Upload
others
View
4
Download
1
Embed Size (px)
Citation preview
a little (theory): emulsion stability
Klaus TauerMPI Colloids and Interfaces
Am Mühlenberg, D-14476 Golm, Germany
Emulsions – Part 2
topics:
surfactant properties
degradation of emulsions
phase separation
Ostwald ripening
aggregation
phase inversion
(some) thermodynamics
S
ST
TU ⎟⎠⎞
⎜⎝⎛∂σ∂
−σ=
If two components are completely compatible they do not form an interface as it is the case for dilute gases or two mutually soluble liquids. In this case, the free energy of mixing is negative.
It is exactly the opposite if two incompatible components forming an interface upon mixing. If a stable interface is formed the free energy of formation must be positive.
This behavior finds its expression in a special form of the Gibbs-Helmholtzequation where US is the total surface energy for a given interface (S), σ is the interfacial tension, and T is the absolute temperature .
0Tσ∂⎛ ⎞ <⎜ ⎟∂⎝ ⎠
for most systems
Some Thermodynamics (emulsion formation by comminution)
The preparation of emulsions requires energy to disperse the organic phase (solvent or solution) in water.
In order to get an idea about the thermodynamics the change in the Gibbs free energy of the system (∆G), provided by the particular dispersing procedure at constant composition and pressure, can be expressed by:
STHG ∆⋅−∆=∆
The entropy (∆S) is a measure of the extent of disorder in the system and hence measures the extent of size reduction of the organic phase (or increase in droplet number). The increasing disorder during the formation of an emulsion means a positive ∆S contributing to stability.
∆H is the enthalpy of the system and can be considered as the binding energy of the organic bulk material or the energy input needed to achieve a certain average droplet size.
Some Thermodynamics (2)
∆W is the free energy of the interface and corresponds to the reversible work brought permanently into the system during the emulsification process . This makes an emulsion very prone to coalescence processes which lead to a decrease in ∆A and subsequently in ∆W. The conclusion is straightforward that ultimate stability against coalescence processes is only achieved if σapproaches zero.
AW ∆⋅σ=∆
If a volume change during the emulsification is neglected the enthalpy corresponds to the internal energy which is the sum of the work required to expand the interfacial area (∆W) and an amount of heat which results from wasting a part of the energy input .
The increase in the energy of an emulsion compared to the non-emulsified components is equal to ∆W. This amount of energy can be considered as a measure of the thermodynamic instability of an emulsion.
Some Thermodynamics (3)
containerinterface 1/C
surface liquid/vaporinterface 1/S
interface ½(macrodrops)
unmixed (u) state of components 1 and 2(continuous phase: 1 and dispersed phase: 2)
Some Thermodynamics (4)
G1, G2 bulk properties
in many cases but not always
!1 12u uSG G<<
in almost all cases G1C is not considered !
1 2 12 1 1
12 12 12
1 1
1 1
u u uS C
u u
uS S S
C C C
G G G G G G
G A
G AG A
σ
σσ
= + + + +
= ⋅
= ⋅
= ⋅u121S AA <<
mixed state of components 1 and 2(continuous phase: 1 and dispersed phase: 2)
Some Thermodynamics (5)
interface 1/2Interfacial tension: σ12
1 2 12 1 2
12 12 12
( )m mC C
m m
G G G G G G T S
G Aσ
= + + + + − ⋅ ∆
= ⋅
configurationalentropy
Some Thermodynamics (6)
free energy of emulsion formation between components 1 and 2(continuous phase: 1 and dispersed phase: 2)
if σ12 extremely low spontaneous emulsification!
0formG∆ >>
12mA T Sσ ⋅ ∆ >> ⋅ ∆in general:
requires externalenergy
12m u m
formG G G A T Sσ∆ = − = ⋅ ∆ − ⋅ ∆
Some Thermodynamics (7)
free energy of emulsion breakdown between components 1 and 2(continuous phase: 1 and dispersed phase: 2)
!
if 0formG∆ >>
Action of Emulsifiers
main actions:
reducing the interfacial tension between the phases
forming a barrier between the phases
Action of Emulsifiers
- promoting the formationof an emulsion,
- making it easier to prepare, - producing finer droplet size, - aiding stability to the dispersed
state
controlling the type of emulsion that is to be formed: oil in water (O/W) or water in oil (W/O)
Gibbs - Marangoni Effect convective motions due to differences in interfacial tension
local differences in s at curved interfaces try to restore flat surface spontaneously
Additional action of surfactants: generation and maintaining of a gradient of the interfacial tension (gradient of the interfacial density of surfactant molecules) across the droplet surface during undulations caused by thermal or mechanical stresses. The lattereffect also contributes to the stability of emulsions and is strongly connected with the Gibbs - Marangoni effect
(1)
Gibbs - Marangoni Effect (2)
A closer look at an emulsion droplet (O/W)
liquid crystalline surfactant film
monomolecular surfactant film
polymeric surfactant film (tail-loop-train model)
Bancroft‘s rule
*W. D. Bancroft J. Phys. Chem. 16 (1912) 177-233
„When water is the dispersing phase, the emulsifying agent shouldbe a hydrophilic colloid (Höber). Höber does not draw the conclusion that the emulsifying agent should be an oleophile colloid in case the emulsion is to contain water in drops“*
The liquid in which the stabilizer has a higher solubility forms the continuous phase.
Classification of surface-active agents by HLBHLB - hydrophilicity lipophilicity balance*
*W. C. Griffin J. Soc. Cosmetic Chemists 1 (1949) 311-326
HLB-values of typical food emulsifiers
HLB – pros and consPositives
Excellent starting pointGenerally produces a fairly good emulsion
NegativesIgnores the importance of:
• Electrical double layer• Temperature effects of ethoxylates• Fatty alcohols• Placement of emulsifier• % of emulsifier to be used• Phase volume ratios• Component interactions• Liquid crystals
P. D. T. Huibers, D. O. Shah Langmuir 13 (1997) 5762-6765
HLB value is important also for the stability of an emulsion
the surfactant must be present at the interface - optimum HLB is necessary
surfactant properties (1) – Krafft temperature
solubility
cmcW. L. Friedrich E. Krafft(1852-1923), Heidelberg
anionic surfactant
Krafft Temperature - Examples
CH3 (CH2)10 CH2 OSO3-Na+ CH3 (CH2)16 CH2 OSO3
-Na+
Phase Inversion Temperature PITAs the temperature increases, the water solubilityof ethoxylated nonionic emulsifiers becomespoorer (the HLB decreases). There is a temperature (PIT) at which the hydrophilic and lipophilic characteristics of the emulsifier are equal (relative to the required HLBof the oil phase). At this temperature the emulsion will exhibit a phase inversion.The PIT should be at least 20 °C higher than thestorage temperature. Choose emulsifiers, and concentrations, to raise the PIT.
Phase inversion temperature (PIT)
H2O
Emulsifiers may be selected by means of the HLB scale or by the phase-inversion temperature (PIT)
Requested Breakdown of Emulsions: Demulsification
Yes, sometimes but not always when needed and not completely
Important examples:
oil recovery (oil in water emulsions) waste treatment (oil in water emulsions)
destroy the interfacial surfactant layer by demulsifiers
topic in its own right
There are several strategies for counteracting emulsions:
•air flotation, ozonation or other oxidations
•modifying the surfactant's charge (addition of CaCI2 or MgS04changes surfactant solubility)
•Antagonist addition (charge neutralization)
•Increase the solubility of the surfactant in either bulk phase ( alcohol orother polar solvents, such as acetone to pull the surfactant out of the oil phase)
•If the aqueous phase is a brine, dilution with water might help
•Disrupt the oriented structure of the emulsifier's interfacial phase with demulsifiers which are materials not very soluble in either phase andhence concentrate at the interface (separation due to increasing theintermolecular distance and weakening the binding forces constructed by the emulsifier)
•Increase the ionic strength
Degradation of Emulsions
1
1
2
3
3
3
3
4
1 – phase separation
(creaming, sedimentation)
2 – Ostwald ripening
3 – aggregation processes
(flocculation, coagulation, coalescence)
4 – phase inversion
Phase separationstationary velocity for laminar conditions during phase separation:
The density of the disperse phase means exactly the density of the droplets during the motion. A moving droplet is composed of liquid-1, stabilizers, and in some cases also a certain amount of continuous phase which is entrapped in a layer surrounding the droplets.
( )c
2d
cdps 18gDV
ηρρ
⋅⋅−=
As a rule of thumb: Dd > 1 µm sedimentation and creaming for ρd > ρc and ρd < ρc
Dd < 1 µm: water and a common monomer / oil, Brownian motion keeps the droplets almost evenly distributed throughout the emulsion (if no other forces are acting)
phase separation depends on density difference
Phase Separation: Dispersed Phase
( )ρ ρd c∆ = −
sedimentation∆ = 0.49845 g cm-3
creaming∆ = -0.3452 g cm-3
chloroform / water hexane / water
oil
oil
phase separation is size dependent Dd2
Phase Separation: Dispersed Phase
practical meaning: bimodal droplet size distributions
natural fresh milk, non homogenized:
butter &cheese
Phase Separation: Continuous Phase
phase separation is viscosity dependent1/ηc
to reduce phase separation:
add gelling agents to increase viscosity of the continuous phase
Aggregation Processes
0
dPP
V int
/ k B
T
secondary minimum(Vsm < 1,5 kBT for reversible flocculation)
primary minimum(ca. 2 times dispersions energy droplet - H2O)
primary maximum (Vpm > 15 kBT)
Born repulsionDLVO theory for charged spheres
electrostatic double layer repulsion competes with van der Waalsattraction
Derjaguin B.V., Landau L.D., Theory of the stability of strongly charged lyophobic sols and the adhesion of strongly charged particles in solutions of electrolyteActa Physicochimica URSS 14 (1941) 633-662Verwey E.J.W., Overbeek J.Th.G., 1948, Theory of the Stability of Lyophobic Colloids. Elsevier, New York
E J W Verwey; J Th G Overbeek; K van Nes Publisher: New York, Elsevier Pub. Co., 1948. Theory of the stability of lyophobic colloids; the interaction of sol particles having an electric double layer
electrokinetic potential (zeta potential) is directly accessible by electrophoretic measurements
surface potential is directly accessible by charge titration
coalescence is not a single stage process but
comprises at least four elementary steps:
• contact at a distance that allows aattractive interaction, • the drainage of the continuous phasefilm between the drops,
• the rupture of the film, • the collapse of the droplets.
nowadays aggregation processes can be prevented very effectively
Aggregation Processes
Common and Newton Black Films –Visualization of DLVO forces
movies H-J- Müller, KGF, IF
Continuous Phase Film Stability:
Light is reflected from each side of the film. These two contributions interfere in the familiar manner to give the colors of thin films by removing certain colors by destructive interference, just as seen in oil films and in the oxide films on tempered steel.
When the film thickness becomes less than about 1 µm the colors begin to appear, at first green and magenta, then the brighter colors of lower orders, including reds, blues and one good yellow or straw color.
At about 0.1 µm there is a white, but for thinner films the color approaches black (film invisible) as the light from front and back cancel.
These colors serve to indicate the thickness of the films.
film thinning
(hard) sphere packing problem
Experiment shows that dropping the spheres in randomly will achieve a density of around 65%.
However, a higher density can be achieved by carefully arranging the spheres as follows. Start with a layer of spheres in a hexagonal lattice, then put the next layer of spheres in the lowest points you can find above the first layer, and soon - this is just the way you see oranges stacked in a shop.
This natural method of stacking the spheres creates one of two similar patterns called cubic close packing and hexagonal close packing. Each of these two arrangements has an average density of ~74 %.
The Kepler conjecture says that this is the best that can be done - no other arrangement of spheres has a higher average density than this.
The sphere packing problem has frustrated mathematicians for nearly four centuries.
Kepler‘s Conjecture(1571 – 1630)
highest possible volumeoccupied by solid spheres =
maxπφ 74%18
≈ ≈
monolayer formed from a 10 µm diameter monodisperse
emulsion of silicone oil in waterLangmuir 2000, 16, 347-351
Macromolecules 2003, 36, 648-653
highly swollen PS particles(styrene, 1-chlorododecane)
entropic swelling
Highly Concentrated Emulsions: maxφ >74%
rhomboidal dodecahedron
packing from 74% to 94% internal phase volume
tetrakaidecahedron
packing above 94% internal phase volume
Transition from Spheres to Polyhedrons:
Concentrated Emulsions a Practical Example:
HIPE: high internal phase emulsionsThe most studied system: w/o emulsion with styrene / divinylbenzenemixture as continuous phase and water as internal phase with a nonionic surfactant; polymerization with oil and water soluble initiators leads to polymer foam with open-cellular structure
Adv. Polym. Sci. 126 (1996) 163-214
Stabilization against flocculation is nowadays no issue anymore
Phase Inversion
phase inversion depends on:
• the polarity of the oil phase, • the kind of electrolyte and its concentration, • other additives (organic, water-soluble solvents increasing oil solubility in water),• the oil volume fraction.
important in the case of polymeric surfactants with a stabilizing moiety possessing a critical solution temperature
poly(ethylene glycol) based surfactants
temperature increases HLB decreases of the surfactant and it may subsequently, in accordance with Bancroft’s rule lead to stabilization of a water in oil instead of an oil in water emulsion.
Ostwald Ripening (OR)a direct consequence of the polydispersity of the DSD whereby even thermal fluctuation in Dd or in the curvature may cause it
( ) 14
,ln lnmB B
d
vk T C D k T CDσ
∞⋅ ⋅
⋅ = + ⋅
chemical potential of a dispersed phase compared to that of the same bulk material
concentration of the disperse phase just at the interface (C(D) where σ holds)
C∞,1 being the solubility of the disperse (C1) phase in the continuous medium
two important points:
Ostwald ripening requires to occur a certain solubility of the dispersed phase (C1) in the continuous phaseDirect contact between the droplets is not necessary as molecular diffusion through the continuous phase leads to an increase in Dd
OR is a topic in its own right
water solubility (v/v)
OR – continued 1
Higuchi, W. I. and J. Misra, Physical degradation of emulsions via the molecular diffusion route and the possible prevention thereof, J. Pharmaceutical Sci., 51, 459 - 466 (1962)
Kabalnov, A. S., A. V. Pertzov and E. D. Shchukin, Ostwald ripening in two-component disperse phase systems: application to emulsion stability, Coll. Surf., 24, 19 - 32 (1987)
it might be possible to stabilize emulsions against Ostwald ripening by addition of small amounts of a third component (compound- 2) which preferentially should dissolved in liquid-1 and not in the continuous phase
this was done by Higuchi and Misra and experimentally verified by stabilization of carbon tetrachloride emulsion in water with hexadecane
Ostwald ripening in the presence of compound-2 was theoretically investigated by Kabalnov et al.
OR – continued 2
a zero solubility = a very low solubility !!!
hexadecane emulsions degrade (slowly) via OR ! !
properties of Compound- 2 are crucial
02 =∞,C12 ,, ∞∞ <<CC
OR – continued 3
which means that the total number of droplets remains constant.
situation at equilibrium (subscript e) regarding the second component (subscript 2) for two particles (superscripts ‘ and ‘’) with different diameters.
However, the distribution of liquid-1 from small to large particles changes the composition of the droplets. It increases the volume fraction of compound-2 (φ2) in the smaller particles and decreases it in the larger ones.Indeed, investigations on Ostwald ripening with sedimentation field-flow fractionation in fluorocarbon emulsions confirmed the theoretical prediction that compound-2 is enriched in smaller drops [Weers, J. G. and R. A. Arlauskas, Langmuir, 11, 474 - 477 (1995) ].
''e,dB
1,m''e,2'
e,dB
1,m'e,2
D1
Tkv4
D1
Tkv4
⋅⋅σ
−φ=⋅⋅σ
−φ
02 =∞,C
OR – continued 4
i,d_
B
1,mi,2
DTk3
v4
⋅
⋅σ>φ
To compensate for the Ostwald ripening requires φ2-values depending on the droplet size in the sense that smaller drops require a higher φ2and vice versa. However, this is practically impossible to control during the initial emulsification process.
from the chemical potential at equilibrium follows a condition for φ2,i that the system can reach the equilibrium and Ostwald ripening will stop. Here the subscript i stands for initial conditions and stands for the initial average droplet size
If this condition is not met the particles cannot reach equilibrium and Ostwald ripening will further increase the differences in the chemical potential for particles with different sizes.
OR – continued 5
An additional effect arises if compound-2 is surface active. During the equilibration of liquid-1 σ decreases in the small drops and increases in the large ones. This decreases the driving force for the re-distribution of liquid-1 and hence would additionally stabilize the emulsion against Ostwald ripening.
the addition of a completely water-insoluble hydrophobe during the emulsification does not per se prevent Ostwald ripening.
Ostwald ripening takes place in any case, except an exactly monodisperse droplet size distribution
it will either lead to an equilibrium after a certain maturation time or not (i.e., indefinitely ripening until phase separation is completed)
Emulsions either natural or man-made are essential parts of life on earth:
foodcosmetic
constructionhealth caremedicine
information techn.
biology
materialspaved surfaces
see you next week:
µ-emulsions & miniemulsions