Upload
doankhue
View
225
Download
2
Embed Size (px)
Citation preview
1
week02425250 Mechanical Drawing
TOPICS
• Surface Properties• Surface Finished• Dimensioning• General Tolerance• Fitting Table • Geometric Dimensioning and Toleranceing
Surface Properties ผิวดิบ ผานกระบวนการผลิตที่ไรเศษมีความเรียบรอยและสมํ่าเสมอของชิ้นงาน
Surface finish
ผิวหยาบ สามารถสัมผัสความหยาบไดดวยมือและมองเห็นดวยตา
ผิวละเอยีด สามารถมองเห็นความหยาบไดดวยตาเปลา
ผิวละเอยีดมาก ไมสามารถมองเห็นความหยาบไดดวยตาเปลา
JISDIN
ผานการปาดผิว
ไมผานการปาดผิว
Surface finish
DIN
ISO
Surface meter/Roughness meter
2
Surface finished
Surface finished
Surface finished
A คือ คาความหยาบผิว (Roughness, Ra)B คือ กรรมวิธีการผลิต บอกเปนตัวอักษรC คือ ความยาวชิ้นงานชวงตรวจสอบความหยาบผิวD คือ สัญลักษณทิศทางการตัดเฉือนชิ้นงานE คือ คาความเผื่อกอนการปรับผิวขั้นสุดทายF คือ คาความหยาบผิวอ่ืนๆ
Surface finished
6.3
ไมระบุกรรมวิธีการผลิต ผิ ว ง านต องมี ก า รตั ดเฉือน (ระบุกรรมวิธีการผลิต)
ground5
ผิ ว ง านที่ ผ านการตั ดเฉือนมาแลว ไมตองทําอะไรอีก
sawing
Surface finished
ExampleExample
Surface finished
SAND CASTING
3
ExampleExample
DimensioningDEFINITION
Dimensioning is the process of specifying part’ s
information by using of figures, symbols and notes.
This information are such as:1. Sizes and locations of features2. Material’s type3. Number required4. Kind of surface finish5. Manufacturing process6. Size and geometric tolerances
DIMENSIONING SYSTEM
41
1. Metric system : ISO and JIS standards
2. Decimal-inch system
3. Fractional-inch system
835,
0.25 (not .25), 5.375 etc.Examples
Examples
32, 32.5, 32.55, 0.5 (not .5) etc. Examples
etc.
Dimensioning
Basic dimensionBasic dimension
((Reference dimensionReference dimension))
Critical dimensionCritical dimension
Not to scale dimensionNot to scale dimension
4
Basic dimensionBasic dimensionReference dimensionReference dimension
Critical dimensionCritical dimension Not to scale dimensionNot to scale dimension
DimensioningComponents
DIMENSIONING COMPONENTS
Extension lines
Dimension lines(with arrowheads)
Leader lines
Dimension figures
Notes :- local note- general note
Drawn with4H pencil
Lettered with2H pencil.
5
indicate the location on the object’s features that are dimensioned.
EXTENSION LINES DIMENSION LINESindicate the direction and extent of a dimension, and inscribe dimension figures.
10 27
43
13
123 o
indicate details of the feature with a local note.
LEADER LINES
10 27
43
13
123 o
10 Drill, 2 Holes
R16
RecommendedPractices
EXTENSION LINES
Leave a visible gap (≈ 1 mm) from a view and start drawing an extension line.
Extend the lines beyond the (last) dimension line 1-2 mm.
Visible gapCOMMON MISTAKE
Do not break the lines as they cross object lines.
COMMON MISTAKEContinuous
EXTENSION LINES
6
Dimension lines should not be spaced too closeto each other and to the view.
11 34
Leave a space at least2 times of a letter height.
1635
DIMENSION LINES
Leave a space at least1 time of a letter height.
DIMENSION FIGURESThe height of figures is suggested to be 2.5~3 mm.
Place the numbers at about 1 mm above dimensionline and between extension lines.
COMMON MISTAKE
11
1134
34
16.2516.25
or
DIMENSION FIGURES
When there is not enough space for figure orarrows, put it outside either of the extension lines.
1
Not enough spacefor figures
Not enough spacefor arrows
1 1
The JIS and ISO standards adopt the unit of
Angular dimension in degree with a symbol “o”place behind the figures (and if necessaryminutes and seconds may be used together).
DIMENSION FIGURES : UNITS
Length dimension in millimeters withoutspecifying a unit symbol “mm”.
1. Aligned method
2. Unidirectional method
The dimension figures are placed so that they are readable from the bottom and right side of the drawing.
The dimension figures are placed so that they can be read from the bottom of the drawing.
Do not use both system on the same drawing or on the same series of drawing (JIS Z8317)
DIMENSION FIGURES : ORIENTATION
30
30
30
30
30
30
30
30
EXAMPLE : Dimension of length using aligned method.
7
30
30
30
30
3030
30
30
EXAMPLE : Dimension of length using unidirectional method.
45 o
45 o
45o
45o
45o
45o
45o
45o
EXAMPLE : Dimension of angle using aligned method.
45o
45o
45o
45o
45o45o
45o
45o
EXAMPLE : Dimension of angle using unidirectional method. CHAMFERUse leader line and note to indicate lineardistance and angle of the chamfer.
S
θ
S θ
For a 45o chamfer
S SCS
or
ROUNDED-END SHAPES
R12φ 12
21
5
Dimensioned according to the manufacturing method used.
Center to Center Distance
ROUNDED-END SHAPES
R12
21
5
12
Dimensioned according to the manufacturing method used.
Center to Center Distance
8
ROUNDED-END SHAPESDimensioned according to the manufacturing method used.
R12
21
12
16
ROUNDED-END SHAPES
R12
27
12
Dimensioned according to the manufacturing method used.
Tool cutting distance
ROUNDED-END SHAPESDimensioned according to the standard sizes ofanother part to be assembled or manufacturing method used.
25
Key(standard part)
ROUNDED-END SHAPESDimensioned according to the standard sizes ofanother part to be assembled or manufacturing method used.
20
ToleranceTolerance
Basic sizeBasic sizeNominal sizeNominal sizeActual sizeActual sizeToleranceToleranceAllowanceAllowance
9
Tolerance Tolerance
รูควานคงที่ ปรับคาเริ่มตนไปที่อักษร H
เพลาคงที่ ปรับคาเริ่มตนไปที่อักษร h Ø25 H7h6
พิกัดความเผ่ือของงานสวม
ระบบรูควานคงที่ ปรับคาเริ่มตนไปที่อักษร H
ระบบเพลาคงที่ ปรับคาเริ่มตนไปที่อักษร h
IT… (ISO Tolerance – series ,Quality grade)
DIN 7151 (11.64)พิกัดพ้ืนฐานระบบ ISO คาพิกัดเปน μm
10
พิกัดความเผ่ือของงานสวม
ชิ้นสวนยึดติดกันแนนมาก ไมจําเปนตองมีชิ้นสวนปองกันแรงบิดH7-s6S7-h6
สวมอัดแนน
ชิ้นสวนยึดติดอยูดวยกันแตยังสามารถถอดออกไดดวยแรงไมมากนัก เชนจานเบรก หรือ fly wheel ซึ่งประกอบกันดวยลิ่มและไมตองถอดประกอบบอย
H7-k6K7-h6
สวมยึด
ชิ้นสวนที่สวมกันพอดี สามารถเลื่อนไดเม่ือออกแรงผลักหรือกระแทกดวยมือ เชน เพลาของเฟองหรอืมูเล ที่ตองถอดประกอบบอยๆ
H7-j6J7-h6
สวมเลื่อนดวยแรงเบาๆ
ชิ้นสวนที่สวมกันพอดีแตยังสามารถเลือ่นไดดวยมือ เชน แทนยันศูนยเครื่องกลึงH7-h6H7-h6
สวมนําเลื่อน
เพลาหมุนไดในรู โดยมีชองวางนอยมาก เชน แกนเฟอง เพลาหินเจียร ที่สามารถอดเปลี่ยนได
H7-g6G7-h6
สวมคลอนนอย
เพลาหมุนไดในรู โดยมีชองวางพอประมาณ เชน ปลอกตลับลูกปนกับแกนเพลาเพลาหมุนไดในรู โดยมีชองวางนอย
H8-e8, E9-h9H7-f6, F7-h6
สวมคลอนมาก
ชิ้นสวนยึดติดกันแนน ตองออกแรงมากๆจึงจะถอดไดH7-n6N7-h6
สวมอัด
ชิ้นสวนยึดติดอยูดวยกัน ตองใชแรงตอกในการถอดประกอบ เชนแบริ่งกานสูบ แทงเพลายึดแผนฐานชิ้นงาน
H7-m6M7-h6
สวมยึดแนน
เพลาหมุนไดในรู โดยมีชองวางมาก เชน เครื่องจักรการเกษตร งานกอสรางH8-d9D10-h9
สวมหลวม
รายละเอียดสัญลักษณชื่องานสวม
11
GD&T
0.08
0.2
Straightness
ความรวมศูนย
Flatnessความเท่ียงความราบ
Circularityความเท่ียงความกลม
Cylindricityความเท่ียงรูปทรงกระบอก
พิกัดความเผ่ือของรูปราง
Tolerance
Profile of lineความเท่ียงแนวเสน
Profile of Surfaceความเท่ียงรูปทรงของพื้นท่ี
พิกัดความเผ่ือของรูปราง
พิกัดความเผ่ือของตําแหนง
Parallelความขนาน
พิกัดความเผ่ือของตําแหนง
Perpendicularความต้ังฉาก
0.4
Angularityความเอียง
Positionตําแหนง
พิกัดความเผ่ือของตําแหนง
Concentricityความรวมศูนยและความเท่ียงศูนย
Symmetryความสมดุลของขาง
Circular runoutการเคล่ือนท่ีเปนแนวหมุน
1
1
Welding
Welding Processes
ArcWelding
ResistanceWelding
GasWelding
etc. etc.
2
Gas Welding
3
Arc Welding
4
Resistance Welding
5
การตอเชื่อม (Welding joints)
6
Example of welding joints
2
7
สัญลักษณรอยเช่ือม (Welding symbol)
8
ลักษณะรอยเชื่อม (Weld)
9
1.ลักษณะการเชื่อม
-ดานลางเสน(Arrow side) : แสดงลักษณะการเชื่อมดานที่ลูกศรช้ี
-ดานบนเสน(Other side) : แสดงลักษณะการเชื่อมดานที่อยูตรงขาม
(Seam weld)
10
2. S เปนการบอกขนาดรอยเชื่อม หรือความแข็งแรงรอยเชื่อม หรือขนาดของรูเจาะในกรณี plug weld
11
3. L เปนการบอกความยาวรอยเชื่อม
P เปนการบอกระยะ Pitch รอยเช่ือมจาก center - center
12
4. R เปนการบอกระยะหางของฐานชิ้นงานในกรณี Butt joint
ในกรณี Plug/Slot weld: บอกความลึกของการเชื่อมพอก
A เปนการบอกมุมตัดของชิ้นงานในกรณี
Groove weld
ในกรณี Plug: มุมเช่ือมของรองบาก
3
13
5. เปนสัญลักษณแสดงการเชื่อมโดยรอบ
เปนสัญลักษณแสดงการเชื่อมหนางาน
14
6. (N) เปนการบอกจํานวนของ spot
15
7. T เปนการบอกคุณสมบัติเฉพาะเชนกําหนดวิธีการเชื่อมผิว
เปนสวนทายหากไมมีคุณสมบัติเฉพาะก็ไมตองมีสวนทาย
16
8. เปนการบอกลักษณะของผิวรอยเช่ือมที่ตองการ
F เปนสัญลักษณแสดงวิธีการทําใหไดลักษณะผิวรอยเช่ือมที่ตองการ