70
TLC225x, TLC225xA Advanced LinCMOS RAIL-TO-RAIL VERY LOW-POWER OPERATIONAL AMPLIFIERS SLOS176D – FEBRUARY 1997 – REVISED MARCH 2001 1 POST OFFICE BOX 655303 DALLAS, TEXAS 75265 Output Swing Includes Both Supply Rails Low Noise . . . 19 nV/Hz Typ at f = 1 kHz Low Input Bias Current . . . 1 pA Typ Fully Specified for Both Single-Supply and Split-Supply Operation Very Low Power . . . 35 µA Per Channel Typ Common-Mode Input Voltage Range Includes Negative Rail Low Input Offset Voltage 850 µV Max at T A = 25°C (TLC225xA) Macromodel Included Performance Upgrades for the TS27L2/L4 and TLC27L2/L4 Available in Q–Temp Automotive HighRel Automotive Applications Configuration Control / Print Support Qualification to Automotive Standards description The TLC2252 and TLC2254 are dual and quadruple operational amplifiers from Texas Instruments. Both devices exhibit rail-to-rail output performance for increased dynamic range in single- or split-supply applications. The TLC225x family consumes only 35 µA of supply current per channel. This micropower operation makes them good choices for battery-powered applications. The noise performance has been dramatically improved over previous generations of CMOS amplifiers. Looking at Figure 1, the TLC225x has a noise level of 19 nV/Hz at 1kHz; four times lower than competitive micropower solutions. The TLC225x amplifiers, exhibiting high input impedance and low noise, are excellent for small-signal conditioning for high-impedance sources, such as piezoelectric transducers. Because of the micropower dissipation levels, these devices work well in hand-held monitoring and remote-sensing applications. In addition, the rail-to-rail output feature with single or split supplies makes this family a great choice when interfacing with analog-to-digital converters (ADCs). For precision applications, the TLC225xA family is available and has a maximum input offset voltage of 850 µV. This family is fully characterized at 5 V and ± 5 V. The TLC2252/4 also makes great upgrades to the TLC27L2/L4 or TS27L2/L4 in standard designs. They offer increased output dynamic range, lower noise voltage, and lower input offset voltage. This enhanced feature set allows them to be used in a wider range of applications. For applications that require higher output drive and wider input voltage ranges, see the TLV2432 and TLV2442 devices. If the design requires single amplifiers, please see the TLV2211/21/31 family. These devices are single rail-to-rail operational amplifiers in the SOT-23 package. Their small size and low power consumption, make them ideal for high density, battery-powered equipment. Copyright 2001, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Advanced LinCMOS is a trademark of Texas Instruments. Figure 1 VN – Equivalent Input Noise Voltage – nv//Hz f – Frequency – Hz EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY nV/ Hz V n 40 20 10 0 60 30 50 10 1 10 2 10 3 10 4 V DD = 5 V R S = 20 T A = 25°C On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters.

Advanced LinCMOS Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

Embed Size (px)

Citation preview

Page 1: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

1POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

Output Swing Includes Both Supply Rails

Low Noise . . . 19 nV/√Hz Typ at f = 1 kHz

Low Input Bias Current . . . 1 pA Typ

Fully Specified for Both Single-Supply andSplit-Supply Operation

Very Low Power . . . 35 µA Per Channel Typ

Common-Mode Input Voltage RangeIncludes Negative Rail

Low Input Offset Voltage 850 µV Max at TA = 25°C (TLC225xA)

Macromodel Included

Performance Upgrades for the TS27L2/L4and TLC27L2/L4

Available in Q–Temp Automotive HighRel Automotive ApplicationsConfiguration Control / Print SupportQualification to Automotive Standards

description

The TLC2252 and TLC2254 are dual andquadruple operational amplifiers from TexasInstruments. Both devices exhibit rail-to-railoutput performance for increased dynamic rangein single- or split-supply applications. TheTLC225x family consumes only 35 µA of supplycurrent per channel. This micropower operationmakes them good choices for battery-poweredapplications. The noise performance has beendramatically improved over previous generationsof CMOS amplifiers. Looking at Figure 1, theTLC225x has a noise level of 19 nV/√Hz at 1kHz;four times lower than competitive micropowersolutions.

The TLC225x amplifiers, exhibiting high inputimpedance and low noise, are excellent forsmall-signal conditioning for high-impedancesources, such as piezoelectric transducers.Because of the micropower dissipation levels,these devices work well in hand-held monitoringand remote-sensing applications. In addition, therail-to-rail output feature with single or splitsupplies makes this family a great choice when interfacing with analog-to-digital converters (ADCs). Forprecision applications, the TLC225xA family is available and has a maximum input offset voltage of 850 µV. Thisfamily is fully characterized at 5 V and ±5 V.

The TLC2252/4 also makes great upgrades to the TLC27L2/L4 or TS27L2/L4 in standard designs. They offerincreased output dynamic range, lower noise voltage, and lower input offset voltage. This enhanced feature setallows them to be used in a wider range of applications. For applications that require higher output drive andwider input voltage ranges, see the TLV2432 and TLV2442 devices. If the design requires single amplifiers,please see the TLV2211/21/31 family. These devices are single rail-to-rail operational amplifiers in the SOT-23package. Their small size and low power consumption, make them ideal for high density, battery-poweredequipment.

Copyright 2001, Texas Instruments IncorporatedPRODUCTION DATA information is current as of publication date.Products conform to specifications per the terms of Texas Instrumentsstandard warranty. Production processing does not necessarily includetesting of all parameters.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications ofTexas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

Advanced LinCMOS is a trademark of Texas Instruments.

Figure 1

VN

– E

qu

ival

ent

Inp

ut

No

ise

Vo

ltag

e –

nv/

/Hz

f – Frequency – Hz

EQUIVALENT INPUT NOISE VOLTAGEvs

FREQUENCY

nV

/H

zV

n

40

20

10

0

60

30

50

101 102 103 104

VDD = 5 VRS = 20 ΩTA = 25°C

On products compliant to MIL-PRF-38535, all parameters are testedunless otherwise noted. On all other products, productionprocessing does not necessarily include testing of all parameters.

Page 2: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TLC2252 AVAILABLE OPTIONS

PACKAGED DEVICES

TAVIOmaxAT 25°C

SMALLOUTLINE†

(D)

CHIPCARRIER

(FK)

CERAMICDIP(JG)

PLASTICDIP(P)

TSSOP‡

(PW)

CERAMICFLATPACK

(U)

0°C to 70°C 1500 µV TLC2252CD — — TLC2252CP TLC2252CPW —

40°C to 125°C850 µV TLC2252AID — — TLC2252AIP TLC2252AIPW —

–40°C to 125°Cµ

1500 µV TLC2252ID — — TLC2252IP — —

40°C to 125°C850 µV TLC2252AQD — — — — —

–40°C to 125°Cµ

1500 µV TLC2252QD — — — — —

–55°C to 125°C850 µV

1500 µV——

TLC2252AMFKTLC2252MFK

TLC2252AMJGTLC2252MJG

——

——

TLC2252AMUTLC2252MU

† The D packages are available taped and reeled. Add R suffix to device type (e.g., TLC2262CDR).‡ The PW package is available only left-ended taped and reeled.§ Chip forms are tested at 25°C only.

TLC2254 AVAILABLE OPTIONS

PACKAGED DEVICES

TAVIOmaxAT 25°C

SMALL OUTLINE†

(D)

CHIP CARRIER

(FK)

CERAMIC DIP(J)

PLASTIC DIP(N)

TSSOP‡

(PW)

CERAMICFLATPACK

(W)

0°C to70°C 1500 µV TLC2254CD — — TLC2254CN TLC2254CPW —

–40°C to 850 µV TLC2254AID — — TLC2254AIN TLC2254AIPW —

125°Cµ

1500 µV TLC2254ID — — TLC2254IN — —

–40°C to 850 µV TLC2254AQD — — — — —125°C

µ1500 µV TLC2254QD — — — — —

–55°C to 850 µV — TLC2254AMFK TLC2254AMJ — — TLC2254AMW125°C

µ1500 µV — TLC2254MFK TLC2254MJ — — TLC2254MW

† The D packages are available taped and reeled. Add R suffix to the device type (e.g., TLC2254CDR).‡ The PW package is available only left-end taped and reeled. Chips are tested at 25°C.§ Chip forms are tested at 25°C only.

Page 3: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

3POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TLC2252M, TLC2252AM . . . JG PACKAGE(TOP VIEW)

TLC2252C, TLC2252ACTLC2252I, TLC2252AI

TLC2252Q, TLC2252AQD, P, OR PW PACKAGE

(TOP VIEW)

1

2

3

4

8

7

6

5

1OUT1IN–1IN+

VDD– /GND

VDD+2OUT2IN–2IN+

NCVCC +2OUT2IN –2IN +

NC1OUT1IN –1IN +

VCC– /GND

1

2

3

4

5

10

9

8

7

6

TLC2262M, TLC2252AM . . . U PACKAGE(TOP VIEW)

1

2

3

4

8

7

6

5

1OUT1IN–1IN+

VDD– /GND

VDD+2OUT2IN–2IN+

3 2 1 20 19

9 10 11 12 13

4

5

6

7

8

18

17

16

15

14

NC2OUTNC2IN–NC

NC1IN–

NC1IN+

NC

NC

1OU

TN

C2I

N+

NC

NC

NC

NC

VD

D+

VD

D–

TLC2252M, TLC2252AM . . . FK PACKAGE(TOP VIEW)

/GN

D

1

2

3

4

5

6

7

14

13

12

11

10

9

8

1OUT1IN–1IN+

VDD+2IN+2IN–

2OUT

4OUT4IN–4IN+VDD– /GND3IN+3IN–3OUT

3 2 1 20 19

9 10 11 12 13

4

5

6

7

8

18

17

16

15

14

4IN+NCVCC– /GNDNC3IN+

1IN+NC

VCC+NC

2IN+

1IN

–1O

UT

NC

3OU

T3I

N –

4OU

T4I

N –

2IN

–2O

UT

NC

TLC2254M, TLC2254AMFK PACKAGE(TOP VIEW)

TLC2254C, TLC2254ACTLC2254I, TLC2254AI

TLC2254Q, TLC2254AQD, N, OR PW PACKAGE

(TOP VIEW)

1

2

3

4

5

6

7

14

13

12

11

10

9

8

1OUT1IN–1IN+

VDD+2IN+2IN–

2OUT

4OUT4IN–4IN+VDD– /GND3IN+3IN–3OUT

TLC2254M, TLC2254AMJ OR W PACKAGE

(TOP VIEW)

NC – No internal connection

Page 4: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

equivalent schematic (each amplifier)

Q3 Q6 Q9 Q12 Q14 Q16

Q2 Q5 Q7 Q8 Q10 Q11

D1

Q17Q15Q13

Q4Q1

R5

C1

VDD+

IN+

IN–

R3 R4 R1 R2

OUT

VDD– /GND

R6

ACTUAL DEVICE COMPONENT COUNT†

COMPONENT TLC2252 TLC2254

Transistors 38 76

Resistors 30 56

Diodes 9 18

Capacitors 3 6† Includes both amplifiers and all ESD, bias, and trim circuitry

Page 5: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

5POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†

Supply voltage, VDD+ (see Note 1) 8 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supply voltage, VDD– (see Note 1) –8 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Differential input voltage, VID (see Note 2) ±16 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input voltage, VI (any input, see Note 1) ±8 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input current, II (each input) ±5 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Output current, IO ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Total current into VDD+ ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Total current out of VDD– ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Duration of short-circuit current at (or below) 25°C (see Note 3) unlimited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous total dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating free-air temperature range, TA: C suffix 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

I suffix –40°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Q suffix –40°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M suffix –55°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Storage temperature range, Tstg –65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, andfunctional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is notimplied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VDD+ and VDD – .2. Differential voltages are at IN+ with respect to IN–. Excessive current flows when input is brought below VDD– – 0.3 V.3. The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum

dissipation rating is not exceeded.

DISSIPATION RATING TABLE

PACKAGETA ≤ 25°C DERATING FACTOR TA = 70°C TA = 85°C TA = 125°C

PACKAGE APOWER RATING ABOVE TA = 25°C

APOWER RATING

APOWER RATING

APOWER RATING

D–8 724 mW 5.8 mW/°C 464 mW 377 mW 144 mW

D–14 950 mW 7.6 mW/°C 608 mW 450 mW 190 mW

FK 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW

J 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW

JG 1050 mW 8.4 mW/°C 672 mW 546 mW 275 mW

N 1150 mW 9.2 mW/°C 736 mW 736 mW —

P 1000 mW 8.0 mW/°C 640 mW 520 mW —

PW–8 525 mW 4.2 mW/°C 336 mW 273 mW —

PW–14 700 mW 5.6 mW/°C 448 mW 448 mW —

U 700 mW 5.5 mW/°C 246 mW 330 mW 150 mW

W 700 mW 5.5 mW/°C 246 mW 330 mW 150 mW

recommended operating conditions

C SUFFIX I SUFFIX Q SUFFIX M SUFFIXUNIT

MIN MAX MIN MAX MIN MAX MIN MAXUNIT

Supply voltage, VDD± ±2.2 ±8 ±2.2 ±8 ±2.2 ±8 ±2.2 ±8 V

Input voltage range, VI VDD– VDD+ –1.5 VDD– VDD+ –1.5 VDD– VDD+ –1.5 VDD– VDD+ –1.5 V

Common-mode input voltage, VIC VDD– VDD+ –1.5 VDD– VDD+ –1.5 VDD– VDD+ –1.5 VDD– VDD+ –1.5 V

Operating free-air temperature, TA 0 70 –40 125 –40 125 –55 125 °C

Page 6: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS T †TLC2252C

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX

UNIT

VIO Input offset voltage25°C 200 1500

µVVIO Input offset voltageFull range 1750

µV

αVIO Temperature coefficient of input offset voltage25°C

0 5 µV/°CαVIO Temperature coefficient of input offset voltageto 70°C 0.5 µV/°C

Input offset voltage long-term drift (see Note 4) VIC = 0,VO = 0

VDD± = ±2.5 V,RS = 50 Ω

25°C 0.003 µV/mo

IIO Input offset current

VO = 0, RS = 50 Ω25°C 0.5 60

pAIIO Input offset currentFull range 100

pA

IIB Input bias current25°C 1 60

pAIIB Input bias currentFull range 100

pA

0 –0.325°C

0to

0.3to

VICR Common mode input voltage range RS = 50 Ω |VIO | ≤ 5 mV4 4.2

VVICR Common-mode input voltage range RS = 50 Ω, |VIO | ≤ 5 mV0

V

Full range0tog

3.5

IOH = –20 µA 25°C 4.98

VOH High level output voltage IOH = 75 µA25°C 4.9 4.94

VVOH High-level output voltage IOH = –75 µAFull range 4.8

V

IOH = –150 µA 25°C 4.8 4.88

VIC = 2.5 V, IOL = 50 µA 25°C 0.01

VIC = 2 5 V IOL = 500 µA25°C 0.09 0.15

VIC = 2.5 V, IOL = 500 µAFull range 0.15

VOL Low-level output voltageVIC = 2 5 V IOL = 1 A

25°C 0.2 0.3 VVIC = 2.5 V, IOL = 1 A

Full range 0.3

VIC = 2 5 V IOL = 4 A25°C 0.7 1

VIC = 2.5 V, IOL = 4 AFull range 1.2

V 2 5 V R 100 kΩ‡25°C 100 350

AVD Large-signal differential voltage amplificationVIC = 2.5 V,VO = 1 V to 4 V

RL = 100 kهFull range 10 V/mVVD g g g VO = 1 V to 4 V

RL = 1 MΩ‡ 25°C 1700

rid Differential input resistance 25°C 1012 Ω

ric Common-mode input resistance 25°C 1012 Ω

cic Common-mode input capacitance f = 10 kHz, P package 25°C 8 pF

zo Closed-loop output impedance f = 25 kHz, AV = 10 25°C 200 Ω

CMRR Common mode rejection ratioVIC = 0 to 2.7 V, VO = 2.5 V, 25°C 70 83

dBCMRR Common-mode rejection ratio IC , O ,RS = 50 Ω Full range 70

dB

kSVR Supply voltage rejection ratio (∆VDD/∆VIO)VDD = 4.4 V to 16 V, 25°C 80 95

dBkSVR Supply-voltage rejection ratio (∆VDD/∆VIO) DD ,VIC = VDD/2, No load Full range 80

dB

IDD Supply current VO = 2 5 V No load25°C 70 125

µAIDD Supply current VO = 2.5 V, No loadFull range 150

µA

† Full range is 0°C to 70°C.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated

to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

Page 7: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

7POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

operating characteristics at specified free-air temperature, VDD = 5 V

PARAMETER TEST CONDITIONS T †TLC2252C

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX

UNIT

VO 1 5 V to 3 5 V RL 100 kΩ‡25°C 0.07 0.12

SR Slew rate at unity gain VO = 1.5 V to 3.5 V, RL = 100 kΩ‡,CL = 100 pF‡ Full

0 05V/µs

CL = 100 F‡range

0.05

V Equivalent input noise voltagef = 10 Hz 25°C 36

nV/√HzVn Equivalent input noise voltagef = 1 kHz 25°C 19

nV/√Hz

VN(PP) Peak to peak equivalent input noise voltagef = 0.1 Hz to 1 Hz 25°C 0.7

µVVN(PP) Peak-to-peak equivalent input noise voltagef = 0.1 Hz to 10 Hz 25°C 1.1

µV

In Equivalent input noise current 25°C 0.6 fA√Hz

THD + N Total harmonic distortion plus noiseVO = 0.5 V to 2.5 V,f 10 kHz

AV = 125°C

0.2%THD + N Total harmonic distortion plus noise f = 10 kHz,

RL = 50 kΩ‡ AV = 1025°C

1%

Gain-bandwidth productf = 10 kHz, CL = 100 pF‡

RL = 50 kΩ‡, 25°C 0.2 MHz

BOM Maximum output-swing bandwidthVO(PP) = 2 V, RL = 50 kه,

AV = 1, CL = 100 pF‡ 25°C 30 kHz

φm Phase margin at unity gainRL = 50 kΩ‡ CL = 100 pF‡ 25°C 63°

Gain marginRL = 50 kΩ‡, CL = 100 pF‡

25°C 15 dB† Full range is 0°C to 70°C.‡ Referenced to 2.5 V

Page 8: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwisespecified)

PARAMETER TEST CONDITIONS T †TLC2252C

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX

UNIT

VIO Input offset voltage

V

25°C 200 1500µVVIO Input offset voltage

V

Full range 1750µV

αVIO Temperature coefficient of input offset voltage

V

25°C0 5 µV/°CαVIO Temperature coefficient of input offset voltage

Vto 70°C 0.5 µV/°C

Input offset voltage long-term drift (see Note 4) VIC = 0,RS = 50 Ω

VO = 0, 25°C 0.003 µV/mo

IIO Input offset current

RS = 50 Ω25°C 0.5 60

pAIIO Input offset currentFull range 100

pA

IIB Input bias current25°C 1 60

pAIIB Input bias currentFull range 100

pA

–5 –5.325°C

5to

5.3to

VICR Common mode input voltage range |VIO | ≤5 mV RS = 50 Ω4 4.2

VVICR Common-mode input voltage range |VIO | ≤5 mV, RS = 50 Ω–5

V

Full range5tog

3.5

IO = –20 µA 25°C 4.98

VOM Maximum positive peak output voltage IO = 100 µA25°C 4.9 4.93

VVOM+ Maximum positive peak output voltage IO = –100 µAFull range 4.7

V

IO = –200 µA 25°C 4.8 4.86

VIC = 0, IO = 50 µA 25°C –4.99

VIC = 0 IO = 500 µA25°C –4.85 –4.91

VIC = 0, IO = 500 µAFull range –4.85

VOM– Maximum negative peak output voltageVIC = 0 IO = 1 A

25°C –4.7 –4.8 VVIC = 0, IO = 1 A

Full range –4.7

VIC = 0 IO = 4 A25°C –4 –4.3

VIC = 0, IO = 4 AFull range –3.8

RL = 100 kΩ25°C 45 650

AVD Large-signal differential voltage amplification VO = ±4 VRL = 100 kΩ

Full range 10 V/mV

RL = 1 MΩ 25°C 3000

rid Differential input resistance 25°C 1012 Ω

ric Common-mode input resistance 25°C 1012 Ω

cic Common-mode input capacitance f = 10 kHz, P package 25°C 8 pF

zo Closed-loop output impedance f = 25 kHz, AV = 10 25°C 190 Ω

CMRR Common mode rejection ratioVIC = –5 V to 2.7 V, 25°C 75 88

dBCMRR Common-mode rejection ratioVO = 0, RS = 50 Ω Full range 75

dB

kSVR Supply voltage rejection ratio (∆VDD± /∆VIO)VDD± = 2.2 V to ±8 V, 25°C 80 95

dBkSVR Supply-voltage rejection ratio (∆VDD± /∆VIO)VIC = 0, No load Full range 80

dB

IDD Supply current VO = 0 No load25°C 80 125

µAIDD Supply current VO = 0, No loadFull range 150

µA

† Full range is 0°C to 70°C.NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated

to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

Page 9: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

9POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

operating characteristics at specified free-air temperature, VDD± = ±5 V

PARAMETER TEST CONDITIONS T †TLC2252C

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX

UNIT

VO = ±1 9 V RL = 100 kΩ25°C 0.07 0.12

SR Slew rate at unity gainVO = ±1.9 V, CL = 100 pF

RL = 100 kΩ,Full

range0.05

V/µs

V Equivalent input noise voltagef = 10 Hz 25°C 38

nV/√HzVn Equivalent input noise voltagef = 1 kHz 25°C 19

nV/√Hz

VN(PP) Peak to peak equivalent input noise voltagef = 0.1 Hz to 1 Hz 25°C 0.8

µVVN(PP) Peak-to-peak equivalent input noise voltagef = 0.1 Hz to 10 Hz 25°C 1.1

µV

In Equivalent input noise current 25°C 0.6 fA√Hz

THD + N Total harmonic distortion pulse durationVO = ±2.3 V,f 10 kHz

AV = 125°C

0.2%THD + N Total harmonic distortion pulse duration f = 10 kHz,

RL = 50 kΩ AV = 1025°C

1%

Gain-bandwidth productf = 10 kHz,CL = 100 pF

RL = 50 kΩ,25°C 0.21 MHz

BOM Maximum output-swing bandwidthVO(PP) = 4.6 V,RL = 50 kΩ,

AV = 1,CL = 100 pF

25°C 14 kHz

φm Phase margin at unity gainRL = 50 kΩ CL = 100 pF

25°C 63°

Gain marginRL = 50 kΩ, CL = 100 pF

25°C 15 dB

† Full range is 0°C to 70°C.

Page 10: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS T †TLC2254C

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX

UNIT

VIO Input offset voltage25°C 200 1500

µVVIO Input offset voltageFull range 1750

µV

αVIO Temperature coefficient of input offset voltage25°C

to 70°C 0.5 µV/°C

Input offset voltage long-term drift (see Note 4) VIC = 0,VO = 0

VDD± = ±2.5 V,RS = 50 Ω

25°C 0.003 µV/mo

IIO Input offset current

VO = 0, RS = 50 Ω25°C 0.5 60

pAIIO Input offset currentFull range 100

pA

IIB Input bias current25°C 1 60

pAIIB Input bias currentFull range 100

pA

VICR Common mode input voltage range RS = 50 Ω |VIO | ≤ 5 mV

25°C0to4

–0.3to

4.2VVICR Common-mode input voltage range RS = 50 Ω, |VIO | ≤ 5 mV

Full range0to

3.5

V

IOH = –20 µA 25°C 4.98

VOH High level output voltage IOH = 75 µA25°C 4.9 4.94

VVOH High-level output voltage IOH = –75 µAFull range 4.8

V

IOH = –150 µA 25°C 4.8 4.88

VIC = 2.5 V, IOL = 50 µA 25°C 0.01

VIC = 2 5 V IOL = 500 µA25°C 0.09 0.15

VIC = 2.5 V, IOL = 500 µAFull range 0.15

VOL Low-level output voltageVIC = 2 5 V IOL = 1 A

25°C 0.2 0.3 VVIC = 2.5 V, IOL = 1 A

Full range 0.3

VIC = 2 5 V IOL = 4 A25°C 0.7 1

VIC = 2.5 V, IOL = 4 AFull range 1.2

V 2 5 V R 100 kΩ‡25°C 100 350

AVD Large-signal differential voltage amplificationVIC = 2.5 V,VO = 1 V to 4 V

RL = 100 kهFull range 10 V/mVVD g g g VO = 1 V to 4 V

RL = 1 MΩ‡ 25°C 1700

ri(d) Differential input resistance 25°C 1012 Ω

ri(c) Common-mode input resistance 25°C 1012 Ω

ci(c) Common-mode input capacitance f = 10 kHz, N package 25°C 8 pF

zo Closed-loop output impedance f = 25 kHz, AV = 10 25°C 200 Ω

CMRR Common mode rejection ratioVIC = 0 to 2.7 V, VO = 2.5 V, 25°C 70 83

dBCMRR Common-mode rejection ratio IC , O ,RS = 50 Ω Full range 70

dB

kSVR Supply voltage rejection ratio (∆VDD/∆VIO)VDD = 4.4 V to 16 V, 25°C 80 95

dBkSVR Supply-voltage rejection ratio (∆VDD/∆VIO) DD ,VIC = VDD/2, No load Full range 80

dB

IDD Supply current (four amplifiers) VO = 2 5 V No load25°C 140 250

µAIDD Supply current (four amplifiers) VO = 2.5 V, No loadFull range 300

µA

† Full range is 0°C to 70°C.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated

to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

Page 11: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

11POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

operating characteristics at specified free-air temperature, VDD = 5 V

PARAMETER TEST CONDITIONS T †TLC2254C

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX

UNIT

SR Slew rate at unity gainVO = 1.4 V to 2.6 V RL = 100 kΩ‡, 25°C 0.07 0.12

V/µsSR Slew rate at unity gain OCL = 100 pF‡

L ,

Full range 0.05V/µs

V Equivalent input noise voltagef = 10 Hz 25°C 36

nV/√HzVn Equivalent input noise voltagef = 1 kHz 25°C 19

nV/√Hz

VN(PP)Peak-to-peak equivalent input noise f = 0.1 Hz to 1 Hz 25°C 0.7

µVVN(PP)q

voltage f = 0.1 Hz to 10 Hz 25°C 1.1µV

In Equivalent input noise current 25°C 0.6 fA /√Hz

THD + N Total harmonic distortion plus noiseVO = 0.5 V to 2.5 V,f = 10 kHz

AV = 125°C

0.2%THD + N Total harmonic distortion plus noise f = 10 kHz,

RL = 50 kΩ‡ AV = 1025°C

1%

Gain-bandwidth productf = 10 kHz, CL = 100 pF‡

RL = 50 kΩ‡, 25°C 0.2 MHz

BOM Maximum output-swing bandwidthVO(PP) = 2 V, RL = 50 kه,

AV = 1, CL = 100 pF‡ 25°C 30 kHz

φm Phase margin at unity gainRL = 50 kΩ‡ CL = 100 pF‡ 25°C 63°

Gain marginRL = 50 kΩ‡, CL = 100 pF‡

25°C 15 dB† Full range is 0°C to 70°C.‡ Referenced to 2.5 V

Page 12: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwisespecified)

PARAMETER TEST CONDITIONS T †TLC2254C

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX

UNIT

VIO Input offset voltage25°C 200 1500

µVVIO Input offset voltageFull range 1750

µV

αVIO Temperature coefficient of input offset voltage25°C

to 70°C 0.5 µV/°C

Input offset voltage long-term drift (see Note 4) VIC = 0,RS = 50 Ω

VO = 0, 25°C 0.003 µV/mo

IIO Input offset current

RS = 50 Ω25°C 0.5 60

pAIIO Input offset currentFull range 100

pA

IIB Input bias current25°C 1 60

pAIIB Input bias currentFull range 100

pA

VICR Common mode input voltage range |VIO | ≤5 mV RS = 50 Ω

25°C–5to4

–5.3to

4.2VVICR Common-mode input voltage range |VIO | ≤5 mV, RS = 50 Ω

Full range–5to

3.5

V

IO = –20 µA 25°C 4.98

VOM Maximum positive peak output voltage IO = 100 µA25°C 4.9 4.93

VVOM+ Maximum positive peak output voltage IO = –100 µAFull range 4.7

V

IO = –200 µA 25°C 4.8 4.86

VIC = 0, IO = 50 µA 25°C –4.99

VIC = 0 IO = 500 µA25°C –4.85 –4.91

VIC = 0, IO = 500 µAFull range –4.85

VOM– Maximum negative peak output voltageVIC = 0 IO 1 A

25°C –4.7 –4.8 VVIC = 0, IO = 1 A

Full range –4.7

VIC = 0 IO 4 A25°C –4 –4.3

VIC = 0, IO = 4 AFull range –3.8

RL = 100 kΩ25°C 40 150

AVD Large-signal differential voltage amplification VO = ±4 VRL = 100 kΩ

Full range 10 V/mV

RL = 1 MΩ 25°C 3000

ri(d) Differential input resistance 25°C 1012 Ω

ri(c) Common-mode input resistance 25°C 1012 Ω

ci(c) Common-mode input capacitance f = 10 kHz, N package 25°C 8 pF

zo Closed-loop output impedance f = 25 kHz, AV = 10 25°C 190 Ω

CMRR Common mode rejection ratioVIC = –5 V to 2.7 V, 25°C 75 88

dBCMRR Common-mode rejection ratio IC ,VO = 0, RS = 50 Ω Full range 75

dB

kSVR Supply voltage rejection ratio (∆VDD± /∆VIO)VDD± = ±2.2 V to ±8 V, 25°C 80 95

dBkSVR Supply-voltage rejection ratio (∆VDD± /∆VIO) DD± ,VIC = 0, No load Full range 80

dB

IDD Supply current (four amplifiers) VO = 0 No load25°C 160 250

µAIDD Supply current (four amplifiers) VO = 0, No loadFull range 300

µA

† Full range is 0°C to 70°C.NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated

to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

Page 13: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

13POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

operating characteristics at specified free-air temperature, VDD± = ±5 V

PARAMETER TEST CONDITIONS T †TLC2254C

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX

UNIT

SR Slew rate at unity gainVO = ±1.9 V, RL = 100 kΩ, 25°C 0.07 0.12

V/µsSR Slew rate at unity gain O ,CL = 100 pF

L ,

Full range 0.05V/µs

V Equivalent input noise voltagef = 10 Hz 25°C 38

nV/√HzVn Equivalent input noise voltagef = 1 kHz 25°C 19

nV/√Hz

VN(PP) Peak to peak equivalent input noise voltagef = 0.1 Hz to 1 Hz 25°C 0.8

µVVN(PP) Peak-to-peak equivalent input noise voltagef = 0.1 Hz to 10 Hz 25°C 1.1

µV

In Equivalent input noise current 25°C 0.6 fA /√Hz

THD + N Total harmonic distortion plus noiseVO = ± 2.3 V,f 20 kHz

AV = 125°C

0.2%THD + N Total harmonic distortion plus noise f = 20 kHz,

RL = 50 kΩ AV = 1025°C

1%

Gain-bandwidth productf = 10 kHz,CL = 100 pF

RL = 50 kΩ,25°C 0.21 MHz

BOM Maximum output-swing bandwidthVO(PP) = 4.6 V,RL = 50 kΩ,

AV = 1,CL = 100 pF

25°C 14 kHz

φm Phase margin at unity gainRL = 50 kΩ CL = 100 pF

25°C 63°

Gain marginRL = 50 kΩ, CL = 100 pF

25°C 15 dB† Full range is 0°C to 70°C.

Page 14: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS T †TLC2252I TLC2252AI

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX

UNIT

VIO Input offset voltage

V V V

25°C 200 1500 200 850µVVIO Input offset voltage

V V V

Full range 1750 1000µV

αVIOTemperature coefficientof input offset voltage

V V V

25°Cto 85°C 0.5 0.5 µV/°C

Input offset voltagelong-term drift(see Note 4)

VDD± = ±2.5 V, VO = 0,VIC = 0, RS = 50 Ω 25°C 0.003 0.003 µV/mo

IIO Input offset current25°C 0.5 60 0.5 60

pAIIO Input offset currentFull range 1000 1000

pA

IIB Input bias current25°C 1 60 1 60

pAIIB Input bias currentFull range 1000 1000

pA

VICRCommon-mode input

RS = 50 Ω |VIO | ≤5 mV

25°C0to4

–0.3to

4.2

0to4

–0.3to

4.2VVICR voltage range RS = 50 Ω, |VIO | ≤5 mV

Full range0to

3.5

0to

3.5

V

IOH = –20 µA 25°C 4.98 4.98

VOHHigh-level output

IOH = 75 µA25°C 4.9 4.94 4.9 4.94

VVOHg

voltage IOH = –75 µAFull range 4.8 4.8

V

IOH = –150 µA 25°C 4.8 4.88 4.8 4.88

VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01

Low level output VIC = 2 5 V IOL = 500 µA25°C 0.09 0.15 0.09 0.15

VOLLow-level outputvoltage

VIC = 2.5 V, IOL = 500 µAFull range 0.15 0.15 V

voltage

VIC = 2 5 V IOL = 4 A25°C 0.8 1 0.7 1

VIC = 2.5 V, IOL = 4 AFull range 1.2 1.2

Large signal differential V 2 5 V RL 100 kΩ‡25°C 100 350 100 350

AVDLarge-signal differentialvoltage amplification

VIC = 2.5 V,VO = 1 V to 4 V

RL = 100 kهFull range 10 10 V/mVVD voltage am lification VO = 1 V to 4 V

RL = 1 MΩ‡ 25°C 1700 1700

ridDifferential inputresistance

25°C 1012 1012 Ω

ricCommon-mode input resistance

25°C 1012 1012 Ω

cicCommon-mode input capacitance

f = 10 kHz, P package 25°C 8 8 pF

zoClosed-loopoutput impedance

f = 25 kHz, AV = 10 25°C 200 200 Ω

CMRRCommon-mode VIC = 0 to 2.7 V, VO = 2.5 V, 25°C 70 83 70 83

dBCMRR rejection ratioIC , O ,

RS = 50 Ω Full range 70 70dB

kSVR

Supply-voltage rejection ratio

VDD = 4.4 V to 16 V, 25°C 80 95 80 95dBkSVR rejection ratio

(∆VDD/∆VIO)

DDVIC = VDD/2, No load Full range 80 80

dB

IDD Supply current VO = 2 5 V No load25°C 70 125 70 125

µAIDD Su ly current VO = 2.5 V, No loadFull range 150 150

µA

† Full range is – 40°C to 125°C.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated

to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

Page 15: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

15POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

operating characteristics at specified free-air temperature, VDD = 5 V

PARAMETER TEST CONDITIONS T †TLC2252I TLC2252AI

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX

UNIT

Slew rate at unityVO = 1.5 V to 3.5 V, RL = 100 kΩ‡, 25°C 0.07 0.12 0.07 0.12

SRSlew rate at unitygain

O , L ,CL = 100 pF‡ Full

range0.05 0.05

V/µs

VEquivalent input f = 10 Hz 25°C 36 36

nV/√HzVnq

noise voltage f = 1 kHz 25°C 19 19nV/√Hz

VN(PP)

Peak-to-peakequivalent input

f = 0.1 Hz to 1 Hz 25°C 0.7 0.7µVVN(PP) equivalent input

noise voltage f = 0.1 Hz to 10 Hz 25°C 1.1 1.1µV

InEquivalent inputnoise current

25°C 0.6 0.6 fA√Hz

THD + NTotal harmonicdistortion plus

VO = 0.5 V to 2.5 V,f 10 kHz

AV = 125°C

0.2% 0.2%THD + N distortion plus

noisef = 10 kHz,RL = 50 kه AV = 10

25°C1% 1%

Gain-bandwidthproduct

f = 50 kHz,CL = 100 pF‡

RL = 50 kΩ‡, 25°C 0.2 0.2 MHz

BOMMaximum output-swing bandwidth

VO(PP) = 2 V, RL = 50 kه,

AV = 1,RL = 50 kه,

25°C 30 30 kHz

φmPhase margin atunity gain RL = 50 kΩ‡, CL = 100 pF‡

25°C 63° 63°

Gain marginL , L

25°C 15 15 dB† Full range is – 40°C to 125°C.‡ Referenced to 2.5 V

Page 16: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS T †TLC2252I TLC2252AI

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX

UNIT

VIO Input offset voltage

V V

25°C 200 1500 200 850µVVIO Input offset voltage

V V

Full range 1750 1000µV

αVIOTemperature coefficient ofinput offset voltage

V V

25°Cto 85°C 0.5 0.5 µV/°C

Input offset voltage long-term drift (see Note 4)

VIC = 0, VO = 0,RS = 50 Ω

25°C 0.003 0.003 µV/mo

IIO Input offset current

S25°C 0.5 60 0.5 60

pAIIO Input offset currentFull range 1000 1000

pA

IIB Input bias current25°C 1 60 1 60

pAIIB Input bias currentFull range 1000 1000

pA

VICRCommon-mode input

RS = 50 Ω |VIO | ≤5 mV

25°C–5to4

–5.3to

4.2

–5to4

–5.3to

4.2VVICR voltage range

RS = 50 Ω, |VIO | ≤5 mV

Full range–5to

3.5

–5to

3.5

V

IO = –20 µA 25°C 4.98 4.98

VOMMaximum positive peak

IO = 100 µA25°C 4.9 4.93 4.9 4.93

VVOM+ output voltageIO = –100 µA

Full range 4.7 4.7V

IO = –200 µA 25°C 4.8 4.86 4.8 4.86

VIC = 0, IO = 50 µA 25°C –4.99 –4.99

M i ti VIC = 0 IO = 500 µA25°C –4.85 –4.91 –4.85 –4.91

VOM–Maximum negativepeak output voltage

VIC = 0, IO = 500 µAFull range –4.85 –4.85 V

eak out ut voltage

VIC = 0 IO = 4 A25°C –4 –4.3 –4 –4.3

VIC = 0, IO = 4 AFull range –3.8 –3.8

L i l diff ti l RL = 50 kΩ25°C 40 150 40 150

AVDLarge-signal differentialvoltage amplification

VO = ±4 VRL = 50 kΩ

Full range 10 10 V/mVvoltage am lification

RL = 1 MΩ 25°C 3000 3000

ridDifferential inputresistance

25°C 1012 1012 Ω

ricCommon-mode inputresistance

25°C 1012 1012 Ω

cicCommon-mode inputcapacitance

f = 10 kHz, P package 25°C 8 8 pF

zoClosed-loop output impedance

f = 25 kHz, AV = 10 25°C 190 190 Ω

CMRRCommon-mode VIC = –5 V to 2.7 V, 25°C 75 88 75 88

dBCMRRrejection ratio

IC ,VO = 0, RS = 50 Ω Full range 75 75

dB

kSVRSupply-voltage rejection VDD = 4.4 V to 16 V, 25°C 80 95 80 95

dBkSVRy g j

ratio (∆VDD± /∆VIO)DD ,

VIC = VDD/2, No load Full range 80 80dB

IDD Supply current VO = 2 5 V No load25°C 80 125 80 125

µAIDD Supply current VO = 2.5 V, No loadFull range 150 150

µA

† Full range is – 40°C to 125°C.NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated

to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

Page 17: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

17POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

operating characteristics at specified free-air temperature, VDD± = ±5 V

PARAMETER TEST CONDITIONS T †TLC2252I TLC2252AI

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX

UNIT

VO = ±1 9 V RL = 100 kΩ25°C 0.07 0.12 0.07 0.12

SR Slew rate at unity gainVO = ±1.9 V, RL = 100 kΩ,CL = 100 pF Full

range0.05 0.05

V/µs

VEquivalent input noise f = 10 Hz 25°C 38 38

nV/√HzVnq

voltage f = 1 kHz 25°C 19 19nV/√Hz

VN(PP)Peak-to-peak equivalent f = 0.1 Hz to 1 Hz 25°C 0.8 0.8

µVVN(PP)q

input noise voltage f = 0.1 Hz to 10 Hz 25°C 1.1 1.1µV

InEquivalent input noisecurrent

25°C 0.6 0.6 fA√Hz

THD + NTotal harmonic distortion

VO = ±2.3 V,RL 50 kΩ

AV = 125°C

0.2% 0.2%THD + N

plus noiseRL = 50 kΩ,f = 10 kHz AV = 10

25°C1% 1%

Gain-bandwidth productf =10 kHz, RL = 50 kΩ,CL = 100 pF

25°C 0.21 0.21 MHz

BOMMaximum output-swingbandwidth

VO(PP) = 4.6 V, AV = 1,RL = 50 kΩ, CL = 100 pF

25°C 14 14 kHz

φmPhase margin at unitygain RL = 50 kΩ, CL = 100 pF

25°C 63° 63°

Gain marginL L

25°C 15 15 dB

† Full range is –40°C to 125°C.

Page 18: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

18 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS T †TLC2254I TLC2254AI

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX

UNIT

VIO Input offset voltage25°C 200 1500 200 850

µVVIO In ut offset voltageFull range 1750 1000

µV

αVIO

Temperaturecoefficient of inputoffset voltage VDD± = ±2.5 V,

25°Cto 125°C 0.5 0.5 µV/°C

Input offset voltagelong-term drift(see Note 4)

VDD± = ±2.5 V,VIC = 0,VO = 0,RS = 50 Ω

25°C 0.003 0.003 µV/mo

IIO Input offset current

S25°C 0.5 60 0.5 60

pAIIO In ut offset currentFull range 1000 1000

A

IIB Input bias current25°C 1 60 1 60

pAIIB In ut bias currentFull range 1000 1000

A

VICRCommon-mode input

RS = 50 Ω |VIO | ≤5 mV

25°C0to4

–0.3to

4.2

0to4

–0.3to

4.2VVICR voltage range

RS = 50 Ω, |VIO | ≤5 mV

Full range0to

3.5

0to

3.5

V

IOH = –20 µA 25°C 4.98 4.98

VOHHigh-level output

IOH = –75 µA25°C 4.9 4.94 4.9 4.94

VVOHg

voltageIOH = –75 µA

Full range 4.8 4.8V

IOH = –150 µA 25°C 4.8 4.88 4.8 4.88

VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01

Low level output VIC = 2 5 V IOL = 500 µA25°C 0.09 0.15 0.09 0.15

VOLLow-level outputvoltage

VIC = 2.5 V, IOL = 500 µAFull range 0.15 0.15 Vvoltage

VIC = 2 5 V IOL = 4 A25°C 0.8 1 0.7 1

VIC = 2.5 V, IOL = 4 AFull range 1.2 1.2

Large-signalV 2 5 V RL 100 kه

25°C 100 350 100 350

AVD

Large signaldifferential

VIC = 2.5 V,VO = 1 V to 4 V

RL = 100 kهFull range 10 10 V/mV

voltage amplificationVO = 1 V to 4 V

RL = 1 MΩ‡ 25°C 1700 1700

ri(d)Differential inputresistance

25°C 1012 1012 Ω

ri(c)Common-mode inputresistance

25°C 1012 1012 Ω

ci(c)Common-mode inputcapacitance

f = 10 kHz, N package 25°C 8 8 pF

zoClosed-loop outputimpedance

f = 25 kHz, AV = 10 25°C 200 200 Ω

CMRRCommon-mode VIC = 0 to 2.7 V, VO = 2.5 V, 25°C 70 83 70 83

dBCMRRrejection ratio

IC ORS = 50 Ω Full range 70 70

dB

kSVR

Supply-voltagerejection ratio

VDD = 4.4 V to 16 V, 25°C 80 95 80 95dBkSVR rejection ratio

(∆VDD/∆VIO)

DDVIC = VDD/2, No load Full range 80 80

dB

IDDSupply current

VO = 2 5 V No load25°C 140 250 140 250

µAIDDy

(four amplifiers)VO = 2.5 V, No load

Full range 300 300µA

† Full range is – 40°C to 125°C.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated

to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

Page 19: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

19POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

operating characteristics at specified free-air temperature, VDD = 5 V

PARAMETER TEST CONDITIONS T †TLC2254I TLC2254AI

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX

UNIT

Slew rate at unityVO = 1.4 V to 2.6 V, 25°C 0.07 0.12 0.07 0.12

SRSlew rate at unitygain

O ,RL = 100 kΩ‡,CL = 100 pF‡

Fullrange

0.05 0.05V/µs

VEquivalent input f = 10 Hz 25°C 36 36

nV/√HzVnq

noise voltage f = 1 kHz 25°C 19 19nV/√Hz

VN(PP)

Peak-to-peakequivalent input

f = 0.1 Hz to 1 Hz 25°C 0.7 0.7µVVN(PP) equivalent input

noise voltage f = 0.1 Hz to 10 Hz 25°C 1.1 1.1µV

InEquivalent inputnoise current

25°C 0.6 0.6 fA /√Hz

THD + NTotal harmonicdistortion plus

VO = 0.5 V to 2.5 V,f 20 kHz

AV = 125°C

0.2% 0.2%THD + N distortion plus

noisef = 20 kHz,RL = 50 kه AV = 10

25°C1% 1%

Gain-bandwidthproduct

f = 50 kHz,CL = 100 pF‡

RL = 50 kΩ‡, 25°C 0.2 0.2 MHz

BOMMaximum output-swing bandwidth

VO(PP) = 2 V,RL = 50 kه,

AV = 1,CL = 100 pF‡ 25°C 30 30 kHz

φmPhase margin atunity gain RL = 50 kΩ‡, CL = 100 pF‡

25°C 63° 63°

Gain marginL , L

25°C 15 15 dB† Full range is – 40°C to 125°C.‡ Referenced to 2.5 V

Page 20: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

20 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS T †TLC2254I TLC2254AI

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX

UNIT

VIO Input offset voltage25°C 200 1500 200 850

µVVIO Input offset voltageFull range 1750 1000

µV

αVIOTemperature coefficient ofinput offset voltage

25°Cto 125°C 0.5 0.5 µV/°C

Input offset voltagelong-term drift (see Note 4)

VIC = 0,RS = 50 Ω

VO = 0, 25°C 0.003 0.003 µV/mo

IIO Input offset current

S25°C 0.5 60 0.5 60

pAIIO Input offset currentFull range 1000 1000

pA

IIB Input bias current25°C 1 60 1 60

pAIIB Input bias currentFull range 1000 1000

pA

VICRCommon-mode input

RS = 50 Ω |VIO | ≤5 mV

25°C–5to4

–5.3to

4.2

–5to4

–5.3to

4.2VVICR voltage range

RS = 50 Ω, |VIO | ≤5 mV

Full range–5to

3.5

–5to

3.5

V

IO = –20 µA 25°C 4.98 4.98

VOMMaximum positive peak

IO = 100 µA25°C 4.9 4.93 4.9 4.93

VVOM+ output voltageIO = –100 µA

Full range 4.7 4.7V

IO = –200 µA 25°C 4.8 4.86 4.8 4.86

VIC = 0, IO = 50 µA 25°C –4.99 –4.99

M i ti k VIC = 0 IO = 500 µA25°C –4.85 –4.91 –4.85 –4.91

VOM–Maximum negative peakoutput voltage

VIC = 0, IO = 500 µAFull range –4.85 –4.85 V

out ut voltage

VIC = 0 IO = 4 A25°C –4 –4.3 –4 –4.3

VIC = 0, IO = 4 AFull range –3.8 –3.8

L i l diff ti l RL = 100 kΩ25°C 40 150 40 150

AVDLarge-signal differentialvoltage amplification

VO = ±4 VRL = 100 kΩ

Full range 10 10 V/mVvoltage am lification

RL = 1 MΩ 25°C 3000 3000

ri(d) Differential input resistance 25°C 1012 1012 Ω

ri(c)Common-mode inputresistance

25°C 1012 1012 Ω

ci(c)Common-mode inputcapacitance

f = 10 kHz, N package 25°C 8 8 pF

zoClosed-loop outputimpedance

f = 25 kHz, AV = 10 25°C 190 190 Ω

CMRRCommon-mode rejection VIC = –5 V to 2.7 V, 25°C 75 88 75 88

dBCMRRj

ratioIC ,

VO = 0, RS = 50 Ω Full range 75 75dB

kSVRSupply-voltage rejection VDD± = ±2.2 V to ±8 V, 25°C 80 95 80 95

dBkSVRy g j

ratio (∆VDD± /∆VIO)DD± ,

VIC = VDD/2, No load Full range 80 80dB

IDDSupply current

VO = 0 No load25°C 160 250 160 250

µAIDDy

(four amplifiers)VO = 0, No load

Full range 300 300µA

† Full range is – 40°C to 125°C.NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated

to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

Page 21: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

21POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

operating characteristics at specified free-air temperature, VDD± = ±5 V

PARAMETER TEST CONDITIONS T †TLC2254I TLC2254AI

UNITPARAMETER TEST CONDITIONS TA†MIN TYP MAX MIN TYP MAX

UNIT

VO = ±1 9 V RL = 100 kΩ25°C 0.07 0.12 0.07 0.12

SR Slew rate at unity gainVO = ±1.9 V,CL = 100 pF

RL = 100 kΩ,Full

range0.05 0.05

V/µs

VEquivalent input noise f = 10 Hz 25°C 38 38

nV/√HzVnq

voltage f = 1 kHz 25°C 19 19nV/√Hz

VN(PP)

Peak-to-peakequivalent input noise

f = 0.1 Hz to 1 Hz 25°C 0.8 0.8µVVN(PP) equivalent input noise

voltage f = 0.1 Hz to 10 Hz 25°C 1.1 1.1µV

InEquivalent input noisecurrent

25°C 0.6 0.6 fA /√Hz

THD + NTotal harmonic

VO = ±2.3 V,RL 50 kΩ

AV = 125°C

0.2% 0.2%THD + N

distortion plus noiseRL = 50 kΩ,f = 20 kHz AV = 10

25°C1% 1%

Gain-bandwidth productf =10 kHz,CL = 100 pF

RL = 50 kΩ,25°C 0.21 0.21 MHz

BOMMaximum output-swingbandwidth

VO(PP) = 4.6 V,RL = 50 kΩ,

AV = 1,CL = 100 pF

25°C 14 14 kHz

φmPhase margin at unitygain RL = 50 kΩ, CL = 100 pF

25°C 63° 63°

Gain marginL L

25°C 15 15 dB† Full range is –40°C to 125°C.

Page 22: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

22 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS TA†TLC2252QTLC2252M

TLC2252AQTLC2252AM UNITA

MIN TYP MAX MIN TYP MAX

VIO Input offset voltage

V V V

25°C 200 1500 200 850µVVIO Input offset voltage

V V V

Full range 1750 1000µV

αVIOTemperature coefficientof input offset voltage

V V V

25°Cto 125°C 0.5 0.5 µV/°C

Input offset voltagelong-term drift(see Note 4)

VDD± = ±2.5 V,VO = 0,

VIC = 0,RS = 50 Ω 25°C 0.003 0.003 µV/mo

IIO Input offset current25°C 0.5 60 0.5 60

pAIIO Input offset currentFull range 1000 1000

pA

IIB Input bias current25°C 1 60 1 60

pAIIB Input bias currentFull range 1000 1000

pA

VICRCommon-mode input

RS = 50 Ω |VIO | ≤5 mV

25°C0to4

–0.3to

4.2

0to4

–0.3to

4.2VVICR voltage range RS = 50 Ω, |VIO | ≤5 mV

Full range0to

3.5

0to

3.5

V

IOH = –20 µA 25°C 4.98 4.98

VOHHigh-level output

IOH = 75 µA25°C 4.9 4.94 4.9 4.94

VVOHg

voltage IOH = –75 µAFull range 4.8 4.8

V

IOH = –150 µA 25°C 4.8 4.88 4.8 4.88

VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01

Low level output VIC = 2 5 V IOL = 500 µA25°C 0.09 0.15 0.09 0.15

VOLLow-level outputvoltage

VIC = 2.5 V, IOL = 500 µAFull range 0.15 0.15 V

voltage

VIC = 2 5 V IOL = 4 A25°C 0.8 1 0.7 1

VIC = 2.5 V, IOL = 4 AFull range 1.2 1.2

Large signal differential V 2 5 V RL 100 kΩ‡25°C 100 350 100 350

AVDLarge-signal differentialvoltage amplification

VIC = 2.5 V,VO = 1 V to 4 V

RL = 100 kهFull range 10 10 V/mVVD voltage am lification VO = 1 V to 4 V

RL = 1 MΩ‡ 25°C 1700 1700

ridDifferential input resistance

25°C 1012 1012 Ω

ricCommon-mode inputresistance

25°C 1012 1012 Ω

cicCommon-mode inputcapacitance

f = 10 kHz, f = 10 kHz, 25°C 8 8 pF

zoClosed-loop output impedance

f = 25 kHz, AV = 10 25°C 200 200 Ω

CMRRCommon-mode VIC = 0 to 2.7 V, VO = 2.5 V, 25°C 70 83 70 83

dBCMRR rejection ratioIC ,

RS = 50 ΩO ,

Full range 70 70dB

kSVR

Supply-voltage rejection ratio

VDD = 4.4 V to 16 V, 25°C 80 95 80 95dBkSVR rejection ratio

(∆VDD/∆VIO)

DDVIC = VDD/2, No load Full range 80 80

dB

IDD Supply current VO = 2 5 V No load25°C 70 125 70 125

µAIDD Su ly current VO = 2.5 V, No loadFull range 150 150

µA

† Full range is – 40°C to 125°C for Q suffix, – 55°C to 125°C for M suffix.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated

to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

Page 23: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

23POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

operating characteristics at specified free-air temperature, VDD = 5 V

PARAMETER TEST CONDITIONS TA†TLC2252QTLC2252M

TLC2252AQTLC2252AM UNITA

MIN TYP MAX MIN TYP MAX

Slew rate at unity VO = 0 5 V to 3 5 V25°C 0.07 0.12 0.07 0.12

SRSlew rate at unitygain

VO = 0.5 V to 3.5 V,RL = 100 kΩ‡, CL = 100 pF‡ Full

range0.05 0.05

V/µs

VEquivalent input f = 10 Hz 25°C 36 36

nV/√HzVnq

noise voltage f = 1 kHz 25°C 19 19nV/√Hz

VN(PP)

Peak-to-peakequivalent input

f = 0.1 Hz to 1 Hz 25°C 0.7 0.7µVVN(PP) equivalent input

noise voltage f = 0.1 Hz to 10 Hz 25°C 1.1 1.1µV

InEquivalent inputnoise current

25°C 0.6 0.6 fA√Hz

THD + NTotal harmonicdistortion plus

VO = 0.5 V to 2.5 V,f 10 kHz

AV = 125°C

0.2% 0.2%THD + N distortion plus

noisef = 10 kHz,RL = 50 kه AV = 10

25°C1% 1%

Gain-bandwidthproduct

f = 50 kHz, RL = 50 kΩ‡,CL = 100 pF‡ 25°C 0.2 0.2 MHz

BOMMaximum output-swing bandwidth

VO(PP) = 2 V, AV = 1,RL = 50 kΩ‡, CL = 100 pF‡ 25°C 30 30 kHz

φmPhase margin atunity gain RL = 50 kΩ‡, CL = 100 pF‡

25°C 63° 63°

Gain marginL , L

25°C 15 15 dB† Full range is – 40°C to 125°C for Q suffix, – 55°C to 125°C for M suffix.‡ Referenced to 2.5 V

Page 24: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

24 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS TA†TLC2252QTLC2252M

TLC2252AQTLC2252AM UNITA

MIN TYP MAX MIN TYP MAX

VIO Input offset voltage

V V

25°C 200 1500 200 850µVVIO Input offset voltage

V V

Full range 1750 1000µV

αVIOTemperature coefficient ofinput offset voltage

V V

25°Cto 125°C 0.5 0.5 µV/°C

Input offset voltage long-term drift (see Note 4)

VIC = 0, VO = 0,RS = 50 Ω

25°C 0.003 0.003 µV/mo

IIO Input offset current

S25°C 0.5 60 0.5 60

pAIIO Input offset currentFull range 1000 1000

pA

IIB Input bias current25°C 1 60 1 60

pAIIB Input bias currentFull range 1000 1000

pA

VICRCommon-mode input

RS = 50 Ω |VIO | ≤5 mV

25°C–5to4

–5.3to

4.2

–5to4

–5.3to

4.2VVICR voltage range

RS = 50 Ω, |VIO | ≤5 mV

Full range–5to

3.5

–5to

3.5

V

IO = –20 µA 25°C 4.98 4.98

VOMMaximum positive peak

IO = 100 µA25°C 4.9 4.93 4.9 4.93

VVOM+ output voltageIO = –100 µA

Full range 4.7 4.7V

IO = –200 µA 25°C 4.8 4.86 4.8 4.86

VIC = 0, IO = 50 µA 25°C –4.99 –4.99

M i ti VIC = 0 IO = 500 µA25°C –4.85 –4.91 –4.85 –4.91

VOM–Maximum negativepeak output voltage

VIC = 0, IO = 500 µAFull range –4.85 –4.85 V

eak out ut voltage

VIC = 0 IO = 4 A25°C –4 –4.3 –4 –4.3

VIC = 0, IO = 4 AFull range –3.8 –3.8

L i l diff ti l RL = 100 kΩ25°C 40 150 40 150

AVDLarge-signal differentialvoltage amplification

VO = ±4 VRL = 100 kΩ

Full range 10 10 V/mVvoltage am lification

RL = 1 MΩ 25°C 3000 3000

ridDifferential inputresistance

25°C 1012 1012 Ω

ricCommon-mode inputresistance

25°C 1012 1012 Ω

cicCommon-mode inputcapacitance

f = 10 kHz, P package 25°C 8 8 pF

zoClosed-loop output impedance

f = 25 kHz, AV = 10 25°C 190 190 Ω

CMRRCommon-mode VIC = –5 V to 2.7 V, 25°C 75 88 75 88

dBCMRRrejection ratio

IC ,VO = 0, RS = 50 Ω Full range 75 75

dB

kSVRSupply-voltage rejection VDD = ±2.2 V to ±8 V, 25°C 80 95 80 95

dBkSVRy g j

ratio (∆VDD± /∆VIO)DD ,

VIC = 0, No load Full range 80 80dB

IDD Supply current VO = 2 5 V No load25°C 80 125 80 125

µAIDD Supply current VO = 2.5 V, No loadFull range 150 150

µA

† Full range is – 40°C to 125°C for Q suffix, – 55°C to 125°C for M suffix.NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated

to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

Page 25: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

25POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

operating characteristics at specified free-air temperature, VDD± = ±5 V

PARAMETER TEST CONDITIONS TA†TLC2252QTLC2252M

TLC2252AQTLC2252AM UNITA

MIN TYP MAX MIN TYP MAX

VO = ±2 V RL = 100 kΩ25°C 0.07 0.12 0.07 0.12

SR Slew rate at unity gainVO = ±2 V, RL = 100 kΩ,CL = 100 pF Full

range0.05 0.05

V/µs

VEquivalent input noise f = 10 Hz 25°C 38 38

nV/√HzVnq

voltage f = 1 kHz 25°C 19 19nV/√Hz

VN(PP)Peak-to-peak equivalent f = 0.1 Hz to 1 Hz 25°C 0.8 0.8

µVVN(PP)q

input noise voltage f = 0.1 Hz to 10 Hz 25°C 1.1 1.1µV

InEquivalent input noisecurrent

25°C 0.6 0.6 fA√Hz

THD + NTotal harmonic distortion

VO = ±2.3 V,RL 50 kΩ

AV = 125°C

0.2% 0.2%THD + N

plus noiseRL = 50 kΩ,f = 10 kHz AV = 10

25°C1% 1%

Gain-bandwidth productf =10 kHz, RL = 50 kΩ,CL = 100 pF

25°C 0.21 0.21 MHz

BOMMaximum output-swingbandwidth

VO(PP) = 4.6 V, AV = 1,RL = 50 kΩ, CL = 100 pF

25°C 14 14 kHz

φmPhase margin at unitygain RL = 50 kΩ, CL = 100 pF

25°C 63° 63°

Gain marginL L

25°C 15 15 dB† Full range is – 40°C to 125°C for Q suffix, – 55°C to 125°C for M suffix.

Page 26: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

26 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS TA†TLC2254QTLC2254M

TLC2254AQTLC2254AM UNITA

MIN TYP MAX MIN TYP MAX

VIO Input offset voltage25°C 200 1500 200 850

µVVIO In ut offset voltageFull range 1750 1000

µV

αVIO

Temperaturecoefficient of inputoffset voltage

25°Cto 125°C 0.5 0.5 µV/°C

Input offset voltagelong-term drift(see Note 4)

VDD± = ±2.5 V,VO = 0,

VIC = 0,RS = 50 Ω 25°C 0.003 0.003 µV/mo

IIO Input offset current25°C 0.5 60 0.5 60

pAIIO In ut offset current125°C 1000 1000

A

IIB Input bias current25°C 1 60 1 60

pAIIB In ut bias current125°C 1000 1000

A

VICRCommon-mode input

RS = 50 Ω |VIO | ≤5 mV

25°C0to4

–0.3to

4.2

0to4

–0.3to

4.2VVICR voltage range

RS = 50 Ω, |VIO | ≤5 mV

Full range0to

3.5

0to

3.5

V

IOH = –20 µA 25°C 4.98 4.98

VOHHigh-level output

IOH = –75 µA25°C 4.9 4.94 4.9 4.94

VVOHg

voltageIOH = –75 µA

Full range 4.8 4.8V

IOH = –150 µA 25°C 4.8 4.88 4.8 4.88

VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01

Low level output VIC = 2 5 V IOL = 500 µA25°C 0.09 0.15 0.09 0.15

VOLLow-level outputvoltage

VIC = 2.5 V, IOL = 500 µAFull range 0.15 0.15 Vvoltage

VIC = 2 5 V IOL = 4 A25°C 0.8 1 0.7 1

VIC = 2.5 V, IOL = 4 AFull range 1.2 1.2

Large-signalV 2 5 V RL 100 kه

25°C 100 350 100 350

AVD

Large signaldifferential

VIC = 2.5 V,VO = 1 V to 4 V

RL = 100 kهFull range 10 10 V/mV

voltage amplificationVO = 1 V to 4 V

RL = 1 MΩ‡ 25°C 1700 1700

ri(d)Differential inputresistance

25°C 1012 1012 Ω

ri(c)Common-mode inputresistance

25°C 1012 1012 Ω

ci(c)Common-mode inputcapacitance

f = 10 kHz, N package 25°C 8 8 pF

zoClosed-loop outputimpedance

f = 25 kHz, AV = 10 25°C 200 200 Ω

CMRRCommon-mode VIC = 0 to 2.7 V, VO = 2.5 V, 25°C 70 83 70 83

dBCMRRrejection ratio

IC ORS = 50 Ω Full range 70 70

dB

kSVR

Supply-voltagerejection ratio

VDD = 4.4 V to 16 V, 25°C 80 95 80 95dBkSVR rejection ratio

(∆VDD/∆VIO)

DDVIC = VDD/2, No load Full range 80 80

dB

IDDSupply current

VO = 2 5 V No load25°C 140 250 140 250

µAIDDy

(four amplifiers)VO = 2.5 V, No load

Full range 300 300µA

† Full range is – 40°C to 125°C for Q suffix, – 55°C to 125°C for M suffix.‡ Referenced to 2.5 VNOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated

to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

Page 27: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

27POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

operating characteristics at specified free-air temperature, VDD = 5 V

PARAMETER TEST CONDITIONS TA†TLC2254QTLC2254M

TLC2254AQTLC2254AM UNITA

MIN TYP MAX MIN TYP MAX

Slew rate at unityVO = 0.5 V to 3.5 V, 25°C 0.07 0.12 0.07 0.12

SRSlew rate at unitygain

O ,RL = 100 kΩ‡,CL = 100 pF‡

Fullrange

0.05 0.05V/µs

VEquivalent input f = 10 Hz 25°C 36 36

nV/√HzVnq

noise voltage f = 1 kHz 25°C 19 19nV/√Hz

VN(PP)

Peak-to-peakequivalent input

f = 0.1 Hz to 1 Hz 25°C 0.7 0.7µVVN(PP) equivalent input

noise voltage f = 0.1 Hz to 10 Hz 25°C 1.1 1.1µV

InEquivalent inputnoise current

25°C 0.6 0.6 fA /√Hz

THD + NTotal harmonicdistortion plus

VO = 0.5 V to 2.5 V,f 20 kHz

AV = 125°C

0.2% 0.2%THD + N distortion plus

noisef = 20 kHz,RL = 50 kه AV = 10

25°C1% 1%

Gain-bandwidthproduct

f = 50 kHz,CL = 100 pF‡

RL = 50 kΩ‡, 25°C 0.2 0.2 MHz

BOMMaximum output-swing bandwidth

VO(PP) = 2 V,RL = 50 kه,

AV = 1,CL = 100 pF‡ 25°C 30 30 kHz

φmPhase margin atunity gain RL = 50 kΩ‡, CL = 100 pF‡

25°C 63° 63°

Gain marginL , L

25°C 15 15 dB† Full range is – 40°C to 125°C for Q suffix, – 55°C to 125°C for M suffix.‡ Referenced to 2.5 V

Page 28: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

28 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

electrical characteristics at specified free-air temperature, VDD± = ±5 V (unless otherwise noted)

PARAMETER TEST CONDITIONS TA†TLC2254QTLC2254M

TLC2254AQTLC2254AM UNITA

MIN TYP MAX MIN TYP MAX

VIO Input offset voltage25°C 200 1500 200 850

µVVIO Input offset voltageFull range 1750 1000

µV

αVIOTemperature coefficient ofinput offset voltage

25°Cto 125°C 0.5 0.5 µV/°C

Input offset voltagelong-term drift (see Note 4)

VIC = 0,RS = 50 Ω

VO = 0, 25°C 0.003 0.003 µV/mo

IIO Input offset current

S25°C 0.5 60 0.5 60

pAIIO Input offset current125°C 1000 1000

pA

IIB Input bias current25°C 1 60 1 60

pAIIB Input bias current125°C 1000 1000

pA

VICRCommon-mode input

RS = 50 Ω |VIO | ≤5 mV

25°C–5to4

–5.3to

4.2

–5to4

–5.3to

4.2VVICR voltage range

RS = 50 Ω, |VIO | ≤5 mV

Full range–5to

3.5

–5to

3.5

V

IO = –20 µA 25°C 4.98 4.98

VOMMaximum positive peak

IO = 100 µA25°C 4.9 4.93 4.9 4.93

VVOM+ output voltageIO = –100 µA

Full range 4.7 4.7V

IO = –200 µA 25°C 4.8 4.86 4.8 4.86

VIC = 0, IO = 50 µA 25°C –4.99 –4.99

M i ti k VIC = 0 IO = 500 µA25°C –4.85 –4.91 –4.85 –4.91

VOM–Maximum negative peakoutput voltage

VIC = 0, IO = 500 µAFull range –4.85 –4.85 V

out ut voltage

VIC = 0 IO = 4 A25°C –4 –4.3 –4 –4.3

VIC = 0, IO = 4 AFull range –3.8 –3.8

L i l diff ti l RL = 100 kΩ25°C 40 150 40 150

AVDLarge-signal differentialvoltage amplification

VO = ±4 VRL = 100 kΩ

Full range 10 10 V/mVvoltage am lification

RL = 1 MΩ 25°C 3000 3000

ri(d) Differential input resistance 25°C 1012 1012 Ω

ri(c)Common-mode inputresistance

25°C 1012 1012 Ω

ci(c)Common-mode inputcapacitance

f = 10 kHz, N package 25°C 8 8 pF

zoClosed-loop outputimpedance

f = 25 kHz, AV = 10 25°C 190 190 Ω

CMRRCommon-mode rejection VIC = –5 V to 2.7 V, 25°C 75 88 75 88

dBCMRRj

ratioIC ,

VO = 0, RS = 50 Ω Full range 75 75dB

kSVRSupply-voltage rejection VDD± = ±2.2 V to ±8 V, 25°C 80 95 80 95

dBkSVRy g j

ratio (∆VDD± /∆VIO)DD± ,

VIC = VDD/2, No load Full range 80 80dB

IDDSupply current

VO = 0 No load25°C 160 250 160 250

µAIDDy

(four amplifiers)VO = 0, No load

Full range 300 300µA

† Full range is – 40°C to 125°C for Q suffix, – 55°C to 125°C for M suffix.NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated

to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.

Page 29: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

29POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

operating characteristics at specified free-air temperature, VDD± = ±5 V

PARAMETER TEST CONDITIONS TA†TLC2254QTLC2254M

TLC2254AQTLC2254AM UNITA

MIN TYP MAX MIN TYP MAX

VO = ±2 V RL = 100 kΩ25°C 0.07 0.12 0.07 0.12

SR Slew rate at unity gainVO = ±2 V,CL = 100 pF

RL = 100 kΩ,Full

range0.05 0.05

V/µs

VEquivalent input noise f = 10 Hz 25°C 38 38

nV/√HzVnq

voltage f = 1 kHz 25°C 19 19nV/√Hz

VN(PP)

Peak-to-peakequivalent input noise

f = 0.1 Hz to 1 Hz 25°C 0.8 0.8µVVN(PP) equivalent input noise

voltage f = 0.1 Hz to 10 Hz 25°C 1.1 1.1µV

InEquivalent input noisecurrent

25°C 0.6 0.6 fA /√Hz

THD + NTotal harmonic

VO = ±2.3 V,RL 50 kΩ

AV = 125°C

0.2% 0.2%THD + N

distortion plus noiseRL = 50 kΩ,f = 20 kHz AV = 10

25°C1% 1%

Gain-bandwidth productf =10 kHz,CL = 100 pF

RL = 50 kΩ,25°C 0.21 0.21 MHz

BOMMaximum output-swingbandwidth

VO(PP) = 4.6 V,RL = 50 kΩ,

AV = 1,CL = 100 pF

25°C 14 14 kHz

φmPhase margin at unitygain RL = 50 kΩ, CL = 100 pF

25°C 63° 63°

Gain marginL L

25°C 15 15 dB† Full range is – 40°C to 125°C for Q suffix, – 55°C to 125°C for M suffix.

Page 30: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

30 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS

Table of GraphsFIGURE

VIO Input offset voltageDistribution 2 – 5

VIO Input offset voltagevs Common-mode input voltage 6, 7

αVIO Input offset voltage temperature coefficient Distribution 8 – 11

IIB/IIO Input bias and input offset currents vs Free-air temperature 12

VI Input voltage rangevs Supply voltage 13

VI Input voltage rangey g

vs Free-air temperature 14

VOH High-level output voltage vs High-level output current 15

VOL Low-level output voltage vs Low-level output current 16, 17

VOM+ Maximum positive peak output voltage vs Output current 18

VOM– Maximum negative peak output voltage vs Output current 19

VO(PP) Maximum peak-to-peak output voltage vs Frequency 20

IOS Short circuit output currentvs Supply voltage 21

IOS Short-circuit output currenty g

vs Free-air temperature 22

VO Output voltage vs Differential input voltage 23, 24

Differential gain vs Load resistance 25

AVD Large signal differential voltage amplificationvs Frequency 26, 27

AVD Large-signal differential voltage amplificationq y

vs Free-air temperature,

28, 29

zo Output impedance vs Frequency 30, 31

CMRR Common mode rejection ratiovs Frequency 32

CMRR Common-mode rejection ratioq y

vs Free-air temperature 33

kSVR Supply voltage rejection ratiovs Frequency 34, 35

kSVR Supply-voltage rejection ratioq y

vs Free-air temperature,

36

IDD Supply currentvs Supply voltage 37

IDD Supply currenty g

vs Free-air temperature 38

SR Slew ratevs Load capacitance 39

SR Slew ratevs Free-air temperature 40

VO Inverting large-signal pulse response 41, 42

VO Voltage-follower large-signal pulse response 43, 44

VO Inverting small-signal pulse response 45, 46

VO Voltage-follower small-signal pulse response 47, 48

Vn Equivalent input noise voltage vs Frequency 49, 50

Noise voltage (referred to input) Over a 10-second period 51

Integrated noise voltage vs Frequency 52

THD + N Total harmonic distortion plus noise vs Frequency 53

Gain bandwidth productvs Free-air temperature 54

Gain-bandwidth productvs Supply voltage 55

φ Phase marginvs Frequency 26, 27φm Phase margin

q yvs Load capacitance

,56

Am Gain margin vs Load capacitance 57

B1 Unity-gain bandwidth vs Load capacitance 58

Overestimation of phase margin vs Load capacitance 59

Page 31: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

31POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS

Figure 2

Per

cen

tag

e o

f Am

plif

iers

– %

DISTRIBUTION OF TLC2252INPUT OFFSET VOLTAGE

VIO – Input Offset Voltage – mV

10

5

30

0

20

15

25

35

–1.6 –0.8 0 0.8 1.6

682 Amplifiers From 1 Wafer LotsVDD± = ± 2.5 VP PackageTA = 25°C

Figure 3

Per

cen

tag

e o

f Am

plif

iers

– %

DISTRIBUTION OF TLC2252INPUT OFFSET VOLTAGE

VIO – Input Offset Voltage – mV

10

5

30

0

20

15

25

35

–1.6 –0.8 0 0.8 1.6

682 Amplifiers From 1 Wafer LotsVDD± = ± 5 VP PackageTA = 25°C

Figure 4

Per

cen

tag

e o

f Am

plif

iers

– %

DISTRIBUTION OF TLC2254INPUT OFFSET VOLTAGE

VIO – Input Offset Voltage – mV

15

10

5

0

20

–1.6 0 0.8 1.6–0.8

1020 Amplifiers From 1 Wafer LotVDD = ±2.5 VTA = 25°C

Figure 5

Per

cen

tag

e o

f Am

plif

iers

– %

DISTRIBUTION OF TLC2254INPUT OFFSET VOLTAGE

VIO – Input Offset Voltage – mV

15

10

5

0

20

25

–1.6 0 0.8 1.6–0.8

1020 Amplifiers From 1 Wafer LotVDD± = ±5 VTA = 25°C

Page 32: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

32 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS

Figure 6

VIO

– In

pu

t O

ffse

t V

olt

age

– m

V

INPUT OFFSET VOLTAGE†

vsCOMMON-MODE INPUT VOLTAGE

ÁÁÁÁÁÁV

IO

VIC – Common-Mode Input Voltage – V

1

0.8

0.6

0.4

0.2

0

–0.2

–0.4

–0.6

–0.8

–1–1 0 1 2 3 4 5

VDD = 5 VRS = 50 ΩTA = 25°C

Figure 7

VIO

– In

pu

t O

ffse

t V

olt

age

– m

V

INPUT OFFSET VOLTAGEvs

COMMON-MODE INPUT VOLTAGE

ÁÁÁÁÁÁ

VIO

VIC – Common-Mode Input Voltage – V

VDD± = ±5 VRS = 50 ΩTA = 25°C

1

0.8

0.6

0.4

0.2

0

–0.2

–0.4

–0.6

–0.8

–1–6 –5 –4 –3 –2 –1 0 1 2 3 4 5

Figure 8

Pre

cen

tag

e o

f Am

plif

iers

– %

15

10

5

0

20

25

–1 0 1 2

P PackageTA = 25°C to 125°C

DISTRIBUTION OF TLC2252 INPUT OFFSETVOLTAGE TEMPERATURE COEFFICIENT

αVIO – Temperature Coefficient – µV/ °C

62 Amplifiers From1 Wafer LotVDD = ±2.5 V

Figure 9

Per

cen

tag

e o

f Am

plif

iers

– %

15

10

5

0

20

25

–1 0 1 2

62 Amplifiers From1 Wafer LotVDD = ±5 VP PackageTA = 25°C to 125°C

DISTRIBUTION OF TLC2252 INPUT OFFSETVOLTAGE TEMPERATURE COEFFICIENT

αVIO – Temperature Coefficient – µV/ °C

† For curves where VDD = 5 V, all loads are referenced to 2.5 V.

Page 33: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

33POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS

Figure 10

Per

cen

tag

e o

f Am

plif

iers

– %

DISTRIBUTION OF TLC2254 INPUT OFFSETVOLTAGE TEMPERATURE COEFFICIENT

αVIO – Temperature Coefficient ofInput Offset Voltage – µV/ °C

15

10

5

0

20

25

–2 –1 0 1 2

62 Amplifiers From1 Wafer LotVDD± = ± 2.5 VP PackageTA = 25°C to 125°C

Figure 11

Per

cen

tag

e o

f Am

plif

iers

– %

DISTRIBUTION OF TLC2254 INPUT OFFSETVOLTAGE TEMPERATURE COEFFICIENT

αVIO – Temperature Coefficient ofInput Offset Voltage – µV/ °C

15

10

5

0

20

25

–2 –1 0 1 2

62 Amplifiers From1 Wafer LotVDD± = ± 5 VP PackageTA = 25°C to 125°C

Figure 12

10

5

30

025 45 65 85IIB

an

d II

O –

Inp

ut

Bia

s an

d In

pu

t O

ffse

t C

urr

ents

– p

A

20

15

25

INPUT BIAS AND INPUT OFFSET CURRENTS†

vsFREE-AIR TEMPERATURE

35

105 125

IIB

IIO

VDD± = ±2.5 VVIC = 0VO = 0RS = 50 Ω

TA – Free-Air Temperature – °C

ÁÁÁÁ

I IBI IO

Figure 13

0

2 3 4 5

VI –

Inp

ut

Vo

ltag

e R

ang

e –

V

4

8

INPUT VOLTAGE RANGEvs

SUPPLY VOLTAGE10

6 7 8

6

2

–2

–4

–6

–8

–10

| VIO | ≤ 5 mV

RS = 50 ΩTA = 25°C

VI

| VDD± | – Supply Voltage – V

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

Page 34: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

34 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS

Figure 14

5

2

1

0

VI –

Inp

ut

Vo

ltag

e R

ang

e –

V

3

4

INPUT VOLTAGE RANGE†

vsFREE-AIR TEMPERATURE

5

–1–75 –55 –35 –15 25 45 65 85 105 125

VDD = 5 V

ÁÁÁÁ

VI

TA – Free-Air Temperature – °C

Figure 15

VO

H –

Hig

h-L

evel

Ou

tpu

t V

olt

age

– V

HIGH-LEVEL OUTPUT VOLTAGE†‡

vsHIGH-LEVEL OUTPUT CURRENT

| IOH| – High-Level Output Current – µA

ÁÁÁÁÁÁ

V OH

3

2

1

00 200 400

4

5

600 800

VDD = 5 V

TA = –40°C

TA = 25°C

TA = 125°C

TA = –55°C

Figure 16

0.6

0.4

0.2

00 1 2 3

VO

L –

Lo

w-L

evel

Ou

tpu

t V

olt

age

– V

0.8

1

LOW-LEVEL OUTPUT VOLTAGE‡

vsLOW-LEVEL OUTPUT CURRENT

1.2

4 5

VIC = 0VIC = 1.25 V

VIC = 2.5 V

VDD = 5 VTA = 25°C

ÁÁÁÁÁÁÁÁÁ

V OL

IOL – Low-Level Output Current – mA

Figure 17

0.8

0.4

0.2

00 1 2 3

VO

L –

Lo

w-L

evel

Ou

tpu

t V

olt

age

– V

1

1.2

LOW-LEVEL OUTPUT VOLTAGE†‡

vsLOW-LEVEL OUTPUT CURRENT

1.4

4 5 6

0.6

IOL – Low-Level Output Current – mA

TA = 125°C

TA = 25°C

TA = –55°C

VDD = 5 VVIC = 2.5 V

ÁÁÁÁÁÁ

V OL

TA = –40°C

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.‡ For curves where VDD = 5 V, all loads are referenced to 2.5 V.

Page 35: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

35POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS

Figure 18

MAXIMUM POSITIVE PEAK OUTPUT VOLTAGE†

vsOUTPUT CURRENT

IO – Output Current – µA

3

2

1

00 200 400

4

5

600 800

TA = 125°C

TA = 25°C

VO

M +

– M

axim

um

Po

siti

ve P

eak

Ou

tpu

t V

olt

age

– V

ÁÁÁÁÁÁ

VO

M +

TA = –40°C

VDD = ±5 V

TA = –55°C

Figure 19

0 1 2

VO

M –

– M

axim

um

Neg

ativ

e P

eak

Ou

tpu

t V

olt

age

– V

MAXIMUM NEGATIVE PEAK OUTPUT VOLTAGE†

vsOUTPUT CURRENT

3 4 5 6

–3.8

–4

–4.2

–4.4

–4.6

–4.8

–5

VDD± = ±5 VVIC = 0

TA = 125°C

TA = 25°C

TA = –40°C

IO – Output Current – mA

ÁÁÁÁÁÁ

VO

M –

TA = –55°C

Figure 20

VO

(PP

) –

Max

imu

m P

eak-

to-P

eak

Ou

tpu

t V

olt

age

– V

f – Frequency – Hz

MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE‡

vsFREQUENCY

ÁÁÁÁÁÁV

O(P

P)

6

5

3

1

0

10

4

8

7

9

2

102 103 104 105

VDD = 5 V

VDD± = ±5 VRL = 50 kΩTA = 25°C

Figure 21

IOS

– S

ho

rt-C

ircu

it O

utp

ut

Cu

rren

t –

mA

SHORT-CIRCUIT OUTPUT CURRENTvs

SUPPLY VOLTAGE

I OS

| VDD± | – Supply Voltage – V

5

3

1

2 3 4 5

7

8

10

6 7 8

9

6

4

2

0

–1

VID = –100 mV

VID = 100 mV

VO = 0TA = 25°CVIC = 0

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.‡ For curves where VDD = 5 V, all loads are referenced to 2.5 V.

Page 36: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

36 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS

Figure 22

IOS

– S

ho

rt-C

ircu

it O

utp

ut

Cu

rren

t –

mA

SHORT-CIRCUIT OUTPUT CURRENT†

vsFREE-AIR TEMPERATURE

TA – Free-Air Temperature – °C

I OS

11

10

9

8

7

6

5

4

3

2

1

0

–1–75 –50 –25 0 25 50 75 100 125

VID = –100 mV

VID = 100 mV

VO = 0VDD± = ±5 V

Figure 23

3

2

1

00 250

4

5

OUTPUT VOLTAGE‡

vsDIFFERENTIAL INPUT VOLTAGE

500 750 1000

VID – Differential Input Voltage – µV

– O

utp

ut

Vo

ltag

e –

VV

O

–1000 –750 –250–500

VDD = 5 VRL = 50 kΩVIC = 2.5 VTA = 25°C

Figure 24

1

–1

–3

–50 250

3

5

OUTPUT VOLTAGEvs

DIFFERENTIAL INPUT VOLTAGE

500 750 1000

VID – Differential Input Voltage – µV

VDD± = ±5 VVIC = 0RL = 50 kΩTA = 25°C

– O

utp

ut

Vo

ltag

e –

VV

O

–1000 –750 –250–500

Figure 25

Dif

fere

nti

al G

ain

– V

/ mV

DIFFERENTIAL GAIN‡

vsLOAD RESISTANCE

RL – Load Resistance – kΩ

104

103

102

101 101 102 103

VO (PP) = 2 VTA = 25°C

VDD = ±5 V

VDD = 5 V

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.‡ For curves where VDD = 5 V, all loads are referenced to 2.5 V.

Page 37: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

37POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS

om

– P

has

e M

arg

in

φ m

f – Frequency – Hz

LARGE-SIGNAL DIFFERENTIAL VOLTAGEAMPLIFICATION AND PHASE MARGIN†

vsFREQUENCY

AV

D –

Lar

ge-

Sig

nal

Dif

fere

nti

al

ÁÁÁÁÁÁ

AV

D Vo

ltag

e A

mp

lific

atio

n –

dB

20

80

60

40

0

–20

–40103 104 105 106 107

180°

135°

90°

45°

–45°

–90°

Gain

VDD = 5 VRL = 50 kΩCL= 100 pFTA = 25°C

Phase Margin

Figure 26

om

– P

has

e M

arg

in

φ m

f – Frequency – Hz

LARGE-SIGNAL DIFFERENTIAL VOLTAGEAMPLIFICATION AND PHASE MARGIN

vsFREQUENCY

AV

D –

Lar

ge-

Sig

nal

Dif

fere

nti

al

ÁÁÁÁÁÁ

AV

D Vo

ltag

e A

mp

lific

atio

n –

dB

20

80

60

40

0

–20

–40103 104 105 106 107

180°

135°

90°

45°

–45°

–90°

Gain

VDD = ±10 VRL= 50 kΩCL= 100 pFTA = 25°C

Phase Margin

Figure 27

† For curves where VDD = 5 V, all loads are referenced to 2.5 V.

Page 38: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

38 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS

Figure 28

LARGE-SIGNAL DIFFERENTIALVOLTAGE AMPLIFICATION†‡

vsFREE-AIR TEMPERATURE

TA – Free-Air Temperature – °C

AV

D –

Lar

ge-

Sig

nal

Dif

fere

nti

al

ÁÁ

AV

D Vo

ltag

e A

mp

lific

atio

n –

V/m

V

–50 –25 0 25 50 75 100 125

VDD = 5 VVIC = 2.5 VVO = 1 V to 4 V

RL = 50 kΩ

RL = 1 MΩ

104

103

102

–75101

Figure 29

TA – Free-Air Temperature – °C

LARGE-SIGNAL DIFFERENTIALVOLTAGE AMPLIFICATION†

vsFREE-AIR TEMPERATURE

AV

D –

Lar

ge-

Sig

nal

Dif

fere

nti

alÁÁÁÁ

AV

D Vo

ltag

e A

mp

lific

atio

n –

V/m

V

–50 –25 0 25 50 75 100 125

VDD± = ±5 VVIC = 0VO = ±4 V

RL = 50 kΩ

104

103

102

RL = 1 MΩ

–75101

Figure 30

zo –

Ou

tpu

t Im

ped

ance

– 0

OUTPUT IMPEDANCE‡

vsFREQUENCY

f – Frequency – Hz

Ωz o

10

1

0.1

1000

100

102 103 104 105 106

VDD = 5 VTA = 25°C

AV = 100

AV = 10

AV = 1

Figure 31

OUTPUT IMPEDANCEvs

FREQUENCY

f – Frequency – Hz

zo –

Ou

tpu

t Im

ped

ance

– 0 Ω

z o

10

1

0.1

1000

100

102 103 104 105 106

VDD± = ±5 VTA = 25°C

AV = 100

AV = 10

AV = 1

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.‡ For curves where VDD = 5 V, all loads are referenced to 2.5 V.

Page 39: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

39POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS

Figure 32

f – Frequency – Hz

COMMON-MODE REJECTION RATIO†

vsFREQUENCY

CM

RR

– C

om

mo

n-M

od

e R

ejec

tio

n R

atio

– d

B

80

40

20

0

100

60

101 102 103 104 105 166

VDD = 5 V

VDD± = ±5 V

Figure 33

COMMON-MODE REJECTION RATIO†‡

vsFREE-AIR TEMPERATURE

TA – Free-Air Temperature – °C

CM

RR

– C

om

mo

n-M

od

e R

ejec

tio

n R

atio

– d

B

84

82

92

80

88

86

90

94

–50 –25 0 25 50 75 100 125

VDD = 5 V

VDD± = ±5 V

–75

Figure 34

f – Frequency – Hz

SUPPLY-VOLTAGE REJECTION RATIO†

vsFREQUENCY

KS

VR

– S

up

ply

-Vo

ltag

e R

ejec

tio

n R

atio

– d

B

ÁÁÁÁÁÁ

kS

VR

100

80

60

40

20

0

–20101 102 103 104 105 106

kSVR–

VDD = 5 VTA = 25°CkSVR+

Figure 35

KS

VR

– S

up

ply

-Vo

ltag

e R

ejec

tio

n R

atio

– d

B

f – Frequency – Hz

SUPPLY-VOLTAGE REJECTION RATIOvs

FREQUENCY

ÁÁÁÁÁÁÁÁÁ

kS

VR

100

80

60

40

20

0

–20101 102 103 104 105 106

kSVR+

kSVR–

VDD± = ±5 VTA = 25°C

‡ Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

† For curves where VDD = 5 V, all loads are referenced to 2.5 V.

Page 40: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

40 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS

Figure 36

KS

VR

– S

up

ply

-Vo

ltag

e R

ejec

tio

n R

atio

– d

B

SUPPLY-VOLTAGE REJECTION RATIO†

vsFREE-AIR TEMPERATURE

ÁÁÁÁÁÁ

kS

VR

TA – Free-Air Temperature – °C

100

95

90

105

110

–50 –25 0 25 50 75 100 125

VDD± = ±2.2 V to ±8 VVO = 0

–75

Figure 37

IDD

– S

up

ply

Cu

rren

t –

uA

SUPPLY CURRENT†

vsSUPPLY VOLTAGE

| VDD± | – Supply Voltage – V

ÁÁÁÁÁÁ

I DD

120

80

40

00 1 2 3 4 5

160

200

240

6 7 8

TA = 25°C

TA = 125°C

VO = 0 No Load

TA = –55°C

TA = –40°C

Figure 38

SUPPLY CURRENT†‡

vsFREE-AIR TEMPERATURE

IDD

– S

up

ply

Cu

rren

t –

uA

ÁÁÁÁ

I DD

TA – Free-Air Temperature – °C

120

80

40

0

160

200

240

–50 –25 0 25 50 75 100 125

VDD± = ±5 VVO = 0

VDD = 5 VVO = 2.5 V

–75

Figure 39

SR

– S

lew

Rat

e –

v/u

s

SLEW RATE‡

vsLOAD CAPACITANCE

V/

CL – Load Capacitance – pF

0.16

0.08

0.04

0

0.2

0.12

101 102 103 104

VDD = 5 VAV = –1TA = 25°C

SR–

0.18

0.14

0.1

0.06

0.02

SR+

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.‡ For curves where VDD = 5 V, all loads are referenced to 2.5 V.

Page 41: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

41POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS

Figure 40

SLEW RATE†‡

vsFREE-AIR TEMPERATURE

TA – Free-Air Temperature – °C

SR

– S

lew

Rat

e –

v/u

ssµV

/

0.12

0.08

0.04

0

0.16

0.2

–50 –25 0 25 50 75 100 125

SR+

SR–

VDD = 5 VRL = 50 kΩCL = 100 pFAV = 1

–75

Figure 41

VO

– O

utp

ut

Vo

ltag

e –

V

INVERTING LARGE-SIGNAL PULSERESPONSE‡

VO

t – Time – µs

2

1

00 10 20 30 40 50 60

3

4

5

70 80 90 100

VDD = 5 VRL = 50 kΩCL = 100 pFAV = –1TA = 25°C

Figure 42

t – Time – µs

VO

– O

utp

ut

Vo

ltag

e –

VV

O

INVERTING LARGE-SIGNAL PULSERESPONSE

0

4

0 10 20 30 40 50 60

2

1

3

5

70 80 90 100

VDD± = ±5 VRL = 50 kΩCL = 100 pFAV = –1TA = 25°C

–1

–2

–3

–4

–5

Figure 43

VOLTAGE-FOLLOWER LARGE-SIGNALPULSE RESPONSE‡

t – Time – µs

VO

– O

utp

ut

Vo

ltag

e –

VV

O

2

1

00 10 20 30 40 50 60

3

4

5

70 80 90 100

VDD = 5 VRL = 50 kΩCL = 100 pFAV = 1TA = 25°C

† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.‡ For curves where VDD = 5 V, all loads are referenced to 2.5 V.

Page 42: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

42 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS

Figure 44

VO

– O

utp

ut

Vo

ltag

e –

VV

O

VOLTAGE-FOLLOWER LARGE-SIGNALPULSE RESPONSE

0

4

0 10 20 30 40 50 60

2

1

3

5

70 80 90 100

VDD± = ±5 VRL = 50 kΩCL = 100 pFAV = 1TA = 25°C

–1

–2

–3

–4

–5

t – Time – µs

Figure 45

INVERTING SMALL-SIGNALPULSE RESPONSE†

VO

– O

utp

ut

Vo

ltag

e –

VV

O

t – Time – µs

2.5

2.45

2.40 10 20 30

2.55

2.6

2.65

40 50

VDD = 5 VRL = 50 kΩCL = 100 pFAV = –1TA = 25°C

Figure 46

INVERTING SMALL-SIGNALPULSE RESPONSE

t – Time – µs

VO

– O

utp

ut

Vo

ltag

e –

mV

VO

0

0 10 20 30

0.1

40 50

0.05

–0.05

–0.1

VDD± = ±5 VRL = 50 kΩCL = 100 pFAV = –1TA = 25°C

Figure 47

VOLTAGE-FOLLOWER SMALL-SIGNALPULSE RESPONSE†

VO

– O

utp

ut

Vo

ltag

e –

VV

O

t – Time – µs

2.5

2.45

2.4

0 10 20 30

2.55

2.6

2.65

40 50

VDD = 5 VRL = 50 kΩCL = 100 pFAV = 1TA = 25°C

† For curves where VDD = 5 V, all loads are referenced to 2.5 V.

Page 43: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

43POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS

Figure 48

VOLTAGE-FOLLOWER SMALL-SIGNALPULSE RESPONSE

VO

– O

utp

ut

Vo

ltag

e –

VV

O

t – Time – µs0 10 20 30 40 50

VDD± = ±5 VRL = 50 kΩCL = 100 pFAV = 1TA = 25°C

–0.1

–0.05

0

0.05

0.1

Figure 49

VN

– E

qu

ival

ent

Inp

ut

No

ise

Vo

ltag

e –

nv/

/Hz

f – Frequency – Hz

EQUIVALENT INPUT NOISE VOLTAGE†

vsFREQUENCY

nV

/H

zV

n

40

20

10

0

60

30

50

101 102 103 104

VDD = 5 VRS = 20 ΩTA = 25°C

Figure 50

EQUIVALENT INPUT NOISE VOLTAGEvs

FREQUENCY

f – Frequency – Hz

VN

– E

qu

ival

ent

Inp

ut

No

ise

Vo

ltag

e –

nv/

/Hz

nV

/H

zV

n

40

20

10

0

60

30

50

101 102 103 104

VDD± = ±5 VRS = 20 ΩTA = 25°C

Figure 51

No

ise

Vo

ltag

e –

nV

t – Time – s

EQUIVALENT INPUT NOISE VOLTAGE OVERA 10-SECOND PERIOD†

0 2 4 6

0

750

1000

8 10

500

–250

–500

–750

–1000

250

VDD = 5 Vf = 0.1 Hz to 10 HzTA = 25°C

† For curves where VDD = 5 V, all loads are referenced to 2.5 V.

Page 44: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

44 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS

Figure 52

0.1

Inte

gra

ted

No

ise

Vo

ltag

e –

f – Frequency – Hz

INTEGRATED NOISE VOLTAGEvs

FREQUENCY

1

10

100

1 101 102 103 104 105

Calculated Using Ideal Pass-Band FilterLow Frequency = 1 HzTA = 25°CV

µ

Figure 53

TH

D +

N –

To

tal H

arm

on

ic D

isto

rtio

n P

lus

No

ise

– %

f – Frequency – Hz

TOTAL HARMONIC DISTORTION PLUS NOISE†

vsFREQUENCY

0.01

1

0.001101 102 103 104 105

AV = 10

AV = 1VDD = 5 VRL = 50 kΩTA = 25°C

0.1

AV = 100

Figure 54

Gai

n-B

and

wid

th P

rod

uct

– k

Hz

GAIN-BANDWIDTH PRODUCT†‡

vsFREE-AIR TEMPERATURE

TA – Free-Air Temperature – °C

200

120

80

240

280

–75 –25 0 25 50 75 100 125

VDD = 5 Vf = 10 kHzRL = 50 kΩCL = 100 pF

–50

160

Figure 55

Gai

n-B

and

wid

th P

rod

uct

– k

Hz

GAIN-BANDWIDTH PRODUCTvs

SUPPLY VOLTAGE

| VDD ± | – Supply Voltage – V

210

190

170

1500 2 3 5

230

250

7 81 4 6

TA = 25°C

‡ Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.

† For curves where VDD = 5 V, all loads are referenced to 2.5 V.

Page 45: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

45POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

TYPICAL CHARACTERISTICS

Figure 56

om

– P

has

e M

arg

in

PHASE MARGINvs

LOAD CAPACITANCE

CL – Load Capacitance – pF

101 102 103 105

75°

60°

45°

30°

15°

Rnull = 200 Ω

Rnull = 500 Ω

Rnull = 50 Ω

Rnull = 0

TA = 25°C

Rnull = 10 Ω

104

50 kΩ

50 kΩ

VDD –

VDD +Rnull

CLVI

+–

Rnull = 100 Ω

Figure 57

Gai

n M

arg

in –

dB

GAIN MARGINvs

LOAD CAPACITANCE

CL – Load Capacitance – pF

20

10

5

0

15

101 102 103 105

Rnull = 100 Ω

TA = 25°C

Rnull = 50 Ω

104

Rnull = 500 Ω

Rnull = 200 Ω

Rnull = 0

Rnull = 10 Ω

Figure 58

– U

nit

y-G

ain

Ban

dw

idth

– k

Hz

UNITY-GAIN BANDWIDTH†

vsLOAD CAPACITANCE

CL – Load Capacitance – pF

ÁÁÁÁ

B1

150

25

100

0

200

125

175

50

75

101 102 103 104 105

TA = 25°C

Figure 59

Ove

rest

imat

ion

of P

has

e M

arg

in

OVERESTIMATION OF PHASE MARGIN†

vsLOAD CAPACITANCE

CL – Load Capacitance – pF

15

10

5

0

20

25

101 102 103 104 105

TA = 25°C

Rnull = 100 Ω

Rnull = 50 Ω

Rnull = 10 Ω

Rnull = 500 Ω

Rnull = 200 Ω

† See application information

Page 46: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAILVERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

46 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

APPLICATION INFORMATION

driving large capacitive loads

The TLC225x is designed to drive larger capacitive loads than most CMOS operational amplifiers. Figure 56and Figure 57 illustrate its ability to drive loads up to 1000 pF while maintaining good gain and phase margins(Rnull = 0).

A smaller series resistor (Rnull) at the output of the device (see Figure 60) improves the gain and phase marginswhen driving large capacitive loads. Figure 56 and Figure 57 show the effects of adding series resistances of10 Ω , 50 Ω , 100 Ω , 200 Ω , and 500 Ω . The addition of this series resistor has two effects: the first is that it addsa zero to the transfer function and the second is that it reduces the frequency of the pole associated with theoutput load in the transfer function.

The zero introduced to the transfer function is equal to the series resistance times the load capacitance. Tocalculate the improvement in phase margin, equation 1 can be used.

∆φm1 tan–1 2 × π × UGBW × Rnull × CL

Where :

(1)

∆φm1 Improvement in phase margin

UGBW Unity-gain bandwidth frequency

Rnull Output series resistance

CL Load capacitance

The unity-gain bandwidth (UGBW) frequency decreases as the capacitive load increases (see Figure 58). Touse equation 1, UGBW must be approximated from Figure 58.

Using equation 1 alone overestimates the improvement in phase margin, as illustrated in Figure 59. Theoverestimation is caused by the decrease in the frequency of the pole associated with the load, thus providingadditional phase shift and reducing the overall improvement in phase margin.

Using Figure 60, with equation 1 enables the designer to choose the appropriate output series resistance tooptimize the design of circuits driving large capacitance loads.

50 kΩ

50 kΩ

VDD– /GND

VDD+

Rnull

CL

VI+

Figure 60. Series-Resistance Circuit

Page 47: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TLC225x, TLC225xAAdvanced LinCMOS RAIL-TO-RAIL

VERY LOW-POWER OPERATIONAL AMPLIFIERSSLOS176D – FEBRUARY 1997 – REVISED MARCH 2001

47POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

APPLICATION INFORMATION

macromodel information

Macromodel information provided was derived using MicroSim Parts , the model generation software usedwith MicroSim PSpice . The Boyle macromodel (see Note 5) and subcircuit in Figure 61 are generated usingthe TLC225x typical electrical and operating characteristics at TA = 25°C. Using this information, outputsimulations of the following key parameters can be generated to a tolerance of 20% (in most cases):

Maximum positive output voltage swing Maximum negative output voltage swing Slew rate Quiescent power dissipation Input bias current Open-loop voltage amplification

Unity-gain frequency Common-mode rejection ratio Phase margin DC output resistance AC output resistance Short-circuit output current limit

NOTE 5: G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Integrated Circuit Operational Amplifiers”, IEEE Journalof Solid-State Circuits, SC-9, 353 (1974).

OUT

+

+

+

+

+–

+

+

– +

+–

.SUBCKT TLC225x 1 2 3 4 5C1 11 12 6.369E–12C2 6 7 25.00E–12DC 5 53 DXDE 54 5 DXDLP 90 91 DXDLN 92 90 DXDP 4 3 DXEGND 99 0 POLY (2) (3,0) (4,0) 0 .5 .5FB 7 99 POLY (5) VB VC VE VLP+ VLN 0 57.62E6 –60E6 60E6 60E6 –60E6GA 6 0 11 12 26.86E–6GCM 0 6 10 99 2.686E–9ISS 3 10 DC 3.1E–6HLIM 90 0 VLIM 1KJ1 11 2 10 JXJ2 12 1 10 JXR2 6 9 100.0E3

RD1 60 11 37.23E3RD2 60 12 37.23E3R01 8 5 84R02 7 99 84RP 3 4 71.43E3RSS 10 99 64.52E6VAD 60 4 –.5VB 9 0 DC 0VC 3 53 DC .605VE 54 4 DC .605VLIM 7 8 DC 0VLP 91 0 DC –.235VLN 0 92 DC 7.5.MODEL DX D (IS=800.0E–18).MODEL JX PJF (IS=500.0E–15 BETA=139E–6+ VTO=–.05).ENDS

VCC+

RP

IN –2

IN+1

VCC–

VAD

RD1

11

J1 J2

10

RSS ISS

3

12

RD2

60

VE

54DE

DP

VC

DC

4

C1

53

R2

6

9

EGND

VB

FB

C2

GCM GA VLIM

8

5

RO1

RO2

HLIM

90

DLP

91

DLN

92

VLNVLP

99

7

Figure 61. Boyle Macromodel and Subcircuit

PSpice and Parts are trademarks of MicroSim Corporation.

Page 48: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

PACKAGE OPTION ADDENDUM

www.ti.com 17-Mar-2017

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status(1)

Package Type PackageDrawing

Pins PackageQty

Eco Plan(2)

Lead/Ball Finish(6)

MSL Peak Temp(3)

Op Temp (°C) Device Marking(4/5)

Samples

5962-9564001Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9564001Q2ATLC2252MFKB

5962-9564001QHA ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9564001QHATLC2252M

5962-9564001QPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9564001QPATLC2252M

5962-9564002Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9564002Q2ATLC2254MFKB

5962-9564002QDA ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9564002QDATLC2254MWB

5962-9564003NXD ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM -55 to 125 Q2252A

5962-9564003NXDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM -55 to 125 Q2252A

5962-9564003Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9564003Q2ATLC2252AMFKB

5962-9564003QHA ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9564003QHATLC2252AM

5962-9564003QPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9564003QPATLC2252AM

5962-9564004Q2A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9564004Q2ATLC2254AMFKB

5962-9564004QDA ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9564004QDATLC2254AMWB

TLC2252AID ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 2252AI

Page 49: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

PACKAGE OPTION ADDENDUM

www.ti.com 17-Mar-2017

Addendum-Page 2

Orderable Device Status(1)

Package Type PackageDrawing

Pins PackageQty

Eco Plan(2)

Lead/Ball Finish(6)

MSL Peak Temp(3)

Op Temp (°C) Device Marking(4/5)

Samples

TLC2252AIDG4 ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 2252AI

TLC2252AIDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 2252AI

TLC2252AIDRG4 ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 2252AI

TLC2252AIP ACTIVE PDIP P 8 50 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type TLC2252AI

TLC2252AIPE4 ACTIVE PDIP P 8 50 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type TLC2252AI

TLC2252AIPW ACTIVE TSSOP PW 8 150 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM Y2252A

TLC2252AIPWR ACTIVE TSSOP PW 8 2000 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM Y2252A

TLC2252AIPWRG4 ACTIVE TSSOP PW 8 2000 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM Y2252A

TLC2252AMFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9564003Q2ATLC2252AMFKB

TLC2252AMJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9564003QPATLC2252AM

TLC2252AMUB ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9564003QHATLC2252AM

TLC2252AQDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM -40 to 125 C2252A

TLC2252AQDRG4 ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM C2252A

TLC2252CD ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 0 to 70 2252C

TLC2252CDG4 ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 0 to 70 2252C

TLC2252CDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 0 to 70 2252C

TLC2252CDRG4 ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 0 to 70 2252C

Page 50: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

PACKAGE OPTION ADDENDUM

www.ti.com 17-Mar-2017

Addendum-Page 3

Orderable Device Status(1)

Package Type PackageDrawing

Pins PackageQty

Eco Plan(2)

Lead/Ball Finish(6)

MSL Peak Temp(3)

Op Temp (°C) Device Marking(4/5)

Samples

TLC2252CP ACTIVE PDIP P 8 50 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type 0 to 70 TLC2252CP

TLC2252CPW ACTIVE TSSOP PW 8 150 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2252

TLC2252CPWG4 ACTIVE TSSOP PW 8 150 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2252

TLC2252CPWR ACTIVE TSSOP PW 8 2000 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2252

TLC2252CPWRG4 ACTIVE TSSOP PW 8 2000 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2252

TLC2252ID ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM -40 to 125 2252I

TLC2252IDG4 ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM -40 to 125 2252I

TLC2252IDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM -40 to 125 2252I

TLC2252IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM -40 to 125 2252I

TLC2252IP ACTIVE PDIP P 8 50 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type -40 to 125 TLC2252IP

TLC2252MFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9564001Q2ATLC2252MFKB

TLC2252MJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type -55 to 125 9564001QPATLC2252M

TLC2252MUB ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type -55 to 125 9564001QHATLC2252M

TLC2254AID ACTIVE SOIC D 14 50 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 2254AI

TLC2254AIDG4 ACTIVE SOIC D 14 50 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 2254AI

TLC2254AIDR ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 2254AI

TLC2254AIDRG4 ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 2254AI

Page 51: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

PACKAGE OPTION ADDENDUM

www.ti.com 17-Mar-2017

Addendum-Page 4

Orderable Device Status(1)

Package Type PackageDrawing

Pins PackageQty

Eco Plan(2)

Lead/Ball Finish(6)

MSL Peak Temp(3)

Op Temp (°C) Device Marking(4/5)

Samples

TLC2254AIN ACTIVE PDIP N 14 25 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type TLC2254AIN

TLC2254AIPW ACTIVE TSSOP PW 14 90 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM Y2254A

TLC2254AIPWR ACTIVE TSSOP PW 14 2000 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM Y2254A

TLC2254AIPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM Y2254A

TLC2254AMFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9564004Q2ATLC2254AMFKB

TLC2254AMWB ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9564004QDATLC2254AMWB

TLC2254AQD ACTIVE SOIC D 14 50 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM -40 to 125 TLC2254A

TLC2254AQDR ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM -40 to 125 TLC2254A

TLC2254AQDRG4 ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM PJ2254A

TLC2254CD ACTIVE SOIC D 14 50 Green (RoHS& no Sb/Br)

CU NIPDAU | Call TI Level-1-260C-UNLIM 0 to 70 TLC2254C

TLC2254CDG4 ACTIVE SOIC D 14 50 Green (RoHS& no Sb/Br)

Call TI Level-1-260C-UNLIM 0 to 70 TLC2254C

TLC2254CDR ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 0 to 70 TLC2254C

TLC2254CDRG4 ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 0 to 70 TLC2254C

TLC2254CN ACTIVE PDIP N 14 25 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type 0 to 70 TLC2254CN

TLC2254CPW ACTIVE TSSOP PW 14 90 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2254

TLC2254CPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2254

TLC2254CPWR ACTIVE TSSOP PW 14 2000 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2254

Page 52: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

PACKAGE OPTION ADDENDUM

www.ti.com 17-Mar-2017

Addendum-Page 5

Orderable Device Status(1)

Package Type PackageDrawing

Pins PackageQty

Eco Plan(2)

Lead/Ball Finish(6)

MSL Peak Temp(3)

Op Temp (°C) Device Marking(4/5)

Samples

TLC2254CPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM 0 to 70 P2254

TLC2254ID ACTIVE SOIC D 14 50 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM TLC2254I

TLC2254IDG4 ACTIVE SOIC D 14 50 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM TLC2254I

TLC2254IDR ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM TLC2254I

TLC2254IDRG4 ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM TLC2254I

TLC2254IN ACTIVE PDIP N 14 25 Pb-Free(RoHS)

CU NIPDAU N / A for Pkg Type TLC2254IN

TLC2254MFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-9564002Q2ATLC2254MFKB

TLC2254MWB ACTIVE CFP W 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9564002QDATLC2254MWB

(1) The marketing status values are defined as follows:ACTIVE: Product device recommended for new designs.LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.PREVIEW: Device has been announced but is not in production. Samples may or may not be available.OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availabilityinformation and additional product content details.TBD: The Pb-Free/Green conversion plan has not been defined.Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement thatlead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used betweenthe die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weightin homogeneous material)

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

Page 53: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

PACKAGE OPTION ADDENDUM

www.ti.com 17-Mar-2017

Addendum-Page 6

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuationof the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finishvalue exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on informationprovided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken andcontinues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

OTHER QUALIFIED VERSIONS OF TLC2252, TLC2252A, TLC2252AM, TLC2252M, TLC2254, TLC2254A, TLC2254AM, TLC2254M :

• Catalog: TLC2252A, TLC2252, TLC2254A, TLC2254

• Automotive: TLC2252-Q1, TLC2252A-Q1, TLC2252A-Q1, TLC2252-Q1, TLC2254-Q1, TLC2254A-Q1, TLC2254A-Q1, TLC2254-Q1

• Enhanced Product: TLC2252A-EP, TLC2252A-EP, TLC2254A-EP, TLC2254A-EP

• Military: TLC2252M, TLC2252AM, TLC2254M, TLC2254AM

NOTE: Qualified Version Definitions:

• Catalog - TI's standard catalog product

• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects

• Enhanced Product - Supports Defense, Aerospace and Medical Applications

• Military - QML certified for Military and Defense Applications

Page 54: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device PackageType

PackageDrawing

Pins SPQ ReelDiameter

(mm)

ReelWidth

W1 (mm)

A0(mm)

B0(mm)

K0(mm)

P1(mm)

W(mm)

Pin1Quadrant

5962-9564003NXDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

TLC2252AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

TLC2252AIPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1

TLC2252AQDR SOIC D 8 2500 330.0 12.5 6.4 5.2 2.1 8.0 12.0 Q1

TLC2252CDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

TLC2252CPWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1

TLC2252IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

TLC2254AIDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1

TLC2254AIPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1

TLC2254AQDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1

TLC2254CDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1

TLC2254CPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1

TLC2254IDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 3-Aug-2018

Pack Materials-Page 1

Page 55: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

5962-9564003NXDR SOIC D 8 2500 367.0 367.0 38.0

TLC2252AIDR SOIC D 8 2500 340.5 338.1 20.6

TLC2252AIPWR TSSOP PW 8 2000 367.0 367.0 35.0

TLC2252AQDR SOIC D 8 2500 340.5 338.1 20.6

TLC2252CDR SOIC D 8 2500 340.5 338.1 20.6

TLC2252CPWR TSSOP PW 8 2000 367.0 367.0 35.0

TLC2252IDR SOIC D 8 2500 340.5 338.1 20.6

TLC2254AIDR SOIC D 14 2500 367.0 367.0 38.0

TLC2254AIPWR TSSOP PW 14 2000 367.0 367.0 35.0

TLC2254AQDR SOIC D 14 2500 367.0 367.0 38.0

TLC2254CDR SOIC D 14 2500 367.0 367.0 38.0

TLC2254CPWR TSSOP PW 14 2000 367.0 367.0 35.0

TLC2254IDR SOIC D 14 2500 367.0 367.0 38.0

PACKAGE MATERIALS INFORMATION

www.ti.com 3-Aug-2018

Pack Materials-Page 2

Page 56: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised
Page 57: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised
Page 58: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised
Page 59: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised
Page 60: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised
Page 61: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised
Page 62: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised
Page 63: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised
Page 64: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

MECHANICAL DATA

MCER001A – JANUARY 1995 – REVISED JANUARY 1997

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE

0.310 (7,87)0.290 (7,37)

0.014 (0,36)0.008 (0,20)

Seating Plane

4040107/C 08/96

5

40.065 (1,65)0.045 (1,14)

8

1

0.020 (0,51) MIN

0.400 (10,16)0.355 (9,00)

0.015 (0,38)0.023 (0,58)

0.063 (1,60)0.015 (0,38)

0.200 (5,08) MAX

0.130 (3,30) MIN

0.245 (6,22)0.280 (7,11)

0.100 (2,54)

0°–15°

NOTES: A. All linear dimensions are in inches (millimeters).B. This drawing is subject to change without notice.C. This package can be hermetically sealed with a ceramic lid using glass frit.D. Index point is provided on cap for terminal identification.E. Falls within MIL STD 1835 GDIP1-T8

Page 65: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised
Page 66: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised
Page 67: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

www.ti.com

PACKAGE OUTLINE

C

TYP6.66.2

1.2 MAX

6X 0.65

8X 0.300.19

2X1.95

0.150.05

(0.15) TYP

0 - 8

0.25GAGE PLANE

0.750.50

A

NOTE 3

3.12.9

BNOTE 4

4.54.3

4221848/A 02/2015

TSSOP - 1.2 mm max heightPW0008ASMALL OUTLINE PACKAGE

NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm per side. 4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.5. Reference JEDEC registration MO-153, variation AA.

18

0.1 C A B

54

PIN 1 IDAREA

SEATING PLANE

0.1 C

SEE DETAIL A

DETAIL ATYPICAL

SCALE 2.800

Page 68: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

www.ti.com

EXAMPLE BOARD LAYOUT

(5.8)

0.05 MAXALL AROUND

0.05 MINALL AROUND

8X (1.5)8X (0.45)

6X (0.65)

(R )TYP

0.05

4221848/A 02/2015

TSSOP - 1.2 mm max heightPW0008ASMALL OUTLINE PACKAGE

SYMM

SYMM

LAND PATTERN EXAMPLESCALE:10X

1

45

8

NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

METALSOLDER MASKOPENING

NON SOLDER MASKDEFINED

SOLDER MASK DETAILSNOT TO SCALE

SOLDER MASKOPENING

METAL UNDERSOLDER MASK

SOLDER MASKDEFINED

Page 69: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

www.ti.com

EXAMPLE STENCIL DESIGN

(5.8)

6X (0.65)

8X (0.45)8X (1.5)

(R ) TYP0.05

4221848/A 02/2015

TSSOP - 1.2 mm max heightPW0008ASMALL OUTLINE PACKAGE

NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design.

SYMM

SYMM

1

45

8

SOLDER PASTE EXAMPLEBASED ON 0.125 mm THICK STENCIL

SCALE:10X

Page 70: Advanced LinCMOS  Rail-to-Rail Very Low … · tlc225x, tlc225xa advanced lincmos rail-to-rail very low-power operational amplifiers slos176d – february 1997 – revised

IMPORTANT NOTICE

Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to itssemiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyersshould obtain the latest relevant information before placing orders and should verify that such information is current and complete.TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integratedcircuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products andservices.Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and isaccompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduceddocumentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statementsdifferent from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for theassociated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designersremain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers havefull and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI productsused in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, withrespect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerousconsequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm andtake appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer willthoroughly test such applications and the functionality of such TI products as used in such applications.TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended toassist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in anyway, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resourcesolely for this purpose and subject to the terms of this Notice.TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TIproducts, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specificallydescribed in the published documentation for a particular TI Resource.Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications thatinclude the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISETO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTYRIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, orother intellectual property right relating to any combination, machine, or process in which TI products or services are used. Informationregarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty orendorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of thethird party, or a license from TI under the patents or other intellectual property of TI.TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES ORREPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TOACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OFMERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUALPROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OFPRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES INCONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEENADVISED OF THE POSSIBILITY OF SUCH DAMAGES.Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, suchproducts are intended to help enable customers to design and create their own applications that meet applicable functional safety standardsand requirements. Using products in an application does not by itself establish any safety features in the application. Designers mustensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products inlife-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., lifesupport, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, allmedical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applicationsand that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatoryrequirements in connection with such selection.Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-compliance with the terms and provisions of this Notice.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2018, Texas Instruments Incorporated