Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Thermal Expansion & Fire-Protection Material "Fi-Block"
熱膨張性耐火材料[フィブロック]製品 Product 特徴 Features
想定用途 Possible Appplications
●火災時の熱で膨張することで、耐火性・断熱性を発揮
・It is a thin sheet and can be served as a tape in normal times, which makes it easy to bend and cut it.
加熱heating
10~30 張 10 30times expansion
膨張し、断熱層を形成 !Heat Insulation layer formed
Cell
1
Cell
2
Fi-Block
Cell Heat
Fi-Block Expansion
Heat insulation layer protects the cells from thermal runaway
Cell
1
Cell
2
Cell
1
Cell
2
Cell
3
Cell
4
Heat
Heat
類焼防止対策 To protect the cells from Thermal Runaway
膨張 ●通常時には薄いシートやテープとしても 取り扱うことができるため、曲げ加工や切断が簡単にできます。
・Fi-Block demonstrates fire-resistant and fire-proof properties only when it expands in reaction to heat generated by fire.
積水化学工業株式会社 耐火材料営業所 担当:玉川 TEL.03-5521-0526 mail. [email protected] SEKISUI CHEMICAL CO.,LTD. Fire Protection Materials Sales Office TEL:03-5521-0526 [email protected]
問 合 せ 先Contact us
<通常時/Normal State> <セル①異常時 /Thermal Runawa at Cell1>
物性 Properties
注) 本データは、測定であり、保証値ではございません。Note: These data is only measured, not guaranteed.
High Fire-resistant Rigid Polyurethane Foam "PUXFLAME"
高耐火性硬質ポリウレタン[パックスフレイム]開発品Under Development
特徴 Features製品 Product
メカニズム Mechanism
物性 Properties
●熱せられると炭化層形成することで酸素と 可燃ガスの結合を遮断し、不燃性を実現します。
・Puxflame has the same features as normal polyurethane.
・Puxflame performs high fire-resistant by forming carbon layer on its surface after heated.
炭化層を形成酸素と可燃ガスの結合を遮断Carbon layer formed on the surface to block O₂ from bonding the gas
分解抑制難燃剤が酸素と反応Suppress the discompositionFlame retardant reacts O₂
樹脂構造強化難燃剤添加Reinforce the resin structureadding flame retardant
酸素と可燃ガスが結合し燃焼O₂ bond with the gas and burn
樹脂分解可燃ガス発生Resin DecompositionComustible Gas comes out
加熱Heated
注) 本データは、測定であり、保証値ではございません。Note: These data is only measured, not guaranteed.
バーナー燃焼試験/ Burner Test
Puxflame Polyurethane
バーナー燃焼試験/ Burner Test
Puxflame Polyurethane
物性値Properties
単位Unit
パックスフレイムPUXFLAME
不燃性能(UL-94) ― 5V-A相当
密度Density Kg/m3 48
圧縮強度Compressive Strength N/cm2 30 以上
more than 30
熱伝導率Thermal Conductivity W/(m ・K) 0.03
吸水率Water Absorption g/100cm2 1.1 以下
less than 1.1
●一般的な硬質ウレタンの特徴を有しています。
EVA(開発中)(Under
development)
形状Shape
シート/短冊Sheet/Strip
シート/ロールSheet/Roll
押出成型ExtrusionMolding
射出成型InjectionMolding
シート/ロールSheet/Roll
ベース樹脂Based Resin
エポキシEpoxy PVC PVC PVC
写真Images
20~
膨張開始時間Expansion Temp. ℃
150~200~ 200~ 200~ 200~ 150~
膨張倍率Expansion Degree
倍Times 30~40 25 15~30 15~30
0.8~1.2
熱伝導率Thermal Conductivity W/(m・K)
Before : 0.47 Before : 0.28N/A N/A
Before : 0.30
After : 0.29 After : 0.23
膨張圧力Expansion Pressure Mpa 0.4~0.47 0.31 0.33~1.34 N/A
After : 0.10
絶縁性Electric Insulation Ω 9X10^14 7X10^12 N/A N/A 9X10^14
0.15~0.3
難燃性Flame Retardant
(UL-94)
内部試験Internal Test
(equivalent to)V-0
(equivalent to)V-0 N/A N/A (equivalent to)
V-0
厚みThickness mm 1.0~2.0 1.0~2.0 - -
火源(Fire)
酸素/O₂
可燃ガス/Combustible Gas 難燃剤/Flame Retardant
通常ポリウレタンnormal polyurethane
パックスフレイムPUXFLAME