Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
Bedienungsanleitung Instruction manual • Mode d’emploi
Manual de instrucciones • Руководство по эксплуатации
1
2
3
4
10
5
6
711
12
8
9
3
Inhaltsverzeichnis
Bezeichnung der Einzelteile
1 Spannschieber (Sicherungsschieber)2 Schlosshalter3 Schloss (Verschluss)4 Systemkasten5 Lauf6 Vorderschaft7 Kammergriff
8 Abzug9 Hinterschaft
10 Aufnahme für Blaser Sattelmontage11 Magazineinsatz12 Wechselmagazin
SeiteBezeichnung der Einzelteile 2 - 3 Allgemeine Sicherheitsregeln 4 - 5 1. Zusammenbauen, Zerlegen 62. Sicherungssystem und Kammergriffsperre 73. Laden der Waffe 84. Schussabgabe 8 - 95. Entladen 106. Verschluss aus- und einbauen 107. Laufwechsel 11 - 128. Wechsel der Verriegelungskammer 12 - 139. Abnehmen des Vorderschaftes/Vorderschaftwechsel/ 13
Vorderschaft Stutzen 14 - 1510. Offene Visierung (einstellbar) 1611. Zielfernrohrmontage 16 - 1712. Zielfernrohrmontage US Typ 1713. Kalibergruppen 1814. Koffer 1815. Abzugseinheit R8 .338 Lapua Magnum 1916. Pflege und Wartung 2017. Garantiebedingungen 21
deut
sch
4
Allgemeine Sicherheitsregeln
Ihre neue Blaser Repetierbüchse Modell R8 unterscheidet sich durch ihre be son de ren Konstruktionsmerkmale von anderen Repe tierbüchsen. Das erhöhte Sicherheitsangebot Ihrer Blaser Waffe darf Sie auf keinen Fall dazu verleiten, die erforderliche Sorgfalt und die ge setz lichen Bestimmungen im Umgang mit Waffen außer Acht zu lassen. Prüfen Sie als erstes, ob Sie die richtige Bedienungsanleitung haben: Die Mo dellbezeichnung R8 und die Kaliber angabe befinden sich auf der linken Laufseite hinten.
ACHTUNG:Vor Gebrauch der Waffe unbedingt diese Bedienungsanleitung ganz durchlesen. Die Waffe nur zusammen mit dieser Bedienungsanleitung weitergeben.
Bitte lassen Sie sich unterstützend zu dieser Bedienungsanleitung Ihre Waffe von Ihrem Fachhändler genau erklären und sich in ihren Gebrauch ein weisen.
Allgemeine Sicherheitsregeln für den Umgang mit Waffen• Stellen Sie sicher, dass Waffe und Muniton nie in
unbefugte Hände gelangen.• Bewahren Sie Waffe und Munition stets getrennt
voneinander auf, und zwar unter Verschluss, unerreichbar für Unbefugte
• Beachten Sie die gültigen gesetzlichen Bestimmungen für das Führen und Aufbewahren von Waffen und Munition.
• Machen Sie sich mit der Handhabung Ihrer Waffe gründlich vertraut und üben Sie vor dem Führen der Waffe alle Funktionen und Handgriffe mit ungeladener Waffe.
• Betrachten Sie jede Waffe als geladen und schussbereit, solange Sie sich nicht durch Öffnen des Verschlusses und Blick ins Patronenlager (Lauf) vom Gegenteil überzeugt haben. Auch eine ungeladene Waffe ist zu hand haben wie eine gela dene Waffe.
• Halten Sie die Mündung bei jeglicher Handhabung immer in eine Richtung, in der Sie weder Personen noch Sachen gefährden oder beschädigen können.
• Kontrollieren Sie vor dem Laden der Waffe, ob sich Ölrückstände oder sonstig Fremdkörper im Patronenlager oder Lauf befinden. Ölrückstände im Patronenlager oder im Lauf können zu deutlichen Treffpunktverlagerungen führen! Fremdkörper im Lauf (z.B. Wasser, Schnee, Erde) können Laufsprengungen verursachen und dadurch schwere Verletzungen des Schützen oder umstehender Personen herbeiführen! Stellen Sie sicher, dass auch während des Gebrauchs der Waffe keine Fremdkörper in den Lauf gelangen können!
• Verwenden Sie ausschließlich Munition, welche den Anforderungen der CIP, insbesondere hinsichtlich des maximalen Gebrauchsgasdruckes, Pmax, genügt. Jede Blaser Waffe ist vom Staatlichen Beschussamt entsprechend den Anforderungen des Beschussgesetzes und der Beschussverordnung mit einem Beschussgasdruck, welcher den zulässigen Maximalen Gebrauchsgasdruck Pmax um mindestens 25% übersteigt, geprüft. Übersteigen Gasdrücke der zu verwendenden Munition diesen Gasdruck, kann die Sicherheit des Anwenders oder Dritter
5
unter Umständen nicht gewährleistet werden. Dasselbe gilt für Patronenhülsen, welche ihrer Abdichtfunktion durch das sogenannte Lidern nicht oder nicht mehr gerecht werden.
• Laden Sie Ihre Waffe erst unmittelbar vor Gebrauch.
• Spannen (Entsichern) Sie Ihre Waffe erst unmittelbar vor dem Schuss. Beim Spannen (Entsichern) den Lauf in eine ungefährliche Richtung halten.
• Überprüfen Sie vor jedem Schuss das Vorder und Hintergelände.
• Richten Sie Ihre Waffe nur auf ein Ziel, das Sie eindeutig erkannt haben.
• Legen Sie den Finger nur an den Abzug, wenn Sie schießen wollen.
• Geben Sie nur dann einen Schuss ab, wenn ein sicherer Kugelfang gegeben ist.
• Versagt eine Patrone, dann öffnen Sie den Verschluss erst nach ca. 60 Sekunden. So vermeiden Sie die Gefahr durch einen Nachbrenner.
• Tragen Sie beim Schießen einen Gehörschutz.
Entladen Sie Ihre Waffe• vor dem Überqueren von Hinder nissen,• vor dem Besteigen und Verlassen von Hoch
sitzen,• vor dem Betreten eines Gebäudes,• vor dem Besteigen eines Fahrzeuges,• vor dem Betreten einer Ortschaft• und auch dann, wenn Sie die Waffe vor
übergehend ablegen oder aus händigen.
deut
sch
6
1. Zusammenbauen, Zerlegen
1.1. Zusammenbauen
• Lauf mit der Mündung nach oben in den Systemkasten einlegen und festhalten.
• Mittels mitgeliefertem InbusSchlüssel (SW5) die beiden Laufbefestigungs muttern handfest anziehen. Keine Verlängerung verwenden!
R8 mit Wechselmagazin:• Magazineinsatz von oben in das Wechsel
magazin einsetzen und nach unten drücken.• Das Wechselmagazin mit dem Magazin einsatz
von unten in das System drücken, bis beide Magazintasten jeweils mit einem deutlich hörbaren Klicken einrasten.
R8 ohne Wechselmagazin:• Magazineinsatz von oben in den Magazinschacht
einsetzen und nach unten drücken.• Verschluss mit den beiden Gleit schie nen enden
sorgfältig, parallel mit der Verschluss führung, hinten auf den Systemkasten setzen.
• Magazineinsatz nach unten drücken und Verschluss nach vorne in den Systemkasten schieben.
ACHTUNG: Das Wechselmagazin lässt sich nur in das System einsetzen, wenn die Magazin sicherung deaktiviert und das "S" im Boden des Wechselmagazins nicht zu sehen ist.
ACHTUNG:Der Kammergriff muss zum Einbau des Ver schlusses immer in hinterer Position arretiert sein, d. h. ca. im 45°Winkel. Befindet sich der Kammergriff in fast senkrechter Position, so lässt sich der Verschluss nicht einbauen. Kammergriff bis zum Einrasten in die 45°Position zurückschwenken.
ACHTUNG:Beim Zusammenbau grundsätzlich darauf achten, dass der Lauf, die Verriegelungskammer und der Magazineinsatz dem Kaliber ent sprechen.
1.2. Zerlegen
• Mit dem Daumen den Spannschieber (Sicherungsschieber) leicht nach vorne schieben (ca. 2 mm), gleichzeitig mit Zeige und Mittelfinger den Kammergriff nach hinten schwenken (entriegeln), dann den Verschluss gerade zurückziehen.
• Waffe entladen (siehe Abs. 5).• Schlossfang eindrücken und halten, gleichzeitig
mit der anderen Hand den Verschluss nach hinten herausziehen.
• Mittels mitgeliefertem InbusSchlüssel (SW5) die beiden Lauf befestigungs muttern lösen.
• Lauf herausnehmen.
7
2. Sicherungssystem und Kammergriffsperre
SicherungssystemDas Sicherungssystem der Blaser Repe tier büch se Modell R8 basiert auf der ent spann ten Schlagbolzenfeder: Mit dem Spannschieber (Siche rungs schieber) wird die Schlag bolzen feder erst kurz vor dem Schuss gespannt bzw. wieder entspannt, beim Repe tieren wird selbsttätig erneut gespannt.In entspannter (gesicherter) Stellung wird gleichzeitig der Kammergriff gegen un beabsichtigtes Öffnen des Verschlusses beim Führen der Waffe gesperrt, sofern dieser völlig geschlossen wurde.
2.1. Spannen (Entsichern)
• Spannschieber (Sicherungsschieber) mit dem Daumen bis zum Anschlag kräftig nach vorne schieben und Daumen nach oben abheben, dadurch rastet der Spannschieber (Sicherungsschieber) in der ent sicherten Stellung ein.
• Ein rotes Quadrat wird hinter dem Spannschieber (Siche rungs schieber) als Signal sichtbar. Die Waffe ist jetzt gespannt (entsichert).
2.2. Entspannen (Sichern)
• Zum Entspannen (Sichern) der Waffe den Spannschieber (Sicherungs schieber) mit dem Daumen nach vorne/unten drücken (entriegeln) und in seine Ausgangs stellung zurück gleiten lassen (das rote Signal Quadrat ist nicht mehr sichtbar).
ACHTUNG:Beim Spannen (Entsichern) und Entspannen (Sichern) auf keinen Fall in den Abzug greifen (wie bei Waffen mit außen liegendem Hahn). Dies würde den Schuss auslösen!
2.3. Kammergriffsperre
• Verhindert unbeabsichtigtes Verschluss öffnen. Sie tritt automatisch in Kraft, wenn die Waffe entspannt (gesichert) und völlig verriegelt ist.
2.4. Öffnen der entspannten (gesicherten) Waffe
• Mit dem Daumen den Spannschieber (Sicherungsschieber) leicht nach vorne schieben (ca. 2 mm).
• Gleichzeitig mit Zeige und Mittelfinger den Kammergriff nach hinten schwenken (entriegeln), dann den Verschluss gerade zurückziehen.
deut
sch
8
3. Laden der Waffe
3.1. Laden
• Spannschieber (Sicherungsschieber) zurücknehmen (entspannen/sichern).
• Verschluss öffnen (siehe Abs. 2.4).• Lauf und Patronenlager entölen und auf Fremd
körper kontrollieren.• Munition muss unbedingt mit dem Kaliber der
Waffe übereinstimmen.
R8 mit Wechselmagazin• Wechselmagazin entnehmen.• Patronen auf den Magazineinsatz des entnom
menen Wechselmagazins legen und kräftig nach unten durch die Magazinlippen drücken.
• Ge ladenes Wechselmagazin von unten in das System drücken, bis die beiden Magazintasten jeweils mit einem deutlich hörbaren Klicken einrasten.
R8 ohne Wechselmagazin• Patronen auf den Magazineinsatz legen und kräf
tig durch die Magazinlippen nach unten drücken.
Fassungsvermögen der Magazine:• Kalibergruppe "Mini" = 5 Patronen• Kalibergruppe "Standard" = 4 Patronen• Kalibergruppe "Medium" = 3 Patronen• Kalibergruppe "Magnum" = 3 Patronen• Kalibergruppe "Jeffery" = 2 Patronen• Kaliber 10,3 x 60R = Einzellader
PRÜFEN:Rotes Quadrat nicht sichtbar, Kammergriff ganz vorne. Die Waffe ist jetzt geladen, entspannt (gesichert) und gegen unbeabsichtigtes Öffnen gesperrt.
ACHTUNG: Wird bei geschlossenem Verschluss das Magazin aus der gespannten Waffe entnommen, gleitet der Spannschieber selbsttätig in die entspannte Position zurück. Die Schlagfeder wird dabei entspannt. Wird das Magazin bei geöffnetem Verschluss und gespannter Schlagfeder entnommen, bleibt der Spannschieber in gespannter Position, die Schlagfeder ist dabei gespannt.
3.2. Magazinsicherung
Jede Blaser Repetierbüchse R8 mit Wechsel magazin hat eine im Magazin integrierte Magazinsicherung, mit der die Magazin tasten gesperrt werden können.• Bei geöffnetem Verschluss den Verriegelungs
schieber im Wechselmagazin in die hintere Position bewegen = "S" sichtbar. Die Magazintasten sind gesperrt.
• Ist die Magazinsicherung aktiviert, lässt sich das Wechselmagzin nicht entnehmen, die Waffe kann aber wie eine R8 ohne Wechselmagazin geladen werden.
• Die Magazinsicherung kann bei geöffnetem Verschluss durch Verschieben des sich im Wechselmagazin be findlichen Schiebers jederzeit aktiviert und deaktiviert werden.
4. Schussabgabe4.1. Schießen und Repetieren
• Waffe durch Vorschieben des Spann schiebers (Sicherungsschiebers) spannen (entsichern).
• Ziel anvisieren und schießen.• Nachladen (repetieren): Den Verschluss am
Kammergriff bis zum Anschlag zurückziehen und wieder ganz nach vorne schieben.
HINWEIS:Wird der Kammergriff nicht völlig bis zum Anschlag vorgeschoben, kann die Patrone aus Sicherheitsgründen nicht zünden.
ACHTUNG:Solange sich der Spannschieber (Sicherungsschieber) in der vorgeschobenen, gespannten (entsicherten) Stellung befindet, spannt sich das Schloss der Waffe selbsttätig bei jedem Repetiervorgang. Wenn nicht weitergeschossen werden soll, ist durch Zurück lassen des Spannschiebers (Sicherungs schiebers) sofort zu entspannen (sichern).
9
ACHTUNG:Waffe immer erst unmittelbar vor Schuss abgabe spannen (entsichern). Wird kein Schuss abgegeben, Waffe sofort wieder entspannen (sichern). Wird ein Schuss ab gegeben und nach geladen (repetiert), Waffe sofort wieder entspannen (sichern), sofern kein weiterer Schuss beabsichtigt ist.
4.2. Optionaler Atzl Match-Jagd-Abzug
Der Atzl MatchJagdAbzug ermöglicht die Wahl zwischen einem niedrigen, sportlich orientierten Abzugsgewicht und einem höheren, jagdlich orientierten Abzugsgewicht. Die Wahl des Abzugsgewichtes erfolgt werkzeuglos anhand eines Umschalters am Magazinrahmen bei heraus genommenem Magazin (siehe Abb. 4.2.1). Neben dem Wechselmagazin mit Umschalter ist für die Funktion weiterhin eine spezielle Abzugseinheit im Systemkasten erforderlich (siehe Abb. 4.2.2). Der Umbau auf den Atzl MatchJagdAbzug darf ausnahmslos nur werkseitig (bei Blaser Jagdwaffen GmbH in Isny) erfolgen.
Wenn bei den Kalibern .375 Blaser Mag., .375 H&H Mag., .416 Rem. Mag. und .458 Lott die Gesamtlänge (maximale Patronenlänge L6) das Maß von 90,5 mm überschreitet, können diese Patronen nicht im Atzl MatchJagd Abzug verwendet werden
FunktionsweiseDurch Betätigen des Umschalters kann zwischen den beiden Abzugsgewichten gewählt werden:• Stellung "Match" : 250 g / 0.55 lbs• Stellung "Jagd" : 650 g / 1.43 lbs
HINWEIS:Das Atzl MatchJagdWechselmagazin kann ohne Einschränkung in einer R8 ohne Atzl MatchJagdAbzugseinheit verwendet werden. Dabei steht dann das spezifische Abzugsgewicht der eingebauten Abzugseinheit zur Verfügung, die Umschaltung ist außer Funktion. Die Verwendung eines Wechselmagazins ohne Umschaltung in einem System mit Atzl MatchJagdAbzugseinheit ist nicht möglich, das Wechselmagazin kann nicht im System einrasten.
ACHTUNG:Der Atzl MatchJagdAbzug reagiert aufgrund seines niedrigen Abzugsgewichtes bei der Einstellung "Match" besonders sensibel. Insbesondere das Zurückschnellen lassen des Abzugszüngels, nach einer Bewegung des Abzugszüngels entgegen der Abzugsrichtung, führt zu einer ungewollten Schussauslösung. Bei Kontakt des Abzugsfingers mit dem Abzugszüngel sowie allgemein bei der Handhabung der geladenen und gespannten Waffe ist deshalb besondere Sorgfalt notwendig!
ACHTUNG:Die Blaser Repetierbüchse Modell R8 ist mit einem Direktabzug ausgerüstet. Die Ein stellung kann und darf nur vom Werk verändert werden. Bei entladener und entspannter (gesicherter) Waffe regelmäßig den Abzug auf Gängigkeit überprüfen. Verharztes Öl und/oder Fremdkörper können die Abzugsfunktion beeinträchtigen und Funktionsstörungen verursachen.
Abb. 4.2.2.
Abb. 4.2.1.
f Umschaltung am Magazinrahmen
f Spezielle Abzugseinheit im Systemkasten
deut
sch
10
5. Entladen 6. Verschluss aus- und einbauen
5.1. Entladen
• Gespannte (entsicherte) Waffe durch Zurücklassen des Spannschiebers (Sicherungsschiebers) mit dem Daumen entspannen (sichern).
• Verschluss öffnen und zurückziehen (siehe Abs. 2.4.), gleichzeitig wird die Patrone aus dem Lauf herausgezogen und ausgeworfen.
R8 mit Wechselmagazin: • Wechselmagazin durch Eindrücken beider
Magazin tasten herausnehmen und die verbliebenen Patronen mit Zeige finger und Daumen nach vorne schieben, bis diese aus den Magazin lippen schnappen und dann entnehmen.
R8 ohne Wechselmagazin: • Im Magazineinsatz verbliebene Patronen mit
dem Daumen (oder mit dem Ver schluss) nach vorne schieben, bis diese aus den Magazin lippen schnappen und dann entnehmen.
• Prüfen, ob Lauf und Magazin leer sind.
6.1. Verschluss ausbauen
• Waffe entspannen und entladen.• Verschluss öffnen und ganz zurückziehen.• Dann Schlossfang eindrücken und halten, gleich
zeitig mit der anderen Hand den Verschluss nach hinten herausziehen.
Bei den Kalibern .222 Rem., .223 Rem., .22250, .243 Win., 6,5x55, 6,5x57, 7x57, 7,5x55, .308 Win. und 8x57 IS ist im Magazineinsatz ein beweglicher Kurz patronen schlossfang rechts außer halb der rechten Magazinlippe eingebaut. Zum Ausbauen des Verschlusses aus einer Waffe in einem der o. g. Kaliber:
• Rechte Magazinlippe nach innen drücken. Dadurch wird der Kurz patro nenschloss fang außer Funktion gesetzt.
• Verschluss bis zum regulären Schloss fang zurückziehen.
• Schlossfang eindrücken und halten, gleichzeitig mit der an deren Hand den Verschluss nach hinten herausziehen.
6.2. Verschluss einbauen
• Magazineinsatz im Systemkasten ganz nach unten drücken und halten.
• Verschluss mit den beiden Gleit schienen enden sorgfältig, parallel zur Verschlussführung, hinten auf den Systemkasten setzen.
• Nach vorne in den Systemkasten schieben.
11
7. Laufwechsel
Es gibt 6 Kalibergruppen (siehe Tabelle S.18). Bei Laufwechsel von einer Kaliber gruppe zur anderen muss die Verriege lungs kammer gewechselt werden, sodass sie zur Kalibergruppe des jeweils eingelegten Wechsellaufs passt. Die Zuord nung zum passenden Wech s ellauf geht aus der Tabelle auf Seite 18 hervor. Außerdem sind Verriegelungskammern und Läufe mit einem Kurzzeichen der Kalibergruppe gestempelt. Diese Mar kie run gen müssen nach dem Zusammenbau übereinstimmen.
Innerhalb der jeweils entsprechenden Kalibergruppe können die Läufe beliebig gewechselt werden, ohne Austausch der Verriegelungskammer.
Kalibergruppen:Mini Stempelung MIStandard Stempelung STMedium Stempelung MEMagnum Stempelung MAJeffery Stempelung JE10,3 x 60 R Stempelung CH
Grundsätzlich ist darauf zu achten, dass beim Laufwechsel auch der Magazineinsatz im entsprechenden Kaliber eingesetzt wird. Die Kaliberbezeichnungen sind seitlich auf dem Magazineinsatz vermerkt (siehe Abs. 7.2).
HINWEIS: Zum Lauf im Kaliber 10,3x60 R wird ein Einzel ladereinsatz mitgeliefert. Ein Magazin ist hier nicht erhältlich.
7.1. Wechsel des Laufes
• Waffe entspannen und entladen.• Verschluss ganz zurückziehen und ent nehmen.• Beide Laufbefestigungsschrauben mit Inbus
Schlüssel SW5 ganz lösen, diese verbleiben unverlierbar in ihren Führungen.
• Lauf aus dem Systemkasten heben.• Wechsellauf in sein Bett in den Systemkasten
einlegen.• Mittels InbusSchlüssel beide Lauf befesti
gungsschrauben handfest an ziehen.
R8 mit Wechselmagazin:• Den dem Kaliber des Wechsellaufs entspre
chenden Magazineinsatz von oben in das Wechselmagazin einsetzen. Das Wechselmagazin von unten in das System drücken, bis beide Magazintasten jeweils mit einem deutlich hörbaren Klicken einrasten.
R8 ohne Wechselmagazin: • Magazineinsatz herausnehmen (evtl. muss das
Zielfernrohr abgenommen werden, siehe Abs. 12.2).
• Den dem Kaliber des Wechsellaufs entsprechenden Magazineinsatz von oben in den Magazinschacht ein setzen.
• Prüfen, ob die auf der Verriegelungs kammer gestempelte Kalibergruppe ("MI", "ST", "ME", "MA", "JE", "CH", siehe Abs. 7 und Abb. 7.1.) zu der Kaliber gruppe des Wechsellaufs passt.
• Muss die Verriegelungskammer im Verschluss gewechselt werden, siehe Abs. 8.
HINWEIS:Stets auf ein sauberes Lauf bett achten! Ein Überschuss an Öl oder Waffen fett zwischen dem Lauf und dem System kasten hat negativen Einfluss auf die Präzision der Waffe.
deut
sch
12
8. Wechsel der Verriegelungskammer
7.2. Wechsel des Magazineinsatzes
R8 mit Wechselmagazin:• Verschluss öffnen.• Patrone aus dem Lauf entfernen.• Wechselmagazin entnehmen und ent laden.• Mit Mittel oder Zeigefinger im Magazineinsatz
unter die Zubringermulde greifen, dabei mit dem Daumen die linke Magazinlippe nach innen drücken und den Magazineinsatz nach oben herausnehmen.
• Den dem Kaliber des Laufes entsprechenden Magazineinsatz von oben in das Wechselmagazin einsetzen.
R8 ohne Wechselmagazin:• Waffe entspannen und entladen.• Verschluss ausbauen.• Magazineinsatz mit dem Zeigefinger entnehmen.• Den dem Kaliber des Laufes entsprechenden Ma
gazineinsatz von oben in den Magazinschacht einsetzen
8.1. Ausbau der Verriegelungs kammer
Diesen Vorgang am besten mit einem Fachhändler durchführen.• Waffe entspannen und entladen.• Verschluss öffnen und entnehmen.• Verschluss mit der Unterseite nach oben auf eine
flache Unterlage legen. • Mit einem festen Gegenstand den Kammerhalter
nach links drücken, nach oben heben und nach oben schwenken.
• Die Verriegelungskammer mit einer viertel Drehung gegen den Uhrzeigersinn drehen und nach vorne herausziehen.
8.2. Einbau der Verriegelungs kammer
• Kammerhalter im Verschlussgehäuse ganz hochklappen.
• Die einzusetzende Verriegelungskammer über den Schlagbolzen bis zum Anschlag in das Verschlussgehäuse schieben und mit einer viertel Drehung im Uhrzeigersinn zum Einhaken bringen (siehe Abb. 8.2).
• Die Verriegelungskammer soweit anhalten, bis sich der Kammerhalter in die Nut der Verriegelungskammer einschwenken lässt.
HINWEIS: Um das Einschwenken zu erleichtern, sollten Sie während des Vorgangs den Kammer stengel leicht vorund zurückbewegen.
• Kammerhalter wieder herunterklappen und gegen den Federdruck zum Einrasten bringen.
13
9. Abnehmen des Vorderschaftes/ Vorderschaftwechsel
Die Blaser Repetierbüchse R8 hat in den Varianten Semi Weight, Safari und Jagdmatch eine spezielle, breitere Ausfräsung im Vorderschaft. Beim Einlegen von Semi Weight, Safari oder Jagdmatchläufen in die R8 Normalausführung muss daher ein Vorderschaft der entsprechenden Ausführung verwendet werden.
9.1. Abnehmen des Vorderschaftes
• Bei herausgenommenen Lauf die Vorderschaftschraube mit InbusSchlüssel SW5 lösen und Vorderschaft nach vorne abziehen.
9.2. Aufsetzen des Vorderschaftes
• Vorderschaft von vorne auf das System aufsetzen und Vorderschaftschraube anziehen.
ACHTUNG:Ist der Kammerhalter nicht richtig einge rastet, tritt an der Schienenaußenseite ein Signalstift heraus. Der Verschluss lässt sich nur in den System kasten einsetzen, wenn der Signalstift nicht mehr hervorsteht und der Kammerhalter richtig eingerastet ist.
HINWEIS:Verriegelungskammern für Linksverschlüsse sind unter dem Kurz zeichen der Kalibergruppe mit einem "L" gestempelt.
ACHTUNG:Die Spreizhülse und die Stützhülse, welche die Verriegelungskammer umschließen, sind als wesentliche Teile des Verschlusses mittels eines vernieteten Stiftes gesichert. Es ist strengstens verboten, diesen Stift zu lösen! Die Entfernung der Spreizhülse und der Stützhülse führt beim Schuss zwangsläufig zur Aussprengung des Verschlusses und damit zu einer tödlichen Gefahr für den Schützen!
deut
sch
14
9.3. R8 Professional Success Stutzen
R8 Stutzen sind in zwei verschiedenen Lauflängen (52 cm und 58 cm) und zwei verschiedenen Laufprofilen (Standard 17 mm und Semi Weight 19 mm Laufdurchmesser an der Mündung) erhältlich.
Stutzen Vorderschaft Lauflänge / Laufprofil
Variante 1 520 mm / 17 mm
Variante 2 520 mm / 19 mm
Variante 3 580 mm / 17 mm
Variante 4 580 mm / 19 mm
9.4. Laufwechsel
Ausbau:• Waffe entspannen und entladen.• Verschluss ganz zurückziehen und entnehmen.• Beide Laufbefestigungsschrauben mit Inbus
Schlüssel (SW5) ganz lösen, diese bleiben unverlierbar in ihren Führungen.
• Lauf im Bereich des Patronenlagers an heben und nach vorne schieben (Abb. Nr. 9.2).
HINWEIS:In den StutzenVorderschaftabschluss eingesetzte Dauermagneten sorgen für eine konstante Anlage des StutzenVorderschaftabschlusses am Lauf. Das Entnehmen des Laufes gestaltet sich einfacher, wenn der Lauf im Bereich des Patronenlagers angehoben und dann nach vorne herausgeschoben wird.
Einbau:
PRÜFEN:StutzenVorderschäfte müssen dem Laufdurchmesser und der Lauflänge entsprechen.
• Wechsellauf in sein Bett in den System kasten einlegen (Abb. Nr. 9.3).
• Mittels InbusSchlüssel (SW5) beide Laufbe festigungsschrauben handfest an ziehen.
9.5. Umbau R8 Professional Success zu R8 Professional Success Stutzen
• Waffe entspannen und entladen.• Verschluss ganz zurückziehen und entnehmen.• Beide Laufbefestigungsschrauben mit Inbus
Schlüssel (SW5) ganz lösen, diese verbleiben unverlierbar in ihren Führungen.
• Lauf aus dem Systemkasten heben.• Beide VorderschaftabschlussBefestigungs
schrauben (Abb. Nr. 9.4) mittels InbusSchlüssel (SW5) lösen und mit Sicherungsscheiben herausnehmen.
HINWEIS: Auf Sicherungsscheiben achten (Abb. Nr. 9.4a).
• Vorderschaftabschluss nach unten abklappen und herausziehen.StutzenVorderschaft einführen und nach oben anklappen.
• Beide VorderschaftabschlussBefestigungsschrauben mit Sicherungsscheiben ein stecken und handfest anziehen (Abb. Nr. 9.5).
15
ACHTUNG:Dauermagnetische Felder sind in der Lage, Daten von MagnetDatenträgern, wie z.B. PCDisketten, PCFestplatten sowie auch Bankkarten und Kredit karten zu löschen und damit unbrauchbar zu machen. Daher sind Dauermagnete unbedingt von solchen Datenträgern fernzuhalten.
HINWEIS:Vom TÜV Süd wurden der R8 Stutzen mit Lauf und der R8 Stutzen ohne Lauf gemäß „Packing Instruction 953 for UN2807 Magnetized Material“ überprüft. Das Produkt ist nicht als UN2807 Magnetized Material eingestuft. Das Produkt darf mit Passagierflugzeugen und Frachtflugzeugen transportiert werden.
HINWEIS:Um eine Beeinträchtigung der Schuss leistung zu verhindern und eine einwandfreie Fun ktion zu gewährleisten, ist auf die Umsetzung folgender Punkte zu achten:• Der StutzenVorderschaft muss korrekt mit der
Schäftung verbunden und verschraubt sein.• Stets auf ein sauberes Laufbett achten!• Auf saubere die Auflageflächen im Stutzen
Vorderschaftabschluss achten! Ein Überschuss an Öl oder Waffenfett zwischen dem Lauf und dem Systemkasten hat negativen Einfluss auf die Präzision der Waffe.
ACHTUNG:Im StutzenVorderschaftabschluss befindet sich zwecks Vorderschaftsfixierung am Lauf ein Dauermagnet (Abb. Nr. 9.6). Das Magnetfeld des Dauermagneten kann die Funktion von kardialen Implantaten bzw. Herzschrittmachern stören. Der StutzenVorderschaftabschluss darf deshalb nicht in unmittelbare Nähe (5 cm oder weniger) eines kardialen Implantats oder Herzschrittmachers gebracht werden.
5 cm Mindestabstand vom StutzenVorderschaftabschluss !
deut
sch
16
11. Zielfernrohrmontage
Die Blaser Repetierbüchse Modell R8 ist vorbereitet für die Original Blaser Sattelmon tage (DBP). Wir gehen davon aus, dass Ihr Zielfernrohr auf dem ihm zugeordneten Lauf vom Fachhändler korrekt montiert wurde.
11.1. Zielfernrohr aufsetzen
• Deckel des hinteren und vorderen Halte elements aufklappen und beide mit dem Daumen ganz nach vorne/oben schwenken.
• ZF mit der rechten Hand am Mittelrohr über der Montage fassen, so dass der Daumen das vordere Halte element erreichen kann.
• Waffe mit der linken Hand am Vorder schaft fassen, Schaft auf dem Oberschenkel abstützen.
• ZFMontage mit den beiden runden Zapfen vorsichtig in die beiden ovalen Aus fräsungen auf der rechten Oberseite des Laufs setzen, nach links aufkippen und so festhalten.
• Erst das vordere und dann das hintere, aufgeklappte Halteelement mit dem Daumen nach hinten/unten drücken, bis es auf Anschlag (Spannung!) steht. (Ist dies zu leicht oder nur unter Kraftaufwand möglich, so ist die Montage falsch eingestellt. In diesem Fall durch einen Fachhändler nach Werksanweisung korrigieren lassen. Der ideale Druck zum Schließen der Halte elemente entspricht in etwa dem Druck des Sicherungsschiebers (Spannschiebers) der Waffe).
• Nun die beiden Deckel der Halte elemente schließen.
ACHTUNG:Auf saubere und fettfreie Auflageflächen achten!
10. Offene Visierung
10.1. Korn mit Höhenverstellung
• InbusSchlüssel SW1,3 von oben vor dem Korn in die Bohrung des Korn sattels einführen und die Inbusschraube entsprechend verdrehen:
• Korn (federunterstützt)herausdrehen = mehr Tiefschuss,hineindrehen = mehr Hochschuss.
10.2. Kimme (Visier) mit Seitenverstellung
• Das Kimmenblatt hat rechts und links Bohrungen für InbusSchlüssel SW1,3.
• Bei Linksschuss: Kimme nach rechts setzen, dabei linke Madenschraube lösen und rechte Madenschraube eindrehen.
• Bei Rechtsschuss: Kimme nach links setzen, dabei rechte Madenschraube lösen und linke Madenschraube eindrehen.
10.3. Safarivisierung mit Höhen- und Seitenverstellung
Seit 06/2014 ist auch die Blaser Safarivisierung verstellbar. Die Verstellung erfolgt mit einem Inbusschlüssel SW2 analog zu der der Offenen Visierung (siehe oben). Safarivisierungen älteren Datums sind nicht verstellbar, sondern werden mit einer Standard kornhöhe von 6 mm auf 30 m Fleck ab Werk eingeschossen. Andere Bauhöhen und Kimmen sind optional gegen Mehrpreis erhältlich.
17
11.2. Zielfernrohr abnehmen
• Waffe mit der linken Hand am Vorder schaft fassen und auf dem Ober schenkel abstützen.
• Beide Deckel der Halteelemente aufklappen.• Zuerst das hintere Element mit dem Daumen bis
zum Anschlag ganz nach vorne/oben schwenken.
• ZF mit der rechten Hand am Mittelrohr fassen und halten.
• Jetzt mit dem Daumen das vordere Halte element bis zum Anschlag nach vorne/oben schwenken.
• ZF nach rechts/oben abnehmen.
ACHTUNG: Bei zu geringem Abstand zwischen Auge und Zielfernrohr sowie bei nicht richtigem Sitz der Waffe an der Schulter, sind beim Schießen mit größeren Kalibern Verlet zungen nicht auszuschließen. Besonders bei starken Kalibern muss auf einen entsprechend großen Abstand zwischen Zielfernrohr und Auge sowie auf die richtige Schulteranlage geachtet werden.
12. Zielfernrohr montage US Typ
12.1. Zielfernrohr aufsetzen
• Beide seitlichen Inbusschrauben SW1/8" an der Montage um einige Umdrehungen nach links drehen.
• Zielfernrohr mit der rechten Hand am Mittelrohr über der Montage fassen.
• Waffe mit der linken Hand am Vorder schaft fassen, Schaft auf dem Ober schenkel abstützen.
• ZielfernrohrMontage mit den beiden runden Zapfen vorsichtig in die beiden ovalen Aus fräsungen auf der rechten Oberseite des Laufes setzen, nach links aufkippen und Zielfernrohr mit der linken Hand festhalten.
• Beide seitlichen Inbusschrauben an der Montage mit Inbusschlüssel SW1/8" handfest anziehen.
12.2. Zielfernrohr abnehmen
• Mit der linken Hand um Vorderschaft und Zielfernrohr fassen und Waffe auf dem Oberschenkel abstützen.
• Beide seitlichen Inbusschrauben an der Montage mit Inbusschlüssel SW1/8" um einige Umdrehungen lösen.
• Zielfernrohr abnehmen.
deut
sch
18
Mini "MI":
.222 Rem. .223 Rem.
.204 Ruger
Standard "ST":
.22250 7x64
.243 Win. .308 Win.
6XC .3006
6,5x55 SE 8x57 IS
6,5x57 8,5x63
6,5x65 RWS 9,3×57
.270 Win. 9,3x62
Medium "ME":6,5x68 8x68 S
7,5x55 Swiss
Magnum "MA":
.257 Weath. Mag. .300 WSM
.270 Weath. Mag. .338 Blaser Mag.
.270 WSM .338 Win. Mag.
7 mm Blaser Mag. .375 Blaser Mag.*
7 mm Rem. Mag. .375 H & H Mag.*
.300 Blaser Mag. .416 Rem. Mag.*
.300 Win. Mag. .458 Lott*
.300 Weath. Mag. .458 Win. Mag.
Jeffery "JE":
.500 Jeffery
Schweiz "CH":
10,3x60 R
* Kaliber in Kombination mit "Atzl MatchJagdAbzug" nicht möglich
14. Koffer
Im doppelschaligen, 3fach verschließ baren SpezialABS Transportkoffer ist die R8 nebst Zubehör auf Reisen richtig unter gebracht.
Waffenkoffer BFür Blaser Repetierbüchsen mit mon tiertem Vorderschaft. Lauf bis 70cm, Schaft bis 38cm Länge. Fächer für Ersatzmagazin, Zielfernrohr, Dokumente und Inbusschlüssel. Mit Zahlenschloss.LxBxH: 82x33x11cm
Waffenkoffer CFür Blaser Repetierbüchsen mit montiertem Vorderschaft. Lauf bis 70cm, Schaft bis 42cm Länge. Fächer für Wechsellauf, Ersatzverschluss und zweites Zielfernrohr, Dokumente und Inbusschlüssel. Mit Zahlenschloss. LxBxH: 84x45x11cm
13. Kalibergruppen
Bitte beachten, dass eine ständige Verfüg-barkeit aller oben aufgeführten Kaliber aus technischen Gründen nicht gewährleistet ist.
19
15. Abzugseinheit R8 .338 Lapua Magnum
AllgemeinesDie speziell angefertigte Abzugseinheit gewährleistet eine sichere Zuführung der Patronen auch bei maximaler Patronenlänge (max. L6 nach CIP) und erlaubt somit erstmals Auslandsjägern und Long Range Schützen das Schießen mit der R8 in dem begehrten Kaliber .338 Lapua Magnum.
FunktionsweiseDie neue Abzugseinheit kann in allen R8 Professional Success Schäftungen verwendet werden.
ACHTUNG:Kammer, Lauf und Abzugseinheit müssen dabei unbedingt alle dem Kaliber .338 Lapua Magnum entsprechen. Die Kennzeichnung befindet sich bei der Kammer am Zylinderkopf, auf dem Lauf am hinteren Ende bei der Seriennummer. Um Verwechslungen zu vermeiden wurde bei der Abzugseinheit .338 Lapua Magnum der optimierte Patronenpuffer orange eingefärbt und eingeklebt sowie die Abzugseinheit entsprechend beschriftet (siehe Abb. 1).
Technische Ausführungen
Abzugseinheit .338 LAPUAPatronenlänge: Bis zur maximalen von der CIP festgelegten PatronenlängeAbzugseinheit ATZL .338 LAPUAPatronenlänge: Abweichend von CIP Maximal länge: maximal bis 92,2 mm
Pflege und WartungDas Wechselmagazin und die Abzugseinheit müssen immer sauber und frei von Fremdkörpern gehalten werden.
» Optimierter Patronenpuffer, orange eingefärbt und eingeklebt
» Kaliberbezeichnung (nur .338 LAPUA Mag.)
deut
sch
20
16. Pflege und Wartung
Zur Waffenpflege sollten ausschließlich Mittel verwendet werden, die für diesen Zweck bestimmt sind.
Lauf:BlaserGewehrläufe werden aus hochwertigem Vergütungsstahl gefertigt, der höchsten Anforderungen hinsichtlich Reinheit, Homogenität und mechanischer Eigenschaften – insbesondere auch im hochdynamischen Bereich – gerecht wird.Die Materialqualität wird durch Werksprüfungen und ständige eigene Qualitätskontrollen überwacht und dokumentiert.
Lauf außen:Die Laufoberfläche außen ist plasmanitriert und brüniert, was eine hervorragende Kratzfestigkeit und – bei korrekter Pflege – sehr gute Korrosionsbeständigkeit gewährleistet, jedoch keinen 100%igen Korrosionsschutz.Wir empfehlen die Oberfläche sauber zu halten und regelmäßig mit geeignetem Waffenöl einen dünnen Schutzfilm aufzutragen. Insbesondere wenn der Lauf feucht wurde oder in einem Synthetikfutteral geschwitzt hat, ist dieser trocken zu wischen und – wie oben beschrieben – leicht einzuölen.
Lauf innen:Die Laufinnenoberfläche ist kaltgeschmiedet und hat eine sehr gute Oberflächenqualität. Die glatte Oberfläche verbessert den Korrosionsschutz, ersetzt jedoch keinesfalls eine sorgfältige Reinigung und Pflege. Wir empfehlen dringend, Patronenlager und Lauf vor Gebrauch der Waffe zu entölen und trockenzuwischen, um Treffpunktlage abweichungen zu vermeiden.Nach Gebrauch der Waffe ist der Lauf zu reinigen und zu konservieren, da durch Pulverrückstände im Patronenlager und im Lauf Feuchtigkeit angezogen wird. Dem Patronenlager gilt ein besonderes Augenmerk: Über die Patrone gelangt unter Umständen Handschweiß ins Patronenlager, der aggressiv wirken und zu Korrosion führen kann.Bei deutlichen Geschossablagerungen wird eine chemische Laufreinigung empfohlen. Nach erfolgter chemischer Reinigung sind Lauf und insbesondere das Patronenlager trocken zu wischen und leicht einzuölen.
ACHTUNG: Die Waffe keinesfalls mit abgeklebter Mündung oder mit angebrachtem Mündungsschoner lagern! Unbedingt die Anleitungen und Warn hin weise des Pflegemittelherstellers beachten!
Metallteile:Alle Metallteile der Waffe immer sauber und leicht geölt halten.Schaftöl eignet sich nicht zur Pflege von Metallteilen!
Wechselmagazin:Das Wechselmagazin sollte immer sauber und frei von Fremdkörpern gehalten werden!
Schäfte:Alle Holzschäfte von Blaser Jagdwaffen sind mit Ölschliff versehen. Wir empfehlen die regelmäßige Behandlung mit handelsüblichen Schaftpflegemitteln.Waffenöl eignet sich nicht zur Schaftpflege!
Pflegehinweise für Prof. Succ. mit Lede-reinlagen:Die Ledereinlagen der R8 Professional Succes haben eine Imprägnierung und müssen deshalb nicht regelmäßig gereinigt werden. Zur Pflege eignet sich die Blaser Lederpflege.
Optik:Siehe Pflegeanleitung des Optik herstellers. ACHTUNG:
Bei der Pflege von Jagdwaffen muss da rauf ge achtet werden, dass keine Öle oder Fette in das Abzugs und Schloss system gelangen. Un ter bestimmten Voraussetzungen können Öle und Fette verharzen (verhärten) und so mit gefähr liche Funktionsstörungen verursachen. Die Waffe vor jeder Jagd saison und vor jeder Jagdreise von einem Fach händ ler überprüfen lassen. Jede Waffe ist ein technisches Gerät mit regelmäßigem Kontroll bedarf.
21
17. Garantiebedingungen
die Mu nition auf Ihre Waffe abstimmen, indem Sie mehrere Munitionssorten prüfen. Die Munition gleichen Fabrikats und der gleichen Laborierung kann von Fertigung zu Fertigung und von Waffe zu Waffe eine un terschiedliche Schussleistung und Treffpunktlage haben.Bei optimal ausgewählter Munition, Zieloptik und Montage leisten wir Gewähr für eine hervor ragende Schussleistung unserer Waffen.Beanstandungen der Schuss leistung müssen innerhalb von 20 Tagen nach Verkaufsdatum schriftlich geltend gemacht werden. Wir behalten uns vor, die Waffe an ein unabhängiges Institut zur Überprüfung zu geben (DEVA oder Staatliches Beschussamt). Sollte dort eine hervorragende Schussleis tung bestätigt werden, sind wir berechtigt, die dafür ange fallenen Kosten beim Kunden einzufordern.
3. Umfang der Garantie
Garantieleistungen bewirken weder für die Waffe noch für die eingebauten Ersatzteile eine Ver längerung oder Erneuerung der Garantiefrist. Die Garantie frist für eingebaute Ersatzteile endet mit der Garantiefrist für die gesamte Waffe.
4. Garantieausschluss
Die Garantie wird ausgeschlossen bei:• Schäden als Folge normaler Abnutzung, bei
Nichtbeachtung der Betriebsanleitung oder unsachgemäßer Verwendung oder Handhabung und wenn die Waffe mechanische Beschädigungen, gleich welcher Art, aufweist.
• Schäden aufgrund höherer Gewalt oder Umwelteinflüsse.
• Reparaturen, Bearbeitungen oder Veränderungen der Waffe durch Dritte.
• Verwendung von wiedergeladener oder nicht CIPzugelassener Munition.
• Ausführung einer Brünierung durch Dritte.
Die Garantie besteht nicht für optische Zieleinrichtungen und Zielfernrohrmontagen anderer Hersteller als Blaser Jagdwaffen GmbH. Weitergehen de oder andere An sprüche, insbesondere solche auf Ersatz außerhalb der Waffe entstandener Schäden (Folgeschäden), sind – soweit eine Haftung nicht zwingend gesetzlich angeordnet ist – ausgeschlossen.
1. Herstellergarantie
Die Garantie der Blaser Jagdwaffen GmbH wird zusätzlich zu den gesetzlichen Gewähr leistungsansprüchen des Händlers geleistet, dies unter der Voraussetzung, dass der beiliegende Waffenpass innerhalb von zehn Tagen ab Verkaufsdatum bei Blaser Jagdwaffen GmbH vollständig ausgefüllt ein gegangen ist. Die Garantie wird nur für den Ersterwerber geleistet, der seinen Wohnsitz im Erwerbsland hat.
Die Garantie bezieht sich ausschließlich auf die Metall und Kunststoffteile der Waffe und auf Original Blaser Zielfernrohrmontagen, nicht aber auf die Ziel optik. Holzteile an der Waffe bedürfen einer besonderen Pflege und unterliegen als Natur pro dukt einer natürlichen Veränderung, die Garantie für Holzteile ist ausgeschlossen.
Die Garantiezeit beträgt zehn Jahre und beginnt mit dem Verkaufsdatum und umfasst alle Mängel und Schäden der Waffe (Metall und Kunststoff teile), die nachweislich auf Material oder Fertigungs fehlern beruhen. In diesem Rahmen übernimmt der Hersteller die Kosten für Material und Arbeitszeit. Für die Durchführung der Garantie arbeiten ist die Waffe an den autorisierten Fachhändler oder an die Produktionsfirma in Isny abzugeben.
Gefahr und Kosten für den Hin und Rück transport der Waffe trägt der Kunde. Die Garantieleistung erfolgt nach Wahl des Herstellers durch Reparatur oder Ersatz fehlerhafter Teile, ersetzte Teile gehen in das Eigentum des Herstellers über.
2. Garantie auf die Schussleistung
Die Schusspräzision einer Waffe ist von vielen Fakto ren abhängig. Der wichtigste Faktor ist die Munition. Nicht jeder Lauf schießt mit jeder Munitionssorte gleich gut, es können erhebliche Leis tungsunter schiede bestehen. Die Zieloptik und deren Montage ist ebenso bedeutend. Parallaxe, lose Absehen, Defekte der Absehen verstellung und eine mangelhafte Montage sind die häufigsten Ursachen für unbefriedi gende Schussleistungen. Deshalb sollten Sie vom Fachmann montierte MarkenZielfernrohre verwenden und
072015 Technische Änderungen vorbehalten
deut
sch
1
2
3
4
10
5
6
711
12
8
9
23
Table of Contents
Description of Parts
1 Cocking slide (safety slide)2 Bolt stop3 Bolt assembly4 Receiver5 Barrel6 Forearm7 Bolt handle
8 Trigger9 Buttstock
10 Seat for Blaser Saddle Mount11 Magazine insert12 Spare magazine
PageDescription of Parts 22-23 General Safety Rules 24 - 25 1. Assembly, Disassembly 262. Safety and Bolt Handle Lock 273. Loading the Rifle 284. Firing 28 - 295. Unloading 306. Removing and Installing Bolt Assembly 307. Exchanging Barrels 31 - 328. Exchanging the Bolt Head 32 - 339. Removing/Exchanging the forearm/ 33
Forearm Stutzen 34 - 3510. Open Sights 3611. Mounting the Scope 36 - 3712. Mounting the Scope US Type) 3713. Caliber Groups 3814. Rifle Cases 3815. R8 trigger unit .338 Lapua Magnum 3916. Care and Maintenance 4017. Warranty Conditions 41
engl
ish
24
General Safety Rules
Your new Blaser bolt action rifle model R8 is characterised by special design features, making it very different from other bolt action rifles. The enhanced safety features of your Blaser rifle should never induce you to ignore the necessary care and legal provisions with respect to handling arms. Please check first, whether you have the correct operating instructions: the model R8 and the caliber are indicated on the left side of the barrel, on its lower end.
CAUTION:Please read these operating instructions completely, before using the rifle. Only hand on the rifle together with the operating instructions.
Please ask your specialized dealer for an in-depth explanation of your rifle and instruc-tion in its use, as a supporting measure to these operating instructions
General safety rules for handling fire-arms• Ensure that firearm and ammunition never pass
into the hands of unauthorised persons.• Always keep firearm and ammunition separately,
in a secured unit and inacces sible to unauthorised persons.
• Observe applicable legal provisions for carrying and storing arms and ammunition
• Familiarise yourself thoroughly with the handling of your firearm and practise all functions and actions with the firearm un loaded, before starting to carry and use it
• Consider every firearm as loaded and ready to fire, unless you have convinced yourself of the contrary by opening the action and checking the chamber (barrel). Even when unloaded, a firearm has to be handled like a loaded firearm.
• During any handling, always hold the muz zle in a direction where you can neither je opardise nor damage persons or property.
• Before loading the firearm, always check, whether there are oil residues or other fo reign matter in the chamber or barrel. Oil residues in chamber or barrel may cause di stinct shifts in the point of impact! Foreign matter in the barrel (e.g. water, snow, soil) may cause a detonation of the barrel, leading to severe injuries of the shooter or persons in the vicinity! Ensure that no foreign matter can enter the barrel, also during use!
• Only use ammunition which meets the CIP requirements, in particular with regards to the maximum gas pressure Pmax according to CIP regulations.Every Blaser rifle is controlled and tested by the state proofhouse according to the requirements of the proofinglaw and regulations, using proof cartridges exceeding the maximal allowed gas pressure Pmax by a minimum of 25%. If gas pressures exceed prooflevel, the safety of the user and/ or third parties can no longer be guaranteed. The same applies to cartridge cases, where the sealfunction is no longer correct through obturation.
• Load your firearm only immediately before use.• Disengage from safe position (cock) your firearm
only immediately before shooting. Hold barrel into a direction out of danger during disengaging (cocking).
25
• Check the surrounding area, before every shot.• Point your firearm only at a target, which you
have clearly identified.• Only put your finger on the trigger, when you
want to shoot.• Only fire a shot, when a secure backstop exists.• When a cartridge fails, wait approx. 60 se conds
before opening the action, to avoid danger through hangfire.
• Wear ear protection during shooting.
Unload your firearm• before crossing obstacles,• before climbing and leaving raised hides,• before entering a building,• before climbing into a vehicle,• before entering a built area• and also, when you lay down or hand on the
firearm temporarily
engl
ish
26
1. Assembly, Disassembly
1.1. Assembly
• Insert barrel into receiver, with muzzle pointing upwards, and hold it there.
• Fasten the two barrel fastening nuts finger tight with the Allen key provided (SW5). Do not use extensions!
R8 with spare magazine:• Insert the magazine insert from above in the
spare magazine and press it down.• Insert the spare magazine with magazine insert
into the receiver from the bottom until both magazine buttons lock into position with audible clicks.
R8 without spare magazine:• Insert the magazine insert into the magazine
chamber from above and press it down.• Put the bolt assembly with the two guide rails
parallel onto the rear of the receiver.Press the magazine insert down and push the bolt assembly forward into the receiver.
CAUTION: The spare magazine can only be inserted in the bolt assembly, when the magazine safety is not activated and the "S" on the bottom of the spare magazine is not visible.
CAUTION:Until assembly, the bolt handle has to be in a rear position, that means in an angle of approx. 45°. When the bolt handle has an almost vertical position, the bolt handle can not be inserted. Pull the bolt handle until it latches in the 45° position.
CAUTION:When assembling the R8, please note, that the barrel, the bolt head and the magazine insert correspond to the correct caliber.
1.2. Disassembly
• Push safety slide (cocking slide) slightly for ward with your thumb (approx. 2 mm), at the same time, pull the bolt handle back wards with your index and middle finger (unlock), then pull bolt assembly back in a straight line.
• Unload rifle (refer to Para. 5).• Push in the bolt stop and hold it there, at the
same time, pull bolt assembly out towards the back, using your other hand.
• Loosen the two barrel fastening nuts with the Allen key provided (SW5).
• Remove barrel.
27
2. Safety and Bolt Handle Lock
Safety systemThe safety system of the Blaser bolt action rifle model R8 is based on an decocked firing pin spring: Thanks to the safety slide (cocking slide), the firing pin spring is cocked (engaged) immediately before the shot is fired. When repeating, the rifle is cocked again automatically. In its secured (decocked) position, the bolt handle is also blocked to prevent unintentional opening of the bolt assembly when moving the rifle, provided that the handle was fully closed.
2.1. Disengaging from safe position (cocking)
• Push safety slide (cocking slide) forward powerfully with your thumb, all the way to the stop, and lift thumb off. Doing so, the safety slide (cocking slide) locks into its cocked position.
• A red square becomes visible behind the safety slide (cocking slide) as a signal. The rifle is now disengaged from safe position (cocked).
2.2. Returning to the safe position (locking/decocking)
• To put the rifle on "safe", push the safety slide (cocking slide) forward/downward with your thumb (unlocking) and let it slide back into its starting position (the red signaling square is not visible anymore).
CAUTION:Under no circumstances should you put your fingers into the trigger when engaging (cocking) or disengaging (decocking) your rifle (you may be used to doing this on rifles with exposed hammers). This would trigger the shot, when the rifle is loaded!
2.3. Bolt handle lock
• Prevents unintentional opening of the bolt assembly. It becomes active automatically, when the rifle is put on "safe" (decocked) and fully locked.
2.4. Opening the locked (decocked) rifle
• Push the safety slide (cocking slide) slightly forward with your thumb (approx. 2 mm).
• At the same time, pull the bolt handle backwards with your index and middle finger (unlock), then pull bolt assembly back in a straight line.
engl
ish
28
3.Loading the Rifle
3.1. Loading
• Move safety slide (cocking slide) back (lock/decock).
• Open bolt assembly (refer to Para. 2.4).• Remove oil from barrel and chamber and check
for foreign matter.• Convince yourself under all circumstances that
the ammunition corresponds with the caliber of your rifle.
R8 with spare magazine• Remove spare magazine.• Patronen auf den Magazineinsatz des entnom
menen Wechselmagazins legen und kräftig nach unten durch die Magazinlippen drücken.
• Insert the loaded spare magazine into the receiver from below and ensure that both magazine buttons latch with an audible click.
R8 without spare magazine:• Put cartridges on the magazine insert and push
the magazine lips down strongly.
Magazine capacities• Caliber group "Mini" = 5 cartridges• Caliber group "Standard" = 4 cartridges• Caliber group "Medium" = 3 cartridges• Caliber group "Magnum" = 3 cartridges• Caliber group "Jeffery" = 2 cartridges• Caliber 10,3 x 60 R = single shot
PLEASE CHECK:Red square not visible, bolt handle in front position. The rifle is now loaded, put on "safe" (decocked) and locked against unintentional opening.
ATTENTION: If the magazine is removed from the cocked rifle with closed bolt assembly, the safety slide (cocking slide) will automatically decock into safe position. The main spring will also decock. If the magazine is removed when the bolt assembly is open and cocked, the safety slide (cocking slide) will remain cocked. The main spring will remain cocked, too.
3.2. Magazine safety
Every Blaser bolt action rifle R8 with spare magazine features a magazine safety which is integrated in the magazine locking the magazine buttons.• When the bolt assembly is open, push the locking
lever in the spare magazine all the way to the rear = "S" visible. The magazine buttons are locked.
• Once the magazine safety is activated, the spare magazine cannot be removed anymore, but the rifle can be loaded like a R8 not featuring a spare magazine.
• With opened bolt assembly, the magazine safety can always be activated or deactivated by pushing the lever in the spare magazine.
4. Firing4.1. Firing and Repaeting
• Cock the rifle by pushing the safety slide (cocking slide) forward.
• Aim at target and fire.• Reloading (repeating): Pull bolt assembly on the
bolt handle all the way back to the stop and then push all the way forward again.
Note:If the bolt handle is not pushed forward into the fully closed position, the cartridge will, for safety reasons, be unable to ignite.
CAUTION:As long as the safety slide (cocking slide) is in its forward, engaged (cocked) position, the bolt of the rifle will cock automatically with each repetition. When you do not want to continue shooting, lock (decock) immediately again by sliding the safety slide (cocking slide) backwards.
CAUTION:Only cock rifle immediately before firing, at all times. When no shot is fired, lock (decock) rifle again immediately.When a shot is fired and the rifle has been repeated, the rifle should be decocked again immediately, if the next shot is not required.
29
4.2. Optional Atzl Match-Hunt-Trigger
The Atzl MatchHuntTrigger provides the possibility of choosing between a light, competition orientated trigger pull and a heavier, hunting orientated trigger pull. Selecting the trigger pull is performed without use of tools by using the selector on the magazine frame with the magazine removed (refer to Pic. 4.2.1). Besides the exchangeable magazine with selector, a special trigger unit in the receiver is also required (refer to Pic. 4.2.2). The fitting of the Atzl MatchHuntTrigger may not under any circumstances be fitted by anybody else than Blaser Jagdwaffen GmbH in Isny.When using calibers .375 Blaser Mag., .375 H&H Mag., .416 Rem. Mag. and .458 Lott, the cartridges cannot be used in the Atzl MatchHuntTrigger, if the total length (maximum cartridge length L6) exceeds the length of 90.5 mm.
FunctionChoosing which trigger pull is achieved by moving the selector:• Postion "Match" : 250 g / 0.55 lbs• Position "Hunt" : 650 g / 1.43 lbs
NOTE:The Atzl MatchHuntTrigger exchangeable magazine can be used without limitations in an R8 without the Atzl MatchHunt Trigger unit. The trigger pull will correspond with the specific weight of the currently fitted trigger unit. The selector will have no function. The use of an exchangeable magazine without selector in a receiver with the Atzl MatchHuntTrigger is not possible, the exchangeable magazine will not engage.
CAUTION:The Atzl MatchHuntTrigger reacts sensitively when selected on "Match" because of the low trigger pull. If the trigger blade is pushed forward and quickly released, this could cause an accidental discharge. Precaution is required when the trigger finger contacts the trigger blade and general safety regulations should be strictly followed when using a loaded and cocked rifle.
CAUTION:The Blaser bolt action rifle model R8 is equipped with a direct pull trigger. Its setting can and may only be changed at the factory. Please check the trigger regularly for smooth movement, with the rifle unloaded and locked (decocked). Hardended oil and/or foreign matter may affect proper functioning of the trigger and cause malfunctions.
Pic. 4.2.2.
Pic. 4.2.1.
f Selector on trigger guard
f Special trigger unit in the receiver
engl
ish
30
5. Unloading 6. Removing/Installing Bolt Assembly
5.1. Unloading
• Lock (decock) the disengaged (cocked) rifle by sliding the safety slide (cocking slide) backwards with your thumb.
• Open bolt assembly and pull it back (refer to Para. 2.4), at the same time the cartridge is extracted out of the barrel and ejected.
R8 with spare magazine: • Remove the spare magazine by pushing in both
magazine buttons and remove the remaining cartridges by pushing them forward with the index finger and thumb, until they release out of the magazine lips.
R8 without spare magazine: • Push remaining cartridges in the magazine for
ward with your thumb (or the bolt assembly), until they release out of the magazine lips. Remove cartridges.
• Make sure that barrel and magazine are empty.
6.1. Removing the bolt assembly
• Decock and unload rifle.• Pull opened bolt assembly all the way back.• Now push bolt stop in and hold it in this position.
At the same time, pull bolt assembly out towards the back, with your other hand.
For the calibers .222 Rem., .223 Rem., .22250, .243 Win., 6,5x55, 6,5x57, 7x57, 7,5x55, .308 Win. and 8x57 IS, a movable bolt stop for short case cartridges is built into the magazine insert, on the right side, just outside the right magazine lip. In order to remove the bolt assembly of a rifle with one of the calibers mentioned above, please follow these steps:
• Push right magazine lip towards the middle of the receiver. This puts the bolt stop for short case cartridges out of function.
• Pull bolt assembly back until it reaches the regular bolt stop.
• Now push bolt stop in and hold it in this position. At the same time, pull bolt assembly out towards the back with your other hand.
6.2. Installing the bolt assembly
• Push magazine insert in the receiver all the way down and hold it in this position.
• Carefully put bolt assembly with the two rail ends onto rear end of receiver, parallel to bolt rail guide.
• Slide it forward into the receiver.
31
7. Exchanging Barrels
There are 6 caliber groups (refer to table on p. 32). When changing from one caliber group to another during a barrel exchange, the bolt head has to be changed as well, so that it corresponds to the caliber group of the interchangeable barrel actually mounted. Please refer to the table on page 32 for proper allocation of suitable interchangeable barrels. Furthermore, bolt heads and barrels are imprinted with a symbol for the respective caiber group. These markings have to compare after assembly is completed.
Within one caliber group, barrels may be interchanged at random, without having to exchange the bolt head.
Caliber groups:Mini stamp MIStandard stamp STMedium stamp MEMagnum stamp MAJeffery stamp JE10,3 x 60 R stamp CH
Make sure that the magazine insert of the corresponding caliber is installed, when performing a barrel exchange. The caliber denominations are marked on the side of the magazine insert (refer to Para. 7.2).
NOTE: With the barrel of the caliber 10,3x60R, a single shot insert is supplied. A magazine is not available.
7.1. Exchanging the barrel
• Decock and unload rifle.• Pull bolt assembly all the way back and remove it.• Loosen both barrel fastening nuts completely,
using Allen key (SW5). The nuts remain ceptive and cannot be lost.
• Lift barrel out of receiver.• Put exchange barrel into its channel inside re
ceiver.• Fasten the two barrel fastening nuts handtight
with the Allen key.
R8 with spare magazine:• Insert the magazine insert corresponding to the
caliber of the barrel from above into the spare magazine until both magazine buttons lock into position with audible clicks (refer to Para. 7.2.).
R8 without spare magazine: • Remove magazine insert (possibly, the scope has
to be removed for this, refer to Para.12.2).Insert the magazine insert corresponding to the caliber of the exchange barrel from above into the magazine well.
• Check, whether the caliber group marked on the bolt head ("MI", "ST", "ME", "MA", "JE", "CH", refer to Para. 7 and Fig. 7.1.) corresponds with the caliber group of the exchange barrel.
• If the bolt head in the receiver has to be exchanged: refer to Para. 8.
NOTE:Always ensure that the barrel channel is clean! Excessive oil or gun grease between barrel and receiver has a negative effect on the precision of the rifle.
engl
ish
32
8. Exchanging the Bolt Head
7.2. Exchanging the magazine insert
R8 with spare magazine:• Open bolt assembly.• Remove the cartridge from the barrel.• Remove the spare magazine and unload it.• Use your index finger or thumb to grip under the
follower tray in the magazine insert, press the left magazine lip to the inside and at the same time remove the magazine insert upwards.
• Insert the magazine insert corresponding to the caliber of the barrel from above into the spare magazine.
R8 without spare magazine:• Decock and unload rifle.• Remove bolt assembly.• Remove magazine insert with index finger.• Insert the magazine insert corresponding to the
caliber of the barrel from above into the receiver.
8.1. Removing the bolt head
You should best ask your specialized dealer for a demonstration of this pro-cess.• Decock and unload rifle.• Open bolt assembly and remove it.• Deposit bolt assembly on a flat surface, with the
under side pointing upwards.• Use a small screw driver or similar object to push
the retaining latch to the left, leverage it out and swivel it up.
• Rotate the bolt head anticlockwise by a quarter turn and pull it all the way to the front.
8.2. Installing bolt head
• Lift the retaining latch in the bolt assembly.• Now push the bolt head to be installed over the
firing pin until it touches the stop in the bolt housing and latch it clockwise by a quarter turn (refer to Para. 8.2).
• Stop rotating the bolt head when the retaining latch can be located in the groove of the bolt head.
NOTE: In order to ease installation move the opening lever backwards and forwards slightly.
• Tilt retaining latch down again and engage it against the pressure of the spring.
33
9. Removing the Forearm/Exchanging the Forearm
The Blaser bolt action rifle model R8 is, in the model versions Safari and Match, equipped with a special, wider forearm. When inserting a Safari or Match barrel into a regular version of the R8, the forearm has thus to be exchanged.
9.1. Removing forearm
• Remove barrel and loosen screw in forearm with Allen key (SW5). Pull forearm off towards the front.
9.2. Mounting the forearm
• Place forearm on receiver from the front and tighten screw in forearm.
CAUTION:If the retaining latch is not locked properly, a signalling pin emerges at the exterior side of the rail. The bolt assembly can only be inserted into the receiver, when the signalling pin has disappeared and the retaining latch has thus been locked properly.
NOTE:Bolt heads for lefthanded bolt assemblies are marked with an "L" underneath the symbol for the caliber group.
CAUTION:The expanding colletts and the supporting shell enclosing the bolt head, being an essential part of the bolt assembly, are secured with a rivet. It is strictly forbidden to loosen this rivet! Removal of the expanding colletts will, when a shot is fired, inevitably cause the bolt assembly to be ejected and thus lead to lethal danger for the shooter or bystanders!
engl
ish
34
9.3. R8 Professional Success Stutzen
All R8 Stutzen models are available in two barrel lengths (52 cm and 58 cm) and two different barrel contours (Standard with 17 mm and Semi Weight with 19 mm muzzle diameter).
Stutzen Forearm Version Barrel Length / Barrel Contour
Version 1 520 mm / 17 mm
Version 2 520 mm / 19 mm
Version 3 580 mm / 17 mm
Version 4 580 mm / 19 mm
9.4. Exchanging the barrel
Removing the barrel:• Uncock and unload rifle.• Pull bolt assembly all the way back and remove it.• Loosen both barrel fastening nuts completely
using Allen key (SW5). The nuts remain in their guide and cannot get lost.
• Lift barrel at the chamber area and push it forwards (refer to Pic. 9.2).
NOTE:Permanent magnets inserted in the Stutzen forearm end ensure a firm connection of Stutzen forearm end and barrel. Removing the barrel is easiest when the barrel is lifted out at the chamber area and pushed forward.
Inserting the barrel:
CHECK:Your Stutzen forearm has to match the barrel diameter and barrel length!
• Put exchange barrel into its channel inside receiver (refer to Pic. 9.3).
• Fasten the two barrel fastening nuts handtight with the Allen key (SW5).
9.5. Converting the R8 Professional Success into the R8 Professional
Success Stutzen
• Uncock and unload rifle.• Pull bolt assembly all the way back and remove it.• Loosen both barrel fastening nuts completely
using Allen key (SW5). The nuts remain in their guide and cannot get lost.
• Lift barrel out of receiver.• Loosen both screws in forearm end (refer to Pic.
9.4) with Allen key (SW5) and remove with safety washers.
NOTE: Mind the safety washers (refer to Pic. 9.4a).
• Fold down and pull off forearm end. Insert and attach Stutzen forearm.
• Insert both screws with safety washers in forearm end and fasten fingertight (refer to Pic. 9.5).
35
CAUTION:Permanent magnetic fields can also erase data from magnet storage mediums, e.g. computer discs, hard drives, bank cards and credit cards, making them useless. Therefore permanent magnets should not come into close contact with such storage mediums.
NOTE:The R8 Stutzen with barrel and the R8 Stutzen without barrel were examined by TÜV Süd according to “Packing Instructions 953 for UN2807 Magnetized Material”. The product is not classified as UN2807 Magnetized Material. The product may be transported by commercial and cargo aircraft.
NOTE:In order to avoid an impairment of shooting performance and ensure flawless function please pay careful attention to the following requirements:
• The Stutzen forearm must be connected and screwed together with the stock correctly.
• Always make sure that the barrel bedding is clean!
• Please make sure that the supporting surface in the Stutzen forearm end is clean! Residues of oil and gun grease between barrel and action have a negative effect on the rifles accuracy.
CAUTION:A permanent magnet is fitted in the Stutzen forearm tip to hold the forearm in position (refer to pic. 9.6). The magnetic field from the permanent magnet can disrupt the function of cardiac implants or pacemakers. The Stutzen forearm tip therefore should not come into close contact (5 cm or less) with a cardiac implant or pacemaker.
5 cm minimum distance away from the Stutzen forearm tip!
engl
ish
36
11. Mounting the Scope
The Blaser bolt action rifle model R8 is prepared for installation of the Original Blaser Saddle Mount (DBP). We assume that your scope has been mounted correctly by your specialized dealer on the barrel assigned to it.
11.1. Installing the scope
• Open lid of rear and front holding elements and swivel both to the front/up with your thumb.
• Hold scope with your right hand at the center tube, above the mount, so that you can reach the holding element at the front with your thumb.
• Hold rifle at the forearm with your left hand, support buttstock on your thigh.
• Insert the two round studs at the scope mount carefully into the two oval holes sunk into the upper right side of the barrel, tilt scope to the left onto the barrel and hold it in this position.
• Press the opened holding elements, first the one in front and then the one in the back, backwards/downwards with your thumb, until they reach their stop position (tension!). (If this is too easy or requires force, then the mount is maladjusted. Have your dealer correct this according to the factory instructions. The ideal pressure for closing the holding elements is roughly the same as the pressure required for the safety slide (cocking slide) of the rifle).
• Now close the two lids of the holding elements.
CAUTION:Please ensure that the engaging surfaces are clean and free from grease!
10. Open Sights
10.1. Frontsight with elevation adjust-ment
• Insert Allen key SW 1.3 into the bore of the frontsight from above, and turn Allen screw as needed: Frontsight (springsupported)Turning out = shooting deeper,Turning in = shooting higher.
10.2. Rear sight with lateral adjustment
• The rear sight blade has bores for Allen key SW 1.3 at the right and left side.
• When shooting to the left: set the blade to the right, loosen the left grub screw and tighten the right grub screw.
• When shooting to the right: set the blade to the left, loosen the right grub screw and tighten the left grub screw.
10.3. Safari sight with height and side adjustment
Since 06/2014 the Blaser Safari Sight is also adjustable. Adjustment is carried out using an Allen key SW 2 analog to the open sight (refer to above).Older safari sights are not adjustable, but are zeroed at the factory over 30 meters with a standard front sight height of 6 mm. Other heights and rear sights are available at extra cost.
37
11.2. Removing the scope
• Hold the rifle with your left hand at the forearm and support it on your thigh.
• Open both lids of the holding elements.• First swivel the rear holding element with your
thumb all the way to the front/up until it reaches the stop.
• Grip scope with your right hand at the center tube and hold it.
• Now swivel the holding element at the front with your thumb all the way to the front/ up until it reaches the stop.
• Remove scope, moving it to the right side and up.
CAUTION: If the distance between eye and scope (eye relief) is too short and if the rifle is not seated correctly at your shoulder, injuries are not to be excluded when shooting with big calibers. Especially in case of big calibers, care has to be taken that the distance between eye and scope (eye relief) is appropriate and that the rifle is seated correctly at the shoulder.
12. Mounting the Scope US-Type
12.1. Installing the scope
• Turn both lateral Allen screws SW 1/8" at the mount CCW several turns.
• Hold scope with your right hand at the centre tube above the mount.
• Hold rifle at the forearm with your left hand, support buttstock on your thigh.
• Insert the two round studs at the scope mount carefully into the two oval holes sunk into the upper right side of the barrel, tilt scope to the left onto the barrel and hold scope in this position with your left hand.
• Tighten both lateral Allen screws at themount fingertight with Allen key SW 1/8".
12.2. Removing the scope
• Grip around forearm and scope with your left hand and support rifle on your thigh.
• Loosen both lateral Allen screws at the mount with Allen key SW 1/8" several turns.
• Remove scope.
engl
ish
38
Mini "MI":
.222 Rem. .223 Rem.
.204 Ruger
Standard "ST":
.22250 7x64
.243 Win. .308 Win.
6XC .3006
6,5x55 SE 8x57 IS
6,5x57 8,5x63
6,5x65 RWS 9,3×57
.270 Win. 9,3x62
Medium "ME":6,5x68 8x68 S
7,5x55 Swiss
Magnum "MA":
.257 Weath. Mag. .300 WSM
.270 Weath. Mag. .338 Blaser Mag.
.270 WSM .338 Win. Mag.
7 mm Blaser Mag. .375 Blaser Mag.*
7 mm Rem. Mag. .375 H & H Mag.*
.300 Blaser Mag. .416 Rem. Mag.*
.300 Win. Mag. .458 Lott*
.300 Weath. Mag. .458 Win. Mag.
Jeffery "JE":
.500 Jeffery
Swiss "CH":
10,3x60 R
* Caliber in combination with "Atzl MatchHuntTrigger" not possible
14. Rifle Cases
In the doubleshell special ABS transportation case with three locks, the R8 is stored cor rectly when traveling.
Rifle case BFor Blaser bolt action rifle R8, with forearm and scope mounted. Also suitable for all single shot rifles. External dimensions LxWxH: 78x26x9 cm
Rifle case CFor all Blaser single shot rifles and Blaser bolt action rifle R8 with forearm mounted. Featuring additional compartments for second interchangeable barrel and scope. External dimensions LxWxH: 84x45x11 cm
13. Caliber Groups
Please note that permanent availability of all calibers listed above cannot be warranted for technical reasons.
39
15. R8 trigger unit .338 Lapua Magnum
GeneralThis specifically customized trigger unit ensures a reliable feeding of the cartridge, including those with maximum length (max. L6 according to CIP) and enables travelling hunters and long range shooters to shoot with this highly popular .338 Lapua Magnum caliber.
FunctionThe new trigger unit can be used in all R8 Professional Success stock and receiver units.
ATTENTIONBolt head, barrel and trigger unit must correspond to the caliber .338 Lapua Magnum. The marking can be found on the cylinder head of the bolt head and on the rear end of the barrel near the serial number. To avoid any possibility of confusion, the trigger unit .338 Lapua Magnum has an optimized bullet buffer which is orange in colour and glued in position. The trigger unit is also marked appropriately. (see picture)
Technical Remarks
Trigger unit .338 LAPUACartridge length: Up to the maximal cartridge length specified by CIPTrigger unit ATZL .338 LAPUAACartridge length: Differing from CIP maximum length: maximum to 92.2mm
Care and MaintenanceThe magazine insert and the trigger unit must always be kept clean and always remain free from foreign substances.
» Optimized bullet buff er, orange in colour and glued in position
» Caliber marking (only .338 LAPUA Mag.)
engl
ish
40
16. Care and Maintenance
Only use products for the care of your rifle, which are destined for this purpose.
Barrel:Blaser barrels are made using a high quality, quenched and tempered steel. The highest requirements are fulfilled in regard to purity, homogeneity and mechanical properties – particularly in the high dynamic sector. The materials quality is monitored and documented by various factory inspections and permanent quality control.
Barrel external:The barrel surface is externally plasma nitrated and blued, which is a excellent protection against scratching and with correct maintenance a high corrosion protection, not however a 100% corrosion protection.We recommend that the surface is kept clean and that a thin application of suitable gun oil is regularly applied. Especially, when the barrel is moist or has sweated inside a synthetic gun case. Here, the barrel should be wiped dry and as written above – lightly oiled.
Barrel internal:The internal surface of the barrel is cold forged and has a very good surface quality. The smooth surface improves the corrosion protection, does not however substitute proper care and maintenance. We strongly advise that the chamber and barrel are free of oil before use, so as to ensure there is no difference in the point of impact.After the barrel has been fired, the barrel should be cleaned and conserved, as the powder residues in the chamber and barrel will attract moisture. Special attention should be applied to the chamber: Hand sweat is transported into the chamber by the ammunition. This can react aggressively and cause corrosion.If ammunition residue (carbon/ copper fouling) can be seen, then we recommend that the barrel be chemically cleaned. After chemical cleaning, the barrel and in particular the chamber should be wiped dry and oiled.
CAUTION: The firearm should not be stored with a sealed muzzle or a muzzle protector!
Metal parts:Keep all metal parts of the rifle clean and slightly oiled at all times.Stock preservative is not suitable for polish-ing metal parts!
Spare magazine:Always keep the spare magazine clean and free of contaminants!
Stocks:All wooden stocks of Blaser hunting rifles are oil rubbed. We recommend to polish them regularly with standard stock care products.Gun oil is not suitable for stock care!
Care instructions R8 Professional Success with leather inserts:The leather inserts of the R8 Professional Success are standardly impregnated and don't need constant cleaning. We recommend the Blaser Leather for maintenance.
Optics:Please refer to care instructions of the optics manufacturer.
CAUTION:When oiling hunting rifles, care has to be taken that no oil or grease gets into the trigger and action system. Under certain conditions,oil and grease can resinify (harden), causing dangerous disruptions of functioning. Please have your rifle checked by your specialized dealer prior to each hunting season or hunting trip. Every rifle is a piece of technical equipment requiring regular checks.
41
17. Warranty Conditions
from one manufacturing run to the other and from one rifle to the other.When the optimum of ammunition, rifle scope and mount were selected, we provide a warranty for the excellent efficiency of our rifles.Complaints regarding gun efficiency have to be brought forward in writing within 20 days after the date of sale. We reserve the right to submit the rifle to an independent institution for verification (DEVA or Staatliches Beschussamt) [government proofhouse]. If excellent gun efficiency is confirmed there, we are entitled to claim the costs incurred for the tests from customer.
3. Scope of warranty
Work performed under warranty does not cause any prolongation or renewal of the warranty period for the rifle or built in spare parts. The warranty period for installed spare parts ends at the same time as the warranty period for the entire rifle.
4. Guarantee exclusion
The guarantee shall be excluded with:• Damage that is caused as the result of normal
wear and tear, with nonobservance of the ope rating instructions or improper use or handling and if the gun shows mechanical damages of any kind.
• Damages that are the result of force majeure or environmental influences.
• Repairs, treatment or changes to the gun performed by third parties.
• Use of reloaded or nonCIPpermitted ammunition.
• Blueing carried out by a third party.
The guarantee does not apply for optical sight equipment and telescopic sight mounts of manufacturers other than Blaser Jagdwaffen GmbH. More extensive or other claims, especially those that refer to compensation for damages that go beyond the gun itself (consequential damages) shall be excluded (provided liability is not legally ordered as compulsory).
1. Manufacturer’s warranty
Warranty of Blaser Jagdwaffen GmbH is provided in addition to statutory warranty claims by dealers, provided, that the enclosed firearms certificate is filled in completely and received by Blaser Jagdwaffen GmbH within ten days after the date of sale. Warranty is provided exclusively for the first purchaser having his residence in the country of purchase.
The warranty applies to the metal and plastic parts of the rifle only, including original Blaser riflescope mounts, but not the rifle scope. Wooden parts of the rifle require special care and, being natural products, are subject to natural changes. Warranty for wooden parts is excluded.
The warranty period amounts to ten years, starting with the date of sale. It includes any defects of and damages to the rifle (metal and plastic parts), which are proven to be due to faulty material or manufacturing. Within this framework, the manufacturer shall bear the costs for material and working time. For performance of work under this warranty, the rifle has to be returned to the specialized dealer or the production company in Isny.
Risk and costs of transportation of the rifle (outward and return) shall be borne by the customer. Warranty is performed in the discretion of manufacturer by repair or replacement of defective parts; replaced parts pass into manufacturer’s property.
2. Warranty for gun efficiency
The firing precision of a gun depends on a multitude of factors. The most important factor is the ammunition. Not every barrel fires equally well with every type of ammunition, there may be considerable differences in efficiency. The scope and its mount are of the same importance. Parallax, loose reticles, defects in reticle adjustment and faulty mounting are the most common causes for unsatisfactory gun efficiency. For these reasons, you should use branded scopes, mounted by a specialist, and you should tune in the ammunition to your rifle by testing several types of ammunition. Ammunition of the same make and charge may exhibit different efficiency and impact point characteristics
072015 Subject to technical changes.
engl
ish
1
2
3
4
10
5
6
711
12
8
9
43
Sommaire
Désignation des différentes pièces
1 Poussier d'armement (et de désarmement)2 Arrêtoir du verrou3 Verrou de culasse4 Boîtier de culasse5 Canon6 Devant7 Levier de culasse
8 Queue de détente9 Crosse
10 Encoches pour montage Blaser11 Support des munition12 Chargeur amovible
Page(s)Désignation des différentes pièces 42 - 43 Consignes générales de sécurité 44 - 45 1. Assemblage, démontage 462. Sécurité et verrouillage du levier de culasse 473. Chargement de l‘arme 484. Tir 48 - 495. Déchargement de l‘arme 506. Démontage et montage de la culasse 507. Remplacement du canon 51 - 528. Remplacement de la tête de culasse 52 - 539. Démontage et remplacement du devant/ 53
Devant Stutzen 54 - 5510. Visée ouverte 5611. Montage d‘une lunette de visée 56 - 5712. Montage d‘une lunette de visée type US 5713. Groupes de calibres 5814. Malette de transport 5815. Bloc de détente Blaser R8 .338 Lapua Magnum 5916. Nettoyage et entretien 6017. Conditions de garantie 61
fran
çais
44
Consignes générales de sécurité
Votre nouvelle carabine à verrou Blaser R8, se distingue des autres carabines par ses caractéristiques techniques particulières. Le niveau de sécurité remarquable que vous offre votre carabine Blaser, ne doit pas vous inciter à ne pas respecter les règles de sécurité élémentaires et réglementaires quant au maniement, à l‘entretien et au rangement de l‘arme. Veillez à ce que le mode d‘emploi qui est en votre possession corresponde bien au modèle R8 et au calibre de votre arme: ces deux éléments sont gravés sur le flanc gauche du canon.
ATTENTION:N‘utilisez cette arme qu‘après avoir lu en totalité son mode d‘emploi. Dans tous les cas, l‘arme ne doit jamais être cédée sans son mode d‘emploi.
En complément de ce mode d‘emploi, faites appel à votre armurier afin qu‘il vous explique le fonctionnement et le maniement de l‘arme.
Consignes générales de sécurité pour le maniement des armes• Assurezvous que l‘arme et les munitions ne se
retrouvent pas en possession de personnes non autorisées.
• Entreposez toujours votre arme et vos munitions séparément, sous clefs et inaccessibles aux personnes non autorisées.
• Respectez la législation en vigueur concernant le port et la détention d‘armes et de munitions.
• Avant toute utilisation, familiarisezvous au maniement et aux fonctionnalités de l‘arme, en veillant à ce qu‘elle ne soit pas chargée.
• Considérez toute arme comme chargée et prête à faire feu, aussi longtemps que vous ne vous êtes pas assuré(e) du contraire en ouvrant la culasse et en jetant un oeil dans le canon. Dans tous les cas, une arme déchargée doit être manipulée comme une arme chargée.
• Maintenez toujours la bouche du canon dans une direction où vous ne risquez ni de mettre en danger des personnes ou des biens, ni d‘endommager ces derniers.
• Avant de charger votre arme, vérifiez que la chambre et le canon ne contiennent ni traces d‘huile, ni corps étrangers. La présence d‘huile dans la chambre ou le canon, peut entraîner des écarts d‘impacts considérables! La présence de corps étrangers dans le canon (par ex. eau, neige, terre) peut entraîner l‘éclatement du canon et porter gravement atteinte au tireur ou aux personnes se trouvant à proximité! Assurezvous également que pendant l‘utilisation de l‘arme, aucun corps étranger ne puisse pénétrer dans le canon!
• N‘utilisez que des munitions qui répondent aux exigences de la CIP, notamment en ce qui concerne la pression de gaz maximale, Pmax. Jede Blaser Waffe ist vom Staatlichen Beschussamt entsprechend den Anforderungen des Beschussgesetzes und Chaque arme Blaser est contrôlée par le laboratoire allemand de balistique, conformément aux exigences réglementaires c‘est à dire entre autre avec une pression de gaz supérieure de 25% par rapport à la pression maximale du calibre de l‘arme. Un dépassement de la pression de gaz Pmax risque de mettre en danger le tireur et les personnes se trouvant à proximité immédiate.
45
Il en est de même si les douilles des munitions ne sont pas en mesure d‘assurer une étanchéité parfaite au niveau de la chambre.
• Ne chargez votre arme qu‘au dernier moment avant le tir.
• N‘armez votre arme qu‘au dernier moment, juste avant le tir. Cette opération doit être réalisée en prenant soin d‘orienter le canon dans une direction ne présentant aucun danger.
• Avant chaque tir, il convient de surveiller l‘amont et l‘aval de la cible.
• Ne tirez que sur une cible parfaitement identifiée.• Ne posez le doigt sur la queue de détente qu‘au
moment de vouloir tirer.• Prenez toujours soin de réaliser un tir fichant.• En l‘absence de mise à feu, n‘ouvrez la culasse
qu‘après env. 60 secondes. Vous éviterez ainsi tout risque lié à un retardement de mise à feu.
• Veillez à toujours porter une protection auditive lors du tir.
Déchargez votre arme• vant de franchir un obstacle,• avant de monter sur un poste d‘affût et avant
de le quitter,• avant de pénétrer dans un bâtiment,• avant de monter à bord d‘un véhicule,• avant d‘entrer dans une agglomération• et avant de ranger votre arme ou de la remettre
à une tierce personne, ne seraitce que pour un court instant.
fran
çais
46
1. Assemblage, démontage
1.1. Assemblage
• Insérez le canon, bouche vers le haut, dans le boîtier de culasse et maintenezle fermement.
• A l‘aide de la clef à six pans (type SW5), serrez manuellement les deux écrous de fixation du canon. N‘utilisez pas de rallonge!
R8 à chargeur amovible:• Insérez le support à munitions dans le chargeur
par la face supérieure et appliquez une pression du doigt vers le bas.
• Insérez l‘ensemble dans le boîtier de culasse par le bas, jusqu‘à ce que les deux clapets du chargeur soient bien en place avec un clic bien audible.
R8 à chargeur fixe:• Insérez le support de munitions dans le chargeur
par la face supérieure et appliquez une pression du doigt vers le bas.
• Placez l‘extrêmité antérieure des deux bras de la culasse soigneusement et parallèlement, sur l‘extrémité postérieure des deux rails de guidage.
• Appuyez sur le support de munitions et poussez la culasse en avant.
ATTENTION: Le chargeur amovible ne peut être mis en place dans le boîtier de culasse, qu‘à condition que sa sécurité soit désactivée et que le "S" situé sur le fond du chargeur ne soit plus visible.
ATTENTION:Pour le montage de la culasse, le levier de culasse doit toujours être incliné vers l‘arrière, càd respecter un angle d‘environ 45°. Si le levier de culasse est en position verticale, il est impossible de fermer la culasse. Faites bascuer le levier en arrière, jusqu‘à ce qu‘il atteigne un angle de 45°.
ATTENTION:Lors du montage, veillez attentivement à ce que le canon, la verrouillage de chambre et le chargeur correspondent bien au même calibre.
1.2. Démontage
• Poussez légèrement (env. 2 mm) le poussoir d‘armement et de désarmement vers l‘avant, tout en faisant pivoter le levier de culasse vers l‘arrière à l‘aide de l‘index et du majeur, puis tirez la culasse vers l‘arrière.
• Déchargez l‘arme (voir chap. 5).• Enfoncez l‘arrêtoir de la culasse et maintenez la
pression tout en tirant la culasse vers l‘arrière avec l‘autre main.
• Déserrez les deux écrous de fixation du canon, à l‘aide de la clef à six pans (type SW 5) livrée avec l‘arme.
• Retirez le canon.
47
2. Sécurité et verrouillage du levier de culasse
SécuritéLe système de sécurité de la carabine à verrou Blaser R8, est basé sur la mise hors tension du ressort agissant sur le percuteur: le bouton poussoir d‘armement et de désarme ment permet d‘activer le ressort au dernier moment avant le tir et de le désactiver si le tir n‘a pas lieu. Lors d‘une série de tirs, le ressort est activé automatiquement.Une fois que la sécurité est activée c‘est à dire que le tir n‘est pas possible, le levier de culasse est automatiquement bloqué s‘il est en position de fermeture. Ceci permet d‘éviter une ouverture inopinée de la culasse.
2.1. Armement
• Poussez fermement en avant le bouton poussoir à l‘aide du pouce, puis donnez une une impulsion verticale afin que le bouton s‘enclenche en position d‘armement.
• Un repère visuel rouge apparaît à l‘arrière du bouton poussoir. La carabine est désormais armée.
2.2. Désarmement
• Pour désarmer la carabine, exercez une pression vers l‘avant et vers le bas sur le bouton poussoir, puis accompagnez son retour en position initiale jusqu‘à ce que le point rouge ne soit plus visible.
ATTENTION:Lorsque vous manipulez le bouton poussoir d‘armement et de désarmement, ne manipulez en aucun cas la queue de détente (comme vous pouvez en avoir l‘habitude avec des armes à chien externe). Ceci déclencherait le départ du coup!
2.3. Verrouillage du levier de culasse
Il empêche l‘ouverture inopinée de la culasse. Il est automatiquement activé dès lors que la carabine est désarmée et que la culasse est en position fermée.
2.4. Ouverture de la culasse si la cara-bine est désarmée
• Appuyez légèrement avec le pouce sur le bouton poussoir (env. 2 mm).
• Pendant ce temps, tirez le levier de culasse en arrière à l‘aide de l‘index et du majeur.
fran
çais
48
3. Chargement de l‘arme
3.1. Chargement
• Placez le bouton poussoir de sécurité en position désarmée.
• Ouvrez la culasse (voir chap. 2.4).• Retirez les éventuels dépôts d‘huile dans le canon
et la chambre, vérifiez qu‘ils ne contiennent aucun corps étranger.
• Assurezvous impérativement que le calibre des munitions est bien identique à celui de l‘arme.
R8 à chargeur amovible• Retirez le chargeur amovible.• Placez les munitions sur le dessus du support à
munitions situé dans le chargeur et insérezles en appuyant fermement sur les munitions.
• Insérez le chargeur amovible dans le boîtier de culasse par le bas, jusqu‘à ce que les deux clapets soient dans leurs encoches respectives avec un clic bien audible.
R8 à chargeur fixe• Placez les munitions sur le dessus du support à
munitions et insérezles en appuyant fermement sur les munitions.
Capacité du chargeur:• Groupe de calibres "Mini" = 5 cartouches• Groupe de calibres "Standard" = 4 cartouches• Groupe de calibres "Medium" = 3 cartouches• Groupe de calibres "Magnum" = 3 cartouches• Groupe de calibres "Jeffery" = 2 cartouches• Groupe de calibres 10,3 x 60R = une cartouche
A VÉRIFIER:Point rouge invisible, levier de culasse fermé. L‘arme est chargée, armée et verrouillée.
ATTENTION: Si le chargeur est enlevé de la carabine armée lorsque la culasse est fermée, l’armeur se désarmera automatiquement sur une position de sécurité. Le ressort principal se désarmera également. Si le chargeur est enlevé lorsque la culasse est ouverte et armée, l’armeur restera armé. Le ressort principal restera également armé.
3.2. Sécurité du chargeur
Chaque carabine à verrou Blaser R8 à chargeur amovible, bénéficie d‘un chargeur à sécurité intégrée qui permet de verrouiller les clapets du chargeur.• Une fois que la culasse est ouverte, placez le ver
rouillage du chargeur en position arrière = "S" visible. Les clapets du chargeur sont bloqués.
• Une fois que le chargeur est verrouillé il est impossible de le retirer, mais la carabine peut être chargée comme une carabine R8 à chargeur fixe.
• Le verrouillage du chargeur peut être activé ou désactivé à tout moment, une fois que la culasse est ouverte.
4. Tir4.1. Tir et répétition de tir
• Armez la carabine en poussant le bouton poussoir en position d‘armement.
• Visée la cible et tirez.• Rechargement (répétition de tir): ramenez la cu
lasse jusqu‘à la butée arrière, puis poussezla à nouveau en position fermée.
REMARQUE:Pour des raisons de sécurité, si le levier de culasse ne revient pas complètement en position de fermeture le tir ne peut pas être déclenché.
ATTENTION:Aussi longtemps que le bouton poussoir se trouve en position d‘armement (point rouge visible), chaque fermeture de la culasse arme automatiquement la carabine. Si vous ne désirez plus tirer, placez immédiatement le bouton poussoir en position de désarmement (bouton rouge invisible).
ATTENTION:La carabine ne doit être armée qu‘au dernier moment avant le tir. Si le tir n‘a pas lieu, désarmez immédiatement votre carabine. En cas de tir suivi d‘un rechargement, désarmez également l‘arme si vous ne désirez plus tirer.
49
4.2. Détente Match Chasse Atzl en option
La détente Match Chasse Atzl offre la possibilité de choisir entre un poids de détente léger adapté au tir sportif et un poids de détente lourd plus adapté à la chasse. Le changement du poids de détente s’effectue sans aucun outil, seulement en utilisant le sélecteur sur le pontet avec chargeur retiré (voir pic. 4.2.1). A côté du chargeur interchangeable avec sélecteur, un bloc détente spécial dans le boîtier est également nécessaire (voir pic. 4.2.2). Le montage de la détente Match Chasse Atzl doit être impérativement et exclusivement fait par Blaser Jagdwaffen GmbH à Isny.
En utilisant les calibres .375 Blaser Mag., .375 H&H Mag., .416 Rem. Mag. and .458 Lott, la longueur totale (longueur maximale de la cartouche L6) excède la longueur de 90.5 mm, donc ces cartouches ne peuvent pas être utilisées dans la détente Match Chasse Atzl.
Fonction:Sélectionner le poids de détente voulu en changeant le sélecteur:• Position "Match" : 250 g / 0.55 lbs• Position "Jagd" : 650 g / 1.43 lbs
REMARQUE:Le chargeur interchangeable Match Chasse Atzl peut être utilisé dans une R8 sans le bloc détente Match Chasse Atzl et sans aucune restriction. Le poids de détente correspondra au poids spécifique du bloc détente installé. Le sélecteur n’aura aucune fonction. L’utilisation d’un chargeur interchangeable sans sélecteur dans un boîtier avec une détente Match Chasse Atzl n’est pas possible, le chargeur ne se montera pas.
ATTENTION:En position "Match", la détente Match Chasse Atzl est particulièrement sensible en raison de son poids de détente léger. Un départ de coup de feu involontaire est provoqué en particulier en faisant rebondir en arrière la queue de détente après avoir manœuvré la queue de détente en sens inverse du sens de tir. Il est par conséquent indispensable d’être particulièrement vigilent lors de la mise en contact du doigt de la gâchette avec la queue de détente et en général lors du maniement de fusils chargés et armés.
ATTENTION:La carabine Blaser R8 est équipée d‘une queue de détente directe. Son réglage peut et ne doit être modifié qu‘en usine. Contrôlez régulièrement son fonctionnement, mais uniquement avec une arme déchargée et désarmée. Un dépôt d‘huile et/ou un encrassement peuvent avoir une influence néfaste sur son bon fonctionnement.
Pic. 4.2.2.
Pic. 4.2.1.
f Sélecteur sur le pontet
f Bloc détente Match Chasse Atzl
fran
çais
50
5. Déchargement de l'arme
6. Démontage et mon-tage de la culasse
5.1. Déchargement
• Désarmez la carabine en ramenant le bouton poussoir en position initiale à l‘aide du pouce (la sécurité est alors activée).
• Ouvrez la culasse et tirezla en arrière (voir chap. 2.4.), ce qui provoque l‘éjection automatique de la munition.
R8 à chargeur amovible:• Retirez le chargeur amovible en appuyant si
multanément sur ses deux clapets, puis retirez chaque munition du chargeur en les faisant coulisser vers l‘avant à l‘aide de l‘index et du pouce.
R8 à chargeur fixe:• Retirez les munitions restées dans le support à
munitions à l‘aide du pouce (ou de la culasse), en les faisant coulisser vers l‘avant.
• Assurezvous que le canon et le chargeur soient vides.
6.1. Démontage de la culasse
• Désarmez et déchargez la carabine.• Ouvrez la culasse et tirez la complètement en
arrière.• Enfoncez l‘arrêtoir de la culasse et maintenezle
enfoncé, tandis que l‘autre main tire la culasse en arrière.
Pour les calibres .222 Rem., .223 Rem., .22250, .243 Win., 6,5x55, 6,5x57, 7x57, 7,5x55, .308 Win. et 8x57 IS un deuxième arrêtoir se trouve au niveau du support de munitions, à l‘extérieur du rebord droit. Pour le démontage de la culasse sur les armes correspondant à ces calibres, procédez ainsi:
• Appuyez sur le rebord droit du support à munitions pour désactiver l‘arrêtoir spécifique aux munitions courtes.
• Tirez la culasse en arrière jusqu‘à l‘arrêtoir standard.
• Enfoncez l‘arrêtoir standard et de l‘autre main, tirez la culasse en arrière jusqu‘à ce qu‘elle sorte du boîtier de culasse.
6.2. Montage de la culasse
• Enfoncez le support à munitions dans le boîtier de culasse et maintenezle dans cette position.
• Posez les deux branches de la culasse sur l‘arrière des rails du boîtier de culasse, en veillant à ce que les branches soient bien parallèles aux rails.
• Poussez la culasse vers l‘avant.
51
7. Remplacement du canon
Il existe 6 groupes de calibres (voir chap. 13). Si vous remplacez le canon par un canon destiné à un autre groupe de calibres, il est impératif de remplacer aussi la tête de culasse afin qu‘elle corresponde au groupe de calibre du nouveau canon. Les correspondances entre canon et tête de culasse sont indiquées dans le chap. 13. Par ailleurs, tête de culasse et canon sont estampillés selon le groupe de calibre auquel ils appartiennent. Ces marquages doivent toujours être identiques.
Au sein d‘un même groupe de calibres, les canons peuvent être changés sans pour autant changer la tête de culasse.
Groupes de calibres:Mini estampillage MIStandard estampillage STMedium estampillage MEMagnum estampillage MAJeffery estampillage JE10,3 x 60 R estampillage CH
Si vous changez de canon, veillez également à changer le support de munitions correspondant au calibre du canon. L‘indication du calibre se trouve sur le flanc du support de munition (voir chap. 7.2).
REMARQUE: Pour le calibre 10,3x60 R il n‘existe qu‘un support à munition monocoup. Ce calibre n‘est pas disponible avec un chargeur
7.1. Remplacement du canon
• Désarmez et déchargez la carabine.• Tirez la culasse en arrière jusqu‘au bout et re
tirezla.• Desserrez complètement les deux écrous fixant le
canon à l‘aide d‘une clé Allen (SW5). Les écrous restent dans leur guide et ne peuvent pas s‘en aller.
• Retirez le canon du boîtier de culasse.• Insérez le canon de remplacement dans le boîtier
de culasse.• Reserrez les deux écrous de fixation à la main
avec l‘aide de la clef à six pans.
R8 à chargeur amovible:• Insérez le support de munition correspondant au
calibre du canon dans le chargeur, puis placez le chargeur à son emplacement dans le boîtier de culasse, jusqu‘à ce que les deux verrous du chargeur soient bien en place avec un clic bien audible (voir chap. 7.2.).
R8 à chargeur fixe:• Retirez le support de munition (en démontant
éventuellement la lunette de tir, voir chap. 12.2.).• Insérez le support de munition correspondant au
calibre du canon de remplacement.• Vérifiez si l‘estampillage présent sur la tête de cu
lasse correspondant au groupe de calibre ("MI", "ST", "ME", "MA", "JE" "CH", voir chap. 7 et pic. 7.1.) est identique à l‘estampillage du canon de remplacement.
• Pour remplacer la tête de culasse, voir chap. 8.
REMARQUE:Veillez à toujours insérer le canon dans un logement propre! Un excès d‘huile ou de graisse pour arme entre le canon et le boîtier, nuit à la précision de l‘arme.
fran
çais
52
8. Remplacement de la tête de culasse
7.2. Remplacement du support de muni-tions
R8 à chargeur amovible:• Ouvrez la culasse.• Retirez la munition du canon.• Retirez le chargeur et videzle.• Appuyez sur la languette d‘approvisionnement
du support à munitions avec votre index ou votre majeur, appuyez sur le rebord gauche du support à munitions avec votre pouce, puis retirez le support par le haut.
• Remplacez le support à munitions par un support correspondant au calibre du canon, en l‘introduisant par le haut.
R8 à chargeur fixe:• Désarmez et déchargez la carabine.• Démontez la culasse.• Retirez le support à munitions en vous aidant
de l‘index.• Remplacez le support à munitions par un support
correspondant au calibre du canon, en l‘introduisant par le haut dans la cavité du magasin.
8.1. Démontage de la tête de culasse
Il est recommandé d‘assister à une démonstra-tion faite par votre armurier.• Désarmez et déchargez la carabine.• Ouvrez la culasse et démontezla.• Déposez la culasse sur une surface place, face
inférieure orientée vers le haut.• Poussez le verrou de la tête de culasse vers la
gauche en vous aidant d‘un outil rigide, faitesle coulisser vers le haut puis faitesle basculer.
• Appliquez une rotation d‘un quart de tour dans le sens inverse des aiguilles d‘une montre à la tête de culasse, puis retirezla en tirant vers l‘avant.
8.2. Montage de la tête de culasse
• Relevez complètement le verrou de la tête de culasse.
• Faites coulisser la tête de culasse jusqu‘à ce qu‘elle soit en place, puis appliquez une rotation d‘un quart de tour dans le sens des aiguilles d‘une montre afin de la mettre en butée, càd en position définitive de verrouillage (voir pic. 8.2).
• Veillez à maintenir la pression manuelle sur la tête de culasse, jusqu‘à ce que le verrou soit retourné en position de blocage sur la culasse.
REMARQUE:Pour faciliter l‘insertion, nous vous recommandons d‘effectuer de légers mouvements de va et vient sur l‘arrière de l‘écrou du percuteur.
• Rabaissez le verrouillage de la tête de culasse et encliquetezle par pression.
53
9. Démontage et rempla-cement du devant
La carabine à verrou Blaser R8 est équipée d‘un devant plus large sur les versions Semi Weight, Safari et Jagdmatch. Si vous optez pour un canon Semi Weight, Safari ou Jagdmatch il faudra veiller à monter un devant correspondant au type de canon choisi.
9.1. Démontage du devant
• Une fois le canon démonté, dévissez la vis de fixation du devant à l‘aide de la clef à six pans de type SW5 et retirez le devant en tirant vers l‘avant.
9.2. Montage du devant
• Posez le devant sur le boîtier de culasse, puis serrez la vis de fixation du devant.
ATTENTION:Si le verrouillage n‘est pas correctement en place, un repère visuel apparaît sur le flanc externe du rail. La culasse ne peut être insérée qu‘une fois ce repère supprimé.
REMARQUE:Les têtes de culasse destinées aux culasses des armes pour gauchers, sont marquées par un estampillage qui indique la lettre "L".
ATTENTION:Les douilles d‘écartement et de renfort qui se trouvent sur les contours de la tête de culasse et qui en constituent des pièces essentielles, sont maintenues par un rivet. Il est strictement interdit de supprimer ou de manipuler ce rivet! La suppression des douilles d‘écartement et de renfort aurait pour conséquence un déboitement subit de la culasse lors du tir, ce qui constituerait un danger de mort pour le tireur!
fran
çais
54
9.3. R8 Professional Success Stutzen
Tous les modèles R8 Stutzen sont disponibles en deux longueurs de canon (52 cm et 58 cm) et deux contours de canon différents (diamètre de bouche de 17 mm pour le standard et de 19 mm pour le Semi Weight).
Version du devant Stutzen Longuer du canon/contour du canon
Version 1 520 mm / 17 mm
Version 2 520 mm / 19 mm
Version 3 580 mm / 17 mm
Version 4 580 mm / 19 mm
9.4. Changement de canon
Retrait du canon:• Désarmez et déchargez la carabine.• Tirez la culasse en arrière jusqu‘au bout et reti
rezla.• Desserrez complètement les deux écrous fixant le
canon à l‘aide d‘une clé Allen (SW5). Les écrous restent dans leur guide et ne peuvent pas s‘en aller.
• Tirez le canon vers la chambre et poussezle en avant (voir pic. 9.2).
REMARQUE:Des aimants permanents insérés dans l‘extrémité du devant Stutzen garantissent un solide raccord entre l‘extrémité du devant Stutzen et le canon. Le retrait du canon est plus facile lorsque le canon est tiré hors de la chambre et poussé en avant.
Insertion du canon:
A VÉRIFIER:Assurez que votre devant Stutzen corresponde au diamètre et à la longueur du canon.
• Placez le canon de rechange dans son canal à l‘intérieur de la platine (voir pic. 9.3).
• Serrez à la main les deux écrous de fixation du canon à l‘aide de la clé Allen (SW5).
9.5. Conversion du R8 Professional Success en R8 Professional
Success Stutzen
• Désarmez et déchargez la carabine.• Tirez la culasse en arrière jusqu‘au bout et reti
rezla.• Desserrez complètement les deux écrous fixant le
canon à l‘aide d‘une clé Allen (SW5). Les écrous restent dans leur guide et ne peuvent pas s‘en aller.
• Retirez le canon de la platine.• Desserrez les deux vis à l‘extrémité du devant
(voir pic. 9.4) à l‘aide de la clé Allen (SW5) et retirezles avec les freins d‘écrou.
REMARQUE:N‘oubliez pas les freins d‘écrou (voir pic. 9.4a).
• Dépliez et retirez l‘extrémité du devant.• Insérez et attachez le devant Stutzen.• Insérez les deux vis avec des freins d‘écrou dans
l‘extrémité du devant et serrezles à la main (voir pic. 9.5).
55
ATTENTION:Les champs magnétiques permanents peuvent également effacer les données de supports de stockage magnétiques tels que des disquettes, des disques durs, des cartes bancaires et des cartes de crédit, les rendant inutilisables. Les aimants permanents ne doivent donc pas se trouver à proximité de tels supports de stockage.
REMARQUE:La R8 Stutzen avec canon et la R8 Stutzen sans canon ont été examinés par TÜV Süd suivant les «Instructions d‘emballage 953 pour le matériel magnétisé UN2807». Le produit n‘est pas classifié comme un matériel magnétisé UN2807. Le produit peut être transporté par l‘aviation commerciale ou l‘aviation de fret.
REMARQUE:Afin d‘éviter une détérioration de la capacité de tir et assurer un fonctionnement optimal, veuillez respecter les points suivants:• Le devant Stutzen doit être correctement raccor
dé et vissé à la crosse.• Assurezvous que le fût du canon est toujours
propre!• Assurezvous également que la surface d‘appui
à l‘extrémité du devant Stutzen est propre! Les résidus d‘huile et de graisse d‘arme entre le canon et le mécanisme ont un effet négatif sur la précision des carabines.
ATTENTION:Un aimant permanent est situé au bout du fût afin de maintenir le devant en position (voir pic. 9.6). Le champ magnétique de l‘aimant permanent peut perturber le fonctionnement de stimulateurs cardiaques ou de pacemakers. L‘extrémité du devant Stutzen ne doit donc pas se trouver à proximité (5 cm ou moins) d‘un stimulateur cardiaque ou d‘un pacemaker.
5 cm distance au moins d’extrémité du devant Stutzen !
fran
çais
56
11. Montage de lunette de visée
La carabine à verrou Blaser R8 est équipée en série des encoches permettant d‘accueillir le montage spécial Blaser (DBP). Nous partons du principe que votre armurier a procédé correctement au montage de votre lunette sur le support de montage.
11.1. Montage de lunette
• Relevez les couvercles des sabots de fixation avant et arrière, puis faitesles basculer complètement en avant à l‘aide du pouce.
• Saisissez la lunette au niveau du tube central avec votre main droite et positionnezla sur les encoches de fixation de façon à pouvoir atteindre le sabot de fixation avant avec votre pouce.
• Saisissez votre arme au niveau du devant avec votre main gauche, tout en appuyant la crosse sur votre cuisse.
• Placez les sabots de fixation dans les encoches ovales prévues à cet effet et situées sur le flanc droit du dessus du canon, basculez le tout vers la gauche et maintenez l‘ensemble en position.
• A l‘aide de votre pouce, faites tout d‘abord basculer le sabot de fixation avant vers l‘arrière puis vers le bas et répétez l‘opération avec le sabot de fixation arrière. Les deux sabots doivent être sous tension. (Si cette opération est trop facile ou trop difficile, le support de montage est mal réglé. Dans ce cas, faites procéder au réajustement du montage par votre armurier, conformément aux instructions de l‘usine. La pression idéale à exercer sur les sabots pour la fixation du montage, correspond à peu près à celle qu‘il faut exercer sur le levier d‘armement ou de désarmement de la carabine.
• Refermez les couvercles des sabots de fixation.
ATTENTION:Veillez à ce que les encoches de fixation soient propres et exemptes de graisse!
10. Visée ouverte
10.1. Guidon réglable en hauteur
• Insérez la clef à six pans de type SW1,3 par le dessus dans le taraudage du guidon, puis tournez la clef à six pans selon vos désirs:
• Guidon (monté sur ressort)augmentation de la hauteur = tir plus bas,diminution de la hauteur = tir plus haut.
10.2. Hausse à réglage latéral
• La lamelle de hausse est munie de part et d‘autre d‘un taraudage pour clef à six pans de type SW1,3.
• Déviation de tir à gauche:Placer la hausse à droite, en déserrant la vis gauche et en serrant la vis droite.Déviation de tir à droite:Placer la hausse à gauche, en déserrant la vis droite et en serrant la vis gauche.
10.3. Visée Safari avec réglage vertical et
horizontal
A partir de Juin 2014, la visée Blaser Safari est également réglable. Ce réglage s’obtient à l’aide d’une clé Allen SW2 analogue à celle de la visée standard (voir cidessus).Les visées Safari plus anciennes ne sont pas réglables mais réglées départ usine pour une visée plein centre à 30 m. D'autres hauteurs de construction et d’autres visées sont disponibles en option contre supplément.
57
11.2. Démontage de lunette
• Saisissez l’arme au niveau du devant avec votre main gauche et appuyez l’arme sur votre cuisse.
• Ouvrez les deux clapets des tenons de verrouillage.
• Avec votre pouce, basculez d’abord le tenon arrière vers l’avant par une rotation, jusqu’à ce qu’il soit en butée.
• Saisissez la lunette au niveau du tube central avec votre main droite et maintenezla en position.
• Avec votre pouce, basculez ensuite le tenon avant vers l’avant par une rotation, jusqu’à ce qu’il soit en butée.
• Faites basculer la lunette de visée vers la droite et le haut, puis retirezla.
ATTENTION:Si l’écart entre la lunette de visée et votre oeil est insuffisant ou si l’arme est mal épaulée, le tir de gros calibres peut entrainer des blessures.Pour le tir de gros calibres, il est particulièrement recommandé de veiller à maintenir un écart conséquent entre votre œil et la lunette, ainsi que d’épauler l’arme avec le plus grand soin.
12. Montage de lunette de visée type US
12.1. Montage de la lunette
• Deserrez (en tournant vers la gauche) de quelques tours de clef à six pans de type SW1/8", les deux vis qui se trouvent sur le montage.
• Saisissez le tube central de la lunette avec votre main droite et placez la lunette audessus du montage.
• Tenez votre arme avec la main gauche au niveau du devant et posez la crosse sur votre cuisse.
• Posez les deux sabots de fixation dans les encoches ovales situées sur le flanc droit du dessus du canon, basculez l‘ensemble vers la gauche tout en le maintenant avec la main gauche.
• Reserrez manuellement les deux vis latérales du montage, à l‘aide d‘une clef à six pans de type SW1/8".
12.2. Démontage de la lunette
• Saisissez le devant de l‘arme et la lunette avec votre main gauche, puis appuyez la crosse sur votre cuisse.
• Deserrez les deux vis latérales du montage, en procédant à quelques rotations à l‘aide d‘une clef à six pans de type SW1/8".
• Retirez la lunette.
fran
çais
58
Mini "MI":
.222 Rem. .223 Rem.
.204 Ruger
Standard "ST":
.22250 7x64
.243 Win. .308 Win.
6XC .3006
6,5x55 SE 8x57 IS
6,5x57 8,5x63
6,5x65 RWS 9,3×57
.270 Win. 9,3x62
Medium "ME":6,5x68 8x68 S
7,5x55 Swiss
Magnum "MA":
.257 Weath. Mag. .300 WSM
.270 Weath. Mag. .338 Blaser Mag.
.270 WSM .338 Win. Mag.
7 mm Blaser Mag. .375 Blaser Mag.*
7 mm Rem. Mag. .375 H & H Mag.*
.300 Blaser Mag. .416 Rem. Mag.*
.300 Win. Mag. .458 Lott*
.300 Weath. Mag. .458 Win. Mag.
Jeffery "JE":
.500 Jeffery
Suisse "CH":
10,3x60 R
* Ce calibre ne peut pas être combiné avec la détente Match Chasse Atzl
14. Malette de transport
La malette de transport double coque en ABS spécial à triple verrouillage protège parfaitement votre carabine R8 et ses accessoires.
Coffret pour armes BPour carabine à verrou Blaser R8 avec devant monté et lunette de visée. Convient également aux armes à canon basculant.Dimensions externes LxLxH: 78x26x9 cm
Coffret pour armes CPour toutes les armes Blaser à canon basculant, ainsi que pour la carabine à verrou R8 avec devant monté. Compartiments supplémentaires pour deuxième canon et deuxième lunette de visée. Dimensions externes LoxLaxH: 84x45x11 cm
13. Groupes de calibres
Veuillez prendre en compte que pour des rai-sons d‘ordre technique la disponibilité de tous les calibres énumérés, ci-dessus, ne peut pas être garantie en permanence.
59
15. Bloc de détente Blaser R8 .338 Lapua Magnum
GeneralitiesCe bloc de détente est spécialement conçu pour garantir une alimentation parfaite des cartouches, également pour des munitions dont la longueur (L6 d’après la norme CIP) est maximale. Il permet ainsi à tous les chasseurs à l’étranger ainsi qu’aux tireurs longue distance d’utiliser le très apprécié calibre .338 Lapua Magnum.
FonctionaliteCe nouveau bloc de détente peut être utilisé dans toutes les crosses Professional Success
ATTENTIONLa tête de culasse, le canon et le bloc de détente doivent impérativement être coordonnés au calibre .338 Lapua Magnum. Les marquages se trouvent sur la tête de culasse, sur le canon, à l’arrière, près du N° de série. Afin d’éviter les confusions avec les blocs de détente usuels, nous avons placé et collé un tampon amortisseur orange dans le boîtier de magasin et effectué un marquage spécifique sur le bloc de détente (voir ill.)
Specifications Techniques
Bloc de détente .338 LapuaLongueur de cartouche: Longueur maximum indiqué par la norme CIPBloc de détente ATZL .338 LapuaLongueur de cartouche: Différent de la longueur maximale indiqué par la norme CIP: Longueur maximale 92,2 mm
EntretienLe magasin et le bloc de détente doivent toujours être tenus propres et libres de tous corps étrangers.
» Tampon amortisseur optimisé, de couleur orange, collé
» Description du calibre (seulement .338 Lapua Mag.)
fran
çais
60
16. Nettoyage et entretien
L‘entretien des armes ne doit être fait qu‘avec des produits et ustensiles prévus à cet effet.
Canon:Les canons des armes Blaser sont réalisés en acier traité à chaud et leurs caractéristiques répondent aux meilleures normes de pureté, d’homogénéité et de mécanique – leur conférant ainsi une souplesse à toute épreuve.La qualité des produits est assurée par des contrôles internes permanents, aussi bien au niveau des sites de production que pour chaque étape de la production.
Surface externe du canon:La surface externe du canon est nitrurée au plasma et bronzée, ce qui lui assure une excellente résistance aux égratignures ainsi que – moyennant un entretien ad hoc – une très bonne résistance à la corrosion,celleci ne pouvant être garantie à 100%.Nous recommandons de maintenir cette surface propre, ainsi que d‘appliquer régulière un léger film de lubrifiant pour armes. Si le canon a été en contact avec l’humidité ou stocké dans un étui synthétique, l’idéal consiste à le sécher soigneusement avant d’appliquer le film de lubrifiant évoqué, cidessus.
Surface interne du canon:La surface interne du canon est martelée à froid, ce qui lui confère une qualité hors du commun. Son aspect lisse améliore la résistance à la corrosion, mais ne remplace en aucun cas un nettoyage et un entretien minutieux. Nous vous recommandons instamment de retirer le film de lubrifiant appliqué dans la chambre et l’âme du canon avant d’effectuer des tirs, ceci afin de conserver une précision absolue.Après utilisation il convient de nettoyer l’âme du canon et de la protéger, car les dépôts de résidus de poudre qui se trouvent dans la chambre et le canon sont hydrophiles. La chambre mérite une attention particulière : des traces de sueur peuvent être déposées dans la chambre par le biais de la douille, cette sueur étant particulièrement corrosive.En cas de dépôts importants de résidus de poudre, il est recommandé de réaliser un nettoyage chimique de l’âme du canon. Une fois ce nettoyage réalisé il convient de bien sécher le canon mais aussi et
surtout la chambre, avant d’appliquer un film de lubrifiant protecteur.
ATTENTION: L’arme ne doit en aucun cas être stockée avec la bouche du canon obstruée par un papier adhésif ou par une protection de bouche! Respectez impérativement les consignes et mises en garde précisées dans le mode d‘emploi du produit utilisé!
Pièces métalliques:Veillez à toujours maintenir une légère couche d‘huile sur toutes les pièces métalliques facilement accessibles et nettoyées au préalable.Les huiles pour crosses ne sont pas adaptées à l‘entretien des pièces métalliques!
Chargeur amovible:Le chargeur amovible doit toujours être parfaitement propre et indemne de corps étrangers!
Crosse et devant:Toutes les crosses et tous les devants en bois des armes Blaser, sont poncées huilées. Nous vous recommandons un entretien régulier à l‘aide de produits spécifiques disponibles dans le commerce.Les huiles pour armes ne sont pas adaptées à l‘entretien des crosses et devants en bois!
Conseils d'entretien Professional Success avec inserts en cuir:Les inserts en cuir du R8 Professional Success sont imprégnés. Nettoyage en permanence n'est par neccessaire. Pour le soins, nous recommandons le Blaser soins pour cuir.
Optique:Reportezvous à la notice d‘entretien du fabricant d‘optique.
ATTENTION:Pour l‘entretien des armes de chasse, il est impératif de veiller à ce qu‘il n‘y ait aucun reliquat d‘huile ou de graisse dans le mé-canisme de détente et la culasse. Sous certaines conditions, ces reliquats peuvent se rigidifier et provoquer des dysfonctionne-ments potentiellement dangereux. Avant l‘ouverture de la chasse et avant un voyage de chasse, il est recommandé de faire réviser votre arme par un armurier. Chaque arme est un objet technique méritant un contrôle régulier.
61
17. Conditions de garantie
nition pour lequel votre canon délivre la meilleure précision, ceci en essayant plusieurs types de munition. Selon la fabrication et l‘arme des munitions de même marque et de même type peuvent présenter une performance de tir et une précision variables.Sous réserve que l‘optique de visée, la munition et le montage aient été parfaitement sélectionnés, nous sommes en mesure de garantir une performance de tir hors du commun.Toute réclamation relative à la performance de tir doit être présentée dans un délai de 20 jours suivant la date d‘achat de l‘arme. Nous nous réservons le droit de faire examiner l‘arme par un institut indépendant (DEVA ou organisme national d‘épreuve). Si cet institut confirme une performance de tir excellente, nous serons en droit d‘exiger du client le remboursement des frais occasionnés.
3. Etendue de la garantie
La garantie ne saurait en aucun cas être prolongée ou renouvelée que ce soit pour l‘arme ou pour toute pièce de rechange. La durée de garantie appliquée aux pièces de rechange, est identique à celle appliquée à l‘arme.
4. Exclusion de la garantie
La garantie est exclue dans les cas suivants:• Dommages résultant de l‘usure normale, du
nonrespect du mode d‘emploi ou d‘un maniement non conforme et si l‘arme présente un dysfonctionnement mécanique de quelque ordre que ce soit.
• Dommages étant le fruit de conditions atmosphériques anormales.
• Réparations, usinage ou modifications de l‘arme par une tierce personne.
• Utilisation de munitions rechargées ou nonconformes à la CIP.
• Réalisation d‘un bronzage par une tierce personne.
La garantie ne couvre pas les instruments de visée optique et les systèmes de montage de lunette de visée autres que ceux de la marque Blaser Jagdwaffen GmbH. D‘autres droits, notamment ceux qui visent la compensation de dommages survenus endehors de l‘arme (dommages consécutifs) sont exclus sous réserve qu‘ une responsabilité n‘est pas définie par un jugement.
1. Garantie du fabricant
La garantie de la société Blaser Jagdwaffen GmbH est accordée en plus de la garantie légale du revendeur, à condition que la carte d‘arme à feu, cijointe, parvienne dûment remplie à la société Blaser Jagdwaffen GmbH dans les dix jours suivant la date d‘achat. La garantie n‘est accordée que pour le premier acquéreur, domicilé dans le pays où l‘arme a été achetée.La garantie ne couvre que les pièces métalliques et plastiques de l‘arme, ainsi que les montages de lunettes Blaser, mais pas l‘optique de visée. Les pièces en bois exigent un entretien spécifique et sont soumises en raison de leur caractère naturel à des modifications au fil du temps, la garantie ne s‘applique par conséquent pas à ces pièces.La garantie est accordée pour une durée de dix ans et prend effet à la date d‘achat . Elle englobe tous les défauts et dommages décelés sur l‘arme (pièces métalliques et plastiques), s‘il est prouvé qu‘ils relèvent de vices liés à la matière ou à des défauts de fabrication. Sous ces conditions, le fabricant prendra en charge les frais de pièces et de main d‘oeuvre. Pour l‘exécution des travaux liés à la garantie, l‘arme doit être remise à un revendeur agréé ou directement à l‘usine à Isny.Les risques et les frais de transport allerretour liés à une intervention sous garantie, sont pris en charge par le client. La prestation de garantie consistera, au choix pour le fabricant, en un remplacement ou en une réparation de pièce(s) défectueuse(s). Les pièces remplacées deviendront propriété du fabricant.
2. Garantie sur la performance de tir
La précision de tir d‘une arme dépend de plusieurs facteurs. Le facteur principal est la munition. Toutes les munitions ne conviennent pas à tous les canons et des variations très sensibles peuvent apparaître en terme de précision. L‘optique de visée et son montage, sont tout autant prépondérants. L‘effet de parallaxe, un réticule mal fixé, un défaut de fonctionnement des réglages du réticules et un montage défectueux sont des causes fréquentes qui agissent négativement sur la précision de l‘arme. C‘est pourquoi nous vous recommandons de n‘utiliser que des lunettes de visée de marque montées par un spécialiste et de bien définir le type de mu
072015 Sous réserve de modifications techniques.
fran
çais
1
2
3
4
10
5
6
711
12
8
9
63
Índice
Descripción de las partes
1 Palanca de amartillamineto (boton de seguro)2 Tope de cerrojo3 Cuerpo de cerrojo4 Báscula5 Cañon6 Delantera7 Palanca de cerrojo
8 Gatillo9 Culata
10 Asiento de montura Blaser11 Cargador12 Grupo cargadorgatillo extraible
PáginaDescripción de las partes 62 - 63 Normas generales de seguridad 64 - 65 1. Montaje y desmontaje 662. Seguro y bloqueo de cerrojo 673. Cargar el rifle 684. El disparo 68 - 695. Descargar 706. Quitar y poner el cerrojo 707. Intercambiar cañones 71 - 728. Cambiar el cabezal de cerrojo 72 - 739. Quitar y cambiar la delantera/ 73
Delantera Stutzen 74 - 7510. Miras abiertas (ajustables) 7611. Montaje del visor 76 - 7712. Montaje del visor (Tipo USA) 7713. Grupos de Calibres 7814. Maletines 7815. Unidad de gatillo R8 .338 Lapua Magnum 7916. Cuidado y mantenimiento 8017. Condiciones de garantía 81
espa
ñol
64
Normas generales de seguridad
Su nuevo rifle de repetición Blaser modelo R8 se diferencia de otros rifles de repetición por sus características especiales de diseño. A pesar del elevado nivel de seguridad de este arma, en ningún caso se debe dejar de tomar las precauciones necesarias que implica el hecho de empuñar un arma, así como observar el cumplimiento de la normativa legal vigente en cuanto al uso de armas. Antes de todo, compruebe que el manual de instrucciones que posee es el que correspondea su rifle R8: El modelo y el calibre se encuentran indicados en la parte posterior izquierda del cañon.
ATENCIÓN:Es imprescindible que lea todas las intrucciones de uso y manejo antes de usar el arma. Entregue el arma únicamente con este manual de instrucciones.
Pida además a su proveedor que le explique y le instruya en el manejo del arma como com-plemento a este manual de instrucciones.
Normas generales de seguridad para el uso de armas• Mantenga el arma y la munición siempre fuera
del alcance de personas no autorizadas.• Guarde siempre el arma separada de la muni
ción, bajo llave y fuera del alcance de personal no autorizado.
• Preste atención a las diposiciones legales vigentes sobre el uso y mantenimiento de armas y municiones.
• Familiaricese con el uso del arma y practique todas las funciones y formas de usarla antes de cargarla.Trate siempre el arma como si estuviera cargada y lista para disparar a menos que se haya convencido de lo contrario, abriendo el cerrojo y mirando la recámara (cañon). Un arma cerrada se debe tratar como un arma cargada.
• Cada vez que empuñe el arma, mantenga el cañón apuntando en una dirección, en la que no se encuentren personas, ni animales, ni objetos que pueda poner en peligro.
• Antes de cargar el arma, compruebe que no haya restos de aceite o de cuerpos extraños en la recámara o en el cañón, ya que estos pueden causar un desvío del punto de impacto. Cuerpos extraños en el cañón (p. ej. agua, nieve, tierra) pueden producir una obstrucción y tras el disparo causar daños al tirador o a las personas que estén a su lado. Asegúrese de que ningún cuerpo extraño entre en el cañón, incluso mientras usa el arma!
• Utilice exclusivamente munición que cumpla las exigencias de la CIP, en particular en lo relativo a la presión máxima de gas de uso, Pmax. Cada arma Blaser ha sido verificada por el Banco Oficial de Pruebas conforme a los requisitos de la Ley de Tiro y del Reglamento de Tiro con una presión de gas de tiro que supera como mínimo en un 25% la presión máxima admisible de gas de uso, Pmax. Si las presiones de gas de la munición empleada superan esta presión de gas, no estará garantizada al cien por cien la seguridad del usuario o de terceras personas. Esto también es válido en el caso de vainas de cartucho defectuosas.
• Compruebe el terreno alrededor, siempre antes de cada disparo.
• Apunte únicamente a un objetivo previamente identificado con claridad.
65
• Dispare únicamente cuando el rifle está bien acerrojado.
• No coloque el dedo índice en el gatillo a menos que quiera disparar.
• Si falla un cartucho, no abra el cerrojo hasta pasados unos 60 segundos. De esta forma evitará el peligro de la combustión posterior.
• Utilice protección auricular y ocular cuando dispare.
Descargue el arma• antes de cruzar obstáculos,• antes de subir o bajar del puesto de tiro,• antes de entrar en un edificio,• antes de subirse a un vehículo,• antes de entrar o aproximarse a una población• y tambien cuando deje el arma depositada en
algún lugar o se la entregue a alguien.
espa
ñol
66
1. Montaje y desmontaje
1.1. Montaje
• Encaje el cañón en la carcasa con la boca del mismo apuntando hacia arriba y sujételo firmemente.
• Apriete ambas tuercas de sujección del cañon con la llave Allen (SW5). No será necesaria ninguna prolongación.
R8 con cargador extraible:• Insertar el cargador en el compartimento del gru
po de gatillo desde arriba y presionar hacia abajo.Insertar desde abajo el cargador extraíble con el cargador incluido en la báscula hasta escuchar claramente que las dos pestañas encajan.
R8 sin cargador extraible:• Insertar el cargador desde la parte de arriba en el
compartimento habilitado para el mismo y presionar hacia abajo.
• Coloque el cerrojo en los dos raíles paralelos ubicados en la parte posterior de la carcasa con cuidado y deslicelo hacia adelante.
• Presione el cargador hacia abajo y empuje hacia adelante el cerrojo hasta que encaje y cierre sobre la báscula.
ATENCIÓN: El grupo cargadorgatillo solo puede encajarse en la báscula cuando el seguro de cargador no esté activado y por tanto la "S" en la parte inferior del mismo no sea visible.
ATENCIÓN:Durante el montaje, la palanca de cerrojo ha de mantenerse en su posición trasero. Lo que significa un ángulo de unos 45º. Cuando la palanca está casi en posición vertical, no puede insertarse. Girar la palanca hasta la posición de 45º para poder completar el proceso.
ATENCIÓN:Durante el montaje del R8, asegúrese siempre de que el cañón, cabezal de cerrojo y cargador corresponden al mismo calibre.
1.2. Desmontaje
• Presione suavemente hacia adelante el seguro con el pulgar (unos 2 mm). Al mismo tiempo, tire de la palanca de cerrojo hacia atrás con los dedos índice y corazón y tire entonces del cerrojo en línea recta hacia atrás.
• Descargue el arma (véase apartado 5).• Mantenga apretado el botón de retención mien
tras, con la otra mano, tira del cerrojo hacia atrás.• Afloje ambos tornillos de fijación al cañón con la
llave Allen (SW5).• Retire o extraiga el cañón.
67
2. Seguro y bloqueo de cerrojo
Sistema de SeguroEl sistema de seguro del Blaser R8 está basado en la tensión del muelle real del percutor. El boton de seguro permite que el muelle del percutor sea amartillado (tensionado o activado) justo aantes del disparo.En la posición de seguro o con el rifle desamartillado, la palanca de cerrojo también se bloquea para prevenir posibles aperturas involuntarias del cerrojo cuando estamos moviendo o manipulando el rifle, asegurando que el cerrojo siempre permanezca completamente cerrado.
2.1. Quitar el seguro (armartillar)
• Presione con el dedo pulgar con fuerza el seguro hacia adelante el dedo, de forma que el dispositivo encaje en la posición tensada.
• Se verá un punto rojo como señal de que el arma está sin seguro.
2.2. Volver a la posición de seguro (desamartillamiente)
• Para poner el rifle en seguro, apriete el botón de seguro con el pulgar hacia delante/abajo y deje que vuelva a su posición inicial (el punto rojo deja de ser visible).
ATENCIÓN:Bajo ninguna circunstancia debe poner los dedos en el gatillo cuando se amartilla o desamartilla el rifle (poner o quitar el seguro) Quizá usted esté acostumbrado a operar de esta manera en otro tipo de armas con per cutor exterior. En el caso del R8 esto podría hacer dispararse accidentalmente el rifle si este estuviera cargado.
2.3. Bloqueo de cerrojo
• Previene aperturas involuntarias del cerrojo. Actúa de forma automática cuando el arma tiene puesto el seguro y está completamente acerrojada.
2.4. Aperura el rifle en posición de seguro
• Deslizar ligeramente el botón de seguro con el pulgar hacia adelante (unos 2 mm).
• Al mismo tiempo, tire de la palanca del cerrojo hacia atrás con los dedos índice y corazón hasta abrir completamente el cerrojo.
espa
ñol
68
3. Cargar el rifle
3.1. Cargar
• Empuje hacia atrás el botón de seguro.• Abra el cerrojo (véase apartado 2.4).• Compruebe que el cañón y el cargador están
limpios de aceite y otros objetos extraños.• Compruebe y asegurese por sí mismo que siem
pre la munición utilizada corresponde al calibre del rifle.
R8 con cargador extraible• Quitar el grupo cargadorgatillo.• Colocar los cartuchos en el compartimento del
cargador y empujarlos hasta que encajen perfectamente.
• Insertar desde abajo el cargador extraíble cargado en la báscula hasta escuchar claramente que las dos pestañas encajan.
R8 sin cargador extraible• Coloque los cartuchos en el cargador y empujelos
hacia abajo hasta que encajen.
Capacidad del cargador:• Grupo "Mini" = 5 cartuchos• Grupo "Standard" = 4 cartuchos• Grupo "Medium" = 3 cartuchos• Grupo "Magnum" = 3 cartuchos• Grupo "Jeffery" = 2 cartuchos• Calibre 10,3 x 60R = m o n o t i r o
COMPRUEBE:Que el punto rojo no es visible y la palanca de cerrojo está completamente hacia delante. Entonces el arma está cargada, en posición de seguro y bloqueada contra una apertura involuntaria.
ATENCIÓN: Si la unidad cargadorgatillo es extraída cuando el cerrojo está cerrado y el rifle amartillado, el botón de seguro (botón de amartillamiento) se desamartillará de forma automática volviendo a posición de seguro. Así mismo, el muelle principal también se destensará. Si la unidad cargadorgatillo es extraída con el cerrojo abierto y amartillado, el botón de seguro (botón de amartillado) permanecerá amartillado. Y el muelle principal permanecerá tensado.
3.2. Seguro de cargador
Cada R8 con cargador extraible incorpora un seguro de cargador integrado en el propio cargador.• Cuando el cerrojo está abierto, empujar la palan
ca de bloqueo del cargador hasta que sea visible la "S". Entonces el cargador estará bloqueado.
• Una vez puesto el seguro el cargador no puede caerse o extraerse, pero si permite la carga por la parte superior abriendo el cerrojo como en cualquier R8 sin cargador extraible.
• Con el cerrojo abierto el seguro del cargador puede ser siempre activado o desactivado empujando la pestaña o botón de seguro.
4. El Disparo4.1. Disparo y repetició
• Quite el seguro del arma deslizando hacia a delante el botón del seguro.
• Apunte al objetivo y dispare.• Para repetir el disparo, tire del cerrojo hacia atrás
hasta el tope y despues empújelo todo hacia adelante de nuevo.
NOTA:Si la palanca de cerrojo no se empuja totalmente hacia delante hasta el tope, el cartucho, por razones de seguridad, no será disparado.
ATENCIÓN:Mientras el seguro se encuentre desplazado hacia delante, es decir sin seguro, el cerrojo se tensa automáticamente con cada nueva repetición. Si no se desea seguir disparando, se debe poner el seguro inmediatamente, dejando que el botón de seguro se desplace hacia atrás.
ATENCIÓN:Amartillar el rifle solo inmediatamente antes de disparar. Cuando no se vaya a disparar bloquear (desamartillar) inmediatamente el rifle. Si queremos volver a disparar, será necesario cargar (amartillar) el rifle de nuevo.
69
4.2. Opcional Gatillo Match-Caza de Atzl
El gatillo MatchCaza de Atzl permite elegir entre una presión del gatillo reducida, indicada para el tiro deportivo, y una presión de gatillo elevada destinada a la caza. El peso del gatillo se puede elegir sin herramientas mediante un selector situado en el marco del cargador desmontado (ilustración 4.2.1). Además del cargador intercambiable con selector, también es necesaria una unidad de gatillo especial en la carcasa (ilustración 4.2.2). El cambio del gatillo MatchCaza de Atzl solo puede realizarse en la fábrica Blaser Jagdwaffen GmbH en Isny.
Si en los calibres .375 Blaser Mag., .375 H&H Mag., .416 Rem. Mag. y .458 Lott la longitud total (longitud máxima de cartuchos L6) supera los 90,5 mm, estos cartuchos no pueden utilizarse en el gatillo MatchCaza de Atzl.
FuncionamientoAccionando el selector puede elegirse entre los dos pesos del gatillo:• Posición "Match" : 250 g / 0.55 lbs• Posición "Jagd" : 650 g / 1.43 lbs
NOTA:El cargador intercambiable MatchCaza de Atzl puede utilizarse sin límites en un rifle R8 sin gatillo MatchCaza de Atzl. En ese caso estará disponible el peso específico del gatillo montado y el cambio queda sin función. El uso de un cargador convencional en una carcasa con sistema MatchCaza de Atzl no es posible puesto que el cargador no encaja en la carcasa.
ATENCIÓN:El gatillo MatchCaza de Atzl reacciona de forma especialmente sensible cuando está en la posición "Match" (presión de gatillo muy baja). Cuando se desplaza el disparador hacia adelante y no habiéndose disparado, se ha de tener especial cuidado al retornar el gatillo a su posición habitual puesto que de no hacerlo se pueden producir disparos involuntarios. Se requiere prestar especial cuidado cuando el dedo que dispara entra en contacto con el gatillo cuando el arma esté cargada y/o amartillada.
ATENCIÓN:El rifle Blaser R8 está provisto de un gatillo directo. El ajuste sólo puede y debe ser modificado por el fabricante. Compruebe regularmente el funcionamiento correcto del gatillo con el arma descargada y con el seguro puesto. La presencia de aceite denso u otras impurezas puede afectar el funcionamiento del gatillo y causar fallos en el funcionamiento.
Ilu. 4.2.2.
Ilu. 4.2.1.
f Cambio en el marco
f Unidad de gatillo especial en la carcasa
espa
ñol
70
5. Descargar 6. Quitar y poner el cerrojo
5.1. Descargar
• Desamartillar, aprentando el seguro hacia abajo y hacia atras con el pulgar.
• Abra y tire hacia atrás el cerrojo (véase apartado 2.4), al mismo tiempo, el cartucho será extraido del cañón.
R8 con cargador extraible:• Retirar el cargador presionando en los dos boto
nes y quitar los cartuchos sobrantes empujando con los dedos hasta que salgan del cargador.
• R8 sin cargador extraible:• Empujar los cartuchos sobrantes con el pulgar
hasta sacarlos del cargador y retirarlos.• Asegúrese siempre de que el cañón y el cargador
están vacios.
6.1. Quitar el cerrojo
• Desamartille y descargue el rifle.• Tire del cerrojo completamente hacia atrás.• Mantener presionado el tope de retención y al
mismo tiempo, con la otra mano tire del cerrojo hacia atrás hasta que salga del todo.
En los calibres .222 Rem., .223 Rem., 5,6x50 Mag., 22250, .243 Win., 6,5x55, 6,5x57, 7x57, 7,5x55, .308 Win. y 8x57 IS se incorpora un tope adicional de retención situado en el lateral derecho del cargador. Para quitar el cerrojo de un rifle de los calibres anteriormente mencionados, seguir los siguientes pasos:
• Apriete el lateral derecho del cargador hacia abajo. Con esto deja de funcionar este tope de retención.
• Tire del cerrojo hacia atrás hasta el tope normal.• Mantenga entonces presionado el tope de reten
ción mientras, con la otra mano, tira del cerrojo hacia atrás.
6.2. Poner el cerrojo
• Mantenga apretado el cargador completamente hacia abajo en la carcasa.
• Con cuidado coloque el cerrojo en los dos railes paralelos ubicados en la parte posterior de la carcasa.
• Deslizar entonces el cerrojo hasta que encaje completamente acerrojado.
71
7. Intercambiar cañones
Existen 6 grupos de calibres (véase apartado 13). Al cambiar el cañón de un grupo de calibre a otro, es necesario cambiar el cabezal de cerrojo para que coincida con el grupo de calibre del cañón que se haya colocado. La correspondencia entre cabezal y cañón se puede comprobar en la tabla en apartado 13. Además, los cabezales de cerrojo y los cañones tienen un símbolo troquelado con el grupo de calibre al que corresponden. Estas marcas deben coincidir tras el montaje.
Dentro de los grupos de calibre, es posible cambiar los cañones como se desee sin tener que cambiar el cabezal de cerrojo.
Grupos de calibres:Mini marcado MIStandard marcado STMedium marcado MEMagnum marcado MAJeffery marcado JE10,3 x 60 R marcado CH
Asegúrese que también se coloca el cargador correspondiente al nuevo calibre. Las denominaciones de calibres están marcadas en un lateral del cargador (véase apartado 7.2).
NOTA: Con el cañon del calibre 10,3x60R, se suministra una insercción monotiro. No existe un cargador.
7.1. Intercambiar el cañón
• Desamartille y descargue el rifle.• Tire del conjunto del cerrojo por completo hacia
atrás y retírelo.• Afloje por completo ambas tuercas de fijación
del cañon con una llave Allen (SW5). Las tuercas permanecen en sus guías y no se pueden perder.
• Separe el cañón de la báscula.• Coloque el nuevo cañón sobre la carcasa.• Apretar de nuevo lo dos tornillos con ayuda de
la llave Allen.
R8 con cargador extraible:• Insertar desde arriba el cargador correspondiente
al calibre del cañón dentro del cargador extraíble. Insertar desde abajo el cargador extraíble en la báscula hasta escuchar claramente que las dos pestañas encajan.
R8 sin cargador extraible:• Retirar el cargador (posiblemente el visor tenga
tambien que ser quitado véase 12.2).• Insertar el cargador correspondiente al calibre del
nuevo cañón desde arriba dentro de la cavidad cargador.
• Comprobar, si el grupo de calibre marcado en el cabezal de cerrrojo ("MI", "ST", "ME", "MA", "JE", "CH", véase apartado 7 y Ilu. 7.1.) corresponde al grupo del nuevo cañón intercambiado.
• Si el cabezal de cerrojo tambien ha de ser cambiado ver apartado 8.
NOTA:Asegurarse siempre que el cañón está limpio y libre de obstrucciones. Aceite excesivo, grasa de armas entre el cañón y la carcasa puede tener un efecto contraproducente en la precisión del rifle.
espa
ñol
72
8. Cambiar el cabezal de cerrojo
7.2. Quitar el cargador
R8 con cargdor extraible:• Abrir el cerrojo.• Quitar si hubiera el cartucho de la recámara.• Quitar el cargador y vaciarlo.• Utilizar el dedo índice y el pulgar para agarrar
la bandeja del cargador, presionar la pestaña izquierda y al mismo tiempo tirar del cargador hacia afuera.
• Insertar el cargador correspondiente al calibre desde arriba en la cavidad para el mismo.
R8 sin cargador extraible:• Desamartille y descargue el rifle.• Quitar el cerrojo.• Extraer el cargador con el dedo índice.• Insertar el cargador correspondiente al nuevo ca
libre desde la parte de arriba del compartimento para el cargador.
8.1. Quitar el cabezal de cerrojo
Lo más recomendable es que pida a su armero de confianza la realizacion de una demostra-ción de este proceso.
• Desamartille y descargue el rifle.• Abrir el cerrojo y quitarlo.• Colocar el cerrojo sobre una superficie plana,
boca arriba.• Utilizar un pequeño destornillador u objeto si
milar para empujar la pestaña de retención a la izquierda, hacer palanca y hacerla girar.
• Girar el cabezal en el sentido contrario a las agujas del reloj un cuarto de vuelta y tirar de él hacia delante.
8.2. Instalar el cabezal de cerrojo
• Levantar la pestaña de retención del cuerpo del cerrojo.
• Empujar el cabezal sobre la aguja percutora hasta que haga tope dentro del alojamiento donde va ubicado y girar un cuarto en el sentido de las agujas del reloj (véase aprta do 8.2).
• Deje de girar cuando la pestaña de retención pueda ser roscada en las estrías del cabezal.
NOTA: Para facilitar la colocación, recomendamos llevar el percutor hacia atras y bajarlo con el pulgar de la otra mano durante el proceso.
• Vuelva a girar la pestaña hasta que encaje dentro del cerrojo venciendo la presión del muelle.
73
9. Quitar/Cambiar la delantera
El Blaser R8 en sus versiones Jadgmatch y Safari cuenta con una delantera especial,más ancha. Cuando colocamos un cañón Safari o Jagdmatch en una versión standard del R8 es necesario un cambio de esta delantera.
9.1. Quitar la delantera
• Flojar el tornillo de la delantera con una llave Allen (SW5) y tirar hacia delante de la delantera.
9.2. Montar la delantera
• Colocar la delantera en la carcasa y apretar el tornillo de nuevo.
ATENCIÓN:Si el pasador de retén no está completamente encajado aparecerá un botón de aviso en la parte exterior del raíl. Sólo es posible colocar el cerrojo en la carcasa si el botón de aviso ha desaparecido, con lo cual el pasador de retén ha encajado perfectamente.
NOTA:Los cabezales para cerrojos de zurdo están señalados con una "L" junto al grupo de calibre.
ATENCIÓN:El cabezal se compone de dos partes fundamentales, el cabezal del cerrojo propiamente dicho y collar de acerrojamiento radial, ambas partes están aseguradas por un remache. Está terminantemente prohibido quitar o aflojar ese remache! Disparar con el rifle con el remache manipulado pude ocasionar daños irreparables en el tirador o en aquellas personas que estén a su lado.
espa
ñol
74
9.3. R8 Professional Success Stutzen
Todos los modelos R8 Stutzen están disponibles con dos longitudes de cañón (52 cm y 58 cm) y dos contornos de cañón diferentes (Standard con 17 mm y Semi Weight con 19 mm de diámetrode boca).
Versión de guardamano Stutzen Longitud del cañón/Contorno del cañón
Versión 1 520 mm / 17 mm
Versión 2 520 mm / 19 mm
Versión 3 580 mm / 17 mm
Versión 4 580 mm / 19 mm
9.4. Cambio del cañón
Quitar el cañón:• Desmartille y descargue el rifle.• Tire del conjunto del cerrojo por completo hacia
atrás y retírelo.• Afloje por completo ambas tuercas de fijación
del cañón con una llave Allen (SW5). Las tuercas permanecen en sus guías y no se pueden perder.
• Levante el cañón en el área de la cámara y empújelo hacia delante (consulte la fig. 9.2).
NOTA:Unos imanes permanentes insertados en el extremo del guardamano Stutzen aseguran un firme agarre entre el extremo del guardamano Stutzen y el cañón. Resulta más fácil retirar el cañón cuando éste se levanta en el área de la recámara y se empuja hacia deante.
Insertar el cañón:
COMPRUEBE:¡Su guardamano Stutzen tiene que coincidir con el diámetro y la longitud del cañón!
• Coloque el cañón de recambio la báscula (consulte la fig. 9.3).
• Apriete a mano las dos tuercas de fijación del cañón con la llave Allen (SW5).
9.5. Conversión del R8 Professional Success en el R8 Professional
Success Stutzen
• Desmartille y descargue el rifle.• Tire del conjunto del cerrojo por completo hacia
atrás y retírelo.• Afloje por completo ambas tuercas de fijación
del cañón con una llave Allen (SW5). Las tuercas permanecen en sus guías y no se pueden perder.
• Extraiga el cañón de la báscula.• Afloje ambos tornillos en el extremo del guar
damano (consulte la fig. 9.4) con la llave Allen (SW5) y quítelos con las arandelas de seguridad.
NOTA:No pierda las arandelas de seguridad (consulte la fig. 9.4a).
• Doble hacia abajo y postizo o punta el extremo del guardamano.
• Inserte y encastre el guardamano Stutzen.• Inserte ambos tornillos con arandelas de seguri
dad en el extremo del guardamano y apriételos con los dedos (consulte la fig. 9.5).
75
ATENCIÓN:Los campos magnéticos permanentes también pueden borrar datos de medios de almacenamiento magnéticos, como por ejemplo discos de ordenador, discos rígidos, tarjetas bancarias y tarjetas de crédito, inutilizándolos. Por lo tanto, los imanes permanentes no deberían entrar en contacto cercano con estos medios de almacenamiento.
NOTA:El R8 Stutzen con cañón y el R8 Stutzen sin cañón han sido examinados por TÜV Süd conforme a la “Instrucción de embalaje 953 para material magnetizado UN2807”. El producto no está clasificado como material magnetizado UN2807. El producto puede ser transportado por aeronaves comerciales y de carga.
NOTA:Para no afectar el rendimiento al disparar y asegurar un funcionamiento impecable, le rogamos que preste mucha atención a los siguientes requisitos:• Asegúrese siempre de que el ajuste del cañón
esté limpio!• Asegúrese además de que la superficie de sopor
te del postizo del guardamano Stutzen también esté limpio!
• Los restos de aceite y grasa para armas entre el cañón y la báscula afectan de manera negativa a la precisión de los rifles.
ATENCIÓN:La punta del guardamano Stutzen cuenta con un imán permanente para mantener el guardamano posición (consulte la fig. 5). El campo magnético del imán permanente puede afectar el funcionamiento de implantes cardíacos o marcapasos. Por lo tanto, la punta del guardamano Stutzen no debería entrar en contacto cercano (5 cm o menos) con un implante cardíaco o marcapasos.
5 cm distancia mínima hasta el final de la delantera Stutzen!
espa
ñol
76
11. Montaje del visor
El Blaser R8 viene preparado para el montaje original Blaser. Damos por supuesto que su armero ha montado correctamente la mira telescópica en la montura.
11.1. Instalación del visor
• Abra las pestañas de las palancas de sujeccion de la montura con el pulgar.
• Sujete la mira con su mano derecha por la parte central del tubo sobre la montura y alcance la palanca de cierra con el pulgar.
• Sostenga el rifle por la delantera con su mano izquieda y apoye la culata en el muslo.
• Inserte los dos extemos redondeados de la montura cuidadosamente en los dos orificios a tal fin sobre la parte superior del cañón. Gire la palanca delantera hacia la izquierda y mantengala en esta posición.
• Cierre los dos elementos de sujección, primero el de la parte delantera y luego el trasero con el pulgar hasta que hagan tope y encajen en su correcta posición. (Si este proceso resulta demasiado fácil o bien requiere fuerza, entonces la montura estará mal colocada. Haga que su armero coloque la montura de acuerdo a las instrucciones. La presión ideal para cerrar estos elementos podrá ser comparable a la necesaria para activar o desactivar el botón de seguro).
• Cierre las dos palanquitas de la montura.
ATENCIÓN:Asegúrese siempre que las superficies de están limpias y libres de grasa.
10.Miras abiertas
10.1. Ajuste del punto de mira en altura
• Introducir la llave Allen SW 1.3 en el agujero de la base del punto de mira y girarla cuanto sea necesario:
• Punto de mira con muelle incorporadogiro a la izquierda = tiro mas bajo,giro a la derecha = tiro más alto.
10.2. Ajuste lateral del alza
• El alza tiene agujero a derecha e izquierda para la llave Allen SW 1.3.
• En caso de disparo a la izquierda: Desplace el visor hacia la derecha; para ello, afloje el tornillo izquierdo y apriete el tornillo derecho.
• En caso de disparo a la derecha: Desplace el visor hacia la izquierda; para ello, afloje el tornillo derecho y apriete el tornillo izquierdo.
10.3. Mira Safari con regulación de altura y ajuste lateral
Desde junio de 2014 la mira Safari de Blaser se ha vuelto regulable. El ajuste se realiza con una llave Allen SW2 de igual manera que en la mira abierta (véase más arriba).Las miras Safari anteriores a esta fecha no son regulables, sino que incluyen de fábrica una altura estándar del punto de mira de 6 mm a punto de impacto 30 m. Otras alturas y alzas son opcionales con coste adicional.
77
11.2. Quitar la visor
• Sujete el arma por la delantera con la mano izquierda y apóyela en el muslo.
• Abra las tapas de las palancas de sujeccion.• Gire primero la palanca trasera hacia la izquierda
con el pulgar hasta que haga tope.• Sujete la mira telescópica por el tubo central con
la mano derecha.• Gire la palanca delantera hacia la izquierda con el
pulgar hasta que haga tope.• Retire la mira telescópica.
ATENCIÓN:Con disparos con calibre pesados, no se descarta que se produzcan heridas si la distancia entre el ojo y la mira telescópica no es la suficiente, así como si no se apoya la culata en el hombro de forma correcta.Sobre todo con calibres pesados se debe prestar atención a una mayor distancia entre el ojo y la mira telescópica, así como a un apoyo correcto de la culata en el hombro.
12. Montaje del visor (Tipo USA)
12.1. Colocar la mira telescópica
• Gire ambos tornillos laterales Allen SW1/8" en la montura un par de vueltas hacia la izquierda
• Sujete la mira telescópica por el tubo central con la mano derecha.
• Sujete el arma por la delantera con la mano izquierda, apóyela en muslo.
• Coloque la montura de la mira telescópica con cuidado, poniendo ambos pivotes redondos en los fresados ovalados en la parte superior derecha del cañón. Inclínelo hacia la izquierda y sujete la mira con la mano izquierda.
• Apriete a mano los dos tornillos laterales de la montura con la llave Allen SW1/8".
12.2. Quitar la mira telescópica
• Sujete la delantera y la mira telescópica con la mano izquierda y apoye la culata en el muslo.
• Afloje del montaje los dos tornillos laterales Allen SW1/8" un par de vueltas.
• Retire la mira telescópica.
espa
ñol
78
Mini "MI":
.222 Rem. .223 Rem.
.204 Ruger
Standard "ST":
.22250 7x64
.243 Win. .308 Win.
6XC .3006
6,5x55 SE 8x57 IS
6,5x57 8,5x63
6,5x65 RWS 9,3×57
.270 Win. 9,3x62
Medium "ME":6,5x68 8x68 S
7,5x55 Swiss
Magnum "MA":
.257 Weath. Mag. .300 WSM
.270 Weath. Mag. .338 Blaser Mag.
.270 WSM .338 Win. Mag.
7 mm Blaser Mag. .375 Blaser Mag.*
7 mm Rem. Mag. .375 H & H Mag.*
.300 Blaser Mag. .416 Rem. Mag.*
.300 Win. Mag. .458 Lott*
.300 Weath. Mag. .458 Win. Mag.
Jeffery "JE":
.500 Jeffery
Suiza "CH":
10,3x60 R
* No se le puede combinar el gatillo MatchCaza de Atzl con el calibre indicado.
14. Maletines
El maletín especial ABS con doble forro para el R8 cuenta con 3 cerrojos. Cabida para un R8 y sus accesorios permite un práctico transporte del mismo.
Maletín BPara Blaser R8 con delantera y visor montado. También disponible para monotiros.Dimensiones externas LxAxA: 78x26x9 cm
Maletín CPara todos los Blaser monotiro y R8 con delantera colocada. Cuenta con compartimento para un cañon y visor de repuesto. Dimensiones externas: LxAxA: 84x45x11 cm
13. Grupos de Calibres
Por favor, tenga en cuenta que por motivos técnicos, no se puede garantizar una constan-te disponibilidad de todos los calibres antes mencionados.
79
15. Unidad de gatillo R8 .338 Lapua Magnum
GeneralidadesLa unidad de gatillo de fabricación especial garantiza un fiable transporte de los cartuchos, incluso de los de máxima longitud (máx. L6 según CIP), permitiendo así por primera vez a cazadores activos en el extranjero y a tiradores de Larga Distancia disparar con el R8 empleando el preciado calibre .338 Lapua Magnum.
Modo De FuncionamientoLa nueva unidad de gatillo puede utilizarse en todas las culatas R8 Professional Success.
ATENCIÓN:Es imprescindible, sin embargo, que la recámara, cañón y unidad de gatillo se correspondan con el calibre 338 Lapua Magnum. La identificación se encuentra en la recámara del cabezal en el extremo posterior del cañón junto al nº de serie. Para no confundir la unidad de gatillo .338 Lapua Magnum, el amortiguador de cartuchos optimizado va pegado y es de color naranja, y además, la unidad de gatillo lleva la correspondiente inscripción (ver fig. 1).
Ejecuciones Técnicas
Unidad de gatillo 338 LAPUALongitud de cartucho: hasta la longitud máxima definida por CIPUnidad de gatillo ATZL .338 LAPUALongitud de cartucho: Diferente de la longitud máxima CIP: 92,2 mm, máx.
Cuidado y mantenimientoEl cargador y la unidad de gatillo deberán mantenerse siempre limpios y exentos de cuerpos extraños.
» Amortiguador de cartuchos optimizado de color naranja y pegado
» Inscripción de calibre (sólo 338 LAPUA Mag.)
espa
ñol
80
16. Cuidado y mantenimiento
Para el cuidado del arma, se deben usar exclusivamente productos apropiados para este fin.
Cañón:Los cañones del rifle Blaser se fabrican con acero templado de alta calidad, en cuanto a máxima exigencia en cuanto a pureza, homogeneidad y propiedades mecánicas y dinámicas.La calidad del material se controla y documenta mediante pruebas de fábrica y controles de calidad propios y de forma constante.
Exterior del cañón:La superficie exterior del cañón está nitrurada por plasma y pavonada, lo que le confiere una extraordinaria resistencia a los arañazos y – si se conserva correctamente – una muy buena resistencia a la corrosión, aunque no proporciona una protección anticorrosión al 100%.Le recomendamos que mantenga limpia la superficie y la proteja aplicando regularmente una fina capa de protección empleando un aceite para armas adecuado. En especial, si el cañón ha estado húmedo o ha sudado dentro de una funda sintética, debe secarse y lubricarse ligeramente tal como se ha descrito.
Interior del cañón:La superficie interior del cañón ha sido forjada en frío y posee una muy buena calidad superficial. La superficie lisa mejora la protección anticorrosión; no obstante, no sustituye en ningún caso a una limpieza y conservación cuidadosas. Le recomendamos encarecidamente que limpie el aceite y seque con un trapo la recámara y el cañón antes de usar su arma para evitar problemas de precisión del arma.Después de usar el rifle debe limpiar y conservar el cañón, ya que los restos de pólvora dentro de la recámara y el cañón atraen la humedad. La recámara requiere una atención especial: A través del cartucho en algunas ocasiones llega sudor de la mano a la recámara que tiene un efecto agresivo y puede producir corrosión.Si se forman depósitos de residuos perceptibles de proyectiles se recomienda realizar una limpieza química del cañón. Tras la limpieza química del cañón, es necesario secar el cañón y, en particular, también la recámara, y lubricarlos ligeramente.
ATENCIÓN:¡El arma no debe guardarse en ningún caso con la boca del cañón tapada o taponada ni con un protector de boca de cañón! ¡Es imprescindible prestar atención a las indicaciones del fabricante en cuanto a mantenimiento de las distintas partes del arma!
Piezas Metálicas:Mantener siempre limpias y ligeramente lubricadas todas las piezas metálicas exteriores.El aceite para maderas no es apropiado para el cuidado partes metálicas.
Cargador:Mantener siempre el cargador limpio y libre de residuos!
Maderas:Todas las partes de madera de armas de caza Blaser están acabadas al aceite. Por ello recomendamos un mantenimiento de madera convencional.El aceite de armas no es apropiado para el cuidado de las maderas!
Indicaciones de cuidado para las insercio-nesde piel Professional Success:Las almohadillas de cuero de la R8 Professional Succes llevan una capa de impregnación, por lo que no es necesario limpiarlas regularmente. Para su cuidado es adecuado el tratamiento para cuero de Blaser.
Óptica:Véase el manual de conservación del fabricante de la óptica.
ATENCIÓN:Para la conservación de las armas de caza, hay que tener cuidado de que no se introduzca nada de aceite ni de grasa en el sistema de gatillo y cerrojo. Bajo determinadas circunstancias, los aceites y las grasas pueden resinificarse (endurecerse) y, con ello, provocar fallos de funcionamiento peligrosos. Antes de cada temporada de caza y de cada viaje de caza, lleve su arma a su concesionario especializado para que la revise. Toda arma es un aparato técnico que necesita someterse a un control regular.
81
17. Condiciones de garantía
la misma elaboración puede tener una eficacia de disparo y un punto de impacto que varíen de un lote de fabricación a otro y de un arma a otra.Con la munición, la óptica de la mira telescópica y el montaje Blaser asegura una excelente precisión en el de disparo.Toda reclamación sobre la precisión del arma debe realizarse por escrito durante los primeros 20 días tras la fecha de compra. Blaser se reserva el derecho de presentar el arma a un instituto independiente para su inspección (DEVA o la Oficina Nacional de Tiro). Si el instituto confirma la excelente precisión, estamos autorizados a exigir del cliente el pago de los gastos ocasionados.
3. Alcance de la garantía
Los trabajos realizados bajo la garantía no causan la prolongación o renovación del periodo de garantía del rifle o alguna de sus piezas. El periodo de garantía de de piezas instaladas termina al mismo tiempo que el periodo de garantía del propio rifle.
4. Cancelación de la garantía
La garantía quedará cancelada en caso de:• Daños producidos como consecuencia de un
desgaste normal, inobservancia del manual de instrucciones, utilización o manipulación inadecuadas o de daños de cualquier tipo en el mecanismo.
• Daños producidos como consecuencia de fuerza mayor o influencias ambientales.
• Reparaciones, operaciones de reequipamiento o modificaciones del arma a cargo de terceros.
• Utilización de munición recargada o no homologadapor el CIP.
• Realización de un pavonado a cargo de terceros.
La garantía no cubre otras reclamaciones, en particular aquellas de indemnización por los daños generados a terceros por el uso indebido del arma (daños consecuenciales) salvo que la legislación vigente exija de forma obligatoria una responsabilidad.
1. Garantía del fabricante
La garantía de armas de caza Blaser (Blaser Jagdwaffen GmbH) se ofrece adicionalmente a los derechos de garantía legales del comerciante, con la condición de que Blaser Jagdwaffen GmbH reciba la tarjeta de armas adjunta, completamente rellenada durante los diez primeros días tras la fecha de compra. La garantía es ofrecida únicamente al comprador original, cuya residencia se encuentra en el país donde se realizó la compra.
La garantía solamente cubre las piezas de metal y de plástico del arma y los monturas originales Blaser. Las piezas de madera del arma requieren un cuidado especial, y están condicionados, como producto natural, a ciertos cambios. Las partes de madera están excluidas de la garantía.
El período de garantía cubre diez años, comenzando a partir de la fecha de compra, y abarca todas las deficiencias y daños del arma (de las piezas de metal y de plástico) que puedan comprobarse como fallos de material o de fabricación. Dentro de este marco, el fabricante asume los gastos de material y de tiempo de trabajo. Para la ejecución de los trabajos de garantía se debe entregar el arma a su distribuidor autorizado o a la compañía fabricante en Isny.
El cliente se hace cargo del riesgo y de los costes de envío y de devolución. La garantía cubre la reparación o la sustitución de la pieza defectuosa, según decida el fabricante. Las piezas reemplazadas serán propiedad del fabricante.
2. Garantía sobre la eficacia de disparo
La precisión de disparo de un arma depende de muchos factores, siendo el más importante la munición. No dispara igual de bien cualquier cañón con cada tipo de munición, pudiendo existir considerables diferencias de precisión. La óptica de la mira telescópica y su montaje son igualmente importantes. Paralaje, retículas flojas, defectos de ajuste de las retículas y un montaje defectuoso son las causas más comunes de la mala precisión. Por ello, debería utilizar miras telescópicas de marcas acreditadas, montadas por su armero y adaptar la munición a su arma, probando para ello diferentes tipos de munición. La munición del mismo fabricante y de
072015 Sujeto a cambios tecnicos.
espa
ñol
1
2
34
10
5
6
711
12
8
9
83
Содержание
Обозначение основных частей
1 Взводитель ударника (шпаншибер)2 Останов затвора3 Затвор4 Стрельба5 Ствол6 Цевье7 Рукоятка затвора
8 Спусковой крючок9 Приклад
10 Открытый прицел11 Вставка магазина12 Сменный магазин
СтраницаОбозначение основных частей 82 - 83 Правила безопасности 84 - 85
1. Сборка, разборка 862. Система взвода и блокировка затворного рычага 873. Заряжание карабина 884. Стрельба 88 - 895. Разряжание 906. Установка затвора 907. Замена ствола 91 - 928. Замена личинки затвора 92 - 939. Демонтаж/смена цевья/ 93
цевья Stutzen 94 - 9510. Открытый прицел 9611. Установка оптического прицела 96 - 9712. Установка оптического прицела (США) 9713. Группы калибров 9814. Кейс 9815. Корпус магазина R8 .338 Lapua Magnum 9916. Уход за оружием 10017. Гарантийные условия 101
русский
84
Правила безопасности
Ваш новый карабин Blaser с продольно-скользящим затвором модели R8 значительно отличается своими конструктивными особенностями от других карабинов. Повышенный уровень безопасности Вашего карабина Blaser не должен служить поводом легкомысленного об-ращения с этим оружием или пренебрежения техникой безопасности и законами об оружии в Вашей стране. В первую очередь проверьте наличие правильного руко-водства по эксплуатации: Обозначение модели R8 и ка-либр карабина находятся на задней левой части ствола.
ВНИМАНИЕ:Необходимо прочитать эту инструкцию полностью пе-ред первичным использованием карабина. Передавай-те оружие только вместе с инструкцией.
Дополнительно к этому руководству по эксплуата-ции Ваш оружейник расскажет об устройстве нового карабина, а так же покажет и объяснит Вам как пра-вильно обходиться с ним.
Правила безопасного обращения с оружием:
• Следите, что бы оружие и патроны не попали в руки посторонних лиц.
• Храните оружие отдельно от патронов под замком, недоступно для посторонних.
• Соблюдайте законы об оружии регулирующие ноше-ние и хранение оружия и патронов.
• Основательно ознакомьтесь со всеми функциями Вашего оружия и поупражняйтесь с незаряженным оружием до применения на практике.
• Исходите всегда из того, что оружие заряженно и гото-во к выстрелу, пока не убедитесь в противоположном, открыв затвор и проверив наличие патрона в патрон-нике. Обходитесь с незаряженным оружием так же осторожно, как и с заряженным.
• Всегда направляйте ствол в безопасное направление, в котором невозможно подвергнуть опасности посто-ронние лица или повредить что либо.
• Перед заряжанием оружия проверьте, не находятся ли в стволе остатки масла или другие посторонние пред-меты. Остатки смазки в патроннике или канале ствола могут значительно повлиять на изменение средней точки попадания (СТП)! Попадание в канал ствола воды, снега, грязи и прочих посторонних предметов может привести при выстреле к разрыву ствола и тем самым к серьезному ранению стрелка и находящихся по близости посторонних лиц!
• Пользуйтесь исключительно патронами, которые соответствуют требованиям CIP, в особенности относительно максимального рабочего давления газа Pmax. Каждый карабин фир-мы Blaser проходит контрольный государственный отстрел в соответствии с немецкими законами об оружии, при котором используются патроны с мак-симальным давлением, которое на минимум 25% превосходит рабочее давление газа Pmax. Если при-меняемые Вами патроны превосходят по своему ра-бочему давлению газов те, которые используются при государственном отстреле, фирма Blaser не может гарантировать безопасность стрелка и окружающих. То же самое действительно и для гильз, которые по-теряли способность к обтюрации.
• Заряжайте Ваше оружие только непостредственно перед применением
• Взводите Ваше оружие лишь непосредственно перед выстрелом. При этом направляйте ствол в безопасное направление.
• Перед каждым выстрелом проверяйте местность до
85
и после цели.• Направляйте оружие только на ту цель, которую Вы
однозначно опознали.• Ложите палец на спусковой крючок, только если Вы
собираетесь произвести выстрел.• Стреляйте только при наличии пулеуловителя.• При осечке открывайте затвор только по истечению
одной минуты во избежание возможного взрыва па-трона.
• Пользуйтесь наушниками во время стрельбы.
Разрядите оружие• перед преодолеванием препятствий,• перед подъёмом на вышку и её покиданием,• прежде чем войти в помещение,• прежде чем сесть в автомобиль,• перед входом в населенный пункт,• а так же, если Вы на время откладываете оружие или
передаете его в другие руки.
русский
86
1. Сборка, разборка
1.1. Сборка
• Вставьте ствол в ствольную коробку и придерживайте его одной рукой.
• С помощью приложенного шестигранного ключа (SW5) затяниете обе гайки крепления ствола. Не применяйте удлинение!
R8 со сменным магазином:• Вставьте вставку магазина в корпус магазина и уто-
пите её в нём.• Вставить сменный магазин вместе с вставкой магази-
на снизу в затворную коробку и прижать, чтобы обе кнопки магазина защелкнулись с характерным звуком.
R8 без сменного магазина:• Вставьте вставку магазина в корпус магазина и уто-
пите её в нём.• Вставьте затвор с направляющими шинами в стволь-
ную коробку параллельно к пазам для направляющих.• Нажмите на вставку магазина и закройте затвор, дове-
дя его вперед до упора.
ВНИМАНИЕ: Сменный магазин можно вставить в ствольную коробку только в том случае, когда деактивирован предохрани-тель магазина и не видна буква "S" на дне магазина.
ВНИМАНИЕ:При установке затвора, рукоятка затвора должна на-ходиться в заднем положении, то есть под углом при-мерно в 45° к оси ствола. Если рукоятка затвора нахо-диться перпендикулярно к стволу, затвор установить невозможно. Отведите рукоятку назад до фиксации её в положении 45°.
ВНИМАНИЕ:Во время сборки следите за тем, что бы ствол, затвор и вставка магазина соответствовали калибру.
1.2. Разборка
• Подвиньте большим пальцем взводитель /шпаншибер вперёд на примерно 2 мм, одновременно поверни-те рукоятку затвора назад указательным и средним пальцами и отведите затвор прямолинейно назад.
• Разрядите оружие (см. пункт 5).• Нажмите на кнопку останова затвора и держите её на-
жатой. Одновременно извлеките затвор из ствольной коробки другой рукой движением назад.
• Отвинтите гайки крепления ствола с помощью прило-женного шестигранного ключа SW5.
• Извлеките ствол из ствольной коробки.
87
2. Система взвода и блокировка затворного рычага
Система взводаКонцепт безопасности карабина Blaser R8 основан на невзведённой пружине ударника: Клавишей взводителя ударника/ шпаншибера боевая пружина взводится не-посредственно перед выстрелом, при перезарядке она остаётся взведённой. После выстрела пружину ударни-ка можно снять с боевого взвода.В невзведённом состоянии рукоятка затвора блокирует затвор от случайного открытия при переноске, если за-твор был закрыт до конца.
2.1. Постановка на боевой взвод
• Большим пальцем подвинуть взводитель ударника/шпаншибер до упора вперёд и убрать палец с клави-ши вверх, при этом клавиша фиксируется в переднем положении.
• Сигнал постановки карабина на боевой взвод - крас-ный квадрат - становится видимым под шпаншибе-ром. Карабин взведён и готов к стрельбе.
2.2. Снятие с боевого взвода
• Для снятия карабина с боевого взвода требуется на-жать шпаншибер большим пальцем вперёд и вниз и дать отойти ему в исходное положение. Красный ква-драт исчезает под клавишей шпаншибера.
ВНИМАНИЕ:При взводе и снятии с боевого взвода ни в коем слу-чае не касаться пальцем спускового крючка (как это делается у моделей оружия с наружными курками)! Это приведёт к выстрелу!
2.3. Блокировка затворного рычага
• Предохраняет от случайного открытия затвора, напри-мер при переноске карабина. Она включается авто-матически, если затвор закрыт до конца и ударник не взведён.
2.4. Открывание затвора в невзведённом состоянии
• Большим пальцем легонько подвиньте шпаншибер на 2 мм вперёд.
• Одновременно поверните рукоятку затвора указатель-ным и средним пальцами от ствола и отведите затвор прямолинейно назад.
русский
88
3. Заряжание карабина
3.1. Заряжание
• Снимите карабин с боевого взвода отведением шпан-шибера назад.
• Откройте затвор (см. пункт 2.4).• Удалите масло из канала ствола и патронника и про-
верьте их на наличие посторонних предметов.• Обязательно удостоверьтесь в том, что патроны соот-
ветствуют калибру Вашего карабина.
R8 со сменным магазином• Извлеките сменный магазин.• Положите патрон на губки магазина и сильно вдавите
его в магазин, до прохода через губки магазина.• Вставить снаряженный сменный магазин снизу в за-
творную коробку и прижать, чтобы обе кнопки магази-на защелкнулись с характерным звуком.
R8 без сменного магазина• Положите патрон на губки магазина и вдавите его в
магазин, до тех пор пока он не пройдёт через губки магазина.
Вместимость магазина:• Группа калибров "мини" = 5 патронов• Группа калибров "стандарт" = 4 патрона• Группа калибров "мeдиум" = 3 патрона• Группа калибров "магнум" = 3 патрона• Группа калибров "Jeffery" = 2 патрона• Калибр 10,3 x 60 R = однозарядный
ПРОВЕРЬТЕ:Красный квадрат не виден, рукоятка затвора в крайнем переднем положении. Карабин заряжен, боевая пружи-на расслабленна, затвор блокирован от произвольного открытия.
ВНИМАНИЕ:Извлечение магазина при закрытом затворе из взве-дённого оружия приведёт к сбросу ползуна взводителя в нижнее положение. Боевая пружина при этом будет расслаблена. Извлечение магазина при открытом за-творе из взведённого оружия оставит ползун взводите-ля в прежнем положении, боевая пружина останется в нагнетённом состоянии.
3.2. Блокировка магазина
Каждый карабин Blaser R8 со сменным магазином осна-щён блокировкой магазина, которая действует на кнопки извлечения магазина.
• При открытом затворе подвиньте кнопку блокировки магазина в заднее положение: видна буква "S". Кнопки извлечения магазина заблокированны.
• При включенной блокировке магазина, извлечение ма-газина невозможно. В данном случае карабин заряжа-ется как карабин R8 без сменного магазина.
• Блокировка магазина может быть включена и выклю-чена при открытом затворе кнопкой, которая находит-ся на дне сменного магазина.
4. Стрельба4.1. Стрельба и перезарядка
• Взведите карабин перемещением взводителя ударни-ка вперёд.
• Наведите оружие на цель, прицельтесь и произведите выстрел.
• Перезарядка: Переместите затвор рукояткой затвора в крайнее заднее положение (при этом происходит экстракция стрелянной гильзы), потом переместите затвор в крайнее переднее положение (при этом но-вый патрон заряжается в патронник).
УЧТИТЕ:Если при закрытии затвора рукоятка затвора не будет находитьсяв крайнем переднем положении, выстрел невозможен из соображений безопасности.
ВНИМАНИЕ:Если взводитель ударника находится в переднем по-ложении, ударник становится на боевой взвод при ка-ждом цикле перезарядки. При прекращении стрельбы карабин следует немедленно снять с боевого взвода перемещением взводителя ударника назад.
89
ВНИМАНИЕ:Взводите карабин только непосредственно перед вы-стрелом. При несостоявшемся выстреле следует снять карабин с боевого взвода. Если после выстрела Вы перезарядили карабин, и выстрeл не нужен, так же сле-дует снять карабин с боевого взвода.
4.2. Блок УСМ Atzl "матчевыйохотничий"
УСМ Atzl "матчевый-охотничий" позволяет выбрать усилие спуска между лёгким, "спортивным" и более тя-жёлым, "охотничьим". Выбор усилия спуска осуществля-ется без инструмента посредством переключателя на раме магазина при извлечённом из ствольной коробки магазине (Рис. 4.2.1). Кроме переключателя, необходим специальный блок УСМ в ствольной коробке (Рис. 4.2.2). Установка блока УСМ Atzl "матчевыйохотничий" возмож-на только на фирме Blaser в Isny.
Если у патронов в калибре .375 Blaser Mag., .375 H&H Mag., .416 Rem. Mag. и .458 Lott максимальная длина патрона (L6) превышает размер в 90,5мм, эти патроны несовместимы с магазином УСМ Atzl "матчевый-охот-ничий".
Принцип работы:Посредством переключателя можно выбрать одно из двух усилий:• Позиция "матч" : 250 г / 0.55 м• Позиция "охота" : 650 г / 1.43 м
УЧТИТЕ:Магазин от УСМ Atzl "матчевый-охотничий" можно без ограничений применять в любом R8 со стандартным блоком УСМ. Усилие спуска будет то, которое задано стандартным блоком УСМ. Переключатель в этом слу-чае не работает. Применение стандартного магазина в ствольной коробке с УСМ Atzl "матчевый-охотничий" не-возможно, магазин не защёлкнется в ствольной коробке.
ВНИМАНИЕ:Спуск Atzl "матчевый-охотничий" очень чувствителен в положении "матч" из-за низкого усилия. Особенно пе-ремещение спуска вперёд (как при шнеллере) и резкое отпускание спуска приведёт к несанкционированному выстрелу. Этого не стоит делать ни в коем случае! При контакте пальца со спуском, а так же при общем обра-
щении с взведённым и заряжённым оружием следует особенно следить за безопасностью!
ВНИМАНИЕ:Карабин Blaser R8 оснащён высокоточным спуском. Его настройка производится только на фирме Blaser. Ни в коем случае не пытайтесь самостоятельно изменить ха-рактеристику спуска. Регулярно проверяйте лёгкость хо-да спускового крючка при разряженном и невзведённом карабине. Загустевшее масло и сильное загрязнение могут привести к задержкам при стрельбе. Никогда не смазывайте спусковой механизм.
Рис. 4.2.2.
Рис. 4.2.1.
f Переключатель на
f Специальный блок УСМ в ствольной коробке
русский
90
5. Разряжание 6. Снятие с Установка затвора
5.1. Разряжание
• Снимите карабин с боевого взвода нажатием большо-го пальца на клавишу взводителя ударника и дайте ему отойти назад.
• Откройте затвор и отведите его в крайнее заднее поло-жение (см. пункт 2.4.), при этом патрон будет удалён из патронника и выброшен из ствольной коробки.
R8 со сменным магазином:• Извлеките сменный магазин из ствольной коробки
нажатием на кнопки извлечения магазина. Патроны, оставшиеся в вставке магазина удалите движением их вперёд, пока они не покинут губки магазина.
R8 без сменного магазина: • Патроны, оставшиеся в вставке магазина удалите дви-
жением их вперёд, пока они не покинут губки магази-на, затем удалите их из ствольной коробки.
• Проверьте наличие отсутствия патронов в магазине и патроннике.
6.1. Снятие затвора
• Снять оружие с боевого взвода, разрядить.• Откройте затвор и переместите его в крайнее заднее
положение.• Нажмите кнопку останова затвора и вытяните затвор
на его направляющих из ствольной коробки движе-нием назад.
У магазинных вставок следующих калибров: .222 Rem., .223 Rem., .22-250, .243 Win., 6,5x55, 6,5x57, 7x57, 7,5x55, .308 Win. и 8x57 IS имеется свой останов затвора, ко-торый встроен за правой губкой магазина. Для извле-чения затвора у карабина в одном из вышеуказанных калибров:
• Нажмите правую губку магазина внутрь, при этом оста-нов затвора вставки магазина будет отключен.
• Отодвиньте затвор назад до останова затвора на ствольной коробке.
• Отодвиньте затвор назад до останова затвора на ствольной коробке.
6.2. Установка затвора
• Утопите вставку магазина в ствольной коробке и удер-живайте его в этом положении.
• Установите затвор в задней части ствольной коробки, тщательно направив начало направляющих шин за-твора параллельно пазам ствольной коробки.
• Установите затвор в ствольной коробке.
91
7. Замена ствола
Существуют 6 групп калибров (см. пункт 13). При замене ствола из одной группы калибров в другую так же следу-ет заменить личинку затвора на соответствующую этой группе калибров. Приравнение к подходящим калибрам находится в таблице на пункт 130. Стволы и личинки затворов так же имеют маркировку группы калибров. При замене ствола/ сборки карабина эти маркировки должны совпадать.
Внутри определённой группы калибров замена стволов возможна без замены личинки затвора.
Группы калибров:Мини маркировка MIСтандард маркировка STMeдиум маркировка MEМагнум маркировка MAJeffery маркировка JE10,3 x 60 R маркировка CH
При замене ствола следите за тем, чтоб вствка магази-на соответствовала калибру ствола. Обозначение кали-бров находится сбоку на вставке магазина (см. пункт 7.2).
УЧТИТЕ: К стволу в калибре 10,3x60 R прилагается магазинная вставка для однозарядного карабина. Магазин в ком-плект не входит.
7.1. Замена ствола
• Снять оружие с боевого взвода, разрядить.• Открыть и извлечь затвор.• Открутить обе гайки крепления ствола шестгранным
ключом (SW5), они остаются в ствольной коробке.• Извлеките ствол из ствольной коробки.• Вставьте сменный ствол в ствольную коробку.• С помощью шестигранного ключа (SW5) затяниете обе
гайки крепления ствола.
R8 со сменным магазином:• Вставьте вставку магазина соответствующую калибру
ствола сверху в сменный магазин и утопите его в ствольной коробке (см. пункт 7.2.).
R8 без сменного магазина:• Извлеките вставку магазина (возможно придётся снять
оптический прицел, см. пункт 12.2.).• Вставьте вставку магазина, которая соответствует ка-
либру сменного ствола, сверху в ствольную коробку.• Убедитесь в том, что маркировка группы калибров на-
ходящаяся на личинке затвора ("MI", "ST", "ME", "MA", "JE", "CH" см. пункт 7 и схему 7.1.) соответствует груп-пе калибров сменного ствола.
• Если понадобится заменить личинку затвора, см. пункт 8.
УЧТИТЕ:Следите за чистотой постели ствола! Наличие масла или оружейной смазки между стволом и постелью ство-ла приведёт к ухудшению кучности Вашего карабина.
русский
92
8. Замена личинки затвора
7.2. Замена вставки магазина
R8 со сменным магазином:• Откройте затвор.• Извлеките патрон из патронника.• Извлеките и разрядите сменный магазин.• Подцепите указательным или средним пальцем пода-
ватель вставки магазина, вдавите большим пальцем левую губку магазина внутрь и извлеките магазинную вставку вверх.
• Вставьте вставку магазина соответствующую калибру ствола сверху в сменный магазин.
R8 без сменного магазина:• Снять оружие с боевого взвода, разрядить.• Снимите затвор.• Извлеките вставку магазина указательным пальцем.• Вставьте вставку магазина, которая соответствует ка-
либру сменного ствола, сверху в ствольную коробку.
8.1. Извлечение личинки затвора
Процесс замены личинки Вам покажет Ваш дилер или оружейник.• Снять оружие с боевого взвода, разрядить.• Откройте и извлеките затвор.• Положите затвор нижней стороной вверх на плоскую
поверхность.• Отожмите фиксатор личинки затвора налево подходя-
щим инструментом и поднимите его вверх.• Поверните личинку затвора в четверть оборота против
часовой стрелки и вытяните её вперёд.
8.2. Установка личинки затвора
• Откиньте фиксатор личинки затвора до упора вверх.• Вставьте личинку затвора в затвор, надев её на бо-
ёк, до упора. Поверните личинку затвора на четверть оборота по часовой стрелке, тем самым фиксируя её в затворе (см. рис. 8.2).
• Установите личинку затвора в затворе так, чтобы фик-сатор личинки затвора вошел в свой паз.
УЧТИТЕ: Для облегчения установки личинки затвора при поворо-те, следует легонько двигать рукояткой затвора.
• Фиксатор личинки затвора повернуть и установить или защёлкнуть в затворе.
93
9. Демонтаж/смена цевья/ цевья Stutzen
Карабин Blaser R8 в модификациях Semi Weight, Safari и Jagdmatch обладает цевьём с расширенной вырезкой под ствол. При установке стволов Semi Weight, Safari или Jagdmatch в стандартную модификацию R8 нужно заменить цевьё на подходящее к контуру ствола.
9.1. Демонтаж цевья
• При снятом стволе открутите крепёжный винт цевья длинным ключом SW5 и отсоедините цевьё от стволь-ной коробки.
9.2. Установка цевья
• Установите цевьё на ствольной коробке и затяните крепёжный винт цевья.
ВНИМАНИЕ:Если фиксатор личинки затвора закрыт не до конца, то из боковой направляющей выглядывает сигнальный штифт. Затвор можно установить в ствольной коробке только тогда, когда фиксатор личинки затвора закрыт до конца и сигнальный штифт не мешает установке затво-ра в ствольную коробку.
УЧТИТЕ:Личинки затвора "для левшей" обозначены буквой "L" под маркировкой группы калибров.
ВНИМАНИЕ:Цанга и втулка распорки соединенны вместе с личинкой затвора посредством заклёпки и представляют собой одно целое. Удалять заклёпку и разбирать личинку за-твора на составляющие части строжайше запрещенно! Выстрел с одной только ли чинкой затвора, без цанги и распорной втулки приведёт к разрыву затвора и по-влечёт за собой смерть стрелка!
русский
94
9.3. R8 Professional Success Stutzen
Модель R8 Stutzen доступна с двумя разными длинами ствола (52 см и 58 см), а так же с двумя разными по толщине контурами ствола (стандарт 17 мм и семи вэйт 19 мм у дульного среза).
Вариант цевья Stutzen Длина / Контур стволаВариант 1 520 мм / 17 мм
Вариант 2 520 мм / 19 мм
Вариант 3 580 мм / 17 мм
Вариант 4 580 мм / 19 мм
9.4. Замена ствола
Снятие:• Снять оружие с боевого взвода, разрядить.• Открыть и извлечь затвор.• Открутить обе гайки крепления ствола шестгранным
ключом (SW5), они остаются в ствольной коробке.• Поднять ствол в районе патронника и сдвинуть вперёд
(Рис. 9.2).
УЧТИТЕ:Установленные в передней части цевья Stutzen сильные магниты обеспечивают одинаковое прилегание цевья к стволу. Извлечь ствол проще, если поднять его с по-стели ствола в районе патронника и выдвинуть вперёд.
Установка:ПРОВЕРЬТЕ:Длина и диаметр цевья должны совпадать с параме-трами ствола.
• Установите ствол на постель ствола (Рис. 9.3).• При помощи ключа (SW5) затяните гайки крепления
ствола от руки.
9.5. Переделка модели R8 Professional Success в R8 Professional Success
Stutzen
• Снять оружие с боевого взвода, разрядить.• Открыть и извлечь затвор.• Открутить обе гайки крепления ствола шестгранным
ключом (SW5), они остаются в ствольной коробке.• Снять ствол со ствольной коробки.• Оба винта крепления оконцовки цевья (Рис. 9.4) откру-
тить шестигранным ключом (SW5) и извлечь вместе с шайбами.
УЧТИТЕ: Не забудьте снять и шайбы (Рис. 9.4a).
• Оконцовку цевья откинуть вниз и снять. Вставить цевьё Stutzen и поднять вверх.
• Вкрутить оба винта крепления вместе с шайбами (Рис. 9.5).
95
ВНИМАНИЕ:Постоянное магнитное поле способно уничтожить дан-ные, которые хранятся на магнитных носителях (дис-кеты, винчестеры, флэшки, кредитные и банковские карточки), а так же неисправимо повредить сам носи-тель. Поэтому сильные постоянные магниты не должны находится в близости таких носителей данных.
УЧТИТЕ:Карабин R8 Stutzen со стволом и просто ложа R8 Stutzen без ствола были проверены институтом TÜV Süd по соответствию с „Packing Instruction 953 for UN2807 Magnatized Material“. Оружие со стволом, равно как и просто ложа без ствола, не являются магнитизирован-ным материалом по требованиям „UN2807 Magnatized Material“ и могут без опасений перевозиться в пассажир-ских и грузовых самолётах.
УЧТИТЕ:Чтоб исключить какое-либо влияние на кучность боя и для обеспечения нормального функционирования ору-жия, обязательно следите за следующими пунктами:• Цевьё Stutzen должно быть правильно установлено и
прикручено к ложе.• Обратите внимание на чистую постель ствола!• Следите за тем, чтобы контактные плоскости цевья
и ствольной коробки были чистыми! Масло между стволом и ствольной коробкой негативно влияет на кучность стрельбы!
ВНИМАНИЕ:В кончике цевья находится сильный постоянный магнит, фиксирующий цевьё на стволе (Рис. 9.6). Магнитное поле постоянного магнита может повлиять на функцию кардиального имплантата (электрокардиостимулято-ра). Поэтому нельзя конец цевья помещать в непосред-ственную близость такого устройства.
Соблюдайте минимальное расстояние в 5 см до кончика цевья!
русский
96
11. Установка оптического прицела
Карабин с продольно-скользящим затвором Blaser R8 оснащён базами крепления для седельного кронштейна Blaser. Мы исходим из того, что Ваш оптический прицел был правильно установлен на кронштейн Вашим ору-жейником.
11.1. Установка оптического прицела
• Откройте лапки крепёжных винтов и поверните боль-шим пальцем оба винта до упора вперёд/наверх.
• Возьмите прицел в руку таким образом, что бы боль-шой палец доставал до передней лапки крепёжного винта.
• Охватите левой рукой цевьё карабина, приклад можно упереть в бедро.
• Установите круглые цапфы кронштейна в овальных выемках под цапфы в правой верхней стенке ствола, и осторожно опустите левую сторону кронштейна на ствол.
• Поверните сначала передний, потом задний крепёж-ный винт движением назад/вниз до упора. Если этот процесс требует больших усилий или наоборот осту-ществляется чересчур легко, требуется правильно настроить затяжку крепёжных винтов. Идеальное усилие закрытия крепёжных винтов примерно соот-ветствует усилию взвода ударника/ шпаншибера.
• Закройте обе лапки крепёжных винтов.
ВНИМАНИЕ:Следите за тем, что бы соприкасающиеся поверхности были чистыми и обезжиренными!
10. Открытый прицел
10.1. Мушка с регулировкой по высоте
• Вставьте шестигранный ключ SW1,3 сверху в отвер-стие на мушке:
• Если мушкувыкрутить = СТП внизвкрутить = СТП вверх
10.2. Целик с регулировкой по горизонту
• Целик имеет с обоих сторон отверстия для шестигран-ного ключика SW1,3.
• При попадании слева от точки прицеливания: Целик сдвинуть вправо. Для этого ослабить левый винтик и затянуть правый винтик.
• При попадании слева от точки прицеливания: Целик сдвинуть вправо. Для этого ослабить левый винтик и затянуть правый винтик.
10.3. Открытые прицельные приспособления Safari с регулировкой по вертикали и горизонтали
С июня 2014 г прицелы Safari от Blaser поставляются с механизмом для регулировки. Регулировка выполняется с помощью шестигранного ключа SW2 так же, как и в случае с простым открытым прицелом (см. выше).Прицелы Safari, произведенные до июня 2014 года, не-регулируемые. Они имеют стандартную высоту мушки в 6мм и пристреливаются на расстояние в 30м. Мушки с другой высотой и другие целики предлагаются в каче-стве опции за дополнительную плату.
97
11. Установка оптического прицела
11.2. Снятие оптического прицела
• Охватите левой рукой цевьё карабина, приклад можно упереть в бедро.
• Откройте обе лапки крепёжных винтов.• Сначала поверните задний крепёжный винт до упора
вперёд/наверх.• Охватите правой рукой оптический прицел и придер-
живайте его.• Поверните передний крепёжный винт до упора вперёд/
вверх большим пальцем.• Снимите прицел движением вверх/ вправо.
ВНИМАНИЕ: При недостаточно большом расстоянии от окуляра до глаза, а так же при неправильной вкладке приклада в плечо при стрельбе из больших калибров не исключена возможность травмы глазной впадины или надбровной дуги. Поэтому при стрельбе из больших калибров уделите особое внимание расстоянию от окуляра до глаза и пра-вильной вкладке приклада.
12. Установка оптического прицела (США)
12.1. Установка оптического прицела
• Отвинтите оба винта с головкой под шестигранный ключ SW1/8" дюйма на несколько оборотов.
• Охватите правой рукой оптический прицел.• Охватите левой рукой цевьё карабина, приклад можно
упереть в бедро.• Установите круглые цапфы кронштейна в овальных
выемках под цапфы в правой верхней стенке ствола, и осторожно опустите левую сторону кронштейна на ствол.
• Затяните оба крепёжных винта в меру туго шестигран-ным ключом SW1/8".
12.2. Снятие оптического прицела
• Охватите левой рукой цевьё карабина, приклад можно упереть в бедро.
• Отвинтите оба крепёжных винта шестигранным клю-чом SW1/8" на несколько оборотов.
• Снимите оптический прицел.
русский
98
Мини "MI":
.222 Rem. .223 Rem.
.204 Ruger
Стандард "ST":
.22-250 7x64
.243 Win. .308 Win.
6XC .30-06
6,5x55 SE 8x57 IS
6,5x57 8,5x63
6,5x65 RWS 9,3×57
.270 Win. 9,3x62
Медиум "ME":6,5x68 8x68 S
7,5x55 Swiss
Магнум "MA":
.257 Weath. Mag. .300 WSM
.270 Weath. Mag. .338 Blaser Mag.
.270 WSM .338 Win. Mag.
7 mm Blaser Mag. .375 Blaser Mag.*
7 mm Rem. Mag. .375 H & H Mag.*
.300 Blaser Mag. .416 Rem. Mag.*
.300 Win. Mag. .458 Lott*
.300 Weath. Mag. .458 Win. Mag.
Jeffery "JE":
.500 Jeffery
Швейцарский "CH":
10,3x60 R
* Эти калибры невозможны в сочетании с матчевым спуском УСМ Atzl "матчевый-охотничий"
14. Кейс
В фирменном кейсе из специального пластикa ABS с тремя замками Ваш карабин R8 всегда надёжно размещён для транспортировки.
Кейс BДля карабина Blaser R8 с установленным цевьём и опти-ческим прицелом.Так же подходит для моделей оружия с откидными стволами.Габаритный размер: 78x26x9 см
Кейс CДля всех карабинов и комбинированных ру-жей фирмы Blaser с установленным цевьём. С дополнительным отделением для смен-ного ствола и второго оптического прицела. Габаритный размер: 84x45x11 см
13. Группы калибров
Пожалуйста учтите, что мы не можем гарантировать постоянное наличие всех указанных калибров на складе в момент заказа.
99
15. Корпус магазина R8 .338 Lapua Magnum
Общаяя ИнформацияСпециально изготовленный корпус магазина обеспе-чивает досылание патронов при максимальной длине (COL, L6 по стандартам CIP) и позволяет применять лю-бимый охотниками и стрелками на дальние дистанции калибр .338 Lapua Magnum.
Принцип РаботыНовый корпус магазина может быть использован во всех карабинах Blaser R8 Professional Success.
ВНИМАНИЕ:Затвор (личина затвора), ствол и корпус магазина долж-ны соответствовать применяемуму калибру .338 Lapua Magnum. Обозначение находится на головке затвора и на стволе возле серийного номера на казённой ча-сти. Для однозначной идентификации демпфирующая вставка в передней части корпуса магазина окрашена в оранжевый цвет и вклеена в корпус, сам корпус магази-на маркирован (см. изображение 1)
Технические данные
Корпус магазина .338 LAPUAДлина патрона: до максимальной, положенной по CIP длине патронаКорпус магазина для УСМ ATZL .338 LAPUAДлина патрона: В отличии от CIP, максимальная длина патрона 92,2мм
УходСменный магазин и корпус магазина с встроенным спу-ском должны содержаться в чистоте. Не допускать попа-дания в них инородных тел.
» Оптимизированная демпфирующая вставка, оранжевого цвета, вклеена.
» Маркировка калибра: (только .338 LAPUA Mag.)
русский
100
16. Уход за оружием
Для ухода за оружием следует применять лишь для это-го предназначенные средства.
Ствол:Стволы фирмы Blaser изготавливаются из легирован-ной стали, которая отвечает строжайшим требованиям по чистоте, однородности и механическим свойствам, особенно в высокодинамичном спектре нагрузок. Каче-ство ствольного материала постоянно контролируется и документируетсяпроизвопроизводителем, а так же и нашим ствольным цехом.
Ствол снаружи:Поверхность ствола снаружи азотирована в плазме и заворонена, что является очень хорошей защитой от царапин и – при правильном уходе – от коррозии, но 100%-ная защита невозможна. Мы рекомендуем содер-жать поверхность ствола чистой и регулярно наносить тонкий защитный слой подходящего оружейного масла. Особенно если ствол намок под дождём или «вспотел» в синтетическом чехле, его нужно протереть насухо и нанести тонкий защитный слой подходящего оружейного масла.
Ствол внутри:Внутренняя поверхность ствола образуется при хо-лодной ковке, и обладает отличными показателями по качеству поверхности. Гладкая поверхность улучшает защиту от коррозии, но это ни в коем случае не заме-няет регулярную чистку и уход. Мы настоятельно реко-мендуем обезжиривать патронник и канал ствола перед стрельбой во избежание «отрывов» или смещений СТП.После использования оружия ствол надлежить почи-стить и законсервировать, потому что несгоревшие частицы пороха в стволе и в патроннике обладают ги-гроскопическими свойствами и собирают влагу внутри ствола. Особенный уход нужен патроннику: С помощью гильз в патронник может попасть пот с ладоней стрелка, который при неблагоприятных условиях может действо-вать агрессивно и этим привести к коррозии.При обильных наслоениях в канале ствола рекоменду-ется химическая чистка. После химической чистки нужно обязательно протереть ствол и патронник насухо и на-нести тонкий защитный слой подходящего оружейного масла.
ВНИМАНИЕ: Ни в коем случае не храните оружие с заклеенным дульным срезом или с надетым защитным чехольчи-ком дульного среза! Обязательно соблюдайте указания производителя чистящих средств!
Металлические детали:Держите металлические детали в чистоте и слегка смазывайте маслом.Масло для дерева не годится для ухода за металли-ческими деталями!
Сменный магазин:Регулярно чистите его и следите, что бы в него не попа-дали посторонние предметы!
Ложа:Все деревянные детали оружия фирмы Blaser Jagdwaffen обработаны шлифовкой с маслом. Мы сове-туем регулярно обрабатывать их средствами для ухода за деревянными деталями оружия.Оружейное масло не годится для ухода за ложей!
Рекомендации по уходу для карабина Professional Success с кожаными вставками:Кожаные вставки карабина R8 Professional Success об-работаны специальным способом и не требуют частой чистки. Для ухода за ними пользуйтесь специальным средством для ухода за кожанными изделиями „Blaser Lederplege“.
Оптика:Смотрите инструкцию изготовителя оптики.
ACHTUNG:При уходе за охотничьим оружием нужно следить за тем, что бы масло или оружейная смазка не попадали в ударно-спусковой механизм. Нередко затвердевшее масло может привести к отказу или неправильному функционированию ударно-спускового механизма в са-мый неподходящий момент. Следите затем, что бы Ва-ше охотничье оружие перед каждым охотным сезоном проходило технический осмотр у Вашего оружейника. Оружие, как и любая техническая система нуждается в регулярном контроле работоспособности.
101
17. Гарантийные условия
кучность нашего оружия.Рекламации по поводу неудовлетворительной кучности должны быть заявлены в письменом виде в течении 20 дней с даты покупки. В случае рекламации мы в праве пе-ренаправить оружие на независимую экспертизу (DEVA или Staatliches Beschussamt). В случае подтверждения превосходной кучности данной экспертизой, фирма-про-изводитель в праве потребовать компенсацию расходов на экспертизу у клиента.
3. Объём гарантии
Гарантийный ремонт не подразумевает продление га-рантийного срока для оружия или заменённых деталей. Гарантийный срок на установленные запасные части заканчивается с гарантией на весь карабин.
4. Исключения
Гарантия исключена в следующих случаях:• Дефекты в следствии обычного износа, при не соблю-
дении данного руководства по эксплуатации, при ис-пользовании оружия не надлежащим образом, а так же при наличии механических повреждений любого вида.
• Дефекты в следствии воздействия окружающей среды и форс-мажорных обстоятельств.
• Ремонт, обработка или изменения оружия посторон-ними лицами.
• Использование самоснаряжённых патронов (рилоуд) или патронов, несоответствующих стандарту CIP.
• Исполнение воронения посторонними лицами.
Гарантия не распространяется на оптические прицелы и крепления для оптики других производителей кроме как Blaser Jagdwaffen. Дальнейшие претензии, особенно ка-сающиеся повреждений вне оружия и последствий этих повреждений, не принимаются.
1. Гарантия производителя
Гарантия фирмы Blaser Jagdwaffen GmbH действитель-на в добавок к гарантийным обязательствам торговой компании в том случае, если прилагаемый к каждой мо-дели оружия фирмы Blaser паспорт, будет получен в за-полненом виде производителем в течении десяти дней с даты покупки. Гарантия действительна только для первичного покупателя с ПМЖ в стране приобретения.
Гарантия распостраняется только на металлические и пластмассовые детали оружия, а так же на оригиналь-ный седельный кронштейн фирмы Blaser, но не на оп-тический прицел. Деревянные детали оружия подлежат особому уходу и, как природный материал, подвержен-ны воздействию времени, поэтому арантия на них не распостраняется.
Гарантийный срок длительностью в десять лет начина-ется со дня продажи и распостраняется на все поломки и неисправности оружия, которые основанны на дефектах металла и ошибках при изготовлении. При рекламациях в таком случае изготовитель берёт расходы на запчасти и рабочее время на себя. Для проведения гарантийного ремонта необходимо доставить оружие к производите-лю, либо к цертифицированному производителем ору-жейнику.
Ответственность и расходы на пересылку несёт клиент. Размеры гарантийного обслуживания установляются производителем. Это может быть ремонт или замена неисправных деталей, которые переходят в имущество фирмы.
2. Гарантия кучности
Кучность оружия зависит от многих факторов. Важней-шим фактором являются боеприпасы. Не каждый ствол стреляет одинаково хорошо всеми типами боеприпасов, они могут сильно отличаться. Выбор оптического прице-ла и его крепления тоже влияют на результаты стрельбы, так же как и параллакс, люфтящие прицельные сетки, дефекты механизмов горизонтальных и вертикальных поправок и несовершенные кронштейны. Поэтому реко-мендуется использование оптических прицелов высше-го класса, а так же их установление специалистами. Так же следует подобрать подходящий для Вашего оружия боеприпас методом отстрела нескольких сортов.При оптимальном сочетании боеприпасов, оптического прицела и кронштейна мы гарантируем превосходную
07-2015 производитель сохраняет право на тех. изменения.
русский
1.1. 1.1.
1.1.
1.1.
1.1.
2.1.
2.2.
3.1.
1.1.
2.1.
2.3.
2.4.
3.1.
2 mm
3.1.
3.2.
5.1.
8.1.
7.2.
6.1.
7.2.
7.1.
ST ST
8.1.
8.2.
8.2.
8.2.
9.1.
2
1
2
1
9.2.
9.3.
9.4.
11.1.
11.1.
9.4a.
9.5.
9.6.
Blaser Jagdwaffen GmbHZiegelstadel 188316 Isny Germany C9900010 | 07/2015