Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
FunktionsprinzipDer CDP 40 ist ein kosteneffizienter und geräuscharmer Schwimmbadentfeuchter. Der CDP 40 arbeitet nach dem Kondensationsprinzip. Ein Ventilator saugt die feuchte Raumluft ins Gerät und führt sie über den Verdampfer der Kälteanlage. Hier wird die Luft gekühlt, und durch Taupunktunterschreitung kondensiert über-schüssiger Wasserdampf zu flüssigem Wasser, das über eine Tropfenschale zu ei-nem Abfluss geleitet wird. Anschließend wird die abgekühlte, entfeuchtete Luft in dem Kondensator der Kälteanlage wieder erwärmt, bevor sie mit einer Tempera-tur, die ca. 5°C höher als beim Lufteintritt liegt, in den Raum zurückgeführt wird.
Anwendungen• Private Schwimmhallen• Therapiebäder• Spas• Wellnessbereiche
CDP 40 SCHWIMMBADENTFEUCHTER
SCHWIMMBADENTFEUCHTER CDP
EIGENSCHAFTEN
Entfeuchter• Starkes und robustes Gehäuse aus feuerverzinktem pulverlackiertem
Stahlblech• Epoxybeschichtete Verdampfer- und Kondensatorflächen für hohe
Korrosionsbeständigkeit• Wandmontage an mitgelieferter Wandschiene• Kondensatabführung am Boden. Ablaufstutzen für ¾” Schlauch• Externer elektrischer Anschluss
Steuerung• Eingebauter elektronischer Hygrostat und Thermostat• Integrierte EIN/AUS Steuerung von Feuchtigkeit und Temperatur
(elektrisches Heiz- und Warmwasserheizregister sind als extra Zubehör erhältlich)
• 0-VOLT Alarmanschluss• 230 V Anschluss für Steuerventil, Fortluftventilator und Pumpe/Kessel• RS 485 Schnittstelle für BMS (Modbus)
LeuchtdiodenBLAU: Spannung liegt an, Stand-by-ModusGRÜN: Der Kompressor arbeitet, AbtauungGELB: FernkopplungsmodusROT: Fehler
AbtauungDie elektronische Steuerung ist mit automatischer Heiβgasabtauung aus-gerüstet.
WartungFür eine einfache Wartung wird der Kältemittelkreislauf mit einem Wartungsven-til versorgt. Um die Fehlersuche zu vereinfachen, verfügt das Bedienungspaneel über eine USB-Schnittstelle zur Erfassung von historischen Daten.
Modell CDP 40Arbeitsbereich – Feuchte 40 – 100% r.FArbeitsbereich - Temperatur 10 – 36°CLuftleistung 400 m3/hNetzanschluss 1x230/50 V/HzMax. Stromaufnahme 3,8 AMax. Leistungsaufnahme 0,9 kWKältemittel R407CKältemittelmenge 0,7 kgKompressor RotationVentilator RadialGeräuschpegel (1 m vom Gerät) 46 dB(A)Filter G3 PPI 15Gewicht 56,5 kgFarbe (Gehäuse/Frontabdeckung) RAL 7035/9016Schutzart IPX4Korrosionsschutzklasse nach EN/ISO 12944-2 C4
dantherm.com
TECHNISCHE DATEN
LEISTUNGSDIAGRAMM
INSTALLATION
SCHWIMMBADENTFEUCHTER CDP
Die Schwimmbadentfeuchter CDP 40-50-70 sind für die direkte Installation in dem zu entfeuchtenden Schwimmbad oder Bereich ausgelegt.
0
5
10
15
20
25
30
35
40
0 0,5 1,0 1,5 2,0 2,5
Temp. oC
L/H
CDP 40
40% RF 60% RF 80% RF
Spezifischer Energieverbrauch (SEC): 0,47 kWh/l bei 28°C & 60% r.F.
Temp. °C
SCHWIMMBADENTFEUCHTER CDP
ABMESSUNGEN CDP 40
ZubehörDrahtlose Fernbedienung, DRC1Fuβgestell, 2 Stck.WarmwasserheizregisterWasserventil für WarmwasserheizregisterElektrisches HeizregisterFortluftventilator
dantherm.com
Alle Dimensionen sind in mm angegeben.
Fußgestell für die Aufstellung am Boden
Position des Ablaufs
Empfohlene Plazierung des Gerätes CDP 40
Min
. 225
M
in. 2
25
727
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S process equipment and is only entended as a guide.
CDP Large
CDP Large
8
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S. All designs originated by Dantherm Air Handling A/S are the property of said Company and will be protected by Patents.
Surface appearance according to referencetable LZT 142 0001, category
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
DETAIL ASCALE 1 : 2
A
table LZT 142 0001, category process equipment and is only entended as a guide.
CDP Large
CDP Large
8
property of said Company and will be protected by Patents.
Surface appearance according to reference
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S
REF.:
DATE:All designs originated by Dantherm Air Handling A/S are the
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 50 - 1160
CDP 40 - 1010
CDP 70 - 1495
56,
4 430,2
315,6
769
,2
699
,9
326,1
Min
. 225
Min
. 225
727
430,2
56,4
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S process equipment and is only entended as a guide.
CDP Large
CDP Large
8
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S. All designs originated by Dantherm Air Handling A/S are the property of said Company and will be protected by Patents.
Surface appearance according to referencetable LZT 142 0001, category
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
913
950
,5
950,
5
913
298
315,6315,6
table LZT 142 0001, category process equipment and is only entended as a guide.
CDP Large
CDP Large
8
property of said Company and will be protected by Patents.
Surface appearance according to reference
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S
REF.:
DATE:All designs originated by Dantherm Air Handling A/S are the
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 50 - 1160
CDP 40 - 1010
CDP 70 - 1495
56,
4 430,2
315,6
769
,2
699
,9
326,1
1010
769,
2
315,6
699,
9
326,1
FunktionsprinzipDer CDP 50 ist ein kosteneffizienter und geräuscharmer Schwimmbadentfeuchter. Der CDP 50 arbeitet nach dem Kondensationsprinzip. Ein Ventilator saugt die feuchte Raumluft ins Gerät und führt sie über den Verdampfer der Kälteanlage. Hier wird die Luft gekühlt, und durch Taupunktunterschreitung kondensiert über-schüssiger Wasserdampf zu flüssigem Wasser, das über eine Tropfenschale zu ei-nem Abfluss geleitet wird. Anschließend wird die abgekühlte, entfeuchtete Luft in dem Kondensator der Kälteanlage wieder erwärmt, bevor sie mit einer Tempera-tur, die ca. 5°C höher als beim Lufteintritt liegt, in den Raum zurückgeführt wird.
Anwendungen• Private Schwimmhallen• Therapiebäder• Spas• Wellnessbereiche
CDP 50 SCHWIMMBADENTFEUCHTER
SCHWIMMBADENTFEUCHTER CDP
EIGENSCHAFTEN
Entfeuchter• Starkes und robustes Gehäuse aus feuerverzinktem pulverlackiertem
Stahlblech• Epoxybeschichtete Verdampfer- und Kondensatorflächen für hohe
Korrosionsbeständigkeit• Wandmontage an mitgelieferter Wandschiene• Kondensatabführung am Boden. Ablaufstutzen für ¾” Schlauch• Externer elektrischer Anschluss
Steuerung• Eingebauter elektronischer Hygrostat und Thermostat• Integrierte EIN/AUS Steuerung von Feuchtigkeit und Temperatur
(elektrisches Heiz- und Warmwasserheizregister sind als extra Zubehör erhältlich)
• 0-VOLT Alarmanschluss• 230 V Anschluss für Steuerventil, Fortluftventilator und Pumpe/Kessel• RS 485 Schnittstelle für BMS (Modbus)
LeuchtdiodenBLAU: Spannung liegt an, Stand-by-ModusGRÜN: Der Kompressor arbeitet, AbtauungGELB: FernkopplungsmodusROT: Fehler
AbtauungDie elektronische Steuerung ist mit automatischer Heiβgasabtauung aus-gerüstet.
WartungFür eine einfache Wartung wird der Kältemittelkreislauf mit einem Wartungsven-til versorgt. Um die Fehlersuche zu vereinfachen, verfügt das Bedienungspaneel über eine USB-Schnittstelle zur Erfassung von historischen Daten.
Modell CDP 50Arbeitsbereich – Feuchte 40 – 100% r.FArbeitsbereich - Temperatur 10 – 36°CLuftleistung 680 m3/hNetzanschluss 1x230/50 V/HzMax. Stromaufnahme 6,6 AMax. Leistungsaufnahme 1,5 kWKältemittel R407CKältemittelmenge 0,9 kgKompressor RotationVentilator RadialGeräuschpegel (1 m vom Gerät) 47 dB(A)Filter G3 PPI 15Gewicht 65 kgFarbe (Gehäuse/Frontabdeckung) RAL 7035/9016Schutzart IPX4Korrosionsschutzklasse nach EN/ISO 12944-2 C4
dantherm.com
TECHNISCHE DATEN
LEISTUNGSDIAGRAMM
INSTALLATION
SCHWIMMBADENTFEUCHTER CDP
Die Schwimmbadentfeuchter CDP 40-50-70 sind für die direkte Installation in dem zu entfeuchtenden Schwimmbad oder Bereich ausgelegt.
0
5
10
15
20
25
30
35
40
0 0,5 1,0 1,5 2,0 2,5
Temp. oC
L/H
CDP 40
40% RF 60% RF 80% RF
Spezifischer Energieverbrauch (SEC): 0,48 kWh/l bei 28°C & 60% r.F.
0
5
10
15
20
25
30
35
40
0 0,5 1,0 1,5 2,0 2,5 3,0 3,5 4,0
Temp.
L/H
60% r.F. 80% r.F.
CDP 50
40% r.F.Temp. °C
SCHWIMMBADENTFEUCHTER CDP
ABMESSUNGEN CDP 50
ZubehörDrahtlose Fernbedienung, DRC1Fuβgestell, 2 Stck.WarmwasserheizregisterWasserventil für WarmwasserheizregisterElektrisches HeizregisterFortluftventilator
dantherm.com
Alle Dimensionen sind in mm angegeben.
Fußgestell für die Aufstellung am Boden
Position des Ablaufs
Empfohlene Plazierung des Gerätes CDP 50
Min
. 225
M
in. 2
25
727
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S process equipment and is only entended as a guide.
CDP Large
CDP Large
8
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S. All designs originated by Dantherm Air Handling A/S are the property of said Company and will be protected by Patents.
Surface appearance according to referencetable LZT 142 0001, category
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
DETAIL ASCALE 1 : 2
A
table LZT 142 0001, category process equipment and is only entended as a guide.
CDP Large
CDP Large
8
property of said Company and will be protected by Patents.
Surface appearance according to reference
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S
REF.:
DATE:All designs originated by Dantherm Air Handling A/S are the
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 50 - 1160
CDP 40 - 1010
CDP 70 - 1495
56,
4 430,2
315,6
769
,2
699
,9
326,1
Min
. 225
Min
. 225
727
430,2
56,4
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S process equipment and is only entended as a guide.
CDP Large
CDP Large
8
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S. All designs originated by Dantherm Air Handling A/S are the property of said Company and will be protected by Patents.
Surface appearance according to referencetable LZT 142 0001, category
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
913
950
,5
950,
5
913
298
table LZT 142 0001, category process equipment and is only entended as a guide.
CDP Large
CDP Large
8
property of said Company and will be protected by Patents.
Surface appearance according to reference
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S
REF.:
DATE:All designs originated by Dantherm Air Handling A/S are the
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 50 - 1160
CDP 40 - 1010
CDP 70 - 1495
56,
4 430,2
315,6
769
,2
699
,9
326,1
1160
769,
2
315,6
699,
9
326,1
FunktionsprinzipDer CDP 70 ist ein kosteneffizienter und geräuscharmer Schwimmbadentfeuchter. Der CDP 70 arbeitet nach dem Kondensationsprinzip. Ein Ventilator saugt die feuchte Raumluft ins Gerät und führt sie über den Verdampfer der Kälteanlage. Hier wird die Luft gekühlt, und durch Taupunktunterschreitung kondensiert über-schüssiger Wasserdampf zu flüssigem Wasser, das über eine Tropfenschale zu ei-nem Abfluss geleitet wird. Anschließend wird die abgekühlte, entfeuchtete Luft in dem Kondensator der Kälteanlage wieder erwärmt, bevor sie mit einer Tempera-tur, die ca. 5°C höher als beim Lufteintritt liegt, in den Raum zurückgeführt wird.
Anwendungen• Private Schwimmhallen• Therapiebäder• Spas• Wellnessbereiche
CDP 70 SCHWIMMBADENTFEUCHTER
SCHWIMMBADENTFEUCHTER CDP
EIGENSCHAFTEN
Entfeuchter• Starkes und robustes Gehäuse aus feuerverzinktem pulverlackiertem
Stahlblech• Epoxybeschichtete Verdampfer- und Kondensatorflächen für hohe
Korrosionsbeständigkeit• Wandmontage an mitgelieferter Wandschiene• Kondensatabführung am Boden. Ablaufstutzen für ¾” Schlauch• Externer elektrischer Anschluss
Steuerung• Eingebauter elektronischer Hygrostat und Thermostat• Integrierte EIN/AUS Steuerung von Feuchtigkeit und Temperatur
(elektrisches Heiz- und Warmwasserheizregister sind als extra Zubehör erhältlich)
• 0-VOLT Alarmanschluss• 230 V Anschluss für Steuerventil, Fortluftventilator und Pumpe/Kessel• RS 485 Schnittstelle für BMS (Modbus)
LeuchtdiodenBLAU: Spannung liegt an, Stand-by-ModusGRÜN: Der Kompressor arbeitet, AbtauungGELB: FernkopplungsmodusROT: Fehler
AbtauungDie elektronische Steuerung ist mit automatischer Heiβgasabtauung aus-gerüstet.
WartungFür eine einfache Wartung wird der Kältemittelkreislauf mit einem Wartungsven-til versorgt. Um die Fehlersuche zu vereinfachen, verfügt das Bedienungspaneel über eine USB-Schnittstelle zur Erfassung von historischen Daten.
0
5
10
15
20
25
30
35
40
0 1 2 3 4 5 6
Temp.
L/H
CDP 70
40% r.F. 60% r.F. 80% r.F.
Modell CDP 70Arbeitsbereich – Feuchte 40 – 100% r.FArbeitsbereich - Temperatur 10 – 36°CLuftleistung 900 m3/hNetzanschluss 1x230/50 V/HzMax. Stromaufnahme 8 AMax. Leistungsaufnahme 1,8 kWKältemittel R407CKältemittelmenge 1,2 kgKompressor RotationVentilator RadialGeräuschpegel (1 m vom Gerät) 50 dB(A)Filter G3 PPI 15Gewicht 75,5 kgFarbe (Gehäuse/Frontabdeckung) RAL 7035/9016Schutzart IPX4Korrosionsschutzklasse nach EN/ISO 12944-2 C4
dantherm.com
TECHNISCHE DATEN
LEISTUNGSDIAGRAMM
INSTALLATION
SCHWIMMBADENTFEUCHTER CDP
Die Schwimmbadentfeuchter CDP 40-50-70 sind für die direkte Installation in dem zu entfeuchtenden Schwimmbad oder Bereich ausgelegt.
Spezifischer Energieverbrauch (SEC): 0,43 kWh/l bei 28°C & 60% r.F.
Temp. °C
SCHWIMMBADENTFEUCHTER CDP
ABMESSUNGEN CDP 70
ZubehörDrahtlose Fernbedienung, DRC1Fuβgestell, 2 Stck.WarmwasserheizregisterWasserventil für WarmwasserheizregisterElektrisches HeizregisterFortluftventilator
dantherm.com
Alle Dimensionen sind in mm angegeben.
Fußgestell für die Aufstellung am Boden
Position des Ablaufs
Empfohlene Plazierung des Gerätes CDP 70
Min
. 225
M
in. 2
25
727
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S process equipment and is only entended as a guide.
CDP Large
CDP Large
8
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S. All designs originated by Dantherm Air Handling A/S are the property of said Company and will be protected by Patents.
Surface appearance according to referencetable LZT 142 0001, category
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
DETAIL ASCALE 1 : 2
A
table LZT 142 0001, category process equipment and is only entended as a guide.
CDP Large
CDP Large
8
property of said Company and will be protected by Patents.
Surface appearance according to reference
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S
REF.:
DATE:All designs originated by Dantherm Air Handling A/S are the
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 50 - 1160
CDP 40 - 1010
CDP 70 - 1495
56,
4 430,2
315,6
769
,2
699
,9
326,1
Min
. 225
Min
. 225
727
430,2
56,4
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S process equipment and is only entended as a guide.
CDP Large
CDP Large
8
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S. All designs originated by Dantherm Air Handling A/S are the property of said Company and will be protected by Patents.
Surface appearance according to referencetable LZT 142 0001, category
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
913
950
,5
950,
5
913
298
table LZT 142 0001, category process equipment and is only entended as a guide.
CDP Large
CDP Large
8
property of said Company and will be protected by Patents.
Surface appearance according to reference
g
SCALE: NOT TO SCALE
351 512
351512
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
PART NO REV.:
REV.:
PAR
TN
O
Sheetmetal flatstate is based on Dantherm Air Handling A/S
REF.:
DATE:All designs originated by Dantherm Air Handling A/S are the
This Drawing is furnished with the understanding that the essence there of will not be reproduced in whole or in part without written authorization by Dantherm Air Handling A/S.
Linear dimensions without tolerances according to DS/EN 22768-1 medium. Angular dimensions without tolerances: ± 1°
CDP 50 - 1160
CDP 40 - 1010
CDP 70 - 1495
56,
4 430,2
315,6
769
,2
699
,9
326,1
1495
769,
2
315,6
699,
9
326,1