Profile Jay Jagannath Air Equipments is a manufacturing company supplying both pre-engineered and custom

engineered Desiccant Dehumidifier, Air Handling Unit and HVAC related products to the commercial and industrial marketplace. It is our mission to provide our customers to high quality, energy efficient products at competitive pricing and with best service in Industry, while achieving a reasonable profit. We will strive to assure correct application of our products to our customer's need.

Vision Statement To continually create and nurture a healthy, profitable company for the purpose of serving the needs

of people (customers, employees, representatives, vendors, community, and thers) in order to enhance the quality of their lives, help them reach their potential, and recognize the value they were created with.

Strength Energy Efficient & Environment supportive Design Strong application and Technical Support Excellent pre sales and after sales backup Flexible and adaptable Customized solution and yet affordable Well experienced service staff

Achievments We have achieved <7Grains/Lb (-18 D.P)@5 C We have achieved <4Grains/Lb (-21 D.P)@50 C For Coating Pan. We have achieved 12% RH@20 C For Soft Gelatin Capsule Drying.

Key Salient Features of our Dehumidifier

Jay Jagannath Air Equipments dehumidifiers are the most energy efficient products in the industry. Flexibility in Design and Air Quantity selection - We design and Manufacture the Unit with Required

calculated capacity and Our unit model varies as per required calculated Air quantity i.e. If 2300 CFM is calculated capacity of Unit then We provide unit with the same capacity but in case of other supplier's Unit Fixed Model are there as they recommend 2500 CFM in place of 2300 CFM that puts extra burden on Utility and Cost.

Space Friendly : We provide Engineering / AHU cum Dehumidifier in Combo unit form hence saves a lot of Floor Space Area in place using AHU and Dehumidifier separately .

Blowers and Motor : Blowers and motors are used of standard Make (Made in Germany ) within competitive cost.

Efficient Dehumidifier Desiccant Rotor (Imported ) with Minimum Pressure Drop across and requires Steam at low pressure at 3-5 kg/cm2 and with low regeneration Temperature around 90-100 Deg. C .

Standard Filtration : We use only standard make Filters in AHU and Dehumidifiers always . Spare parts Availability : All the spare parts are readily available with us at Factory so we

consume less time to deliver the same . Electrical control panel which is of L&T/SIEMENS make. PLC is of Allen Bradley/Mitsubishi. Sensors are of Honeywell/Radix.All this adds to the efficiency

of the product. Our After sales Service is our salient feature , we offer after sales service without any extra

labour / service charge till the stipulated time and Our Service Engineer and Technicians are readily available to provide you timely service.

Our unit Panel are 43+/-2mm Puff Insulated Panel with pre coated inner and outer sheet. We are using puff panel for filter frame also.

Master Process Controller :

Feature : It Monitor Process RH & Temperature. It Monitor Regeneration Air Inlet Temperature. The instruments are simple to configure and use, while

providing tremendous versatility and a wealth of powerful features.

Alarm indication by hooter.

Working Principle

The process air passes through 7 5% of the desiccant rotor surface with t he help of suction or process blower, which produces Dry discharge air with low relative humidity. This Dry is discharged to the AHU or moisture conditioned space. At the same time Heat is being applied to the remaining 25% of rotor surface to reactivate the desiccant material. Resulting wet air is discharged outside.

Working Principle The process air passes through 50% of the desiccant rotor surface with t he help of suction or process blower, which

produces Dry discharge air with low relative umidity. This Dry is discharged to the AHU or moisture conditioned space. At the same time Heat is being applied to the remaining 25% of rotor surface to reactivate the desiccant material. Resulting wet air is discharged outside.

This Cycle is implemented by Jay Jagannath Air Equipments.E.G. : Regen. air inlet temperature is coming at 70 C because the rotor is itself heated.Now we have to took this regen. Air from 70 C to 140 C,so my T is 70 C in this case.In conclusion the energy consumption is less as compared to previous cycle.

WORKING PRINCIPLE & BENEFIT OF ROTOR Used by M/s. Jay Jagannath Air Equipments :

Above Dehumidifier Rotor cycle is energy efficient cycle compare to other Manufacturers. In Above picture we have mention total 3 parts of Rotor where 50% surface area of Rotor used to remove the moisture of Return air from the area to maintain require Humidity in Area. Out of another 50% surface area they divided in 2 parts as 25% of each area where 25% area in blue line is shown the indication of wet air which have absorbed Moisture content from the Rotor, Another 25% surface area used to pre heat & to Dehumidified Regeneration air of Dehumidifier.

Let’s assume the Ambient Condition as 30 Deg.C & 154 Gr/Lb. Ambient Air will pass through the 25% Pre heat area of Regeneration so it will be around 60 - 70 Deg.c & 130 Gr/Lb before the Heater or Steam coil. For the regeneration of Rotor we have to maintain Temperature between 120 Deg.C to 140 Deg.C. As per above cycle we are getting 60-70 Deg.c pre heated Regeneration air before Heater or Steam Coil so we have to Increase only 50 to 70 Deg.C to Regenerate the Rotor for Maintaining of Humidity in Area, which is very low Delta T Compare to other Regeneration cycle hence it is Energy efficient Dehumidifier Cycle.

Another benefit of this Dehumidifier cycle is that it consume low amount of chilled water for Post cooling coil because Maximum heat of Rotor was absorbed by Regeneration Air in Pre Heat Section of Rotor so Process Air outlet will not be very much heated in this Dehumidifier cycle.

Below are some examples of energy efficiency :

1. Regeneration Air Heating Calculation @ 140 Deg.C in Normal Dehumidification Cycle : Ambient Air Condition - 30 Deg.C & 154 Gr/Lb.

# - Formula – 1.08 x Reg. CFM x Delta T in Deg.Farenhit = Require KW For regeneration

3412

# - Energy Efficient Dehumidifier Cycle - – 1.08 x 400 x 158

3412

= 20 KW (Delta T is 70 Deg.C) (140 – 70(PreHeat) = 70 Deg.C)

Above calculation indicates that there is low energy requirement in Above Dehumidifier cycle. As per our knowledge and practice, Total 25 to 30% energy saving in Regeneration air Heating and Process air cooling.

# - Normal Dehumidifier Cycle - 1.08 x 400 x 230 = 29.12 KW (Delta T is 110Deg.C)3412 (140 – 30(Ambient) = 110

Deg.C)

DEHUMIDIFIER MODEL DRY AIR FLOW (CMH) WET AIR FLOW (CMH)

JJ-2500 2500 833

JJ-3000 3000 1000

JJ-3500 3500 1167

JJ-4500 4500 1500

JJ-7000 7000 2333

JJ-10000 10000 3333

JJ-17000 17000 5667

SUPPLY 3 – PHASE , 415 V ,+/- 5%, 50 HzNOTE : WE WILL ALSO PROVIDE 100% STEAM GENERATION

COMPACT DEHUMIDIFIER SERIES

Application : Pharmaceuticals Food Confectionary Dry air storage Museums , Defence , Bridges , Power

plants , Shipping , Water Works.

Salient Features : Washable Rotor Standard Filter No desiccant carry-over Hygienic Desiccant rotor for

Pharmaceuticals application Long life cycle Easy to maintain Compact with aesthetic look

HEAT RESISTANCE FILTER

PLC OPERATED ELECTRIC CONTROL PANEL (OPTIONAL)

DEHUMIDIFIER MODEL DRY AIR FLOW (CMH) WET AIR FLOW (CMH)

JJ-600 600 200

JJ-1000 1000 333

JJ-1500 1500 500

JJ-2000 2000 667

SUPPLY 3 – PHASE , 415 V ,+/- 5%, 50 HzNOTE : WE WILL ALSO PROVIDE 100% STEAM GENERATION

AIR HANDLING UNIT (AHU) : Jay Jagannath Air Equipments double skin air handling unit (AHU) are designed to highest engineering standards for Indoor

Air Quality (IAQ) requirements according to ASHRAE standard 62 and meet the requirements of cooling, heating, ventilation, dehumidification and air distribution to a conditioned space.

Our AHU employs special extruded aluminum profile posts which break the thermal bridge, reinforced plastic triaxial angle lug, flush fitting panels and doors.

All panels and doors can be easily assembled and disassembled due to distinctive lockable device achieved by a steadfast PVC strip.

Filters can meet varying requirements due to a wide range of filtration classes with different materials, with removable provision, which makes them easy to access for inspection and -cleaning.

Water coil is manufactured from copper tubes with aluminum fins. Heat source can be hot water, electricity or steam. Dry Drain Pan design allows rapid and trouble-free drainage of condensate water. Powder coated galvanized steel filter frames. Pre and fine filter from 10 μ to 0.3 μ filtration. Airfoil blade Aluminum dampers suitable for actuator or manual operation. Wide range of models from 200 cmh to 85,000 cmh. Custom Built AHUs for special requirements apart from standard models. TEFC type, class B or F insulation and IP54 or IP55 protection Motor. Certified DIDW centrifugal or plug type Blower.

AIR HANDLING UNIT (AHU) : Feature : Thermal Break Alluminium Profile Easy Access Flexible Assembly Better heat Insulation Air tight Heating and cooling coil Humidifier Segment (Optional) Novel structure Operational stability Easy Installation and

Commissioning

We have a long term relationships with some leading companies. Our market position is reflected in our client list and is a testimony to our professionalism and product strength. Our partnership with our customers has always been excellent because we are solution centric and deliver results. We are responsive and adaptable to their needs. We are informal in responding to their requirements whenever the need arises-24 x7.

VALUED CLIENTS :

FOR 12% RH

FOR 25% RH

FOR 15% RH

FOR 25% RH

FOR 18% RH

FOR 100% FRESH AIRFOR 25% RH

FOR 100% FRESH AIR

FOR LESS THAN 7 GRAINS (-18 DP)

FOR 40% RH

FOR 100% FRESH AIR

And Many More……

Thank you for your attention!

You can find out more about us at www.jjgroup.org