Hardware - Camara Ubiquiti AirCam_QSG

7/26/2019 Hardware - Camara Ubiquiti AirCam_QSG

1/28

Security Camera


2/28


3/28

1

Introduction

Introduction

Thank you for purchasing the airCam. This Quick Start Guide isdesigned to guide you through the installation of the airCam and

show you how to access the airCam's configuration interface. ThisQuick Start Guide also includes the warranty terms.

The airVisionsoftware and User Guide are available for downloadat downloads.ubnt.com/airvision.

The hardware installation process is different for indoor andoutdoor installations. After familiarizing yourself with the

airCam in the Hardware Overviewsection, please proceed to theappropriate installation section:

"Outdoor Installation" on page 4

"Indoor Installation" on page 8

Package Contents

Camera Mounting Bracket 24V PoE Adapter Power Cord

Security Camera

Seal Self-TappingScrews (Qty. 3)

Screw Anchors(Qty. 3)

Quick Start Guide

Installation Requirements

Pencil

Drill and 6mm drill bits

TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the customers responsibility tofollow local country regulations, including operation within legal frequency channels, output power,

indoor cabling requirements, and Dynamic Frequency Selection (DFS) requirements.


4/28

2

airCam

Hardware Overview

Front

Sun Shade

Lens

remove plastic lens film

before use


5/28

3

Hardware Overview

Back

Plug

(for outdoor installations)

Ethernet Door

Mounting Slots

LEDs

Power The Power LED will light steady orange when theairCam is connected to a power source.

Ethernet The Ethernet LED will light steady green whenan active Ethernet connection is made and flash whenthere is activity.


6/28

4

airCam

Installation Overview

The installation process is different depending on whether you aremounting the camera outdoors or indoors. Follow the instructions

for the installation that you are performing.

Outdoor Installation

Important:The ideal outdoor location for mounting theairCam would be under an overhang/eave that sheltersthe camera. If the airCam is located in a completely openoutdoor environment without an overhang/eave, do not

install camera with a downtilt of more than 45.

45

Celing Mount

Wall-Mount

Camera is at 45degrees when the

indicator on the joint isaligned with the cornerof the mounting arm.


7/28

5


1. Press down on the release to remove the Ethernet Door.

Important:Do not remove the plug.

Plug

2. Connect the Ethernet cable to the Ethernet port.


8/28

6

airCam

3. Insert the Sealinto the bottom of the camera and wrap the Sealaround the Ethernet cable. Reconnect the Ethernet Doorto theairCam, leaving the Ethernet cable fed through the seal at thebottom of the camera.

4. Insert the Mounting Bracketinto the Mounting Slotsuntil a clickis heard to confirm a secure connection.


9/28

7


5. There are three recessed areas for the Ethernet cable on theMounting Bracket Base. Thread the Ethernet cable through twoof the recessed areas and out the one that will be closest to yourpower source.

Important:If the power source is above the camera, extendthe cable 70-80 mm below the camera body before routingup to the power source.

6. Position the Mounting Bracketin the desired location and use apencil to mark the holes on the wall.

7. Use a 6 mm drill bit to drill the holes in the wall.

8. Insert a Screw Anchorinto each hole.9. Secure the Mounting Bracketto the wall using the Self-Tapping

Screws.


10/28

8

airCam

Indoor Installation

1. Remove the screw and knob that connect the MountingBracketBaseto the camera attachment by turning the knob

counter-clockwise.Mounting Bracket Base

2. Insert an Ethernet cable through the Mounting BracketBase.

3. Reconnect the Mounting Bracket Baseto the cameraattachment by reconnecting the screw and knob. Turn theknob clockwise to lock the camera attachment back to theMounting BracketBase.


11/28

9

Indoor Installation

4. Unscrew the Plugon the back of the airCam.

5. Connect the Ethernet cable to the Ethernet port.

6. Insert the Mounting Bracketinto the Mounting Slotsuntil a clickis heard to confirm a secure connection.


12/28

10

airCam

7. Position the Mounting Bracketin the desired location and use apencil to mark the holes on the wall.

8. Use a 6 mm drill bit to drill the holes in the wall.

9. Insert the three Screw Anchorsinto the wall.10. Secure the Mounting Bracketto the wall using the Self-Tapping

Screws.

Note:There are three recessed areas for the Ethernet

cable on the Mounting Bracket Base. Place the Ethernetcable in the recessed area that will be closest to yourpower source.

Connecting the Power

1. Connect the other end of the Ethernet cable to the Ethernetport labeled POEon the PoE Adapter.


13/28

11

Connecting the Power

2. Connect an Ethernet cable from your LAN to the Ethernet portlabeled LANon the PoE Adapter.

3. Connect the power cord to the power port on the PoE Adapter.Connect the other end of the power cord to a power outlet.The Power LED should light up on the airCam.


14/28

12

airCam

airVision

Download and install the latest version of the airVision software atdownloads.ubnt.com/airvision; the airVision auto management

feature should automatically detect and install your new camera.

Go to the airVision interface to verify the camera is installed. Itshould appear on the left under Unplaced Cameras.

Drag the Camera to the appropriate location on the map.

Click the Camera icon. Click the Live Feed icon and a live feed of the camera should

be displayed.

Skip toAdjusting the Camera Viewon page 15.


15/28

13

Camera Configuration Interface

Camera Configuration Interface

Access the Camera Configuration Interface if you have not yetinstalled airVision, or plan to use the airCam as a stand-alone

camera without airVision.1. Make sure that your host machine is connected to the same

LAN as the airCam.

2. The airCam is set to DHCP by default. If you have a router orDHCP server providing addresses on your network, pleasecheck your DHCP Client Table or download the UbiquitiDiscovery Tool from: http://www.ubnt.com/download#app

Note:If you do not have a DHCP server, the airCamdefaults to the IP address 192.168.1.20.

4. Launch your web browser and in the address field, typehttp://and then the IP address of the airCam, for example:http://192.168.1.20. Press enter(PC) or return(Mac).

5. The login screen will appear. Enter ubntin the UsernameandPasswordfields and click Login.


16/28

14

airCam

6. The Mainscreen will appear and you should see a live videostream from the airCam.

Note:If you need to change the airCam network settings(DHCP/Static), go to Network Settingson the Devicetab.


17/28

15

Adjusting the Camera View

Adjusting the Camera View

Adjusts Camera Side to Side

Adjusts Camera Up and Down

Adjusts Mounting

Bracket Base

Adjusts Camera Focus

Hardware installation is complete. For details on using theairVision software or the Camera Configuration Interface,download the User Guide from downloads.ubnt.com/airvision


18/28

16

airCam

Limited WarrantyUBIQUITI NETWORKS, Inc (UBIQUITI NETWORKS) warrants that theproduct(s) furnished hereunder (the Product(s)) shall be free from defects

in material and workmanship for a period of one (1) year from the dateof shipment by UBIQUITI NETWORKS under normal use and operation.UBIQUITI NETWORKS sole and exclusive obligation and liability underthe foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,to repair or replace any Product that fails to conform to the abovewarranty during the above warranty period. The expense of removal andreinstallation of any Product is not included in this warranty. The warrantyperiod of any repaired or replaced Product shall not extend beyond itsoriginal term.

Warranty ConditionsThe above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,except by Ubiquiti Networks, or Ubiquiti Networks authorizedrepresentatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;(IV) has been subjected to misuse, abuse, negligence, abnormal physical,

electromagnetic or electrical stress, including lightning strikes, oraccident;

(V) has been damaged or impaired as a result of using third partyfirmware;

(VI) has no original Ubiquiti MAC label, or is missing any other originalUbiquiti label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of theRMA.

In addition, the above warranty shall apply only if: the product has beenproperly installed and used at all times in accordance, and in all materialrespects, with the applicable Product documentation; all Ethernet cablingruns use CAT5 (or above), and for outdoor installations, shielded Ethernetcabling is used, and for indoor installations, indoor cabling requirementsare followed.


19/28

17

Limited Warranty

Returns

No Products will be accepted for replacement or repair without obtaininga Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITINETWORKS facility freight prepaid in accordance with the RMA process ofUBIQUITI NETWORKS. Products returned without an RMA number will notbe processed and will be returned freight collect or subject to disposal.Information on the RMA process and obtaining an RMA number can befound at: www.ubnt.com/support/warranty .

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITINETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIMAND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESSFOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANYWARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR

TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NORITS THIRD PARTY PROVIDERS CONTROL BUYERS EQUIPMENT OR THETRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDINGTHE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BESUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONSAND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONSFACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRDPARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,

DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENTCORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANYOF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrantthat the operation of the Products will be error-free or that operation willbe uninterrupted. In no event shall UBIQUITI NETWORKS be responsiblefor damages or claims of any nature or description relating to systemperformance, including coverage, buyers selection of products (includingthe Products) for buyers application and/or failure of products (includingthe Products) to meet government or regulatory requirements.


20/28

18

airCam

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILLUBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR

DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISINGOUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THEPRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHERLEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OFSUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of impliedwarranties or conditions, so the above exclusion may not apply to you.You may have other rights that vary from country to country, state tostate, or province to province. Some countries, states and provinces do notallow the exclusion or limitation of liability for incidental or consequentialdamages, so the above limitation may not apply to you. EXCEPT TOTHE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DONOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THEMANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANYSOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations

Convention on Contracts for the International Sale of Goods shall not applyto any transactions regarding the sale of the Products.


21/28

19

Compliance

Compliance

FCC

Changes or modifications not expressly approved by the party responsiblefor compliance could void the users authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject tothe following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, includinginterference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection againstharmful interference when the equipment is operated in a commercialenvironment. This equipment generates, uses, and can radiate radiofrequency energy and, if not installed and used in accordance withthe instruction manual, may cause harmful interference to radiocommunications. Operations of this equipment in a residential area is likelyto cause harmful interference in which case the user will be required tocorrect the interference at his own expense.

Industry Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numrique de la classe A est conforme la norme NMB-003du Canada.

CE Marking

CE marking on this product represents the product is in compliance withall directives that are applicable to it.


22/28

20

airCam

RoHS/WEEE Compliance Statement

EnglishEuropean Directive 2002/96/EC requires that the equipment bearingthis symbol on the product and/or its packaging must not be disposedof with unsorted municipal waste. The symbol indicates that thisproduct should be disposed of separately from regular household wastestreams. It is your responsibility to dispose of this and other electric and

electronic equipment via designated collection facilities appointed by thegovernment or local authorities. Correct disposal and recycling will helpprevent potential negative consequences to the environment and humanhealth. For more detailed information about the disposal of your oldequipment, please contact your local authorities, waste disposal service, orthe shop where you purchased the product.

DeutschDie Europische Richtlinie 2002/96/EC verlangt, dass technische

Ausrstung, die direkt am Gert und/oder an der Verpackung mit diesemSymbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfallentsorgt werden darf. Das Symbol weist darauf hin, dass das Produktvon regulrem Haushaltmll getrennt entsorgt werden sollte. Esliegt in Ihrer Verantwortung, dieses Gert und andere elektrischeund elektronische Gerte ber die dafr zustndigen und von derRegierung oder rtlichen Behrden dazu bestimmten Sammelstellen zuentsorgen. Ordnungsgemes Entsorgen und Recyceln trgt dazu bei,potentielle negative Folgen fr Umwelt und die menschliche Gesundheit

zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung IhrerAltgerte bentigen, wenden Sie sich bitte an die rtlichen Behrden oderstdtischen Entsorgungsdienste oder an den Hndler, bei dem Sie dasProdukt erworben haben.

EspaolLa Directiva 2002/96/CE de la UE exige que los equipos que lleven estesmbolo en el propio aparato y/o en su embalaje no deben eliminarsejunto con otros residuos urbanos no seleccionados. El smbolo indica

que el producto en cuestin debe separarse de los residuos domsticosconvencionales con vistas a su eliminacin. Es responsabilidad suyadesechar este y cualesquiera otros aparatos elctricos y electrnicos atravs de los puntos de recogida que ponen a su disposicin el gobierno ylas autoridades locales. Al desechar y reciclar correctamente estos aparatosestar contribuyendo a evitar posibles consecuencias negativas para elmedio ambiente y la salud de las personas. Si desea obtener informacinms detallada sobre la eliminacin segura de su aparato usado, consulte alas autoridades locales, al servicio de recogida y eliminacin de residuos de

su zona o pregunte en la tienda donde adquiri el producto.


23/28

21

Compliance

FranaisLa directive europenne 2002/96/CE exige que lquipement sur lequelest appos ce symbole sur le produit et/ou son emballage ne soit pas jetavec les autres ordures mnagres. Ce symbole indique que le produit

doit tre limin dans un circuit distinct de celui pour les dchets desmnages. Il est de votre responsabilit de jeter ce matriel ainsi que toutautre matriel lectrique ou lectronique par les moyens de collecteindiqus par le gouvernement et les pouvoirs publics des collectivitsterritoriales. Llimination et le recyclage en bonne et due forme ont pourbut de lutter contre limpact nfaste potentiel de ce type de produitssur lenvironnement et la sant publique. Pour plus dinformations sur lemode dlimination de votre ancien quipement, veuillez prendre contactavec les pouvoirs publics locaux, le service de traitement des dchets, ou

lendroit o vous avez achet le produit.

ItalianoLa direttiva europea 2002/96/EC richiede che le apparecchiaturecontrassegnate con questo simbolo sul prodotto e/o sullimballaggio nonsiano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indicache questo prodotto non deve essere smaltito insieme ai normali rifiutidomestici. responsabilit del proprietario smaltire sia questi prodotti siale altre apparecchiature elettriche ed elettroniche mediante le specifiche

strutture di raccolta indicate dal governo o dagli enti pubblici locali. Ilcorretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenzepotenzialmente negative per lambiente e per la salute dellessere umano.Per ricevere informazioni pi dettagliate circa lo smaltimento delle vecchieapparecchiature in Vostro possesso, Vi invitiamo a contattare gli entipubblici di competenza, il servizio di smaltimento rifiuti o il negozio nelquale avete acquistato il prodotto.


24/28

22

airCam

Declaration of Conformity

esky[Czech]

UBIQUITI NETWORKS tmto prohla uje, e tento UBIQUITINETWORKS device, je ve shod se zkladnmi po adavky a dal mi p

slu n mi ustanovenmi sm rnice 1999/5/ES.

Dansk[Danish]

Undertegnede UBIQUITI NETWORKS erklrer herved, at flgendeudstyr UBIQUITI NETWORKS device, overholder de vsentlige kravog vrige relevante krav i direktiv 1999/5/EF.

Nederlands[Dutch]

Hierbij verklaart UBIQUITI NETWORKS dat het toestel UBIQUITINETWORKS device, in overeenstemming is met de essentile eisenen de andere relevante bepalingen van richtlijn 1999/5/EG.

Bij deze verklaart UBIQUITI NETWORKS dat deze UBIQUITI

NETWORKS device, voldoet aan de essentile eisen en aan deoverige relevante bepalingen van Richtlijn 1999/5/EC.

English Hereby, UBIQUITI NETWORKS, declares that this UBIQUITINETWORKS device, is in compliance with the essential requirementsand other relevant provisions of Directive 1999/5/EC.

Eesti[Estonian]

Kesolevaga kinnitab UBIQUITI NETWORKS seadme UBIQUITINETWORKS device, vastavust direktiivi 1999/5/E phinuetele janimetatud direktiivist tulenevatele teistele asjakohastele stetele.

Suomi[Finnish] UBIQUITI NETWORKS vakuuttaa tten ett UBIQUITI NETWORKSdevice, tyyppinen laite on direktiivin 1999/5/EY oleellistenvaatimusten ja sit koskevien direktiivin muiden ehtojenmukainen.

Franais[French]

Par la prsente UBIQUITI NETWORKS dclare que lappareilUBIQUITI NETWORKS, device est conforme aux exigencesessentielles et aux autres dispositions pertinentes de la directive1999/5/CE.

Deutsch

[German]

Hiermit erklrt UBIQUITI NETWORKS, dass sich diese UBIQUITI

NETWORKS device, in bereinstimmung mit den grundlegendenAnforderungen und den anderen relevanten Vorschriften derRichtlinie 1999/5/EG befindet. (BMWi)

[Greek]

UBIQUITI NETWORKS UBIQUITINETWORKS device, 1995/5/.

Magyar

[Hungarian]

Alulrott, UBIQUITI NETWORKS nyilatkozom, hogy aUBIQUITI NETWORKS device, megfelel a vonatkoz alapvet

kvetelmnyeknek s az 1999/5/EC irnyelv egyb elrsainak.

slenska[Icelandic]

Hr me l sir UBIQUITI NETWORKS yfir v a UBIQUITI NETWORKSdevice, er samrmi vi grunnkrfur og a rar krfur, sem ger ar eru tilskipun 1999/5/EC.

Italiano[Italian]

Con la presente UBIQUITI NETWORKS dichiara che questo UBIQUITINETWORKS device, conforme ai requisiti essenziali ed alle altredisposizioni pertinenti stabilite dalla direttiva 1999/5/CE.


25/28

23

Declaration of Conformity

Latviski[Latvian]

Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device,atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saisttajiem noteikumiem.

Lietuvikai

[Lithuanian]

UBIQUITI NETWORKS deklaruoja, kad is UBIQUITI NETWORKS

renginys atitinka esminius reikalavimus ir kitas 1999/5/EBDirektyvos nuostatas.

Malti[Maltese]

Hawnhekk, UBIQUITI NETWORKS, jiddikjara li dan UBIQUITINETWORKS device, jikkonforma malti ijiet essenzjali u maprovvedimenti o rajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

Norsk[Norwegian]

UBIQUITI NETWORKS erklrer herved at utstyret UBIQUITINETWORKS device, er i samsvar med de grunnleggende krav ogvrige relevante krav i direktiv 1999/5/EF.

Slovensky[Slovak]UBIQUITI NETWORKS t mto vyhlasuje, e UBIQUITI NETWORKSdevice, sp a zkladn po iadavky a v etky prslu n ustanoveniaSmernice 1999/5/ES.

Svenska[Swedish]

Hrmed intygar UBIQUITI NETWORKS att denna UBIQUITINETWORKS device, str I verensstmmelse med de vsentligaegenskapskrav och vriga relevanta bestmmelser som framgr avdirektiv 1999/5/EG.

Espaol[Spanish]

Por medio de la presente UBIQUITI NETWORKS declara que elUBIQUITI NETWORKS device, cumple con los requisitos esenciales

y cualesquiera otras disposiciones aplicables o exigibles de laDirectiva 1999/5/CE.

Polski[Polish]

Niniejszym, firma UBIQUITI NETWORKS o wiadcza, e produkt seriiUBIQUITI NETWORKS device, spenia zasadnicze wymagania i inneistotne postanowienia Dyrektywy 1999/5/EC.

Portugus[Portuguese]

UBIQUITI NETWORKS declara que este UBIQUITI NETWORKS device,est conforme com os requisitos essenciais e outras disposies daDirectiva 1999/5/CE.

Romn[Romanian] Prin prezenta, UBIQUITI NETWORKS declar c acest dispozitivUBIQUITI NETWORKS este n conformitate cu cerinele eseniale ialte prevederi relevante ale Directivei 1999/5/CE.


26/28

24

airCam

R061713720-00053-01

The Advanced Gigabit PoE Managed Switchfrom Ubiquiti NetworksPower your Ubiquiti devices withTOUGHSwitchPoE. TOUGHSwitch PoEdelivers reliable power and fast Gigabitconnectivity to devices that supportpassive Power over Ethernet.

Simplify Your DeploymentTOUGHSwitch PoE deployments increase efficiency and greatly reducethe number of potential failure points, resulting in faster installations andless maintenance and troubleshooting. TOUGHSwitch PoE allows networkarchitects to design cleaner, less cluttered deployments.

Before TOUGHSwitch PoE After TOUGHSwitch PoE

Available Models

TS-5-POE

5 Gigabit Ports, 24V PoETS-5-PRO

8 Gigabit Ports, 24V or 48V PoE

TS-16-CARRIER

16 Gigabit Ports, 24V or 48V PoE, Rack-Mountable


27/28


28/28

w w w . u b n t . c o m

Support support.ubnt.com

Community community.ubnt.com

Downloads downloads.ubnt.com

Documents

Hardware - Camara Ubiquiti AirCam_QSG