ADIMLab 3D Printer

user's manual

version V 1.2

Contents 1. Equipment Architecture ............................................................................................ 错误！未定义书签。

2. Equipment Architecture .............................................................................................................................. 4

3. installation .................................................................................................................................................. 10

4. Wiring and consumable loading ............................................................................... 错误！未定义书签。

5. Leveling ...................................................................................................................................................... 16

6.Print test ...................................................................................................................................................... 17

7.Filament ...................................................................................................................................................... 18

8. Motherboard wiring diagram ................................................................................................................... 20

Notice Thank you very much for your purchase and support of our 3D printer. You may have purchased some of our other 3D products or have an

understanding of 3D printing technology. But we still hope that you can read the product guide carefully, and it contains a lot of important

information about the use of the product to give customers a better 3D experience. After reading and understanding the operation, you can start

your first print right away.

Before using this unit, be sure to read the following:

1. Safety Precautions please use the consumables recommended by the original manufacturer for printer consumables. Do not use other

manufacturers' consumables at will, so as to avoid nozzle blockage. Do not attempt to use the unit in any way that is not described in the

instructions for use to avoid accidental personal injury and property damage.

2. This machine is suitable for being placed in a ventilated, dry and dust-free environment. Pay attention to the heat dissipation around the printer

when using it, and avoid placing it on a thick carpet or against a wall. Do not place the unit near flammable or explosive materials or high heat

sources. Do not place the unit in a location subject to excessive vibration or other instability. Do not stack heavy objects on the unit.

3. Use the power cord supplied with the unit in accordance with the specifications. Do not plug or unplug the power cord when your hands are

wet. Use a qualified three-hole socket with a ground wire. Do not deliberately pull or excessively twist the distribution line of the unit to prevent

open circuit or short circuit. Ensure grounding before running the printer to protect the printer from static electricity.

4. During the printing process, please note that the machine is equipped with an integrated hot bed heating plate. When using the hot bed

function, do not set the hot bed temperature to more than 60 degrees Celsius to avoid burns. If you are under the age of 10, do not use the unit

without personal supervision to avoid personal injury. Avoid touching the printer nozzle structure during printing and when printing is complete

to prevent burns. If abnormal noise occurs during printing, immediately turn off the power switch, stop the printer, and contact your purchaser. It

is often used for product maintenance, and the machine is regularly dusted and lubricated. Do not attempt to disassemble or modify the unit

using methods not described in this manual to prevent damage to the printer or other more serious safety incidents. Regularly clean the printer

with a dry cloth in the event of a power outage, and wipe off dust and bonded printed materials. If it must be cleaned with a damp cloth, do not

use flammable solvents to prevent flammable solvents from coming into contact with the printer's internal circuits for fire or electric shock

5. Power off in time after printing. After the printing is finished, use the remaining temperature of the nozzle in time to clean the consumables on

the nozzle with tools. Do not touch the nozzle directly with your hand. Try not to scratch the hot bed when you use the blade to take the model.

Do a good job of maintenance in the later stage, timely deducting and lubrication, when the printer is not used for a long time, please power off

the machine and dust the machine.

6. Please place the printer on a flat and solid platform. Before the first printing, please adjust the nozzle of the machine parallel to the printing

platform to prevent the nozzle from smashing the platform.

1.Equipment architecture

1. Rack 2. Extruder 3. Z-axis right slider 4. Nozzle 5. Print platform 6. LCD display 7. Platform leveling knob 8. Foot pad 9. Broken material detection module 10. X-axis limit Bit switch 11. Z-axis left slider 12. Z-axis limit switch 13. Cooling fan 14. Main board control box 15. Z-axis screw 16. Power supply 17. Z-axis copper screw 18. X-axis motor 19. Coupling 20. Z-axis motor 21. Y-axis motor

2. Equipment component The whole machine is basically assembled into multiple modules before leaving the factory. We need to assemble these modules into the whole

machine we need.

number photo model quantity

1

Print platform component 1

2

Z-axis slider left component

1

3

Z-axis slider right component 1

4

Extruder 1

5

Main board 1

6

LCD display 1

7

Power supply 1

8

X driven wheel bracket

assembly

1

9

Z axis Limit switch 1

10

Filament holder 1

11

rod 1

12

Z axis motor 1

13

Z axis Screw fixing plate 1

14

Z axis fixing plate 1

15

Bottom vertical bracket,

model 2040, length 330mm,

serial number ○1 、

2

○2

16

Bottom lateral bracket, model

2020, length 333mm, serial

number ○3 、

2

○4

17

Longmen vertical bracket left,

model 2040, length 390mm,

serial number ○5

1

18

Longmen vertical bracket

right, model 2040, length

390mm, serial number ○6

1

19

Gantry horizontal bracket,

model 2020, length 333mm,

serial number ○7

1

20

X-axis guide bracket, model

2020, length 343mm, serial

number ○8

1

3.Printer installation

Step 1: Install the base frame

As shown in the figure: Install the No. 1-4 profile with a M5X30 screw into a square frame, then lock the foot pad with the M6 nut under the

four corners of the profile, and then use the four M4X25 screws for the print platform assembly (component No. 1). Installed to the square

frame.

Step 2: Install the X-axis assembly

As shown in the figure: Install the extrusion head assembly into the No. 8 profile, then install the left and right X-axis components with two

M4X25 screws on both sides, and then install the belt and clamp it.

Step 3: Install the Z-axis assembly

Figure: First step to install profiles No. 5 and No. 6; second step to install No. 12 Z-axis motor components; third step to install X-axis

components; fourth step to install No. 11 screw; fifth step to install No. 13 Z-axis Screw rod fixing plate assembly; the sixth step is to install the

No. 9 Z-axis limit switch mounting plate assembly and the No. 14 Z-axis fixing plate assembly, and then install the profile cover.

Step 4: Install the power supply components, motherboard components, and display components

As shown in the figure: Install the power supply component on the 7th, then loosen the right front screw and install the 6th display component,

and then install the 5th motherboard component. (Note: After the motherboard component is placed close to the front display component, it will

prevent the Z-axis from hitting the motherboard when it returns to zero.)

4. Equipment wiring and consumable filling

1. Connect the machine harness as shown below.

2. Insert the consumable into the extruder and insert it into the extruder (as shown)

5. Leveling 1. Prepare → Align the hot bed and wait for the nozzle to return to the original position to move to the left front of the platform.

2. Click Start and the nozzle will move to the four points above the platform.

3. Rotate the four platform screws under the platform to adjust the nozzle of the printing platform so that the nozzle spacing from the platform is slightly larger than the thickness of one A4 paper, and the spacing is about 0.2mm. We can use an A4 paper to assist in leveling so that the nozzle can easily pass through an A4 sheet.

4. Complete the 4 points leveling in turn, the first leveling can be repeated once, and the leveling accuracy will be better.

6.Print test 1. Select the model from the menu, click Print, the standby device preheats the hot bed, and then preheats the extruder. After a few minutes, the

machine will start printing

2. Observe the printing situation, whether the first layer is printed smoothly

7.Put filament 1.Preheat PLA in Prepare

2. Wait for the nozzle temperature to heat up to the predetermined temperature, and select the refueling in preparation

3. Return and feed

4. After refueling, the nozzle can extrude the wire and choose to resume printing.

8. Motherboard wiring diagram

Contact Email：adimlab@gmail.com Facebook group: ADIMLab 3D Printer Skype: ADIMLab 3D Printer