Click here to load reader

Enrollment & Course Schedules - Delaware Skills · PDF fileEnrollment & Course Schedules Cycle 1 Cycle 2 Cycle 3 ... enrollment in any Level One Module Level Two SMAW, ... score of

  • View
    212

  • Download
    0

Embed Size (px)

Text of Enrollment & Course Schedules - Delaware Skills · PDF fileEnrollment & Course...

  • 1

  • 2

    Enrollment & Course Schedules

    Cycle 1 Cycle 2 Cycle 3 Level 1

    Recruitment: August 5, 6, 7 2014

    Arrive by: 8:30 AM for testing

    Open enrollment August 5, 2014 - August 20, 2014 by appointment

    Classes begin August 26, 2014 November 18, 2014

    Tuesdays/Thursdays at 6:00 PM 9:00 PM

    Recruitment: December 10, 11, 12 2014

    Arrive by: 8:30 AM for testing

    Open enrollment September 9, 2014 December 9, 2014 by appointment

    Classes begin January 6, 2015 March 26, 2015

    Tuesdays/Thursdays at 6:00 PM 9:00 PM

    Recruitment: March 10, 11, 12 2015

    Arrive by: 8:30 AM for testing

    Open enrollment January 12, 2015 March 9, 2015 by appointment

    Classes begin April 14, 2015 July 2, 2015

    Tuesdays/Thursdays at 6:00 PM 9:00 PM

    Level 2

    Recruitment: August 5, 6, 7 2014

    Arrive by: 8:30 AM for testing

    Open enrollment August 5, 2014 - August 20, 2014 by appointment

    Classes begin August 26, 2014 November 18, 2014

    Tuesdays/Thursdays at 6:00 PM 9:00 PM

    Recruitment: December 10, 11, 12 2014

    Arrive by: 8:30 AM for testing

    Open enrollment September 9, 2014 December 9, 2014 by appointment

    Classes begin January 6, 2015 March 26, 2015

    Tuesdays/Thursdays at 6:00 PM 9:00 PM

    Recruitment: March 10, 11, 12 2015

    Arrive by: 8:30 AM for testing

    Open enrollment January 12, 2015 March 9, 2015 by appointment

    Classes begin April 14, 2015 July 2, 2015

    Tuesdays/Thursdays at 6:00 PM 9:00 PM

    Level 3

    Recruitment: August 5, 6, 7 2014

    Arrive by: 8:30 AM for testing

    Open enrollment August 5, 2014 - August 20, 2014 by appointment

    Semester 1: August 27 November 12, 2014

    Semester 2: January 7 April 1, 2014

    n/a

    n/a

    *Note:

    1. Recruitment on site at the Delaware Skills Center

    2. Level 3 Courses consists of two 72 hour semesters for a total of 144 hours training

    3. Call (302)-654-5392 for an appointment

  • 3

    The Following are course requirements/prerequisites for acceptance in the Welding Career

    Lattice Modules:

    Level One SMAW, GMAW, and GTAW require completion of one or more of the basic

    training experience pre-requisites for enrollment

    Students that have completed one or more of the Level One modules are eligible for

    enrollment in any Level One Module

    Level Two SMAW, GMAW, and GTAW require completion of one or more of the basic

    training or experience pre-requisites as well as completion of the TABE Test and

    score of 10th grade or higher.

    Students that have completed the basic training or experience pre-requisite

    requirements are eligible to enroll in all Level One Modules, however they are

    limited to enrollment in one module per training cycle

    Students that have completed the basic training or experience pre-requisite

    requirements and score at a 10th grade or higher level on the TABE Test are eligible

    to enroll in all Level Two modules, however they are limited to enrollment in one

    module per training cycle

    Students must complete the Level One or Level Two pre-requisite Training Module

    to enroll in Level Three Training Modules

    The Following qualify for training/experience basic enrollment requirements for all

    Welding Career Lattice Modules:

    Graduates of the Delaware Skills Center Basic Welding program

    Graduates of other Basic Welding Programs from other training providers

    Employees from traditional and non-traditional employers seeking training for

    specific Welding skill set

    Employees currently employed seeking career advancement through specialized

    skills training

    Students seeking employment that need additional skills training for employment

    that meet program requirements

  • 4

    Welding Career Lattice

    Level One

    Modules 1-2-3

    Level One training modules are for students that do not meet the literacy and numeracy

    requirements for Level Two courses or for students that would like to improve numeracy

    and literacy skills to improve their employment opportunities and advancement. The Level

    One course consists of 72 hour of classroom and practical welding instruction and

    simulated work experience. The duration of Level One courses may vary based on literacy

    and numeracy training and requirement completion. The training hours will vary

    depending on the student TABE scores for this portion of the Level One course

    requirements. Students will be given the TABE test to determine numeracy and literacy

    gains. When a student achieves adequate gains based on TABE level improvements, they

    will exit numeracy/literacy training and complete the reminder of the 72 hours of Welding.

    Training will take place Mon/Wed or Tues/Thurs from 6:00pm 9:00pm. Students will

    attend numeracy/literacy training from 6:00pm to 7:00pm and occupational skills training

    (Welding) from 7:00pm to 9:00pm

    Module #1

    72-hour GMAW Welding

    o Safety Review 5 Hours

    Explain the appropriate Safety precautions to take around common job-site

    hazards

    Demonstrate the use and care of appropriate personal protective equipment (PPE)

    Describe safe behavior on and around ladders and scaffolds

    Explain the importance of Hazard Communications (HazCom) and material

    safety data sheets (MSDS)

    o Equipment Familiarization and Setup 2.5 Hours

    Explain the use of various types of equipment used for GMAW Welding

    Familiarization of equipment Controls and Adjustments on Equipment used for

    GMAW Welding

    o Types of Gasses and Filler Metals (Wire) 2.5 Hours

    Explain the different types and mixtures of Gasses used for GMAW Welding

    Explain the different types of Filler Metals (Wire) used for GMAW Welding

    o Proper Welding Techniques for GMAW Fillet Welds - 2.5 Hours

    Proper Methods for quality GMAW Fillet Welds

    o GMAW Welding Positions for Welding - 2 Hours

    Discussion and examples of 1F, 2F, 3F and 4F

    o GMAW Weld Quality and Inspection - 5 Hours

  • 5

    Explains how to identify High Quality GMAW Welds

    Explains the Inspection Process for Determining GMAW Weld Quality

    o GMAW 1F Fillet Welds - 12.5 Hours

    Practice GMAW 1F Fillet Welds

    o GMAW 2F Fillet Welds - 12.5 Hours

    Practice GMAW 2F Fillet Welds

    o GMAW 3F Fillet Welds - 12.5 Hours

    Practice GMAW 3F Fillet Welds

    o GMAW 4F Fillet Welds 12.5 Hours

    Practice GMAW 4F Fillet Welds

    Module #2

    72-hour SMAW Welding

    o Safety Reviews 5 Hours

    Explain the appropriate safety precautions to take around common job-site

    Demonstrate the use and care of appropriate personal protective equipment (PPE)

    Describe safe behavior on and around ladders and scaffolds

    Explain the importance of Hazard Communications (HazCom) and material

    safety data sheets (MSDS)

    o Equipment Familiarization and Setup - 2.5 Hours

    Explain the use of various types of equipment used for SMAW Welding

    Familiarization of Equipment Controls and Adjustments on Equipment

    used SMAW Welding

    o Types of Filler Metals (Rods) - 2.5 Hours

    Explain the different types of Filler Metals (Rod) used for SMAW

    Welding

    o Proper Welding Techniques for SMAW Fillet Welds - 2.5 Hours

    Proper Methods for quality SMAW Fillet Welds

    o SMAW Welding Positions for Fillets Welds - 2.5 Hours

    Discussion and Examples of SMAW 1F, 2F, 3F, and 4F SMAW Welds

    o SMAW Weld Quality and Inspection -5 Hours

    Explains how to identify High Quality SMAW Welds

    Explains the Inspection Process for determining SMAW Weld Quality

    o Preparation and Setup for SMAW Pipe Welding - 12 Hours

    Explains how to prepare Pipe for SMAW Welding

    Explains how to setup Pipe for SMAW Welding

    o SMAW 1G Groove Pipe Welds - 20 Hours

    Practice 1G SMAW Groove Pipe Welds

    o SMAW 2G Groove Pipe Welds 20 Hours

    Practice 2G SMAW Groove Pipe Welds

  • 6

    Module #3

    72-hour GTAW Welding

    o Safety Reviews 5 Hours

    Explain the appropriate safety precautions to take around common job-site

    Demonstrate the use and care of appropriate personal protective equipment (PPE)

    Describe safe behavior on and around ladders and scaffolds

    Explain the importance of Hazard Communications (HazCom) and material

    safety data sheets (MSDS)

    o Equipment Familiarization and Setup - 2.5 Hours

    Explain the use of various types of equipment used for GTAW Welding

    Familiarization of Equipment Controls and Adjustments on Equipment

    used GTAW Welding

    o Types of Gasses and Filler Metals - 2 Hours

    Explain the different types of mixtures of Gasses used for GTAW welding

    Explain the different types of Filler Metals (Wire) used for GTAW

    welding

    o Proper Welding Techniques for GTAW Fillet Welds - 2.5 Hours

    Proper Methods for quality GTAW Fillet Welds

    o GTAW Welding Positions for Fillets Welds - 2.5 Hours

    Discussion and Examples of 1F, 2F, 3F, and 4F GTAW Welds

    o GTAW Weld Quality and Inspection -5 Hours

    Explains how to identify High Quality GTAW Welds

    Explains the Inspection Process for determining GTAW Weld Quality

    o GTAW 1F Fillet Welds - 12.5 Hours

    Practice GTAW 1F Fillet Welds