Upload
ananghabibi
View
109
Download
0
Embed Size (px)
Citation preview
5/12/2018 Cara Menggunakan Mesin - slidepdf.com
http://slidepdf.com/reader/full/cara-menggunakan-mesin 1/4
Cara Menggunakan Mesin Bubut (seri-3)
Cara Menggunakan Mesin Bubut Untuk Membubut Eksentrik
Membubut eksentrik tirus dapat dilakukan dengan dua cara :
1. Cara pertama, Pergeseran Center
Kerja Persiapan :
• Tentukan putaran mesin
• Persiapkan pahat kasar, muka, dan pahat finishing
• Kotak kunci (tool box)
• Pemasangan benda kerja
• Pemasangan dan penyetelan pahat bubut.
Langkah Kerja :
•
Bubut permukaan benda kerja dengan pahat kasar mendekati diameter terbesar dan panjang yang diinginkan.
• Bubut bagian muka benda kerja (dua muka) untuk menentukan sisi penandaan pergeseransenter.
• Buat pergeseran senternya pada dua sisi penampang benda kerja
• Tempatkan benda kerja dengan penjepitan dua senter
• Bubut diameter luar sampai dengan ukuran diameter terbesar yang diinginkan
5/12/2018 Cara Menggunakan Mesin - slidepdf.com
http://slidepdf.com/reader/full/cara-menggunakan-mesin 2/4
• Ganti penjepitan benda kerja dengan senter yang kedua
• Bubut bagian eksentriknya
• Periksa kebenaran dimensi poros eksentrik yang dibuat
2. Cara kedua, Chuck Kepala Empat (Independent Chuck)
Kerja persiapan
• Tentukan putaran mesin
• Persiapkan pahat kasar, muka, dan pahat finishing
• Kotak kunci (tool box)
• Pemasangan benda kerja
• Pemasangan dan penyetelan pahat bubut.
Langkah Kerja :
• Bubut permukaan benda kerja dengan pahat kasar mendekati diameter terbesar dan panjang yang diinginkan.
• Bubut bagian muka benda kerja (dua muka) untuk menentukan sisi penandaan pergeseransenter.
• Buat pergeseran senternya pada satu sisi penampang benda kerja
• Tempatkan benda kerja pada chuck empat, atur sesuai posisi senter utama
• Bubut benda kerja sesuai dimensi yang diinginkan
• Atur benda kerja dengan merubah posisi penjepitan sesuai sumbu eksentriknya, gunakan pointer untuk membantu pergeserannya.
• Bubut bagian eksentriknya
• Periksa kebenaran dimensi poros eksentrik yang dibuat
How to Use Machine Tool (series-3)
How to Use Machine Tool For Eccentric lathe
Tapered eccentric lathe can be done in two ways:
5/12/2018 Cara Menggunakan Mesin - slidepdf.com
http://slidepdf.com/reader/full/cara-menggunakan-mesin 3/4
1. The first way, Shift Center
Work Preparation:
• Determine engine rotation
• Prepare rough chisel, face and chisel finishing
• Key Box (tool box)
• Installation of the workpiece• Installation and adjustment of lathe chisels.
Step Work:
• Machine the workpiece surface with rough chisel near the largest diameter and the desired
length.
• Turning the face of the workpiece (two faces) to determine the side shift marking a flashlight.
• Create shift his flashlight on the two sides of the workpiece cross-section
• Place the workpiece by clamping two flashlights• Lathe outer diameter up to the desired size of the largest diameter
• Replace the workpiece clamping with a flashlight the second
• Turning the eccentric
• Check the dimensions of the truth of the eccentric shaft are made
2. The second way, Chuck Head of Four (Independent Chuck)
preparatory work
5/12/2018 Cara Menggunakan Mesin - slidepdf.com
http://slidepdf.com/reader/full/cara-menggunakan-mesin 4/4
• Determine engine rotation
• Prepare rough chisel, face and chisel finishing
• Key Box (tool box)
• Installation of the workpiece
• Installation and adjustment of lathe chisels.
Step Work:
• Machine the workpiece surface with rough chisel near the largest diameter and the desired
length.
• Turning the face of the workpiece (two faces) to determine the side shift marking a flashlight.
• Create shift his flashlight on one side of the workpiece cross-section
• Place the workpiece on the chuck four, set according to the position of the main torch
• Machine the workpiece according to the desired dimensions• Set the workpiece clamping position by changing the corresponding eccentric axis, use the
pointer to help the shift.
• Check the dimensions of the truth of the eccentric shaft are made
• Turning the eccentric
Nama :1. Sumito
2.Virgian dwi
Kelas : XII-Tpm 3