HOME THEATER RECEIVER RX-F10S - JVC USAresources.jvc.com/Resources/00/00/93/LVT1163-001A.pdf · LVT1163-001A [J] RX-F10S HOME THEATER RECEIVER INSTRUCTIONS For Customer Use: Enter

LVT1163-001A[J]

RX-F10SHOME THEATER RECEIVER

INSTRUCTIONSFor Customer Use:

Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference.

Model No.

Serial No.

cover_RX-F10S[J]_f.p65 04.4.22, 15:263

Warnings, Cautions, and OthersMises en garde, précautions et indications diverses

Caution–– STANDBY/ON button!Disconnect the mains plug to shut the power off completely. The

STANDBY/ON button in any position does not disconnect themains line. The power can be remote controlled.

Attention—Touche STANDBY/ON!Déconnectez la fiche d’alimentation secteur pour couperl’alimentation complètement. La touche STANDBY/ON,dans n’importe quelle position, ne déconnecte pas le systèmedu secteur. L’alimentation ne peut pas être télécommandé.

For Canada/pour Le CanadaTHIS DIGITAL APPARATUS DOES NOT EXCEED THECLASS B LIMITS FOR RADIO NOISE EMISSIONS FROMDIGITAL APPARATUS AS SET OUT IN THEINTERFERENCE-CAUSING EQUIPMENT STANDARDENTITLED “DIGITAL APPARATUS,” ICES-003 OF THEDEPARTMENT OF COMMUNICATIONS.CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DEBRUITS RADIOELECTRIQUES APPLICABLES AUXAPPAREILS NUMERIQUES DE CLASSE B PRESCRITESDANS LA NORME SUR LE MATERIEL BROUILLEUR;“APPAREILS NUMERIQUES”, NMB-003 EDICTEE PAR LEMINISTRE DES COMMUNICATIONS.

Note to CATV system installer:This reminder is provided to call the CATV system installer’sattention to Section 820-40 of the NEC which providesguidelines for proper grounding and, in particular, specifiesthat the cable ground shall be connected to the groundingsystem of the building, as close to the point of cable entry aspractical.

CAUTIONTo reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.2. Do not expose this appliance to rain or moisture.

ATTENTIONAfin d’éviter tout risque d’électrocution, d’incendie, etc.:

1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir lecoffret de l’appareil.

2. Ne pas exposer l’appareil à la pluie ni à l’humidité.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCKDO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION

For Canada/pour le Canada

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERTATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND

For U.S.A

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.

safety_RX-F10S[J]_f.p65 04.4.22, 15:261

1

Table of Contents

Parts identification ................................................ 2

Getting started ...................................................... 4Before Installation .................................................................. 4Checking the supplied accessories ....................................... 4Putting batteries in the remote control ................................... 4Connecting the FM and AM antennas ................................... 5Connecting the speakers ....................................................... 6Connecting video components .............................................. 7Connecting the power cord .................................................. 11

Basic operations ................................................. 121 Turn on the power ............................................................ 122 Select the source to play .................................................. 123 Adjust the volume ............................................................ 13Selecting the digital decode mode ....................................... 13Adjusting the subwoofer audio position ............................... 14Activating TV Direct ............................................................. 14Turning off the sounds temporarily ...................................... 15Changing the display brightness .......................................... 15Turning off the power with the Sleep Timer ......................... 15

Basic settings ...................................................... 16Setting the speaker information automatically

—Smart Surround Setup ............................................... 16Basic setting items ............................................................... 17Operating procedure ............................................................ 18Setting the speakers ............................................................ 18Setting bass sound .............................................................. 19Activating the EX/ES setting—EX/ES .................................. 20Selecting the main or sub channel—DUAL MONO ............. 20Using the Midnight mode—MIDNIGHT M. ........................... 20Setting the digital input (DIGITAL IN) terminals

—DIGITAL IN1/2/3 ......................................................... 21Setting Auto Surround—AUTO SURRND ............................ 21Selecting the component video input mode

—DVD VIDEO/VCR VIDEO ........................................... 21

Sound adjustments ............................................. 22Basic adjustment items ........................................................ 22Operating procedure ............................................................ 22Adjusting speaker output level ............................................. 23Adjusting the sound parameters for the

Surround/DSP modes ................................................... 23Adjusting the bass sounds ................................................... 24Adjusting the equalization patterns

—D EQ 63Hz/250Hz/1kHz/4kHz/16kHz........................ 24

Tuner operations ................................................. 25Tuning in to stations manually .............................................. 25Using preset tuning .............................................................. 25Selecting the FM reception mode ........................................ 26

Creating realistic sound fields ........................... 27Reproducing theatre ambience ........................................... 27Introducing the Surround modes ......................................... 27Introducing the DSP modes ................................................. 29Using the Surround/DSP modes ......................................... 30Activating the Surround/DSP modes ................................... 31

AV COMPU LINK remote control system .......... 32

Operating other JVC products ........................... 34Operating other manufacturers’ products ........ 36

Troubleshooting .................................................. 39

Specifications ...................................................... 40

01-05RX-F10S[J]_f.p65 04.4.22, 15:251

2

7

2

3

i

5

6

o

1

4

8

9

w

e

d

s

a;

u

rt

y

pq

Remote controlSee pages in parentheses for details.

1 TV DIRECT button (14)2 Standby/on buttons (12, 14, 34 – 38)

AUDIO, DVR/DVD , VCR , DBS , TV 3 Source selecting buttons (12, 14, 25, 34, 36 – 38)

DVR/DVD, VCR, DBS, TV, DVD MULTI, FM/AM4 TV VOL (volume) +/– button (34, 36)5 CHANNEL +/– button (34 – 38)6 • Operating buttons for video components (34, 35, 37, 38)

4, 3, ¢, 1, 7, 8, ¡• Operating buttons for tuner (25, 26)

( TUNING, FM MODE, TUNING 9, MEMORY7 Operating buttons for DVD recorder or DVD player* (35, 38)

TOP MENU, MENU, cursor buttons (3, 2, 5, ∞), ENTER,ON SCREEN

8 SMART SURROUND SETUP button (16)9 Operating buttons for DVD recorder or DVD player* (35)

fs/Rate, AUDIO, SUBTITLE, SET UP, DVD/HDD,TITLE/GROUP, , ZOOM, , VFP, PROGRESSIVE,ANGLE

p • EX/ES button (20)• RETURN* button (35)

q SOUND button (13, 14, 20, 23, 24)w SURROUND button (31)e • Adjusting buttons for speaker and subwoofer output levels

(23)FRONT L +/–, FRONT R +/–, CENTER +/–, SUBWFR +/–,SURR L +/–, SURR R +/–, S.BACK +/–

• Operating buttons for DVD recorder or DVD player* (35)THUMBNAIL, SLIDE, 3D/S.EFFECT, PAGE

r TV/VIDEO button (34, 36)t MUTING button (15)y VOLUME +/– button (13)u Mode selector (12, 14, 16, 20, 23 – 25, 31, 34 – 38)

DVR, DVD, AUDIO/TV/VCR/DBSi • Numeric buttons (26, 34 – 38)

• Adjusting buttons (13, 14, 20, 23, 24)DECODE, EQ FREQ, BASS BOOST, C.TONE,EQ LEVEL +, MIDNIGHT, EFFECT, EQ LEVEL –,A.POSITION

• TV RETURN button (34)o Operating buttons for DVD recorder or DVD player* (35)

CANCEL, DVD/CARD, REC MODE, REC PAUSE; • DISPLAY* button (35)

• DIMMER button (15, 35)a ANALOG/DIGITAL INPUT button (12)s TEST TONE button (23)d SLEEP button (15)

* These buttons can be used for operating a JVC DVD recorderor DVD player with the mode selector set to “DVR” or “DVD”(see page 35).If these buttons do not function normally, use the remote controlsupplied with your DVD recorder or DVD player. Refer also tothe manuals supplied with the DVD recorder or DVD player fordetails.

• When operating the receiver, set the mode selector (u)to “AUDIO/TV/VCR/DBS.”

• When operating a JVC DVD recorder, set the modeselector (u) to “DVR.”

• When operating a JVC DVD player, set the mode selector(u) to “DVD.”

Parts identificationP

arts

iden

tifi

cati

on

To open the cover of theremote control, push herethen slide downward.

01-05RX-F10S[J]_f.p65 04.4.22, 16:132

3

Front panel

1 STANDBY/ON button and standby lamp (12, 14)2 Display window (see below)3 Source lamps

DVD MULTI, DVR/DVD, VCR, DBS, TV, FM/AM4 • SOURCE SELECTOR (12, 14, 26)

• MULTI JOG (18, 22, 26, 31)5 MASTER VOLUME control (13)6 Remote sensor (4)

7 TV DIRECT button (14)8 SETTING button (18)9 ADJUST button (22)p SURROUND button (31)q • SET button (18, 22)

• TUNER PRESET button (26)w PHONES jack (13)

Display window

1 EQ indicator (24)2 C.TONE indicator (23)3 VIRTUAL SB indicator (30)4 indicator (27, 29)5 AUDIO P. (position) indicator (14)6 NEO:6 indicator (28)7 BASS indicator (24)8 Tuner operation indicators (25)

TUNED, ST (stereo)9 AUTO MUTING indicator (26)0 SLEEP indicator (15)

1 Power cord (11)2 ANTENNA terminals (5)3 AV COMPU LINK-III terminals (32)4 DVD MULTI IN jacks (8)

SUBWOOFER, CENTER, SURR-R, SURR-L5 DIGITAL OUT terminal (11)6 DIGITAL IN terminals (11)

• Coaxial: 1(DVR/DVD)• Optical: 2(DBS), 3(VCR)

7 COMPONENT VIDEO (Y, PB, PR) jacks (7 – 10)MONITOR OUT, DVR/DVD IN, VCR IN

Rear panel

See pages in parentheses for details.

- ATT (attenuator) indicator (24)= Digital signal format indicators (13, 27, 28)

LPCM (Linear PCM), DOLBY D (Dolby Digital), DTS, 96/24~ Signal and speaker indicators (15)! DSP indicator (28, 29)@ AUTO SR (surround) indicator (21)# 3D indicator (28, 29)$ Main display% Frequency unit indicators

MHz (for FM station), kHz (for AM station)^ HP (headphones) indicator (13, 28, 29)

8 AUDIO jacks (7 – 10)• Input: DVR/DVD IN (PLAY), VCR IN (PLAY), DBS IN, TV IN• Output: DVR OUT (REC), VCR OUT (REC), MONITOR OUT

9 VIDEO terminals (7 – 10)VIDEO (composite video) jacks, S-VIDEO terminals• Input: DVR/DVD IN (PLAY), VCR IN (PLAY), DBS IN• Output: DVR OUT (REC), VCR OUT (REC), MONITOR OUT

p SUBWOOFER OUT jack (6)q SPEAKERS terminals (6)

FRONT, CENTER, SURROUND, SURROUND BACK

Par

ts id

enti

fica

tio

n

RX-F10 HOME THEATER RECEIVER

TV DIRECT SETTING ADJUST SURROUND

DVD MULTI DVR/DVD VCR DBS FM/AMTV

SOURCESELECTOR/ MULTI JOG

MASTER VOLUME

STANDBY / ON SET/TUNER PRESET

PHONES

4 5 6

q w7 8 9 p

321

EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE

C RDOLBY DDTS AAC96 / 24 AUTO SR

C.TONE VIRTUAL SB AUDIO P. BASS TUNED ST SLEEPAUTO MUTING AUTO MODEATTHPMHzkHz

1 2 3 5 87

^# $! @= ~ %

4 6 -09

TVVCR DBS

AVCOMPU LINK-III

INININ

(PLAY)OUT

(REC)DVR

OUT (REC)DVR/DVDIN (PLAY)

MONITOROUT

VIDEO

DBSIN

VCR MONITOROUT

VIDEO

OUT(REC)

IN(PLAY)

PCM/STREAM

SURR-LSURR-RCENTERSUBWOOFER

S-VIDEO

SUBWOOFEROUT

DIGITAL IN

DIGITAL OUT

DVD MULTI IN

2(DBS)3(VCR) 1(DVR/DVD) CAUTION: SPEAKERIMPEDANCE 6 ~ 16

ANTENNA

AUDIO COAXIAL

AM LOOPFM 75

AM EXT

DVR/DVDIN (PLAY)

DVROUT (REC)

CENTER SURROUND SURROUNDBACK SPEAKERS

LEFTRIGHT LEFTRIGHT

FRONTY PB PR

L

R

COMPONENT VIDEO

MONITOROUT

DVR/DVDIN

VCRIN

1

p7 9 q

2 3 654

8

01-05RX-F10S[J]_f.p65 04.4.22, 15:253

4

Getting startedG

etti

ng

sta

rted

Before InstallationGeneral precautions• Be sure your hands are dry.• Turn the power off to all components.• Read the manuals supplied with the components you are going

to connect.

Locations• Install the receiver in a location that is level and protected from

moisture and dust.• The temperature around the receiver must be between –5˚C

and 35˚C (23˚F and 95˚F).• Make sure there is good ventilation around the receiver. Poor

ventilation could cause overheating and damage the receiver.• Leave sufficient distance between the receiver and the TV.

Handling the receiver• Do not insert any metal object into the receiver.• Do not disassemble the receiver or remove screws, covers, or

cabinet.• Do not expose the receiver to rain or moisture.• Do not pull on the power cord to unplug the cord. When

unplugging the cord, always grasp the plug so as not to damagethe cord.

• When you are away on travel or otherwise for an extendedperiod or time, remove the plug from the wall outlet. A smallamount of power is always consumed while the power cord isconnected to the wall outlet.

The receiver has a built-in cooling fan which operateswhile the receiver is turned on. Be sure to leave enoughventilation to obtain sufficient cooling effect.

CAUTION:

Do not connect the AC power plug to the wall outlet until allconnections are completed.

Checking the supplied accessoriesCheck to be sure you have all of the following suppliedaccessories. If anything is missing, contact your dealerimmediately.

• Remote control (× 1)• Batteries (× 2)• AM loop antenna (× 1)• FM antenna (× 1)• Digital coaxial cable (× 1)

To operate the receiver, set themode selector to“AUDIO/TV/VCR/DBS.”

1 2 3

Putting batteries in the remote controlBefore using the remote control, put two supplied batteries first.

1 Press and slide the battery cover on the backof the remote control.

2 Insert batteries.Make sure to match the polarity: (+) to (+) and (–) to (–).

3 Replace the cover.

If the range or effectiveness of the remote control decreases,replace the batteries. Use two R6(SUM-3)/AA(15F) type dry-cellbatteries.• Supplied butteries are for initial setup. Replace for continued

use.

CAUTION:

Follow these precautions to avoid leaking or cracking cells:• Place batteries in the remote control so they match the polarity:

(+) to (+) and (–) to (–).• Use the correct type of batteries. Batteries that look similar may

differ in voltage.• Always replace both batteries at the same time.• Do not expose batteries to heat or flame.

When using the remote control, aim the remote control directly atthe remote sensor on the front panel.

Remote sensor

01-05RX-F10S[J]_f.p65 04.4.22, 15:254

5

Snap the tabs on the loopinto the slots of the baseto assemble the AM loopantenna.

Connecting the FM and AM antennasDo not connect the AC power plug to the wall outlet until all connections are completed.

AM loop antenna(supplied)

If AM reception is poor, connectan outdoor single vinyl-coveredwire (not supplied).

AM antenna connectionConnect the AM loop antenna supplied to the AM LOOP terminals.Connect the white cord to the AM EXT terminal, and connect theblack cord to the H terminal.Turn the loop until you have the best reception.• If the reception is poor, connect an outdoor single vinyl-covered

wire (not supplied) to the AM EXT terminal. Keep the AM loopantenna connected.

FM antenna connectionConnect the FM antenna supplied to the FM 75 Ω COAXIALterminal as a temporary measure.Extend the supplied FM antenna horizontally.• If the reception is poor, connect an outdoor FM antenna (not

supplied). Before attaching a 75 Ω coaxial cable with aconnector, disconnect the supplied FM antenna.

FM antenna (supplied)

NOTES

• If the AM loop antenna wire is covered with vinyl,remove the vinyl while twisting it as shown on theright.

• Make sure the antenna conductors do not touchany other terminals, connecting cords and powercord. This could cause poor reception.

Get

tin

g s

tart

ed

If FM reception is poor, connect anoutdoor FM antenna (not supplied).

ANTENNA

COAXIAL

AM LOOPFM 75

AM EXT

01-05RX-F10S[J]_f.p65 04.4.23, 13:405

6

Get

tin

g s

tart

ed

Connecting the speakersTurn off all components before making connections.

1 Twist and remove the insulation at the end of eachspeaker cord.

2 Press and hold the clamp of the speaker terminal(1), then insert the speaker cord (2).

• For each speaker, connect the (+) and (–) terminals on therear panel to the (+) and (–) terminals marked on thespeakers.

3 Release the finger from the clamp.

CAUTIONS:

• Use speakers with the SPEAKER IMPEDANCE indicated by thespeaker terminals (6 Ω – 16 Ω).

• DO NOT connect more than one speaker to one speakerterminal.

Connecting the speakersDo not connect the AC power plug to the wall outlet until all connections are completed.

Speaker Layout Diagram

Poweredsubwoofer

(SW)

Surround backspeaker (SB)

Connecting the powered subwooferBy connecting a subwoofer, you can enhance the bass orreproduce the original LFE signals recorded in digital software.

Connect the input jack of a powered subwoofer to theSUBWOOFER OUT jack on the rear panel, using a cordwith RCA pin plugs (not supplied).

• Refer also to the manual supplied with your subwoofer.

After connecting all the speakers and/or a subwoofer, set thespeaker setting information properly to obtain the best possiblesurround effect. For details, see pages 16 to 19.

NOTE

You can place a subwoofer wherever you like since bass sound isnon-directional. Normally place it in front of you.

Right front speaker(R)

Left front speaker(L)

Right surroundspeaker (RS)

Left surroundspeaker (LS)

Center speaker (C)

12

1 2 3

SUBWOOFEROUT

CENTER SURROUND SURROUNDBACK SPEAKERS

LEFTRIGHT LEFTRIGHT

FRONT

CAUTION: SPEAKERIMPEDANCE 6 ~ 16

L R

LS RSSB

C

SW

06-11RX-F10S[J]_f.p65 04.4.22, 15:256

7

Get

tin

g s

tart

ed

Y PB PR

COMPONENT VIDEO

MONITOROUT

DVR/DVDIN

VCRIN

VIDEO

VCROUT(REC)

DVR/DVDIN (PLAY)

DVROUT (REC)

VCROUT(REC)

DVROUT (REC)

DVR/DVDIN (PLAY)

AUDIO

L

R

Å ı

Î ‰ Ï ÌÇ

Turn off all components before making connections.• When you connect other components, refer also to their

manuals.

DO NOT use a TV through a VCR or a TV with a built-inVCR; otherwise, the picture may be distorted.

CAUTION:

If you connect a sound-enhancing device such as a graphicequalizer between the source components and this receiver, thesound output through this receiver may be distorted.

If your video components have AV COMPU LINK terminal

See also page 32 for detailed information about the connectionand the AV COMPU LINK remote control system.

Å To left/right audio channel outputı Only for DVD recorder: To left/right audio channel

inputÇ Only for DVD recorder: To composite video inputÎ To composite video output‰ To S-video outputÏ Only for DVD recorder: To S-video inputÌ To component video output

• Connect Y, PB, and PR correctly.

White

Red

DVD recorder orDVD player

White

Red

Stereo audio cable(not supplied)

Green Blue Red

Component video cable (not supplied)

S-video cable (not supplied)

Composite video cable(not supplied)

7 Connecting a DVD recorder or DVD player with its stereo output jacks:

This receiver is equipped with the following video terminals—composite video, S-video, and component video terminals.• If your video components have S-video (Y/C-separation) and/or

component video (Y, PB, PR) jacks, connect them using an S-video cable (not supplied) or component video cable (notsupplied). By using these terminals, you can get a better picturequality in the order:

Component > S-video > Composite

IMPORTANT:

The video signals from one type of these input jacks aretransmitted only through the video output jacks of the sametype. Therefore, if a recording video component and a playingvideo component are connected to the receiver through the videoterminals of different type, you cannot record the picture. Inaddition, if the TV and a playing video component are connectedto the receiver through the video terminals of different type, youcannot view the playback picture on the TV.

Connecting video componentsDo not connect the AC power plug to the wall outlet until all connections are completed.

NOTE

When connecting a DVD recorder or DVD player to thecomponent video input jacks, make the component video inputsetting (DVD VIDEO) correctly for AV COMPU LINK remotecontrol system. See page 21 for details.

06-11RX-F10S[J]_f.p65 04.4.22, 15:257

8

Get

tin

g s

tart

ed

SURR-LSURR-RCENTERSUBWOOFER

DVD MULTI IN

Y PB PR

COMPONENT VIDEO

MONITOROUT

DVR/DVDIN

VCRIN

VIDEO

VCROUT(REC)

DVR/DVDIN (PLAY)

DVROUT (REC)

VCROUT(REC)

DVROUT (REC)

DVR/DVDIN (PLAY)

AUDIO

L

R

Å ı Ç Î ‰

Ï Ì Ó È Ô

7 Connecting a DVD recorder or DVD player with its analog discrete output jacks (DVD MULTI IN):This connection is the best connection method for enjoying DVD Audio sounds. When a DVD Audio disc is played back, the original high-quality sounds can be reproduced only using this connection.

Turn off all components before making connections.• When you connect other components, refer also to their manuals.


Monaural audio cable(not supplied)

About “DVD MULTI”

When you select “DVD MULTI” as the source (see page 12), you can enjoy analog discrete output sound (5.1-channel reproduction)from the connected component.• You may need to select analog discrete output mode on the component.

NOTES

• When using the headphones, you can listen to the front channel sounds (left and right) only. 3D HEADPHONE mode (see pages 28and 29) is not available.

• When TV Direct is activated while “DVD MULTI” is selected as the source, the source changes to the last selected source—“DVR/DVD,” “VCR,” and “DBS” (see page 14).

• Surround/DSP modes (see pages 27 to 31) are not available for “DVD MULTI.”

White

Red

White

Red

Monaural audio cable(not supplied)


Composite videocable (not supplied)


Å To subwoofer outputı To left/right surround channel audio outputÇ To center channel audio outputÎ To left/right front channel audio output‰ Only for DVD recorder: To left/right front channel

audio inputÏ Only for DVD recorder: To composite video inputÌ To composite video outputÓ To S-video outputÈ Only for DVD recorder: To S-video inputÔ To component video output


Green Blue Red


NOTE

When connecting a DVD recorder or DVD player to thecomponent video input jacks, make the component video inputsetting (DVD VIDEO) correctly for AV COMPU LINK remotecontrol system. See page 21 for details.

White

Red

DVD recorder orDVD player

06-11RX-F10S[J]_f.p65 04.4.22, 15:258

9

Get

tin

g s

tart

ed

Y PB PR

COMPONENT VIDEO

MONITOROUT

DVR/DVDIN

VCRIN DBS

INVCROUT

(REC)IN

(PLAY)DVR/DVDIN (PLAY)

VCR DBSIN

IN(PLAY)

OUT(REC)

DVR/DVDIN (PLAY)

Å ı

Ì

Ç

Î‰ Ï

7 Connecting a VCR


Å To left/right audio channel outputı To left/right audio channel inputÇ To composite video inputÎ To composite video output‰ To S-video outputÏ To S-video inputÌ To component video output


Stereo audio cable(not supplied)White

Red

White




Red

Green Blue Red

VCR

NOTE

When connecting a VCR to the component video input jacks,make the component video input setting (VCR VIDEO) correctlyfor AV COMPU LINK remote control system. See page 21 fordetails.

06-11RX-F10S[J]_f.p65 04.4.22, 15:259

10

Get

tin

g s

tart

ed

TVDBSININ

MONITOROUT

Y PB PR

COMPONENT VIDEO

MONITOROUT

DVR/DVDIN

VCRIN

DBSIN

MONITOROUT

VIDEO

S-VIDEO

Å ı

Ç ‰Î



DBS tuner

Å To left/right audio channel outputı To composite video outputÇ To S-video output

7 Connecting a TVConnect the TV to the appropriate MONITOR OUT jacks to view the playback pucture from any other connected video components.


Red


TV

White

Red


Composite video cable(not supplied)

Green Blue

White

Red


White

Red

Å To left/right audio channel inputı To left/right audio channel outputÇ To composite video inputÎ To S-video input‰ To component video input


IMPORTANT:

Audio signals come out through the MONITOR OUT (L/R) jacksONLY when TV Direct is in use (see page 14).Connect these jacks to the audio input jacks corresponding to thevideo connection; otherwise, no sound comes out of the TVspeaker when TV Direct is in use.

TVVCR DBSININ

IN(PLAY)

DBSIN

VCR MONITOROUT

IN(PLAY)

Å

ı Ç


7 Connecting a DBS tuner

06-11RX-F10S[J]_f.p65 04.4.22, 15:2510

11

Get

tin

g s

tart

ed

DIGITAL IN

2(DBS)3(VCR) 1(DVR/DVD)

NOTES• When shipped from the factory, the DIGITAL IN terminals have

been set for use with the following components:– 1(DVR/DVD): For DVD recorder or DVD player– 2(DBS): For DBS tuner– 3(VCR): For VCRIf you connect other components, change the digital input(DIGITAL IN) terminal setting correctly. See “Setting the digitalinput (DIGITAL IN) terminals—DIGITAL IN1/2/3” on page 21.

• Select the correct digital input mode. See “Selecting the analogor digital input mode” on page 12.

• When you want to operate the connected component (exceptDBS tuner) using the AV COMPU LINK remote control system(see pages 32 and 33), connect them also as described onpages 7 to 10.

Digital connectionThis receiver is equipped with three DIGITAL IN terminals—onedigital coaxial terminal and two digital optical terminals—and oneDIGITAL OUT terminal.To reproduce the digital sound, use the digital connection inaddition to the analog connection methods described on pages 7to 10.

Digital coaxial cable (supplied: 1 cable)

Digital optical cable (not supplied)

Turn off all components before making connections.• When you connect other components, refer also to their

manuals.

7 Digital input terminals

When the component has a digital coaxial outputterminal, connect it to the 1(DVR/DVD) terminal,using a digital coaxial cable (supplied).

When the component has a digital optical outputterminal, connect it to the 2(DBS) or 3(VCR)terminal, using a digital optical cable (not supplied).

Before connecting a digitaloptical cable, unplug theprotective plug.

NOTE

The digital signal format transmitted through the DIGITAL OUTterminal is the same as that of the input signal. For example,when the DTS signals are input, the DTS signals are transmitted.

Connecting the power cordWhen all the audio/video connections have been made, connectthe AC power plug to the wall outlet. Make sure that the plugs areinserted firmly. The standby lamp lights in red.

CAUTIONS:

• Do not touch the power cord with wet hands.• Do not alter, twist or pull the power cord, or put anything heavy

on it, which may cause fire, electric shock, or other accidents.• If the cord is damaged, consult a dealer and have the power

cord replaced with a new one.

NOTES

• Keep the power cord away from the connecting cables and theantenna. The power cord may cause noise or screeninterference.

• The preset settings such as preset channels and soundadjustment may be erased in a few days in the following cases:– When you unplug the power cord.– When a power failure occurs.

7 Digital output terminalYou can connect any digital componens which have an opticaldigital input terminal.

Connecting digital recording equipment to theDIGITAL OUT terminal enables you to performdigital-to-digital recording.

PCM/STREAM

DIGITAL OUT

06-11RX-F10S[J]_f.p65 04.4.22, 15:2511

12

Bas

ic o

per

atio

ns

Basic operations 2 Select the source to playOn the front panel:Turn SOURCE SELECTOR until the source nameyou want appears on the display.The source lamp corresponding to the selected source lights inred.• As you turn SOURCE SELECTOR, the source changes as

follows:

DVD MULTI: Select the DVD player using the analogdiscrete output mode (5.1-channelreproduction).

DVR/DVD (DGT)*: Select the DVD recorder or DVD player.VCR (DIGITAL)*: Select the VCR.DBS (DIGITAL)*: Select the DBS tuner.TV (DIGITAL)*: Select the TV.FM: Select an FM broadcast.AM: Select an AM broadcast.

From the remote control:Press one of the source selecting buttons.• For the tuner, press FM/AM. Each time you press FM/AM, the

band alternates between FM and AM.

* Selecting the analog or digital input modeFor a component you have connected using both the analogconnection and the digital connection methods (see pages 7 to 11),you need to select the correct input mode.• You can select the digital input only for sources which you have

selected digital input terminals for. (See “Setting the digital input(DIGITAL IN) terminals—DIGITAL IN1/2/3” on page 21.)

From the remote control ONLY:Press ANALOG/DIGITAL INPUT to select theanalog or digital input mode.• Each time you press the button, the input mode alternates

between the analog input (“ANALOG”) and the digital input(“DGTL AUTO”). This setting is memorized for each source.

DGTL AUTO: Select for the digital input mode. The receiverautomatically detects the incoming signalformat, then the digital signal format indicator(LPCM, DOLBY D, DTS, or DTS 96/24) forthe detected signal lights up.

ANALOG: Select for the analog input mode.

Initial setting: ANALOG

NOTE

You cannot select the digital input mode when selecting “DVDMULTI,” “FM,” or “AM” as the source.

1 Turn on the powerPress STANDBY/ON (or AUDIO on theremote control).The standby lamp goes off and the source lamp of the currentsource lights in red.

Current source name appears.

To turn off the power (into standby)Press STANDBY/ON (or AUDIO on the remote control)again.The standby lamp lights in red.

NOTE

A small amount of power is consumed in standby mode. To turnthe power off completely, unplug the AC power cord.

When operating the receiverusing the remote control, setthe mode selector to“AUDIO/TV/VCR/DBS.”

EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE


C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST SLEEPAUTO MUTING AUTO MODEATTHPMHzkHz

EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



DVR/DVD (DGT)DVD MULTIVCR (DIGITAL) DBS (DIGITAL)TV (DIGITAL) FM AM(Back to the beginning)

1 2 3

Source lamps

1

3

2

12-15RX-F10S[J]_f.p65 04.4.22, 15:2512

13

Bas

ic o

per

atio

ns

3 Adjust the volumeTo increase the volume, turn MASTER VOLUMEcontrol clockwise (or press VOLUME + on theremote control).

To decrease the volume, turn MASTER VOLUMEcontrol counterclockwise (or press VOLUME – onthe remote control).• When you adjust the volume, the volume level indication

appears on the display for a while.

CAUTION:

Always set the volume to the minimum before starting anysources. If the volume is set at its high level, the sudden blast ofsound energy can permanently damage your hearing and/or ruinyour speakers.

NOTE

The volume level can be adjusted within the range of “0” (minimum)to “50” (maximum).

Listening with headphonesYou can enjoy not only stereo software but also multi-channelsoftware through the headphones. (Sounds are down-mixed to thefront channels while playing multi-channel software.)

Connect a pair of headphones to the PHONES jack on thefront panel to activate the HEADPHONE mode.

The HP (headphone) indicator lights up on the display.• You can also enjoy the Surround/DSP mode through the

headphones—3D HEADPHONE mode. For details, see pages28 and 29.

• Disconnecting a pair of headphones from the PHONES jackcancels the HEADPHONE (or 3D HEADPHONE) mode andactivates the speakers.

CAUTION:

Be sure to turn down the volume:• Before connecting or putting on headphones, as high volume

can damage both the headphones and your hearing.• Before removing headphones, as high volume may output from

the speakers.

Selecting the digital decode modeIf the following symptoms occur while playing Dolby Digital or DTSsoftware with “DGTL AUTO” selected (see page 12), follow theprocedure below:• Sound does not come out at the beginning of playback.• Noise comes out while searching for or skipping chapters or

tracks.

From the remote control ONLY:

Press SOUND, then press DECODE to select“DGTL D.D.” or “DGTL DTS.”• Each time you press DECODE, the digital decode mode

changes as follows:

• To play back software encoded with Dolby Digital, select“DGTL D.D.”

• To play back software encoded with DTS, select “DGTL DTS.”

NOTES

• When you turn off the power or select another source,“DGTL D.D.” or “DGTL DTS” is canceled and the digital decodemode is automatically reset to “DGTL AUTO.”

• After pressing SOUND, the numeric buttons work for soundadjustments. To use the numeric buttons to operate your targetsource, press the corresponding source selecting button beforeoperation; otherwise, the remote control may not work as youintend.

The following digital signal format indicators on the displayindicate what type of signal comes into the receiver.

LPCM: Lights up when Linear PCM signal comes in.

DOLBY D: • Lights up when Dolby Digital signal comes in.• Flashes when “DGTL D.D.” is selected for any

software other than Dolby Digital.

DTS: • Lights up when conventional DTS signal comesin.

• Flashes when “DGTL DTS” is selected for anysoftware other than DTS.

DTS 96/24: Lights up when DTS 96/24 signal comes in.

NOTE

When “DGTL AUTO” cannot recognize the incoming signal, nodigital signal format indicator lights up on the display.

EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



DGTL AUTO DGTL D.D.DGTL DTS (Back to the beginning)

12-15RX-F10S[J]_f.p65 04.4.22, 15:2513

14

Bas

ic o

per

atio

ns

Adjusting the subwoofer audiopositionIf the subwoofer sound is much reinforced for stereo soundcompared to the sound reproduced with multi-channel, set thesubwoofer audio position. The subwoofer output level isautomatically decreased by the selected value when you arelistening in stereo.The AUDIO P. indicator lights up when this function is activated.• Once you have made an adjustment, it is memorized for each

source.


Press SOUND, then press A.POSITION repeatedly.• Each time you press A.POSITION, the subwoofer audio position

level changes as follows:

AUDIO P. indicator

The smaller the number becomes, the more the level decreasesautomatically when listening in stereo.• If no adjustment is required, select “OFF” (initial setting).

NOTES

• The minimum subwoofer output level is –10 dB.Ex.: When setting the subwoofer output level to “–8 (dB)” and

the subwoofer audio position to “–4 (dB),” the subwooferoutput level when listening in stereo will be –10 dB.

To adjust the subwoofer output level, see page 23.• This function is not available when the Surround/DSP mode is

activated or “DVD MULTI” is selected.• After pressing SOUND, the numeric buttons work for sound

adjustments. To use the numeric buttons to operate your targetsource, press the corresponding source selecting button beforeoperation; otherwise, the remote control may not work as youintend.

Activating TV DirectTV Direct enables you to use this receiver as an AV selectorwhile the receiver is turned off.When TV Direct is activated, the pictures and sounds go from thevideo components such as DVD player to the TV through thisreceiver. Thus, you can use the video components and the TV asif they were connected directly.• This function takes effect for the following sources—DVR/DVD,

VCR, and DBS.

To activate (or deactivate) TV Direct, follow the procedure below:

1 Press TV DIRECT.All the indications disappear, then the source lamp of thecurrent source lights in green.

2 Turn on the video component and TV.

3 Select the target video component.

On the front panel:Turn SOURCE SELECTOR until one of thesource lamps—DVR/DVD, VCR, or DBS—lightsin green.

From the remote control:Press one of the source selecting buttons—DVR/DVD, VCR, or DBS.The source lamp corresponding to the selected source lightsin green.

To cancel TV Direct and turn off the receiver, press STANDBY/ON on the front panel (or AUDIO on the remote

control).The receiver is turned off and the standby lamp lights up.

To cancel TV Direct and turn on the receiver, press TV DIRECTagain.The receiver is turned on and the source lamp currently selectedlights in red.

NOTES

• When TV Direct is activated, you cannot enjoy any of the soundeffects the receiver produces, and cannot use the speakersconnected to the receiver.

• When TV Direct is activated while “DVD MULTI,” “FM,” or “AM” isselected as the source, the source changes to the last selectedsource—“DVR/DVD,” “VCR,” or “DBS.”


EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



–2 –4 –6OFF (canceled)

12-15RX-F10S[J]_f.p65 04.4.22, 15:2514

15

Bas

ic o

per

atio

ns

Turning off the sounds temporarily

From the remote control ONLY:Press MUTING to turn off the sound through allconnected speakers and headphones.“MUTING” appears on the display and the volume turns off.

To restore the sound, press MUTING again.

• Pressing VOLUME +/– (or turning MASTER VOLUME controlon the front panel) also restores the sound.

Changing the display brightnessYou can dim the display—Dimmer.

From the remote control ONLY:Press DIMMER repeatedly.• Each time you press the button, the display brightness changes

as follows:

DIMMER 1: Dims the display slightly.Dims the blue illumination slightly.

DIMMER 2: Dims the display more than DIMMER 1.Dims the blue illumination slightly (same asDIMMER 1).

DIMMER 3: Turns off the display and blue illumination.(Temporarily canceled when you operate thereceiver.*)

DIMMER OFF: Cancels the Dimmer (normal display).

* Except when activating or deactivating TV Direct.

Turning off the power with the SleepTimerYou can fall asleep while listening to music—Sleep Timer.

From the remote control ONLY:Press SLEEP repeatedly.• Each time you press the button, the shut-off time changes in 10

minute intervals. The SLEEP indicator lights up on the display.

SLEEP indicator

When the shut-off time comes:The receiver turns off automatically.

To check or change the remaining time until the shut-offtime:Press SLEEP once.The remaining time (in minutes) until the shut-off time appears.• To change the shut-off time, press SLEEP repeatedly.

To cancel the Sleep Timer:Press SLEEP repeatedly so that “SLEEP OFF” appears on thedisplay. (The SLEEP indicator goes off.)• The Sleep Timer is also canceled when:

– You turn off the receiver, or– You activate TV Direct.

Basic adjustment of auto memoryThis receiver memorizes sound settings for each source:• when you turn off the power, and• when you change the source.

When you change the source, the memorized settings for thenewly selected source are automatically recalled.The following can be stored for each source:• Analog/digital input mode (see page 12)• Subwoofer audio position (see page 14)• Speaker output level (see page 23)• Subwoofer phase (see page 24)• Digital equalization pattern (see page 24)• Bass boost (see page 24)• Input attenuator mode (see page 24)• Surround/DSP mode selection (see pages 30 and 31)

NOTE

If the source is FM or AM, you can assign a different settingfor each band.

Signal and speaker indicators on the display

Signal indicators Speaker indicators

The signal indicators light up as follows:

L: • When digital input is selected: Lights up when theleft channel signal comes in.

• When analog input is selected: Always lights up.R: • When digital input is selected: Lights up when the

right channel signal comes in.• When analog input is selected: Always lights up.

C: Lights up when the center channel signal comes in.LS*: Lights up when the left surround channel signal comes

in.RS*: Lights up when the right surround channel signal comes

in.SB: Lights up when the surround back channel signal

comes in.LFE: Lights up when the LFE channel signal comes in.

* When monaural surround signal comes in, only “S” lights up.

NOTE

When “DVD MULTI” is selected as the source, all the signalindicators except “SB” light up.

The speaker indicators light up as follows:

• The subwoofer indicator (S . WFR) lights up when“SUBWOOFER” is set to “SUBWFR :YES.” For details, seepage 18.

• The other speaker indicators light up only when thecorresponding speaker is set to “SML (small)” or “LRG(large),” and also when required for the current playback.

EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



10 20 30 40 50 60

90OFF (canceled) 80 70

EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE


C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS

L

LS SB RS

S . WFR LFE

C RL

LS SB RS

S . WFR LFE

C R

12-15RX-F10S[J]_f.p65 04.4.22, 15:2515

16

Bas

ic s

etti

ng

s

To obtain the best possible sound effect from Surround/DSPmodes (see pages 27 to 31), you need to set up the speaker andsubwoofer information after all the connections are completed.From pages 16 to 21, how to set speakers and other basic itemsof the receiver are explained.

Setting the speaker informationautomatically—Smart Surround SetupThe distance from your listening point to the speakers is one ofthe important elements to obtain the best possible sound effect forthe Surround/DSP modes.By using Smart Surround Setup, the following are automaticallycalculated by one simple action—clapping hands.• Speaker distance (compared to that of the closest speaker)• Speaker output level (except the subwoofer)

NOTES

• To set the speaker information effectively using Smart SurroundSetup, unplug the power cords of all the components connectedto this receiver and the subwoofer which may cause noise.

• Before starting Smart Surround Setup, set the speakerinformation correctly (SML, LRG, or NO) according to yourspeakers except the subwoofer (see page 18).

• When the setting is made by Smart Surround Setup, thespeaker distance and output level you have set before will beinactive.

• If you have turned off the display, cancel the Dimmer (see page15); otherwise, you cannot see the information on the displayduring Smart Surround Setup.

• Smart Surround Setup will not be done correctly if you or otherobject blocks the sound.

• When you change your speakers, do the following procedureagain.


2 Press and hold SMART SURROUND SETUPuntil “SETTING UP” flashes on the display.

3 Confirm that “SETTING UP” stops flashing,then clap your hands over your head oncewhile “SETTING UP” still remains on thedisplay.The receiver starts detecting the level of the sound comingthrough each speakers (except the subwoofer).

When your clapping sound is detected successfully,

“SUCCESSFUL” appears on the display, then the values set areshown as follows:Ex.:

Then the receiver returns tonormal operation mode.

*1 Standard channel (the closest speaker).This speaker position now works as the referenceposition (“0m/ft”) and other speakers’ distance isshown by the difference with this reference speakerposition.

*2 L: Left front speakerR: Right front speakerC: Center speakerLS: Left surround speakerRS: Right surround speakerSB: Surround back speaker

*3 Difference of each speaker position in distance (inmeters or feet).

*4 Each speaker’s output level (–6 to +6).

When your clapping sound is not detected correctly,

“SETTING UP” appears again after one of the followingmessages. In this case, repeat step 3.

SILENT: • The receiver detects sound from only the leftand right front speakers.

• The receiver detects no sound from the frontspeakers and detects sound from at least one ofthe other speakers.

SILENT-ALL: The receiver cannot detect any sound from anyspeakers for about 15 seconds.

FAILED: The receiver cannot detect sound from the left orright front speaker.

1 Take your position where you listen to thesound.• Make sure speaker cables are connected firmly.

Basic settings


EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



*3*2*1 *4

L RLS RS SB

C

16-21RX-F10S[J]_f.p65 04.4.22, 15:2516

17

Bas

ic s

etti

ng

s

In the following cases, set the speakers manually.

• When the receiver detects the sound but as “SILENT” twicein succession.

The setting is made. (The distance of the speakers from whichsound has not been detected is set to “+9.0m (+30ft).”)The receiver exits from Smart Surround Setup.

• When the receiver fails to detect the sound three times.

“MANUAL” appears on the display. The receiver exits fromSmart Surround Setup.

To cancel Smart Surround Setup, press SMART SURROUNDSETUP while “SETTING UP” flashes on the display.• No other operations can be accepted after “SETTING UP” stops

flashing. Complete the Smart Surround Setup.

To check the setting made by Smart Surround Setup, pressSMART SURROUND SETUP while the receiver is in normaloperation mode.The setting values appear one after another (see page 16).• If you have changed speaker distance and/or output level

manually after using Smart Surround Setup, “MANUAL”appears.

• If you have not used Smart Surround Setup, “NO S.S.S.”appears.

NOTES

• The speaker distance and output level manually set will beapplied instead of those set by using Smart Surround Setup inthe following cases:– When you change one of the speaker distance (see page 19).– When you change one of the speaker output level (see page

23).– When you change one of the speaker size either from “NO” to

“SML” or “LRG,” or from “SML” or ”LRG” to “NO” (see page 18).• When you want to adjust the speaker distance and output level

manually, see pages 19 and 23.• Do not clap your hands so hard that it may hurt your hands.

Basic setting itemsYou can adjust the following items. See pages in parentheses fordetails.• You cannot select the items which is not available with the

current setting.

Items To do

SUBWOOFER Register your subwoofer. (18)

FRONT SPK Register your front speaker size. (18)

CENTER SPK Register your center speaker size. (18)

SURRND SPK Register your surround speaker size. (18)

S BACK SPK Register your surround back speaker size.(18)

DIST UNIT Select the measuring unit for the speakerdistance. (19)

FRNT L DIST* Register the distance from the left frontspeaker to your listening point. (19)

FRNT R DIST* Register the distance from the right frontspeaker to your listening point. (19)

CENTER DIST* Register the distance from the center speakerto your listening point. (19)

SURR L DIST* Register the distance from the left surroundspeaker to your listening point. (19)

SURR R DIST* Register the distance from the right surroundspeaker to your listening point. (19)

S BACK DIST* Register the distance from the surround backspeaker to your listening point. (19)

SUBWFR OUT Select sounds emitted from the subwoofer.(19)

EX/ES Select the EX/ES reproduction mode. (20)

DUAL MONO Select the Dual Mono sound channel. (20)

CROSS OVER Select the cutoff frequency to the subwoofer.(19)

LFE ATT Attenuate the bass (LFE) sounds. (19)

MIDNIGHT M. Reproduce a powerful sound at night. (20)

DIGITAL IN1 Select the component connected to the digitalcoaxial terminal—1(DVR/DVD). (21)

DIGITAL IN2 Select the component connected to the digitaloptical terminal—2(DBS). (21)

DIGITAL IN3 Select the component connected to the digitaloptical terminal—3(VCR). (21)

AUTO SURRND Select Auto Surround mode. (21)

DVD VIDEO Select the type of video terminal used for theDVD recorder or DVD player. (21)

VCR VIDEO Select the type of video terminal used for theVCR. (21)

* If you have used Smart Surround Setup on page 16, thesesettings are not required.

CONTINUED ON THE NEXT PAGE

16-21RX-F10S[J]_f.p65 04.4.22, 15:2517

18

Bas

ic s

etti

ng

sOperating procedure

On the front panel ONLY:

Before you start, remember...

There is a time limit in doing the following steps. If the setting iscanceled before you finish, start from step 1 again.

Ex.: When setting DIGITAL IN 1 terminal.

1 Press SETTING.MULTI JOG now works for the setting operation.

2 Turn MULTI JOG until the item you want to setappears on the display.• As you turn MULTI JOG, the setting items change as

follows:

3 Press SET.The current setting of the selected item appears.

4 Turn MULTI JOG to select the appropriatesetting.

Your setting is stored.

5 Press SET.

6 Repeat steps 2 to 5 to set other items ifnecessary.

Setting the speakersSetting subwoofer information—SUBWOOFEREach time the receiver turns on, the receiver detects thesubwoofer connection and automatically changes the setting ofthe subwoofer.When you want to change the setting manually, select either onebelow.

SUBWFR :YES Select when you have connected a subwoofer.The subwoofer indicator (S . WFR) lights up on thedisplay. You can adjust the subwoofer output level(see page 23).

SUBWFR : NO Select when you have disconnected a subwoofer.Selecting this changes the front speaker size to“LRG” (see below).

NOTE

You need to change the setting each time you turn on the receiverif you want to change the subwoofer information set automatically.

Setting the speaker size—FRONT SPK (frontspeakers), CENTER SPK (center speaker), SURRNDSPK (surround speakers), S BACK SPK (surroundback speaker)Register the sizes of all the connected speakers.

LRG (large) Select when the cone speaker size is larger than12 cm (4 3/4 inches).

SML (small) Select when the cone speaker size is smaller than12 cm (4 3/4 inches).

NO Select when you have disconnected a speaker.(Not selectable for the front speakers.)

Initial setting: SML for all speakers*

* When “SUBWOOFER” is set to “SUBWFR : NO,” the frontspeaker size is fixed to “LRG” (and you cannot select “SML”).

NOTES

• If you have selected “SML (small)” for the front speaker size,you cannot select “LRG (large)” for other speakers.

• When “SURRND SPK” is set to “SML (small),” you cannot select“LRG (large)” for the surround back speaker.

• When “SURRND SPK” is set to “NO,” the surround backspeaker is fixed to “NO.”

• If you change one of the speaker size either from “NO” to “SML”or “LRG,” or from “SML” or “LRG” to “NO,” the distance andoutput level manually set will be applied instead of those set byusing Smart Surround Setup.

1 2, 43, 5

EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



CENTER SPK SURRND SPK

FRNT R DISTCENTER DIST

(Back to the beginning)

S BACK SPK

SUBWOOFER FRONT SPK

DIST UNITFRNT L DIST

SURR L DISTS BACK DISTSURR R DIST

DUAL MONO CROSS OVERSUBWFR OUT EX/ES

LFE ATT MIDNIGHT M.

DIGITAL IN3 AUTO SURRNDDVD VIDEO VCR VIDEO

DIGITAL IN1 DIGITAL IN2

EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



DVR/DVD DBSVCRTV

16-21RX-F10S[J]_f.p65 04.4.22, 15:2518

19

Bas

ic s

etti

ng

s

Setting the speaker distanceThe distance from your listening point to the speakers is one ofthe important elements to obtain the best possible sound effectfrom the Surround/DSP modes.By referring to the speaker distance, the receiver automaticallysets the delay time of the sound through each speaker so thatsounds through all the speakers can reach you at the same time.

7 Measuring unit—DIST UNIT

Select which measuring unit you use.

UNIT :meter Select to set the distance in meters.

UNIT : feet Select to set the distance in feet.

Initial setting: UNIT :meter

7 Speaker distance—FRNT L DIST (for the left front speaker),FRNT R DIST (for the right front speaker),CENTER DIST (for the center speaker),SURR L DIST (for the left surround speaker),SURR R DIST (for the right surround speaker),S BACK DIST (for the surround back speaker)

Adjustable range: 0.3 m to 9.0 m in 0.3 m intervals(1 ft to 30 ft in 1 ft intervals)

Initial setting: 3.0 m (10 ft) for all speakers

• If you have used Smart Surround Setup on page 16, thissetting is not required.

Setting bass soundSetting subwoofer output—SUBWFR OUTYou can select the type of the signal which can be transmittedthrough the subwoofer. In other words, you can determinewhether or not the bass elements of the front speaker channelsare transmitted through the subwoofer regardless of the frontspeaker size setting (either “SML” or “LRG”).

SW: LFE Select to emit only the LFE signals (whileplaying Dolby Digital and DTS software) orthe bass elements of the “SML (small)” frontspeakers (while playing any source other thanabove).

SW:LFE+MAIN Select to always emit the bass elements ofthe front speaker channels (MAIN). Whileplaying Dolby Digital and DTS software, thebass elements and the LFE signals are bothemitted.

Initial setting: SW: LFE

NOTE

When “SUBWOOFER” is set to “SUBWFR : NO” (see page 18),this function is not available.

Setting the crossover frequency—CROSS OVERSmall speakers cannot reproduce the bass sounds efficiently. Ifyou use a small speaker in any position, this receiverautomatically reallocates the bass sound elements assigned tothe small speaker to the large speakers.To use this function properly, set this crossover frequency levelaccording to the size of the small speaker connected.• If you have selected “LRG (large)” for all speakers (see page

18), this function will not take effect (“CROSS: OFF” appears).

CROSS: 80Hz Select when the cone speaker unit built in thespeaker is about 12 cm (4 3/4 inches).

CROSS:100Hz Select when the cone speaker unit built in thespeaker is about 10 cm (3 15/16 inches).



CROSS:200Hz Select when the cone speaker unit built in thespeaker is less than 5 cm (2 inches).

Initial setting: CROSS:150Hz

NOTE

Crossover frequency is not valid for the HEADPHONE and 3DHEADPHONE modes.

Setting the low frequency effect attenuator—LFEATTIf the bass sound is distorted while playing back softwareencoded with Dolby Digital or DTS, set the LFE level to eliminatedistortion.• This function takes effect only when the LFE signals come in.

LFE : 0dB Normally select this.

LFE :–10dB Select when the bass sound is distorted.

Initial setting: LFE : 0dB

In this case, set the distance as follows:Left front speaker (L): “FL D : 3.0m (10ft)”Right front speaker (R): “FR D : 3.0m (10ft)”Center speaker (C): “C D : 3.0m (10ft)”Left surround speaker (LS): “LS D : 2.7m (9ft)”Right surround speaker (RS): “RS D : 2.7m (9ft)”Surround back speaker (SB): “SB D : 2.4m (8ft)”

NOTES

• You cannot set the speaker distance for the speakers you haveset to “NO.”

• If you change one of these settings manually, the distance andoutput level manually set will be applied instead of those set byusing Smart Surround Setup.

CL R

SB

LS RS

2.1 m(7 ft)

2.4 m(8 ft)

2.7 m(9 ft)

3.0 m(10 ft)

3.3 m(11 ft)

16-21RX-F10S[J]_f.p65 04.4.22, 15:2519

20

Bas

ic s

etti

ng

sActivating the EX/ES setting—EX/ESDepending on this setting, available Surround modes for digitalmulti-channel software vary—EX/ES (6.1-channel) reproductionor 5.1-channel reproduction. Select an appropriate setting for yourenjoyment.• For details about relation between EX/ES setting and available

Surround mode, see page 30.• To activate the Surround mode, see page 31.

EX/ES :AUTO According to the incoming signal, an appropriateSurround mode is applied.• For Dolby Digital EX and DTS-ES software,

EX/ES (6.1-channel) reproduction is applied*.• For other multi-channel (5.1-channel or less)

encoded software, 5.1-channel reproduction isapplied.

EX/ES : ON Select to apply EX/ES (6.1-channel)reproduction to both 5.1-channel and 6.1-channel encoded software.

EX/ES : OFF Select to cancel the EX/ES (6.1-channel)reproduction.

Initial setting: EX/ES :AUTO

* For some Dolby Digital EX software, Dolby Digital 5.1-channelreproduction (“DOLBY D”) may be applied even though youhave selected 6.1-channel reproduction to apply.

From the remote control:

Set the mode selector to “AUDIO/TV/VCR/DBS.”

Press EX/ES repeatedly to selecteither one of the above.

Selecting the main or sub channel—DUAL MONOYou can select the playback sound (channel) you want whileplaying digital software recorded (or broadcasted) in Dual Monomode (see page 28), which includes two monaural channelsseparately.

D MONO:MAIN Select to play back the main channel (Ch 1).*Signal indicator “L” lights up while playingback this channel.

D MONO: SUB Select to play back the sub-channel (Ch 2).*Signal indicator “R” lights up while playingback this channel.

D MONO: ALL Select to play back both the main and sub-channels (Ch 1/Ch 2).*Signal indicators “L” and “R” light up whileplaying back these channels.

Initial setting: D MONO:MAIN

* Dual Mono signals can be heard from the following speakers—L(left front speaker), R (right front speaker), and C (centerspeaker), with respect to the current Surround setting:

NOTE

The Dual Mono format is not identical with bilingual broadcastingfor TV programs. So this setting does not take effect whilewatching such bilingual programs.

Using the Midnight mode—MIDNIGHT M.You can enjoy a powerful sound at night using the Midnight mode.

NIGHT :OFF Select when you want to enjoy surround with itsfull dynamic range. (No effect applied.)

NIGHT : 1 Select when you want to reduce the dynamicrange a little.

NIGHT : 2 Select when you want to apply the compressioneffect fully (useful at night).

Initial setting: NIGHT :OFF



Press SOUND, then press MIDNIGHTrepeatedly to select either one of theabove.

NOTE

After pressing SOUND, the numericbuttons work for sound adjustments. Touse the numeric buttons to operate yourtarget source, press the correspondingsource selecting button before operation;otherwise, the remote control may notwork as you intend.

NOTES

• When “SURRND SPK” is set to “NO” (see page 18), thisfunction is not available.

• When “S BACK SPK” is set to “NO” (see page 18), the VirtualSurround Back (see page 30) is applied for EX/ES (6.1-channel)reproduction.

Dual Mono setting

Ch 1

Ch 1

Ch 1

Ch 2

Ch 1 Ch 1

SUB Ch 2 Ch 2 Ch 2 Ch 2 Ch 2

Ch1

Ch 1+Ch 2Ch 1+Ch 2Ch 1+Ch 2

L R L RC L R

MAIN

ALL

Without Surround

With Surround Activated

Center speaker setting

SML/LRG NO

16-21RX-F10S[J]_f.p65 04.4.22, 15:2520

21

Bas

ic s

etti

ng

s

Setting the digital input (DIGITAL IN)terminals—DIGITAL IN1/2/3When you use the digital input terminals, register whatcomponents are connected to which terminals—DIGITAL IN1/2/3(see page 11) so that the correct source name will appear whenyou select the digital source.Select one of the following components for each terminal:

DVR/DVD For the DVD player (or DVD recorder).

DBS For the DBS tuner.

VCR For the VCR.

TV For the TV.

Initial setting: DVR/DVD (for “DIGITAL IN1”)DBS (for “DIGITAL IN2”)VCR (for “DIGITAL IN3”)

NOTES

• You cannot assign the same component for different terminals.The priority order for assignment is as follows:

“DIGITAL IN1” > “DIGITAL IN2” > “DIGITAL IN3.”

Ex.: When “DIGITAL IN1” is set to “DVR/DVD.”

For “DIGITAL IN2,” “DBS,” “VCR,” and “TV” are selectable.• In this case, “VCR” is selected.

For “DIGITAL IN3,” “DBS” and “TV” are selectable.

: Selectable : Not selectable

• Setting “DIGITAL IN1” affects “DIGITAL IN2” and “DIGITAL IN3”settings. When you have changed “DIGITAL IN1,” confirm thecomponents assigned to “DIGITAL IN2” and “DIGITAL IN3.”

Setting Auto Surround—AUTO SURRNDYou can enjoy the Surround mode simply by selecting the source(with digital input selected for that source).• Auto Surround also works when the input mode changes from

analog to digital.• For details about the Surround/DSP modes, see pages 27 to 29.Select “AUTO SR: ON” when activating Auto Surround.

AUTO SR: ONThe AUTO SR indicator lights up on the display.• If a multi-channel signal comes in, an appropriate

Surround mode will be turned on.• If a Dolby Digital 2-channel or DTS 2-channel signal

with surround signal comes in, “PLII MOVIE” or“NEO:6CINEMA” will be selected.

• If a Dolby Digital 2-channel or DTS 2-channel signalwithout surround signal comes in, “SURRND OFF(stereo)” will be selected.

• If a Linear PCM signal comes in, nothing willchange.

AUTO SR:OFFSelect to deactivate Auto Surround.

Initial setting: AUTO SR:OFF

NOTES

• This function does not take effect in the following cases:– While playing an analog source,– While selecting any of DSP modes (see page 29), or one of

the fixed digital decode mode—“DGTL D.D.” or “DGTL DTS”(see page 13), and

– While listening with the headphones.• If you press SURROUND with Auto Surround activated, Auto

Surround will be canceled temporarily for the currently selectedsource.Auto Surround setting will be restored in the following cases:– When you turn the receiver off and on,– When you change the source,– When you change the analog/digital input, and– When you select “AUTO SR: ON” again.

Selecting the component video inputmode—DVD VIDEO/VCR VIDEOWhen you use the component video inputs for connecting theDVD recorder (or DVD player) or VCR, register the type of videoinput jacks.If you have not selected appropriate video input jacks, the AVCOMPU LINK remote control system cannot operate properly(see page 32).

For the DVD recorder or DVD player (DVD VIDEO):

DVD : S/C Select when connecting the DVD recorder (orDVD player) to the composite video or S-videoinput jacks.

DVD :COMPNT Select when connecting the DVD recorder (orDVD player) to the component video inputjacks.

Initial setting: DVD : S/C

For the VCR (VCR VIDEO):

VCR : S/C Select when connecting the VCR to thecomposite video or S-video input jacks.

VCR :COMPNT Select when connecting the VCR to thecomponent video input jacks.

Initial setting: VCR : S/C

DVR/DVDDIGITAL IN1 DBS VCR TV

DIGITAL IN2 DVR/DVD DBS VCR TV

DIGITAL IN3 DVR/DVD DBS VCR TV

16-21RX-F10S[J]_f.p65 04.4.22, 15:2521

22

So

un

d a

dju

stm

ents

Sound adjustments

You can make sound adjustment to your preference aftercompleting basic setting.

Basic adjustment itemsYou can adjust the following items. See pages in parentheses fordetails.• You cannot select the items which is not available with the

current setting.

Items To do

SUBWFR LVL Adjust the subwoofer output level. (23)

FRONT L LVL* Adjust the left front speaker output level.(23)

FRONT R LVL* Adjust the right front speaker output level.(23)

CENTER LVL* Adjust the center speaker output level. (23)

SURR L LVL* Adjust the left surround speaker output level.(23)

SURR R LVL* Adjust the right surround speaker outputlevel. (23)

S BACK LVL* Adjust the surround back speaker outputlevel. (23)

EFFECT Adjust the effect level. (23)

PANORAMA Add “wraparound” sound effect with side-wall image. (23)

BASS BOOST Boost the bass level. (24)

INPUT ATT Attenuate the input level of analog source.(24)

CENTER TONE Make the center tone soft or sharp. (23)

D EQ 63Hz Adjust the equalization pattern of eachD EQ 250Hz band. (24)D EQ 1kHzD EQ 4kHzD EQ 16kHz

CENTER GAIN Adjust the sound localization of the centerchannel. (24)

SBWFR PHASE Select the subwoofer sound phase. (24)

* If you have used Smart Surround Setup on page 16, thesesettings are not required.

You can also use the remote control for sound adjustmentexcept for the following items:“PANORAMA,” “INPUT ATT,” “CENTER GAIN,” and “SBWFRPHASE.”

Operating procedure

On the front panel:



Ex.: When adjusting subwoofer output level.

1 Press ADJUST.MULTI JOG now works for the sound adjustment.

2 Turn MULTI JOG until the item you want toadjust appears on the display.• As you turn MULTI JOG, the adjustment items change as

follows:

3 Press SET.The current setting for the selected item appears.

4 Turn MULTI JOG to adjust the selected item.

Your adjustment is stored.

5 Press SET.

6 Repeat steps 2 to 5 to adjust other items ifnecessary.

1 2, 43, 5

EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



SUBWFR LVL FRONT L LVL

SURR L LVLS BACK LVL

SURR R LVL

(Back to the beginning)

FRONT R LVL CENTER LVL

PANORAMAEFFECT

CENTER TONE

SBWFR PHASE

D EQ 63Hz

BASS BOOSTINPUT ATT

D EQ 250HzD EQ 1kHz

CENTER GAIND EQ 4kHz

D EQ 16kHz

EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



–10 0 +10

22-24RX-F10S[J]_f.p65 04.4.22, 15:2522

23

So

un

d a

dju

stm

ents

Adjusting speaker output level• SUBWFR LVL (subwoofer output level),• FRONT L LVL (left front speaker output level),• FRONT R LVL (right front speaker output level),• CENTER LVL (center speaker output level),• SURR L LVL (left surround speaker output level),• SURR R LVL (right surround speaker output level),• S BACK LVL (surround back speaker output level)

You can adjust the speaker output levels.Adjust all the speakers’ output levels so that you can listen to thesounds from all the speakers at the same level.• Once you have made an adjustment, it is memorized for each

source.

Adjustable range: –10 (dB) to +10 (dB) (in 1 step intervals)

Initial setting: 0 (dB) for all speakers

NOTES

• If you have selected “NO” for a speaker (see page 18), theoutput level for the corresponding speaker is not adjustable.

• While using the headphones, you can adjust only the left andright front speakers’ output level.

• If you change one of these settings (except the subwooferoutput level) manually, the distance and output level setmanually will be applied instead of those set by using SmartSurround Setup.



1 Press TEST TONE to check thespeakers’ output balance.

“TEST L” starts flashing on thedisplay, and a test tone comes out ofthe speakers in the following order:

2 Adjust the speaker output levels.

• If no adjustment is made for about one minute, the testtone will stop.

To adjust the left front speaker level (L), pressFRONT L +/–.

To adjust the right front speaker level (R), pressFRONT R +/–.

To adjust the center speaker level (C), pressCENTER +/–.

To adjust the left surround speaker level (LS), pressSURR L +/–.

To adjust the right surround speaker level (RS), pressSURR R +/–.

To adjust the surround back speaker level (SB), pressS.BACK +/–.

To adjust the subwoofer level (SW), press SUBWFR +/–.

3 Press TEST TONE again to stop the test tone.

NOTES

• You can adjust the speaker output levels without the test tone.• No test tone comes out of the speakers for which the speaker

setting is set to “NO” (see page 18).• No test tone is available when the headphone is in use or

“DVD MULTI” is selected.

Adjusting the sound parameters forthe Surround/DSP modesYou can adjust the Surround/DSP sound parameters to yourpreference.• For details about the Surround/DSP modes, see pages 27 to 31.

Adjusting the effect level for DSP modes—EFFECTThis setting is available only when one of the DSP modes (exceptALL CH ST.) is in use. To activate DSP mode, see page 31.• Once you have made an adjustment, it is memorized for each

DSP mode.

Adjustable range: 1 to 5 (in 1 step intervals)

Initial setting: EFFECT 3

As the number increases, the effect becomes stronger.Normally, select “3.”

Adjusting the panorama control for Pro Logic IIMusic—PANORAMAThis setting is available only when Pro Logic II Music is in use. Toactivate Pro Logic II Music, see page 31.• Once you have made an adjustment, it is memorized until you

change the setting.• You cannot use the remote control for this setting.

PANORAMA ON Select to add “wraparound” sound effect withside-wall image.

PANORAMAOFF Select to listen to originally recorded sound.

Initial setting: PANORAMAOFF

Adjusting the center tone—CENTER TONEThis setting is available when one of the Surround/DSP modes isin use.• If you have set “CENTER SPK” to “NO” (see page 18), the

center tone is not adjustable.• This setting is common to all Surround modes, and is

memorized separately for DSP modes.

Adjustable range: 1 to 5 (in 1 step intervals)

Initial setting: CNT TONE 3

As the number increases, the dialogue becomes stronger.Normally, select “3.”• When the center tone is set to other than “CNT TONE 3,” the

C.TONE indicator lights up on the display.

CL

SW

R

SB

LS RS



To adjust the effect level:

Press SOUND, then press EFFECTrepeatedly.

To adjust the center tone:

Press SOUND, then press C.TONErepeatedly.

NOTE


21, 3

22-24RX-F10S[J]_f.p65 04.4.22, 15:2523

24

So

un

d a

dju

stm

ents

Selecting the subwoofer sound phase—SBWFRPHASEYou can change the subwoofer sound phase to your preference.• Once you have made an adjustment, it is memorized for each

source.• You cannot use the remote control for this setting.

PHASE NORM. Normally select this.

PHASE REV. Select this when you feel the bass sound isbetter with this mode rather than with “PHASENORM.”

Initial setting: PHASE NORM.

NOTE

This function takes effect only when “SUBWOOFER” is set to“SUBWFR :YES” (see page 18).

Adjusting the equalization patterns—D EQ 63Hz/250Hz/1kHz/4kHz/16kHzYou can adjust equalization patterns in five frequency bands(center frequency: 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz) for thefront speakers.• Once you have made an adjustment, it is memorized for each

source.

Adjustable range: –8 (dB) to +8 (dB) (in 2 dB intervals)

Initial setting: 0 (dB) for all bands

• When adjustment is made, the EQ indicator lights up on thedisplay.

If no adjustment is required, set all the frequency bands to“0 (dB).”• The EQ indicator goes off from the display.





1 Press SOUND.

2 Press EQ FREQ repeatedly to selectthe band you want to adjust.

3 Press EQ LEVEL +/– to adjust theequalization pattern of the selectedband.

4 Repeat steps 2 and 3 to adjustother bands.

NOTE


Adjusting the sound localization of the centerchannel—CENTER GAINThis setting is available only when Neo:6 Music is in use.• If you have set “CENTER SPK” to “NO” (see page 18), the

center gain is not adjustable.• Once you have made an adjustment, it is memorized until you

change the setting.• You cannot use the remote control for this setting.

Adjustable range: 0 to 0.5 (in 0.1 step intervals)

Initial setting: C GAIN 0.2

As the number increases, the center channel will be localizedclearly.Normally, select “0.2.”

Adjusting the bass soundsReinforcing the bass—BASS BOOSTYou can boost the bass level—Bass Boost.• Once you have made an adjustment, it is memorized for each

source.

B.BOOST ON Select to boost the bass level.The BASS indicator lights up on the display.

B.BOOST OFF Select to deactivate the Bass Boost.

Initial setting: B.BOOST OFF

NOTE

This function affects only the sound coming out through the frontspeakers.



Press SOUND, then press BASSBOOST repeatedly.

• Each time you press BASS BOOST, theBass Boost turns on and off alternately.

NOTE


Attenuating the input signal—INPUT ATTWhen the input level of analog source is too high, the sound willbe distorted. If this happens, you need to attenuate the inputsignal level to prevent the sound distortion.• Once you have made an adjustment, it is memorized for each

source.• You cannot use the remote control for this setting.

ATT ON Select to attenuate the input signal level.The ATT indicator lights up on the display.

ATT NORMAL Select to deactivate attenuation.

Initial setting: ATT NORMAL

3

1

2

22-24RX-F10S[J]_f.p65 04.4.22, 15:2524

25

Tun

er o

per

atio

ns

Tuner operations

When operating the receiver using the remote control,set the mode selector to “AUDIO/TV/VCR/DBS.”

Tuning in to stations manuallyFrom the remote control ONLY:

1 Press FM/AM to select the band.The last received station of the selected band is tuned in.• Each time you press the button, the band alternates

between FM and AM.

2 Press repeatedly or hold TUNING 9 or( TUNING until the station you want is tunedin.

• Pressing (or holding) TUNING 9 increases the frequency.• Pressing (or holding) ( TUNING decreases the frequency.

NOTES

• When you hold and release TUNING 9 or ( TUNING, thefrequency keeps changing until a station is tuned in.

• When a station of sufficient signal strength is tuned in, theTUNED indicator lights up on the display.

• When an FM stereo program is received, the ST (stereo)indicator also lights up.

Using preset tuningOnce a station is assigned a channel number, the station can bequickly tuned simply by selecting the number. You can preset up to30 FM and 15 AM stations.

To store the preset stationsBefore you start, remember...



1 Tune in to the station you want to preset (see“Tuning in to stations manually” above).• If you want to store the FM reception mode for this station,

select the FM reception mode you want. See “Selecting theFM reception mode” on page 26.

2 Press MEMORY.The channel number position starts flashing on the display forabout 5 seconds.

CONTINUED ON THE NEXT PAGE

Tuner operations are mainly done from the remote control.

NOTE

When you have selected “FM” or “AM” by using SOURCESELECTOR on the front panel, the remote control may notwork for tuner operations. To use the remote control for tuneroperations, select “FM” or “AM” by using the source selectingbutton on the remote control.

EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



25-26RX-F10S[J]_f.p65 04.4.22, 15:2525

26

Tun

er o

per

atio

ns

3 Press the numeric buttons (1 – 10, +10) toselect a channel number while the channelnumber position is flashing.• For channel number 5, press 5.• For channel number 15, press +10, then 5.• For channel number 30, press +10, +10, then 10.

4 Press MEMORY again while the selectedchannel number is flashing on the display.The selected channel number stops flashing.The station is assigned to the selected channel number.

5 Repeat steps 1 to 4 until you store all thestations you want.

To erase a stored preset station

Storing a new station on a used channel number erases thepreviously stored one.

To tune in a preset stationFrom the remote control:

1 Press FM/AM to select the band.The last received station of the selected band is tuned in andthe numeric buttons now work for tuner operations.• Each time you press the button, the band alternates

between FM and AM.

2 Press the numeric buttons (1 – 10, +10) toselect a preset channel number.

• For channel number 5, press 5.• For channel number 15, press +10, then 5.• For channel number 30, press +10, +10, then 10.

EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



2 1, 3

On the front panel:



1 Turn SOURCE SELECTOR to select “FM” or“AM.”The last received station of the selected band is tuned in.

2 Press TUNER PRESET.“P” appears on the display and MULTI JOG now works forselecting preset channels.

3 Turn MULTI JOG to select a preset channelnumber while “P” appears on the display.• To increase the preset channel numbers, turn MULTI JOG

clockwise.• To decreases the preset channel numbers, turn MULTI JOG

counterclockwise.

Selecting the FM reception modeWhen an FM stereo broadcast is hard to receive or noisy, you canchange the FM reception mode while receiving an FM broadcast.• You can store the FM reception mode for each preset station

(see page 25).

From the remote control ONLY:While listening to an FM station, press FM MODE.• Each time you press the button, the FM reception mode

alternates between “AUTO MUTING” and “MONO.”

AUTO MUTING Normally select this.When a program is broadcast in stereo,you will hear stereo sound; when inmonaural, you will hear monaural sound.This mode is also useful to suppressstatic noise between stations. The AUTOMUTING indicator lights up on the display.

MONO Select this to improve the reception (butstereo effect will be lost).In this mode, you will hear noise whiletuning in to the stations. The AUTOMUTING indicator goes off from thedisplay. (The ST indicator also goes off.)

Initial setting: AUTO MUTING

25-26RX-F10S[J]_f.p65 04.4.22, 15:2526

27

Cre

atin

g r

ealis

tic

sou

nd

fie

lds

Creating realisticsound fields

Reproducing theater ambienceIn a movie theater, many speakers are located on the walls toreproduce impressive multi-channel sound, reaching you from alldirections.With these many speakers, sound localization and soundmovement can be expressed.Surround/DSP modes built in this receiver can create almost thesame Surround sound as you can feel in a real movie theater.

Introducing the Surround modes Dolby Digital*Dolby Digital is a digital signal compression method, developed byDolby Laboratories, and enables multi-channel encoding anddecoding.• When Dolby Digital signal is detected through the digital input,

the DOLBY D indicator lights up on the display.

Dolby Digital 5.1CHDolby Digital 5.1CH (DOLBY D) encoding method records anddigitally compresses the left front channel, right front channel,center channel, left surround channel, right surround channel, andLFE channel signals (total 6 channels, but the LFE channel iscounted as 0.1 channel. Therefore, called 5.1 channel).Dolby Digital enables stereo surround sounds, and sets the cutofffrequency of the surround treble at 20 kHz, compared to 7 kHz forDolby Pro Logic. As such, the sound movement and “being-there”feeling are enhanced much more than Dolby Pro Logic.

Dolby Digital EXDolby Digital EX (DOLBY D EX) is a digital surround encodingformat that adds the third surround channels, called “surroundback.”Compared to the conventional Dolby Digital 5.1CH, these newlyadded surround back channels can reproduce more detailedmovements behind you while viewing the video software. Inaddition, surround sound localization will become more stable.

Dolby SurroundDolby Pro Logic IIDolby Pro Logic II is a multi-channel playback format to convert2-channel software into 5-channel (plus subwoofer). The matrix-based conversion method used for Dolby Pro Logic II makes nolimitation for the cutoff frequency of the surround treble andenables stereo surround sound.• This receiver provides two types of Dolby Pro Logic II modes—

Pro Logic II Movie (PLII MOVIE) and Pro Logic II Music (PLIIMUSIC).When Dolby Pro Logic II is activated, the indicator lightsup on the display.

PLII MOVIE Suitable for playing any Dolby Surround encodedsoftware. You can enjoy a sound field very closeto the one created with discrete 5.1-channelsounds.

PLII MUSIC Suitable for playing any 2-channel stereosoftware. You can enjoy wide and deep sounds.

• To enjoy software encoded with Dolby Digital, connect thesource component using the digital terminal on the rear of thisreceiver. (See page 11.)

* Manufactured under license from Dolby Laboratories.“Dolby”, “Pro Logic”, and the double-D symbol aretrademarks of Dolby Laboratories.

27-31RX-F10S[J]_f.p65 04.4.22, 15:2627

28

Cre

atin

g r

ealis

tic

sou

nd

fie

lds

DTS**DTS is another digital signal compression method, developed byDigital Theater Systems, Inc., and enables multi-channelencoding and decoding (1ch up to 6.1ch).• When DTS signal is detected through the digital input, the DTS

indicator lights up on the display.

DTS Digital SurroundDTS Digital Surround (DTS) is another discrete 5.1 channeldigital audio format available on CD, LD, and DVD software.Compared to Dolby Digital, the DTS Digital Surround format has alower audio compression rate which enables it to add breadth anddepth to the sounds reproduced. As such, DTS Digital Surroundfeatures natural, solid, and clear sound.

DTS Extended Surround (DTS-ES)DTS-ES is another multi-channel digital encoding format.It greatly improves the 360-degree surround impression andspace expression by adding the third surround channel—surroundback channel.DTS-ES includes two signal formats with different surround signalrecording methods—DTS-ES Discrete 6.1ch (ES DISCRETE)and DTS-ES Matrix 6.1ch (ES MATRIX).DTS-ES Discrete 6.1ch has been designed to encode (anddecode) a 6.1-channel signal discretely to avoid interference witheach channel.DTS-ES Matrix 6.1ch has been designed to add an extrasurround channel to DTS Digital Surround 5.1-channel. By using amatrix encoding/decoding method, an additional “surround back”channel signal is encoded (and decoded) in both the left and rightsurround channel signals.

DTS 96/24In recent years, there has been increasing interest in highersampling rates both for recording and for reproducing at home.Higher sampling rates allow wider frequency range and greater bitdepths provide extended dynamic range.DTS 96/24 is a multi-channel digital signal format (fs 96 kHz/24bits) introduced by Digital Theater Systems, Inc. to deliver “better-than-CD sound quality” into the home.• When DTS 96/24 signal is detected, the DTS and 96/24

indicators light up. You can enjoy its 5.1-channel sound with full-quality.

DTS Neo:6DTS Neo:6 is another conversion method to create 6-channel(plus subwoofer) from analog/digital 2-channel software by usingthe high precision digital matrix decoder used for DTS-ES Matrix6.1ch.• This receiver provides the following DTS Neo:6 modes—Neo:6

Cinema (NEO:6CINEMA) and Neo:6 Music (NEO:6 MUSIC).When one of them is activated, the NEO:6 indicator lights up onthe display.

NEO:6CINEMA Suitable for playing movies. You can get thesame atmosphere with 2-channel software aswith 6.1-channel software. It is also effective forplaying software encoded with conventionalsurround formats.

NEO:6 MUSIC Suitable for playing music software. The frontchannel signals bypass the decoder (resulting inno loss of sound quality) and the surroundsignals transmitted through the other speakersexpand the sound field naturally.

** “DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarksof Digital Theater Systems, Inc.

When using Surround mode, the sounds come out of theactivated speakers which the Surround mode requires.

• If either the surround speakers or center speaker is set to“NO” in the speaker setting (see page 18), the correspondingchannel signals are allocated to and emitted through the frontspeakers.

• If both the surround speakers and center speaker are set to“NO” in the speaker setting (see page 18), JVC’s original 3D-PHONIC processing (which has been developed to create thesurround effect through the front speakers only) is used. The 3Dindicator lights up on the display.

3D HEADPHONE modeIf you connect a pair of headphones while one of the Surroundmodes is in use, the 3D HEADPHONE mode is activatedwithout respect to the type of software played back.“3DHEADPHONE” appears on the display and the DSP, 3D,and HP indicators light up.

About other digital signalsLinear PCM

Uncompressed digital audio data used for DVDs, CDs, andVideo CDs.DVDs support 2 channels with sampling rates of 48/96 kHz, atquantization of 16/20/24 bits. On the other hand, CDs andVideo CDs are limited to 2 channels with 44.1 kHz at 16 bits.• When Linear PCM signal is detected, the LPCM indicator

lights up.

Dual Mono

Dual Mono can be easily understood when you think of thebilingual broadcast for TV programs (however, the Dual Monoformat is not identical with those analog formats).This format is now adopted in Dolby Digital, DTS, and so on. Itallows two independent channels (called main channel andsub-channel) to be recorded separately.• You can select either channel you want to listen to (see

page 20).

27-31RX-F10S[J]_f.p65 04.4.22, 15:2628

29

Cre

atin

g r

ealis

tic

sou

nd

fie

lds

3D HEADPHONE modeIf you connect a pair of headphones while one of the DSPmodes is in use, the 3D HEADPHONE mode is activatedwithout respect to the type of software played back.“3DHEADPHONE” appears on the display and the DSP, 3D,and HP indicators light up.

Introducing the DSP modesThe sound heard in a concert hall, club, etc. consists of directsound and indirect sound—early reflections and reflections frombehind. Direct sounds reach the listener directly without anyreflection. On the other hand, indirect sounds are delayed by thedistances of the ceiling and walls. These direct sounds andindirect sounds are the most important elements of the acousticsurround effects.The DSP modes can create these important elements, and giveyou a real “being there” feeling.

The DSP modes include the following modes:• Digital Acoustic Processor (DAP) modes—HALL1, HALL2, LIVE

CLUB, DANCE CLUB, PAVILION, THEATER1, THEATER2• MONO FILM—Used for all types of 2-channel signals (including

Dual Mono signal)• All Channel Stereo mode (ALL CH ST.)

When one of the DSP modes is activated, the DSP indicator lightsup on the display.

Digital Acoustic Processor (DAP) modesYou can use the following DAP modes in order to reproduce amore acoustic sound field in your listening room.

HALL1 Reproduces the spatial feeling of a largeshoebox-shaped hall designed primarily forclassical concerts. (Its seating capacity is about2000.)

HALL2 Reproduces the spatial feeling of a largevineyard-shaped hall designed primarily forclassical concerts. (Its seating capacity is about2000.)

LIVE CLUB Reproduces the spatial feeling of a live music clubwith a low ceiling.

DANCE CLUB Reproduces the spatial feeling of a rocking danceclub.

PAVILION Reproduces the spatial feeling of an exhibitionhall with a high ceiling.

THEATER1 Reproduces the spatial feeling of a large theaterwhere the seating capacity is about 600.

THEATER2 Reproduces the spatial feeling of a small theaterwhere the seating capacity is about 300.

NOTE

When “THEATER1” or “THEATER2” is activated while playingback 2-channel analog or digital source, the built-in Dolby ProLogic II decoder is activated and the indicator lights up.

Early reflections

Direct sounds

Reflections from behind

When using the DAP mode, the sounds come out of all theconnected and activated speakers.

• If the surround speakers are set to “NO” in the speakersetting (see page 18), JVC’s original 3D-PHONIC processing(which has been developed to create the surround effectthrough the front speakers only) is used.The 3D indicator lights up on the display.

MONO FILMIn order to reproduce a more acoustic sound field in your listeningroom while viewing monaural sound video software (analog and2-channel digital signals including Dual Mono signal), you can usethis mode.The surround effect will be added, and the sound localization ofactor’s words will be improved.

This mode cannot be used for multi-channel digital signals.

When “MONO FILM” is used, sounds come out of all theconnected (and activated) speakers.• If the surround speakers are set to “NO” in the speaker

setting (see page 18), JVC’s original 3D-PHONIC processing(which has been developed to create the surround effectthrough the front speakers only) is used.The 3D indicator lights up on the display.

• If incoming signals change from 2-channel digital signal toanother digital signal type, “MONO FILM” is canceled and anappropriate Surround mode is activated.

All Channel Stereo mode (ALL CH ST.)This mode can reproduce a larger stereo sound field using all theconnected (and activated) speakers. This mode cannot be usedif the surround speakers are set to “NO” in the speakersetting (see page 18).

Sound reproduced fromnormal stereo

Sound reproduced from AllChannel Stereo mode

27-31RX-F10S[J]_f.p65 04.4.22, 15:2629

30

Cre

atin

g r

ealis

tic

sou

nd

fie

lds

DSP modes

HALL1/2,

LIVE CLUB,

DANCE CLUB,

PAVILION,

THEATER1/2,

ALL CH ST.

Using the Surround/DSP modesAvailable Surround/DSP modes vary depending on the speaker settings and the incoming signals. See the table below.• The numbers inside the parentheses following the incoming signal type indicate the number of the front channels and that of the

surround channels. For example, (3/2) indicates that the signals are encoded with three front signals (left/right/center) and two (stereo)surround signals.

• For EX/ES setting, see page 20.

Incoming signal

Dolby Digital EX

Dolby Digital (3/2, 2/2)

Dolby Digital(3/1, 2/1, 3/0, 1/0)

DTS-ES Discrete 6.1 ch

DTS-ES Matrix 6.1 chDTS-ES 96/24 Matrix

DTS, DTS 96/24 (3/2, 2/2)

DTS (3/1, 2/1, 3/0, 1/0)

Incoming signals Available Surround modes Available DSP modes

Dolby Digital (Dual Mono)DUAL MONO

DTS (Dual Mono) HALL1/2, LIVE CLUB,

Dolby Digital (2-channel) DANCE CLUB, PAVILION,

DTS (2-channel) PLII MOVIE, PLII MUSIC, THEATER1/2, MONO FILM,

Linear PCM NEO:6CINEMA, NEO:6 MUSIC ALL CH ST.

Analog

DVD MULTI None None

Surround backspeaker setting(SML/LRG/NO)

SML/LRG

NO

SML/LRG

NO

SML/LRG/NO

SML/LRG

NO

SML/LRG

NO

SML/LRG

NO

SML/LRG/NO

EX/ES setting(AUTO/ON/OFF)

AUTO/ON

OFF

AUTO/ON

OFF

ON

AUTO/OFF

ON

AUTO/OFF

AUTO/ON/OFF

AUTO/ON

OFF

AUTO/ON

OFF

AUTO/ON

OFF

AUTO/ON

OFF

ON

AUTO/OFF

ON

AUTO/OFF

AUTO/ON/OFF

Virtual Surround BackIf you have connected (and activated) the surround speakers,you can use Virtual Surround Back when playing back DolbyDigital EX or DTS-ES software without connecting thesurround back speaker.This function creates the great surround effect from the behindas if you have connected the surround back speaker. TheVIRTUAL SB (Surround Back) indicator lights up on thedisplay.

NOTES

• For some Dolby Digital EX software, Dolby Digital 5.1-channelreproduction (“DOLBY D”) is applied.

• DTS 96/24 processing is not applied when the EX/ES setting isactivated. If you want to apply the processing, set the EX/ESsetting to “EX/ES : OFF” (see page 20).

• You cannot select “ALL CH ST.” when the surround speakersare set to “NO” in the speaker setting (see page 18).

Surround mode

DOLBY D EX

DOLBY D

DOLBY D (Virtual Surround Back)

DOLBY D

DOLBY D EX

DOLBY D

DOLBY D (Virtual Surround Back)

DOLBY D

DOLBY D

ES DISCRETE

DTS

DTS (Virtual Surround Back)

DTS

ES MATRIX

DTS


DTS

DTS NEO:6

DTS


DTS

DTS

27-31RX-F10S[J]_f.p65 04.4.22, 15:2630

31

Cre

atin

g r

ealis

tic

sou

nd

fie

lds

On the front panel:



1 Select and play any source other than “DVDMULTI.”• Make sure you have selected the input mode (analog or

digital) correctly.

2 Press SURROUND.MULTI JOG now works for selecting Surround/DSP modes.

3 Turn MULTI JOG to select the Surround/DSPmode you want.Ex.: When “DOLBY D” is selected for Dolby Digital multi-

channel software:

To cancel Surround/DSP modes

Turn MULTI JOG so that “SURRND OFF” appears on the display.

Activating the Surround/DSP modesAvailable Surround/DSP modes vary depending on the speakersettings and the incoming signals. For details, see page 30.

Activating one of the Surround/DSP modes automaticallyrecalls the memorized settings and adjustments.

• To adjust the speaker output level, see page 23.

• To adjust the effect level for the DSP mode (except AllChannel Stereo mode), see page 23.

• To add “wraparound” sound effect to “PLII MUSIC”(PANORAMA control), see page 23.

• To adjust the sound localization of the center channelfor “NEO:6 MUSIC” (center gain), see page 24.

NOTES

• You cannot use any Surround/DSP modes when selecting “DVDMULTI” as the playback source.

• You cannot select All Channel Stereo mode if the surroundspeakers are set to “NO” in the speaker setting (see page 18).

If “AUTO SURRND (Auto Surround)” is set to “ON”

You can enjoy Surround mode simply by playing back multi-channel software (with digital input selected for that source).To activate Auto Surround, see page 21.


When operating the receiver usingthe remote control, set the modeselector to “AUDIO/TV/VCR/DBS.”

1 Select and play any source other than “DVDMULTI.”• Make sure you have selected the input mode (analog or

digital) correctly.

2 Press SURROUND repeatedly to select theSurround/DSP mode you want.Ex.: When “DOLBY D” is selected for Dolby Digital multi-

channel software:

To cancel Surround/DSP modes

Press SURROUND repeatedly so that “SURRND OFF” appearson the display.

2 1, 3

EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



EQLPCM L

LS SB RS

S . WFR

PLNEO : 6DSP 3D

LFE



1

2

27-31RX-F10S[J]_f.p65 04.4.22, 15:2631

32

AV

CO

MP

U L

INK

rem

ote

co

ntr

ol s

yste

m

AV COMPU LINKremote controlsystem

The AV COMPU LINK remote control system allows you tooperate JVC’s video components (TV, DVD player*, and VCR)through this receiver.

This receiver is equipped with the AV COMPU LINK-III, which hasadded a function to operate JVC’s video components through thecomponent video jacks. To use this remote control system, youneed to connect the video components you want to operate,following the diagrams below and the procedures on page 33.• Refer also to the manuals supplied with your video components.

* “DVD player” on pages 32 and 33 can be replaced with “DVDrecorder.”

Connections 1: AV COMPU LINK connection

Connections 2: Video cable connectionThis receiver is equipped with three types of the video terminals—composite video, S-video, and component video, and the signalscoming into this receiver through one type of video terminals canoutput only through the terminal of the same type. So you need toconnect the video components to this receiver using one of thefollowing three ways.• When using the AV COMPU LINK remote control system, set

the video input for the DVD player and the VCR correctly (see“Selecting the component video input mode—DVD VIDEO/VCRVIDEO” on page 21); otherwise, the correct input for thisreceiver will not be selected on the TV.

To video input 1

S-video cable S-video cable

VCR

DVD player

TV

Monaural mini-plugs(not supplied)

Case 1:When connecting the source equipment to the receiverthrough the S-video terminals, connect this receiver to theTV’s video input 1 terminal using S-video cables.

Monauralmini-plugs(not supplied)

IMPORTANT:

The AV COMPU LINK remote control system cannot control theDBS tuner connected to the DBS IN jacks.

NOTES

• When connecting the receiver and a TV with the AV COMPU LINKEX terminal by using a component video cable, you cannot useAutomatic selection of TV’s input mode (see page 33).

• When connecting only the VCR and DVD player to this receiver,connect it directly to the receiver using cable with the monauralmini-plugs.

• You can connect only the TV with AV COMPU LINK EX or AVCOMPU LINK-III terminal to the AV COMPU LINK-III terminal.

Case 2:When connecting the source equipment to the receiverthrough the composite video jacks, connect this receiverto the TV’s video input 2 terminal (composite video input)using composite video cables.

Case 3:When connecting the source equipment to the receiverthrough the component video jacks, connect this receiverto the TV’s video input 2 terminals (component videoinput) using component video cables.

To video input 2(Composite)

Composite video cable Composite video cable

To video input 2(Component)

Component video cable Component video cable

TVRX-F10SSourceequipment

AVCOMPU LINK-III

AVCOMPU LINK EX

AVCOMPU LINK-III

AVCOMPU LINK

AVCOMPU LINK



32-33RX-F10S[J]_f.p65 04.4.22, 15:2632

33

AV

CO

MP

U L

INK

rem

ote

co

ntr

ol s

yste

m

One-touch DVD playSimply by starting playback on the DVD player, you can enjoy theDVD playback without setting other switches manually.• When the DVD player is connected through the analog input

jacks on this receiver (and analog input is selected), thereceiver automatically turns on and changes the source to“DVR/DVD” or “DVD MULTI.”

• When the DVD player is connected through the digital inputterminal on this receiver (and digital input is selected), thereceiver automatically turns on and changes the source to“DVR/DVD DGT.”

The TV automatically turns on and changes the input mode to theappropriate position so that you can view the playback picture.

Automatic selection of TV’s input mode• When you select “TV” (or “TV DIGITAL”) as the source to play on

the receiver, the TV automatically changes the input mode tothe TV tuner so that you can watch TV.

• When you select “DVR/DVD” (or “DVR/DVD DGT”), “DVDMULTI,” “VCR” (or “VCR DIGITAL”), or “DBS” (or “DBS DIGITAL”)as the source to play on the receiver, the TV automaticallychanges the input mode to the appropriate position (either videoinput 1 or video input 2) so that you can view the playbackpicture.

NOTE

This function does not work when you connect this receiver andthe TV with the AV COMPU LINK EX terminal using a componentvideo cable. In this case, reconnect the TV referring to Case 1 orCase 2 on page 32.

Automatic power on/offThe TV, DVD player, and VCR turn on and off along with thereceiver.When you turn on the receiver;• If the previously selected source is “TV” (or “TV DIGITAL”) or

“DBS” (or “DBS DIGITAL”), only the TV will turn on automatically.• If the previously selected source is “DVR/DVD” (or “DVR/DVD

DGT”) or “DVD MULTI,” the TV and DVD player will turn onautomatically.

• If the previously selected source is “VCR” (or “VCR DIGITAL”),the TV and VCR will turn on automatically.

When you turn off the receiver, the TV, DVD player, and VCR willturn off.

NOTE

If you turn off the receiver while recording on the VCR, the VCRwill not turn off, but continue recording.

Connecting procedure

1 If you have already plugged your VCR, DVDplayer, TV, and this receiver into the ACoutlets, unplug their AC power cords first.

2 Connect your VCR, DVD player, TV, and thisreceiver as follows, using the cables with themonaural mini-plugs (not supplied).• See “Connections 1” on the previous page.

3 Connect the audio input/output jacks on theVCR, DVD player, TV, and this receiver usingthe audio cables.• See pages 7 to 10.

4 Connect the video input/output jacks on theVCR, DVD player, TV, and this receiver usingthe S-video cables, composite video cables,or component video cables.• See “Connections 2” on the previous page.

5 Plug the AC power cords of the connectedcomponents and this receiver into the ACoutlets.

6 When turning on the TV for the first time afterthe AV COMPU LINK connection, turn the TVvolume to the minimum using the TV volumecontrol on the TV.

7 Turn on other connected components first,then turn on this receiver.• When turning on the VCR, use the remote control supplied

with this receiver (press VCR ).

The AV COMPU LINK remote control system allows you to usethe five basic functions listed below.

Remote control of the TV, DVD player, and VCR using thisremote controlSee pages 34 and 35 for details.• Aim the remote control directly at the remote sensor on each

component.

One-touch video playSimply by inserting a video cassette without its safety tab into theVCR, you can enjoy the video playback without setting otherswitches manually. The receiver automatically turns on andchanges the source to “VCR” (or “VCR DIGITAL”).The TV automatically turns on and changes the input mode to theappropriate position so that you can view the playback picture.When you insert a video cassette with its safety tab, press theplay (3) button on the VCR or on the remote control. So, you canget the same result.

32-33RX-F10S[J]_f.p65 04.4.22, 15:2633

34

You can use the supplied remote control to operate not onlythis receiver but also other JVC products.

• Refer also to the manuals supplied with the other products.– Some JVC VCRs can accept two types of the control

signals—remote codes “A” and “B.” This remote control canoperate a VCR whose remote control code is set to “A.”

– Some JVC DVD recorders can accept four types of the controlsignals. This remote control can operate a DVD recorderwhose remote control code is set to the initial code. Fordetails, refer to the manual supplied with the DVD recorder.

• To operate other products, aim the remote control directly at theremote sensor on the target product.

7 TV

Operating otherJVC products

Op

erat

ing

oth

er J

VC

pro

du

cts

You can always perform the following operations:

TV : Turn on or off the TV.

TV VOL +/–: Adjust the volume on the TV.

TV/VIDEO: Change the input mode (either video inputor TV tuner) on the TV.

After pressing TV, you can perform the following operations on theTV.

CHANNEL +/–: Change the channel numbers.

1 – 9, 0, 100+: Select the channel numbers.

TV RETURN (10): Function as the TV RETURN button.(Switches between the previous channeland the current channel.)

Set the mode selector to“AUDIO/TV/VCR/DBS.”

7 VCR

You can always perform the following operation:

VCR : Turn on or off the VCR.

After pressing VCR, you can perform the following operations onthe VCR.

CHANNEL +/–: Change the channel numbers on the VCR.

1 – 9, 0: Select the channel numbers on the VCR.

3: Start playback.

7: Stop playback.

8: Pause playback. To release it, press 3.

¡: Fast-wind a tape.

1: Rewind a tape.

REC PAUSE: Enter recording pause. To start recording,press this button then 3.

Set the mode selector to“AUDIO/TV/VCR/DBS.”

34-38RX-F10S[J]_f.p65 04.4.22, 15:2634

35

7 DVD recorder or DVD player

To operate the DVDrecorder, set the modeselector to “DVR.”

To operate the DVD player,set the mode selector to“DVD.”

Op

erat

ing

oth

er J

VC

pro

du

cts

After setting the mode selector correctly, you can perform thefollowing operations on the DVD recorder or DVD player.

See the instructions supplied with the DVD recorder or DVDplayer for details.

DVR/DVD : Turn on or off the DVD recorder or DVD player.

3: Start playback.

7: Stop playback.

8: Pause playback. To release it, press 3.

¢: Skip to the beginning of the next chapter.

4: Return to the beginning of the current (orprevious) chapter.

¡: Fast-forward playback.

1: Fast-reverse playback.

TOP MENU/MENU:Display the menu recorded on discs.

ON SCREEN: Shows the on-screen bar.

5/∞/3/2: Select an item on the menu screen.

ENTER: Enter the selected item, channel number,chapter/title number, or track number (ifrequired).

You can also use the following buttons to operate JVC DVDrecorder and/or DVD player if it supports the correspondingfunction:

For various settings:

AUDIO*: Select the audio language/channel.

SUBTITLE: Select the subtitle language.

SET UP: Display the Preference display.

VFP: Show the picture adjustment screen.

PROGRESSIVE*: Change the scanning mode.

ANGLE: Select the view angle.

* Press and hold when using these buttons.

For various playback:

(one touch replay): Move the playback position back 10seconds before the current position.

RETURN: Return to the main menu during menuoperation.

CANCEL: Cancel the programmed track, etc.

Only for DVD recorder operations:


DVD/HDD: Select the DVD recorder or HDD deck. (Only fora DVD recorder incorporated with HDD deck.)

(skip): Move the playback position ahead 30 secondsafter the current position.

1 – 9, 0: Select a channel number (while stopped) or achapter/title number, track number (while playingback). Press ENTER to enter the number.

REC MODE: Select the recording mode.

REC PAUSE: Enter recording pause. To start recording,press 3.

DISPLAY: Change the display information.

Only for DVD player operations:

fs/Rate: Show the sampling frequency.

TITLE/GROUP: Make the numeric buttons work for selecting thetitle/group number.

ZOOM: Zoom in and out.

1 – 10, 0, +10: Select a chapter/title number, track number,menu item, etc.

DVD/CARD: Select the disc or memory card to play. (Only fora DVD player incorporated with memory cardslots.)

DIMMER: Change the display brightness.

THUMBNAIL: Show the thumbnail screen for JPEG discs.

SLIDE: Start the slide show playback for JPEG discs.

3D/S.EFFECT: Apply the 3D effect.

PAGE: Show browsable still pictures recorded on DVD-Audio discs.

If these buttons do not function normally, use the remotecontrol supplied with your DVD recorder or DVD player.Refer also to the manuals supplied with the DVD recorderor DVD player for details.

34-38RX-F10S[J]_f.p65 04.4.22, 16:1335

36

Manufacturer Codes

JVC 01Akai 02Bell+Howell 03Centurion 04Coronad 05Daewoo 06, 07, 08Emerson 09, 10, 11, 12, 13Fisher 14GE•Pana 15, 16GE•RCA 17Gold Star 18, 19Hitachi 20, 21KTV 22, 23Magnavox 24Marantz 25Mitsubishi 25Panasonic 26, 27Philips 24Pioneer 28Proscan 29Quasar 30Radioshack 31RCA 02, 17, 32, 33, 34, 35Samsung 36, 37Sanyo 14Sears 38Sharp 39Sony 40Symphonic 41, 42Toshiba 38Zenith 43, 44

Initial setting: 01

By changing the transmittable signals, you can use thesupplied remote control to operate other manufacturers’products.

• Refer also to the manuals supplied with the other products.• To operate those components with the remote control, first you

need to set the manufacturers’ codes each for the CATVconverter, DBS tuner, VCR, and TV.

• After replacing batteries of the remote control, set themanufacturers’ codes again.

Changing the transmittable signals for operatinga TV


1 Press and hold TV .2 Press TV.

3 Enter the manufacturer’s code using buttons1 – 9, and 0.See “Manufacturers’ codes for TV” on the right.

4 Release TV .Now, you can perform the following operations on the TV.

TV : Turn on or off the TV.

TV VOL +/–: Adjust the volume on the TV.

TV/VIDEO: Change the input mode (either TV orVIDEO).

After pressing TV, you can perform the following operations onthe TV.


1 – 9, 0, 100+ (+10): Select the channel numbers.

See the instructions supplied with the TV for details.

5 Try to operate your TV by pressing TV .When your TV turns on or off, you have entered the correctcode.

If more than one code is listed for your brand of TV, try eachone until the correct one is entered.

Operating othermanufacturers’products

Op

erat

ing

oth

er m

anu

fact

ure

rs’ p

rod

uct

sManufacturers’ codes for TV

Manufacturers’ codes are subject to change withoutnotice. If they are changed, this remote control cannotoperate the equipment.

34-38RX-F10S[J]_f.p65 04.4.22, 15:2636

37

Op

erat

ing

oth

er m

anu

fact

ure

rs’ p

rod

uct

s

Changing the transmittable signals for operatinga VCR


1 Press and hold VCR .

2 Press VCR.

3 Enter the manufacturer’s code using buttons1 – 9, and 0.See “Manufacturers’ codes for VCR” on the right.

4 Release VCR .Now, you can perform the following operation on the VCR.

VCR : Turn on or off the VCR.

After pressing VCR, you can perform the following operationson the VCR.

CHANNEL +/–: Change the channel numbers on theVCR.

1 – 9, 0: Select the channel numbers on the VCR.

3: Start playback.

7: Stop playback.

8: Pause playback.

¡: Fast-wind a tape.

1: Rewind a tape.

See the instructions supplied with the VCR for details.

5 Try to operate your VCR by pressing VCR .When your VCR turns on or off, you have entered the correctcode.

If more than one code is listed for your brand of VCR, try eachone until the correct one is entered.

Manufacturer Codes

JVC 01, 02, 03, 04Aiwa 05Akai 06, 07, 08Bell+Howell 09Daewoo 10Emerson 11, 12, 13, 14, 15Fisher 16, 17, 18, 19G.E. 20, 21Go Video 22Gold Star 23Go-Video A 24Go-Video B 25Hitachi 20, 26Magnavox 27, 28, 29Mitsubishi 30, 31, 32, 33NEC 34, 35Panasonic 36, 37Philips 27RCA 38Samsung 39, 40, 41Sanyo 16, 17, 18, 19Scott 42Sharp 43, 44Shintom 45Sony 46, 47, 48, 49, 50, 51Symphonic 52Teknica 53, 54Toshiba 55Zenith 56

Initial setting: 01

Manufacturers’ codes for VCR


34-38RX-F10S[J]_f.p65 04.4.22, 15:2637

38


Op

erat

ing

oth

er m

anu

fact

ure

rs’ p

rod

uct

s Changing the transmittable signals for operating

a CATV converter or DBS tunerSet the mode selector to “AUDIO/TV/VCR/DBS.”

1 Press and hold DBS .

2 Press DBS.

3 Enter the manufacturer’s code using buttons1 – 9, and 0.See “Manufacturers’ codes for CATV converter” or“Manufacturers’ codes for DBS tuner” below.

4 Release DBS .Now, you can perform the following operation on the CATVconverter or DBS tuner.

DBS : Turn on or off the CATV converter orDBS tuner.

After pressing DBS, you can perform the following operationson the CATV converter or DBS tuner.

CHANNEL +/–: Change the channel numbers on theCATV converter or DBS tuner.

1 – 9, 0: Select the channel numbers on theCATV converter or DBS tuner.

See the instructions supplied with the CATV converter or DBStuner for details.

5 Try to operate your CATV converter or DBStuner by pressing DBS .When your CATV converter or DBS tuner turns on or off, youhave entered the correct code.

If more than one code is listed for your brand of CATVconverter or DBS tuner, try each one until the correct one isentered.

Changing the transmittable signals for operatinga DVD player

Set the mode selector to “DVD.”

1 Press and hold DVR/DVD .2 Press DVR/DVD.

3 Enter the manufacturer’s code using buttons1 – 9, and 0.See “Manufacturers’ codes for DVD player” below.

4 Release DVR/DVD .Now, you can perform the following operation on the DVDplayer.

DVR/DVD : Turn on or off the DVD player.

3: Start playback.

1: Retun to the beginning of the currentchapter (or fast-forward for some models).

¡: Skip to the beginning of the next chapter(or fast-reverse for some models).

7: Stop playback.

8: Pause playback.

MENU: Display the menu recorded on DVDVIDEO discs.

5/∞/3/2: Select an item on the menu screen.

ENTER: Enter the selected item.

1 – 9, 0: Select the chapter number.

See the instructions supplied with the DVD player for details.

5 Try to operate your DVD player by pressingDVR/DVD .When your DVD player turns on or off, you have entered thecorrect code.

If more than one code is listed for your brand of DVD player,try each one until the correct one is entered.

Manufacturer Codes

JVC 01Hitachi 12Kenwood 05, 08Mitsubishi 10Onkyo 15, 16Panasonic 04Philips 07Pioneer 03Samsung 14Sony 02Toshiba 06Yamaha 09

Initial setting: 01

Manufacturers’ codes for DVD player

Manufacturers’ codes for DBS tuner

Manufacturer Codes

Echostar 40G.I. 41Hitachi 42Hughes 43Panasonic 44Primestar 45RCA 46Sony 47Toshiba 48

Initial setting: 01

Manufacturers’ codes for CATV converter

Manufacturer Codes

G.I. 01Gemini 02Hamlin 03, 04, 05, 06Jerrold 07, 08, 09, 10, 11, 12, 13, 14, 15Macom 16, 17, 18Magnavox 19Oak 20, 21, 22Panasonic 23, 24Philips 25, 26, 27, 28, 29, 30Pioneer 31, 32S. Atlanta 33, 34, 35Samsung 36Tocom 37Zenith 38, 39

NOTE

You cannot use this remote control to operate othermanufacturers’ DVD recorder.

34-38RX-F10S[J]_f.p65 04.4.22, 15:2638

39

Tro

ubl

esh

oo

tin

g

Troubleshooting

PROBLEM

The power does not come on.

The receiver turns off (enters standbymode).

“OVER HEAT” flashes on the display,then the receiver turns off.

No sound from speakers.

Sound from one speaker only.

Bass sound is reinforced too muchwhen listening in stereo.

Sounds are intermittently distorted bythe outside noise such as a lightningdischarge.

Remote control does not operate asyou intend.

Remote control does not work.

Buttons cannot be used.

Continuous hiss or buzzing during FMreception.

Occasional cracking noise during FMreception.

Use this chart to help you solve daily operational problems. Ifthere are any problems you cannot solve, contact your JVC’sservice center.

POSSIBLE CAUSE

The power cord is not plugged in.

Speakers are overloaded because of highvolume.

Speakers are overloaded because of ashort circuit at the speaker terminals.

The receiver is overloaded because of ahigh voltage.

The receiver is overloaded because of highvolume or long time usage.

Speaker signal cables are not connected.

Connections are incorrect.

An incorrect source is selected.

Muting is activated.

An incorrect input mode (analog or digital)is selected.

TV Direct is activated.

Speaker signal cables are not connectedproperly.

Appropriate bass level is not selected.

When you use the digital coaxial connection,the sounds may be intermittently distortedby the outside noise such as a lightningdischarge but the sound will be restoredautomatically.

The remote control is not ready for yourintended operation.

There is an obstruction hiding the remotesensor on the receiver.

Batteries are weak.

The mode selector is set to the incorrectposition.

TV Direct is activated.

Incoming signal is too weak.

The station is too far away.

The wrong antenna is being used.

Antennas are not connected properly.

Ignition noise from automobiles.

SOLUTION

Plug the power cord into an AC outlet.

1. Stop the playback source.2. Turn on the receiver again, then turn the

volume down.

Check the speaker wiring. If speaker wiringis not short-circuited, contact your dealer.

Consult your dealer after unplugging thepower cord.

Turn on the receiver again. If the receiverturns off soon, consult your dealer afterunplugging the power cord.

Check speaker wiring, then reconnect ifnecessary (see page 6) after unpluggingthe power cord.

Check the audio connections (see pages 7to 11) after unplugging the power cord.

Select the correct source.

Press MUTING to cancel the mute (seepage 15).

Select the correct input mode (analog ordigital).

Deactivate TV Direct (see page 14).

Check speaker wiring and reconnect ifnecessary (see page 6) after unpluggingthe power cord.

Adjust audio position level (see page 14).

This is not a malfunction.

Set the mode selector correctly, then pressthe corresponding source selecting buttonor SOUND before operation.

Remove the obstruction.

Replace batteries.

Set the mode selector to the properposition.

Deactivate TV Direct (see page 14).

Connect an outdoor FM antenna or contactyour dealer.

Select another station.

Check with your dealer to be sure you havethe correct antenna.

Check the connections.

Move the antenna farther from automobiletraffic.

Po

wer

So

un

dR

emo

te c

on

tro

lTu

ner

39-40RX-F10S[J]_f.p65 04.4.22, 15:2639

40

Sp

ecif

icat

ion

s

Designs and specifications are subject to change withoutnotice.

AmplifierOutput PowerAt stereo operation:

Front channels: 100 W per channel, min. RMS, bothchannels driven into 6 Ω at 40 Hz to 20kHz with no more than 0.8% totalharmonic distortion.

At surround operation:

Front channels: 100 W per channel, min. RMS, driven into6 Ω at 1 kHz with no more than 0.8% totalharmonic distortion.

Center channel: 100 W, min. RMS, driven into 6 Ω at 1 kHz,with no more than 0.8% total harmonicdistortion.

Surround channels: 100 W per channel, min. RMS, driven into6 Ω at 1 kHz, with no more than 0.8%total harmonic distortion.

Surround back channel:100 W, min. RMS, driven into 6 Ω at 1 kHz,with no more than 0.8% total harmonicdistortion.

AudioAudio Input Sensitivity/Impedance:

DVR/DVD (DVD MULTI), VCR, DBS, TV:330 mV/47 kΩ

Audio Input (DIGITAL IN)*:

Coaxial: DIGITAL IN 1(DVR/DVD):0.5 V(p-p)/75 Ω

Optical: DIGITAL IN 2(DBS), 3(VCR):

–21 dBm to –15 dBm(660 nm ±30 nm)

* Corresponding to Linear PCM, Dolby Digital, and DTS (withsampling frequency—32 kHz, 44.1 kHz, 48 kHz).

Audio Output Level:

DVR, VCR, MONITOR OUT: 330 mV

Signal-to-Noise Ratio (’66 IHF/DIN): 80 dB/62 dB

Frequency Response (6 Ω): 20 Hz to 20 kHz (±1 dB)

Bass Boost: +4 dB ±1 dB at 100 Hz

Equalization (at DSP operation):

Center frequency: 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz

Control range: ±8 dB

SpecificationsVideoVideo Input Sensitivity/Impedance:

Composite video: DVR/DVD, VCR, DBS:1 V(p-p)/75 Ω

S-video: DVR/DVD, VCR, DBS:

Y (luminance): 1 V(p-p)/75 ΩC (chrominance, burst): 0.286 V(p-p)/75 Ω

Component: DVR/DVD, VCR:

Y (luminance): 1 V(p-p)/75 ΩPB, PR: 0.7 V(p-p)/75 Ω

Video Output Level/Impedance:

Composite video: DVR, VCR, MONITOR OUT:1 V(p-p)/75 Ω

S-video: DVR, VCR, MONITOR OUT:

Y (luminance): 1 V(p-p)/75 ΩC (chrominance, burst): 0.286 V(p-p)/75 Ω

Component: MONITOR OUT:

Y (luminance): 1 V(p-p)/75 ΩPB, PR: 0.7 V(p-p)/75 Ω

Synchronization: Negative

FM tuner (IHF)Tuning Range: 87.5 MHz to 108.0 MHz

Usable Sensitivity:

Monaural: 12.8 dBf (1.2 µV/75 Ω)

50 dB Quieting Sensitivity:

Monaural: 16.0 dBf (1.7 µV/75 Ω)

Stereo: 37.5 dBf (20.5 µV/75 Ω)

Stereo Separation at REC OUT: 35 dB at 1 kHz

AM tunerTuning Range: 530 kHz to 1 710 kHz

GeneralPower Requirements: AC 120 V , 60 Hz

Power Consumption: 120 W/160 VA (at operation)

2 W (in standby mode)

Dimensions (W x H x D): 435 mm x 70 mm x 329.5 mm

(17 3/16 inches x 2 13/16 inches x 13 inches)

Mass: 6.3 kg (13.9 lbs)

39-40RX-F10S[J]_f.p65 04.4.22, 15:2640

THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA ANDIN COMMONWEALTH OF PUERTO RICO.

WHAT WE WILL DO:If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner.Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized servicecenters. Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and partsthereof may be brought to a JVC authorized service center on a carry-in basis except for Television sets having a screensize 25 inches and above which are covered on an in-home basis.

WHAT YOU MUST DO FOR WARRANTY SERVICE:Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorizedservice center, please call toll free: (800) 537-5722.

If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, witha copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, thename and location of which will be given to you by the toll-free number.

If you have any questions concerning your JVC Product, please contact our Customer Relations Department.

WHAT IS NOT COVERED:This limited warranty provided by JVC does not cover:1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty

installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized byJVC to render such service, or if affixed to any attachment not provided with the products, or if the model numberor serial number has been altered, tampered with, defaced or removed;

2. Initial installation and installation and removal for repair;3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning;4. Damage that occurs in shipment, due to act of God, and cosmetic damage;5. Signal reception problems and failures due to line power surge;6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;7. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);

There are no express warranties except as listed above.

THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, ISLIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.

JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHERDAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGETO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACHOF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANT-ABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.

Some states do not allow the exclusion of incidental or consequential damages or limitations on how long animplied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specificlegal rights and you may also have other rights which vary from state to state.

LIMITED WARRANTYJVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THEORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the dateof original retail purchase for the period as shown below. ("The Warranty Period")

PARTS LABOR2 YRS 2 YRS

JVC COMPANY OF AMERICA

DIVISION OF JVC AMERICAS CORP.1700 Valley RoadWayne, NJ 07470

REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OFREFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATIONPACKAGED WITH EACH REFURBISHED PRODUCT.

For customer use:

Enter below the Model No. which is located either on the rear, bottom or side of the cabinet. Retain this informationfor future reference.

Model No. : Serial No. :

Purchase data : Name of dealer :

AUDIO-2

warrant_RX-F10S[J]_f.p65 04.4.22, 15:452

BT-51002-5(0301)

QUALITY SERVICE

HOW TO LOCATE YOUR JVC SERVICE CENTER

Dear Customer,In order to receive the most satisfaction from your purchase,please read the instruction booklet beforeoperating the unit.In the event that repairs are necessary, please call 1 (800)537-5722 for your nearestauthorized servicer or visit our website at www.JVC.com

Remember to retain your Bill of Sale for Warranty Service.

Do not service the television yourself

Caution

To prevent electrical shock,do not open the cabinet.There are no user serviceableparts inside.Please refer to qualified service personnel for repairs.

Accessories

To purchase accessories for your JVC product,please call toll free:1 (800)882-2345 oron the web at www.JVC.com

TOLL FREE: 1 (800) 537-5722

http://www.jvc.com

Authorized Service Centers

®

warrant_RX-F10S[J]_f.p65 04.4.22, 15:453

VICTOR COMPANY OF JAPAN, LIMITED

0404MWMMDWJEIN

EN

© 2004 VICTOR COMPANY OF JAPAN, LIMITED

HO

ME

TH

EA

TE

R R

EC

EIV

ER

RX

-F10S

cover_RX-F10S[J]_f.p65 04.4.22, 15:262

Documents

HOME THEATER RECEIVER RX-F10S - JVC USAresources.jvc.com/Resources/00/00/93/LVT1163-001A.pdf · LVT1163-001A [J] RX-F10S HOME THEATER RECEIVER INSTRUCTIONS For Customer Use: Enter