Belajar Structural Detailing

5/28/2018 Belajar Structural Detailing

1/41

AutoCADStructuralDetailing2011

GettingStartedwithAutoCAD

StructuralDetailing,

Reinforcementmodule


2/41

2010 Autodesk, Inc. All Rights Reserved. Except as otherwise permitted by Autodesk, Inc., thispublication, or parts thereof, may not be reproduced in any form, by any method, for any purpose.

Certain materials included in this publication are reprinted with the permission of the copyrightholder.

DisclaimerTHIS PUBLICATION AND THE INFORMATION CONTAINED HEREIN IS MADE AVAILABLEBY AUTODESK, INC. AS IS. AUTODESK, INC. DISCLAIMS ALL WARRANTIES, EITHEREXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIESOF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE REGARDING THESEMATERIALS.

TrademarksThe following are registered trademarks of Autodesk, Inc., in the USA and/or other countries:Autodesk Robot Structural Analysis, Autodesk Concrete Building Structures, Spreadsheet Calculator, ATC, AutoCAD,Autodesk, Autodesk Inventor, Autodesk (logo), Buzzsaw,Design Web Format, DWF, ViewCube, SteeringWheels, and Autodesk Revit.All other brand names, product names or trademarks belong to their respective holders.

Third Party Software Program CreditsACIS Copyright 1989-2001 Spatial Corp. Portions Copyright 2002 Autodesk, Inc.Copyright 1997 Microsoft Corporation. All rights reserved.

International CorrectSpell Spelling Correction System 1995 by Lernout & Hauspie SpeechProducts, N.V. All rights reserved.InstallShield 3.0. Copyright 1997 InstallShield Software Corporation. All rights reserved.PANTONE and other Pantone, Inc. trademarks are the property of Pantone, Inc. Pantone, Inc.,2002.Portions Copyright 1991-1996 Arthur D. Applegate. All rights reserved.Portions relating to JPEG Copyright 1991-1998 Thomas G. Lane. A ll rights reserved. Portions ofthis software are based on the work of the Independent JPEG Group.Portions relating to TIFF Copyright 1997-1998 Sam Leffler. Copyright 1991-1997 SiliconGraphics, Inc. All rights reserved.

Government UseUse, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth inFAR 12.212 (Commercial Computer Software-Restricted Rights) and DFAR 227.7202 (Rights inTechnical Data and Computer Software), as applicable.


3/41

Contents

GettingStartedGuide................................................................................................................................... 1

GettingStarted

..........................................................................................................................................

1

ExploringtheUserInterface...................................................................................................................... 1

ObjectInspector........................................................................................................................................ 3

ProgramPreferences................................................................................................................................. 5

TypesofReinforcement............................................................................................................................ 6

RulesforPositioningaReinforcingBarinaDrawing................................................................................ 6

DescriptionsofReinforcement.................................................................................................................. 7

Workflow................................................................................................................................................... 7

CreatingaReinforcedConcreteStructure................................................................................................ 8

CreatingaTemplate.............................................................................................................................. 8

DefiningFormworkofaBeam............................................................................................................. 12

AddingAxes......................................................................................................................................... 14

AddingaStirrupintheCrossSection.................................................................................................. 15

AddingaStirrupintheElevationView................................................................................................ 17

DefiningMainBars.............................................................................................................................. 20

CreatingCross

sections

.......................................................................................................................

24

CreatingaColumnandaSpreadFooting............................................................................................ 30

AddingMaterialTakeoffs.................................................................................................................... 34

DefinitionofViews.............................................................................................................................. 36

CreatingSheetsandAddingViews...................................................................................................... 37


4/41

GettingStartedGuide

ThankyouforchoosingAutoCADStructuralDetailing.TheReinforcementmoduleisfor

automatedreinforcement

definition

and

the

generation

of

shop

drawings

for

all

types

of

structuralconcretemembers.Theexercisesinthisguidegiveyouastartingpointfor

preparationofyourownprojects.

GettingStarted

Beforebeginningtheexercises,youneedtoinstallandregisterthesoftware.

AutoCADStructuralDetailingsoftwarecomeswiththeAutoCADRevitStructure

Suite.This

software

is

available

for

32

bit

and

64

bit

Windows

systems.

ExploringtheUserInterface

OpenAutoCADStructuralDetailing,Reinforcementmodule,andtakeaminuteto

viewthedifferentareasoftheinterface.

Ribbon

At the topof the interface is the standardMicrosoftWindowselement ribbon.

The ribbon isanelementof theuser interfacewhich replaces the traditionalmenu

and toolbars and allows easymanaging and adjusting theworkspace. The ribbon

consistsof severalpanels,groupedon tabs thatarenamedby taskor subject.The

ribbonpanelsincludemanyAutoCADStructuralDetailingcommandsthathavebeen

ontoolbarsandindialogssofar,suchasicons,dropdownlists,sliders,textfieldsand

otherelementscharacteristicofagiventab.

NOTEItispossibletoswitchbetweenworkspaces(suchastheclassicworkspacewithoutthe

ribbon).Todoitfollowoneofthegivenmethods:

1ClickManageCustomization (UserInterface)intheCustomizeUserInterfacedialogboxselecttheCustomizetabandinASD/WorkspacesselectASD

ReinforcementClassicrightclickselectSetcurrentfromthecontextmenu

clickApply

2Click (atthebottomrightcornerofthescreen)andselectASDReinforcementClassic.

1


5/41

ObjectInspector

Inspectorletsyoumanageelements(objects)includedinaprojectthatwascreatedin

AutoCADStructuralDetailing.

Layout/ModelTabBar

AtthebottomofthedrawingareaisthestandardAutoCADModel/LayoutTabBar.

Thereare2additionaltabsdefinedEditionLayoutandTemplatesLayout.Onthe

EditionLayouttab,youcanmodifythedrawings(documents)generatedforthe

structureelementsorgroupofelements.TheTemplatesLayouttabdisplaysthe

printouttemplatesdefinedintheproject.

Ribbon

Model/DrawingAreaModel/LayoutTabBarObjectInspector

2


6/41

ObjectInspector

UsingtheInspector,youhavequickaccesstoprojectelementsfromeverystageof

work,whichhelpsyoumanageyourproject. Bydefault,theObjectInspectordialog

displayson

the

left

side

of

the

interface,

beside

the

drawing

area.

You

can

adjust

the

widthofthedialogtoleaveasmuchspaceaspossiblefordrawingthegraphicmodel.

OntheModeltabisalistofmodelelements(levels,groups,andelementsthatbelong

tothelevelsandgroups)thatdescribethedivisionofreinforcingbarsintostructural

elements(beams,columns,spreadfootings,andsoon).

ThePositionstabdisplaysalistofdefinedviewsthatcontainthename,scale,and

printoutlayoutnamefortheview.

3


7/41

ThePrintoutstabletsyoumanageprintoutsinAutoCADStructuralDetailing.It

displaysthelistofallprintoutsandtheassociatedviewsdefinedintheAutoCAD

StructuralDetailingproject.Theprintoutlistincludesallprintouts,eventhosethatdo

notcontainviews.

UsetheASDCentertabtocopysettingsandstylesbetweenprojects.

4


8/41

ProgramPreferences

Preferences

ThePreferences

are

located

in

AutoCADs

Options

dialog.

The

Structural

Detailing

tab

letsyouselectthedefaultstarttemplateandworkspacenamefortheReinforcement

module.Thesoftwareprovidesmanytemplatesthataredefinedforspecific

countries.

Jobpreferences

Thesepreferencesarerelatedtoaparticulartemplateandproject.Afteryouhave

startedworkingonaproject,itisnotpossibletochangeworkunits.Somesettings

(suchasdesigncodesanddatabases)arespecifiedonlyatthebeginningofthe

project,beforeyouaddelementsintomodelspace.

5


9/41

TypesofReinforcement

Usingthereinforcementmodule,youcancreaterebarorwirefabricforstructural

elementsofeverytypeandshape(frombeamstoadvanced,complicatedelements).

Thereare3waystodefinereinforcementofstructuralelements:

Manually Automatically,basedonmacrosforthegenerationofreinforcementandformworkoftypicalstructures.MacrosinAutoCADStructuralDetailinglet

yougeneratecompleteconcretereinforcementdrawings,togetherwithrebar

descriptionsandmaterialtakeoffs.

Usingdatafromexternalsoftware,byimportingandexportingfromAutodeskRobotStructuralAnalysisProfessionalsoftware,andbyexporting

reinforcementdatafromRevitStructuresoftware.

RulesforPositioningaReinforcingBarinaDrawing

Thesoftwaredeterminesthepositionofareinforcingbarinadrawingdependingon

thedirectioninwhichpointsaredefined.Theorientationofthereinforcingbaris

determinedbytheorderofthepointsinaclockwisedirection,inrelationtothe

externalpartofanobject.

6


10/41

DescriptionsofReinforcement

Afterreinforcementisdefined(barshape,reinforcementdistribution,wirefabric

distribution,andsoon),thesoftwareautomaticallyrunsanoptionthatsuggestsa

descriptionappropriate

for

the

reinforcement

type.

The

resulting

dialog

depends

on

thetypeofselectedreinforcementdescription.

EverytypeofdescriptionhastheActiveoption.Iftheoptionison,thenthe

reinforcementisdescribedandiscountedinthereinforcementtable.Whenthesame

reinforcementisdescribedtwice,theoptionshouldbeofftopreventdoublingthe

numberofreinforcingbarscalculatedwhenpreparingabartable.

Workflow

Thecreationofeverycompleteprojectisbasedon3stages:

Modeling youworkontheModeltab(modelspace)todefineformworks,reinforcement,andmaterialtakeoffs.

Viewsyouworkinmodelspacetodefineeachviewasasingleelementwithitsownscale.

PrintoutsyouworkinLayoutspacetopreparethefinalshopdrawings.Inthisstage,youworkwithviewsthatwerecreatedearlier.

Modeling

Views

Shopdrawings

7


11/41

CreatingaReinforcedConcreteStructure

Inthislesson,youwillcreateasimplereinforcedframeandmaterialtakeoffs.Youwill

alsocreateafinalshopdrawing.

CreatingaTemplate

InordertostartworkinginAutoCADStructuralDetailing,youneedtoselecta

template.Thetemplatefilecontainsinitial,predefinedsettingsoftheworking

parameters.Inthisexercise,youwillcreateatemplate.

1 Click New.2 IntheSelecttemplatedialog,selectRBCR044.dwt,andclickOpen.3 DefineanewBartablestyle:

ClickASD ReinforcementSettingsStyles reinforcement

tables.Alternatively(forASDReinforcementClassicworkspace),

clickReinforcementmenuReinforcementtableStyles

Reinforcementtables.

IntheReinforcementtables stylemanager,forTable,selectMAIN

bars,andthenclickNew.

OntheTabletaboftheDefinitionofnewreinforcementtablestyle

dialog,selectMAIN,andthenclearRevisionandselectBarsymbol.

8


12/41

Click .

SelectLENGTHS,andthenselectTotal(bar).

ForUnits,selectm(meter),andspecifytheaccuracyas2decimal

places(0.00).

VerifythatBarisselected,andspecifythesamesettings.

Click .

OntheSortinganddetailedoptionstab,underDescriptionofbar

symbol,selectSymbol:A,B,C.

Onthe

Options

tab,

select

Automatically

adjust

row

height.

ForListofstyles,enterMyBarTableStyleasthenameofthenew

style.

9


13/41

ClickOK.

IntheReinforcementtables stylemanagerdialog,forTablestyle,

selectMyBarTableStyle,andthenclickDefault.

Click

OK.

4 ChangeJobpreferences:ClickASD ReinforcementSettings (Jobpreferences).

Alternatively,clickReinforcementmenuJobpreferences.

IntheleftpaneoftheJobpreferencesdialog,selectBarsDisplay.

UnderBarshape,forEndofstraightbars(withouthooks),selectthe

secondoption.

Intheleftpane,selectCodes/Materials.

UnderReinforcingbars,forDatabase,click andselectbar_BS

8666_2000database.

UnderReinforcingbars,forSteelgradeRandT,changetheSymbol

to.

ClickOK.

10


14/41

5 Defineanaxisstyle:ClickASD ReinforcementSettingsGraphicelementsstyles.

Alternatively,clickReinforcementmenuGraphicelements

Styles graphicelements.

IntheStylesofsymbolsdialog,forSymbol,selectAxis,andthenclick

New.

IntheAxisdialog,underAxis,forColor,selectMagenta.

ForStylename,enterMyAxisStyle,andthenclickAdd.

IntheStylesofsymbolsdialog,forSymbolstyles,select

MyAxisStyle,andthenclickDefault.

ClickClose.

11


15/41

6 Savethetemplate:

Click Saveas.

For

File

name,

enter

MyTemplate.dwt,

and

click

Save.

IntheTemplateOptionsdialog,clickOK.

7 Setyourtemplateasadefault:ClickASD ReinforcementSettings (Preferences).

Alternatively,clickReinforcementmenuPreferences.

OntheStructuralDetailingtaboftheOptionsdialog,for

Reinforcement,clickSearch.

IntheOpendialog, selectMyTemplate.dwt,andclickOpen.

IntheOptionsdialog,clickOK.

Closetheprogram.

8 Proceedtothenextexercise,DefiningFormworkofaBeam.

DefiningFormwork

of

aBeam

Beforeyoubegindefiningreinforcementforabeam,youshoulddefineitsformwork.

TheformworkintheReinforcementmodulecanbecreatedusingMacrosorusing

AutoCADoptions.Inthisexercise,youaddtheformworkofthebeamintomodel

space.

1 StarttheReinforcementmoduleofAutoCADStructuralDetailing:

ClickASD

Start

(Reinforcement).

2 ClickASD StructureElementsStructureelements formwork(Beam).Alternatively,clickReinforcementmenuFormworksBeam.

3 IntheBeamdialog,forGeometrytab,specifyparametersofthebeamsformworkasshown.

12


16/41

4 IntheBeamdialog,forSectionstab,specifyparametersofthebeamsformworkasshown.

5 ClickOK.6 Inthedrawingarea,clicktospecifyaninsertionpoint.7 RemoveaxesatthebeamssupportbyusingAutoCADEraseoption.8 Modifyheightofbeamsupportto500mmbyusingAutoCADStretchoptionasshowninthedrawingbelow.

13


17/41

9 Proceedtothenextexercise,AddingAxes.

AddingAxes

Inthisexercise,youwilladd2axestothebeamformwork.

1 ClickASD ReinforcementGraphicelements (Insertaxis).Alternatively,clickReinforcementmenuGraphicelementsInsert

axis.

2 Onthecommandline,changetheaxisnumberto1.3 Insertthefirstaxisinthemiddleoftheleftbeamsupport:

Selectfirstpoint.

Selectsecondpoint.

4 Usingthesamemethod,addaxis2tothemiddleoftherightsupportbeam.

5 Proceedtothenextexercise,AddingaStirrupintheCrossSection.

14


18/41

Adding

a

Stirrup

in

the

Cross

Section

Inthisexercise,youlldefinestirrupsinthecrosssectionAAofbeamformwork.You

willdefinerebarshapeswiththeirdescriptions.

1 AddanauxiliarypointintheformworkcrosssectionAA:ClickHomeDrawMultiplePoints.Alternatively,clickDraw

menuPointMultiplePoint.

Clicktheupperrightcornerofthecrosssectionasthefirstpoint.

Onthecommandline,type@114,0,andthenpressEnter.

PressEsc.

2 Defineastirrup:ClickASD ReinforcementReinforcementdefinition

Reinforcementcrosssection.Alternatively,clickReinforcement

menuReinforcement crosssection.

IntheReinforcementcrosssectiondialog,click .

Specifyrebarparametersasshown.

15


19/41

ClickShapeparameters.

IntheReinforcingbarparametersdialog,specifystirrupparameters

asshown.

ClickOK.

IntheReinforcementcrosssectiondialog,selectamodeof

graphicalreinforcement

definition,

and

then

click

(Insert).

Inthedrawingarea,selecttheauxiliarypointyoudefined,choose

theproperorientationforthestirrup,andthenpressEnter.

IntheReinforcementdescriptiondialog,acceptthedefault

parameters,andclickOK.

Insertdescriptionofthestirrupbyselectingpointsinthemodel

area.

16


20/41

3 Mirrorthestirrup:SelectthestirrupwithdescriptionandclickHomeModify

(Mirror). Alternatively,clickModifymenuMirror.

Clickaboveandbelowthecrosssectionatthemidpointtospecify

thefirst

and

second

points

of

the

mirror

line.

4 Proceedtothenextexercise,AddingaStirrupintheElevationView.

AddingaStirrupintheElevationView

Inthisexercise,youlldefinestirrupsintheelevationviewofbeamformwork.Youwill

definerebardistributionwiththeirdescriptions.

1 ClickASD ReinforcementReinforcementdefinition(Reinforcementdistribution).Alternatively,click Reinforcementmenu

Reinforcementdistribution.

2 Inthedrawingarea,selectbothstirrupsinthecrosssection,andpressEnter.

17


21/41

3 IntheReinforcementdetailingdialog:ForDistributionTYPE,click (Linear).

ForDistribution

METHOD,

click

(Module).

ForViewingDIRECTION,click (projectiontoYaxis).

ClickOK.

4 Definedistributionintheelevationview:Inthedrawingarea,clickpoint1tospecifythedistributionstart

point.

Clickpoint2tospecifythedistributionendpoint.

Todefinethepositionofthefirstrebar,enter20onthecommand

line.

18


22/41

Todefinestirrupspacing,type7*170,where7isthenumberofstirrupsand170isthespacing.

Definethesecondstirrupspacingas5*250.

Right

click,

and

click

Mirror.

PressEnter.

NOTEAfterreinforcementisdefined(barshape,reinforcement

distribution,wirefabricdistribution,andsoon),thesoftware

automaticallyrunsanoptionthatsuggestsadescriptionappropriatefor

thereinforcementtype.Theresultingdialogdependsonthetypeof

selectedreinforcementdescription.

IntheReinforcementdescriptiondialog,acceptthedefault

parameters,andclickOK.

Inthemodelspace,selectthepointtodefinethelocationofthe

distributionline.

Clicktospecifythedescriptionlocation.

5 Modifythedefineddistribution:Selectthedistributionofstirrups,rightclick,andclickModify.

IntheModificationofreinforcementdistributiondialog,clickDelete,

andclickthestirrupinthemiddleofbeam.Thepropernumberof

stirrupsshouldbe2x25.

PressEsc,andthenclickOK.

19


23/41

7 Proceedtothenextexercise,DefiningMainBars.

DefiningMain

Bars

Inthisexercise,youlldefinelongitudinalreinforcementofbeamintheelevation

view.

1 Definethefirstlongitudinalrebarinelevationview(rebarnumber2):ClickASD ReinforcementReinforcementdefinition

(Reinforcementelevation).Alternatively,clickReinforcement

menu

Reinforcement

elevation.

IntheReinforcement elevationdialog,click .

Specifytherebarparametersasshown.

Click (Points).

20


24/41

Inthedrawingarea,clickpoint1tospecifythefirstbarattachmentpoint.

Clickpoint2tospecifythesecondbarattachmentpoint.

IntheReinforcementdescriptiondialog,clickOKtoadddescription

tothe

rebar

by

clicking

points

in

the

model

area.

2 Usingthesamemethod,defineanotherrebar(number3)withadiameterof16mm,andspecifyitslocationasshown.

21


25/41

IntheReinforcementdescriptiondialog,clickOK.

3 Definethelastrebarinelevationview:

ClickASD

Reinforcement

Reinforcement

definition

(Reinforcementelevation).Alternatively,clickReinforcement

menuReinforcementelevation.IntheReinforcement

elevationdialog,specifytherebarparametersasshown.

Click (Points).

Inthedrawingarea,clickpoint1asshowntospecifythebar

attachmentlocation.

22


26/41

Rightclick,andclickMirror.

Rightclick,andclickSide.

Clickpoints2and3tospecifyadditionalcharacteristicpoints.

NOTEYou

can

add

auxiliary

characteristic

points

to

formwork

using

the

AutoCADDrawoption.

Onthecommandline,typeStochangethesideofacover.

Clickpoints4and5tospecifyadditionalcharacteristicpoints.

IntheReinforcementdescriptiondialog,clickOK.

Descriptionisaddedtotherebar.

NOTEWhenyoudefinebarsfromthedatabase,youselectoneofthem

fromtheavailableshapelist.Youthendefinesuccessivebarsegmentsby

selectingthenextbarscharacteristicpointsintheschematicdrawing(or

bytypingdimensionsofindividualsegments).

4 Proceedtothenextexercise,CreatingCrosssections.

23


27/41

CreatingCrosssections

Afteryouhavefinishedplacingbeamrebarintheelevationviewandhavedefined

theirshapes,youcalculatethenumberoflongitudinal(main)rebarsinthebeam.

Inthisexercise,youllcreate3crosssectionsincharacteristicpointsofthebeam.

1 ModifyexistingcrosssectionAA:ClickASD ReinforcementReinforcementdefinition

(Reinforcementpoint).Alternatively,clickReinforcementmenu

Reinforcement point.

Inthedrawingarea,selectrebarnumber3(oritsdescription).

IntheReinforcementpointdialog,click .

UnderDistributionparameters,selectEnd,andthenclick

(Segment).

Inthedrawingarea,selectthebottomsegmentsofeachstirrup,

rightclick,andthenpressEnter.

IntheReinforcement pointdialog,clickOK.

IntheReinforcementdescriptiondialog,specifytheparametersas

shown.

24


28/41

ClickOK.

Inthedrawingarea,selectpointtodefinethelocationofthe

distributionline.

Clicktospecifythelocationofthedescription.

You

have

defined

rebar

number

3.

ClickASD ReinforcementReinforcementdefinition

(Reinforcementpoint). Alternatively,clickReinforcementmenu

Reinforcement point.

Inthedrawingarea,selectrebarnumber2.


UnderDistributionparameters,selectBends,andclearEnd.

Click (Segment).

Inthedrawingarea,selectthetopsegmentsofeachstirrup,and

thenpressEnter.

IntheReinforcement pointdialog,clickOK.

25


29/41

IntheReinforcementdescriptiondialog,specifythesameparametersasforrebarnumber3,andclickOK.

Usingthemethodlearnedpreviously,definethelocationofthe

distributionlineandthedescription.

Ifnecessary,dragthestirrupdescriptionssothatthefinalcross

sectionlooksasshown.

NOTEPayattentiontothecommandlineasyoudefinerebar.

2 DefinecrosssectionBB:ClickHomeModify (Copy).Alternatively,clickModifymenu

Copy.Inthedrawingarea,selectcrosssectionAA(withoutits

designationAA)astheobjecttocopy.

Clicknexttotheexistingsectiontoplacethecopy.

Selectthedescriptionsofthestirrupsinthecopiedcrosssection,

rightclick,andclickModify.

IntheReinforcementdescriptiondialog,clearActive.

26


30/41

NOTETurningofftheActiveparameterkeepsthebarfrombeingincluded

inthereinforcementtable,thusavoidingduplicationduringcalculations

(thereinforcementpositioninsectionAAremainsactive).

ClickClose.

Repeatthe

last

3steps

for

rebar

number

2and

number

3(bottom

andupperreinforcement)inthecopiedcrosssection.Makethem

inactive.

ClickASD ReinforcementGraphicelements (Insert

sectionsymbol).Alternatively,clickReinforcementmenuGraphic

elementsInsertsectionsymbol.

NOTETheoptionletsyouinsertasectionsymbolataselectedplaceina

drawing.Symbolsaredrawnaccordingtothedefaultstylespecifiedinthe

JobPreferencesdialog.

Onthecommandline,typeBtoassignthedesignationtothe

definedsection,andthenpressEnter.

Inthedrawingarea,clicktospecifyfirstandsecondpointsofthe

sectiondesignation,andthenspecifythelocationofthesection

description(seetheimagebelow).

27


31/41

NOTEInthecopiedcrosssection(BB),therearestirrupswithlongitudinal

rebaralreadydefined.Onlyrebarnumber4requiresinformation.

ClickASD ReinforcementReinforcementdefinition

(Reinforcementpoint). Alternatively,clickReinforcementmenu

Reinforcementpoint.



Click (Insert).

Inthedrawingarea,define2rebarsasshown,andtheninsertthe

rebardescriptions.

IncrosssectionBB,verifythatpositionnumber4isactive(select

thedescription,rightclick,andclickModify).

3 DefinecrosssectionCC:ClickHomeModify (Copy).Alternatively,clickModifymenu

Copy.

Inthedrawingarea,selectcrosssectionBB(withoutitsdesignation

andwithout

rebar

number

4)

as

the

object

to

copy.

Clicknexttotheexistingsectiontoplacethecopy.

ClickASD ReinforcementGraphicelements (Insert

sectionsymbol).Alternatively,clickReinforcementmenuGraphic

elementsInsertsectionsymbol.

28


32/41

Onthecommandline,typeCtoassignthedesignationtothedefinedsection,andthenpressEnter.

Inthedrawingarea,clicktospecifyfirstandsecondpointsofthe

sectiondesignation,andthenspecifythelocationofthesection

description(see

the

image

below).

ClickASD

Reinforcement

Reinforcement

definition

(Reinforcementpoint).Alternatively,clickReinforcementmenu

Reinforcementpoint.



Click (Insert).

Inthe

drawing

area,

define

2rebars

as

shown,

and

then

insert

the

rebardescriptions.

Makesurethatallpositionsareinactiveinthiscrosssection.

Proceedtothenextexercise,CreatingaColumnandaSpread

Footing.

29


33/41

CreatingaColumnandaSpreadFooting

Inthisexercise,youwillusemacrostocreateacolumnandaspreadfooting.Ifyou

havetypicalstructuralelementsinyourmodel,youcanusemacrosinthe

Reinforcementmoduletogeneratereinforcementandformworkautomatically.

1 Createacolumn:ClickASD StructureElementsStructureelements

reinforcement (Column).Alternatively,clickReinforcement

menuTypicalstructures reinforcementColumn.

IntheReinforcementofcolumnsdialog,ontheGeometrytab,

specifythegeometryparametersasshown.

NOTEThefirststageofdefiningacolumnissimilartothefirststageof

definingformworkwhenusingthemacro.

Inthesecondstage,definereinforcementparametersofthe

column.OntheStirrupstab,specifythestirrupsparametersas

shown.

30


34/41

OntheBarstab,specifythebarsparametersasshown.

ClickOK.

Inthedrawingarea,clicktospecifyaninsertionpoint.

Deletethetablethatcontainsreinforcement,whichwasgenerated

automaticallyinthemodelspace.

2 Createaspreadfooting:ClickASD StructureElementsStructureelements

reinforcement

(Spread

footing).

Alternatively,

click

ReinforcementmenuTypicalstructures reinforcementSpread

footing.IntheSpreadfootingdialog,ontheGeometrytab,specify

theparametersasshown.

31


35/41

Inthesecondstage,definereinforcementparametersofthespread

footing.OntheBottombarstab,specifythebarsparametersas

shown.

OntheDowelstab,specifythedowelsparametersasshown.

OntheStirrupsinthepiertab,specifythestirrupsparametersas

shown.

32


36/41

ClickOK.

Inthedrawingarea,clicktospecifyaninsertionpoint.

Deletethe

table

that

contains

reinforcement

which

was

generated

automaticallyinthemodelarea.

NOTEYoucansaveyourmacrosettingsbyusingamacrotemplate

(differentthantheprojecttemplate).Yoursettingswillbeavailablelaterin

thecurrentprojectandalsoineverynewproject.

3 UsingcommonAutoCADcommands(suchasMove,Copy,andErase),putallelements(beam,column,spreadfooting)intotheframe.

33


37/41

4 Createtherightsideoftheframe:Inthedrawingarea,selectthecolumn,spreadfootingandbendbar

ofthebeam(#4).

ClickHome

Modify

(Mirror).

Alternatively,

click

Modify

menuMirror.

Clickaboveandbelowthebeamatthemidpointtospecifythefirst

andsecondpointsofthemirrorline.

5 Proceedtothenextexercise,AddingMaterialTakeoffs.

AddingMaterialTakeoffs

Inthisexercise,youwillcreatematerialtakeoffs.Calculatingtheamountofrebar

usedinaprojectistimeconsuming,andifanychangesaremade,thecalculations

needtoberedone.UsingtheTablestoolbarinAutoCADStructuralDetailing,youcan

automatetheprocessfortheinitialcalculationsandforanyrecalculationsneeded.

1 ClickASD ReinforcementTables (Maintable).Alternatively,clickReinforcementmenuReinforcementtableBars

Maintable.

2 AcceptonthecommandlinebypressingEnter,andclickinthedrawingareatoaddthetableintomodelspace.

3 ClickASD ReinforcementTables (Bars Summarytable).Alternatively,clickReinforcementmenuReinforcementtableBars

Summarytable.

4 AcceptonthecommandlinebypressingEnter,andclickinthedrawingareatoaddthetableintomodelspace.

5 ClickASD ReinforcementSettings (Preferences).Alternatively,clickReinforcementmenuPreferences.

6 OntheReinforcementtaboftheOptionsdialog,underGeneralsettings,verifythatUpdateexistingreinforcementtableoptionisselected.

7 ClickOK.34


38/41

8 Inthedrawingarea,selectthedescriptionofbarnumber4intherightcorner,rightclick,andclickModify.

9 IntheReinforcementdescriptiondialog,forNumber,enter2.10

Click

Close.

NOTEThetableshavebeenupdated,andallinformationaboutthe

reinforcementshavebeenupdated.

11 Proceedtothenextexercise,DefinitionofViews.

35


39/41

DefinitionofViews

Thesecondstageoftheprojectistocreateviews.Inthisexercise,youwillcreate

viewsinthemodelspace.

1 Creationaviewofframe.ClickASD ReinforcementTools (Createview).

Alternatively,clickReinforcementmenuToolsCreateview.

Inthedrawingarea,definetheareaoftheviewbyclickingtospecify

thefirstandsecondcornersoftheplane.Includethewholeframe,

withouttablesandcrosssections.

TypeFramefortheviewname.

Definetheviewscaleas1:20.

NOTEAviewisasingleelementwithitsownscale.

2 Createviewsofcrosssections:ClickASD ReinforcementTools (Createview).

Alternatively,clickReinforcementmenuToolsCreateview.

DefinetheareaofviewtoincludethecrosssectionofbeamAA.

Forviewname,typeSectionAA.


Usingthesamemethodandparameters,createviewsforthe

remainingcrosssections.

3 Createviewsoftables:ClickASD ReinforcementTools (Createview).

Alternatively,click

Reinforcement

menu

Tools

Create

view.

DefinetheareaofviewtoincludetheBarsMaintable.

Forviewname,typeBarsMaintable.


36


40/41

Usingthesamemethod,createaviewfortheBars Summarytable.

Theresultinglistofviewsshouldbeasshown.

4Proceed

to

the

next

exercise,

Creating

Sheets

and

Adding

Views.

CreatingSheetsandAddingViews

Inthisexercise,youwillcreatethefinalshopdrawing.Inthisstageofeveryproject,

alloperationsareperformedinprintoutlayouts.

1 OntheAutoCADlayouttab,rightclick,andclickFromtemplate.NOTEAprintoutlayoutisanAutoCADobject.Itisusedforthecomposition

ofafinalprintout.Foreachprintoutlayout,thereisoneprintout.Whenyou

layoutelementsontheprintout,youworkwithviews.Whenyouchangethe

scaleofaview,italsoimpactsthefinaldrawing.

2 IntheSelectTemplateFromFiledialog,selectanA1formattemplate(forexample,A1ASD033.dwt).

37


41/41

3 IntheInsertLayout(s)dialog,clickOK.4 ClicktheA1ASDtab.5 OnthePositionstaboftheInspector,selectFrame,rightclick,andclickAdd

to

current

Printout.

6 Inthedrawingarea,clicktospecifythebasepoint.7 Repeatthelast2stepsfortheremainingviews,andarrangethefinaldrawingasshown.

YouhavecompletedtheAutoCADStructuralDetailing2011ReinforcementModule

GettingStartedGuide.

38

Documents

Belajar Structural Detailing