RX (Return) Separation Frequency.

16 When the ODU is connected to the MSS-8 shelf, the Channel #1 TxFreq(KHz) field is

automatically populated. If the ODU is not connected, enter the TX RF Frequency

within the allowed range.

Figure 109-3. Provision Radio Channel Adaptive Modulation Parameters

Page 143: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 143/314

3EM23954ABIssue 01, February 2010

Provision Radio Parameters 4-91

DLP-109

17 The Rx Freq (KHz) displays the Rx RF Frequency.

NOTE: The Channel #1 Rx Freq (KHz) field displays the Rx RF Frequency and is the result of

the following calculation:

RX Frequency = TX Frequency - Shifter Frequency

18 Click Apply.

NOTE: In a Protected MOD300 configuration, the Main and Protect MOD300

cards use the same CT screen. The parameters on the Main (Channel #1) part

of the screen is a mirror image of the Protect (Channel #0) part of the screen.

Channel #0 fields will be automatically filled in to match Channel #1.

Provision MOD300 Radio Protection Scheme

19Select the MSS/RADIO Dir#-Ch# in the Resource Tree area. The selected name will be

highlighted in yellow. This selection also highlights the MOD300 Card icon in blue in

the resource List Area.

20 Select Settings tab.

Figure 109-4. MOD300 Radio Settings Tab

Page 144: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 144/314

3EM23954ABIssue 01, February 2010

Provision Radio Parameters4-92

DLP-109

21 Select the Protection Type drop-down menu and select: No Protection, 1+1 HSB, or 1+1

FD protection scheme.

22 Select the Protect port.

23 Click Apply.

24 STOP. This procedure is complete.

Figure 109-5. MOD300 Radio Protection Provisioned

Page 145: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 145/314

3EM23954ABIssue 01, February 2010

Provision Synchronization 4-93

DLP-110

DLP-110

Provision Synchronization

PURPOSE

This procedure is used to provision NE synchronization.

GENERAL

 All 9500 MPR radios in the network must be synchronized to the same clock. One radio in the

network is provisioned Master. All other radios in the network must be provisioned Slave. The slave

radios all sync to the clock provided by the master.

STEP PROCEDURE

1 Select the Synchronization tab.

2 Select Synchronization Source icon in the Resource Tree Area.

3 Click on the Settings Tab in the Resource Detail Area.

Figure 110-1. Synchronization Settings Tab

Page 146: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 146/314

3EM23954ABIssue 01, February 2010

Provision Synchronization4-94

DLP-110

4 Provision which synchronization role?

If master, then go to step 5.

If slave, go to step 19.

Provision Master Synchronization

5 Select Master  radio button in the Role  partition.

6 Select Restoration mode radio button desired: Revertive or Not Revertive.

7 Select Primary Source radio button desired: Free Run Local Oscillator , E1/DS1 Port, or

Sync-In Port.

8 Which primary source was selected?

If Sync-In Port, go to step 9.

If E1/DS1 Port, select the E1/DS1 Port from the drop-down menu. Then

go to step 12.

If Free Run Local Oscillator, go to step 17.

9 In the Sync Ports partition, select the Sync In port frequency from the Sync-In Port

drop-down menu: 2.048 MHz, 5 MHz, or 10 MHz.

10 Select Secondary Source radio button desired: Free Run Local Oscillator , or E1/DS1 Port.

11 Go to step 13.

12 Select Secondary Source radio button desired: Free Run Local Oscillator , E1/DS1 Port, orSync-In Port.

13 Which secondary source was selected?

If Free Run Local Oscillator, go to step 15.

If E1/DS1 Port, select the E1/DS1 Port from the drop-down menu. Then

go to step 15.

If Sync-In Port, go to step 14.

14 In the Sync Ports partition, select the Sync In port frequency from the Sync-In Port

drop-down menu: 2.048 MHz, 5 MHz, or 10 MHz.

15 Provision Sync Out Port?

If yes, go to step 16.

If no, go to step 17.

Page 147: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 147/314

3EM23954ABIssue 01, February 2010

Provision Synchronization 4-95

DLP-110

16 In the Sync Ports partition, select the Sync Out port frequency from the Sync-Out Port

drop-down menu: 2.048 MHz, 5 MHz, or 10 MHz.

17 Click Apply.

18 Go to step 31.

Provision Slave Synchronization

19 Select Slave radio button in the Role  partition.

20 Select Primary Source radio button desired: Sync-In Port, or Radio Port.

21 Which primary source was selected?

If Sync-In Port, go to step 22.

If Radio Port, select the Radio Port from the drop-down menu. Then go

to step 25.

22 In the Sync Ports partition, select the Sync In port frequency from the Sync-In Port

drop-down menu: 2.048 MHz, 5 MHz, or 10 MHz.

Figure 110-2. Synchronization - Master / Revertive

Page 148: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 148/314

3EM23954ABIssue 01, February 2010

Provision Synchronization4-96

DLP-110

23 Select Secondary Source radio button desired: Free Run Local Oscillator  or E1/DS1 Port.

24 Go to step 28.

25 Select Secondary Source radio button desired: Free Run Local Oscillator , E1/DS1 Port, orSync-In Port.

26 Which secondary source was selected?

If Free Run Local Oscillator, go to step 28.

If E1/DS1 Port, select the E1/DS1 Port from the drop-down menu. Then

go to step 28.

If Sync-In Port, go to step 27.

27 In the Sync Ports partition, select the Sync In port frequency from the Sync-In Port

drop-down menu: 2.048 MHz, 5 MHz, or 10 MHz.

28 Provision Sync Out Port?

If yes, go to step 29.

If no, go to step 30.

29 In the Sync Ports partition, select the Sync Out port frequency from the Sync-Out Port

drop-down menu: NOT USED, 2.048 MHz, 5 MHz, or 10 MHz.

Page 149: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 149/314

3EM23954ABIssue 01, February 2010

Provision Synchronization 4-97

DLP-110

30 Click Apply.

31 STOP. This procedure is complete.

Figure 110-3. Synchronization - Slave / Revertive

Page 150: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 150/314

3EM23954ABIssue 01, February 2010

Provision Synchronization4-98

DLP-110

Page 151: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 151/314

3EM23954ABIssue 01, February 2010

Provision Cross Connections 4-99

DLP-112

DLP-112

Provision Cross Connections

PURPOSE

This procedure is used to provision cross connections.

GENERAL

Cross connection is only required for TDM traffic. Generic Ethernet traffic is handled automatically

via MAC Address learning in the Ethernet switch. Cross connections can also be used with point-to-

point VLAN Ethernet traffic to direct traffic based on a VLAN tag rather than MAC address.

The cross connections screen is used to configure switching of packetized data through the CSM

(Control and Switching Module - Core) card. Using this screen, the operator can switch:

•   DS1/DS3 (ports) lines from/to a P32E1DS1/P2E3DS3 (PDH DS1/DS3 icons) cardto/from a MOD300 (RADIO icons) card and/or any of four Ethernet (ETH icons)

ports on the CSM card.

•   Ethernet (ETH icons) data from/to an external source to/from a MOD300 (RADIO

icons) card and/or to/from an P32E1DS1/P2E3DS3 (PDH DS1/DS3 icons) card.

The screen allows the operator to select DS1/DS3 (PDH icons), Ethernet (ETH icons), and/or

MOD300 (RADIO icons) ports as source and destination ports and provides a graphical presentation

of the switch functions.

The license key installed on the CSM determines the Ethernet data capacity that can be crossconnected.

Valid Cross Connections:

•   PDH to Radio: 

 – PDH (P32E1DS1 card) to RADIO (MOD300 card)

 – PDH (P2E3DS3 card) to RADIO (MOD300 card)

•   PDH to Ethernet: 

 – PDH (P32E1DS1 card) to ETH (Ethernet)

 – PDH (P2E3DS3 card) to ETH (Ethernet)

•   Ethernet to Radio: 

•   Radio to Radio: 

Page 152: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 152/314

3EM23954ABIssue 01, February 2010

Provision Cross Connections4-100

DLP-112

 After a cross connection has been created, two cross connected slots are visually linked by a line: a

line in the context of this application represents a bundle of flows, which share same source and

destination entity. In addition, all 802.1Q tagged Ethernet traffic having the same VLAN ID as cross

connection Flow ID number will only be forwarded between these cross connected slots.

Point to Point VLAN

The Point to Point (P2P) VLAN cross connect feature allows the user to direct VLAN-tagged traffic

between specified Ethernet and/or radio ports. Rather than directing all traffic to and from the cross

connected ports, the feature directs Ethernet traffic where the VLAN tag matches the cross connect

Flow ID.

•   When making the connection for a P2P VLAN flow (Ethernet port to radio), the

user should enter a MAC address of all 0's (000000000000). P2P VLAN cross

connects will direct matching VLAN-tagged Ethernet traffic to the cross

connected ports regardless of the destination MAC address in the Ethernet

frames.

•   Ethernet traffic entering the cross connected port with a VLAN tag matching the

flow id will be directed only to the port on the other end of the cross connect.

Traffic will not be flooded. This will also take precedence over any MAC address

learning for VLAN-tagged traffic that matches the flow id in the cross connect.

•   Ethernet traffic entering the cross connected port with no VLAN tag or VLAN tags

that do not match the flow id specified in the cross connect will flood to all ports

until MAC address learning takes place. The P2P VLAN cross connect will have

no effect on this traffic.

•  VLAN tagged Ethernet traffic that enters a port will be dropped if the VLAN tag matches the

flow id of a cross connect that is on a different port.

The user must know the Ethernet VLAN ID, provisioned by the customer, before provisioning/cross

connecting DS1/DS3 data lines.

Each radio link can handle a maximum of 256 VLAN IDs.

When configuring MPLS T1's via ethernet through a multi-path 9500 MPR network (Nx1+0/1),

Point-to-Point VLAN (P2P VLAN) cross-connects will be required to restrict the traffic to one

radio/Ethernet port combination. This is because the multiple path connections will deliver several

copies of the LDP messages between the MPLS T1's NE's causing regular traffic interruptions. When

there are 3 radio links between the same two shelves, 3 copies of each LDP message are delivered to

the MPLS T1's. Creating the P2P VLAN Cross-Connect between the ethernet port and radio (wherethe MPLS T1's connects) allows only one copy of the message to reach the MPLS T1's and corrects

the problem.

Page 153: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 153/314

3EM23954ABIssue 01, February 2010

Provision Cross Connections 4-101

DLP-112

Flow ID number Rules

The Flow ID number entered by the operator on the MSS/DS1 or MSS/DS3 provisioning screen is

one of the parameters the software management uses to determine source, destination, and direction

of the DS1/DS3 port when the data is switched in the Core (CSM) card. The following rules apply to

the Flow ID:

1. Number is unique to the entire network. It cannot be used in any other radio or

hop in the network.

2. Range of Flow ID numbers to choose from is determined by total number of Flow

ID's in the network. Refer to Table 112-A  for Range of Flow ID's. If there are fewer

than 256 cross connects in the network, select Flow ID from the Less Than or Equal

to 256 Range. If there are more than 256 but less than 512 cross connects, select

Flow ID from the More Than 256, Less Than 512 Range.

Ranging

Ranging allows the operator to enter multiple cross-connects simultaneously. When multiple

cross-connections are required between the same two ports, the MAC Address is the same, andmultiple Flow IDs are to be cross-connected, ranging can be used to enter the cross-connections at

the same time.

When multiple cross-connections are required between the same two ports, the MAC Address is the

same, and the Flow IDs are sequential, ranging can be used to enter the cross-connections at the

same time. In the Flow ID field, enter the end points of the sequence using the notation [n-m]; where

‘n’ equals the start value of the sequence and ‘m’ equals the stop value of the sequence. Example: to

enter cross-connections for Flow IDs 147 through 156, in the Flow ID field enter “147-156 ”. See

Figure 112-1.

When multiple cross-connections are required between the same two ports, the MAC Address is the

same, and the Flow IDs are not sequential, ranging can be used to enter the cross-connections at thesame time. In the Flow ID field, enter the multiple Flow IDs separated by commas. Example: to enter

cross-connections for Flow IDs 47, 62, 135, and 201, in the Flow ID field enter “47,62,135,201”. See

Figure 112-2.

To ensure successful completion of the cross-connection requests, the user should limit the number

of cross-connections created using a single ranging operation to ten.

Ranging is supported for Radio to Radio and Ethernet to Radio Cross-Connection entry.

Table 112-A. Range of Flow ID’s

Flow ID Range

Less Than or 

Equal to 256

2-255, 256-511, 512-767, 768-1023, 1024-1279, 1280-1535, 1536-1791, 1792-

2047, 2048-2303, 2304-2559, 2560-2815, 2816-3071, 3072-3327, 3328-3583,

3584-3839, 3840-4080

More Than 256,

Less Than 512

2-511, 512-1023, 1024-1535, 1536-2047, 2048-2559, 2560-3071, 3072-3583,

3584-4080

Page 154: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 154/314

3EM23954ABIssue 01, February 2010

Provision Cross Connections4-102

DLP-112

Ranging is supported for PtP VLAN Cross-Connection entry.

Destination MAC Address

The destination MAC address is dependent upon the protection scheme of the destination port. For

destination ports which are configured unprotected, the first two digits of the destination MAC

 Address must be set to ‘unicast’ or ‘00’. For destination ports which are configured 1+1 protection,

the first two digits of the destination MAC Address must be set to ‘multicast’ or ‘01’.

The destination MAC address for P2P VLAN cross-connects must be set to ‘00:00:00:00:00:00’.

Example #1: The destination port is unprotected and the NE MAC Address is “00:43:23:19:87:92”. In

the Cross Connection MAC Address field, enter: “00 :43:23:19:87:92”.

Example #2: The designating port is 1+1 protected and the NE MAC Address is “00:43:23:19:87:92”.

In the Cross Connection MAC Address field, enter: “01:43:23:19:87:92”.

Example #3: The cross-connect is a P2P VLAN, the destination port is set to “00:00:00:00:00:00”. In

the Cross Connection MAC Address field, enter: “00:00:00:00:00:00”.

Figure 112-1. Ranging Sequential Flow IDs

Figure 112-2. Ranging Non-Sequential Flow IDs

Page 155: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 155/314

3EM23954ABIssue 01, February 2010

Provision Cross Connections 4-103

DLP-112

PDH to Radio:

CAUTION: Possibility of service interruption. In the protected CSM configuration,

entering DS1 cross-connections while the spare CSM is Active may affect existing DS1

cross-connections. To prevent this from occurring, ONLY provision DS1

cross-connections while the main CSM card is Active.

PREREQUISITES

Each DS1/DS3 card and MOD300 card must be enabled on the respective DS1/DS3 and MOD300

card provisioning screens.

The Service Profile on the each DS1/DS3 card Settings screen must be set to TDM2TDM for each

DS1/DS3 cross connect when both termination points of the DS1/DS3 circuit are terminated on

9500 MPR equipment.

The Service Profile on the each DS1/DS3 card Settings screen must be set to TDM2ETH for each

DS1/DS3 cross connect when one of the termination points of the DS1/DS3 circuit are terminated onnon-9500 MPR equipment, and the other equipment is MEF-8 compliant.

Each DS1/DS3 line to be cross connected must have a unique Flow ID number assigned to it on the

respective DS1/DS3 card Settings screen.

PDH to Ethernet:

CAUTION: Possibility of service interruption. In the protected CSM configuration,

entering DS1 cross-connections while the spare CSM is Active may affect existing DS1

cross-connections. To prevent this from occurring, ONLY provision DS1

cross-connections while the main CSM card is Active.

PREREQUISITES

The DS1/DS3 card (source) and CSM card (destination) must be enabled on the respective DS1/DS3

card and CSM card provisioning screens.

The Service Profile on the DS1/DS3 card Settings screen must be set to TDM2ETH for each DS1/DS3

cross connected.

Ethernet to Radio:

PREREQUISITES

The Ethernet port (source) and MOD300 card (destination) must be enabled on the respective CSMand MOD300 card provisioning screens.

Ranging Flow ID entry is supported.

The Service Profile on theDS1/DS3 card Settings screen must be set to TDM2ETH for each DS1/DS3

cross connected.

Page 156: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 156/314

3EM23954ABIssue 01, February 2010

Provision Cross Connections4-104

DLP-112

Radio to Radio:

PREREQUISITES

Both MOD300 cards must be enabled on the respective MOD300 card provisioning screens.

•   When making a cross connection between two radio cards, use the TDM2TDM

service profile if the termination points of the circuit are configured TDM2TDM.

•   Use the TDM2ETH service profile if the termination points of the circuit are

configured TDM2ETH.

•   Use the TDM2ETH service profile when making the point-to-point VLAN

connection.

Ranging Flow ID entry is supported.

The Service Profile on the DS1/DS3 card Settings screen must be set for each DS1/DS3 cross connected.

Icon Shapes

The shape of the icon identifies the module in the slot as RADIO (MD300 module) or PDH

(P32E1DS1/P2E3DS3 modules) or one of four ETH (Ethernet) connectors on the CSM module.

Icon Colors

The colors of the icons on the cross connections screen can be used to quickly determine the current

state of the source and destination.

The icon colors are defined as follows:

•   White icon indicates the ports are enabled but are not currently cross connected.

•   Blue icon on RADIO and PDH (P32E1DS1/P2E3DS3) ports indicates the ports are

disabled or fully cross connected.

•   Blue icon on ETH (Ethernet) ports indicates the ports are disabled.

•   Green icon indicates that the ports are cross connected.

RADIO PORTS

MOD300

CARD(S)

PDH PORTS

P32E1DS1 /

P2E3DS3

CARDS

ETH PORTS

Ethernet

Connectors on

CSM CARDS

Page 157: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 157/314

3EM23954ABIssue 01, February 2010

Provision Cross Connections 4-105

DLP-112

Line Colors

The drag and drop line, the operator inserts, between icons indicates an electrical connection. The

color of the line indicates type of data and direction.

The icon colors are defined as follows:

•   Black Line - PDH (P32E1DS1/P2E3DS3) to RADIO (MD300)

•   Blue Line - PDH (P32E1DS1/P2E3DS3) to ETH (Ethernet)

•   Red Line - RADIO (MD300) to RADIO (MD300)

•   Green Line - RADIO (MD300) to ETH (Ethernet)

Figure 112-3. Cross Connection: Line Color Detail

Page 158: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 158/314

3EM23954ABIssue 01, February 2010

Provision Cross Connections4-106

DLP-112

STEP PROCEDURE

1 CAUTION: Possibility of service interruption. Entering DS1 cross-connections while

the spare CSM card is Active may affect existing DS1 cross-connections. To preventthis from occurring, ONLY provision DS1 cross-connections while the main CSM is

Active.

2 Select Configuration/Cross Connections.

The Cross Connections window opens. See Figure 112-4.

3 Select Action?

If PDH to Radio (TDM2ETH), then go to step 4.

If PDH to Ethernet (TDM2ETH), then go to step 16.

Figure 112-4. Configuration Cross Connection Window

Page 159: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 159/314

3EM23954ABIssue 01, February 2010

Provision Cross Connections 4-107

DLP-112

If Ethernet to Radio (TDM2ETH), then go to step 27.

If Radio to Radio, then go to step 36.

Provision PDH to Radio Cross Connection

4 Is the system configured with protected CSM cards?

If yes, go to step 5.

If no, go to step 9.

5 CAUTION: Possibility of service interruption. In the protected CSM configuration,

entering DS1 cross-connections while the spare CSM is Active may affect existing

DS1 cross-connections. To prevent this from occurring, ONLY provision DS1

cross-connections while the main CSM is Active.

6 Select Protection Schemes tab.

7  Verify the main CSM card is in the Active state.

8 Is the main CSM card in the Active state?

If yes, go to step 9.

If no, determine the reason the main CSM card is in the Standby state

and correct the condition prior to continuing with this procedure.

9 On the Cross Connection window, select PDH port and drag and draw line to RADIO.

PDH-RADIO pop-up displays. See Figure 112-5.

Page 160: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 160/314

3EM23954ABIssue 01, February 2010

Provision Cross Connections4-108

DLP-112

10 On the PDH_RADIO pop-up, select check box for all Flow ID numbers to be cross

connected.

11 On the PDH_RADIO pop-up, click OK.

12 On the Cross Connection screen, click Apply.

13 From the Connections tab, verify the PDH_RADIO cross-connection was entered

correctly.

14 Go to step 42.

Figure 112-5. PDH-RADIO Cross Connection

Page 161: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 161/314

3EM23954ABIssue 01, February 2010

Provision Cross Connections 4-109

DLP-112

Provision PDH to Ethernet Cross Connection

15 Is the system configured with protected CSM cards?

If yes, go to step 16.

If no, go to step 20.

16 CAUTION: Possibility of service interruption. In the protected CSM configuration,

entering DS1 cross-connections while the spare CSM is Active may affect existing

DS1 cross-connections. To prevent this from occurring, ONLY provision DS1

cross-connections while the main CSM is Active.

17 Select Protection Schemes tab.

18  Verify the main CSM card is in the Active state.

19 Is the main CSM card in the Active state?

If yes, go to step 20.

If no, determine the reason the main CSM card is in the Standby state

and correct the condition prior to continuing with this procedure.

20 On the Cross Connection window, select PDH port and drag and draw line to ETH

port.

PDH-ETH pop-up displays. See Figure 112-6.

Page 162: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 162/314

3EM23954ABIssue 01, February 2010

Provision Cross Connections4-110

DLP-112

21 On the PDH-Eth pop-up, select Flow ID number from Flow ID drop-down list.

22 Enter the destination MAC address where the PDH will be terminated in the MAC

 Address field.

NOTE: The first two digits of the destination MAC address for unprotected

 ports must be set to ‘unicast’ or ‘00’. The first two digits of the destination MAC

address for 1+1 protected ports must be set to ‘multicast’ or ‘01’.

23 On the PDH-ETH pop-up, click OK.

24 On the Cross Connection screen, click Apply.

25 From the Connections tab, verify the PDH-ETH cross-connection was entered

correctly.

Figure 112-6. PDH to Ethernet Cross Connection

Page 163: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 163/314

3EM23954ABIssue 01, February 2010

Provision Cross Connections 4-111

DLP-112

26 Go to step 42.

Provision Ethernet to Radio Cross Connection

27 Select ETH port and drag and draw line to Radio port.

RADIO-ETH pop-up displays. See Figure 112-7.

28 On the RADIO-ETH pop-up, enter Flow ID number in the Flow ID field.

NOTE: Ranging is supported for RADIO-ETH Cross-Connection entry.

29 Select TDM2TDM or TDM2ETH in the Profile drop-down menu.

30 Select ADAPTIVE or DIFFERENTIAL in the TDM Clock Source drop-down menu.

Figure 112-7. Ethernet to Radio Cross Connection

Page 164: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 164/314

3EM23954ABIssue 01, February 2010

Provision Cross Connections4-112

DLP-112

31 Enter the destination MAC address where the RADIO will be terminated in the MAC

 Address field.

NOTE: The first two digits of the destination MAC address for unprotected

 ports must be set to ‘unicast’ or ‘00’. The first two digits of the destination MAC

address for 1+1 protected ports must be set to ‘multicast’ or ‘01’.

32 On the RADIO-ETH pop-up, click OK.

33 On the Cross Connection screen, click Apply.

34 From the Connections tab, verify the RADIO-ETH cross-connection(s) were entered

correctly.

35 Go to step 42.

Provision Radio to Radio Cross Connection

36 Select Radio port and drag and draw line to Radio port.

RADIO-RADIO pop-up displays. See Figure 112-8.

Page 165: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 165/314

3EM23954ABIssue 01, February 2010

Provision Cross Connections 4-113

DLP-112

37 On the RADIO-RADIO pop-up, enter Flow ID number for the far-end in the Flow ID

field.

NOTE: Ranging is supported for RADIO-RADIO Cross-Connection entry.

38 Select TDM2TDM or TDM2ETH in the Profile drop-down menu.

39 On the RADIO-RADIO pop-up, click OK.

40 On the Cross Connection screen, click Apply.

41 From the Connections tab, verify the RADIO-RADIO cross-connection(s) were entered

correctly.

42 STOP. This procedure is complete.

Figure 112-8. Radio to Radio Cross Connection

Page 166: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 166/314

3EM23954ABIssue 01, February 2010

Provision Cross Connections4-114

DLP-112

Page 167: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 167/314

3EM23954ABIssue 01, February 2010

View Alarms 4-115

DLP-113

DLP-113

View Alarms

PURPOSE

This procedure provides instructions to view alarms for the 9500 MPR.

GENERAL

The 9500 MPR Alarm Monitor allows the user to view current alarms and a log of alarm activity.

Both the current alarms and the alarm logs may be sorted by alarm severity. The following is a list

of alarm filtering available:

•   CURRENT ALARMS:

 – Global

 – Critical (CRI)

 – Major (MAJ)

 – Minor (MIN)

 – Warning (WRG)

 – Indicator (IND)

•   ALARM LOG: Global

 – Global

 – Critical (CRI)

 – Major (MAJ)

 – Minor (MIN)

 – Warning (WRG)

 – Indicator (IND)

 – Cleared (CLR)

STEP PROCEDURE

View NE Alarms

1 Select Diagnosis/Alarms/NE Alarms. See Figure 113-1.

Page 168: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 168/314

3EM23954ABIssue 01, February 2010

View Alarms4-116

DLP-113

The Alarm Monitor window opens. See Figure 113-2.

The Alarm Monitor allows the user to view alarms by severity.

Figure 113-1. View NE Alarms Path

Figure 113-2. Alarm Monitor Window

Page 169: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 169/314

3EM23954ABIssue 01, February 2010

View Alarms 4-117

DLP-113

2 Select CURRENT_ALARMS: MAJ from the Alarm Manager resource tree area.

The Synthesis pane displays the CURRENT_ALARMS: MAJ tab. See Figure 113-3.

3 STOP. This procedure is complete.

Figure 113-3. Alarm Manager: Current Alarms Major Tab

Page 170: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 170/314

3EM23954ABIssue 01, February 2010

View Alarms4-118

DLP-113

Page 171: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 171/314

3EM23954ABIssue 01, February 2010

View Abnormal Condition List 4-119

DLP-114

DLP-114

View Abnormal Condition List

PURPOSE

This procedure provides instructions to view abnormal condition list for the 9500 MPR.

GENERAL

This abnormal condition list is a read-only screen that lists non-usual conditions present in the NE. Eventsthat cause an abnormal condition:

•   Forced switch (EPS, RPS, TPS)

•   Lockout (EPS, RPS, TPS)

  Loopback activation

•   Local radio Tx mute (manual)

•   Local radio Tx mute (automatic)

•   Remote radio Tx mute (manual)

STEP PROCEDURE

1 Select Diagnosis/Abnormal Condition List.

The Abnormal Condition List window opens.

Figure 114-1. Abnormal Condition List Path

Page 172: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 172/314

3EM23954ABIssue 01, February 2010

View Abnormal Condition List4-120

DLP-114

2 Click Close.

3 STOP. This procedure is complete.

Figure 114-2. Abnormal Condition List Window

Page 173: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 173/314

3EM23954ABIssue 01, February 2010

View Protection Schemes 4-121

DLP-115

DLP-115

View Protection Schemes

PURPOSE

This procedure provides instructions to view Protection Schemes for the 9500 MPR.

STEP PROCEDURE

1 Select Protection Schemes Tab.

The Protection Schemes tab opens. See Figure 115-1.

 All the protection schemes provisioned for the 9500 MPR radio are displayed in the

main window pane.

2 Expand Protection Schemes in the Resource Tree area. See Figure 115-2.

Figure 115-1. Protection Schemes Tab

Page 174: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 174/314

3EM23954ABIssue 01, February 2010

View Protection Schemes4-122

DLP-115

3 Select action?

To view CSM protection scheme parameters, go to step 4.To view Synchronization protection schemes, go to step 6.

To view Equipment protection schemes, go to step 8

To view Equipment protection schemes, go to step 10

To view HSB protection schemes, go to step 12.

To view Rx Radio protection schemes, go to step 14

View CSM Protection Scheme Parameters

4 Select Protection Schemes/Slot#1-2/Equipment Protection in the Resource Tree area.

The Protection Schemes Parameter tab displays CSM protection scheme parameters

in the main window. See Figure 115-3.

Figure 115-2. Protection Schemes Resource Tree Expanded

Page 175: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 175/314

3EM23954ABIssue 01, February 2010

View Protection Schemes 4-123

DLP-115

5 Go to step 15.

View Synchronization Protection Scheme Parameters

6 Select Protection Schemes/Synchronization Protection in the Resource Tree area.

The synchronization Protection Schemes Parameter tab displays in the main window.

See Figure 115-4.

Figure 115-3. CSM Protection Scheme Parameter Tab

Page 176: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 176/314

3EM23954ABIssue 01, February 2010

View Protection Schemes4-124

DLP-115

7 Go to step 15.

View Radio Channel Protection Schemes Parameters

8 Select Protection Schemes/Radio channel (Dir#x.y) in the Resource Tree area.

The Protection Scheme Parameters tab displays in the main window. See

Figure 115-5.

Figure 115-4. Synchronization Protection Scheme Parameter Tab

Page 177: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 177/314

3EM23954ABIssue 01, February 2010

View Protection Schemes 4-125

DLP-115

9 Go to step 15.

View Equipment Protection Schemes Parameters

10 Select Protection Schemes/Equipment Protection in the Resource Tree area.

The Protection Scheme Parameters tab displays in the main window. See

Figure 115-6.

Figure 115-5. Radio Channel Protection Scheme Parameter Tab

Page 178: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 178/314

3EM23954ABIssue 01, February 2010

View Protection Schemes4-126

DLP-115

11 Go to step 15.

View Hot StandBy Protection Schemes Parameters

12 Select Protection Schemes/HSB Protection in the Resource Tree area.

The HSB Protection Scheme Parameters tab displays in the main window. See

Figure 115-7.

Figure 115-6. Equipment Protection Scheme Parameter Tab

Page 179: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 179/314

3EM23954ABIssue 01, February 2010

View Protection Schemes 4-127

DLP-115

13 Go to step 15.

View Rx Radio Protection Schemes Parameters

14 Select Protection Schemes/Rx Radio Protection in the Resource Tree area.

The Rx Radio Protection Scheme Parameters tab displays in the main window. See

Figure 115-8.

Figure 115-7. HSB Protection Scheme Parameter Tab

Page 180: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 180/314

3EM23954ABIssue 01, February 2010

View Protection Schemes4-128

DLP-115

15 STOP. This procedure is complete.

Figure 115-8. Rx Radio Protection Scheme Parameter Tab

Page 181: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 181/314

3EM23954ABIssue 01, February 2010

Download Provisioning Data 4-129

DLP-116

DLP-116

Download Provisioning Data

PURPOSE

This procedure is used to download provisioning data for the radio.

GENERAL

Report file NEReport.txt is created automatically by radio software and available on the web for

downloading. The report can be opened using the standard web browser and entering into the field

the Radio IP Address or the rack name. The report is password protected.

STEP PROCEDURE

1 Select action?

If download provisioning data using JUSM/CT 9500MPR-A, go to

step 2.

If download provisioning data using web browser, go to step 14.

Download Provisioning Data Using JUSM/CT 9500MPR-A

2 Select Diagnosis/Current Configuration View. See Figure 116-1.

The Current Configuration View window opens. See Figure 116-2.

Figure 116-1. Diagnosis / Current Configuration View Path

Page 182: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 182/314

3EM23954ABIssue 01, February 2010

Download Provisioning Data4-130

DLP-116

3 Select action?

If save Current Configuration data, go to step 4.

If print Current Configuration data, go to step 9.

Save Current Configuration Data

4 Select File/Save As.

5 Navigate to the directory to save 9500MPR Current Configuration View file.

6 Click Save.

7 Select File/Exit.

8 Go to step 20.

Print Current Configuration Data

9 Select File/Print.

Figure 116-2. Diagnosis / Current Configuration View Window

Page 183: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 183/314

3EM23954ABIssue 01, February 2010

Download Provisioning Data 4-131

DLP-116

10 Select Printer to print 9500MPR provisioning verification file.

11 Click OK.

12 Select File/Exit.

13 Go to step 20.

Download Provisioning Data Using Web Browser 

14 In a web browser, type in the radio IP address or the URL (shown below):

http://radio IP Address

9500MPR Web Server login screen displays.

15 Enter NE User ID and Password (same as user ID and password entered on CT).

The 9500MPR Web Server displays.

Figure 116-3. Provision Verification: Web Browser 

Figure 116-4. Provision Verification: Login Window

Page 184: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 184/314

3EM23954ABIssue 01, February 2010

Download Provisioning Data4-132

DLP-116

16 On Main menu, select Configuration Info.

The File Download screen displays.

Figure 116-5. 9500MPR Web Server Main Page

Page 185: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 185/314

3EM23954ABIssue 01, February 2010

Download Provisioning Data 4-133

DLP-116

The File Download screen displays.

17 Click Save.

18 Navigate to the directory to save 9500MPR Current Configuration data.

19 Click Save.

Configuration file output, example of the start of the file:

**********************

* CONFIGURATION INFO *

**********************

Site Name: PLM 9500-165

Site Location: SVT Lab

QoS: Diff Serv

Bridge Address: 0:0:0:0:1:65

Fans: equipped

CORE CONFIGURATION

==================

Type: MSS-8, Enhanced, Protected

ETHERNET PORT

-------------

** Ep 1 **

Disabled

Figure 116-6. Configuration Info File Download Window

Page 186: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 186/314

3EM23954ABIssue 01, February 2010

Download Provisioning Data4-134

DLP-116

Click

** Ep 2 **

Disabled

** Ep 3 **

Disabled

** Ep 4 **

Transport mode

Disabled

** Ep 5 **

 Auto Negotiation: Enabled

BitRate: 1000 Mbit/s

Capability: Full Duplex

Flow Control: Disable

SLOTS CONFIGURATION

===================

** Slot 3 EAS **

ETHERNET PORT

-------------

** Ep 1 **

 Auto Negotiation: Disabled

BitRate: 100 Mbit/s

Capability: Full Duplex

Flow Control: Disable

** Ep 2 **

 Auto Negotiation: Enabled

BitRate:

10 Full Duplex

100 Full Duplex

1000 Full Duplex

Flow Control: Enable

*****************************

* END OF CONFIGURATION INFO *

*****************************

20 STOP. This procedure is complete.

Page 187: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 187/314

3EM23954ABIssue 01, February 2010

 Administer System Settings 4-135

DLP-117

DLP-117

Administer System Settings

PURPOSE

This procedure is used to administer system settings.

GENERAL

The Systems Settings/NE Configuration screen is used to configure the Quality of Service (QoS) type,

enable DHCP Server support, enable event and alarm logging, and retrieve NE MAC Address/Bridge

 Address.

The QoS Classification determines the Ethernet flow that will be transmitted from the CSM (Control

and Switching Module) to the MOD300 in the event of a fade. Typically the high priority traffic

experiences less delay in the CSM switch than the lower priority traffic.

Three QoS settings are available as follows:

•   Disabled

•   802.1

•   DiffServ

802.1p

When 802.1p is selected, the packet is examined for the presence of a valid 802.1p user-priority tag.

If the tag is present, priorities are set based on IEEE 802.1D-2004 Annex G User Priorities and

Traffic Classes that defines seven traffic types and corresponding user priority values.

DiffServ

When DiffServ is selected, the DSCP field of the packet is examined for the presence of one of eight

tags, each identifying one of eight traffic types and corresponding user values

The eight traffic types and corresponding priorities 1- 8 (8 being the highest priority) follow:

Page 188: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 188/314

3EM23954ABIssue 01, February 2010

 Administer System Settings4-136

DLP-117

DHCP Server Support

The default setting for DHCP server support is enabled. In most configurations this is the

recommended provisioning value.

When Port#4 TMN Ethernet Interface is connected to a larger TMN network, it is recommended to

disable DHCP server support to prevent duplicate IP address issues.

Event and Alarm log

To provision Event and alarm logging, select enabled in the Event and Alarm Log Logging field.

To record the NE MAC Address/Bridge Address, retrieve the value from the NE MAC

 Address/Bridge Address field.

STEP PROCEDURE

1 Select Configuration/System Settings tab.

The System Settings tab opens. See Figure 117-1.

Table 117-A. DSCP Traffic Types

PRIORITY TRAFFIC TYPE DESCRIPTION

8 (Highest Priority) TDM2TDM (Always Highest

Priority)

7 TDM2ETH and TMN

6 ETH2ETH

5 Network Control and Voice VoIP, Video conferencing,

 Audio conferencing

4 Video

3 Controlled Load Broadcast (Audio/Video)

2 Best Effort Web Browsing, Chat, Games

1 (Lowest Priority) Background E-mail, database download

Page 189: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 189/314

3EM23954ABIssue 01, February 2010

 Administer System Settings 4-137

DLP-117

2 Select action.

To set QoS Classification, go to step 3.

To set DHCP Server, go to step 7.

To set Event and Alarm Logging, go to step 11.To retrieve NE MAC Bridge Address, go to step 15.

Provision QoS Classification

3 From the QoS Classification drop-down menu, select the desired QoS Classification:

 – Disabled

 – 802.1

 – DiffServ

4 Click Apply.

5 Click Close.

Figure 117-1. System Settings Tab

Page 190: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 190/314

3EM23954ABIssue 01, February 2010

 Administer System Settings4-138

DLP-117

6 Go to step 17.

Provision DHCP Server 

7 From the DHCP Server drop-down menu, select the desired DHCP Server

provisioning:

 – Disabled

 – Enabled

8 Click Apply.

9 Click Close.

Figure 117-2. QoS Classification Drop-Down Menu

Page 191: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 191/314

3EM23954ABIssue 01, February 2010

 Administer System Settings 4-139

DLP-117

10 Go to step 17.

Provision Event and Alarm Log

11 From the Logging drop-down menu, select the Event and Alarm Log provisioning:

 – Disabled

 – Enabled

12 Click Apply.

13 Click Close.

Figure 117-3. DHCP Server Drop-Down Menu

Page 192: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 192/314

3EM23954ABIssue 01, February 2010

 Administer System Settings4-140

DLP-117

14 Go to step 17.

Retrieve NE MAC Address/Bridge Address

15 From the NE MAC Address/Bridge Address field, record the Bridge Address:

16 Click Close.

Figure 117-4. Event and Alarm Log Drop-Down Menu

Page 193: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 193/314

3EM23954ABIssue 01, February 2010

 Administer System Settings 4-141

DLP-117

17 STOP. This procedure is complete.

Figure 117-5. NE MAC Address / Bridge Address

Page 194: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 194/314

3EM23954ABIssue 01, February 2010

 Administer System Settings4-142

DLP-117

Page 195: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 195/314

3EM23954ABIssue 01, February 2010

 Administer Network Configuration 4-143

DLP-118

DLP-118

Administer Network Configuration

PURPOSE

This procedure is used to administer network configuration.

GENERAL

TMN Ethernet port provisioning requirements depend on how the CSM Ethernet port 4 and NMS

port on the CSM card are to be used.

The NMS port is normally reserved for Craft Terminal interface with the PC. The serial data

interface with the PC for the Craft Terminal on the NMS port is default enabled with IP address

10.0.1.2 and requires no special provisioning. For NMS port provisioning other than the default

values, provision TMN Ethernet Interface.

If CSM Ethernet Port#4 is being used to interface external Ethernet equipment, then the Ethernet

Physical Interface Port#4 must be enabled and provisioned and Port#4 TMN Ethernet Interface

must be disabled.

If Port#4 TMN Ethernet interface is used to connect to a larger TMN network and communicate with

other equipment at the site. The Ethernet Physical Interface Port#4 must be disabled, Port#4 TMN

Ethernet Interface must be provisioned and TMN Ethernet Interface must be provisioned.

IP Provisioning is normally performed by the Internet Protocol (IP group). Before starting IP

provisioning, the user must know IP routing and have the following information available:

•   IP Address

•   IP Mask

•   Method of IP routing to be used in network

•   If OSPF (Open Shortest Path First protocol) is the required routing method, the

user must know the number of the OSPF Area the radio is in.

•   TMN Ethernet Interface

STEP PROCEDURE

1 Select action.

To provision NE IP Address, go to step 2.

To administer TMN Ethernet Interface, go to step 7.

To administer TMN Port#4 Ethernet Interface, go to step 26.

To provision IP Static Routing, go to step 47.

To provision Provision OSPF Area, go to step 60.

Page 196: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 196/314

3EM23954ABIssue 01, February 2010

 Administer Network Configuration4-144

DLP-118

Provision IP Address of NE

2 Select Configuration/Network Configuration/Local Configuration.

The Local Configuration window opens.

3 Enter the <IP address> of the NE in the IP Address field.

4 Click Apply.

5 Click Close.

6 Go to step 67.

Administer TMN Ethernet Interface

7 Select the MSS/Core-Main slot #1 in the Resource Tree area. The selected name will be

highlighted in yellow. This selection should also highlight the MSS/Core card in blue

Resource List Area.

8 Double left click the blue MSS/Core-Main (CSM) Card.

Figure 118-1. 9500 MPR NE IP Address Path

Figure 118-2. 9500 MPR NE IP Address

Page 197: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 197/314

3EM23954ABIssue 01, February 2010

 Administer Network Configuration 4-145

DLP-118

Ethernet Physical Interface Settings Tab displays.

9 Select TMN Interface tab.

10 Select TMN Port in left frame.

11 Selecting Settings tab.

Figure 118-3. 9500 MPR Equipment Tab: CSM Card Selected

Page 198: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 198/314

3EM23954ABIssue 01, February 2010

 Administer Network Configuration4-146

DLP-118

12 Select action.

To provision TMN Interface, go to step 13.

To deprovision TMN Interface, go to step 22.

Provision TMN Ethernet Interface

13 Select TMN Working Mode check box Enabled.

14 Enter IP Address in IP Address field.

15 Enter IP Mask or Netmask in IP Mask field.

16 Select IP Routing Protocol from drop-down menu.

 –  Static Routing.

 – OSPF

Figure 118-4. TMN Ethernet Interface: Settings Tab

Page 199: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 199/314

3EM23954ABIssue 01, February 2010

 Administer Network Configuration 4-147

DLP-118

17 OSPF IP Routing Protocol selected?

If yes, then go to step 18.

If no, go to step 19.

18 Select the OSPF Area Number from drop-down menu and select OSPF Area Number.

19 Click Apply.

20 Close slot #1 window.

21 Go to step 67.

Deprovision TMN Ethernet Interface

22 Select TMN Working Mode check box Enabled (unchecked).

23 Click Apply.

24 Close slot #1 window.

25 Go to step 67.

Administer Port#4 TMN Ethernet Interface

26 Select the MSS/Core-Main slot #1 in the Resource Tree area. The selected name will be

highlighted in yellow. This selection should also highlight the MSS/Core card in blue

Resource List Area.

27 Double left click the blue MSS/Core-Main (CSM) Card.

Page 200: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 200/314

3EM23954ABIssue 01, February 2010

 Administer Network Configuration4-148

DLP-118

Ethernet Physical Interface Settings Tab displays.

28 Select TMN Interface tab.

29 Select Port#4 TMN Ethernet in left frame.

30 Selecting Settings tab.

31 Select action.

To provision Port#4 TMN Ethernet Interface, go to step 32.

To deprovision Port#4 TMN Ethernet Interface, go to step 43.

Figure 118-5. 9500 MPR Equipment Tab: CSM Card Selected

Page 201: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 201/314

3EM23954ABIssue 01, February 2010

 Administer Network Configuration 4-149

DLP-118

Provision Port#4 TMN Ethernet Interface

Provision Port#4 TMN Ethernet Interface

32 Select TMN Working Mode Enabled check box.

33 Enter IP Address for Port#4 TMN Ethernet interface.

34 Enter IP Mask or Netmask.

35 Static or OSPF TMN interface routing?

If static, go to step 36.

If OSPF, go to step 38.

36 Select the IP Routing Protocol drop-down menu and select Static Routing.

Figure 118-6. Port#4 TMN Ethernet Interface: Settings Tab

Page 202: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 202/314

3EM23954ABIssue 01, February 2010

 Administer Network Configuration4-150

DLP-118

37 Go to step 40.

38 Select the IP Routing Protocol drop-down menu and choose OSPF.

39 Select the OSPF Area Number drop-down menu and choose OSPF Area Number(0 - 3).

40 Click Apply.

41 Close the slot #1 window.

42 Go to step 67.

Deprovision Port#4 TMN Ethernet Interface

43 Select TMN Working Mode check box Enabled (unchecked).

44 Click Apply.

45 Close slot #1 window.

46 Go to step 67.

Provision IP Static Routing

47 Select Configuration/Network Configuration/IP Configuration/IP Static Routing

Configuration.

The IP Static Routing Configuration window opens.

48 Select the desired Host or Network Address Choice radio button:

 – Host

 – Network

49 Which IP Static Routing Configuration was selected?

If Network, go to step 50.

If Host, go to step 51.

50 Enter the IP Mask of the radio in the IP Mask text field.

51 Enter the IP Address of the radio in the IP Address text field.

Page 203: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 203/314

3EM23954ABIssue 01, February 2010

 Administer Network Configuration 4-151

DLP-118

52 Select the desired Default Gateway or Point to Point I/F Choice radio button:

 – Default Gateway IP Address

 – Point To Point Interface Index

53 Which Default Gateway or Point to Point I/F Choice was selected?

If Default Gateway IP Address, go to step 54.

If Point To Point Interface Index, go to step 56.

54 Enter the Default Gateway IP Address in the Default Gateway IP Address text field.

55 Go to step 57.

56 From the Interface Type drop-down menu, select Gateway.

57 Click Create.

58 Click Close.

59 Go to step 67.

Provision OSPF Area Configuration

60 Select Configuration/Network Configuration/IP Configuration/OSPF Area Configuration.

The OSPF Area Configuration window opens.

61 Select the new check-box.

62 Enter the OSPF Area Address in the OSPF Area Address text field.

Figure 118-7. OSPF Area Configuration Path

Page 204: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 204/314

3EM23954ABIssue 01, February 2010

 Administer Network Configuration4-152

DLP-118

63 Select the desired OSPF Area Stub Flag  drop-down menu, select the desired OSPF

 Area Stub Flag value:

 – True

 – False

64 Click Create.

65 Click Apply.

66 Click Close.

67 STOP. This procedure is complete.

Page 205: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 205/314

3EM23954ABIssue 01, February 2010

 Administer System Date and Time 4-153

DLP-119

DLP-119

Administer System Date and Time

PURPOSE

This procedure is used to administer NE Date and Time.

GENERAL

The system NE Time can be set to the operating system (PC/laptop) or manually, or to a Network

Time Protocol (NTP) server to manage time and date stamping functions. Time and date

provisioning is accomplished using the NE Time Configuration screen.

The date format is yyyy/mm/dd, where yyyy equals the four digit year, mm equals the two digit

month, and dd equals the two digit day.

The time format is hh:mm:ss, where hh equals the two digit hour (00 - 23), mm equals the two digitminute (00 - 59), ss equals the two digit second (00 - 59).

Following an NE time change, PM history data must be cleared to prevent reporting erroneous PM

data.

The WebEML Craft Terminal Reference Guide in the back of this manual may also be used as

reference.

STEP PROCEDURE

1 Select action?

If set NE Time with PC Operating System Time, go to step 2.

If set NE Time manually, go to step 2.

If set NE Time with NTP server, go to step 14.

2 Select the Configuration/NE Time.

Page 206: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 206/314

3EM23954ABIssue 01, February 2010

 Administer System Date and Time4-154

DLP-119

The NE Time Configuration window opens.

3 Select action?

If set NE Time with PC Operating System Time, go to step 4.

If set NE Time manually, go to step 9.

Set NE Time to PC Operating System Time

4 Select Set NE Time with OS Time check box.

Figure 119-1. NE Time Configuration Drop-Down Menu

Figure 119-2. NE Time Configuration Window

Page 207: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 207/314

3EM23954ABIssue 01, February 2010

 Administer System Date and Time 4-155

DLP-119

5 Click Apply to save the changes.

The Information ‘Set NE time success!’ window opens.

6 Click OK .

7 Click Close.

8 Go to step 22.

Set NE Time Manually

9 Select the date and time element to set in the Network Element Time field and perform

one or more of the following:

a. Enter the four digit year yyyy.

b. Enter the two digit month mm.

c. Enter the two digit day dd.

d. Enter the two digit hour hh.

e. Enter the two digit minute mm.

f. Enter the two digit second ss.

10 Click Apply to save the changes.

The Information ‘Set NE time success!’ window opens.

11 Click OK .

12 Click Close.

13 Go to step 22.

Set NE Time with NTP Server 

14 Select the Configuration/Network Configuration/NTP Configuration.

Page 208: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 208/314

3EM23954ABIssue 01, February 2010

 Administer System Date and Time4-156

DLP-119

15 The NTP Configuration window opens.

16 Select Enable check-box in the NTP Protocol field.

17 Enter Main Server address.

18 Enter Spare Server address if desired.

Figure 119-3. NTP Configuration Drop-Down Menu

Figure 119-4. NTP Configuration Window

Page 209: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 209/314

3EM23954ABIssue 01, February 2010

 Administer System Date and Time 4-157

DLP-119

19 Click Apply.

The Information ‘Set NTP Server success!’ window opens.

20 Click OK .

21 Click Close.

22 STOP. This procedure is complete.

Page 210: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 210/314

3EM23954ABIssue 01, February 2010

 Administer System Date and Time4-158

DLP-119

Page 211: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 211/314

3EM23954ABIssue 01, February 2010

 Administer Software License 4-159

DLP-120

DLP-120

Administer Software License

PURPOSE

This procedure provides the instructions to update and view Software License for the 9500 MPR.

STEP PROCEDURE

1 Select Supervision/SW License.

The SW License window opens.

Figure 120-1. Supervision SW License Path

Page 212: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 212/314

3EM23954ABIssue 01, February 2010

 Administer Software License4-160

DLP-120

2 Select action?

To view Software License, go to step 3.

To Update Software License, go to step 6.

View SW License

3  View software License Key, License String, and RMU Serial Number.

4 Click Close.

5 Go to step 11.

Update SW License

6 Open new software license text file.

7 Select new software License Key from text file and copy.

8 Select old software License Key in the SW License window and paste new software

License Key.

Figure 120-2. SW License Window

Page 213: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 213/314

3EM23954ABIssue 01, February 2010

 Administer Software License 4-161

DLP-120

9 Click Apply.

10 Click Close.

11 STOP. This procedure is complete.

Page 214: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 214/314

3EM23954ABIssue 01, February 2010

 Administer Software License4-162

DLP-120

Page 215: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 215/314

3EM23954ABIssue 01, February 2010

Perform Protection Switching 4-163

DLP-121

DLP-121

Perform Protection Switching

PURPOSE

This procedure provides the instructions to perform Protection Switching for the 9500 MPR.

CAUTION: Possibility of service interruption. Protection switching traffic will cause a hit to traffic.

STEP PROCEDURE

1 Select Protection Schemes Tab.

The Protection Schemes window opens. See Figure 121-1.

2 Select action?

To perform protection switching on CSM card, go to step 3.

To perform Equipment Protection switching, go to step 15.

Figure 121-1. Protection Schemes Tab

Page 216: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 216/314

3EM23954ABIssue 01, February 2010

Perform Protection Switching4-164

DLP-121

To perform HSB Protection switching, go to step 39.

To perform Rx Radio Protection switching, go to step 63.

Protection Switching on CSM Card

3 Select action?

To perform Forced Switch from Main CSM card to Spare CSM card, go

to step 4.

To perform Lockout of Spare CSM card, go to step 10.

Forced Switch Main CSM to Spare CSM

4 Select Main CSM card in the Resource Tree area. See Figure 121-2.

5 On the Commands tab, select Forced in the New Value drop-down menu.

6 CAUTION: Possibility of service interruption. Forced switching CSM will cause a hit

to traffic.

7 Click Apply.

The Switch confirmation window displays.

8 Click OK .

Page 217: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 217/314

3EM23954ABIssue 01, February 2010

Perform Protection Switching 4-165

DLP-121

9 Go to step 86.

Lockout Spare CSM Card

10 Select Spare CSM card in the Resource Tree area. See Figure 121-3.

11 On the Commands tab, select Lockout in the New Value drop-down menu.

12 Click Apply.

The Switch confirmation window displays.

13 Click OK .

Figure 121-2. Forced Switch Main CSM to Spare CSM

Page 218: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 218/314

3EM23954ABIssue 01, February 2010

Perform Protection Switching4-166

DLP-121

14 Go to step 86.

Equipment Protection

15 Select action?

To perform Forced Switch from Main to Spare, go to step 16.

To perform Manual Switch from Main to Spare, go to step 22.

To perform Manual Switch from Spare to Main, go to step 28.

To perform Lockout Switch of Spare, go to step 34.

16 Select Protection Schemes/Slot#/Equipment Protection/Main # in the Resource Tree

area. See Figure 121-4.

17 CAUTION: Possibility of service interruption. Forced EPS switching equipment will

cause a hit to traffic.

18 On the Commands tab, select Forced in the New Value drop-down menu.

19 Click Apply.

The Switch confirmation window displays.

Figure 121-3. Lockout Spare CSM Card

Page 219: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 219/314

3EM23954ABIssue 01, February 2010

Perform Protection Switching 4-167

DLP-121

20 Click OK .

21 Go to step 86.

Equipment Protection: Manual Switch Main to Spare

22 Select Protection Schemes/Slot#/Equipment Protection/Main # in the Resource Tree

area. See Figure 121-5.

23 CAUTION: Possibility of service interruption. Manual EPS switching equipment will

cause a hit to traffic.

24 On the Commands tab, select Manual in the New Value drop-down menu.

25 Click Apply.

The Switch confirmation window displays.

26 Click OK .

Figure 121-4. Forced Equipment Switch Main to Spare

Page 220: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 220/314

3EM23954ABIssue 01, February 2010

Perform Protection Switching4-168

DLP-121

27 Go to step 86.

Equipment Protection: Manual Switch Spare to Main

28 Select Protection Schemes/Slot#/Equipment Protection/Main # in the Resource Tree

area. See Figure 121-6.

29 CAUTION: Possibility of service interruption. Manual EPS switching equipment will

cause a hit to traffic.

30 On the Commands tab, select Manual in the New Value drop-down menu.

31 Click Apply.

The Switch confirmation window displays.

32 Click OK .

Figure 121-5. Manual Equipment Switch: Main to Spare

Page 221: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 221/314

3EM23954ABIssue 01, February 2010

Perform Protection Switching 4-169

DLP-121

33 Go to step 86.

Equipment Protection: Lockout Spare

34 Select Protection Schemes/Slot#/Equipment Protection/Main # in the Resource Tree

area. See Figure 121-7.

35 On the Commands tab, select Lockout in the New Value drop-down menu.

36 Click Apply.

The Switch confirmation window displays.

37 Click OK .

Figure 121-6. Manual Equipment Switch: Spare to Main

Page 222: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 222/314

3EM23954ABIssue 01, February 2010

Perform Protection Switching4-170

DLP-121

38 Go to step 86.

Hot StandBy Protection Switching

39 Select action?

To perform Forced Switch from Main to Spare, go to step 40.

To perform Manual Switch from Main to Spare, go to step 46.

To perform Manual Switch from Spare to Main, go to step 52.

To perform Lockout Switch of Spare, go to step 58.

HSB Protection: Forced Switch Main Radio Channel to Spare Radio Channel

40 Select Protection Schemes/Slot#/HSB Protection/Main # in the Resource Tree area.

See Figure 121-8.

41 CAUTION: Possibility of service interruption. Forced HSB switching equipment will

cause a hit to traffic.

42 On the Commands tab, select Forced in the New Value drop-down menu.

Figure 121-7. Lockout Equipment Switch: Lockout Switch to Spare

Page 223: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 223/314

3EM23954ABIssue 01, February 2010

Perform Protection Switching 4-171

DLP-121

43 Click Apply.

The Switch confirmation window displays.

44 Click OK .

45 Go to step 86.

HSB Protection: Manual Switch Main Radio Channel to Spare Radio Channel

46 Select Protection Schemes/Slot#/HSB Protection/Main # in the Resource Tree area.

See Figure 121-9.

47 CAUTION: Possibility of service interruption. Manual HSB switching equipment willcause a hit to traffic.

48 On the Commands tab, select Manual in the New Value drop-down menu.

49 Click Apply.

The Switch confirmation window displays.

Figure 121-8. Forced HSB Switch Main Radio Channel to Spare Radio Channel

Page 224: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 224/314

3EM23954ABIssue 01, February 2010

Perform Protection Switching4-172

DLP-121

50 Click OK .

51 Go to step 86.

HSB Protection: Manual Switch Spare Radio Channel to Main Radio Channel

52 Select Protection Schemes/Slot#/HSB Protection/Spare # in the Resource Tree area.

See Figure 121-10.

53 CAUTION: Possibility of service interruption. Manual HSB switching equipment will

cause a hit to traffic.

54 On the Commands tab, select Manual in the New Value drop-down menu.

55 Click Apply.

The Switch confirmation window displays.

56 Click OK .

Figure 121-9. Manual HSB Switch: Main Radio Channel to Spare Radio Channel

Page 225: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 225/314

3EM23954ABIssue 01, February 2010

Perform Protection Switching 4-173

DLP-121

57 Go to step 86.

HSB Protection: Lockout Spare Radio Channel

58 Select Protection Schemes/Slot#/HSB Protection/Spare # in the Resource Tree area.

See Figure 121-11.

59 On the Commands tab, select Lockout in the New Value drop-down menu.

60 Click Apply.

The Switch confirmation window displays.

61 Click OK .

Figure 121-10. Manual HSB Switch: Spare Radio Channel to Main Radio Channel

Page 226: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 226/314

3EM23954ABIssue 01, February 2010

Perform Protection Switching4-174

DLP-121

62 Go to step 86.

Rx Radio Protection Switching

63 Select action?

To perform Forced Switch from Main to Spare, go to step 64.

To perform Manual Switch from Main to Spare, go to step 70.

To perform Manual Switch from Spare to Main, go to step 76.

To perform Lockout Switch of Spare, go to step 82.

Rx Radio Protection: Forced Switch Main Radio Channel to Spare Radio Channel

64 Select Protection Schemes/Slot#/Rx Radio Protection/Main # in the Resource Tree

area. See Figure 121-12.

65 CAUTION: Possibility of service interruption. Forced Rx Radio switching equipment

will cause a hit to traffic.

66 On the Commands tab, select Forced in the New Value drop-down menu.

Figure 121-11. Lockout HSB Switch: Lockout Spare Radio Channel

Page 227: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 227/314

3EM23954ABIssue 01, February 2010

Perform Protection Switching 4-175

DLP-121

67 Click Apply.

The Switch confirmation window displays.

68 Click OK .

69 Go to step 86.

Rx Radio Protection: Manual Switch Main Radio Channel to Spare Radio Channel

70 Select Protection Schemes/Slot#/Rx Radio Protection/Main # in the Resource Tree

area. See Figure 121-13.

71 CAUTION: Possibility of service interruption. Manual Rx Radio switching equipmentwill cause a hit to traffic.

72 On the Commands tab, select Manual in the New Value drop-down menu.

73 Click Apply.

The Switch confirmation window displays.

Figure 121-12. Forced Rx Radio Switch: Main Radio Channel to Spare Radio Channel

Page 228: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 228/314

3EM23954ABIssue 01, February 2010

Perform Protection Switching4-176

DLP-121

74 Click OK .

75 Go to step 86.

Rx Radio Protection: Manual Switch Spare Radio Channel to Main Radio Channel

76 Select Protection Schemes/Slot#/Rx Radio Protection/Spare # in the Resource Tree

area. See Figure 121-14.

77 CAUTION: Possibility of service interruption. Manual Rx Radio switching equipment

will cause a hit to traffic.

78 On the Commands tab, select Manual in the New Value drop-down menu.

79 Click Apply.

The Switch confirmation window displays.

80 Click OK .

Figure 121-13. Manual Rx Radio Switch: Main Radio Channel to Spare Radio Channel

Page 229: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 229/314

3EM23954ABIssue 01, February 2010

Perform Protection Switching 4-177

DLP-121

81 Go to step 86.

Rx Radio Protection: Lockout Spare Radio Channel

82 Select Protection Schemes/Slot#/Rx Radio Protection/Spare # in the Resource Tree

area. See Figure 121-15.

83 On the Commands tab, select Lockout in the New Value drop-down menu.

84 Click Apply.

The Switch confirmation window displays.

85 Click OK .

Figure 121-14. Manual Rx Radio Switch: Spare Radio Channel to Main Radio Channel

Page 230: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 230/314

3EM23954ABIssue 01, February 2010

Perform Protection Switching4-178

DLP-121

86 STOP. This procedure is complete.

Figure 121-15. Lockout Rx Radio Switch Spare Radio Channel

Page 231: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 231/314

3EM23954ABIssue 01, February 2010

Performance Monitoring 4-179

DLP-122

DLP-122

Performance Monitoring

PURPOSE

This procedure provides the instructions to configure and perform Performance Monitoring (PM) for

the 9500 MPR.

GENERAL

PM provides an indication of the quality of service for the Radio Hop Section and Link Hop Section.

Radio Hop Section and Link Hop Section are defined as follows:

•   Radio Hop Section—An unprotected radio channel (before Radio Protection

Switching in 1+1 radio configurations).

•   Link Hop Section—A protected radio channel (after Radio Protection Switching).Only supported in 1+1 radio configurations.

 Adaptive Modulation PM captures the modulation scheme used on the Tx side when adaptive

modulation is enabled. In 1+1 HSB radio configuration, the statistics are associated with the link

level after Radio Protection Switching. Adaptive Modulation PM is not supported in 1+1 FD radio

configurations.

Defect second for a radio hop section is a second with a LOF of DemFail occurrence.

Defect second for a Link hop section is a second with a LOF at the link level after Radio Protection

Switching.

Errored Block count for a radio hop section equals the number of errored block.

Errored Block count for a Link hop section equals the number of errored block at the link level after

Radio Protection Switching.

Four PM counters are supported as follows:

•   Errored Second (ES)—When a defect second is set or if there is at least one or more

errored blocks.

•   Severely Errored Seconds (SES)—When a defect second is set and if the errored

block count is greater or equal to 30% of the blocks in one second.

•   Background Block Error (BBE))—The number of block errors in a one second

period and the second is not a SES.

•   Unavailable Seconds (UAS)—A time period starting after ten consecutive SES

events are detected. The qualifying 10 consecutive SES seconds are included in

the UAS time period. Ending upon the detection of 10 consecutive non SES events.

These non SES seconds are not included in the UAS time period.

Page 232: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 232/314

3EM23954ABIssue 01, February 2010

Performance Monitoring4-180

DLP-122

PM data is collected for 15 minute and 24 hour time periods. One current register and ninety-six

history reports are available for 15 minute period. One current register and eight history reports are

available for 24 hour time period.

PM data is considered suspect when one or more of the following conditions occurs during the

collection period.

•   The elapsed time deviates more than 10/900 seconds of the nominal time for 15

minute and 24 hour collection period.

•   Loss of PM data in equipment

•   Performance counters were reset during collection period.

•   PM was activated during the collection period.

The 15 minute PM data is stored in the History Data report only when errors are recorded.

The 24 hour PM data is always stored in the History Data report.

Threshold Crossing Alarm (TCA) thresholds are provisionable from the PM window. Two default

TCA threshold data tables are provided. One for 15 minute TCAs and one for 24 hour TCAs. Two

additional TCA threshold data tables are provisionable for both 15 minute TCAs and 24 hour TCAs.

See figure 122-A  for default TCA thresholds values.

Following an NE time change, PM history data must be cleared to prevent reporting erroneous PM

history data.

STEP PROCEDURE

1 Double left click the blue MSS/Radio (MOD300) Card.

Table 122-A. Default TCA Threshold Alarm Values

TCA ALARM 15 MINUTE

LOW

15 MINUTE

HIGH

24 HOUR

LOW

15 MINUTE

HIGH

BBE 200 9000 0 48000

ES 20 180 0 1500

ESE 0 15 0 20

Page 233: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 233/314

3EM23954ABIssue 01, February 2010

Performance Monitoring 4-181

DLP-122

MSS Radio Main View window opens.

2 Select Performance Monitoring Tab.

MSS Radio Performance Monitoring Tab displays.

Figure 122-1. 9500 MPR Equipment Tab: MOD300 Card Selected

Page 234: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 234/314

3EM23954ABIssue 01, February 2010

Performance Monitoring4-182

DLP-122

3 Select action?

To create new TCA thresholds table, go to step 4.

To modify existing TCA threshold table values, go to step 11.

To delete existing TCA threshold table, go to step 15.

To start PM, go to step 18.

To view PM data, go to step 28.

To export PM history data, go to step 31.

Create New TCA Threshold Table

4 In the Resource Tree Area, select either Threshold Table HOP  or Threshold Table

LINK .

Figure 122-2. Performance Monitoring Window

Page 235: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 235/314

3EM23954ABIssue 01, February 2010

Performance Monitoring 4-183

DLP-122

5 In the Resource List Area, select either 15m (15 minute) or 24h (24 hour) radio button.

6 Enter the values for BBE (low and high).

7 Enter the values for ES (low and high).

8 Enter the values for SES (low and high).

9 Click Create.

Figure 122-3. Threshold Data Creation Pane

Page 236: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 236/314

3EM23954ABIssue 01, February 2010

Performance Monitoring4-184

DLP-122

10 Go to step 37.

Modify Existing TCA Threshold Table Values

11 In the Resource Tree Area, select existing Threshold #n to modify TCA threshold

values.

NOTE: Threshold Table HOP, Threshold #1 and #4 are default tables. Threshold Table LINK,

Threshold #1 and #3 are default tables. The default table values are not editable.

Figure 122-4. Threshold #2 Data Table Created

Page 237: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 237/314

3EM23954ABIssue 01, February 2010

Performance Monitoring 4-185

DLP-122

12 Enter the new value(s) for BBE (low and high), ES (low and high), and/or SES (low and

high).

13 Click Apply.

Figure 122-5. Threshold Data Table Selected for Modification

Page 238: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 238/314

3EM23954ABIssue 01, February 2010

Performance Monitoring4-186

DLP-122

14 Go to step 37.

Delete Existing TCA Threshold Table

15 In the Resource Tree Area, select existing Threshold #n to delete.

Figure 122-6. Threshold Data Table Modified

Page 239: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 239/314

Page 240: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 240/314

3EM23954ABIssue 01, February 2010

Performance Monitoring4-188

DLP-122

17 Go to step 37.

Start Performance Monitoring

18 In the Resource Tree Area, select desired HOP - Channel #n or LINK .

Figure 122-8. Threshold Data Table Deleted

Page 241: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 241/314

3EM23954ABIssue 01, February 2010

Performance Monitoring 4-189

DLP-122

19 In the Resource List Area, select Counter Thresholds for 15m (15 minutes).

20 Click Apply.

21 In the Resource List Area, select Counter Thresholds 24h (24 hour).

22 Click Apply.

23 In the Resource Tree Area, select HOP - Channel #n CD 15m or LINK CD 15m.

24 Click Start.

25 In the Resource Tree Area, select HOP - Channel #n CD 24h or LINK CD 24h.

26 Click Start.

Figure 122-9. PM HOP - Channel #0 Selected

Page 242: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 242/314

3EM23954ABIssue 01, February 2010

Performance Monitoring4-190

DLP-122

27 Go to step 37.

View Performance Monitoring Data

28 In the Resource Tree Area, select HOP - Channel #n or LINK CD/HD 15m/24h to

view PM data.

Figure 122-10. PM HOP-Channel #0 Current Data 15 Minute Selected

Page 243: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 243/314

3EM23954ABIssue 01, February 2010

Performance Monitoring 4-191

DLP-122

29 Click Refresh.

Figure 122-11. PM Data HOP-Channel #0 Current Data 15 Minute Selected

Page 244: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 244/314

3EM23954ABIssue 01, February 2010

Performance Monitoring4-192

DLP-122

30 Go to step 37.

Export Performance Monitoring History Data

31 In the Resource Tree Area, select HOP - Channel #n or LINK HD 15m/24h to export

PM data.

Figure 122-12. PM Data HOP-Channel #1 History Data 15 Minute Selected

Page 245: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 245/314

3EM23954ABIssue 01, February 2010

Performance Monitoring 4-193

DLP-122

32 Click Export.

The Save dialog box opens.

33 Navigate to the directory to save PM History Data.

34 Enter the File Name to save PM History Data.

35 Click Save.

The Message dialog box opens.

36 Click OK.

37 STOP. This procedure is complete..

Figure 122-13. PM Data HOP-Channel #1 History Data 15 Minute Selected

Page 246: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 246/314

3EM23954ABIssue 01, February 2010

Performance Monitoring4-194

DLP-122

Page 247: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 247/314

3EM23954ABIssue 01, February 2010

Perform Radio Power Measurements 4-195

DLP-123

DLP-123

Perform Radio Power Measurements

PURPOSE

This procedure provides the instructions to perform Radio Power Measurements for the 9500 MPR.

STEP PROCEDURE

1 In the main equipment window, double left click the MOD300 card to perform radio

power measurements. See Figure 123-1.

The main view for the selected radio direction opens.

2 Select Measurements tab. See Figure 123-2.

3 Select Channel # to perform power measurements.

Figure 123-1. Main Equipment Window: MOD300 Card Highlighted

Page 248: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 248/314

3EM23954ABIssue 01, February 2010

Perform Radio Power Measurements4-196

DLP-123

4 Enter the Measurement Interval.

5 From the Sample Time (sec) drop-down menu, select the sample time.

6 Click Start.

The radio power measurement graphical view opens. See figure 123-3.

The radio power measurement tabular view opens. See figure 123-4.

Figure 123-2. Radio Power Measurement Window

Page 249: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 249/314

3EM23954ABIssue 01, February 2010

Perform Radio Power Measurements 4-197

DLP-123

Figure 123-3. Radio Power Measurement: Graphical View

Page 250: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 250/314

3EM23954ABIssue 01, February 2010

Perform Radio Power Measurements4-198

DLP-123

7 Click Close.

8 STOP. This procedure is complete.

Figure 123-4. Radio Power Measurement: Tabular View

Page 251: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 251/314

3EM23954ABIssue 01, February 2010

Deprovision Cross Connections 4-199

DLP-126

DLP-126

Deprovision Cross Connections

PURPOSE

This procedure is used to deprovision cross connections.

GENERAL

STEP PROCEDURE

1 Select Configuration/Cross Connections.

The Cross Connections window opens. See figure 126-1.

Figure 126-1. Cross Connection Window

Page 252: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 252/314

3EM23954ABIssue 01, February 2010

Deprovision Cross Connections4-200

DLP-126

2 Select Action?

If PDH to Radio (TDM2ETH), then go to step 3.

If PDH to Ethernet (TDM2ETH), then go to step 8.

If Ethernet to Radio (TDM2ETH), then go to step 13.

If Radio to Radio, then go to step 18.

Deprovision PDH to Radio Cross Connect

3 Double left-click PDH to RADIO line.

PDH-RADIO pop-up displays. See figure 126-2.

4 On the PDH_RADIO pop-up, select check box (unchecked) all Flow ID numbers of

cross connects to be deprovisioned.

5 On the PDH_RADIO pop-up, click OK.

6 On the Cross Connection screen, click Apply.

Figure 126-2. PDH-RADIO Cross Connection

Page 253: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 253/314

3EM23954ABIssue 01, February 2010

Deprovision Cross Connections 4-201

DLP-126

7 Go to step 22.

Deprovision PDH to Ethernet Cross Connection

8 Double left-click PDH port to Eth port line.

PDH-Eth pop-up displays. See figure 126-3.

9 On the PDH-Eth pop-up, select check box (unchecked) all Flow ID numbers of cross

connects to be deprovisioned.

10 On the PDH-ETH pop-up, click OK.

11 On the Cross Connection screen, click Apply.

12 Go to step 22.

Figure 126-3. PDH to Ethernet Cross Connection

Page 254: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 254/314

3EM23954ABIssue 01, February 2010

Deprovision Cross Connections4-202

DLP-126

Deprovision Ethernet to Radio Cross Connection

13 Double left-click ETH port to Radio port line.

RADIO-ETH pop-up displays. See figure 126-4.

14 On the RADIO-ETH pop-up, select check box (unchecked) Flow ID number of cross

connect to be deprovisioned.

15 On the RADIO-ETH pop-up, click OK.

16 On the Cross Connection screen, click Apply.

17 Go to step 22.

Figure 126-4. Ethernet to Radio Cross Connection

Page 255: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 255/314

3EM23954ABIssue 01, February 2010

Deprovision Cross Connections 4-203

DLP-126

Deprovision Radio to Radio Cross Connection

18 Double left-click Radio port to Radio port line.

RADIO-RADIO pop-up displays. See figure 126-5.

19 On the RADIO-RADIO pop-up, select check box (unchecked) Flow ID number of cross

connect to be deprovisioned.

20 On the RADIO-RADIO pop-up, click OK.

21 On the Cross Connection screen, click Apply.

22 STOP. This procedure is complete.

Figure 126-5. Radio to Radio Cross Connection

Page 256: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 256/314

3EM23954ABIssue 01, February 2010

Deprovision Cross Connections4-204

DLP-126

Page 257: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 257/314

3EM23954ABIssue 01, February 2010

Deprovision Ethernet Ports 4-205

DLP-127

DLP-127

Deprovision Ethernet Ports

PURPOSE

This procedure is used to deprovision Ethernet ports.

STEP PROCEDURE

1 Select action.

To deprovision CSM 10/100/1000 BaseT Ethernet Interfaces, go to

step 2.

To deprovision CSM Ethernet SFP Interface, go to step 11.

Deprovision Physical CSM Ethernet Interfaces

10/100/1000 Base T Ethernet Interfaces

2 Select the MSS/Core-Main slot #1 in the Resource Tree area. The selected name will be

highlighted in yellow. This selection should also highlight the MSS/Core card in blue

Resource List Area. See figure 127-1.

3 Double left click the blue MSS/Core-Main (CSM) Card and the Settings Tab for the

Ethernet Physical Interface will display.

Page 258: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 258/314

3EM23954ABIssue 01, February 2010

Deprovision Ethernet Ports4-206

DLP-127

Ethernet Physical Interface Tab will display.

4 Select Ethernet Physical Interface tab.

5 Select Ethernet Port number to deprovision (Ethernet Port #1/#4 ).

6 Selecting Settings tab. See figure 127-2.

Figure 127-1. 9500 MPR Equipment Tab: CSM Card Selected

Page 259: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 259/314

3EM23954ABIssue 01, February 2010

Deprovision Ethernet Ports 4-207

DLP-127

7 Enable Port Status, select enabled [unchecked].

8 Click Port Status Apply.

9 Close slot #1 window.

10 Go to step 19.

Deprovision CSM Ethernet SFP Interface

11 Select the MSS/Core-Main slot #1 in the Resource Tree area. The selected name will be

highlighted in yellow. This selection should also highlight the MSS/Core card in blue

Resource List Area. See figure 127-3.

Figure 127-2. CSM Ethernet Physical Interface: Settings Tab

Page 260: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 260/314

3EM23954ABIssue 01, February 2010

Deprovision Ethernet Ports4-208

DLP-127

12 Double left click the blue MSS/Core-Main (CSM) Card.

Ethernet Physical Interface Settings Tab will display. See figure 127-4.

Figure 127-3. 9500 MPR Equipment Tab: CSM Card Selected

Page 261: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 261/314

3EM23954ABIssue 01, February 2010

Deprovision Ethernet Ports 4-209

DLP-127

13 Select Ethernet Physical Interface tab.

14 Select Ethernet Port number #5 .

15 Selecting Settings tab. See figure 127-4.

16 Enable Port Status, select Enabled [unchecked].

17 Click Port Status Apply.

18 Go to step 19.

19 STOP. This procedure is complete.

Figure 127-4. CSM Ethernet Physical Interface: SFP Settings Tab

Page 262: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 262/314

3EM23954ABIssue 01, February 2010

Deprovision Ethernet Ports4-210

DLP-127

Page 263: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 263/314

3EM23954ABIssue 01, February 2010

 Administer NE Lists 4-211

DLP-128

DLP-128

Administer NE Lists

PURPOSE

This procedure provides instructions to create an NE list, add NEs to the NE list, and how to log into

an NE using the NE list.

PREREQUISITE

The Username and current Password must be known before login can be accomplished. 9500 MPR-A

CT R01.02 - Craft Terminal (CT) software must be installed on the PC. The user must know the IP

address of the NE to log into the system or be locally connected.

GENERAL

The 9500 MPR provides support for the Craft Terminal (CT) or WebEML (JUSM/CT) function,allowing NE management through a web-enabled PC.

The NE is accessed using the Network ElemenT Overview (NETO) application.

The WebEML Craft Terminal Reference Guide in the back of this manual may also be used as

reference.

STEP PROCEDURE

1 Select action?

If create new NE list, go to step 2.

If add NE to list, go to step 7.

If log into NE from list, go to step 20.

Create NE List

2 From the NETO login screen, select the Creates a new list of favorite NEs icon. See

Figure 128-1.

Page 264: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 264/314

3EM23954ABIssue 01, February 2010

 Administer NE Lists4-212

DLP-128

The Network Element List window opens. See Figure 128-2.

3 Click Save.

The Save window opens. See Figure 128-3.

Figure 128-1. NETO Overview Window

Figure 128-2. Network Elements List Window

Page 265: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 265/314

3EM23954ABIssue 01, February 2010

 Administer NE Lists 4-213

DLP-128

4 In the File Name field, type the desired name of the NE list: <NE_List_Name>

5 Click Save.

The Filed saved window opens.

6 Click OK.

The Network Elements List window opens. See Figure 128-4.

Figure 128-3. NE List Save Window

Page 266: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 266/314

3EM23954ABIssue 01, February 2010

 Administer NE Lists4-214

DLP-128

Add NE to List

7 Select action?

If add NE by first logging into the NE, go to step 8.

If add NE by entering NE IP address into Network Elements List

window, go to step 14.

Add NE to List by First Logging into the NE

8 From the NETO login window, log into the NE to add to the NE list.

9 From the Network Elements List window, click Get Current. See Figure 128-5.

The NE currently logged into is added to the NEs table.

Figure 128-4. Network Elements List Window

Page 267: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 267/314

3EM23954ABIssue 01, February 2010

 Administer NE Lists 4-215

DLP-128

10 Click Save.

File already existing. Overwrite? window opens.

11 Click Yes.

File saved window opens.

12 Click OK.

13 Go to step 35.

Add NE to List by Entering NE IP Address

14 Click New. See Figure 128-6.

15 In the table row just added, type the NE IP address in the IP/DNS column and hit

Enter .

Figure 128-5. Network Elements List Window: Current NE Added

Page 268: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 268/314

3EM23954ABIssue 01, February 2010

 Administer NE Lists4-216

DLP-128

16 Click Save.

Save window opens.File already existing. Overwrite? window opens.

17 Click Yes.

File saved window opens.

18 Click OK.

19 Go to step 35.

Log into NE From NE List

20 Select action?

If open NE by opening a file containing a list of NEs, go to step 21.

If open NE from current file containing a list of NEs, go to step 29.

Open NE From Saved List of NEs

21 From the NETO Login window, click the Opens a file containing a list of favorite NEs. 

icon. See Figure 128-7.

Figure 128-6. Network Elements List Window

Page 269: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 269/314

3EM23954ABIssue 01, February 2010

 Administer NE Lists 4-217

DLP-128

Open window opens. See Figure 128-8.

Figure 128-7. NETO Overview Window

Figure 128-8. Open Window

Page 270: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 270/314

3EM23954ABIssue 01, February 2010

 Administer NE Lists4-218

DLP-128

22 Select the NE List file name <NE_List.neto>, then click Open.

Network Elements List window opens. See Figure 128-9.

23 Select the NE from the NEs table and click Set Current.

The NETO Login window opens. See Figure 128-10.

Figure 128-9. Network ElemenT List Window

Figure 128-10. NETO Overview Window

Page 271: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 271/314

3EM23954ABIssue 01, February 2010

 Administer NE Lists 4-219

DLP-128

24 Click OK.

25 Click Show.

26 In the Login window, enter UserName “username” and Password “ password”.

27 Click Apply.

JUSM 9500MPR window launches. See Figure 128-11.

28 Go to step 35.

Open NE From Current List of NEs

29 From the NETO Login window, click the Opens the current list of favorite NEs. icon. See

Figure 128-12.

Figure 128-11. JUSM/CT 9500MPR-A Main Screen

Page 272: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 272/314

3EM23954ABIssue 01, February 2010

 Administer NE Lists4-220

DLP-128

Network Elements List window opens. See Figure 128-13.

30 Select the NE from the NEs Table and click Set Current.

The NETO Overview window opens. See Figure 128-14.

Figure 128-12. NETO Overview Window

Figure 128-13. Network ElemenT List Window

Page 273: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 273/314

3EM23954ABIssue 01, February 2010

 Administer NE Lists 4-221

DLP-128

31 Click OK.

32 Click Show.

33 In the Login window, enter UserName “username” and Password “ password”.

34 Click Apply.

JUSM 9500MPR window launches. See Figure 128-15.

Figure 128-14. NETO Overview Window

Page 274: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 274/314

3EM23954ABIssue 01, February 2010

 Administer NE Lists4-222

DLP-128

35 STOP. This procedure is complete.

Figure 128-15. JUSM/CT 9500MPR-A Main Screen

Page 275: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 275/314

Page 276: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 276/314

3EM23954ABIssue 01, February 2010

View Event Log4-224

DLP-129

2 Select action?

If export event log, go to step 3.If print event log, go to step 12.

Export Event Log

3 Select File/Export/Export Event.

Export Events window opens.

4 Select Output Format: HTML, CSV, PDF, or XML.

5Select What entries to you want to export: All Entries, or Selection.

6 Click OK.

Save window opens.

7 Navigate to the directory to save the Event Log.

Figure 129-2. Event Log Browser Window

Page 277: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 277/314

Page 278: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 278/314

Page 279: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 279/314

3EM23954ABIssue 01, February 2010

IF Cable Loopback 4-227

DLP-130

DLP-130

IF Cable Loopback

PURPOSE

This procedure provides the instructions to perform MOD300 card IF Cable Loopback for the

9500 MPR.

GENERAL

IF Cable Loopback is active only on the cross-connections associated with TDM2TDM and TDM2Eth

profiles. Loopback of Ethernet traffic is not supported.

IF Cable Loopback can be activated from the local NE only.

For a block diagram of IF Cable Loopback, see Figure 130-1.

STEP PROCEDURE

1 In the main equipment window, double left click the MOD300 card to perform IF cable

loopback. See Figure 130-2.

Figure 130-1. IF Cable Loopback Block Diagram

Page 280: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 280/314

3EM23954ABIssue 01, February 2010

IF Cable Loopback4-228

DLP-130

The MSS Radio Main View for the selected radio direction opens.

2 Select action?

If activate IF cable loopback, go to step 3.

If deactivate IF cable loopback, go to step 15.

Activate IF Cable Loopback

3 Select Settings tab. See Figure 130-5.

Figure 130-2. Main Equipment Window: MOD300 Card Highlighted

Page 281: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 281/314

3EM23954ABIssue 01, February 2010

IF Cable Loopback 4-229

DLP-130

4 Select TxMute Enable check-box.

5 Click Apply.

Tx Mute Settings dialog box displays.

6 Click Yes.

Command Summary dialog box displays.

7 Click OK.

Radio channel transmitter TxMute enabled. See Figure 130-4.

Figure 130-3. Radio Channel Settings Tab

Page 282: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 282/314

3EM23954ABIssue 01, February 2010

IF Cable Loopback4-230

DLP-130

8 Select Loopback tab. See Figure 130-5.

Figure 130-4. Transmitter TxMute Enabled

Page 283: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 283/314

3EM23954ABIssue 01, February 2010

IF Cable Loopback 4-231

DLP-130

9 Select IF Cable.

10 Select Active radio button.

11 In the Timeout Period (max 4 days) fields enter the IF cable loopback duration.

Figure 130-5. MOD300 IF Cable Loopback Window

Page 284: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 284/314

3EM23954ABIssue 01, February 2010

IF Cable Loopback4-232

DLP-130

12 Click Apply.

The Loopback Setting dialog box displays.

13 Click OK.

MOD300 IF cable loopback active. See figure 130-7.

Figure 130-6. MOD300 IF Cable Loopback Provisioned

Page 285: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 285/314

3EM23954ABIssue 01, February 2010

IF Cable Loopback 4-233

DLP-130

14 Go to step 23.

Deactivate IF Cable Loopback

15 Select Loopback tab. See Figure 130-8.

Figure 130-7. MOD300 IF Cable Loopback Active

Page 286: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 286/314

3EM23954ABIssue 01, February 2010

IF Cable Loopback4-234

DLP-130

16 Select IF Cable.

17 Select Not Active radio button. See figure 130-9.

Figure 130-8. MOD300 IF Cable Loopback Active

Page 287: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 287/314

3EM23954ABIssue 01, February 2010

IF Cable Loopback 4-235

DLP-130

18 Click Apply.

MOD300 IF cable loopback deactivated (Not active). See figure 130-10.

Figure 130-9. MOD300 IF Cable Loopback Active, Not Active Selected

Page 288: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 288/314

3EM23954ABIssue 01, February 2010

IF Cable Loopback4-236

DLP-130

19 Select Settings tab. See Figure 130-11.

Figure 130-10. MOD300 IF Cable Loopback Deactivated (Not Active)

Page 289: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 289/314

3EM23954ABIssue 01, February 2010

IF Cable Loopback 4-237

DLP-130

20 Select TxMute Enable check-box (unchecked).

21 Click Apply.

Command Summary dialog box displays.

22 Click OK.

Radio channel transmitter TxMute disabled. See Figure 130-12.

NOTE: Recommend waiting 25 seconds before executing another command after disabling

TxMute.

Figure 130-11. Settings Tab, Transmitter TxMute Enabled

Page 290: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 290/314

3EM23954ABIssue 01, February 2010

IF Cable Loopback4-238

DLP-130

23 STOP. This procedure is complete.

Figure 130-12. TxMute Disabled

Page 291: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 291/314

3EM23954ABIssue 01, February 2010

MIB Database Management (Backup and Restore) 4-239

DLP-131

DLP-131

MIB Database Management (Backup and Restore)

PURPOSE

This procedure provides the instructions to perform MIB Database Management (backup and

restore) on the 9500 MPR. MIB database restore should be performed for catastrophic recovery

ONLY.

GENERAL

CAUTION: Possibility of service interruption. ALL traffic will be interrupted during activate database

phase.

CAUTION: Possibility of service interruption. ALL traffic will be interrupted, upon completion of system

restart, the MSS-8 shelf must be power cycled to complete the database restore process.

The backup operation provides the ability to save a copy of NE configurations parameters stored on

the flash memory on the NE CSM Core card(s).

The restore operation provides the ability to restore a previously saved copy of NE configurations

parameters to the flash memory on the NE CSM Core card(s).

The following networking parameters are not saved during MIB Management Database Backup.

•   Local IP address provisioning

•   Local Ethernet Interface provisioning

•   Static routing provisioning

•   OSPF area provisioning

•   NTP configuration

•   PPP/RF configuration

•   Loopbacks

•   Manual protection switches

The above listed parameters are not affected during MIB Management Database Restore.

It is recommended that these parameters be saved by running a Current Configuration View report,

so these parameters may be reprovisioned in the event that the system needs to be restored from

scratch.

 After completing the restore operation, the restored database must be activated to apply the

downloaded parameters to the NE. Upon activation of the restored database, the NE will

automatically restart.

Page 292: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 292/314

3EM23954ABIssue 01, February 2010

MIB Database Management (Backup and Restore)4-240

DLP-131

Database backup should be performed with no forced protection switches active. A system restored

with a backup database that was saved while forced protection switches are active, may result in the

system being restored to an unknown state. If this occurs, communications with the system may be

difficult to reestablish and may result in the loss of traffic.

STEP PROCEDURE

1 Select the Protection Schemes tab.

2  Verify no forced protection switches are active.

3  Are forced protection switches active?

If yes, go to step 4.

If no, go to step 6.

4 CAUTION: Possibility of service interruption. Failure to release ALL protection switches

prior to performing a MIB Management database backup, may result in the system being

restored to an unknown state. If this occurs, communications with the system may be

difficult to reestablish and may result in the loss of traffic.

5 Determine if the active forced protection switch(es) can be released. Release ALL

forced protection switch(es) prior to proceeding with this procedure.

6 Select action?

If backup MIB Management database, go to step 7.

If restore MIB Management database, go to step 15.

If activate restored MIB Management database, go to step 23.

Backup MIB Management Database

7 Save current configuration data. Refer to DLP-116 for detailed instructions to view

and save current configuration data.

8 In the main Menu bar, select Supervision>MIB Management>Backup. See Figure 131-1.

Page 293: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 293/314

3EM23954ABIssue 01, February 2010

MIB Database Management (Backup and Restore) 4-241

DLP-131

The Backup window opens. See Figure 131-2.

9 Navigate to the directory to save MIB Management Database.

10 Enter the file name of the MIB Management Database backup file in the File Name 

field.

11 Click Save.

Backup confirmation window opens.

Figure 131-1. Backup MIB Management Database Path

Figure 131-2. Backup MIB Management Database Dialog Box

Page 294: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 294/314

3EM23954ABIssue 01, February 2010

MIB Database Management (Backup and Restore)4-242

DLP-131

12 Click Yes.

MIB Management window opens.

13 Click OK.

14 Go to step 34.

Restore MIB Management Database

15 In the main Menu bar, select Supervision>MIB Management>Restore. See

Figure 131-3.

The Restore window opens. See Figure 131-4.

Figure 131-3. Restore MIB Management Database Path

Page 295: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 295/314

3EM23954ABIssue 01, February 2010

MIB Database Management (Backup and Restore) 4-243

DLP-131

16 Navigate to the directory where the MIB Management Database backup file is saved.

17 Select the MIB Management Database backup file.

18 Click Open.

Restore confirmation window opens.

19 Click Yes.

MIB Management window opens.

20  Activate restored MIB Management Database?

If yes, go to step 24.

If no, go to step 21.

21 Click No.

22 Go to step 34.

Activate Restored MIB Management Database

23 In the main Menu bar, select Supervision>MIB Management>Activate. See

Figure 131-5.

Figure 131-4. Restore MIB Management Database Window

Page 296: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 296/314

3EM23954ABIssue 01, February 2010

MIB Database Management (Backup and Restore)4-244

DLP-131

The Activate confirmation window opens.

24 CAUTION: Possibility of service interruption. ALL traffic will be interrupted during activate

database.

25 Click Yes.

MIB Management window opens.

26 Click OK.

27 Close the WebEML window.

The NE will activate the restored MIB Management database. There may be a delay

of 60 to 90 seconds before the Activate process begins. The NE will automatically

restart. A loss communication with the NE will occur. Do not attempt any WebEML

activates until the NE has completed restarting. Once the craft realigns with the NE,

it is OK to log in to the system. Restarting the NE can take up to 10 minutes to

complete.

NOTE: Because MIB database restore does not affect local IP address provisioning, it will

be necessary to connect to the MSS-8 shelf using the same IP address used prior to

database restore. If no IP address provisioning was performed prior to MIB database restore

it will be necessary to connect to the MSS-8 shelf using the default IP address (10.0.1.2) and

the main TMN port.

28 CAUTION: Possibility of service interruption. ALL traffic will be interrupted, upon

completion of system restart, the MSS-8 shelf must be power cycled to complete thedatabase restore procedure.

29 Power cycle the MSS-8 shelf. Remove the fuses in the PDU supplying power to the

MSS-8 shelf.

30 Wait 15 seconds, install fuses in the PDU supplying power to the MSS-8 shelf.

Figure 131-5. Activate MIB Management Database Path

Page 297: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 297/314

3EM23954ABIssue 01, February 2010

MIB Database Management (Backup and Restore) 4-245

DLP-131

31 Once the system restarts and the craft is able to connect, log into the NE.

32  Verify system provisioning. Refer to the saved current configuration view, saved

during the MIB backup procedure.

33 Provision any required settings that are not restored as part of the backup/restore

process (e.g. IP address, NTP, etc.).

34 STOP. This procedure is complete.

Page 298: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 298/314

3EM23954ABIssue 01, February 2010

MIB Database Management (Backup and Restore)4-246

DLP-131

Page 299: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 299/314

3EM23954ABIssue 01, February 2010

Load System and Craft Terminal Software on PC 4-247

DLP-132

DLP-132

Load System and Craft Terminal Software on PC

PURPOSE

This procedure is used to install 9500 MPR software.

GENERAL

Software Kit

Software Kit is delivered with each 9500 MPR. The software kit consists of the following three

CD-ROMs:

•   9500MPR-A CT R01.02.00 - Craft Terminal (CT) software - hereafter called

WebEML (JUSM/CT) - installed on the PC at initial Turn-Up

•   9500MPR-A SWP R01.02.00- radio application software - not required for initial

Turn-Up - hereafter called SWP

•   v4.04.01 MIB - SNMP MIB software - not required for initial Turn-Up - hereafter

called MIB

The SWP and MIB software is downloaded on the NE flash card and the flash card is installed on

the CSM (Control and Switching Module) at the factory. It is not necessary to install SWP and MIB

software on the PC at initial Turn-Up. The SWP CD is supplied with the equipment for backup. The

MIB CD is supplied for use by third-party SNMP applications.

Flash Card

The flash card consists of:

•   License Key

•   MAC Address

•   SW Load

PC Characteristics

The PC for Craft Terminal applications must meet following characteristics:

Page 300: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 300/314

3EM23954ABIssue 01, February 2010

Load System and Craft Terminal Software on PC4-248

DLP-132

PC HW Configuration:

•   CPU: Pentium III 850 MHz

•   RAM: 512 Mbytes (minimum), 1 Gbyte (suggested)

•   Min. disk space: 1.5 Gbyte's (available space needed, JRE excluded)

•   Min. resolution: equal or higher than 1024x768 pixel

•   CD-ROM Drive: 24x

•   Primary Interface: Ethernet Card 10/100 Mbits/sec.

Operating Systems Supported:

•   Microsoft Windows 32-bit versions: Microsoft Windows XP Professional service

pack 2 or Microsoft Windows Vista Business

 Additional requirements:

•   Microsoft Internet Explorer 6.0 6.02900.2180 SP1+ or higher or Microsoft

Internet Explorer 7.0.5730.11CO + or higher or Firefox 2.x Win32

•   Administrator or Power User rights

•   Java Runtime Environment (JRE) 6 Update 3 (Available on the CT CD-ROM)

There is no checklist for this procedure.

REQUIRED EQUIPMENT

Software Kit, Alcatel-Lucent PN: 3EM23052ADAA 

Flash Card, Alcatel-Lucent PN: 3EM23055ADAA 

RJ-45 Cat5E cable, Straight-through, Alcatel-Lucent PN:3EM15052xx

STEP PROCEDURE

1 Craft PC require a protective firewall?

If yes, go to step 2.

If no, go to step 21.

Configure Windows Firewall

The following procedure configures the PC to allow the CT to run on the PC with

Windows Firewall. The steps are specific for Windows XP SP2. Steps for Windows

 Vista are similar.

Page 301: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 301/314

3EM23954ABIssue 01, February 2010

Load System and Craft Terminal Software on PC 4-249

DLP-132

2 Open the Windows Firewall Settings Dialog: Start-Settings-Control Panel-Windows

Firewall.

3 Select On (recommended) to enable firewall.

4 Ensure the Don’t allow exceptions box is unchecked.

NOTE: If you are unable to make changes to this setting (e.g. The setting is grayed

out/disabled), your computer or network security policy may not allow you to make changes.

Contact your network or domain system administrator.

5 Click OK.

Windows Firewall Settings Dialog window closes.

6 On desktop, click on CT icon to start CT application.

7  As application starts, several Windows Security Alert dialog boxes appear. Click

Unblock on each dialog box as it appears.

NOTE: After performing procedure steps and CT application will not run, verify that firewall

or anti-spying software is not set to block programs without confirmation. If programs are

being blocked without confirmation, change this setting to allow confirmation, and re-start

the Craft application to determine if additional exceptions are necessary.

NOTE: Some firewall or intrusion prevention software will prevent reception of SNMP trap

messages from 10.x.x.x IP addresses, which are the default addresses for the 9500 MPR. If

operations such as provisioning equipment, creating/deleting cross-connects, etc. are

failing with either a system error or the Craft application becoming unresponsive, you may

need to allow an exception for 10.x.x.x addresses or change the IP address of the 9500 MPRunits involved.

NOTE: If an external firewall is being used, exceptions will need to be added for TCP port 21

(FTP) and udp port 5010 (SNMP).

Verify JAVA JRE Software Version

NOTE: The user's PC must have at least the Java 6 update 3 software installed.

8 Method to verify JAVA JRE software version?

If Control Panel, go to step 9.If DOS Prompt, go to step 15.

9 Click Start.

10 Click Control Panel and double click the Java icon.

11 Select About.

Page 302: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 302/314

3EM23954ABIssue 01, February 2010

Load System and Craft Terminal Software on PC4-250

DLP-132

12  Verify Java JRE software installed on the PC is at least Version 6 Update 3.

13 Click Close.

14 Go to step 21.

15 Click Start.

16 Select Run from the pop-up window.

17 Type cmd.

18  At the DOS prompt, type java -version.

19  Verify Java JRE software installed on the PC is at least Version 6 Update 3.

20 Click the X to close the DOS prompt window.

Install/Upgrade JAVA JRE Software

NOTE: The user's PC must have at least the Java 6 update 3 software installed.

21 Install/upgrade JAVA JRE on to the PC?

If yes, go to step 22.

If no, go to step 32.

22 Insert the WebEML (JUSM/CT) CD into the CD-ROM drive.

The CD will auto-run (if auto-run is enabled on the user's PC) and open up the

installation wizard.

NOTE: If auto-run does not start, user must run (double-click with left mouse button) the

Setup.exe file, available in the WebEML (JUSM/CT) CD-ROM root directory, in order to

launch the WebEML (JUSM/CT) installation wizard.

23 Installation wizard welcome screen will display after the auto-run or running the CD

manually. Click Next to continue.

24 Click Next to choose the components to install.

25 Select the Java Runtime Environment option. Click Install.

Page 303: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 303/314

3EM23954ABIssue 01, February 2010

Load System and Craft Terminal Software on PC 4-251

DLP-132

26 Click Yes to install the JRE 6 update 3 or No to cancel the Java installation.

NOTE: If the user's PC has JRE 6 update 3 or a newer Java version installed, clicking Yes

will install the JRE 6 update 3 over the existing JRE 6 update 3 but the newer version will not

be deleted. The PC will still run the most current Java version regardless if the JRE 6 update

3 is installed.

27 If the user's PC needs this Java version, click Yes to the WARNING screen above and

the JRE installation will begin.

28 Click Accept.

29 Click Finish.

30 If the user's PC has this Java version installed, this caution will appear. Click No.

31 Click Finish to complete the JRE installation.

Install WebEML (JUSM/CT) Software

32 Install WebEML (JUSM/CT) on to the PC?

If yes, go to step 33.

If no, go to step 38.

33 Insert the WebEML (JUSM/CT) CD into the CD-ROM drive.

The CD will auto-run (if auto-run is enabled on the user's PC) and open up the

installation wizard.

NOTE: If auto-run does not start, user must run (double-click with left mouse button) the

Setup.exe file, available in the WebEML (JUSM/CT) CD-ROM root directory, in order to

launch the WebEML (JUSM/CT) installation wizard.

34 Installation wizard welcome screen will display after the auto-run or running the CD

manually. Click Next to continue.

35 Click Next to choose the components to install.

36 Select the WebEML (JUSM/CT) option. Click Install.

WebEML (JUSM/CT) is installed on the PC.

Page 304: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 304/314

3EM23954ABIssue 01, February 2010

Load System and Craft Terminal Software on PC4-252

DLP-132

37 Click Finish to complete the WebEML (JUSM/CT) installation and exit the installation

wizard.

The MPR-A (WebEML) icon will be created automatically on the desktop after the

installation process.

38 STOP. This procedure is complete.

Page 305: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 305/314

3EM23954ABIssue 01, February 2010

WebEML Craft Terminal Reference Guide 5-1

WebEML Craft Terminal Reference Guide

1. INTRODUCTION

1.1 The WebEML craft terminal reference guide provides user guide to the

WebEML craft terminal. Defines the various page layouts, navigation, and

resources available to quickly monitor the condition of a 9500 MPR radio.

Main Screen Overview

1.2 The main screen view is the entry point of the application and provides

the basic diagnostic and configuration functions. This first screen shows a highlevel overview of the areas on the main screen. See Figure 1-1.

Figure 1-1. WebEML Main Screen

Page 306: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 306/314

3EM23954ABIssue 01, February 2010

WebEML Craft Terminal Reference Guide5-2

1.3 The main screen is comprised of the following areas.

• Main Menu Bar Area

Main Tool Bar Area

• Resource Tree Area

• Resource List Area

• Resource Detail Area

• Severity Alarm Synthesis Area

• Domain Alarm Synthesis Area

• Status Control Area

Main Menu Bar Area

1.4 The main menu bar area allows the management of the 9500 MPR NE

resources function to access all the menu options, performing all the

configuration and supervision functions of the Network Element. See

Figure 1-2.

1.5 The main menu bar has the following drop-down menus:

•  Views

• Configuration

• Diagnosis

Supervision

• SW Download

• Equipment

Figure 1-2. Main Menu Bar 

Page 307: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 307/314

3EM23954ABIssue 01, February 2010

WebEML Craft Terminal Reference Guide 5-3

Main Tool Bar Area

1.6 This main tool Bar area contains a selection of quick-access icons to access

common features. See Figure 1-3.

1.7 The main Tool Bar Area has the following quick-access icons:

• Backward

• Forward

• Zoom

• Block Diagram View

• Configuration View

• Cross-Connections

Resource Tree Area

1.8 Resource Tree Area displays all the available resources of the Radio

NE in a tree structure. See Figure 1-4.

Figure 1-3. Main Tool Bar Area

Page 308: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 308/314

3EM23954ABIssue 01, February 2010

WebEML Craft Terminal Reference Guide5-4

1.9 Each tree node consists of two symbols. The first symbol indicates the

state of the structure, e.g., if the symbol has a "+" the tree can be expanded to

a lower level. The tree structure can be collapsed if the symbol is a "-". Finally,

if there is no symbol, the node represents a leaf. The second symbol is the

graphical representation of the resource.

1.10 The user must select the resource by clicking with the mouse to carryout an action that depends on the type of click and the Resource Detail Area

related to the selected element that is displayed. Each resource listed may be

selected by using the mouse with a single mouse click or a double mouse click.

Figure 1-4. Resource Tree Area

Page 309: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 309/314

3EM23954ABIssue 01, February 2010

WebEML Craft Terminal Reference Guide 5-5

1.11 Single Left Click: By a single left mouse click the resource is

highlighted. This selection causes the activation of the resource list area, e.g.,

every time the user selects a resource in the resource tree area the

corresponding Tabular or Graphical representation is displayed in the

Resource List Area.

1.12 Double Left Click: Using this type of selection on the items of the resource

tree, the user can expand the tree structure and activate the Resource List Area

displaying the same information described above. When the tree node is expanded,

a double click will collapse the tree node showing the same information in the

Resource List Area.

Resource List Area

1.13 The resource list area provides a graphical view of the NE. Additional

resource function to access additional menu for performing configuration andsupervision functions of the Network Element. See Figure 1-5.

Resource Detail Area

1.14 The Resource Detail area allows the management of the 9500 MPR NEresources function to access alarm details, configuration settings, and remote

inventory details for the Network Element. See Figure 1-6.

Figure 1-5. Resource List Area

Page 310: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 310/314

3EM23954ABIssue 01, February 2010

WebEML Craft Terminal Reference Guide5-6

Severity Alarm Synthesis Area

1.15 The Severity Alarm Synthesis Area provides an alarm functionality

that informs the operator on the severity of the different alarms in the NE as

well as on the number of current alarms. See Figure 1-7.

1.16 There are six different alarm severity levels. These different levels are

associated with colors as follows:

• Green: Normal condition

• Red: Critical alarm (CRI)

• Orange: Major alarm (MAJ)

 Yellow: Minor alarm (MIN)

• Cyan: Warning alarm (WNG)

• White: Indeterminate (IND) Not operative.

Figure 1-6. Resource Detail Area

Figure 1-7. Severity Alarm Synthesis Area

Page 311: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 311/314

3EM23954ABIssue 01, February 2010

WebEML Craft Terminal Reference Guide 5-7

1.17 Each alarm severity is represented by an alarm icon situated in the

top left hand corner of the view. These alarm icons are constantly represented

on the different Equipment views (NE view, Module view or Port view) so that

the operator is always aware of the alarms occurring in the system.

1.18 The shape of the alarm icons in the alarm panel gives an indication of

alarm occurrence.

1.19  An alarm icon with a rectangle inside indicates that no alarms of the

type defined by the icon are occurring. See Figure 1-7.

1.20  An alarm icon with a circle inside it (and a number at the bottom of the

icon) indicates that alarms of the number and the type defined by the icon are

occurring. See Figure 1-8.

1.21  An alarm icon grayed out indicates that a spontaneous incoming

alarm notification has been inhibited.

Domain Alarm Synthesis Area

1.22 The Domain Alarm Synthesis Area provides an alarm functionality

that informs the operator on the domain of the different alarms in the NE as

well as on the number of current alarms. There are different alarm domain

types according to the different domains in which the NE can be subdivided

(example: External (EXT), Equipment (EQP), Transmission (TRS)). See

Figure 1-9.

Figure 1-8. Severity Alarm Synthesis Area: Alarm Condition

Figure 1-9. Domain Alarm Synthesis Area

Page 312: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 312/314

3EM23954ABIssue 01, February 2010

WebEML Craft Terminal Reference Guide5-8

1.23 The color corresponds to the highest severity among the set of active

alarms for the relevant domain. There are six different alarm severity levels.

These different levels are associated with colors as follows:

Green: Normal condition

• Red: Critical alarm (CRI)

• Orange: Major alarm (MAJ)

•  Yellow: Minor alarm (MIN)

• Cyan: Warning alarm (WNG)

• White: Indeterminate (IND) Not operative.

1.24 Each domain alarm is represented by an alarm icon situated in the top

right hand corner of the view. These alarm icons are constantly represented on

the different domain types so that the operator is always aware of the alarms

occurring in the system.

1.25 The shape of the alarm icons in the alarm panel gives an indication of

alarm occurrence. An alarm icon with a rectangle inside indicates that no

alarms of the type defined by the icon are occurring. See Figure 1-10.

1.26  An alarm icon with a circle inside it (and a number at the bottom of the

icon) indicates that alarms of the number and the type defined by the icon are

occurring. See Figure 1-10.

1.27  An alarm icon grayed out indicates that a spontaneous incoming

alarm notification has been inhibited.

Status Control Area

1.28 The Status Control Area provides different management states

concerning the NE and are represented via icons located on the right side of the

Resource List Area. See Figure 1-11.

Figure 1-10. Domain Alarm Synthesis Area: Alarm Condition

Page 313: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 313/314

3EM23954ABIssue 01, February 2010

WebEML Craft Terminal Reference Guide 5-9

1.29 Refer to Table 1-A  for the seven management status icon and color

definitions.

Figure 1-11. Status Control Area

Page 314: 9500 MPR O _26 M

8/9/2019 9500 MPR O _26 M

http://slidepdf.com/reader/full/9500-mpr-o-26-m 314/314