DEKDEK 中級培訓中級培訓

1 ． Rail to Table Height

2 ． Setting camera reference position

3 ． Setting Print Height

4 ． Calibrate Vision

5 ． CALIBRATION OFFSET

6 ．軟體的安裝

Rail to Table HeightRail to Table Height • 1:In Diagnostics select Rising Table module.• 2:Select Home Rising Table and Exit Rising Table module.• 3:Select Rail System Module.• 4:Select Home Rail Width.`• 5:Select Adjust Rail Width•

• 6. Set the board width. 治具的寬度 .• 7. Select drive rail to board width • 8. Select 鬆開夾邊• 9. 將治具板放在軌道的兩邊 .• 10. Select 夾緊夾邊• 11.Select rising table module.• 12.Select table to vision height.

調試調試 RISING TABLERISING TABLE 高度高度

Setting camera reference positionSetting camera reference position

• In camera Axes Diagnostics, select Home Camera X Axis and Run Diagnost.

• Select Home Camera Y Axis and Run Diagnost.

• Select Drive to Reference Position and select Run Diagnost. A box and the white dot on the board clamp is visible on the monitor.

• Using Move Camera X Axis Using Jog Buttons and Move Camera Y Axis Using Jog Buttons, position the box centrally inside the white dot, as shown.

Jog ButtonsJog Buttons

Select Set Reference Position and select Run Diagnost.

Setting Print HeightSetting Print Height 1:Select Diagnostics• 2:Select Screen Change.• 3:Select 鎖定 Screen• 4:Selct Camera Axes• 5:Select Home Camera X Axis• 6:Select Home camera Y Axis • 7:Select Rising Table• 8:Select Home Rising Table• 9:Select Set Reference Print Height, the rising

table

10: Using the Incr. And Decr. buttons adjust the displayed dimension.

• 11:Press the Move button, check rising table• 是否到位 .• 12:select Set Height. 將這個高度設置為印刷高度 .• 13:Select save the new print height, select Exit.

Selecting Exit only, returns to the previous menu without the changes being saved.

Calibrate VisionCalibrate Vision

5:Press Change Screen

CALIBRATION OFFSETCALIBRATION OFFSET

軟體的安裝軟體的安裝

1. 將安裝光盤放到機器的光驅里2. 將機器設置為從光驅起動 , 然后重啟 .

3.Run DEK Set-up program

Option 1 to replace Windows NT partition

Option 2 to reload the entire disk.

Option 3 Backup Product and Calibration Data

4. 選擇 Option 2 機器開始自動安裝軟体 .

5.Select Next

6. 自動 RUN GHOST 安裝軟体 .

7. 安裝完成后 , 自動重啟 .

8. 機器重啟后會讓我們插入一張 A 盤

9 . 可不插入軟碟， Select CANCEL10.DEKSYSTEM 啟動完成后開始初始化 .• 初始化完成後，若無 CLEAN SCREEN 這項功能，

請按如下步驟添加：• 1.Press Maint.(F8)• 2.Press Set Prefs(F5)• 3.Press F10• 4. 輸入 Clean on• 5.Press Exit (F8)• 6.Press Exit (F8)• 然後關機重新啓動即可。

對軟體升級對軟體升級

1. 進入 DIAGNOSTICS//SYSTEM//Terminate Control Program.

2. 放光碟於光驅，讓其自行安裝3. 輸入機器序列號即可4. 重新啓動機器。

The EndThe End