Auto Cad Iso Drawing

Embed Size (px)

Text of Auto Cad Iso Drawing

OJT ReportAUTO CAD ISO DRAWING

Doc. No Rev. Date Page

POR-C-E015-01 0 26 Nov. 2008 1 of 17

AUTO ISO DRAWING

0 Rev.

2008.11.26 Date

Monthly Report Description

By

Remark

Related manual

Mentor

None

Writer

Department

Document No.

Rev. No

POR-C-E015-01

0

OJT ReportAUTO CAD ISO DRAWING

Doc. No Rev. Date Page

POR-C-E015-01 0 26 Nov. 2008 2 of 17

1.

Introduction 1.1. Subject ................ ......4 1.2. ....4 1.3. .................................................................................................................................... ............................4

2.

2.1. ISOMETRICS ...5 2.1.1. ISOMETRIC.. . ...5 2.1.2. ISO DWG. 6 2.1.3. piping ISO DWG. ..7 2.2. ISO DWG. AUTO CAD ...........................................................7

2.2.1. LIMITS ... .7 2.2.2. LAYER ... ..9 2.2.3. 12 2.3. ISO DWG. 15 2.3.1. LINE. 15 2.3.2. CIRCLE.. 16 2.3.3. ELBOW .

OJT ReportAUTO CAD ISO DRAWING

Doc. No Rev. Date Page

POR-C-E015-01 0 26 Nov. 2008 3 of 17

..17 2.3.4. GATE VALVE .. .18 3. ..21 ..21

4.

OJT ReportAUTO CAD ISO DRAWING

Doc. No Rev. Date Page

POR-C-E015-01 0 26 Nov. 2008 4 of 17

1.

1.1. . management . . communication management . . DRAWING , , . AUTO CAD ISO DRAWING . 1.2. 1.2.1. ISO 1.2.2. AUTO CAD ISO DRAWING 1.3. 1.3.1. ISO DWG. . 1.3.2. ISO DWG. AUTO CAD .. 1.3.3. AUTO CAD .

2.

2.1. ISOMETRIC 2.1.1. ISOMERIC

3.

ISOMETRICS are 2.5-dimensional drawings (= isometric to top coat).

As you can see, 60 to each side divided into intervals, as well as top and bottom of the vertical direction. This LINE indicates the chiseled geometry.

OJT ReportAUTO CAD ISO DRAWING

Doc. No Rev. Date Page

POR-C-E015-01 0 26 Nov. 2008 5 of 17

1In the above illustration is the "A" as the start point 1) plumbing goes to the North. 2) goes up. 3) to the East. 4) North. 5) down. 6) to the West. 7) to the North. "B" get to the point. This chiseled direction like plumbing. 3.1.1. ISO basics of DWG. (1) units, and scales Use unit (mm), plumbing, Lord of seven inch (B). As the scale is None-Scale. However, considering the whole Balance. (2) characters Mouth as the minimum size of the 3.0mm height. The type and size of the line ISO DWG. On line width standards

0.8mm

Nozzle Valve, Strainer Item NO. , , Symbol

0.2mm

0.2mm 0.2mm

2 (3)

Match Line Battery Line

A3 Standard Isometric .

3.1.1. Piping ISO DWG. Piping DWG. ISO DWG. .

OJT ReportAUTO CAD ISO DRAWING

Doc. No Rev. Date Page

POR-C-E015-01 0 26 Nov. 2008 6 of 17

.2. ISO DWG CAD for AUTO setting COMMEND window type specified in the command that you want to feature is available. Here, the full name for learning and "*" symbol and set down with shortcuts. " (Enterprise)" is the command prompt, type as the method of Enter key, numeric pad Enter key, the Space bar key, mouse right click four way.

3.2.1. the LIMITS set Output the drawings prior to written size drawings. The following two ways. (1) LIMITS LIMITS ) (Enterprise) I) specifies the upper-left corner or [on/off (OFF)]: 0.0 (Enterprise) Where the lower-left corner of the standards will caught a stinging. Most of the lower-left corner is 0, 0, get the value axis. It specifies the upper-right corner): 420, 297 (Enterprise) Enter the desired drawing size.(Size entered is A3size) * The drawing size rated dimension

( : mm)Drawing size and suffix

A0Draft Size

A1 841 X 594 20

A2 594 X 420 10

A3 420 X 297 10

A4 297 X 210 10

aXb C

1189 X 841 20

Outline gap

d

Do not iron When not

20

20

10

10

10

When the iron

25

25

25

25

25

OJT ReportAUTO CAD ISO DRAWING

Doc. No Rev. Date Page

POR-C-E015-01 0 26 Nov. 2008 7 of 17

La) Zoom (Enterprise), All (Enterprise) * Caution: after you set the Limits, the Zoom + All is done, I'd have given it. (2) MVSETUP: outskirts to draw LIMITS to setting with MVSETUP ) (Enterprise) I) drawings available space? [No (N)/Yes (Y)]: N (Enterprise) ) Unit type [Science (S)/decimal (D)/engineering/architecture (E) (A)/metric (M)]: M (Enterprise) La) input: 1 scale ratio (Enterprise) Enter the desired scale (Enterprise) 1: 1 1 (Enterprise) 1: 5 5 (Enterprise) Enter the paper width): 420 (Enterprise) Bar) enter the height of the paper: 297 (Enterprise)

A3 size paper outline is drawn as LIMITS are set.

3.1.2. LAYER settings Each line are the width, color, shape, not much has been its purpose. (1) the line color in AUTO CAD The thickness of the line, the General draft, as a separate purpose, whereas the AUTOCAD software 1 255 times the purpose of the line by up to color. 1-red: imaginary line, such as a centerline dimension line 2-yellow: thin 3 times-Green: tick 4 times-sky blue: very thick (2) the purpose of the category of the line

(3) LAYER settings LAYER ) (Enterprise) * shortcuts LA (Enterprise) Command and the following screen.

OJT ReportAUTO CAD ISO DRAWING

Doc. No Rev. Date Page

POR-C-E015-01 0 26 Nov. 2008 8 of 17

Add a layer I) Layer add tab to add a layer

Change line type) Line type to change the line type.

Because the load of the line types lack tab to add the line.

Change the stroke color).

OJT ReportAUTO CAD ISO DRAWING

Doc. No Rev. Date Page

POR-C-E015-01 0 26 Nov. 2008 9 of 17

Color changes the color line.

Line weights Line weight to weight.

3.2.2. switch to the isometric snap ISO order DWG. snap type and style to replace it with a isometric snap. (1) snap switch A) Shift + mouse click I) object snap settings Select (O) OSNAP (Enterprise), the transition is possible through the snap

OJT ReportAUTO CAD ISO DRAWING

Doc. No Rev. Date Page

POR-C-E015-01 0 26 Nov. 2008 10 of 17

), Select the snap and Grid tab

La) isometric

snap (M)

) Mouse cursor direction and DRAWING SHEET is

screen ISO changed as shown in.

: :

OJT ReportAUTO CAD ISO DRAWING

Doc. No Rev. Date Page

POR-C-E015-01 0 26 Nov. 2008 11 of 17

) Line [F5] . [Ctrl + E ]

OJT ReportAUTO CAD ISO DRAWING

Doc. No Rev. Date Page

POR-C-E015-01 0 26 Nov. 2008 12 of 17

[F5] [F5] : 30, 90 . : 90, 150 . : 30, 150 . 3.2. ISO DWG. ISO DWG. item .

3.2.1. LINE

LINE . ) LINE () L () .

OJT ReportAUTO CAD ISO DRAWING

Doc. No Rev. Date Page

POR-C-E015-01 0 26 Nov. 2008 13 of 17

LINE [F8] . ) [F5] . [Ctrl + E ] ) [F5] . [Ctrl + E ] ) [F5] . [Ctrl + E ] ) .

3.2.2. CIRCLE 1) 2) 3) 4) ELLIPSE () EL () [(A)/(C)/(I)] : I () . [(D)] : 300 () D () , .

OJT ReportAUTO CAD ISO DRAWING

Doc. No Rev. Date Page

POR-C-E015-01 0 26 Nov. 2008 14 of 17

3.2.3. ELBOW (1) 45 VE1 LINE . LINE .

) LINE () L () LINE ) [ (U)] : @60