HDMI Fiber Optic Cable Extender OPF-TH1000D/OPF-RH1000Didkav.com/wp-content/uploads/2020/07/OPF-H1000D...HDMI cable fixing hole Hole for the attached cable clamp to secure an HDMI

HDMI Fiber Optic Cable Extender

OPF-TH1000D/OPF-RH1000D

<User Guide>

<Command Reference Guide>

Ver.1.10.0

RS

-23

2C

FG

DC

5V

3A

LA

UD

IO O

UT

PU

TR

POWERSTATUS

HDCP

HD

MI

INP

UT

Tx

OPTICAL DAISYCHAIN Tx for HDMI OPF-TH1000D RX

OP

TIC

AL

TX

CLASS 1 LASER PRODUCT

クラス 1 レーザ製品

KEY LOCK

－＋SET

SIG

NA

L

RS

-23

2C

FG

DC

5V

3A

POWERSTATUS

HDCP

HD

MI

OU

TP

UT

Rx

OPTICAL DAISYCHAIN Rx for HDMI OPF-RH1000D RX

OP

TIC

AL

TX

SIG

NA

L

DIP

SW



⚫ Thank you for choosing our product.

⚫ To ensure the best performance of this product, please read this user guide fully and carefully before

using it and keep this manual together with the product for future reference as needed.

IDK Corporation

OPF-TH1000D/OPF-RH1000D User Guide/Command Guide

2

Trademarks

⚫ Blu-ray Disc and Blu-ray are trademarks of Blu-ray Disc Association.

⚫ The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or

registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.

⚫ All other company and product names mentioned in this manual are either registered trademarks or

trademarks of their respective owners. In this manual, the “®” or “™” marks may not be specified.


3

Before reading this manual

⚫ All rights reserved.

⚫ Some information contained in this User guide such as exact product appearance, diagrams, menu

operations, and so on may differ depending on the product version.

⚫ This User guide is subject to change without notice. You can download the latest version from IDK’s

website at: http://www.idkav.com

FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

CE MARKING

This equipment complies with the essential requirements of the relevant European health, safety and

environmental protection legislation.

WEEE MARKING Waste Electrical and Electronic Equipment (WEEE), Directive 2002/96/EC (This directive is only valid in the EU.) This equipment complies with the WEEE Directive (2002/96/EC) marking requirement. The left marking indicates that you must not discard this electrical/electronic equipment in

domestic household waste.

The lasers in this product meet Class 1 Laser Safety per FDA/CDRH and

EN (IEC) 60825 laser safety standards which specifies design safety.



http://www.idkav.com/


4

Safety Instructions Read and understand all safety and operating instructions before using this product. Follow all instructions

and heed all warnings/cautions.

Enforcement Symbol Description

Indicates the presence of a hazard that may result in death or serious

personal injury if the warning is ignored or the product is handled

incorrectly.

Indicates the presence of a hazard that may cause minor personal

injury or property damage if the caution is ignored or the product is

handled incorrectly.

Symbol Description Example

Caution

This symbol is intended to alert the user. (Warning and caution)

Electrical

Hazard

Prohibited

This symbol is intended to prohibit the user from specified actions.

Do not

disassemble

Instruction

This symbol is intended to instruct the user.

Unplug

Warning

Caution


5

■ For lifting heavy products:

Instruction

● Lifting must be done by two or more personnel.

To avoid injury: When lifting the product, bend your knees, keep your back straight and get close to it with two or

more persons.

■ For installing and connecting products:

Prohibited

● Do not place the product upon a surface that may give way or that may become

unstable.

Install the product in a secure and stable place to prevent it from falling and possibly causing injury.

● Secure the product if installing in locations prone to vibration or movement.

Otherwise, it may move unexpectedly or it may fall and lead to injury.

Instruction

● Installation work must be performed by professionals.

The product is intended to be installed by skilled technicians. For installation, please contact a system integrator

or IDK. Improper installation may lead to the risk of fire, electric shock, injury, or property damage.

● Insert the power plug into an outlet that is unobstructed. Unobstructed access to the plug enables unplugging the product in case of any extraordinary failure, abnormal

situation or for easy disconnection during extended periods of non-use.

● Insert the power plug into an appropriate outlet completely.

If the plug is partially inserted, arching may cause the connection to overheat, increasing the risk of electrical

shock or fire. Do not use a damaged plug or connect to a damaged outlet.

● Unplug the product from the AC power source during installation or service.

When connecting peripheral devices to this product, unplug all involved devices from outlets. Ground potential

differences may cause fire or other difficulties.

■ For operating products:

Prohibited

● Keep out any foreign objects.

To avoid fire or electric shock, do not permit foreign objects, such as metal and paper, to enter the product from

vent holes or other apertures.

● For power cable/ plug:

・Do not scratch, heat, or modify, including splicing or lengthening them.

・Do not pull, place heavy objects on them, or pinch them.

・Do not bend, twist, tie or clamp them together forcefully.

Misuse of the power cable and plug may cause fire or electric shock. If power cables/plugs become damaged,

contact your IDK representative.

Do not

disassemble

● Do not repair, modify or disassemble.

Since the product includes circuitry that uses potentially lethal, high voltage levels, disassembly by unauthorized

personnel may lead to the risk of fire or electric shock. For internal inspection or repair, contact your IDK

representative.

Do not touch

● Do not touch the product and connected cables during electrical storms.

Contact may cause electric shock

Instruction

● Clean the power plug regularly.

If the plug is covered in dust, it may increase the risk of firer.

Warning


6

■ If the following problem occurs:

Unplug

● Unplug immediately if the product smokes, makes unusual noise, or produces a

burning odor.

If you continue to use the product under these conditions, it may cause electric shock or fire.

● Unplug immediately if the product is damaged by falling or having been dropped.

If you continue to use the product under these conditions, it may increase the risk of electrical shock or fire. For

maintenance and repair, contact your IDK representative.

● Unplug immediately if water or other objects are directed inside.

If you continue to use the product under these conditions, it may increase the risk of electrical shock or fire. For

maintenance and repair, contact your IDK representative.

Warning


7

■ For installing and connecting products:

Prohibited

● Do not place the product in a location where it will be subjected to high

temperatures.

If the product is subjected to direct sunlight or high temperatures while under operation, it may affect the

product’s performance and reliability and may increase the risk of fire.

● Do not store or operate the product in dusty, oil smoke filled, or humid place.

If the product is placed near humidifiers or in a dusty area, it may increase the risk of fire or electric shock.

● Do not block the vent holes. If ventilation slots are blocked, it may cause the product to overheat, affecting performance and reliability and

may increase the risk of fire.

● Do not place or stack heavy items on the product.

Failure to observe this precaution may result in damage to the product and other property and may lead to the

risk of personal injury.

● Do not exceed ratings of outlet and wiring devices.

Exceeding the rating of an outlet may increase the risk of fire and electric shock.

No wet hands

● Do not handle power plug with wet hands. Failure to observe this precaution may increase the risk of electrical shock.

Instruction

● Use and store the product within the specified temperature/humidity range.

If the product is used outside the specified range for temperature and humidity continuously, it may increase the

risk of fire or electric shock.

● Do not place the product at elevations of 1.24 mi. (2,000 m) or higher above sea

level.

Failure to do so may shorten the life of the internal parts and result in malfunctions.

● When mounting the product into the rack, provide sufficient cooling space.

Mount the product in a rack meeting EIA standards, and maintain spaces above and below for air circulation. For

your safety as required, attach an L-shaped bracket in addition to the panel mount bracket kit to improve

mechanical stability.

● Never insert screws without the rubber feet into the threaded holes on the bottom

of the product.

Never insert screws without the rubber feet into the threaded holes on the bottom of the product. Doing so may

lead to damage when the screws contact electrical circuitry or components inside the product.

Reinstall the originally supplied rubber feet using only the originally supplied screws.

■ For operating products:

Prohibited

● Use only the supplied power cable and AC adapter. ● Do not use the supplied power cable and AC adapter with other products.

If non-compliant adapter or power cables are used, it may increase the risk of fire or electrical shock.

Unplug

● If the product won’t be used for an extended period of time, unplug it.

Failure to observe this precaution may increase the risk of fire.

● Unplug the product before cleaning.

To prevent electric shock.

Instruction

● If cooling fan stops, power off the product and contact us.

Failure to do so may rise internal temperature and increase the risk of malfunction, fire, or electric shock.

● Clean the vent holes regularly.

If the vent holes of the cooling fan is covered in dust, internal temperature rises and it may increase the risk of

malfunction, fire, or electric shock.

Caution


8

Table of Contants

1 Included items .......................................................................................................................................... 10

2 Precautions for shipping .......................................................................................................................... 11

3 Product outline ......................................................................................................................................... 12

4 Features ................................................................................................................................................... 13

5 Part names and descriptions ................................................................................................................... 14

5.1 Transmitter .......................................................................................................................................... 14

5.2 Receiver .............................................................................................................................................. 16

6 Precautions .............................................................................................................................................. 18

6.1 Installation ........................................................................................................................................... 18

6.2 Cabling ................................................................................................................................................ 19

6.2.1 Cables ......................................................................................................................................... 19

6.2.2 Fiber optic cable .......................................................................................................................... 19

6.2.3 SFP optical transceiver ............................................................................................................... 20

6.2.4 RS-232C cable ............................................................................................................................ 20

6.2.5 AC adapter with screw locking mechanism ................................................................................ 21

6.3 Application example ............................................................................................................................ 22

7 Basic operation ........................................................................................................................................ 23

7.1 Menu operation buttons ...................................................................................................................... 23

7.2 Locking menu operation buttons ......................................................................................................... 24

7.3 Initialization ......................................................................................................................................... 24

7.4 Setting transmitter and receiver using setting mode .......................................................................... 25

7.4.1 Setting transmitter ....................................................................................................................... 26

7.4.2 Setting receiver ........................................................................................................................... 27

8 Menus ...................................................................................................................................................... 28

8.1 Menu list .............................................................................................................................................. 28

8.2 Setting input and output (Setup menu) ............................................................................................... 30

8.2.1 [F10] EDID resolution .................................................................................................................. 30

8.2.2 [F16] No-signal input monitoring time ......................................................................................... 32

8.2.3 [F22] PCM Audio ......................................................................................................................... 33

8.2.4 [F24] AC-3 Dolby Digital Audio ................................................................................................... 33

8.2.5 [F26] AAC Audio ......................................................................................................................... 33

8.2.6 [F28] Dolby Digital Plus Audio..................................................................................................... 34

8.2.7 [F30] DTS Audio .......................................................................................................................... 34

8.2.8 [F32] DTS-HD Audio ................................................................................................................... 34

8.2.9 [F34] Dolby TrueHD Audio .......................................................................................................... 35

8.2.10 [F36] Audio channel .................................................................................................................... 35

8.2.11 [F65] Audio output ....................................................................................................................... 36

8.2.12 [F76] EDID WXGA ...................................................................................................................... 36

8.2.13 [F90] Version ............................................................................................................................... 36

8.2.14 [F99] Maintenance/status display menu ..................................................................................... 36

8.3 Verifying operation (Maintenance menu) ............................................................................................ 37

8.3.1 [C06] HDCP input setting ............................................................................................................ 37

8.3.2 [C55] Forced color conversion output ......................................................................................... 38

8.3.3 [C90] RS-232C communication mode ........................................................................................ 38

8.4 Displaying I/O status (status display menu) ....................................................................................... 39

8.4.1 [L01 to L13] Displaying information about input .......................................................................... 39

8.4.2 [L50] Displaying information about output ................................................................................... 42


9

9 Command ................................................................................................................................................. 43

9.1 Command outline ................................................................................................................................ 43

9.2 Command list ...................................................................................................................................... 43

9.3 Command description ......................................................................................................................... 44

9.3.1 Error status .................................................................................................................................. 44

9.3.2 Setting command ........................................................................................................................ 45

9.3.3 Status acquisition command ....................................................................................................... 46

10 Specification ............................................................................................................................................. 48

10.1 Pin assignments .................................................................................................................................. 48

10.1.1 HDMI Type A connector .............................................................................................................. 48

10.1.2 RS-232C connector ..................................................................................................................... 48

10.2 Product specification ........................................................................................................................... 50

10.2.1 OPF-H1000D .............................................................................................................................. 50

10.2.2 SFP Specification ........................................................................................................................ 50

11 Troubleshooting ....................................................................................................................................... 51


10

1 Included items

Make sure all items below are included in the package.

If any items are missing or damaged, please contact IDK.

“OPF-H1000D” mentioned in this manual refers to OPF-TH1000D and OPF-RH1000D set.

■ Transmitter (OPF-TH1000D)

・ OPF-TH1000D (main unit) x 1

・ SFP optical transceiver x 1

・ AC adapter with screw locking mechanism (5.9 ft. (1.8 m)) x 1

・ Cable clamp x 1

■ Receiver (OPF-RH1000D)

・ OPF-RH1000D (main unit) x 1

・ SFP optical transceiver x 1

・ AC adapter with screw locking mechanism (5.9 ft. (1.8 m)) x 1

・ Cable clamp x 1

RS-2

32C

FG

DC

5V

3A

L AU

DIO

OU

TPU

TR

POWERSTATUS

HDCP

HD

MI

INP

UT

Tx


OP

TIC

AL

TX



KEY LOCK

－＋SET

SIG

NA

L

OPF-TH1000D

RS-2

32C

FG

DC

5V

3A

POWERSTATUS

HDCP

HD

MI

OU

TPU

T

Rx


OP

TIC

AL

TX

SIG

NA

L

DIP

SW



OPF-RH1000D

SFP optical transceiver

AC adapter with screw

locking mechanism

(5.9 ft. (1.8 m))

Cable clamp

Included items

Tip:

Dust caps are attached to SFP optical transceiver and the connector.

These caps will be used for shipping or repairing the OPF-H1000D unit.


11

2 Precautions for shipping

The OPF-TH1000D/OPF-RH1000D has an SFP optical transceiver that is vulnerable to damage caused by

mishandling during shipment if it is improperly packaged.

If, for any reason, you need to ship the device, remove the transceiver from the device and plug the dust cap

into the transceiver and the connector. Put the removed transceiver in an electrostatic bag with enough

cushion and keep the bag and device together in a box.

To install a transceiver:

Make sure the bale clasp is closed.

Line up the transceiver with the port and slide it into

the port until you hear a click.

Removing a transceiver:

Open the bale clasp and pull the transceiver out

of the port.

Removing and installing SFP optical transceiver

Note:

When installing the SFP transceiver, push it firmly and ensure that it is completely seated and the bale clasp

is locked. Do not open the bale clasp except for removing the transceiver.

RemovingInstalling

SFP transceiver

Bale clasp


12

3 Product outline

The OPF-H1000D is a transmitter and receiver set that enables HDMI signals to be transmitted long distance

over fiber optical cables. It also supports Daisy Chain.

■ For multimode fiber

・ Transmitter : OPF-TH1000D-MM

・ Receiver : OPF-RH1000D-MM

■ For singlemode fiber

・ Transmitter : OPF-TH1000D-SM

・ Receiver : OPF-RH1000D-SM

RS

-232

C

FG

DC

5V

3A

L

AU

DIO

OU

TP

UT

R

POWERSTATUS

HDCP

HD

MI

INP

UT

Tx


OP

TIC

AL

TX



KEY LOCK

－＋SET

SIG

NA

L

RS

-232

C

FG

DC

5V

3A

POWERSTATUS

HDCP

HD

MI

OU

TP

UT

Rx


OP

TIC

AL

TX

SIG

NA

L

DIP

SW



The SPF optical transceiver can be

replaced depending on the fiber optic cable.

　　 OPF-TH1000D-MM

　　　　　　Multimode fiber

　　 OPF-TH1000D-SM

　　　　　　Singlemode fiber

　　 OPF-RH1000D-MM

　　　　　　Multimode fiber

　　 OPF-RH1000D-SM

　　　　　　Singlemode fiber

[Transmitter]

[Receiver]

OPF-H1000D series


13

4 Features

Input signals are transmitted without quality deterioration since they are not compressed or processed.

The OPF-H1000D also supports RS-232C serial one-way communication, and the transmitter outputs HDMI

embedded audio as analog audio.

■ Video

・ Up to 1080p/WUXGA (Reduced Blanking)

・ HDCP 1.4

・ Daisy chain connection

・ Transmission distances

Multimode fiber (OM3) : 984 ft. (300 m)

Multimode fiber (OM4) : 0.62 mi. (1 km)

Singlemode fiber (OS1) : 2.92 mi. (4.7 km), (Up to 6.21 mi. (10 km, optional))

■ Audio

・ De-embedding (OPF-TH1000D)

■ Communication

・ RS-232C

■ Others

・ AC adapter with locking mechanism

Projector

LCD monitor

Speaker

Blu-ray player

Amplifier

RS

-232C

FG

DC

5V

3A

L

AU

DIO

OU

TP

UT

R

POWERSTATUS

HDCP

HD

MI

INP

UT

Tx


OP

TIC

AL

TX



KEY LOCK

－＋SET

SIG

NA

L

RS

-232

C

FG

DC

5V

3A

POWERSTATUS

HDCP

HD

MI

OU

TP

UT

Rx


OP

TIC

AL

TX

SIG

NA

L

DIP

SW



RS

-232

C

FG

DC

5V

3A

POWERSTATUS

HDCP

HD

MI

OU

TP

UT

Rx


OP

TIC

AL

TX

SIG

NA

L

DIP

SW



Up to 16 ft. (5 m)

Laptop

Typical application (Daisy connection)


14

5 Part names and descriptions

5.1 Transmitter

RS

-23

2C

FG

DC

5V

3A

LA

UD

IO O

UT

PU

TR

POWERSTATUS

HDCP

HD

MI IN

PU

T

Tx


OP

TIC

AL

TX



KEY LOCK

－＋SET

SIG

NA

L

①

②

⑩⑪

③

⑤

⑧

⑫

④⑦

⑥

⑨

⑬

Panel drawing (Transmitter)

# Part name Description

① RS-232C port Port for RS-232C signals (only input)

② Audio output connector Outputs HDMI input audio as analog audio. For amplifiers, speakers, and

mixers.

③ Output connector for

extension

Output connector of digital optical signals for extension. Connected to the

receiver using a fiber optic cable.

④ LED for checking

transmitted or received

Lights in green when valid code is transmitted (TX) or received (RX).

⑤ HDMI input connector Input connector for HDMI signals

Connect a source device such as Blu-ray players.

⑥ HDMI cable fixing hole Hole for the attached cable clamp to secure an HDMI cable.

⑦ SIGNAL LED Lights in green when vertical synchronous signals are input from the

HDMI input connector.

⑧ AC adapter connector Connector for the attached AC adapter.

⑨ FG Frame ground


15


⑩ Menu operation

buttons

Sets I/O settings of the transmitter and locks menu operation buttons

・ Use “SET”, “+”, and “-” buttons to set I/O settings of the transmitter.

・ Press and hold the “SET” button in order to lock those buttons.

⑪ Segment display Displays menu items and setting status.

⑫ LED lights (green) ・ POWER

When power is supplied from the AC adapter, it lights.

・ HDCP

HDCP status of input video signals from the source device.

Lights : Video signals are input (with HDCP)

Blinks : Video signals are input (without HDCP)

Turned off : No video signals

・ KEY LOCK

The menu operation buttons are locked or released.

Lights : Locked

Blinks : Being set

Turned off : Unlocked

⑬ Connector for

maintenance

Please do not use this connector.


16

5.2 Receiver

RS

-23

2C

FG

DC

5V

3A

POWERSTATUS

HDCP

HD

MI O

UT

PU

T

Rx


OP

TIC

AL

TX

SIG

NA

L

DIP

SW



①

②

④⑦

③

⑤

⑧

⑥

⑨⑩⑪

Panel drawing (Receiver)


① RS-232C port Port for RS-232C signals (only output)

② DIP Switches Sets the receiver.

1. Setting RS-232C communication mode

OFF : Communication mode [Default]

ON : Setting mode (9600 bps)

2. Setting audio output

OFF : Output [Default]

ON : Not output

③ I/O connector for

extension

I/O connector of digital optical signals for extension. Connected to the

transmitter using a fiber optic cable.

Connected to another receiver for Daisy Chain connection.

④ LED for checking

transmitted or received

Lights in green when valid code is transmitted (TX) or received (RX).

⑤ HDMI output connector Output connector for HDMI signals. Connected to a sink device, such as

LCD monitors.

⑥ HDMI cable fixing hole Hole for the attached cable clamp to secure an HDMI cable.


17


⑦ SIGNAL LED Lights in green when vertical synchronous signals are input from the I/O

connector for extension.

⑧ AC adapter connector Connector for the attached AC adapter.

⑨ FG Frame ground

⑩ LED lights (green) ・ POWER

When power is supplied from the AC adapter, it lights.

・ HDCP

HDCP status of input video signals from the transmitter.

Lights : Video signals are input (with HDCP)

Blinks : Video signals are input (without HDCP)

Turned off : No video signals

⑪ Connector for

maintenance

Please do not use this connector.


18

6 Precautions

Before connecting to external devices, follow the precautions below.

6.1 Installation

When installing the OPF-H1000D, please observe the following precautions.

・ Do not stack or place the OPF-H1000D directly on top of another OPF-H1000D

・ Do not block vent holes. To provide adequate ventilation, maintain sufficient clearances around the

OPF-H1000D (1.2 in. (30 mm) or more)

・ When the OPF-H1000D needs to be mounted in an enclosed space or an EIA rack without using IDK’s

rack mounting hardware (RM-SF, RM-SH), ensure that a sufficient ventilation/cooling system is provided

to keep the ambient temperature at 104°F (40°C) or lower. If inadequately vented, the product’s service life,

operation, and reliability may be affected.

Maintain adequate clearances (1.2 in. (30 mm) or more) as shown below

Bad example

Good example

Good example

Necessary clearances


19

6.2 Cabling

When connecting the OPF-H1000D to external devices, please observe the following precautions.

・ Read manuals for the external devices.

・ Before connecting cables to the OPF-H1000D or an external device, dissipate static electricity by touching

grounded metal such as equipment racks before handling signal cables. Failure to observe this precaution

may result in ESD (electrostatic discharge) damage.

・ Turn off the OPF-H1000D before attaching or removing the SFP optical transceiver or cable connection.

・ Be sure to fully seat all plugs and connections and dress cables to reduce stress on connectors.

・ Before inserting or removing a fiber optic cable, make sure to first turn the OPF-H1000 off and not to touch

the ends of the fiber. Clean up the fiber before inserting it again.

・ Plug the dust cap into an LC connector of fiber optic cable that is not used.

・ Secure HDMI cables using cable clamps to prevent connectors from being accidently pulled out of ports.

Removing HDMI cable and cable clamp

Pull out while pressing

Click

Securing HDMI cable using cable clamp

Securing and removing cable clamp

6.2.1 Cables

Use the correct HDMI cable or HDMI-DVI conversion cable depending on the system configuration.

6.2.2 Fiber optic cable

・ Use a simplex fiber cable having LC connectors for both ends.

・ Use a cable whose length complies with the extension standard.


20

6.2.3 SFP optical transceiver

・ Plug the attached dust cap into the SFP optical transceiver when not connecting a fiber optic cable.

・ Do not use the attached SFP optical transceiver to other products, and do not use an SFP optical

transceiver of other product to the OPF-H1000D.

・ Do not use the SFP optical transceiver of the OPF-H1000D for other devices or connect fiber optical cable

that are connected to other devices to the SFP optical transceiver of the OPF-H1000D. It may cause

malfunctions of the SFP optical transceiver. The maximum receiving optic power used for the

OPF-H1000D is 0 dBm.

・ Pull the lever of the SFP optical transceiver in order to remove it. Lock the lever and push it into until it

clicks to attach the module.

LeverRX

OPT

ICA

LTX

SFP optical transceiver

6.2.4 RS-232C cable

・ RS-232C signals (up to 115.2 Kbps) can be transmitted in duplex over a long distance.

・ Use a cross cable or straight cable according to the connected devices.

【See: 10.1.2 RS-232C connector】


21

6.2.5 AC adapter with screw locking mechanism

The shapes of AC plugs with screw locking mechanism vary from country to country. The AC plug can be

removed from the AC adapter.

Removing AC plug:

Slide the AC plug (②) from the AC adapter while holding down the portion mentioned below (①)

①

②

Removing AC plug (Example: Plug type A)

Attaching AC plug:

Gently slide the AC plug into the AC adapter (③) until it clicks (④)

③

④

This tab should be fixed into

the part of the AC adapter.

Tab

Attaching AC plug (Example: Plug type A)


22

6.3 Application example

Digital video and audio are transmitted from the Blu-ray disc player to the transmitter. The transmitter sends

those signals to the receiver over a fiber optic cable, and it also converts digital audio signals to analog and

outputs them to the amplifier. The receiver outputs the received video and audio signals to the projector from

the HDMI output connector.

You can control peripheral devices (such as projectors) by using a control device (such as PCs).

Note:

The OPF-TH1000D must be paired with OPF-RH1000D. The OPF-H1000D cannot be connected to an I/O

board of the FDX series or other models of the OPF series.

Projector

Speakers

Blu-ray disc player

Amplifier

RS

-23

2C

FG

DC

5V

3A

LA

UD

IO O

UT

PU

TR

POWERSTATUS

HDCP

HD

MI IN

PU

TTx


OP

TIC

AL

TX



KEY LOCK

－＋SET

SIG

NA

L

RS

-23

2C

FG

DC

5V

3A

POWERSTATUS

HDCP

HD

MI O

UT

PU

T

Rx


OP

TIC

AL

TX

SIG

NA

L

DIP

SW



Laptop

Source and sink devices are connected

Notes:

・ Make sure to plug the dust caps into the following two connectors to which a fiber optic cable is not

connected: a transmitter connector for extension (right end) and an I/O connector for extension of the last

receiver (left end).

・ Cut the attached dust cap in half before pulling them to connectors.


23

7 Basic operation

7.1 Menu operation buttons

Setting input and output of the transmitter using the menu operation buttons.

To use menu operation buttons:

Select the menu number first and then select the setting number.

Use a thin stick to press buttons.

Notes:

・ If no operation is performed for 10 seconds in step 5, the procedure will be returned to step 2.

・ If no operation is performed for 60 seconds in each step, the segment display is turned off.

■ Procedure

1 Press the “SET” button. The

segment display lights.

2 Select the menu number using “＋”

and “－” buttons.

3 Press the “SET” button to apply the

menu number.

4 Select the setting number using ”＋”

and “－” buttons.

5 Press the “SET” button to apply the

setting.

The display of step 2 is displayed

again.

If no operation is performed for 10

seconds in step 5, the procedure

will be returned to step 2.

Using menu operation keys

POWERSTATUS

HDCPTx KEY LOCK

－＋SET

1, 3

2

Selecting menu

number

SettingPOWER

STATUSHDCPTx KEY LOCK

－＋SET

5

4


24

7.2 Locking menu operation buttons

Press and hold the “SET” button for a few seconds in order to lock the menu operation buttons. You can

release the lock by pressing the button again.

Locking menu operation buttons (transmitter only)

7.3 Initialization

Settings of the transmitter can be reset to factory default values by turning on the OPF-H1000D while

pressing the “SET” button. The receiver does not have this setting.

Note:

Once you have initialized the settings, they cannot be reversed.

POWERSTATUS

HDCPTx KEY LOCK

－＋SET

Press this key and turn on the transmitter.

POWERSTATUS

HDCP KEY LOCK

－＋SET

POWERSTATUS

HDCP KEY LOCK

－＋SET

Initialized

Initialization (transmitter only)

POWERSTATUS

HDCPTx KEY LOCK

－＋SET

Press and hold this key

Blinks (being set)Turned off (lock

is released)Lights (locked)

KEY LOCK KEY LOCK KEY LOCK


25

7.4 Setting transmitter and receiver using setting mode

The OPF can be set and I/O statuses can be acquired with serial communication commands by setting

RS-232C communication mode to the setting mode. You can set RS-232C to the setting mode by setting

[C90] to “01” for the transmitter and by turning on DIP SW1 for the receiver.

Connect a control device, such as PC, and the OPF-H1000D via an RS-232C cable in order to control the

OPF using terminal software.

Since the communication settings are fixed with setting mode as follows, set the terminal software according

to the settings of the OPF-1000HD.

Item Setting

Communication standard RS-232C

Baud rate 9600 [bps]

Data bit length 8 [bit]

Parity check N/A

Stop bit 1 [bit]

X parameter Invalid

Flow control N/A

Delimiter CR LF (0D and 0A in hex)

Communication method Duplex

Serial communication specification (in setting mode)

Note:

Use the proper RS-232C cable for the connected devices.

【See: 10.1.2 RS-232C connector】


26

7.4.1 Setting transmitter

Setting transmitter

If devices other than devices on the figure above, settings of those devices will not be affected.

1 Connect devices using cables.

2 Turn on the transmitter.

3 Change the RS-232C communication mode setting from communication mode to setting

mode.

・ Set [F99] to “on” or “ALL” from the setup menu so that maintenance menu will be enabled.

・ Set [C90] to “01” from the maintenance menu.

4 Set the transmitter using commands.

【See: 9 Command】

5 Put the RS-232C communication mode back to communication mode.

・ Set [C90] to “00” from the maintenance menu.

・ Set [F99] to “oFF” from the setup menu.

Laptop

Set “C90” to “01” (9600 bps)Setting how maintenance

menu is displayed

or

RS

-23

2C

FG

DC

5V

3A

LA

UD

IO O

UT

PU

TR

POWERSTATUS

HDCP

HD

MI IN

PU

T

Tx


OP

TIC

AL

TX



KEY LOCK

－＋SET

SIG

NA

L


27

7.4.2 Setting receiver

Setting receiver

If devices other than devices on the figure above, settings of those devices will not be affected.

1 Connect devices using cables.

2 Set DIP SW1 to “ON” (setting mode).

3 Turn on the receiver.

4 Set the receiver using commands.


5 Turn off the receiver.

6 Set DIP SW1 to “OFF” (communication mode).

RS

-23

2C

FG

DC

5V

3A

POWERSTATUS

HDCP

HD

MI O

UT

PU

T

Rx


OP

TIC

AL

TX

SIG

NA

L

DIP

SW



Laptop

Set DIP SW1

to “ON”.


28

8 Menus

The following three menu types can be set in the transmitter:

・ Setting input and output in normal use: setup menu

・ Verifying operations: maintenance menu

・ Displaying I/O status: status display menu

Note:

Since the maintenance menu and status display menu are not used normally, they are not displayed.

Display those menu using setup menu as needed. Menu list

8.1 Menu list

List of setup menu

Menu

number Function

Settings Page

Setting value Default

F10 EDID SVGA to WUXGA 1080p 30

F16 No-signal input monitoring time OFF/2 to 15 [sec] 10 [sec] 32

F22 PCM Audio 32/44.1/48/88.2/96/192 [kHz] 48 [kHz] 33

F24 AC-3 Dolby Digital Audio OFF/32/44.1/48 [kHz] OFF 33

F26 AAC Audio OFF/32/44.1/48/88.2/96 [kHz] OFF 33

F28 Dolby Digital Plus Audio OFF/32/44.1/48 [kHz] OFF 34

F30 DTS Audio OFF/32/44.1/48/96 [kHz] OFF 34

F32 DTS-HD Audio OFF/44.1/48/88.2/96/

176.4/192 [kHz]

OFF 34

F34 Dolby TrueHD Audio OFF/44.1/48/88.2/96/176.4/192

[kHz]

OFF 35

F36 Audio channel 2 channels/

3 (2.1) channels/

6 (5.1) channels/

8 (7.1) channels

2 channels 35

F65 [F65] Audio output ON/OFF ON 36

F76 EDID WXGA 1360x768/1366x768 1360 x 768 36

F90 Version －－ 36

F99 Maintenance/status display menu oFF/on/ALL oFF 36


29

List of maintenance menu

Menu

number Function

Settings Page


C06 HDCP input setting On (HDCP enabled)/oFF HDCP

disabled

on 37

C55 Forced color conversion output oFF (automatic)/d (DVI)/RGB/422

(YCbCr422)/444 (YCbCr444)

oFF 38

C90 RS-232C communication mode 00 (communication mode)/

01 (setting mode; 9600 bps)

00 38

List of status display menu

Menu

number Function

Settings Page


L01 to L13 Displaying information about input －－ 39

L50 Displaying information about output －－ 42


30

8.2 Setting input and output (Setup menu)

[ ] to the left of the each section title shows its menu name.

8.2.1 [F10] EDID resolution

From the built-in EDID, you can select an EDID to be sent from the transmitter to the source device.

Set the maximum resolution according to the sink device.

Maximum EDID resolution

Setting

value

Maximum resolution Pixel Standard Remarks

03 1080p (59.94/60) 1920x1080 HDTV Default

04 720p 1280x720

05 1080i 1920x1080

06 1080p(24/25/30/50) 1920x1080

07 SVGA 800x600 VESA

08 XGA 1024x768

09 VESA720 1280x720 CVT For DVI devices

10 WXGA 1280x768 VESA

11 WXGA 1280x800 MAC supported

12 Quad-VGA 1280x960

13 SXGA 1280x1024

14 WXGA 1360x768、

1366x768

Pixels can be set using “8.2.12 [F76]

EDID WXGA”.

15 SXGA+ 1400x1050

16 WXGA+ 1440x900

17 WXGA++ 1600x900 (RB)

18 UXGA 1600x1200

19 WSXGA 1680x1050

20 VESA1080 1920x1080 CVT (RB), for DVI device input

21 WUXGA 1920x1200 VESA (RB)

(RB): Reduced Blanking

【See: 8.2.12 [F76] EDID WXGA】


31

Maximum resolution and EDID supported pixel

EDID supported

pixel

Max. resolution

640 x

480

800 x

600

1024 x

768

1280 x

720

1280 x

768

1280 x

800

1280 x

960

1280 x

1024

1360

x 768

*

1366

x 768

*

1400 x

1050

1440 x

900

1600 x

900

1600 x

1200

1680 x

1050

1920 x

1080

1920 x

1200

03 1080p(59.94/60) Y Y Y N N Y Y Y Y Y Y Y Y Y Y Y N

04 720p Y Y N Y N N N N N N N N N N N N N

05 1080i Y Y Y N N N N N N N N N N N N N N

06 1080p

(24/25/30p/50p) Y Y Y N N Y Y Y Y Y Y Y Y Y Y Y N

07 800x600 Y Y N N N N N N N N N N N N N N N

08 1024x768 Y Y Y N N N N N N N N N N N N N N

09 1280x720 Y Y Y Y N N N N N N N N N N N N N

10 1280x768 Y Y Y Y Y N N N N N N N N N N N N

11 1280x800 Y Y Y Y Y Y N N N N N N N N N N N

12 1280x960 Y Y Y Y Y Y Y N N N N N N N N N N

13 1280x1024 Y Y Y Y Y Y Y Y N N N N N N N N N

14 1360x768 Y Y Y Y Y Y Y Y Y Y N N N N N N N

15 1400x1050 Y Y Y Y N Y Y Y Y Y Y N N N N N N

16 1440x900 Y Y Y Y N Y Y Y Y Y Y Y N N N N N

17 1600x900 Y Y Y Y N Y Y Y Y Y Y Y Y N N N N

18 1600x1200 Y Y Y Y N Y Y Y Y Y Y Y Y Y N N N

19 1680x1050 Y Y Y Y N Y Y Y Y Y Y Y Y Y Y N N

20 1920x1080 Y Y Y N N Y Y Y Y Y Y Y Y Y Y Y N

21 1920x1200 Y Y Y N N Y Y Y N N Y Y Y Y Y Y Y

Y: Supported, N: Not supported

* The number of EDID-supported pixels for 1360×768 and 1366×768 can be set in “8.2.12 [F76] EDID

WXGA”. The default value is 1360×768.

【See: 8.2.12 [F76] EDID WXGA】


32

8.2.2 [F16] No-signal input monitoring time

You can set the monitoring time for when the source device does not output video signals due to the changes

of transmitter EDID or turning on/off the transmitter or source device.

Changing EDID

ON

OFF

The OPF requests the source

device to output video signals

Monitoring time

Hot plugON

OFF

Video signals from

source device

Monitoring time

Setting value

oFF: OFF

02 to 15: 2 to 15 seconds [Default: 10]

Notes:

・ If you use the power-saving function or dual monitor of the PC (source device), set this menu to “OFF”.

PCs may release or cancel those functions if they receive the request to output video signals.

・ If the set time is shorter than the timing that the source device outputs video, the source device may not

output video signals because it sets the output signals repeatedly. In these cases, set the monitoring time

longer.

Changing EDID

Monitoring

time

ON

OFF

Monitoring

time

Monitoring

time

Video output timing of source device

Video signals

from source

device

OPF requests source device to output

video signals


33

8.2.3 [F22] PCM Audio

You can set the maximum sampling frequency of PCM Audio output from the source device.

Setting value

32: 32 kHz

44: 44.1 kHz

48: 48 kHz [Default]

88: 88.2 kHz

96: 96 kHz

192: 192 kHz

Note:

For LCD monitors and the like, some audio formats are not supported. Select the audio format and sampling

frequency that are supported by the connected devices.

8.2.4 [F24] AC-3 Dolby Digital Audio

You can set the maximum sampling frequency of AC-3 Dolby Digital Audio that is output from the source

device.

Setting value

32: 32 kHz

44: 44.1 kHz

48: 48 kHz

oFF: OFF [Default]

Note:



8.2.5 [F26] AAC Audio

You can set the maximum sampling frequency of AAC Audio that is output from the source device.

Setting value

32: 32 kHz

44: 44.1 kHz

48: 48 kHz

88: 88.2 kHz

96: 96 kHz

oFF: OFF [Default]

Note:




34

8.2.6 [F28] Dolby Digital Plus Audio

You can set the maximum sampling frequency of Dolby Digital Plus Audio that is output from the source

device.

Setting value

32: 32 kHz

44: 44.1 kHz

48: 48 kHz

oFF: OFF [Default]

Note:



8.2.7 [F30] DTS Audio

You can set the maximum sampling frequency of DTS Audio that is output from the source device.

Setting value

32: 32 kHz

44: 44.1 kHz

48: 48 kHz

96: 96 kHz

oFF: OFF [Default]

Note:



8.2.8 [F32] DTS-HD Audio

You can set the maximum sampling frequency of DTS-HD Audio that is output from the source device.

Setting value

44: 44.1 kHz

48: 48 kHz

88: 88.2 kHz

96: 96 kHz

176: 176.4 kHz

192: 192 kHz

oFF: OFF [Default]

Note:




35

8.2.9 [F34] Dolby TrueHD Audio

You can set the maximum sampling frequency of Dolby TrueHD Audio that is output from the source device.

Setting value

44: 44.1 kHz

48: 48 kHz

88: 88.2 kHz

96: 96 kHz

176: 176.4 kHz

192: 192 kHz

oFF: OFF [Default]

Note:



8.2.10 [F36] Audio channel

You can set the number of channels to the audio of multi-channel output that is from the source device.

Setting value

02: 2 channels [Default]

03: 3 channels (2.1channels)



■ The number of channels and speaker configuration

RL

RLC RRC

RR

FR

ＦＣ

FL

LFE

FL : Front Left

FC : Front Center

FR : Front Right

RL : Rear Left

RR : Rear Right

RLC : Rear Left Center

RRC : Rear Right Center

LFE : Low Frequency Effect

Number of speakers FL/FR LFE FC RL/RR RLC/RRC

2 (2 channels) ON OFF OFF OFF OFF

3 (2.1 channels) ON ON OFF OFF OFF

6 (5.1 channels) ON ON ON ON OFF

8 (7.1 channels) ON ON ON ON ON

The number of channels and speaker configuration


36

8.2.11 [F65] Audio output

You can set ON/OFF of audio output from the output connector for extension.

Setting value

on: ON [Default]

oFF: OFF

Note:

Even if you set this menu to “oFF”, audio is output from the audio output connector.

8.2.12 [F76] EDID WXGA

If you select an EDID that includes WXGA in “8.2.1 [F10] EDID resolution”, you can select a number of pixels

of WXGA (1366 or 1360).

【See: 8.2.1 [F10] EDID resolution】

Setting value

on: 1366x768

oFF: 1360x768 [Default]

8.2.13 [F90] Version

You can display the firmware version.

8.2.14 [F99] Maintenance/status display menu

You can set how the maintenance menu and status display menu are displayed.

Setting value

oFF: not displayed [Default]

on: displayed (not displayed when the OPF-H1000D is turned on next time)

ALL: always displayed (displayed when the OPF-H1000D is turned on next time as well)


37

8.3 Verifying operation (Maintenance menu)

You can set the required items for operation verification.

Set [F99] to “ALL” or “on” in order to enable the maintenance menu.

【See: 8.2.14 [F99] Maintenance/status display menu】

8.3.1 [C06] HDCP input setting

You can set whether the transmitter encrypts HDCP to the source device.

Some source devices check whether the connected device supports HDCP and then determine whether they

encrypt HDCP signals or not. Since the transmitter is HDCP compliant, if it is connected to a sink device that

is not HDCP compliant, the sink device may not display video. In this case, set this menu to “oFF” in order to

display the video.

RS

-23

2C

FG

DC

5V

3A

LA

UD

IO O

UT

PU

TR

POWERSTATUS

HDCP

HD

MI IN

PU

T

Tx


OP

TIC

AL

TX



KEY LOCK

－＋SET

SIG

NA

L

RS

-23

2C

FG

DC

5V

3A

POWERSTATUS

HDCP

HD

MI O

UT

PU

T

Rx


OP

TIC

AL

TX

SIG

NA

LD

IP S

W



RS

-23

2C

FG

DC

5V

3A

LA

UD

IO O

UT

PU

TR

POWERSTATUS

HDCP

HD

MI IN

PU

T

Tx


OP

TIC

AL

TX



KEY LOCK

－＋SET

SIG

NA

L

RS

-23

2C

FG

DC

5V

3A

POWERSTATUS

HDCP

HD

MI O

UT

PU

T

Rx


OP

TIC

AL

TX

SIG

NA

LD

IP S

W



HDCP-

compliant

PC

Without

copyright

protection

With copyright

protection HDCP input

setting: on

Video cannot be

displayed

Video can be displayed

HDCP-non-compliant

sink device

HDCP-compliant/non-

compliant sink device

HDCP-compliant sink

device

Transmitter Receiver

Receiver

HDCP input

setting: oFF

Video can be displayed

Transmitter

HDCP and sink devices

Setting value

on: HDCP enabled [Default]

oFF: HDCP disabled

Note:

Set this menu to “on” in order to display copyright protected contents.


38

8.3.2 [C55] Forced color conversion output

You can set the color space to be sent to the sink device.

Normally the sink device automatically select a proper color space for display according to the color space of

input video. However, if a sink device cannot select a color space for some reason, use this menu in order to

set the color space.

Setting value

rgb: RGB output

422: YCbCr422 output

444: YCbCr444 output

d: DVI output

oFF: automatic [Default]

8.3.3 [C90] RS-232C communication mode

Set the RS-232C communication mode in order to control the transmitter using commands.


Setting value

00: communication mode [Default]

01: setting mode (9600 bps)


39

8.4 Displaying I/O status (status display menu)

Displaying I/O status of the transmitter.

This menu is valid if [F99] is set to “on” or “ALL”.

Press the “SET” button in order to finish the operation.

【See: 8.2.14 [F99] Maintenance/status display menu】

8.4.1 [L01 to L13] Displaying information about input

Input information of transmitter

Menu number Value Description

HDMI/DVI mode and color depth of input video

L01 H08 HDMI mode 24 bit/pixel (8 bit/component)

H10 HDMI mode 30 bit/pixel (10 bit/component)

H12 HDMI mode 36 bit/pixel (12 bit/component)

d08 DVI mode 24 bit/pixel (8 bit/component)

- - - Nothing is input

Presence or absence of HDCP of input video

L02 on With HDCP

oFF Without HDCP


Presence or absence of HDCP encryption of input video (encryption from the source side)

L03 on With encryption

oFF Without encryption


Color space of input video

L04 rgb RGB

422 YCbCr 422

444 YCbCr 444

- - - Unknown or nothing is input

Input video frequency

L05 59.9 Input vertical synchronous frequency (e.g. 59.9 Hz)


DDC power input status

L06 on With DDC power supply

oFF Without DDC power supply

Input resolution

L07 192 Input resolution (scrolling display)



40


Audio input format (2 digits from left) and the number of channels (1 digit from right)

X= the number of channels:1 = 2 channels, 2 = 2.1 channels, 5 = 5.1 channels,

7 = 7.1 channels

L10 - - - Unknown or nothing is input

00X Unknown

01X PCM Audio

02X AC-3 Audio

03X MPEG-1 Audio

04X MP3 Audio

05X MPEG-2 Audio

06X AACLC Audio

07X DTS Audio

08X ATRAC Audio

09X DSD Audio

10X Dolby Digital Plus Audio

11X DTS-HD Audio

12X Dolby TrueHD Audio

13X DST Audio

14X WMA Audio

15X HE-AAC / HE-AACv2 / MPEG Surround Audio

Audio input sampling frequency

L11 22 22.05 kHz

24 24 kHz

32 32 kHz

44 44.1 kHz

48 48 kHz

88 88.2 kHz

96 96 kHz

176 176.4 kHz

192 192 kHz

768 768 kHz

_01 Unknown

_05

_07

_11

_13

_15


The number of audio input bits, HBR mode (High Bit-Rate Audio)

L12 H16 16 bit, HBR mode

P16 16 bit, PCM mode

: :

H24 24 bit、HBR mode

P24 24 bit、PCM mode



41


Audio input status

L13 000 No audio input

001 Being detected the input

002

003

004

005

006 Normal input



42

8.4.2 [L50] Displaying information about output

Output information of transmitter


Color space and output status

L50 rgb RGB output

422 YCbCr422 output

444 YCbCr444 output

- - - Not connected


43

9 Command

You can set the transmitter and receiver using the RS-232C connector. Setting mode need to be set for the

target device (transmitter or receiver); see “7.4 Setting transmitter and receiver using setting mode” for

details.

【See: 7.4 Setting transmitter and receiver using setting mode】

9.1 Command outline

Each command consists of 3-byte character (case ignored) following “@” (“40” in hex) and a parameter

(one-byte number). Some commands do not need a parameter or can specify several parameters.

Commands can be run by sending the delimiter, (CR+LF; “0D+0A” in hex).

Example: @SPM,2

“,” (“2C” in hex) is the delimiting character between a command and parameter and between parameters.

9.2 Command list

Error status

Command Function Page

@ERR Error status 44

Setting command


@GPM / @SPM Setting time for ignoring video output request signals:

Hot Plug mask off setting (only receiver)

45

@GIV Acquiring version information 45

Status acquire command


@GIS Acquiring input status 46

@GOS Acquiring output status 47


44

9.3 Command description

9.3.1 Error status

@ERR Error status

Function Acquisition

Format Only return value

Return value

format

@ERR, error

Parameter error: error status

1 = There is an error in the parameter format or value.

2 = Undefined command or there is an error in the command format.

5 = Being set using menu (for transmitter).

Example GIS

@ERR,2

Sends the @GIS command.

There is an error in the command format.

Related info. －


45

9.3.2 Setting command

@GPM / @SPM Setting time for ignoring video output request signals: Hot Plug mask off setting

(only receiver)

Function Acquisition Setting

Format @GPM @SPM, time

Return value

format

@GPM, time @SPM, time

Parameter time: If the request signals are repeated in a short cycle, video may not be output. This

problem can be solved by setting the ignoring time.

0 = OFF [Default]

2 to 15 = 2 to 15 seconds

Example @GPM

@GPM,0

Acquires the current setting status.

The setting is OFF.

@SPM,2

@SPM,2

Sets the ignoring time to 2 seconds.

The setting has been changed to 2 seconds.

Related info. －

@GIV Acquiring version information


Format @GIV

Return value

format

@GIV, id, ver

Parameter id: model name

ver: firmware version

Example @GIV

@GIV,OPF-RH1000D ,1.00

Acquires the version information of the firmware.

The firmware version of the OPF-RH1000D is

ver.1.00. (for transmitter, the firmware version of

the “OPF-TH1000D” will be returned.)

Related info. 8.2.13 [F90] Version


46

9.3.3 Status acquisition command

@GIS Acquiring input status


Format @GIS, mode

Return value

format

@GIS, mode (, status1, status2, status3, status4, status5, status6, status7, status8,

status9, status10, status11)

Parameter mode: selecting item

0 = selecting all items (information of status1 to status11)

1 to 11 = selecting items from status1 to status11

status1: Input video HDMI/DVI mode and color depth

HDMI mode = HDMI/DVI/－

Color depth = 8bit/10bit/12bit/－

status2: presence or absence of input video HDCP

on/off/－

“-” is always returned for the receiver.

In order to check whether HDCP is input, see the HDCP status LED.

status3: presence or absence of input video HDCP authorization (authorization from

the source device)

on/off/－

“-” is always returned for the receiver.

In order to check whether HDCP is input, see the HDCP status LED.

status4: color space of input video

RGB/YCbCr444/YCbCr422/Future (for expansion)/－

status5: input video frequency

[Frequency] Hz/－

status6: DDC power supply input status

on/off/－

status7: Input resolution, vertical synchronous frequency

[Horizontal resolution] x [Vertical resolution] p/i

[Vertical synchronous frequency] Hz/－

status8: audio input format and the number of channels

Format = #00 to #15/－ see “8.4.1 L10” for details.

The number of channels = 2ch/2.1ch/5.1ch/7.1ch/－

status9: audio input sampling frequency

22.05kHz/24kHz/32kHz/44.1kHz/48kHz/88.2kHz/96kHz/

176.4kHz/192kHz/768kHz/－

status10: the number of audio input bits, HBR mode (High Bit-Rate Audio)

HBR mode = HBR/PCM/－

The number of quantized bits = 16bit to 24bit

status11: audio input status

#0 to #6/－ see “8.4.1 L13” for details.

Example @GIS,7

@GIS,7,1920x1080p 60.0Hz

Acquires the input status of status 7.

The resolution is 1920x1080p and frequency is

60.0Hz.

Related info. 8.4.1 [L01 to L13] Displaying information about input


47

@GOS Acquiring output status


Format @GOS, mode

Return value

format

@GOS, mode (, status1, status2, status3, status4, status5, status6, status7)

Parameter mode: selecting item

0 = selecting all items (information of status1 to status7)

1 to 7 = selecting items from status1 to status7

status1: Deep Color of the sink device

8bit/10bit/12bit/16bit/－

status2: HDMI and audio of the sink device

HDMI = HDMI/DVI/－

Audio = PCM/Audio Compression supported/－

status3: Color space of the sink device

RGB/YCbCr444/YCbCr422/－

status4: status of HDCP authorization with connected monitor

#0 = no HDCP

#1 to #3 = being authorized

#4 and #5 = authorization ends normally

#－ = any monitor is connected

status5: color space

RGB/YCbCr444/YCbCr422/－

status6: HDCP of the sink device

HDCP supported/HDCP not supported/－

status7: Hot plug Detect

on/off

Example @GOS,2

@GOS,2,HDMI PCM

Acquires the output status of status2.

The output status of status2 is HDMI and PCM.

Related info. 8.4.2 [L50] Displaying information about output


48

10 Specification

10.1 Pin assignments

10.1.1 HDMI Type A connector

Pin # Signal name Pin # Signal name

1 TMDS data 2+ 10 TMDS clock+

2 TMDS data 2 shield 11 TMDS clock shield

3 TMDS data 2- 12 TMDS clock

4 TMDS data 1+ 13 CEC

5 TMDS data 1 shield 14 spare (N.C.*)

6 TMDS data 1- 15 SCL

7 TMDS data 0+ 16 SDA

8 TMDS data 0 shield 17 DDC / CEC ground

9 TMDS data 0- 18 +5 power supply

19 Detecting hot plug

*N.C.: No Connection

HDMI Type A configuration

10.1.2 RS-232C connector

Male D-sub (9-pin)

RS-232C connector

1 5

6 9

RS-232C connector pin assignments

1

2

19

18


49

■ Connecting OPF-H1000D to PC

Use a cross cable to connect the OPF-H1000D to a PC.

RD

TD

N.C.

N.C.

N.C.

N.C.

GND

RTS

CTS

Pin #

1

3

2

4

6

5

7

9

8

Signal

　 RD

　 TD

　 N.C.

　 N.C.

　 N.C.

　 N.C.

　 GND

　 RTS

　 CTS

Signal

(Receive Data)

(Transmit Data)

(Ground)

(Request to Send)

(Clear to Send)

OPF-H1000D PC

(Not Connected)*

(Not Connected)*

(Not Connected)*

(Not Connected)*

*Not used

RS-232C pin assignment (connecting to PC)

■ Connecting OPF-H1000D to IDK’s products

Use a cross cable to connect the OPF-H1000D to an IDK’s product.

RD

TD

N.C.

N.C.

N.C.

N.C.

GND

RTS

CTS

Pin #

1

3

2

4

6

5

7

9

8

Signal

　 RD

　 TD

　 N.C.

　 N.C.

　 N.C.

　 N.C.

　 GND

　 RTS

　 CTS

Signal

(Receive Data)

(Transmit Data)

(Ground)

(Request to Send)

(Clear to Send)

OPF-H1000D IDK s products

(Not Connected)*

(Not Connected)*

(Not Connected)*

(Not Connected)*

*Not used

RS-232C pin assignment (connecting to IDK’s product)

■ Connecting OPF-H1000D to another device requiring straight connection

Use a straight cable to connect the OPF-H1000D to other devices requesting straight connection.

RD

TD

N.C.

N.C.

N.C.

N.C.

GND

RTS

CTS

Pin #

1

3

2

4

6

5

7

9

8

Signal

　 TD

　 RD

　 N.C.

　 N.C.

　 N.C.

　 N.C.

　 GND

　 CTS

　 RTS

Signal

(Receive Data)

(Transmit Data)

(Ground)

(Request to Send)

(Clear to Send)

OPF-H1000D Other deivces

(Not Connected)*

(Not Connected)*

(Not Connected)*

(Not Connected)*

*Not used

RS-232C pin assignment (Connecting to device requiring straight connection)


50

10.2 Product specification

10.2.1 OPF-H1000D

Item OPF-TH1000D (Transmitter) OPF-RH1000D (Receiver)

Input

1 input HDMI (*1)/DVI 1.0 TMDS single link, HDCP 1.4 Connector: Female HDMI Type A (19-pin) (*2)

1 input Digital optical signal for extension RS-232C

Output

1 output Digital optical signal for extension RS-232C

1 output Digital optical signal for daisy chain

1 output HDMI (*1)/DVI 1.0 TMDS single link, HDCP 1.4 Connector: Female HDMI Type A (19-pin) (*2)

Format

VGA / SVGA / XGA / WXGA(1280x768) / WXGA(1280x800) / Quad-VGA / SXGA / WXGA(1360x768) / WXGA(1366x768) / SXGA+ / WXGA+ / WXGA++ / UXGA / WSXGA+ / WUXGA

For WUXGA, only Reduced Blanking is supported. 480i / 480p / 576i / 576p / 720p / 1080i / 1080p

Color depth 24 bit (*3)

Dot clock 25 MHz to 165 MHz

TMDS clock 25 MHz to 165 MHz

Plug & Play DDC2B (Built-in EDID) Max. resolution selectable using built-in EDID

Digital audio input/output Multi-channel LPCM up to 8 channels Sampling frequency: 32 kHz to 192 kHz, Sample size: 16 bit to 24 bit Reference level: -20 dBFS, Max. input/output level: 0 dBFS

Analog audio output

1 output Unbalanced Stereo LR Output impedance: 75 Ω Reference level: -10 dBu, Max. output level: +10 dBu Connector: Stereo mini jack (3.5 mm)

-

Cable for extension

Cable Simplex fiber cable, SFP optical transceiver (2 LC connectors)

Polishing (*4) SFP optical transceiver for Multimode : PC polishing (Recommended) SFP optical transceiver for Singlemode : UPC polishing (Recommended), SPC *APC is not supported

Transmission distances (*5)

Multimode fiber (OM3) : Up to 984 ft. (300 m) Multimode fiber (OM4) : Up to 0.62 mi. (1 km) Singlemode fiber (OS1) : Up to 2.92 mi. (4.7 km) Singlemode fiber (OS1) : Up to 6.21 mi. (10 km, optional)

Control RS-232C 1 port/male D-sub (9-pin) simplex, up to 115.2 kbps

General

AC adapter Input : 100 - 240 VAC ±10%, 50 Hz/60 Hz ±3 Hz Output : DC 5 V 3 A (A dedicated AC adapter is provided)

Power consumption

About 9 Watts About 8 Watts

Dimensions 4.2 × 1.1 × 7.9” (106 (W) × 28 (H) × 200 (D) mm) (Quarter rack wide, thin type) (Excluding connectors and the like)

4.2 × 1.0 × 7.9” (106 (W) × 26 (H) × 200 (D) mm) (Quarter rack wide, thin type) (Excluding connectors and the like)

Weight 1.3 lbs. (0.6 kg) 1.3 lbs. (0.6 kg)

Temperature Operating : 32°F to 104°F (0°C to +40°C) Storage : -4°F to +176°F (-20°C to +80°C)

Humidity Operating/Storage: 20% to 90% (Non Condensing)

*1 HEC and ARC are not supported. *2 Use 16.4 ft. (5 m) or shorter HDMI cables. *3 Deep Color is not supported. *4 It is possible to connect without using the recommended polishing method, but that may cause a change of transmission distance ability due to an increase in return loss. *5 The maximum transmission distance is measured under the following conditions: Fiber that is polished by a recommended method is used, there is no interconnection, and the

allowable bending radius is not exceeded.

10.2.2 SFP Specification

Item Multimode fiber Singlemode fiber

Wave length 850 nm (Oxide VCSEL laser*) 1310 nm (Fabry-Perot laser*)

Max. transmission distances OM3 : 984 ft. (300 m) OM4 : 0.62 mi. (1 km)

OS1: 2.92 mi. (4.7 km) OS1: 6.21 mi. (10 km, optional)

Receiver sensitivity (OMA) @10.3Gbps -13 dBm or higher -18 dBm or higher

Average Launch Power -9 dBm to -2.5 dBm -8.4 dBm to -3 dBm

Max. input power 0 dBm 0 dBm

Connector LC (Duplex)

*The lasers in these models meet class1.


51

11 Troubleshooting

In case the OPF-H1000D does not work correctly, please check the following items first. Also refer to manuals

for connected devices as well, since they may possibly be the cause of the problem.

・ Are the OPF-H1000D and all devices plugged in and powered on normally?

・ Are cables connected correctly?

・ Are there no loose connections?

・ Are correct cables for OPF-H1000D being used?

・ Are signal specifications of connected devices matched to each other?

・ Are settings of the sink device correct?

・ Are there any nearby objects that may cause noise?

If additional assistance is required, please perform the following tests and then contact us.

No. Checking items Result

1 The problem occurs at all connectors? Yes or No

2 Connect the devices using genuine cables without connecting the OPF-H1000D.

The problem still cannot be solved? Please contact us for assistance.

Yes or No


52

User Guide/Command Guide of OPF-TH1000D/OPF-RH1000D

Ver.1.10.0

Issued on: 6 July 2020

Information in this document is subject to change without notice. All rights reserved. All trademarks mentioned are the property of their respective owners.

Headquarters IDK Corporation

7-9-1 Chuo, Yamato-shi, Kanagawa-pref.

242-0021 JAPAN

TEL: +81-46-200-0764 FAX: +81-46-200-0765

Email: [email protected] URL: http: //www.idkav.com

USA

IDK America Inc.

72 Grays Bridge Road Suite 1-C, Brookfield, CT 06804

TEL: +1-203-204-2445


Europe

IDK Europe GmbH

Lise-Meitner-Str. 6, D-40878 Ratingen

TEL: +49-2102-578-301-0


Product information

Support

Arvanics Corporation

7-9-1 Chuo, Yamato-shi, Kanagawa-pref.

242-0021 JAPAN

TEL: +81-46-259-6920 FAX: +81-46-259-6930

Email: [email protected] URL: http: //www.arvanics.com

mailto:[email protected]






http://www.arvanics.com/

Documents

HDMI Fiber Optic Cable Extender OPF-TH1000D/OPF-RH1000Didkav.com/wp-content/uploads/2020/07/OPF-H1000D...HDMI cable fixing hole Hole for the attached cable clamp to secure an HDMI