CC(STi) Cruise Control STi

7/25/2019 CC(STi) Cruise Control STi

1/8

CRUISE CONTROL SYSTEM

(STi)


2/8CC(STi)-2

CRUISE CONTROL SYSTEMGENERAL DESCRIPTION

1. General Description

A: COMPONENT

B: CAUTION Before disassembling or reassembling parts, al-ways disconnect the battery ground cable. Whenrepairing the radio, control module and other partswith memory functions, make note of the memorybefore disconnecting the battery ground cable. All

memory will be erased. Reassemble parts in the reverse order of disas-sembly unless otherwise indicated. Adjust parts to specifications specified in thismanual. Connect the connectors and hoses securely dur-ing reassembly. After reassembly, ensure functional parts oper-ate properly.

C: PREPARATION TOOL

(1) Engine control module (ECM) (3) Cruise indicator light & cruise set

indicator light

(4) Stop light and brake switch

(2) Cruise control command switch

(with built-in main switch)

(5) Clutch switch

CC-00196

(2)

(4)(5)

(1)

(3)

TOOL NAME REMARKS

Circuit Tester Used for measuring resis-tance and voltage.


3/8CC(STi)-3

CRUISE CONTROL SYSTEMCRUISE CONTROL MODULE

2. Cruise Control Module

A: NOTEEngine Control Module (ECM) controls cruise con-trol system.

B: REMOVAL

C: INSTALLATION


4/8CC(STi)-4

CRUISE CONTROL SYSTEMCRUISE CONTROL COMMAND SWITCH

3. Cruise Control CommandSwitch

A: REMOVAL

WARNING:Before servicing, be sure to read the notes inthe AB section for proper handling of the driv-er's airbag module.

1) Set the front wheels in straight ahead position.2) Turn the ignition switch to OFF.3) Disconnect the ground cable from battery andwait for at least 20 seconds before starting work.4) Using the TORX BIT T30 (Tamper resistanttype), loosen the two TORX bolts which securedriver's airbag module.

5) Disconnect the airbag module connector onback of airbag module.6) Remove the steering wheel. 7) Remove four screws, and then remove the lowercover from steering wheel.

8) Remove the screw, and then remove the cruisecontrol command switch from lower cover.

B: INSTALLATIONInstall in the reverse order of removal.

C: INSPECTIONMeasure the cruise control command switch resis-tance.

If NG, replace the cruise control command switch.

(1) TORXBIT T30

CC-00018

(1)

CC-00181

Switch Position Terminal No. Standard value

CANCEL ON 1 (+) and 2 () Less than 1 ON 1 (+) and 3 () Less than 1

SET/COASTOFF 1 and 3 More than 1 M

ON 1 and 3 Less than 1

RESUME/

ACCEL

OFF 1 and 2 More than 1 M

ON 1 and 2 Less than 1

MAIN

SWITCH

OFF 5 and 4 More than 1 M

ON 5 and 4 Less than 1 M

CC-00182

CC-00184

3 1245


5/8CC(STi)-5

CRUISE CONTROL SYSTEMSTOP LIGHT AND BRAKE SWITCH

4. Stop Light and Brake Switch

A: REMOVAL1) Disconnect the ground cable from battery.2) Disconnect the connector from stop light andbrake switch, and then remove the switch.


C: INSPECTIONMeasure the brake switch (A) and stop light switch(B) resistance.

If NG, replace the stop light and brake switch.

Switch Pedal Terminal No. Standard value

BrakeReleased 1 and 4 Less than 1

Depressed 1 and 4 More than 1 M

Stop lightReleased 2 and 3 More than 1 M

Depressed 2 and 3 Less than 1

CC-00022

12

34

(A)

(B)

321 4


6/8CC(STi)-6

CRUISE CONTROL SYSTEMCLUTCH SWITCH

5. Clutch Switch

A: REMOVAL1) Disconnect the ground cable from battery.2) Disconnect the connector from clutch switch,and then remove the switch.


C: INSPECTIONMeasure the clutch switch resistance.

If NG, replace the clutch switch.

Switch Pedal Terminal No. Standard value

ClutchReleased 1 and 2 Less than 1

Depressed 1 and 2 More than 1 M

CC-00023


7/8CC(STi)-7


NEUTRAL POSITION SWITCH

6. Neutral Position Switch

A: REMOVAL

B: INSTALLATION

C: INSPECTION


8/8CC(STi)-8


NEUTRAL POSITION SWITCH

Documents

CC(STi) Cruise Control STi