Upload
others
View
20
Download
0
Embed Size (px)
Citation preview
EG-Baumusterprüfbescheinigung Certificate of EG type examination
Nr.: TÜV-A-MHF/MG13-06962A
gemäß Richtlinie 2006/42/EG (Maschinen)
according to the Directive 2006142/EC (Machinery)
T� AUSTRIA
Auftraggeber: Sigmatek GmbH & Co. KG Sigmatekstraße 1
Hersteller: Sigmatek GmbH & Co. KG Applicant: Manufacturer: Sigmatekstraße 1
5112 Lamprechtshausen Österreich/ Austria
5112 Lamprechtshausen Österreich/ Austria
Produkt: Zubehör: Gemäß Anhang Product:
,S-DIAS 1/0 System mit internem Bus' ,S-DIAS 110 System with internal Bus' Accessories: According to annex
Typ: Type:
Beschreibung: Description:
Logikeinheiten für Sicherheitsfunktionen Logic units to ensure safety functions
Sicherheitsbezogenes Programmierbares 1/0-System Safety related programmable 110-system
Prüfgrundlagen: Richtlinie 2006/42/EG idgF. und Normen: EN ISO 13849, EN / IEC 62061 Tested according to: Directive 2006142/EC in current version and standards EN ISO 13849, EN / IEC 62061
(Anwendung gemäß Risikobeurteilung / application according to risk assessment)
Bemerkungen: Remarks:
Produkte und Sicherheitskennwerte gemäß Anhang. Products and safety parameters according to annex.
Hiermit bestätigt die TÜV AUSTRIA SERVICES GMBH als Benannte Stelle (ID-Nr. 0408) , dass das oben angeführte Produkt den grundlegenden Sicherheits-Anforderungen der Richtlinie 2006/42/EG entspricht. Grundlage dieser Bescheinigung ist das zur Prüfung vorgelegte Prüfmuster und die technische Dokumentation. Gemäß Artikel 5 und Anhang III ist am Produkt die CE-Kennzeichnung vorgesehen.
Hereby TÜV AUSTRIA SERVICES GMBH certifies as Notified Body (/D-No 0408), that the above mentioned product meets the essential safety requirements of the Directive 2006142/EC. The certificate is based on the fest specimen and the technical documentation subjected to the fest. According to Article 5 and annex III the CE mark is foreseen to be affixed on the product.
Prüfbericht: 13-00055A MFO SIGMATEK SDIAS_int_Bus PB Test report: 13-00055A MFO SIGMA TEK SDIAS_int_Bus PB
14.12.2018 Datum Date
Dipl.-Ing. (FH) Matthias Forkl Benannte Stelle 0408
Notified Body 0408
30.11.2023 Gültig bis
Valid till
Auszugsweise Vervielfältigung nur mit Genehmigung der TÜV AUSTRIA SERVICES GMBH gestattet. Duplication of this document in parts is subject to the approval by TÜV AUSTRIA SERVICES GMBH.
FM-INE-AS-MRL-01 OOb
Revision ·02 vom 12.01.2017
MG13-06962A MFO SIGMATEK_SDIAS_intBus_BB.docx
005408-17-4
TÜV AUSTRIA SERVICES GMBH lndustry and Energy
Anlagen- und Maschinensicherheit
Deutschstraße 10 A-1230 Wien
Tel.: +43 / 5 0454-6202 http://www.tuv.at
Gültigkeit von EG-Baumusterprüfbescheinigungen
1. Erlöschen von Bescheinigungen
Eine Bescheinigung wird auch ohne besondere Mitteilung der TÜV AUSTRIA SERVICES GMBH ungültig, wenn die auf der Bescheinigung angegebene Gültigkeitsdauer abgelaufen ist.
2. Einschränkung, Aussetzung, Ungültigerklärung, Rückzug von Bescheinigungen
Die Bescheinigungen können von der Notifizierten Stelle (TÜV AUSTRIA SERVICES GMBH) mit sofortiger Wirkung eingeschränkt, ausgesetzt oder für ungültig erklärt und zurückgezogen werden, wenn: (a) das bescheinigte Produkt nicht mehr dem genehmigten Muster entspricht, (b) Produkte für Endbenutzer oder Drltte eine Gefährdung darstellen, (c) zum Zeitpunkt der Prüfung Tatsachen nicht oder nicht richtig gesehen und beurteilt worden sind oder auch nicht erkennbar
waren, die einer positiven Bewertung entgegengestanden hätten - hierzu gehört z. B. auch eine fehlerhafte Kategorisierung von Produkten in bestimmte Risikoklassen oder die Einordnung nach Verwendungszweckarten und zwar auch aufgrund eines von der Notifizierten Stelle (TÜV AUSTRIA SERVICES GMBH) zu verantwortenden Fehlers oder Mangels bei der Prüfung,
(d) bei wiederkehrenden Überwachungen, bei Marktkontrollen oder sonst sich nachträglich herausstellenden Produkt- oder Systemmängel, die nicht vom Bescheinigungsinhaber in einer angemessenen Frist abgestellt werden,
(e) der Bescheinigungsinhaber die wiederkehrenden Überwachungstätigkeiten der Notifizierten Stelle (TÜV AUSTRIA SERVICES GMBH) nicht durchführen lässt oder die ordnungsgemäße Durchführung behindert oder einschränkt,
(f) Bescheinigungen oder Kopien von Bescheinigungen geändert und damit gefälscht worden sind, (g) irreführende oder anderweitig unzulässige Werbung mit den Bescheinigungen betrieben wird, (h) fällige Entgelte für die Bescheinigungen und/oder Produkt-Prüfung vom Bescheinigungsinhaber nicht in der gestellten
Frist entrichtet werden.
3. Verfahren zum Bescheinigungs-Entzug
Die Bescheinigung ist im Falle der Ungültigkeitserklärung unverzüglich im Original an die TÜV AUSTRIA SERVICES GMBH zurückzugeben. Der Notifizierten Stelle {TÜV AUSTRIA SERVICES GMBH) wird die Veröffentlichung von Einschränkungen, Aussetzungen, Ungültigkeitserklärungen und Zurückziehungen sowie Löschungen von Bescheinigungen vom Auftraggeber gestattet.
Validity of EC Type Examination Certificates
1. Expiry of certificates
A certificate expires even without special notice by TÜV AUSTRIA SERVICES GMBH when the expiry date specified on the product certificate is reached.
2. Restriction, suspension, cancellation, withdrawal of certificates
Certificates can be restricted, suspended or cancelled and withdrawn with immediate effect by the Notified Body (TÜV AUSTRIA SERVICES GMBH) if: (a) the certified product no longer corresponds to the approved type, (b) products represent a risk for end users or third parties, ( c) facts precluding positive certification were not correctly seen or assessed at the time of the test or were not recognizable - this
also includes e.g. incorrect categorization of products in defined risk classes or the classification according to types of intended uses, also if this is due to an error or fault of the certification for which the Notified Body (TÜV AUSTRIA SERVICES GMBH) is responsible,
(d) defects of the product or of the system are detected in the course of repeated tests, market inspections or in any other way at a later moment and are not eliminated within a reasonable period by the holder of the certificate,
(e) the holder of the certificate omits to have the repeated inspection carried out by the Notified Body (TÜV AUSTRIA SERVICES GMBH) or impedes or restricts its execution in due form,
(f) certificates or copies of certificates were modified and therefore forged, (g) misleading or otherwise inadmissible promotion is made with product certificates, (h) due fees for the certification and/or product test are not paid by the holder of the certificate within the defined period.
3. Certificate withdrawal procedure
lf the certificate is declared invalid, its original copy has to be returned to the Notified Body (TÜV AUSTRIA SERVICES GMBH). The customer authorizes the Notified Body (TÜV AUSTRIA SERVICES GMBH) to publish restrictions, suspensions, cancellations and withdrawals as weil as annulments of certificates.
MG13-06962A MFO SIGMATEK_SDIAS_intßus_BB.docx
1/-�eoitierung 4l!s
Anhang 1 zu EG-Baumusterprüfbescheinigung Nr. TÜV-A-MHF/MG/13-06962A
Annex 1 to certificate of EC type examination No. TÜV-A-MHFIMG/13-06962A �lij � Revision 11
vom / of: 21.11.2019
1so1rEc 1701..<:J
G emäß dem Prüfbericht 13-00055A MF O SIG MATEK SDIAS_int_Bus PB Rev1 . 11 umfasst das oben
genannte Zertifikat die folgenden Produkte:
Based on the test report 13-00055A MFO SIG MA TEK SDIAS_int_Bus PB Rev1. 11 includes the above
mentioned certificate the following products:
CPU Modul
CPU Module
5CP 011
Version
Version
501.01.01
501.02.01
501.03.01
501.04.01
501.05.01
501.06.01
501.07.01
501.08.01
501.09.01
501.10.01
501.11.01
501.12.01
5icherheitsken nwerte
Safety Parameter
PFHo = 1,43E-10 (11h)
5FF = 99,95%
MTTFo = 2689 Jahre
DC = 99%
Für Anwendungen bis PL e, Kategorie 4 gemäß EN ISO 13849-1 oder bis zu einem SIL 3 nach EN / IEC 62061.
For applications up to PL e, category 4 according to EN ISO 13849-1 or until a SIL 3 according to
EN / IEC 62061.
TÜV AUSTRIA SERVICES GMBH
Geschäftsfeld Industrie & Energie
A-1230 Wien, Deutschstraße 10
http ://www. tuv. at 13-06962A MFO SIGMATEK_SDIAS_int_Bus Z-Anhang_Rev11.doc
Seite 1 von 10 Page 1 of 10
TÜV AUSTRIA Deutschland GmbH
Kurze Straße 40, D-70794 Filderstadt Tel.: +49 (0)711 722 336 -0
Fax: +49 (0)711 722 336 -11
Email: [email protected]
Anhang 1 zu EG-Baumusterprüfbescheinigung Nr. TÜV-A-MHF/MG/13-06962A
Annex 1 to certificate of EC type examination No. TÜV-A-MHFIMG/13-06962A
CPU Modul
CPU Module
SCP 111
Revision 11
vom / of: 21.11.2019
Version
Version
S01.01.01
S01.02.01
S01.03.01
S01.04.01
S01.05.01
S01.06.01
S01.07.01
S01.08.01
S01.09.01
S01.10.01
S01.11.01
S01.12.01
S01.13.01
Sicherheitskennwerte
Safety Parameter
PFHo = 1,43E-10 (11h)
SFF = 99,95%
MTTF o = 2689 Jahre
DC = 99%
Für Anwendungen bis PL e, Kategorie 4 gemäß EN ISO 13849-1 oder bis zu einem SIL 3 nach EN / IEC 62061.
For applications up to PL e, category 4 according to EN ISO 13849-1 or until a SIL 3 according to
EN / IEC 62061.
Relais Modul
Relays Module
Safe Digital Relays Module
SRO 021
Version
Version
S01.01.01
S02.01.01
Sicherheitskennwerte
Safety Parameter
including CPU Module SCP 011
PFHo = 9,78E-09 (11h)
SFF = 99,49%
MTTF o = 240 Jahre
DC = 98,99%
Für Anwendungen bis PL e, Kategorie 4 gemäß EN ISO 13849-1 oder bis zu einem SIL 3 nach EN / IEC 62061.
For applications up to PL e, category 4 according to EN ISO 13849-1 or until a SIL 3 according to
EN / /EG 62061.
Anmerkung: Die oben genannte Ausfallswahrscheinlichkeit (PFHo) beruht auf der Annahme, dass das
Ausgangsrelais mit 25.000 Schaltzyklen pro Jahr (nop) betätigt wird.
Remark: The probability of fai/ure per hour (PFHo) mentioned above is based on the assumption that the relays is
activated with about 25.000 switching cycles per year (nop).
TÜV AUSTRIA SERVICES GMBH Geschäftsfeld Industrie & Energie
A-1230 Wien, Deutschstraße 10 http://www.tuv.at 13-06962A MFO SIGMATEK_SD/AS_int_Bus Z-Anhang_Rev11.doc
Seite 2 von 10
Page 2 of10
TÜV AUSTRIA Deutschland GmbH
Kurze Straße 40, D- 70794 Filderstadt
Tel.: +49 (0)711 722 336 - 0 Fax: +49 (0)711 722 336 - 11
Email: [email protected]
eoitierung 4
Anhang 1 zu EG-Baumusterprüfbescheinigung Nr. TÜV-A-MHF/MG/13-06962A
Annex 1 to certificate of EG type examination No. TÜV-A-MHFIMG/13-06962A � �
Eingangsmodul
Input Module
Safe Digital Input Module
SDI 101
1so1r Ec 17010
Revision 11
vom / of: 21.11.2019
Version
Version
S01.01.01
S02.01.01
S03.01.01
Sicherheitskennwerte
Safety Parameter
including CPU Module SCP 011
einkanalige Verwendung/ single channel use
PFHo = 2,23E-09 (11h)
SFF = 99,26%
MTTFo = 1829 Jahre
DC = 96,43%
zweikanalige Verwendung/ dual channel use
PFHo = 2,04E-09 (11h)
SFF = 99,53%
MTTFo = 2297 Jahre
DC = 96,92%
Für Anwendungen bis PL e, Kategorie 4 gemäß EN ISO 13849-1 oder bis zu einem SIL 3 nach EN / IEC 62061.
Bei einkanaliger Verwendung gilt eingeschränkt PL d, Kategorie 2. Aufgrund des hohen S FF>99% bleibt SIL 3 erhalten.
For applications up to PL e, category 4 according to EN ISO 13849-1 or until a SIL 3 according to
EN / IEC 62061. The limitation in application with single· channel use is PL d, category 2. Due to the high
SFF>99% SIL 3 is maintained. 1
Ausgangsmodul Version Sicherheitskennwerte
Safety Parameter Output Module Version
including CPU Module SCP 011
PFHo = 1,09E-09 (11h)
Safe Digital Output Module S01.01.01 SFF = 99,77%
STO 081 S02.01.01 MTTFo = 2053 Jahre
DC = 99%
Für Anwendungen bis PL e, Kategorie 4 gemäß EN ISO 13849-1 oder bis zu einem SIL 3 nach EN / IEC 62061.
For applications up to PL e, EN / IEC 62061.
TÜV AUSTRIA SERVICES GMBH Geschäftsfeld Industrie & Energie
A-1230 Wien, Deutschstraße 10 http://www.tuv.at
category 4 according to EN ISO 13849-1
Seite 3 von 10
Page 3 of 10 13-06962A MFO SIGMATEK_SDIAS_int_Bus Z-Anhang_Rev11.doc
or until a SIL 3 according to
TÜV AUSTRIA Deutschland GmbH
Kurze Straße 40, D- 70794 Filderstadt Tel. : +49 (0)711 722 336 - 0
Fax: +49 (0)711 722 336 - 11 Email: [email protected]
eö\tierung -4
Anhang 1 zu EG-Baumusterprüfbescheinigung Nr. TÜV-A-MHF/MG/13-06962A
Annex 1 to certificate of EC type examination No. TÜV-A-MHFIMG/13-06962A �� �
Absolutwertgeber Modu 1
Absolute Encoder Module
Safe Digital Input Module
SSI 021
1so11Ec 1701.0
Revision 11
vom / of: 21.11.2019
Version
Version
S01.01.01
S01.02.01
S01.03.01
S02.03.01
Sicherheitskennwerte
Safety Parameter
including CPU Module SCP 011
einkanalige Verwendung I single channel use
PFHo = 2,48E-09 (1/h)
SFF = 95,36%
MTTF o = 693 Jahre
DC = 85,10%
zweikanalige Verwendung I dual channel use
PFHo = 2,78E-09 (1/h)
SFF = 99,62%
MTTFo = 677 Jahre
DC = 99%
Für Anwendungen bis PL e, Kategorie 4 gemäß EN ISO 13849-1 oder bis zu einem SIL 3 nach EN / IEC 62061.
Bei einkanaliger Verwendung gilt eingeschränkt PL d, Kategorie 2, beziehungsweise SIL 2.
For applications up to PL e, category 4 according to EN ISO 13849-1 or until a SIL 3 according to
EN / IEC 62061. The limitation in application with single channel use is PL d, category 2, respectively SIL 2.
Schrittmotor-Endstufe Version Sicherheitskennwerte
Stepper Motor Drive Version Safety Parameter
PFHo = 4,99E-08 (1/h)
SFF = 91,92% ST 151 (STO) S01.00.01
MTTFo = 3498 Jahre
DC = 99,12%
Für Anwendungen bis PL e, Kategorie 4 gemäß EN ISO 13849-1 oder bis zu einem SIL 3 nach EN / IEC 62061.
For applications up to PL e, EN / IEC 62061.
TÜV AUSTRIA SERVICES GMBH
Geschäftsfeld Industrie & Energie
A-1230 Wien, Deutschstraße 10 http://www.tuv.at
category 4 according to EN ISO 13849-1
Seite 4 von 10
Page 4 of10 13-06962A MFO S/GMATEK_SDIAS_int_Bus Z-Anhang_Rev11.doc
or until a SIL 3 according to
TÜV AUSTRIA Deutschland GmbH
Kurze Straße 40, D-70794 Filderstadt
Tel. : +49 (0)711 722 336 -0 Fax: +49 (0)711 722 336 - 11
Email: matthias. [email protected]
editierung A
Anhang 1 zu EG-Baumusterprüfbescheinigung Nr. TÜV-A-MHF/MG/13-06962A
Annex 1 to certificate of EG type examination No. TÜV-A-MHFIMG/13-06962A � �
Achsmodul
Axis Module
DC061-xx (STO)
DC061-1 x (STO)
DC062-xx (STO)
Revision 11
vom / of: 21.11.2019
Version
Version
501.01
501.02
501.03
501.01
501.02
501.03
501.04
501.01
501.02
501.03
501.04
1so11Ec 1701°
Sicherheitskennwerte
Safety Parameter
PFHo = 3,92E-10 (1/h)
SFF = 99,89%
MTTFo = 6524 Jahre
DC = 96,09%
Für Anwendungen bis PL e, Kategorie 4 gemäß EN ISO 13849-1 oder bis zu einem SIL 3 nach EN / IEC 62061.
For applications up to PL e, category 4 according to EN ISO 13849-1 or until a SIL 3 according to
EN I IEC 62061.
TÜV AUSTRIA SERVICES GMBH
Geschäftsfeld Industrie & Energie
A-1230 Wien, Deutschstraße 10 http://www.tuv.at 13-06962A MFO SIGMA TEK_SDIAS_int_Bus Z-Anhang_Rev11.doc
Seite 5 von 10
Page 5of10
TÜV AUSTRIA Deutschland GmbH
Kurze Straße 40, D- 70794 Filderstadt
Tel. : +49 (0)711 722 336 - 0 Fax: +49 (0)711 722 336 - 11
Email: [email protected]
eoitierung "1
Anhang 1 zu EG-Baumusterprüfbescheinigung Nr. TÜV-A-MHF/MG/13-06962A
Annex 1 to certificate of EG type examination No. TÜV-A-MHFIMG/13-06962A � �
Eingangs- Ausgangsmodul
Digital Input / Output Module
Safe Digital Input Module
SDM 081
Safe Digital Output Module
SDM 081
1so11Ec 1701Q Revision 11
vom / of: 21.11.2019
Version
Version
S01.01.01
S02.01.01
S03.01.01
Sicherheitskennwerte
Safety Parameter
(including CPU Module SCP 011)
einkanalige Verwendung/ single channel use
PFHo = 2,23E-09 (1/h)
SFF = 99,24%
MTTF o = 1829 Jahre
DC = 96,43%
zweikanalige Verwendung/ dual channel use
PFHo =1,08E-09 (1/h)
SFF = 99,74%
MTTFo = 2053 Jahre
DC = 97,15%
PFHo = 2,20E-09 (1/h)
SFF = 99,53%
MTTFo = 1901 Jahre
DC = 97,28%
Für Anwendungen bis PL e, Kategorie 4 gemäß EN ISO 13849-1 oder bis zu einem SIL 3 nach
EN / IEC 62061. Für die Eingänge gilt bei einkanaliger Verwendung eingeschränkt PL d, Kategorie 2.
Aufgrund des hohen SFF>99% bleibt SIL 3 erhalten.
For applications up to PL e, category 4 according to EN ISO 13849-1 or until a SIL 3 according to
EN / IEC 62061. For the inputs with single channel application, the limitation is PL d, category 2. Due to the
high SFF>99% SIL 3 is maintained.
TÜV AUSTRIA SERVICES GMBH Geschäftsfeld Industrie & Energie A-1230 Wien, Deutschstraße 10
http://www. tuv.at 13-06962A MFO S/GMATEK_SDIAS_int_Bus Z-Anhang_Rev11.doc
Seite 6 von 10
Page 6 of 10
TÜV AUSTRIA Deutschland GmbH
Kurze Straße 40, D- 70794 Filderstadt Tel.: +49 (0)711 722 336 - 0
Fax: +49 (0)711 722 336 - 11
Email: [email protected]
editierung 4
Anhang 1 zu EG-Baumusterprüfbescheinigung Nr. TÜV-A-MHF/MG/13-06962A
Annex 1 to certificate of EG type examination No. TÜV-A-MHFIMG/13-06962A � �
Inkrementalgeber Modul
lncremental Encoder Module
Safe Digital Input Module
SNC 021
1so11Ec 1101..0 Revision 11
vom / of: 21.11.2019
Version
Version
502.02.02
Sicherheitskennwerte
Safety Parameter
including CPU Module SCP 011
einkanalige Verwendung/ single channel use
PFHo = 3,42E-09 (1/h)
SFF = 99,57%
MTTFo = 803 Jahre
DC = 97,82%
zweikanalige Verwendung / dual channel use
PFHo = 3,51 E-09 (1/h)
SFF = 99,63%
MTTFo = 580 Jahre
DC = 99%
Für Anwendungen bis PL e, Kategorie 4 gemäß EN ISO 13849-1 oder bis zu einem SIL 3 nach EN / IEC 62061.
Bei einkanaliger Verwendung gilt eingeschränkt PL d, Kategorie 2. Aufgrund des hohen SFF>99% bleibt SIL 3 erhalten.
For applications up to PL e, category 4 according to EN ISO 13849-1 or until a SIL 3 according to
EN / IEC 62061. The limitation in application with single channel use is PL d, category 2. Due to the high
SFF>99% S/L 3 is maintained.
TÜV AUSTRIA SERVICES GMBH
Geschäftsfeld Industrie & Energie
A-1230 Wien, Deutschstraße 10
http://www. tuv.at 13-06962A MFO SIGMATEK_SDIAS_int_Bus Z-Anhang_Rev11.doc
Seite 7 von 10
Page 7 of10
TÜV AUSTRIA Deutschland GmbH
Kurze Straße 40, D- 70794 Filderstadt Tel.: +49 (0)711 722 336 -0
Fax: +49 (0)711 722 336 - 11
Email: matthias. [email protected]
<eöitierung -'!
Anhang 1 zu EG-Baumusterprüfbescheinigung Nr. TÜV-A-MHF/MG/13-06962A
Annex 1 to certificate of EG type examination No. TÜV-A-MHFIMG/13-06962A �� �
Eingangsmodul
Input Module
Safe Digital Input Module
518 061
1so11E c 17010
Revision 11
vom / of: 21.11.2019
Version
Version
501.01
Sicherheitskennwerte
Safety Parameter
including CPU Module SCP 011
einkanalige Verwendung/ single channel use
PFHo = 1,01E-09 (1/h)
SFF = 99,84%
MTTF o = 840 Jahre
DC = 99%
zweikanalige Verwendung/ dual channel use
PFHo = 1,45E-09 (11h)
SFF = 99,82%
MTTFo = 856 Jahre
DC = 99%
Für Anwendungen bis PL e, Kategorie 4 gemäß EN ISO 13849-1 oder bis zu einem SIL 3 nach EN / IEC 62061.
Bei einkanaliger Verwendung gilt eingeschränkt PL d, Kategorie 2. Aufgrund des hohen SFF>99% bleibt SIL 3 erhalten.
For applications up to PL e, category 4 according to EN ISO 13849-1 or until a SIL 3 according to
EN /!EG 62061. The limitation in application with single channel use is PL d, category 2. Due to the high
SFF>99% SIL 3 is maintained.
TÜV AUSTRIA SERVICES GMBH
Geschäftsfeld Industrie & Energie
A-1230 Wien, Deutschstraße 10
http://www. tuv.at 13-06962A MFO S/GMATEK_SDIAS_int_Bus Z-Anhang_Rev11.doc
Seite 8 von 1 O Page 8of10
TÜV AUSTRIA Deutschland GmbH
Kurze Straße 40, D- 70794 Filderstadt Tel. : +49 (0)711 722 336 -0
Fax: +49 (0)711 722 336 - 11
Email: matthias. [email protected]
eoitierung 4
Anhang 1 zu EG-Baumusterprüfbescheinigung Nr. TÜV-A-MHF/MG/13-06962A
Annex 1 to certificate of EG type examination No. TÜV-A-MHFIMG/13-06962A �� �
Produkt
Product
LASAL Safety
Designer
Programmier-Tool
LASAL Safety Designer
Programming tool
Revision 11
vom / of: 21.11.2019
1so11Ec 17020
Build Version I Sicherheitskennnummer
Build Version / Safety Number
1155 1. 1.7
1156 1. 1.7
1181 1. 1.8
1187 1.1.9 (equal 1.1.8)
1239 01. 01.013
1317 01. 01.015
1353 01. 01.030
1446 01.01. 032
1496 01. 01.034
1584 01.01.036
1616 01.01. 038
1658 01. 01. 040
1709 01.01.044
1724 01. 01.046
1748 01.01. 048
1767 01. 01. 050
1808 01. 01. 052
1827 01. 01. 054
2060 01. 01.056
2231 01. 01.058
Für Anwendungen bis PL e, Kategorie 4 gemäß EN ISO 13849-1 oder bis zu einem SIL 3 nach EN / IEC 62061.
For applications up to PL e, category 4 according to EN ISO 13849-1
EN I IEC 62061.
TÜV AUSTRIA SERVICES GMBH
Geschäftsfeld Industrie & Energie
A-1230 Wien, Deutschstraße 10
http://www.tuv.at 13-06962A MFO S/GMATEK_SDIAS_int_Bus Z-Anhang_Rev11.doc
Seite 9 von 10 Page 9of10
or until a SIL 3 according to
TÜV AUSTRIA Deutschland GmbH
Kurze Straße 40, D- 70794 Filderstadt Tel.: +49 (0)711 722 336 - 0
Fax: +49 (0)711 722 336 -11
Email: matthias.forkl@tuv. at
Anhang 1 zu EG-Baumusterprüfbescheinigung Nr. TÜV-A-MHF/MG/13-06962A
Annex 1 to certificate of EG type examination No. TÜV-A-MHFIMG/13-06962A � � Revision 11
vom / of: 21.11.2019
Dipl.-Ing. (FH) Matthias Forkl
Maschinen- und G erätesicherheit Machine and equipment safety
1so11Ec 170?..IJ
Auszugsweise Vervielfältigung nur mit Genehmigung der TÜV AUSTRIA SERVICES GMBH gestattet. Duplication of this document in parts is subject to the approval by TÜV AUSTRIA SERVICES GMBH.
TÜV AUSTRIA SERVICES GMBH
Geschäftsfeld Industrie & Energie
A-1230 Wien, Deutschstraße 10 http://www.tuv.at 13-06962A MFO SIGMA TEK_ SDIAS_int_Bus Z-Anhang_Rev11. doc
Seite 10 von 10
Page 10 of 10
TÜV AUSTRIA Deutschland GmbH
Kurze Straße 40, D- 70794 Filderstadt Tel.: +49 (0)711 722 336 - 0
Fax: +49 (0)711 722 336 -11
Email: [email protected]