Ireland Taiwan Rd, Zhongli City, Taoyuan County, 32064 ......• Security (Alarms, tracking, remote monitoring) e.g. security camera manufacturers about Taoglas our products and services

Taoglas Catalogue | 1

Taog

lasTaoglas

IrelandUnit 7 Peare Campus, Moyne Business Park, Old Dublin Road, Enniscorthy, Co. Wexford, Ireland

Phone: +353 53 9169500Fax: +353 53 9169655Email: [email protected]

TaiwanNo 25, Changchun 6th Rd, Zhongli City, Taoyuan County, 32064, Taiwan, ROC320 桃園縣中壢市長春六路 25號


USA8375 Camino Santa Fe, Suite A, San Diego, CA 92121 USA

Phone: +1 858 450 0888Email: [email protected]

MexicoMX S DE RL DE CV, Calle del Olivo 17202-14, Col, Rinconada Otay, Tijuana , B.C, 22457, México


ISO 9001:2008 certified

Taoglas Catalogue2 |

Welcome to the Taoglas Catalogue 2012

Taoglas Limited reserves all rights to this document and the information contained herein.

Products, names, logos, images and designs described may in whole or in part be subject to intellectual property rights.

Data shown in this document are estimates only and do not constitute a warranty of guarantee of product performance or services.

No warranty of any kind, either expressed or implied, is made in relation to the accuracy, reliability, fitness for a particular purpose or content of this document.

This document may be revised by Taoglas Limited at any time.

For most recent information please check product data on our website: www.taoglas.com.


Taoglas 4About Taoglas 4Applications 4What Taoglas can offer you? 8Contact Details 9

Cellular 2g/3g/4g 10On Board Cellular Antenna Solutions (SMT) 10Embedded Cellular Flexible Series (with Cable & Connector) 11Embedded Cellular Rigid Series (with Cable & Connector) 12Industrial External Cellular Screw Mount Antennas 13Industrial External Cellular Whip Antennas 14Automotive External TS16949 First Tier Approved 15Cellular Terminal Mount Series 16LTE Antenna Solutions 17WiMAX Antenna Solutions 19

GPS - GlonaSS - GnSS 20GPS External Antenna Solutions 20GPS Active Embedded Antenna Modules 22GPS Embedded SMT Solutions 26GPS Embedded PIN patches 28GPS Loop Antennas 31GPS-GLONASS External Solutions 32GPS-GLONASS Active Embedded Series 33GPS-GLONASS Passive Antennas 34

Combination – Choose between GPS/ GnSS/ Cellular/ Wi-Fi/ ISM 36Automotive/ Industrial Screw-Mount - Smallest compact - Hercules series - 2in1 36Automotive/ Industrial Screw-Mount - Low profile – Spartan series - 3in1 37Automotive/ Industrial Screw-Mount - RF professional – Pantheon series - 3in1, 4in1 39Automotive Interior Mount - Automotive Glass/Covert Mount - Stingray Series - 2in1 40Automotive Interior Mount - Automotive Glass/Covert Mount - Stream Series - 2in1 41

ISM (135/ 169/ 433/ 450/ 724/ 868/ 915 MHz) 42Automotive/ Industrial Screw-Mount -Smallest compact – Hercules Series 42Omni-directional Fiberglass Series – Barracuda Series 43Terminal Mount Range 44Embedded ISM Flexible Series (with Cable & Connector) 48Embedded ISM Rigid Series (with Cable & Connector) 49On Board ISM Antenna Solutions (SMT) 50Ceiling Mount ISM Solution - Crusader 51

WiFi/zigBee/Public Safety 522.4GHz Automotive/ Industrial Screw-Mount -Smallest compact 522.4GHz Antenna Solutions Embedded 532.4GHz Antenna Solutions Embedded (Cable & Connector) 552.4GHz/5GHz Dual Band Antenna Solutions – Embedded SMT 572.4GHz/5GHz Dual Band Flexible Antennas (Cable & Connector) 582.4GHz/5GHz External (Terminal Mount) 592.4Ghz/5Ghz Antenna Solutions External 612.4GHz MIMO Antenna 62

Satellite Communications 64Iridium Embedded Solutions 64Iridium External Solutions 65Iridium-GPS Embedded Antenna 66

accessories 68Cable Assemblies 68Receptacles 69On Board Connectors 70

Services 72Service Packages 72









Taoglas


about Taoglasour Company

Taoglas is an international company with a 100% positive approach and a world-class way of doing things. We listen, we learn, we respond.

Since our foundation in 2004, we’ve combined forward-focused technological thinking with a

determination to understand and respond to the real needs of our customers.

Our cross-cultural business-solutions approach means research, design and customer support services are based at our world-class technology centres in Ireland, the US and Taiwan.

Today Taoglas provides a comprehensive range of external, embedded and base station antenna

solutions for M2M applications such as Telematics / Automotive, Smart-Grid, Metering / Telemetry, Home Automation, Remote Monitoring and Medical applications.

We are committed to continually researching new materials and improved antenna designs. Our surface-mount antenna range and flexible embedded products are unique in the industry.

Taoglas works with you to enable your company achieve the best possible performance from your wireless devices. We can custom-design to suit your

individual needs or provide highly- economical off-the-shelf solutions.

Our step-by-step design process ensures your devices achieve target specifications and comply with all required approvals so they’re ‘right first time’. If you’re looking for a pioneering approach to problem-solving, talk to us at Taoglas. In the field of M2M, we outperform the rest.

‘Taoglas shows a real willingness to solve problems, I value this’

Client Comment


Taog

las


about Taoglasour Market

Our customers deliver innovation and value into;

• Transportation, Supply Chain & Logistics (delivery routes, vehicle diagnostics and engine optimization, accident prevention) e.g. fleet management companies

• Healthcare (Monitoring at home, remote care, pill dispensers, equipment tracking, hospital system equipment inventory management) e.g. Medical Device companies

• Smart Grid (Wireless utility meter reading, utility asset management, fault detection, energy management devices and remote power management) e.g. Meter manufacturers

• Automotive (Pay as You Drive Insurance, Vehicle Tracking, Connected Navigation, Ecall, Internet) e.g. telematics hardware providers

• Retail (Digital Signage, POS systems, inventory tracking) e.g. hand-held card payment system providers

• Industrial (Sensors, Oil exploration, field communications, fault detection) e.g. electronic control device manufacturers

• Security (Alarms, tracking, remote monitoring) e.g. security camera manufacturers

about Taoglasour products and services

We work with the top innovators in M2M that are tasked to deliver smarter and/or better performing systems for wireless applications.

As well as a wide range of off the shelf antenna solutions (embedded and external) Taoglas has grown with the market and now offers a suite of related services;

• Custom Antenna Design

• Device layout optimization

• Noise Control

• Certification (e.g. PTCRB) Pre-testing

• Over the Air TRP/TIS Optimization to pass carrier / network requirements

• First Tier Automotive approved antennas produced at TS16949 facility using PPAP and IMDS

• Global Coverage with full test labs in USA, Taiwan, Ireland


Taog

lasTaoglas


applications

Automotive Transportation

AftermarketTracking

Black box Video

External

GPS AA.105 - Titan, Magnetic Mount, High Gain (30dB) 20

Cellular G.21 - Penta-Band Hercules Screw-Mount 13

2.4/ 5 GHzWS.01.B - Hercules Screw- Mount 52

WA.500w - Stingray Adhesive 61

915 MHz IS.05.B - Hercules Screw-Mount 42

Combination

MA.203 - Stingray, GPS/Cellular Adhesive-Puck 40

MA.104 - GPS/Cellular Screw-Hercules 36

MA.301 - Stingray Magnetic-Puck 40

MA.501.C - GPS/Wi-Fi Screw-Hercules 36

MA.600 - Spartan Series 3in1 Screw-Mount - Low Profile 37

MA.603 - Spartan Screw Mount 38

InternalGPS

SGP.25 - GPS Embedded SMT Solutions, 25mm Patch 27

AP.25F - 2 Stage 28dB 25m Patch, Front End SAW Filter 24

CellularPA.25 - Hexa-Band Cellular Ceramic PIFA 10

FXP.14 - Hepta-Band Cellular, 1575MHz GPS Flexible Polymer 11

First-tier OEM

TrackingBlack box

Video

ExternalGPS AA.108 - Titan Adhesive Mount 20

Cellular GSA.8821 - Penta-Band, Hercules Screw-Mount 15

Combination MA.203 - GPS/Cellular Adhesive-Puck 40

InternalGPS

SGP.25 - GPS Embedded SMT Solutions, 25mm Patch 27

AP.25F - 2 Stage 28dB, 25m Patch, Front End SAW Filter 24

Cellular PA.25 - Hexa-Band Cellular Ceramic PIFA 10

FXP.14 - Hepta-Band Cellular, 1575MHz GPS Flexible Polymer 11

1. automotive/Transportation

Below is a list of common applications where our antennas are used, and a recommendation of our most popular and high performance solutions for each application.

page


Taog

lasTaoglas


ElectricGas

Water

External

CellularG.21.B - Penta-Band Hercules Screw-Mount 13

FW.90 - Penta-Band Flexible Inner Steel Core Monopole Whip 14

ISM 433 IS.01.B - Hercules Series, 433MHz, Screw-Mount 42

ISM 868IS.04.B - 868MHz, Screw-Mount 42OMB.868 - 868MHz Omni-Directional Dipole Antenna 43

ISM 915 IS.05.B - 915MHz Screw-Mount 42

2.4/5GHz WS.01 - 2.4GHz/5.2GHz Hercules Screw- Mount 52

GPSA.01.C - Hercules Screw Mount 21

A.03.B - Hercules Screw Mount 21

Combination

MA.104 - GPS/Cellular Screw-Hercules 36

MA.501 - GPS/Wi-Fi Screw-Hercules 36

MA.600 - Spartan Series 3in1, Screw-Mount 37

MA.603 - Spartan Screw-Mount 38

CellularFXP.14 - Hepta-Band Cellular 1575MHz GPS Flexible Polymer 11

Internal

PA.25 - Hexa-Band Cellular Ceramic PIFA 10

ISM 433 FXP240 - Embedded ISM Flexible Series (with Cable & Connector) 47



ISM 868FXP280 - ISM Embedded Flexible Circuit (with Cable & Connector) 48

ILA.02 - On Board ISM antenna Solutions (SMT) - 868Mhz 50

ISM 915FXP290 - ISM Embedded Flexible Circuit (with Cable & Connector) 48

ILA.01 - On Board ISM antenna Solutions (SMT) 50

2.4 GHz

WLP.25 - 2.4GHz Ceramic Patch 53

SWLP.12 - 2.4GHz, SMT Ceramic Patch 54

FXP.72 - Freedom 2.4GHz Ground Coupling 55

FXP.73 - Blue Diamond 2.4GHz 56

WLA.01 - 2.4GHz Ceramic PIFA 53

ISM dual-band 2.4/5 GHz

FXP.810 - Dual-Band 2.4GHz 4.9-6.0Ghz 58

FXP.830 - Dual-Band 2.4GHz 4.9-6.0Ghz 58

2. Smart Metering

applications

HandsetsTablets

IndustrialConsumer

DefenceInternal

Cellular FXP.14 - Hepta-Band Cellular 1575MHz GPS Flexible Polymer 11


2.4 GHz FXP.73 - Blue Diamond 2.4GHz 56


SWLP.12 - 2.4GHz SMT Ceramic Patch 54

2.4/ 5 GHz FXP.831 - Dual-Band 2.4GHz 4.9-6.0Ghz 58

SDWA.01 - Dual-Band 2.4GHz 4.9-5.8Ghz Ceramic SMT Antenna 57

GPS ALA.01 - 1 Stage 16dB Front End SAW Filter 31

Medical Internal

Cellular FXP.14 - Hepta-Band Cellular 1575MHz GPS Flexible Polymer 11


2.4 GHz FXP.73 - Blue Diamond 2.4GHz 56


SWLP.12 - 2.4GHz SMT Ceramic Patch 54

2.4/ 5 GHz FXP.831 - Dual-Band 2.4GHz 4.9-6.0Ghz 58

SDWA - Dual-Band 2.4GHz 4.9-5.8Ghz Ceramic SMT Antenna 57

GPS ALA.01 - 1 Stage 16dB Front End SAW Filter 31

3. Industrial Handsets/Tablets

page

page


Taog

lasTaoglas


Director Dermot o’Shea in the Taoglas ETS 12M

400MHz to 6GHz 3D oTa Test Chamber, Ireland

What can Taoglas offer you? The Taoglas advantage

1. MaterialsWe are not committed to one material technology. We use a wide variety of materials and are constantly researching the latest developments. We ship antennas made from high grade Ceramics, FR4, Metal, Fiberglass, PTFE, Mylar and flexible PCB.

2. Surface Mount TechnologyTaoglas are the worldwide leaders of high performance surface mounted antenna solutions for M2M with unique (patent pending) products for cellular, GPS, Wi-Fi and other ISM band antennas. These products are delivered on tape and reel and connect to our customers devices during the standard reflow process.

We are the first in the market to provide automotive approved SMT GPS patch antenna products and also a very unique multiband cellular PA25a antenna that achieves high performance off the shelf in a small area.

3. Antenna Design TechniquesWe select the antenna design that is right for the individual project, application or market; PIFA antennas, Monopoles, Dipoles, Loop Antennas etc. We are not limited by design methodol-ogy, we use software and practical tried and tested procedures to deliver the most effective and efficient antenna.

This means we are also not limited by antenna frequency we have the ability to deliver all antennas for the project.

For the device itself you may need to have multiple antenna types GPS,multi band cellular,diversity, Wi-Fi, Bluetooth, RFID etc. It is best to have one antenna company provide all the anten-nas because it cuts development time by half while also availing of bulk buying discounts.

We can design and deliver an antenna at any frequency and we have a huge amount of experience in being challenged to design with small spaces

and high target specifications. This means we can work to provide the full antenna solution for a wireless network base station antennas,device antennas and remote antennas for the hard to reach connections. 4. M2M FocusedTaoglas employees have built up years of practical international experience in different markets, and have worked on thousands of custom M2M devices.

Simply put, we know what designs work and what do not. We also stay close to M2M module developments and tradeshows so we can keep our product line as close as possible to ever changing market demands.

We work with the leading certified test labs so we are fully aware of wireless device approvals and test methods.

5. The Taoglas promiseTaoglas antennas are tested in the industry’s most advanced CTIA approved test chambers, the very same ones that the world’s automobile, mobile phone and notebook companies use to qualify the RF performance of their antennas.

Unlike other antenna companies we show the real test results and conditions they were tested in. Antenna performance will change if any parameter of the antenna or environment is changed.

For omni-directional antennas the average gain over 360 degrees, also

known as efficiency, is the only proper indicator of antenna performance. A single peak gain figure used by most of our competitors are not indicative of real performance for omni-directional an-tennas as they only give the gain at one particular angle or plane and mounting condition for one frequency point only.

You will often see antennas with peak gain of 2dBi listed, however this is largely meaningless as the average gain will be much lower, and it is average gain that influences the power and sensitivity of your product, not the peak gain.

In contrast Taoglas antenna specifica-tions show average gain, efficiency and peak gain across the whole frequency band. Changing a cable type, length, will also change the gain of any antenna. We are committed to being honest and open in our specifications.

It is recommended never to rely on an antenna specification as a guarantee of antenna performance. It is advised to try different antennas in real life test conditions, or ask a Taoglas representa-tive and we will gladly test our antenna with your product and compare to a competitor’s antenna in your product to get the real test results.

6. Your TOTAL antenna and RF solution for wirelessPlease contact us today to discuss your wireless communication requirements or see how we can help you be more com-petitive in your market. Avail of our test and design service packages at our fully qualified OTA test facilities in Wexford, Ireland and San Diego, USA.


Taog

lasTaoglas


Contact Details

Feel free to contact our co-founders and Joint Managing Directors directly anytime.

Visit our website: www.taoglas.com Contact us: [email protected]

Dermot o’Shea Ronan Quinlan

IrelandTaoglas Ltd. Unit 7 Peare Campus, Old Dublin Road,Moyne Business Park Enniscorthy, Co. Wexford, Ireland

Phone: +353 53 9169500 Fax: +353 53 9169655 Email: [email protected]

TaiwanTaoglas Limited No 25, Changchun 6th Rd, Zhongli City, Taoyuan County, 32064, Taiwan, ROC

Phone: +886 3 4612001 Fax: +886 3 4612011 Email: [email protected]

USaTaoglas USA, Inc. 8375 Camino Santa Fe,Suite A, San Diego, CA 92121, USA

Phone: +1 858 450 0888 Email: [email protected]

MexicoTaoglas MX S DE RL DE CV, Calle del Olivo 17202-14, Col, Rinconada Otay, Tijuana, B.C, 22457, México


USaTaoglas USA, Inc.

IrelandTaoglas Ltd.

TaiwanTaoglas Limited

Cellular 2g/3g/4g10 |

Cel

lula

rCellular

on Board Cellular antenna Solutions (SMT)Embedded Cellular SMT Mount Range

The patent pending PA.700 2G/3G/4G 700MHz to 960MHz, 1710 to 2200MHz high efficiency antenna is the latest SMT solution.

These antennas have wide bandwidths over a small area, while also achieving high

efficiency and awesome TRP/TIS results due to very little transmission losses. These ceramic antennas are dense and robust and pass drop tests easily; they pass 20G automotive vibration testing and are used worldwide by large global vehicle brands.

The benefits for production are also clear as they are delivered on tape and reel, and soldered onto the board during the reflow process. This gives you automated assembly, robustness and uniform performance from every device.

Model no

PA.22ATri-Band CellularCeramic PIFA

Electrical Data

Working Freq. 880~960MHz1710~1990MHz

VSWR: 2.5 Max*.Polarization LinearImpedance 50ΩReturn loss ≤-10dBEfficiency 30% average.

Mechanical Data

GP Size 35*115mmDimensions 29.8*6*5mmoperating Temp. -40°C~+85°CTermination Ag (Pb Free)

Model no

PA.25AHexa-Band CellularCeramic PIFA

Electrical Data

Working Freq. 824~960MHz1700~2170MHz

VSWR: 3.0 Max.*Polarization LinearImpedance 50ΩReturn loss ≤-10dBEfficiency 50% average.

Mechanical Data

GP Size 40*95mmDimensions 35*6*5mmoperating Temp. -40°C~+85°CTermination Ag (Pb Free)

Model no

PA.700Septa-BandLTE/Cellular/CDMACeramic PIFA

Electrical Data

Working Freq. 689~960MHz1710MHz to 2170MHz

VSWR: 3.0 MaxPolarization LinearImpedance 50ΩReturn loss ≤-16dBEfficiency ≥ 56%

Mechanical Data


Our custom metal stamp PIFA and monopole antenna range offers the highest efficiency for small form factor applications where ground is small or where there is no room for a ceramic solution.

These antennas are 100% customised for each design so will suit high volume or critical applications.

Taoglas’ unique ceramic multiband cellular antennas use high grade ceramics which have been developed through years of expertise in delivering the right materials for high performance antennas.

*VSWR depends on the environment

Cellular SMT Mount Metal PIFa Range

Example of a Metal Stamp Solution

Cellular 2g/3g/4g | 11

Cel

lula

rCellular

Embedded Cellular Flexible Series (with Cable & Connector)Flexible Polymer PCB antennas

Flexible circuit antennas have been used in many modern mobile phone antenna designs.

Taoglas uniquely supplies flexible circuit antenna solutions for the M2M market. The material performs very well at higher frequencies like GSM and 3G etc.

The products from this range are used for M2M modules that come with a connector - or where there is no space on the device PCB for a cellular antenna. The antenna can be stuck directly to the device housing by pulling off the 3M label and using the automotive grade 3M glue that is on one side of the antenna.

Despite the extremely thin material the antennas are very robust and pass the required device temperature and vibration/shock tests.

They come in a range of shapes and sizes.Cable and connectors are fully customizable; IPEX MHF (U.FL compatible) and MMCX are standard.

The FXP.14 is a ground-plane independent antenna which saves on space, making it suitable for even smaller sized M2M devices in tracking, navigation, automotive and telemedical markets. The ground is designed into the antenna.

Model no

FLA.01Penta-BandLoop Antenna

Electrical Data

Working Freq. 850/900/1800/1900/2100MHz

Peak Gain 3dBiPolarization LinearImpedance 50ΩReturn loss ≤ -9dBEfficiency > 30% w/GND

Mechanical Data

Dimensions 66*37*0.8mmoperating Temp. -40°C~+85°CCable (Std)* 45mm Ø 1.13Connector (Std)* IPEX U.FL compMaterial Flex Polymeradhesive Tape 3M 467

* Cables and Connectors are Customizable.

Model no

FXP14Hepta-Band Cellular1575MHz GPSFlexible PolymerAntennaGround plane independent

Electrical Data

Working Freq. 850/900/1700/1800/1900/2100 Mhz1575.42MHz GPS

Peak Gain 3dBiPolarization LinearImpedance 50ΩReturn loss ≤ -17dBEfficiency > 50%

Mechanical Data

Dimensions 35*6*5mmoperating Temp. -40°C~+85°CCable (Std)* 100mm Ø 1.13Connector (Std)* IPEX U.FL compMaterial Flex Polymeradhesive Tape 3M 467

Model no

FXP07Penta-BandCellular FlexiblePolymer Antenna

Electrical Data

Working Freq. 850/900/1800/1900/2100MHz

Polarization LinearImpedance 50ΩReturn loss ≤-9 avg.Efficiency > 30% w/ GND

≤ 30% without GND

Mechanical Data

Dimensions 41*24*0.1mmoperating Temp. -40°C~+85°CCable (Std)* 100mm Ø 1.13Connector (Std)* IPEX MHF U.FL compMaterial Flex Polymeradhesive Tape 3M 467


Cel

lula

rCellular

Embedded Cellular Rigid Series (Cable & Connector)PC Series - Rigid Cellular antennas

Model no

PC27Quad-Band CellularFR4 PCB Antenna

Electrical Data

Working Freq. 850/900/1800/1900MHz

Radiation Pattern OmniPolarization LinearImpedance 50ΩReturn loss ≤-14dBEfficiency 25% avg.

Mechanical Data

Dimensions 34*7*0.8mmoperating Temp. -40°C~+85°CCable (Std)* 100mm ø 1.13Connector (Std)* IPEX U.FL compMaterial FR4

Model no

PC30Penta-Band CellularFR4 PCB Antenna

Electrical Data

Working Freq. 850/900/1800/1900/2100MHz

Radiation OmniPolarization LinearImpedance 50ΩReturn loss ≤-4dBEfficiency 50% avg.

Mechanical Data


Model no

PA.24Tri-Band Cellular PIFAon PCB with cable and connector

Electrical Data

Working Freq. 900/1800/1900MHz

Radiation OmniPolarization LinearImpedance 50ΩReturn loss ≤-10dBEfficiency 50% avg.

Mechanical Data

Dimensions 35*15*7mmoperating Temp. -40°C~+85°CCable (Std)* 100mm ø 1.13Connector (Std)* IPEX U.FL compMaterial Ceramic AG (Pb Free)


Taoglas is the M2M market leader for embedded cellular antenna solutions.

They come in a range of shapes, sizes and materials (FR4/Flex Circuit). Cable and connector are fully customizable; IPEX MHF (U.FL compatible) and MMCX are standard.

The antennas can be fixed into plastic slots in a device plastic housing, or backing adhesive can be supplied for affixing to the device plastic housing or holes made in the

antenna for screw-fixing.

The PC series are ground-plane independent antennas which save on space, making them suitable for even smaller sized M2M devices in tracking, navigation, automotive and telemedical markets.

Ground is designed into the antenna. Custom antennas can be designed and tuned for devices.

The products from this PC range are used for M2M modules that come with a connector - or where there is no space on the device PCB for a cellular antenna.


Cel

lula

rCellular

Industrial External Cellular Screw Mount antennasCellular antenna External Range Cable and Connector

The Hercules G.21, is a waterproof, high performance Penta-band Cellular (GSM/CDMA/PCS/DCS/UMTS/WCDMA/HSDPA) antenna designed as an ideal solution for AVL or fleet management applications and works worldwide. Hercules has been designed for heavy duty applications in outdoor environments.

It features extra thick threads and strong washers for sturdy installation. Its outer casing is manufactured from durable UV resistant ABS, protecting it from vandalism and direct attack. It also features conve-nient side slots so that the antenna cables can run easily from the side.

Its design came from Market Research in the field. Its new low profile look has been designed to not catch on tree-branches. It can also be mounted on metal structures.Its the smallest high performance antenna in the market.

Model no

G.21.BPenta-BandHerculesScrew-Mount

Electrical Data

Working Freq. 850/900/1800/1900/2100MHz

Gain 2dBi avg.Radiation Pattern Omni-DirectionalPolarization LinearImpedance 50ΩReturn loss -15dB avg.Efficiency > 40% avg.

Mechanical Data

Dimensions 52*29mm (2.05”*1.14”)operating Temp. -40°C~+85°CCable (Std)* 3M Rg-174Connector (Std)* SMA(M)Mounting ScrewIP Rating IP69

The new Generation Hercules (Gen II) is a high performance steel thread-mount penta-band cellular antenna for external use on vehicles and outdoor assets worldwide. omni-directional high gain across all bands ensures constant reception and transmission.


Cel

lula

rCellular

Industrial External Cellular Whip/Wall Mount antennasCyclops Cellular solution for Industrial applications

The WM.90 wall mount flexible whip monopole has unique exceptional wide-band peak gain characteristics to maintain the highest possible performance on all common 2G/3G bands used worldwide.

This antenna delivers wider coverage areas and more reliable connections for professional customers in the automotive, industrial industries. The whip is made up of a flexible inner steel core covered by TPU so extremely resistant to collisions and maintaining its original shape and RF performance. The whip and the connection

internally to the bracket is completely IP67 waterproof.

The bracket allows complete concealment of the cable for a more secure integration and cleaner installation. The cable can also be routed out of the back wall of the bracket into the interior of the mounting wall

for added security against vandalism. The cable and connector can be completely customized, the whip itself can also be changed for different frequency bands or gain requirements.

Other connection versions of the Whip are in development.

Model no

WM.90Wall Mount High GainFW.90 on IntegratedL Bracket

Electrical Data

Working Freq. 850/900/1800/1900/2100MHz

Gain 2.8~4.0dBiRadiation Pattern Omni-DirectionalPolarization LinearImpedance 50ΩReturn loss ≤-20dB avg.Efficiency 59~69%

Mechanical Data

Dimensions 368mm HighBracket

operating Temp. -40°C~+85°CCable (Std)* CFD-200Connector (Std)* SMA(M)Mounting Wall Mount L BracketIP Rating IP67

Model no

FW.90Penta-BandFlexible InnerSteel CoreMonopole Whip

Electrical Data

Working Freq. 850/900/1800/1900/2100MHz

Gain -0.7~2.5dBiRadiation Pattern Omni-DirectionalPolarization LinearImpedance 50ΩReturn loss ≤-18dB avg.Efficiency 27~62%

Mechanical Data

Dimensions 250mm Highø 16mm

operating Temp. -40°C~+85°CConnector (Std)* SMA(M)Mounting Screw MountIP Rating IP67

Model no

GA.107Penta-BandWhip AntennaMagnetic Mount

Electrical Data

Working Freq. 850/900/1800/1900/2100MHz

Gain 2dBi Typ.Radiation Pattern Omni-DirectionalPolarization LinearImpedance 50ΩReturn loss ≤-15dB avg.Efficiency > 30% avg.

Mechanical Data

Dimensions 120mm HighØ 29.5mm

operating Temp. -40°C~+85°CCable (Std)* 3M Rg-174Connector (Std)* SMA(M)Mounting MagneticIP Rating IP65


Cel

lula

rCellular

automotive External TS16949 First Tier approved I-Bar First Tier automotive approved adhesive Cellular solution

our adhesive mount external antennas offer ease of installation, high performance in compact form factors. They are supplied with high quality durable 3m tape to allow secure fixing onto any surface.

The GSA.8821 I-Bar Penta-band GSM Antenna is flexible and robust. Its slim-line design allows for covert and convenient installation in automotive vehicles, its Omni-directional gain across all bands ensures constant reception and transmission. It is

a high gain, high efficiency solution which complies with AT&T standards for high efficiency antennas.

The GSA.8821 is manufactured and tested in a TS16949 first tier automotive approved

facility and the part GSA.8821.301721 (with Fakra Code D connectors) is listed in the global automotive IMDS databases, it has gone through full PPAP design, reliability and quality audits, including audits at the production facility.

Model no

GSA.8821.BPenta-BandI-Bar AdhesiveAdhesive

Electrical Data

Working Freq. 850/900/1800/1900/2100MHz

Gain 3.3dBi avg.Radiation Pattern Omni-DirectionalPolarization LinearImpedance 50ΩReturn loss ≤-12dB avg.Efficiency > 57% avg.

On non metal

Mechanical Data

Dimensions 107*15*6mmoperating Temp. -40°C~+85°CCable (Std)* 3M Rg-174Connector (Std)* SMA(M)Mounting AdhesiveIP Rating IP65


Cel

lula

rCellular

Cellular External (Terminal Mount)Cellular Range Terminal (Connector) Mount antennas

They are designed for simple screw on SMA connection to cellular terminals and cellular equipment.

The TG.09 Penta-band Cellular Hinged Rotatable SMA antenna is a high efficiency monopole antenna. Compared to other much larger antennas on the market, it has superior wide-band high efficiency characteristics. This antenna is used by many of the leading wireless device providers in the

world marketplace.There are fixed 90 degree, fixed straight connector and hinged versions available.

The Taoglas solutions incorporate a carefully designed and optimized robust solution for these products. The antenna inside is optimized and tuned for its housing and connector, giving your device maximum sensitivity.

Terminal antennas are the best choice for external cellular as they eliminate cable loss and different performances associated with antennas supplied with cables.

*Also available with Reverse Polarity Connectors

Model no

TG.22 (R/A)Penta-Band CellularTerminal Antenna

Electrical Data

Working Freq. 850/900/1800/1900/2100MHz

Radiation Pattern Omni-DirectionalPolarization LinearImpedance 50ΩReturn loss -8.8dB avg.Efficiency > 27%

(Ground-plane dependent)

Mechanical Data

Dimensions 45*16.4*7.8mmoperating Temp. -40°C~+85°CConnector (Std)* SMA(M) R/A*Mount R/A

available in black and white

Model no

TG.22 (Straight)Penta-Band CellularTerminal Antenna

Electrical Data

Working Freq. 850/900/1800/1900/2100MHz


(Ground-plane dependent)

Mechanical Data

Dimensions 48*7.8mmoperating Temp. -40°C~+85°CConnector (Std)* SMA(M)*Mount Straight


Model no

TG.09Penta-Band CellularRotatable Hinge

Electrical Data

Working Freq. 850/900/1800/1900/2100MHz


(on edge PCB)

Mechanical Data

Dimensions 72mm (Height)Ø 9.8mm

operating Temp. -40°C~+85°CConnector (Std)* SMA(M)Mount Hinged



Cel

lula

rCellular

lTE antenna SolutionsUltra wideband, Fourth Generation, (4G) network antenna range

Taoglas has launched a range of high efficiency antennas for the emerging lTE system using unique ultra wideband antenna design techniques.

Model no

MA.700Screw-Mount

GPS2 Stage 32dB LNA

Electrical Data

Frequency 1575.42±2MHzGain 4.0dBic typ.@ Zenithave. Efficiency 50%Polarization RHCPImpedance 50ΩVSWR ≤1.92

Mechanical Data

Dimensions H:85.73mmØ 145.59mm

Mounting Thread Ø 30mmoperating Temp. -40°C~+85°CCable* 3M RG-174Connector* SMA(M)IP Rating IP67

LTE/CellularWide-Band700-2170MHz

Electrical Data

Frequency Penta-band 850/900/1800/1900/2100MHz

Gain 2dBi avg.ave. Efficiency 50%Polarization VerticalImpedance 50ΩVSWR ≤3.0

Mechanical Data


Mounting Thread Ø 30mmoperating Temp. -40°C~+85°CCable* 3M Low-loss CFD-200Connector* SMA(M)IP Rating IP67

Wi-Fi

Electrical Data

Frequency 2.4~2.5GHz4.7~5.9GHz

ave. Efficiency 55.5%Polarization VerticalImpedance 50ΩVSWR ≤1.92

Mechanical Data




Cel

lula

rCellular

lTE antenna SolutionsUltra wideband, Fourth Generation, (4G) network antenna range

Taoglas has launched a high efficiency antenna for the emerging LTE system using unique ultra wideband antenna design techniques.

The antenna allows designers to start testing and developing LTE devices with

antennas designed to operate efficiently in the bands of interest.

We have used years of cellular antenna design experience to predict the require-ments of these new designs for emerging networks.

This design can be optimized and/or customized for any 4G device. Onboard solutions of the flexible circuit antennas are also available.

Model no

FXP400LTEEmbedded Flex Adhesive Mount

Electrical Data

Working Freq. 690-940MHz&1720-3130 MHz

Gain 4.0-5.0dBi PeakRadiation Pattern Omni-DirectionalPolarization LinearImpedance 50ΩReturn loss ≤-10dBEfficiency >70%

Mechanical Data

Dimensions 100*38*0.1mmoperating Temp. -40°C~+85°CCable (Std)* 100mm coax Ø 1.13Connector (Std)* IPEX MHFI (U.FL)Mounting 3M 467MP Type

Model no

PA.700Septa-BandLTE/Cellular/CDMACeramic PIFA

Electrical Data

Working Freq. 689~960MHz1710MHz to 2170MHz

VSWR: 3.0 MaxPolarization LinearImpedance 50ΩReturn loss ≤-16dBEfficiency ≥ 56%

Mechanical Data



Cel

lula

rCellular

WiMaX antenna SolutionsWiMaX end-to end solutions for Mesh area networks

The FXP100 flexible wideband WiMaX(2100-4320MHz) antenna has been developed from years of cellular antenna design experience, the range delivers the increased bandwidth required for WiMaX without performance compromise.

With high efficiency (>60%) in a small size, the antenna is highly reliable.

The Flexible Polymer allows the antenna to be fitted to curved surfaces, and its ease

of integration is further optimized by its rectangular shape.

Model no

FXP.100Flex WiMAXPCB Antenna

Electrical Data

Frequency 2100-4320MHzGain 2dBi avg.out. Impedance 50ΩPolarization LinearRadiation Omni-DirectionalReturn loss ≤-10dBop. Temp. -40°C~+85°C

Mounting Data

Dimensions 31*24*0.2mmConnector IPEX MHF(U.FL)Cable 150mm Ø 1.13Mounting 3M 467 Tape

GPS - GlonaSS - GnSS20 |

GP

S -

GLO

nA

SS

- G

nSS

GP

S - GLO

nA

SS - G

nSS

GPS External antenna SolutionsGPS External antenna Range

External antennas deliver the best possible performance for any product or device. This range is ideal for high performance, robust, covert installations where durability is paramount.

Magnetic, adhesive and screw mount options are available. Where the communication unit is placed in an area of no, or poor, GPS signal, an external antenna is the obvious choice.

The Titan AA.108 is a first tier automotive approved IP67 antenna which has gone through stringent PPAP certification and is

Model no

AA.105TitanMagnetic MountHigh Gain (30dB)

Electrical Data

Centre Freq. 1575.42±MHzGain 30dBic±2noise Figure 1.5dB MaxVSWR 1.92 Max.axial ratio 3.0dB MaxPolarization RHCPImpedance 50ΩInput Voltage 1.8~5.5VPower Consum. @1.8V 2.3mA

@2.7V [email protected] 6mA@5V 10.3mA

Mounting Data

Dimensions 44*33*14mmMounting Magneticoperating Temp. -40°C~+85°CCable* RG-174Connector* SMA(M)IP Rating: IP67

Model no

AA.108TitanAdhesive MountHigh Gain (30dB)First Tier AutomotiveApproved - TS16949

Electrical Data

Centre Freq. 1575.42±MHzGain 30dBic±2noise Figure 1.5dB MaxVSWR 1.92 Max.axial ratio 3.0dB MaxPolarization RHCPImpedance 50ΩInput Voltage 2.7~12VPower Consum. @2.7V 12mA

@3.3V 7mA@5V 7mA

Mounting Data

Dimensions 44*33*14mmMounting Adhesiveoperating Temp. -40°C~+85°CCable* RG-174Connector* SMA(M)IP Rating IP67

Model no

AA.1091 Stage LNA (20dB)Magnetic Mount

Electrical Data

Centre Freq. 1575.42±MHzGain 20dBic±2noise Figure 1.3dB MaxVSWR 2.0 Max.axial ratio 1.0dB MaxPolarization RHCPImpedance 50ΩInput Voltage 2.4~5.5VPower Consum. @3V 7mA Max

@5V 16mA Max.

Mounting Data

Dimensions H:15mm Ø 45mmMounting Magneticoperating Temp. -40°C~+85°CCable* RG-174Connector* SMA(M)IP Rating: IP67

*Cable and Connectors are Customizable, Standard Length is 3M please contact us at [email protected]

GPS - GlonaSS - GnSS | 21

GP

S -

GLO

nA

SS

- G

nSS

GP

S - GLO

nA

SS - G

nSS

*Cable and Connectors are Customizable, Standard Length is 3M please contact us at [email protected] ** A.03 is a ThreeStage version of Hercules for longer cable lengths of >5M.

GPS External antenna SolutionsGPS External antenna Range

a certified shipping part already qualified in the global automotive IMDS database system.

The advantage of the Taoglas solution is the antenna inside is designed by Taoglas GPS antenna engineers and is tuned and customized for its housing and M2M applications, giving the antenna maxi-mum sensitivity. The axial ratio is carefully

optimized in our unique test chambers to reduce multi-path effects and therefore get a higher C/N ratio on your system.

The antenna range was designed based on market feedback - small, waterproof, high gain, durable. All external antennas are available with the cable and connector required to connect directly to your device.

These choices include low loss and special type cables e.g. CFD200.

They are available in 1 stage, 2 stage and 3 stage high gain LNA configurations. Experienced customers often prefer a high gain LNA due to its ability to deliver supe-rior GPS locking in difficult environments.Its the smallest high performance antenna in the market.

Model no

A.01.CHercules2 Stage 30dBScrew Mount

Electrical Data

Centre Freq. 1575.42MHzGain: 30dBic typ. (@3V)noise Figure: 3.0dB Max (@3V)VSWR: 2.0 Max.axial ratio: 3.0dB MaxPolarization: RHCPImpedance: 50ΩInput Voltage 1.8~5.5VPower Consum. @1.8V 6mA Max

@3V 12mA [email protected] 30mA Max.

Mounting Data

Dimensions: H:29mm Ø 52mm(H:1.14” Ø 2.05”)

Mounting: Thread Ø 18mmoperating Temp. -40°C~+85°CCable* RG-174Connector* SMA(M)IP Rating: IP69K

Model no

A.03.B**Hercules3 Stage 40dBScrew Mount

Electrical Data

Centre Freq. 1575.42MHzGain: 40d±dBicnoise Figure: 1.5dB MaxVSWR: 2.0 Max.axial ratio: 3.0dB MaxPolarization: RHCPImpedance: 50ΩInput Voltage 1.8~5.5VPower Consum. @1.8V 8mA Max

@3V 10mA Max@5V 12mA Max.

Mounting Data


Mounting: Thread Ø 18mmoperating Temp. -40°C~+85°CCable* 10M RG-174Connector* SMA(M)IP Rating: IP69K


GP

S -

GLO

nA

SS

- G

nSS

GP

S - GLO

nA

SS - G

nSS

GPS active Embedded antenna ModulesEmbedded GPS active antenna Modules

They connect directly to your GPS module via a cable and connector, or in some cases can be soldered directly onto the edge of your board.

Active antenna patches are already tuned for their own ground plane and LNA and have integrated front end SAW filters,

meaning that they are more resistant to the detuning effects of surrounding components and different device ground planes. They are also much more resistant to device noise than passive antennas, allowing in most cases immediate device integration.

Model no

AP.10E.07.0039B1 Stage 15dB10mm PatchFront End SAW Filter

Electrical

Frequency 1575.42MHzlna Gain(3.0V) 15dB Typ.antenna Gain -10dBicaxial Ratio 4.0dB Maxnoise Figure (3.0V) 2.5dBout Impedance 50ΩPolarization RHCPoutput VSWR 2.0 Maxop. Temp -40°C~+85°CRel. Humidity 40%~95%Input Voltage Min: 1.8V

Typ: 3.0VMax: 5.5V

Power Cons. (3.0V) 3mA

Mounting Data

Dimensions 10*10*5.7mmCable* 39mm Ø 0.81mmConnector* IPEX MHFI

(U.FL comp)

Model no

AP.10F.07.0039B2 Stage 25dB10mm PatchFront End SAW Filter

Electrical


Typ: 3.0VMax: 5.5V


Mounting Data


(U.FL comp)

Model no

AP.12F.07.0045A2 Stage 28dB12mm PatchFront End SAW Filter

Electrical


Typ: 3.0VMax: 5.5V


Mounting Data

Dimensions 13.4*13.4*5.5mmCable* 45mm Ø 1.13mmConnector* IPEX MHFI

(U.FL comp)

active GPS Patch antenna

Modules offer the best

possible GPS performance

for any device that needs

to use internal antennas.



GP

S -

GLO

nA

SS

- G

nSS

GP

S - GLO

nA

SS - G

nSS


Active antenna products simplify design and deliver the extra sensitivity required for accurate and reliable GPS performance. Active antennas deliver the shortest cold start time and best accuracy when compared to any other internal GPS antenna.

Model no

AP.17E.07.0064A1 Stage 15dB17mm PatchFront End SAW Filter

Electrical

Frequency 1575.42MHzlna Gain(3.0V) 15dB Typ.antenna Gain -1.0dBicaxial Ratio 3.0dB Maxnoise Figure (3.0V) 2.5dBout Impedance 50ΩPolarization RHCPoutput VSWR 2.0 Maxop. Temp -40°C~+85°CRel. Humidity 40%~95%Input Voltage Min: 1.8V

Typ: 3.0VMax: 5.5V

Power Cons. (3.0V) 3.5mA

Mounting Data


(U.FL comp)

Model no


Electrical

Frequency 1575.42MHzlna Gain(3.0V) 28dB Typ.antenna Gain -1.5dBicaxial Ratio 3.0dB Maxnoise Figure (3.0V) 2.5dBout Impedance 50ΩPolarization RHCPoutput VSWR 2.0 Maxop. Temp -40°C~+85°CRel. Humidity 40%~95%Input Voltage Min: 1.8V

Typ: 3.0VMax: 5.5V

Power Cons. (3.0V) 7.5mA

Mounting Data

Dimensions 23.8*22.2*8mmCable* 64mm Ø 1.13mmConnector* IPEX MHFI

(U.FL comp)

Model no

AP.25E.07.0054A1 Stage 15dB25mm PatchFront End SAW Filter

Electrical

Frequency 1575.42MHzlna Gain(3.0V) 15dB Typ.antenna Gain +1.5dBicaxial Ratio 3dB Maxnoise Figure (3.0V) 2.5dBout Impedance 50ΩPolarization RHCPoutput VSWR 2.0 Maxop. Temp -40°C~+85°CRel. Humidity 40%~95%Input Voltage Min: 1.8V

Typ: 3.0VMax: 5.5V

Power Cons. (3.0V) Typ. 3mA

Mounting Data


(U.FL comp)

Taoglas active GPS Patch antenna Modules feature front End

SaW Filters; this offers better protection from nearby radiated

power surges, and the SaW Filter also reduces the radiated

spurious emissions in devices.



GP

S -

GLO

nA

SS

- G

nSS

GP

S - GLO

nA

SS - G

nSS


They are available most commonly in 1 stage, 2 stage versions and of course the larger the antenna that can be used the greater the performance.

The AP.35A is the most sensitive off the shelf GPS antenna in the M2M Telematics market. Combining high-zenith gain and low-axial ratio, it can pick up very weak signals at low elevation satellites.

A SAW filter reduces noise entering from the device system, important when considering the close proximity of cellular transmitters and circuitry in today’s miniature devices.

These results combined lead to quicker cold starts and more accurate position and location information.

Model no


Patch

Frequency 1575.42MHzlna Gain(3.0V) 28dBantenna Gain +2.0dBicaxial Ratio 3dB Maxnoise Figure (3V) 3.0dBout Impedance 50ΩPolarization RHCPoutput VSWR Max 2.0op. Temp -40°C~+85°C

Rel. Humidity: 40%~95%

Input Voltage: Min 1.8V Typ. 3.0VMax. 5.5V

Power Cons. (3.0V) Typ.12mA

Mounting Data

Dimensions 25*25*8mmCable* 78mm Ø 1.13Connector* IPEX (U.FL)

(U.FL comp)

Model no

AP.35A.07.0054A1 Stage 15dB35mm PatchBack End SAW Filter

Patch

Frequency 1575.42MHzlna Gain(3.0V) 15dBantenna Gain +2.0dBicaxial Ratio 3dB Maxnoise Figure (3V) 1.5dBout Impedance 50ΩPolarization RHCPoutput VSWR Max 2.0op. Temp -40°C~+85°C

Rel. Humidity: 40%~95%

Input Voltage: Min 1.8V Typ. 3.0VMax. 5.5V

Power Cons. (3.0V) Typ.3mA

Mounting Data

Dimensions 35*35*5.5mmCable* 54mm Ø 1.13Connector* IPEX (U.FL)

(U.FL comp)


Experienced customers

often prefer a high gain lna

due to its ability to deliver

superior GPS locking in

difficult environments.


GP

S -

GLO

nA

SS

- G

nSS

GP

S - GLO

nA

SS - G

nSS

GPS active Embedded antenna ModulesEmbedded GPS active antenna Modules – SMT Mount

aP.10G and aP.10H active

GPS Patches are the smallest

SMT GPS high performance

embedded antenna currently

available in the world

Model no

AP.10G.011 Stage 14dB10mm PatchFront End SAW Filter

Electrical

Frequency 1575.42MHzlna Gain (1.8V) 18dBantenna Gain -10dBic typ.axial Ratio 4.0dB Maxnoise Figure 2.6dBout Impedance 50ΩPolarization RHCPoutput VSWR 2.0Maxop. Temp -40°C~+85°C

Rel. Humidity 40%~95%

Input Voltage Min: 1.5VTyp: 1.8VMax: 3.3V

Power Consump.(1.8V)

3.5mA

Mounting Data

Dimensions 10*10*4mm7.3mm vertical PCB

Mount SMT Mount via Solder Pads

Model no

AP.10H.012 Stage 25dB10mm PatchFront End SAW Filter

Electrical

Frequency 1575.42MHzlna Gain (3.0) 25dBantenna Gain -10dBic typ.axial Ratio 4.0dB Maxnoise Figure (3.0V) 2.5dBout Impedance 50ΩPolarization RHCPoutput VSWR 2.0Maxop. Temp -40°C~+85°CRel. Humidity 40%~95%Input Voltage Min: 1.8V

Typ: 3.0VMax: 3.3V

Power Consump.(3.0V)

10mA

Mounting Data

Dimensions 10*10*4mm7.3mm vertical PCB

Mount SMT Mount via Solder Pads

Using extremely sensitive high dielec-tric constant powder formulation and tight process control the 10*10*4mm patch antenna is accurately tuned to have its frequency band right at 1575.42MHz for GPS systems.

A patented SMT structure gives high reliability in integration. With an ultra low power consumption one stage LNA

with Saw Filter, this small active patch has the performance of an ordinary active patch, but at only a quarter of the size. This product is suited to small form factor mobile devices such as GPS Smartphones, Personal Location, Medical devices, Telematic devices and Automotive navigation and tracking. Custom gain, connector and cable versions are available.


GP

S -

GLO

nA

SS

- G

nSS

GP

S - GLO

nA

SS - G

nSS

GPS Embedded SMT SolutionsSurface mount GPS range

Model no

SGP.12A12mm Patch

Electrical Data

Centre Freq. 1575 MHzBandwidth 4MHz minReturn loss ≤-10dBVSWR 1.5 Max.Gain at zenith -1.0dBic typ.axial Ratio 4dB MaxPolarization RHCPImpedance 50Ω

Mechanical Data

GP Size 45*45mmPatch Dims. 12*12*4.5mmoperatingTemp. -40°C~+85°C

Model no

SGP.15A15mm Patch

Electrical Data

Centre Freq. 1575 MHzBandwidth 3MHz minReturn loss ≤-10dBVSWR 1.5 Max.Gain at zenith 1.0dBic typ.axial Ratio 3dB MaxPolarization RHCPImpedance 50Ω

Mechanical Data


Model no

SGP.18C18mm Patch

Electrical Data


Mechanical Data


Taoglas unique patented SMT (Surface Mount Technology) GPS patches and loop

antennas are designed to meet the requirements of high volume applications that

need to avoid manual assembly processes.


GP

S -

GLO

nA

SS

- G

nSS

GP

S - GLO

nA

SS - G

nSS

GPS Embedded SMT SolutionsSurface mount GPS range

They are unique because the environmen-tal requirements of the automotive industry (temperature, shock, vibration etc) are met with this product.

GPS Patch antenna technology has been proved across industry, to be the best

antenna technology for receiving GPS signals. This is because they offer high gain, a narrow bandwidth and can be right hand circularly polarized thus matching the characteristics of the actual signal itself.

The antennas are delivered on tape and reel and mounted directly onto the PCB via large mounting pads underneath.

Connection is made during the standard reflow process and there is a pad present for soldering to the feed line.

Model no

SGP.25C25mm Patch

Electrical Data


Mechanical Data


Note:

Centre frequencies can be shifted depending on ground-plane size. The aim is to have the antenna receiving at 1575MHz when it is on the PCB.

Tuning services are available if the off the shelf parts do not retain centre frequency inside the GPS device, tuning services are subject to MOQ’s and/or NRE.

*these antennas come on Tape and Reel


GP

S -

GLO

nA

SS

- G

nSS

GP

S - GLO

nA

SS - G

nSS

GPS Embedded PIn PatchesGPS Ceramic Passive Patch Range

Model no

GP.1575.12.4.A.0212mm Patch

Electrical Data

Centre Freq. 1575 MHzBandwidth 6MHz minReturn loss ≤-10dBVSWR 1.5 Max.Peak Gain -0.5dBic typ.Polarization RHCPImpedance 50Ω

Mechanical Data

GP Size 50*50mmPatch Dims. 12*12*4mmoperatingTemp. -40°C ~+85°C

Mounting

Pin 1.65±0.2mmadhesive 0.05mm thick

Model no

GP.1575.15.4.B.0215mm Patch

Electrical Data

Centre Freq 1575MHzBandwidth 6MHz minReturn loss ≤-10dBVSWR 1.5 Max.Peak Gain 1dBic typ.Polarization RHCPImpedance 50Ω

Mechanical Data

GP Size 66*52.5mmPatch Dims. 15*15*4mmoperatingTemp. -40°C ~+85°C

Mounting


Model no

GP.1575.18.2.A.0218mm Patch

Electrical Data

Centre Freq 1575 MHzBandwidth 5MHz minReturn loss ≤-10dBVSWR 1.5 Max.Peak Gain -0.5dBic typ.Polarization RHCPImpedance 50Ω

Mechanical Data


Mounting


GPS Patch antenna Technology has been proved across industry to be the best

antenna technology for receiving GPS signals.


GP

S -

GLO

nA

SS

- G

nSS

GP

S - GLO

nA

SS - G

nSS


This is because they offer high gain, a narrow bandwidth and can be right hand circularly polarized thus matching the characteristics of the actual signal itself.

Taoglas does not recommend any other technology for GPS antennas (unless it is an AGPS application), the larger the GPS patch antenna the better the gain.

Active antennas should always be used at 15mm size, or below, for any standalone GPS applications.

Model no

GP.1575.18.4.A.0218mm Patch

Electrical Data

Centre Freq. 1575 MHzBandwidth 8MHz minReturn loss ≤-10dBVSWR 1.5 Max.Peak Gain 2.5dBic typ.Polarization RHCPImpedance 50Ω

Mechanical Data


Mounting


Model no

GP.1575.25.2.A.0225mm Patch

Electrical Data

Centre Freq 1575MHzBandwidth 5MHz minReturn loss ≤-10dBVSWR 1.5 Max.Peak Gain 2.0dBic typ.Polarization RHCPImpedance 50Ω

Mechanical Data


Mounting


Model no

GP.1575.25.4.A.0225mm Patch

Electrical Data

Centre Freq 1575 MHzBandwidth 10MHz minReturn loss ≤-10dBVSWR 1.5 Max.Peak Gain 3.5dBic typ.Polarization RHCPImpedance 50Ω

Mechanical Data


Mounting



GP

S -

GLO

nA

SS

- G

nSS

GP

S - GLO

nA

SS - G

nSS


Model no

GP.1575.35.3.A.0235mm Patch

Electrical Data

Centre Freq: 1575 MHzBandwidth: 22MHz minReturn loss: ≤-10dBVSWR: 1.5 Max.Peak Gain: 2.0dBic typ.Polarization: RHCPImpedance: 50Ω

Mechanical Data

GP Size 50*50mmPatch Dims. 35*35*3.5mmoperatingTemp. -40°C ~+85°C

Mounting


Note: Please see our SGP series for surface mounted solutions.

Centre frequencies can be shifted depending on ground-plane size, shape and surrounding device.

The aim is to have the antenna receiving at 1575MHz when it is on the PCB.

Tuning services are available if the off the shelf parts do not retain centre frequency inside the GPS device, tuning services are subject to MOQ’s and/or NRE.

applications

Transportation, Defence, Marine, Agriculture and Navigation applications globally choose patch antenna technology for reliable and accurate GPS performance.


GP

S -

GLO

nA

SS

- G

nSS

GP

S - GLO

nA

SS - G

nSS

GPS loop antennasEmbedded GPS Passive and active loop antenna Range

The GLA loop antenna series show at least three times the efficiency of traditional linear polarized 1575MHz antennas. Efficiencies of 40% to 90% are achievable. They are delivered on tape and reel and allow M2M customers to use an Omni-directional antenna in devices where orientation of the product is unknown.

Taoglas have developed a Plug and Play Active version for easier integration, where omni-directionality is important. We have combined a GLA.01 with a one stage LNA

and a SAW Filter to boost the S/N (C/N) of the GPS system and helps to overcome some noise effects from today’s crowded device boards that passive antennas cannot resolve.

The average gain is similar to an 18mm active patch antenna but in a much narrower profile, only 2.3mm at its highest point, allowing this antenna to be used perpendicular to the device main-board, or placed adjacent to the top or bottom of device main board.

Model no

ALA.011 Stage 16dBFront End SAW Filter

Patch

Frequency 1575.42MHzBandwidth 70MHzReturn loss ≤-10dBlna Gain(3.0V) 16±4dBi@90Peak Gain 3.1dBi Typ.noise Figure 1.3dB Maxout Impedance 50ΩPolarization Linearoutput VSWR Max 2.0op. Temp -40°C~+85°CRel. Humidity 10%~95%Input Voltage Min 2.7V

Typ. 3.0VMax. 3.3V

Current(3.0V) Typ.13mA

Mounting Data

Dimensions 45*10*2.3mmCable* Ø1.13 95mmConnector* IPEX (U.FL)

Model no

GLA.01Sub-MiniatureCeramic Loop

Electrical Data

Centre Freq. 1575 MHzBandwidth 50MHzReturn loss ≤-10dBVSWR 2.0 MaxPeak Gain 2.5dBi typ.Polarization LinearImpedance 50Ω

Mechanical Data


Model no

GLA.02MiniatureCeramic Loop

Electrical Data

Centre Freq. 1575 MHzBandwidth 81MHzReturn loss ≤-10dBVSWR 2.0 MaxPeak Gain 3dBi typ.Polarization LinearImpedance 50Ω

Mechanical Data

GP Size 80*40mmPatch Dims. 10*3.2*3.9mmoperatingTemp. -40°C~+85°C

The Taoglas series of GPS

loop antennas are

miniature edge mounted

antennas, designed

for small space

requirements.



GP

S -

GLO

nA

SS

- G

nSS

GP

S - GLO

nA

SS - G

nSS

GPS –GlonaSS External antenna Solution - DominatorGPS-GlonaSS External Magnetic Mount Solution

By combining GLONASS and GPS twin system receivers will capture data from twice as many satellites and will, therefore, provide more accurate and fail-proof precision location, especially in cities or mountains, where terrain may block signals from some satellites.

The AA.161 is a GPS and Glonass antenna designed for applications which require high positioning accuracy by combining signals from GPS and Glonass systems.

It features a high gain wide-band patch antenna on a large integral ground plane which delivers maximum performance.

Taoglas have developed an External active anten-na that covers both GPS and GlonaSS satellite positioning systems.

Model no

AA.161DominatorMagnetic Mount

Patch

Frequency 1574~1610 MHzlna Gain(3.0V) 28dBicantenna Gain 26±[email protected]

27±3dBic@1602MHznoise Figure (3V)2.6dBicout Impedance 50ΩPolarization RHCPoutput VSWR 2.0 Maxop. Temp -40°C~+85°CRel. Humidity 40~95%Input Voltage Min 1.8V

Typ 3.0VMax 5.5V

Power Consp. 10mA

Mounting Data

Dimensions 50*66*21mmCable* RG-174Connector* SMA(M)



GP

S -

GLO

nA

SS

- G

nSS

GP

S - GLO

nA

SS - G

nSS

GPS –GlonaSS active Embedded SeriesEmbedded active antenna Modules

The AGGP series features advanced wide-band ceramic patch antennas with optimized gain, radiation pattterns and axial ratio at GPS and Glonass centre frequencies.

They also include two stage LNA’s com-bined with front-end SAW filters to reduce out of band noise such as from nearby cel-lular transceivers, and improve probability of the wireless device passing radiated

spurious emissions certification. They are produced in TS16949 automotive qual-ity approved facility and 100% tested for gain (S21), return loss (S11) to ensure total consistency of performance.

Cable type, length and connectors can be customized and samples offered according to requirement, subject to minimum order quantities in production.

The aGGP series of GPS – Glonass- GnSS active patch antennas are the best choice embedded antenna with the lat-est generation of GPS-Glonass-GnSS receivers.


Model no

AGGP.25F2 Stage 28dB25mm PatchFront End SAW Filter

Patch

Frequency 1574~1610MHzlna Gain(3.0V) 28dBPatch Gain 1575.40MHz - 1.5dBic@ zenith 1602MHz - 0dBicaxial Ratio 3.0 dBi Maxnoise Figure (3V) 2.6dBout Impedance 50Ωop. Temp -40°C~+85°CRel. Humidity 40%~95%Input Voltage 1.8V~5.5VPower Cons (3V) 10mA

Mounting Data

Dimensions 25.1*25.1*7.4mmCable* 60mm Ø 1.13Connector* IPEX MHFI (U.FL Comp)

Model no

AGGP.35F2 Stage 28dB35mm PatchFront End SAW Filter

Patch

Frequency 1574~1610MHzlna Gain(3.0V) 28dBPatch Gain 1575.40MHz - 1dBic@ zenith 1602MHz - 0dBicaxial Ratio 3.0 dBi Maxnoise Figure (3V) 2.6dBout Impedance 50Ωop. Temp -40°C~+85°CRel. Humidity 40%~95%Input Voltage 1.8V~5.5VPower Cons (3V) 10mA

Mounting Data

Dimensions 35*35*6.9mmCable* 60mm Ø 1.13Connector* IPEX MHFI (U.FL Comp)


GP

S -

GLO

nA

SS

- G

nSS

GP

S - GLO

nA

SS - G

nSS

GPS –GlonaSS Passive antennasEmbedded Ceramic Passive Patch antennas

our extensive CGGP patch antenna range by means of a double resonance design, have

unique wide-band operation over the whole operating bands of GPS and GlonaSS

systems from 1575MHz to 1610MHz.

The CGGP patch range achieves best in class right hand circularly polarized gain with good axial ratio characteristics mitigat-ing multi-path effects which is vital to im-

proved S/N carrier ratio and faster locking times on the device itself. It is mounted via pin and double-sided adhesive.

Model no

CGGP.18.4.C.0218mm Patch

Electrical Data

Recieving Freq. 1574~1610MHzVSWR 1.5 Max.Peak Gain 3.0dBic typ.Polarization RHCPImpedance 50Ω

Mechanical Data


Mounting

Pin 1.8±0.3mmadhesive NITTO 5015

Model no

CGGP.25.4.A.0225mm Patch

Electrical Data

Recieving Freq. 1575~1610MHzBandwidth 15MHz minReturn loss ≤-10dBVSWR 1.5 Max.Peak Gain 5.0dBic typ.Polarization RHCPImpedance 50Ω

Mechanical Data

GP Size 70*70mmPatch Dims. 25.1*25.1*4mmoperatingTemp. -40°C ~+85°C

Mounting


Model no

CGGP.35.3.A.0235mm Patch

Electrical Data

Recieving Freq. 1575~1610MHzBandwidth 26MHz minReturn loss ≤-10dBVSWR 1.5 Max.Peak Gain 1.5dBic typ.Polarization RHCPImpedance 50Ω

Mechanical Data

GP Size 70*70mmPatch Dims. 35*35*3.5mmoperatingTemp. -40°C ~+85°C

Mounting


Note: These antennas have been tuned for a centre position on a 70mm*70mm ground-plane. They are manufactured and tested in a TS16949 first tier automotive approved facility. For further optimization to customer specific device environments where positioning is off centre or on different ground-plane sizes, custom tuned patch antennas can be supplied


GP

S -

GLO

nA

SS

- G

nSS

GP

S - GLO

nA

SS - G

nSS

GPS applications

automotive/TransportationMA.203

AA.105

SGP.25

AP.25F

MA.600

MA.104

Smart MeteringMA.104

MA.501

MA.600

MA.700

A.03

A.01.C

Industrial Handsets/TabletsALA.01

GLA.01

AP.10G.01

AP.10H.01

Combination36 |

Com

bina

tionC

ombination

automotive/ Industrial Screw-Mount - Smallest compactHercules Series 2in1

The Hercules was designed mainly for commercial vehicle and outdoor equipment

installations, with extra thick threads, with unique lowest loss, high external noise

rejection cables exiting through the bottom for ease of install.

The Hercules is a waterproof, high performance antenna that has been designed for heavy duty applications in outdoor environments.

It features extra thick threads and strong washers for sturdy installation. Its outer casing is manufactured from durable UV resistant ABS, protecting it from vandal-ism and direct attack. It also features convenient side slots so that the antenna cables can run easily from the side.

Durable and robust UV resistant ABS housing is resistant to vandalism and direct attack. It is designed for covert mounting as it is only 3cm high when mounted, thus complies with the latest EU directives for height restrictions.

The antenna’s IP69K rating means it is water-proof against high pressure water jets. A synthetic rubber foam seal on the base with 3M adhesive completely pre-vents water entering the mounting hole.

Its the smallest high performance antenna in the market.

Model no

MA.104.CGPS/CellularScrew-Hercules

Electrical Data

GPS 2 Stage Active LNACentre Frequency 1575.42±2MHzGain 30dBic typ. (@3V)noise Figure 3.0dB Max (@3V)Power Consump. 12mA(@3V)Polarization RHCPCellular/Wi-Fi Penta-band 850/900

/1800/1900/2100MHzPolarization LinearImpedance 50ΩVSWR ≤3.5Peak Gain 1.6dBi@880-960Mhz

0.1dBi@1710-1880MHzEfficiency > 20%

Mechanical Data


Mounting: Thread Ø 18mmoperating Temp. -40°C~+85°CCable* 3M RG-174Connector* SMA(M)/SMA(M)IP Rating: IP69K

Model no

MA.501.CGPS/Wi-FiScrew-Hercules

Electrical Data

GPS 2 Stage Active LNACentre Frequency 1575.42±2MHzGain 30dBic typ. (@3V)noise Figure 3.0dB Max (@3V)Power Consump. 12mA(@3V)Polarization RHCPWi-Fi Dual-Band 2.4~2.5GHz

4.9~6.0GHzPolarization LinearImpedance 50ΩVSWR ≤1.8Peak Gain -3dBi 2.4-2.5GHz

4dBi 4.9-6.0GHzEfficiency > 40%

Mechanical Data


Mounting: Thread Ø 18mmoperating Temp. -40°C~+85°CCable* 3M RG-174/CFD-200Connector* SMA(M)/RP-SMA(M)IP Rating: IP69K

Combination | 37

Com

bina

tionC

ombination

automotive/ Industrial Screw-Mount - low ProfileSpartan Series 3in1

The Spartan is unique in the market because it combines a 3in1 GPS, Cellular (2G and 3G) and Wi-Fi, heavy-duty antenna with high efficiency in a compact low profile format at only 35mm high.

The antenna screws down permanently onto a roof or metal panel and can be pole or wall-mounted with a metal bracket. The unique robust metal base serves as its own ground-plane, the antenna has no need for an external ground-plane to mount to. It comes with a waterproof 3M adhesive underlay to permanently prevent any water from leaking under the antenna into the mounting hole.

The Spartan antenna delivers over 37% efficiency and 2dBi+ peak gain at the connector on 3M of cable on frequency ranges of 824-2170MHz for cellular, 2.4/4.9~6GHz for Wi-Fi/Public Safety/Zig-bee and 4dBic for GPS. All while still maintaining 20dB isolation between antennas. The Spartan can also be supplied in single GPS, Cellular, Wi-Fi only configurations or at other frequency bands.

Its the lowest profile three in one antenna in the market at 35.1mm

The Spartan Ma.600 antenna is a heavy-duty, fully IP67 water-proof external M2M antenna for use in telematics,transportation and remote monitoring applications.

GPS

Electrical Data

Frequency 1575.42±2MHzlna 2 Stage 32dB LNAPeak Gain 4.0dBic typ.ave. Efficiency 50%Polarization RHCPImpedance 50ΩVSWR ≤1.9

Mechanical Data

Dimensions H:35.1mm (1.38”)Ø 145.6mm (5.73”)


Cellular

Electrical Data


Peak Gain 2dBi typ.ave. Efficiency 37%Polarization VerticalImpedance 50Ω

Mechanical Data


Mounting Thread Ø 30mmoperating Temp. -40°C~+85°CCable* 3M CFD-200Connector* SMA(M)IP Rating IP67

Wi-Fi

Electrical Data


Peak Gain 3.8dBi typ.ave. Efficiency 48%Polarization VerticalImpedance 50ΩVSWR ≤1.6

Mechanical Data




Model no

MA.600Screw-Mount

Combination38 |

Com

bina

tionC

ombination

automotive/ Industrial Screw-Mount - low ProfileSpartan Series 3in1

GPS

Electrical Data

Frequency 1575.42±2MHzlna 2 Stage 32dB LNAPeak Gain 4.0dBic typ.ave. Efficiency 50%Polarization RHCPImpedance 50ΩVSWR ≤1.9

Mechanical Data



Cellular

Electrical Data


Peak Gain 3.4dBi typ.ave. Efficiency 40%Polarization VerticalImpedance 50Ω

Mechanical Data



915MHz

Electrical Data

Frequency 902~929MHz

Peak Gain 2.3dBi typ.ave. Efficiency 45%Polarization VerticalImpedance 50ΩVSWR ≤1.9

Mechanical Data




Model no

MA.603Screw-Mount

The Spartan MA.603 antenna is unique in the market because it combines 3in1 GPS, Cellular (2G and 3G) and 915MHz anten-nas in a heavy-duty structure with high efficiency in a low profile compact format at 35mm(1.38”) profile Height.

The antenna screws down permanently onto a roof or metal panel and can be pole or wall-mounted.

For industries such as commercial vehicle telematics, remote monitoring, smart meter systems, construction equipment, at only 35mm high, the Spartan provides an unobtrusive, robust, rugged antenna that is durable even in extreme environments.

The Spartan Ma.603 antenna is a low profile, heavy-duty, fully IP67 waterproof external

M2M antenna for use in telematics, transportation and remote monitoring applications.

Combination | 39

Com

bina

tionC

ombination

automotive/ Industrial Screw-Mount - RF ProfessionalPantheon Series 3in1, 4in1

This 3 in1 MA.700 model antenna is a heavy-duty, omni-directional IP67 waterproof external M2M combination antenna for use in telematics, transporta-tion and remote monitoring applications.

The MA.700 is unique in the market because it combines the highest efficiency and peakgain GPS, LTE Cellular (2G and 3G) and Wi-Fi antennas together in a tough housing.

The antenna screws down permanently onto a roof or metal panel and can be pole or wall-mounted with a metal bracket.

The unique robust metal base serves as its own ground-plane, the antenna has no need for an external ground-plane to mount to. It comes with a waterproof 3M adhesive underlay to permanently prevent any water from leaking under the antenna into the mounting hole.

It delivers over 50% efficiency at the connector on 3M (19ft) of cable on frequency ranges of 700-2170MHz for cellular, 2.4/4.9~6GHz for Wi-Fi/Public Safety/Zigbee. Because of this it can pass in most cases network and PTCRB approv-als at 3 metre cable length with a device on the spot. The integral GPS antenna has a peak gain of 4dBiC excluding cable loss. The MA.700 can also be supplied in single GPS, LTE/Cellular, Wi-Fi only configurations or at other frequency bands.

Currently expanding the range to 4 in 1 and 5 in 1 combinations. The combination can be in any frequency bands needed.

The Pantheon Ma.700 Series antennas are for RF professionals who want the best possible performance without compromise.

Model no

MA.700Screw-Mount

GPS2 Stage 32dB LNA

Electrical Data

Frequency 1575.42±2MHzGain 4.0dBic typ.@ Zenithave. Efficiency 50%Polarization RHCPImpedance 50ΩVSWR ≤1.92

Mechanical Data



LTE/CellularWide-Band700-2170MHz

Electrical Data


Gain 2dBi avg.ave. Efficiency 50%Polarization VerticalImpedance 50ΩVSWR ≤3.0

Mechanical Data



Wi-Fi

Electrical Data


ave. Efficiency 55.5%Polarization VerticalImpedance 50ΩVSWR ≤1.92

Mechanical Data



Combination40 |

Com

bination

automotive Interior Mount - automotive Glass/Covert Mount- Stingray Series 2in1

our adhesive mount external antennas offer ease of installation, high performance in compact form factors. They are supplied with high quality durable 3m tape to allow secure fixing onto any surface.

Model no

MA.203GPS/CellularAdhesive-Puck

Electrical Data

GPS 2 Stage Active LNACentre Frequency 1575.42±2MHzGain 30dBic typ. (@3V)noise Figure 1.5dB MaxPower Consump. 19±2mA(@3~5V)Polarization RHCPCellular Penta-band 850/900

/1800/1900/2100MHzPolarization LinearImpedance 50ΩVSWR ≤2.5Efficiency > 20%

Mechanical Data

Dimensions: 55*55*10.8mmMounting: 3M 4612 Tapeoperating Temp. -40°C~+85°CCable* 3M RG-174Connector* SMA(M)/SMA(M)IP Rating: IP65

Model no

MA.206GPS/Wi-FiAdhesive-Puck

Electrical Data

GPS 2 Stage Active LNACentre Frequency 1575.42±2MHzGain 28dBic typ. (@3V)noise Figure 2.0dB Max (@3V)Power Consump. 6mA(@3.5V)Polarization RHCPWi-Fi 2.4~2.5GHzPolarization LinearImpedance 50ΩVSWR ≤1.92Efficiency > 20%

Mechanical Data

Dimensions: 55*55*10.8mmMounting: 3M 4612 Tapeoperating Temp. -40°C~+85°CCable* 3M RG-174Connector* (std) SMA(M)/RP-SMA(M)IP Rating: IP65

Model no

MA.301GPS/CellularMagnetic-Puck

Electrical Data

GPS 2 Stage Active LNACentre Frequency 1575.42±2MHzGain 28dB typ. (@3V)noise Figure 1.5dB MaxPower Consump. 6±2mA(@2.7~3.3V)Polarization RHCPCellular Penta-band 850/900

/1800/1900/2100MHzPolarization LinearImpedance 50ΩVSWR ≤2.5Efficiency > 20%

Mechanical Data

Dimensions: Ø 56.4*17.5mmMounting: Magneticoperating Temp. -40°C~+85°CCable* 3M RG-174Connector* SMA(M)/SMA(M)IP Rating: IP67


The Stingray MA.203 GPS/GSM antenna is a powerful combination of a tuned two stage GPS active ceramic patch and a leading edge Penta-band cellular antenna, making it ideal for applications that require durability, small size and covert installation, with reliable reception and transmission crossing through different mobile networks.

Combination | 41

Com

bina

tion

automotive Interior Mount - automotive Glass/Covert Mount- Stream Series 2in1

The Stream MA.208 GPS/LTE Cellular an-tenna is a low profile, heavy-duty, fully IP67 waterproof external M2M antenna for use by RF professionals in telematics, transpor-

tation and remote monitoring applications. The Stream is unique in the market as it combines the highest possible efficiency and peak gain for GPS and all cellular

bands in 2G/3G/4G in a low profile compact format for mounting via high quality first tier automotive approved 3M adhesive foam.

Model no

MA.208GPS/LTE/GSM/UMTSAdhesive Mount

Electrical Data

GPS 2 Stage Active LNACentre Frequency 1575.42±2MHzGain 30dBic typ.Polarization RHCPCellular LTE 700MHz/824-960

Mhz/1710-2170 MhzPolarization LinearImpedance 50ΩVSWR ≤3.6Peak Gain 1.61dBi 700-960 MHz

0.03dBi 1710-2170 MHzEfficiency > 30%

Mechanical Data

Dimensions: 200.5*66.5*9mmMounting: 3M 9448 B Tapeoperating Temp. -40°C~+85°CCable* 3M RG-174/CFD-200Connector* SMA(M)/SMA(M)IP Rating: IP67


ISM42 |

ISM

ISM

ISM automotive/Industrial Screw-Mount - Smallest CompactHercules Series

It is designed for heavy duty work with extra thick threads.

Durable UV resistant ABS housing is resistant to vandalism and direct attack.The range includes the IS.01 antenna for 433MHz (ISM) licensed band, IS.04 for 868Mhz band, IS.05 for the 915MHz band, and the WS.01 antenna for 2.4GHz/4.9 to 6GHz Dual-Band - Wi-Fi, Zigbee, Bluetooth,

and Public Safety. (see 2.4-5.2GHz External Section for more info on the WS.01).

Omni-directional high gain across all bands ensures constant reception and transmission. At only 29 mm height they comply with the latest EU height restrictions directives for roof-mounted objects, with a diameter of 52 mm. Designed to not catch on tree-branches. The antenna can be mounted on metal structures.


The Hercules is a high performance steel thread mount antenna for external use on mesh networks, vehicles and outdoor and indoor assets.

Model no

IS.01.B433MHzScrew-Mount

Electrical Data

Frequency 400-460MHzGain 0dBiReturn loss -16dBRadiation Pattern OmniPolarization Linear - HorizontalImpedance 50ΩVSWR ≤ 2.0

Mechanical Data

Dimensions(mm) H:29 ø 52mm(H:1.14” ø 2.05”)

Mounting Thread 18mmoperating Temp. -40°C~+85°CCable 3M CFD-200Connector SMA(M)IP Rating IP69K

Model no


Electrical Data

Frequency 868-870MHzGain 1.98dBi typ.Return loss -13dBiRadiation Pattern OmniPolarization Linear - HorizontalImpedance 50ΩVSWR ≤ 2.5Efficiency >30%

Mechanical Data


Mounting Thread 18mmoperating Temp. -40°C~+85°CCable 3M RG-174Connector SMA(M)IP Rating IP69K

Model no


Electrical Data

Frequency 902-928MHzGain 1.85dBi typ.Return loss -15dBRadiation Pattern OmniPolarization Linear - HorizontalImpedance 50ΩVSWR ≤ 2.5Efficiency > 25%

Mechanical Data


Mounting Thread 18mmoperating Temp. -40°C~+85°CCable 3M RG-174Connector SMA(M)IP Rating IP69K

ISM | 43

ISM

ISM

omni-directional Fiberglass Series Barracuda Series

In practice no antenna is truly 100% Omni-directional. The best one can achieve is an antenna which has a doughnut shaped radiation pattern all around the antenna housing itself such as these “Omnis”. Omnis give the best value because they give maximum coverage range in the

horizontal (azimuth) plane in 360 degrees thus minimizing the amount of nodes needed for a mesh network.

Our high quality Fiberglass housings are more robust and safer than traditional whip antennas.

They can be connected directly to the access point or telemetry unit or they can be fixed to a pole or wall and connected via any type of customer specified cable and connector

Model no

OMB.868868MHzOmni-DirectionalDipole Antenna

Electrical Data

Frequency 800~870MHzGain 5dBi Radiation Pattern OmniPolarization VerticalImpedance 50ΩVSWR ≤ 1.5Max Input Power 50W

Mechanical Data

Dimensions(mm) H:1093.5 ø 26mmMounting Wall/Pole

Mount Bracketoperating Temp. -40°C~+85°Capplication Indoor/OutdoorConnector* N Type FemaleWind Resistance >150mph(>241km/h)

Model no

OMB.2422.4~2.5GHzOmni-DirectionalDipole Antenna

Electrical Data

Frequency 2400~2500MHzGain 8.0dBi typ. Radiation Pattern OmniPolarization VerticalImpedance 50ΩVSWR ≤ 1.3Max Input Power 50W

Mechanical Data

Dimensions(mm) H:523 ø 26mmMounting Wall/Pole

Mount Bracketoperating Temp. -40°C~+85°Capplication Indoor/OutdoorConnector* N Type FemaleWind Resistance >150mph(>241km/h)

Taoglas range of omni directional base station antennas are the starting point for any mesh network solution. an omni directional antenna means that the power is radiated uniformly in all directions.

ISM44 |

ISM

ISM

The ISM 433MHz, 868MHz, 915MHz and 2400MHz bands are license free bands mainly used in short range applications.

Terminal Mount RangeISM (Industrial Scientific Medical) Terminal antenna Range

Model no

TI.08.A.0111868MHzStraight

Electrical Data

Frequency 868~870MHzPeak Gain - 1.7dBiEfficiency 35%Radiation Pattern OmniPolarization LinearImpedance 50ΩVSWR ≤ 1.5

Mechanical Data

Dimensions 168*12*12mmMounting Straight Fixedoperating Temp. -40°C~+85°CConnector SMA(M)IP Rating IP65

Model no

TI.08.C.0112868MHzFixed R/A

Electrical Data

Frequency 853-883MHzGain 0dBi typ.Radiation Pattern OmniPolarization LinearImpedance 50ΩVSWR ≤ 2.3

Mechanical Data

Dimensions 52.8*17.1*9.6mmMounting R/A Fixedoperating Temp. -40°C~+85°CConnector SMA(M)RAIP Rating IP65

Model no

TI.09.A.0111915MHzStraight

Electrical Data

Frequency 902-928MHzGain 0dBi typ.Return loss -22dBRadiation Pattern OmniPolarization LinearImpedance 50ΩVSWR ≤ 1.1

Mechanical Data

Dimensions 168*12*12mmMounting Straight Fixedoperating Temp. -40°C~+85°CConnector SMA(M)IP Rating IP65

ISM | 45

ISM

ISM

We have a range of different gain antennas in different sizes and are constantly updating our range. If you don’t see what you want here please contact a local Taoglas sales representative.

Many customers specify high peak gain as their main requirement, but the real key to choosing terminal antenna performance is uniformity of production quality across batches as these antennas are notoriously

difficult to produce with uniform frequency response. Many unscrupulous antenna manufacturers ship out detuned unreliable products from batch to batch.


Model no

TI.10.0112433MHzFixed R/A

Electrical Data

Frequency 433-435MHzPeak Gain -11dBi typ.Return loss -15dBRadiation Pattern OmniPolarization LinearImpedance 50ΩVSWR ≤ 2.0

Mechanical Data

Dimensions 45*7.8*17mmMounting R/A Fixedoperating Temp. -40°C~+85°CConnector SMA(M)RAIP Rating IP65

Model no

TI.10.0111433MHzStraight

Electrical Data

Frequency 433-435MHzPeak Gain -7.9dBi typ.Return loss -17dBRadiation Pattern OmniPolarization LinearImpedance 50ΩVSWR ≤ 2.2

Mechanical Data

Dimensions 48*7.8*7.8mmMounting Straight Fixedoperating Temp. -40°C~+85°CConnector SMA(M)IP Rating IP65

Model no

TI.15.3113433MHzHinged 90°

Electrical Data

Frequency 433-435MHzPeak Gain -4.7dBi typ.Return loss -25 dBRadiation Pattern OmniPolarization LinearImpedance 50ΩVSWR ≤ 1.5

Mechanical Data

Dimensions 198*12*12mmMounting Hinged 90°operating Temp. -40°C~+85°CConnector SMA(M)IP Rating IP65

ISM46 |

ISM

ISM


Model no

TI.18868MHzHinged 90°

Electrical Data

Frequency 868~870MHzPeak Gain 3dBi typ.Efficiency 92%Radiation Pattern OmniPolarization LinearImpedance 50ΩVSWR ≤ 1.9

Mechanical Data

Dimensions L:376mm ø 13.1mmMounting Hinged 90°operating Temp. -40°C~+85°CConnector SMA(M)IP Rating IP65

Model no

TI.19915MHzHinged 90°

Electrical Data

Frequency 902~928MHzPeak Gain 2.5dBiEfficiency 82%Radiation Pattern OmniPolarization LinearImpedance 50ΩVSWR ≤ 1.9

Mechanical Data

Dimensions L:379mm ø 13mmMounting Hinged 90°operating Temp. -40°C~+85°CConnector SMA(M)IP Rating IP65

In contrast every Taoglas product is tested rigorously and has to match our specification regarding VSWR/return loss at all frequencies in the band thus ensuring complete reliability of performance. Custom antennas can be designed quickly on request, this service will be subject to an MOQ and/or NRE.

ISM | 47

ISM

ISM

Embedded ISM Flexible Series (with Cable & Connector)

Flexible circuit antennas have been used in many modern mobile phone antenna designs. The material performs very well at higher ISM band frequencies. The products from this range are used where there is no space on the device PCB for an onboard antenna, or there is a lot of metal

present on the main PCB e.g. inside a meter system. The antenna can be stuck directly to the device plastic housing or glass by pulling off the 3M label and using the automotive grade 3M glue that is on one side of the antenna.

Model no

FXP240433MHz

Electrical Data

Working Freq. 433~435MHzPeak Gain 0dBi typ.Radiation Pattern OmniPolarization LinearImpedance 50ΩReturn loss -20dBEfficiency ≤ 40%VSWR ≤ 2.0

Mechanical Data

Dimensions 75*45*0.1mmoperating Temp. -40°C~+85°CCable (Std)* 100mm ø 1.13Connector (Std)* IPEX U.FL compMaterial Flex Polymeradhesive Tape 3M 467

Model no

FXP245450Mhz

Electrical Data

Working Freq. 450~457MHzPeak Gain 0dBiRadiation Pattern OmniPolarization LinearImpedance 50ΩReturn loss -20dBEfficiency ≤ 40%VSWR ≤ 2.0

Mechanical Data


Model no

FXP270784MHz

Electrical Data

Working Freq. 779~787MHzPeak Gain 1.4dBiRadiation Pattern OmniPolarization LinearImpedance 50ΩReturn loss -20dBEfficiency ≤ 40%VSWR ≤ 2.0

Mechanical Data


*Cable and Connectors are Customizable.

Taoglas uniquely supplies highest gain omni-directional flexible circuit antenna solutions for the M2M market.

ISM48 |

ISM

ISM Embedded Flexible Circuit (with Cable & Connector)

Model no

FXP280868Mhz

Electrical Data


Mechanical Data


Model no

FXP290915MHz

Electrical Data


Mechanical Data


Despite the extremely thin material the antennas are very robust and pass the required device temperature and vibration/shock tests. Cable and connector are fully

customizable and IPEX MHF (U.FL compatible) and MMCX are standard. Custom surface mount flexible solutions have also been developed.

ISM | 49

ISM

Embedded ISM Rigid Series (with Cable & Connector) FR4 PCB antennas developed especially for ISM bands

The PC31 dual band 868~915MHz PCB antenna, and the PC81 and PC91 for 868MHz and 915MHz respectively are FR4 PCB antennas designed especially for ISM applications, they have been designed to maximise gain and efficiency in an omni-directional pattern. Cables and Connectors are customizable.

The PC series are ground-plane independent antennas which save on space, making them suitable for even smaller sized M2M devices in tracking, navigation, automotive and telemedical markets.

Model no

PC81868Mhz

Electrical Data

Working Freq. 868-870MhzPeak Gain 2.5dBiRadiation Pattern OmniPolarization LinearImpedance 50ΩReturn loss <-10dBVSWR ≤ 2.0Efficiency > 50%

Mechanical Data

Dimensions 34*7*0.8mmoperating Temp. -40°C~+85°Coperating Temp. 100mm ø 1.13Connector (Std)* IPEX U.FL compMaterial FR4 with foamFoam Dims 16*7*6.3mm

Model no

PC91915Mhz

Electrical Data

Working Freq. 902-928MhzPeak Gain 2dBiRadiation Pattern OmniPolarization LinearImpedance 50ΩReturn loss <-10dBVSWR ≤ 2.0Efficiency > 50%

Mechanical Data

Dimensions 34*7*0.8mmoperating Temp. -40°C~+85°Coperating Temp. 100mm ø 1.13Connector (Std)* IPEX U.FL compMaterial FR4 with foamFoam Dims 13*7*6.3mm

Model no

PC31868/915Mhz

Electrical Data

Working Freq. 868-870Mhz902-928Mhz

Peak Gain 2.3dBi / 1.6dBiRadiation Pattern OmniPolarization LinearImpedance 50ΩReturn loss <-25dBVSWR ≤ 2.0Efficiency > 75%

Mechanical Data


ISM50 |

ISM

ISM

Model no

ILA.01915Mhz

Electrical Data

Working Freq. 902~928MhzPeak Gain 1dBiRadiation Pattern OmniPolarization LinearImpedance 50ΩReturn loss <-19dBVSWR ≤ 2.0Efficiency 70% Typ.

Mechanical Data

Dimensions 10*3.2*0.5mmoperating Temp. -40°C~+85°CConnector (Std)* SMTMaterial Ceramic

Model no

ILA.02868Mhz

Electrical Data

Working Freq. 855~881MhzPeak Gain 2.4dBiRadiation Pattern OmniPolarization LinearImpedance 50ΩReturn loss <-19dBVSWR ≤ 2.0Efficiency 65% Typ.

Mechanical Data

Dimensions 10*3.2*0.5mmoperating Temp. -40°C~+85°CConnector (Std)* SMTMaterial Ceramic

on Board ISM antenna Solutions (SMT) Ceramic loop SMT antennas

The ILA.01 for 915MHz and ILA.02 for 868MHz, have efficiencies of between 40-70%, these loop antennas show at least three times the efficiency of traditional chip antennas. The ILA series at 0.5mm high is the lowest profile SMD IMD antenna solution in the market. With a small total footprint size including ground clearance area of 11*10.2mm this is suitable for devices that have space constraints. Based on the loop effect the ILA series

of antennas work best when placed on the centre of the edge of the board, but can still work better than traditional chip antennas even when placed at corners as substitute.The ILA series is delivered on tape and reel and will allow customers in Automated Meter Reading (AMR), remote monitoring and healthcare markets achieve better RF reception and transmission when connecting with stand-alone devices.

Taoglas have developed ceramic miniature loop antennas for ISM (Industrial Scientific Medical) wireless communications.

ISM | 51

ISM

ISM

Ceiling Mount ISM SolutionCrusader

The crusader has high peak gain and exceptional efficiency across all bands enabling very wide coverage areas and high speed data rates.

The radiation pattern has excellent Omni-directional properties at all frequencies, a unique feature of this wide-band antenna compared to other designs in the market which tend to have nulls at certain bands. This antenna would provide all CPE and

Hotspot needs literally “under one roof”.

The attractive, extremely light, and covert design allows the antenna to be easily mounted on a ceiling, and is suited to any indoor area that requires a Wireless Network - Hotels, Confer-ence Centres, Exhibition Halls, Offices, and Retail Outlets etc. The design is unobtrusive, only 97.5mm in height, and blends in to any environment.

Taoglas Ceiling Mount antenna CM.02 is a wideband antenna solution, 700 MHz to 6GHz, covering all cellular (2G, 3G,4G), and Wi-Fi 802.11, and many other ISM applications in one antenna.

Model no

CM.02High Peak Gain, High Efficiency Ceiling Antenna

Electrical Data

Frequency(GHz) 0.7~1.0 1.0~2.0 2.0~3.0 3.0~4.0 4.0~5.0 5.0~6.0Peak Gain 1.6dBi typ. 1.9dBi typ. 3.0dBi typ. 3.6dBi typ. 3.6dBi typ. 4.4dBi typ.ave. Efficiency 88% 87% 85% 81% 73% 65%Polarization Linear-VerticalImpedance 50ΩRadiation Pattern Omni

Mechanical Data

Dimensions H:97.5mm Ø 167.5mmMounting Thread Ø 17.25mmoperating Temp. -40°C~+85°CCable* 0.3M RG-58Connector* N Type FemaleIP Rating IP65


WiFi/zigBee/Public Safety52 |

WiF

i/Zi

gBee

/P

ublic

Saf

etyW

iFi/ZigBee/

Public Safety

Model no

WS.01.B2.4GHz/5.2GHzHercules Screw-Mount

Electrical Data

Frequency 2400~2500MHz5150~5900MHz

Gain 4dBiout. Impedance 50ΩPolarization LinearRadiation Omni-DirectionalVSWR < 1.8.0:1op. Temp. -40°C~+85°C

Mounting Data

Dimensions 52*29mm2.04”*1.14”

Cable 3M CFD 200Connector RP-SMA(M)*Mounting Screw Mount IP Rating IP69K

2.4GHz automotive/ Industrial Screw-Mount -Smallest compactHercules WS.01

The new Generation Hercules (Gen II) is a high performance steel thread-mount dual-band Wi-Fi antenna for external use on vehicles and outdoor assets worldwide. omni-directional high gain across all bands ensures constant reception and transmission.

WS.01 Hercules is a high efficiency, high gain thread mount dual band wireless antenna for external use on vehicles and outdoor assets worldwide. Omni-directional

gain across both bands ensures constant reception and transmission making the WS.01 an ideal solution for a Zigbee Wireless Mesh for remote applications

e.g. – remote metering.


WiFi/ZigBee/Public Safety | 53

WiF

i/Zi

gBee

/P

ublic

Saf

etyW

iFi/ZigBee/

Public Safety

2.4GHz antenna Solutions Embedded (Internal)Embedded Wi-Fi /zigbee / BT antenna Solutions

Part of the Taoglas offering for wireless applications includes a range of Bluetooth / Wi-Fi / Wlan / 802.11 / zigbee solutions. all 802.11a requirements are supported. These antennas are used for shorter range applications.

Model no

PA. 152.4GHzCeramic PIFA

Electrical Data

Frequency 2400~2500MHzPeak Gain -3dBiReturn loss -21dBImpedance 50ΩPolarisation Linearop. Temp. -40°C~+85°C

Mounting Data

Dimensions 8.7*6.2*3.2mmMounting SMT Mount

Model no

WLA.012.4GHzCeramic PIFA

Electrical Data

Frequency 2450MHzPeak Gain 2.5dBiReturn loss -22dBImpedance 50ΩPolarisation Linearop. Temp. -40°C~+85°C

Mounting Data

Dimensions 3.2*1.6*0.6mmMounting SMT Mount

Model no

WLP.252.4GHzCeramic Patch

Electrical Data

Frequency 2450MHzPeak Gain 5.0dBicReturn loss -30dBImpedance 50ΩPolarisation RHCPop. Temp. -40°C~+85°C

Mounting Data

Dimensions 25*25*4.5mmMounting Pin

NITTO #5015

Please check out our new high efficiency Embedded SMT and Cable Connection Dual-band 2.4GHz/5GHz antennas if using 802.11n


WiF

i/Zi

gBee

/P

ublic

Saf

etyW

iFi/ZigBee/

Public Safety

2.4GHz antenna Solutions Embedded (Internal)Embedded Wi-Fi /zigbee / BT antenna Solutions

We have developed a ceramic miniature loop antenna for 2.4GHz wireless commu-nications. The WLA.01 has been designed for WLAN, Zigbee and Bluetooth mobile devices and modules, which have very small space requirements. This antenna has efficiencies of between 40-80%+, it

shows at least three times the efficiency of the existing traditional chip antennas from leading brands on small board sizes.

Taoglas have introduced a 12*12*4mm; high gain; 2.4GHz SMT patch antenna, which is ideally suited for high performance

industrial applications in Wi-Fi, ISM, Zigbee bands. Also the new WLP.25 Ceramic patch (25*25*4mm), its high gain performance is a perfect solution for metering and remote monitoring applications; it can deliver longer range than smaller chip antennas.

Model no

SWLP.122.4GHzSMT Ceramic Patch

Electrical Data

Frequency 2400~2500MHzPeak Gain 2dBiReturn loss -9dBImpedance 50ΩPolarisation Linearop. Temp. -40°C~+85°C

Mounting Data

Dimensions 12*12*4mmMounting SMT Mount

Model no

CA.142.4GHzUltra SmallChip Antenna

Electrical Data

Frequency 2400~2500MHzPeak Gain 1dBiReturn loss ≤-10dBImpedance 50Ωop. Temp. -40°C~+85°C

Mounting Data

Dimensions 3*3*1mmMounting SMT

Please check out our new high efficiency Embedded SMT and Cable Connection Dual-band 2.4GHz/5GHz antennas if using 802.11n


WiF

i/Zi

gBee

/P

ublic

Saf

etyW

iFi/ZigBee/

Public Safety

2.4GHz antenna Solutions Embedded (Cable & Connector)Embedded Wi-Fi/ zigBee / BT PCB and Flexible antenna Solutions

our PCB antennas come in single-band or multi-band solutions, starting from 433MHz up to 6 GHz. This range covers all standard communication bands in use worldwide today.

Model no

PC112.4GHz/5.2GHzFR4 PCB

Electrical Data

Frequency 2.4GHz/5-6GHzPeak Gain 2dBiVSWR 1.8dB MaxEfficiency 85%Return loss -21dBImpedance 50ΩPolarization Linearop. Temp. -40°C~+85°C

Mounting Data

Dimensions 66*16*0.8mmCable* Ø1.13 100mmConnector* IPEX (U.FL)Mounting N/A

Model no

FXP70Freedom 2.4GHzGeneral Solution

Electrical Data

Frequency 2400-2500MHzPeak Gain 5dBiVSWR 1.5dB MaxEfficiency 80%Return loss -20dBImpedance 50ΩPolarization Linearop. Temp. -40°C~+85°C

Mounting Data

Dimensions 27*25*0.1mmCable* Ø1.13 53mmConnector* IPEX (U.FL)Mounting 3M 467Tape

Model no

FXP72Freedom 2.4GHzGround Coupling

Electrical Data

Frequency 2400-2500MHzPeak Gain 4dBiVSWR 2.0dB MaxEfficiency 70%Return loss -14dBImpedance 50ΩPolarization Linearop. Temp. -40°C~+85°C

Mounting Data


*Cables and Connectors Customizable**For 802.11n applications please check out our new patent pending high peak gain, high efficiency Dual-band FXP-810 and FXP-830 series antennas.


2.4GHz antenna Solutions Embedded (Cable & Connector)Embedded Wi-Fi/ zigBee / BT PCB and Flexible antenna Solutions

Taoglas have developed high peak gain, high efficiency FXP technology Flex-ible Antennas for 2.4GHz, which boost coverage and data-speed performance of Wi-Fi 802.11, ZigBee, Bluetooth and ISM applications. We have a range of sizes available,and cable length and connectors

are fully customizable. These antennas have been designed to work on different plastics material and thickness.

The FXP70 and FXP73 can be adhered directly to a device housing and the FXP72 is designed for the antenna to be placed

parallel between a battery and the main device PCB with just the leading edge sticking out from the edge of the PCB, thus being ideal and providing higher performance for small tag devices where on-board antennas cannot be mounted

Model no

FXP73Blue Diamond2.4GHz

Electrical Data

Frequency 2400~2483.5MHzPeak Gain 2.5dBiVSWR 1.5dB MaxEfficiency 50%Return loss -20dBImpedance 50ΩPolarization Linearop. Temp. -40°C~+85°C

Mounting Data


*Cables and Connectors Customizable**For 802.11n applications please check out our new patent pending high peak gain, high efficiency Dual-band FXP-810 and FXP-830 series antennas.

WiFi/ZigB

ee/P

ublic Safety


2.4GHz/5GHz Dual Band antenna Solutions – Embedded SMTDual Band SMT Ceramic antenna

Model no

SDWA.01Dual-Band 2.4GHz4.9-5.8GhzCeramic SMT Antenna

Electrical Data


Peak Gain 1.05dBi (2.4-2.5GHz)4.91dBi(4.9-5.8GHz)

Efficiency 60-75%Return loss ≤-27dBImpedance 50ΩPolarization Linearop. Temp. -40°C~+85°C

Mounting Data

Dimensions 10*4*1.5mmMounting Ag (Pb Free)

The SDWa.01 dual-band SMT ceramic antenna is an embedded high efficiency, high peak gain solution for Wi-Fi 802.11n and other ISM band applications which require high data speed rates and wide coverage areas.

It is designed to perform optimally mounted in the corner of a device main-board. Two SDWA.01 antennas can be used for

optimal performance for MIMO applica-tions. Its low profile allows use on extremely thin devices while still maintaining highest

RF performance characteristics. All that is needed is a 50 Ohm co-planar waveguide (CPW) to the module.

WiF

i/Zi

gBee

/P

ublic

Saf

ety


WiF

i/Zi

gBee

/P

ublic

Saf

etyW

iFi/ZigBee/

Public Safety

2.4GHz/5GHz Dual Band antenna Solutions Embedded (Cable & Connector)2.4-4.9GHz to 6.0GHz Flexible PCB antennas - Freedom Range

Model no

FXP810Dual-Band 2.4GHz4.9-6.0Ghz

Electrical Data



Efficiency 56%(2.4-2.5GHz)78%(4.9-6.0GHz)

Return loss ≤-27dBImpedance 50ΩPolarization Linearop. Temp. -40°C~+85°C

Mounting Data

Dimensions 31*31*0.1mmCable* Ø1.37 100mmConnector* IPEX (U.FL comp)Mounting 3M 467 Tape

Model no


Electrical Data



Efficiency 50%(2.4-2.5GHz)86%(4.9-6.0GHz)

Return loss ≤-26dBImpedance 50ΩPolarization Linearop. Temp. -40°C~+85°C

Mounting Data

Dimensions 47*7*0.1mmCable* Ø1.37 100mmConnector* IPEX (U.FL comp)Mounting 3M 467 Tape

Model no


Electrical Data



Efficiency 56%Return loss ≤-26dBImpedance 50ΩPolarization Linearop. Temp. -40°C~+85°C

Mounting Data

Dimensions 45*7*0.1mmCable* Ø1.37 100mmConnector* IPEX (U.FL comp)

*Cables and Connectors Customizable

The Taoglas FXP series are conformal flexible antennas and can fit irregular housings.

Responding to the demands of the latest 802.11n applications such as real-time video streaming which need the highest data speeds, Taoglas has developed patent pending unique high efficiency (80%+) Flexible Polymer Dual-Band Antennas that cover 2.4GHz and 4.9GHz to 6GHz.The FXP810 and FXP830/1 are breakthrough very high efficiency small Dual Band Dipole antennas for 2.4/4.9-6GHz bands.

The FXP810 has a peak gain of 1.5dBi at 2.4GHz and efficiencies of 60-70%,

increasing to 5dBi and 80-90% along bands 4.9GHz to 6GHz.

At 31*31*0.1mm in size this antenna is uniquely valuable for small tag type mobile devices in that it can slip between the battery and the main PCB ground of small devices to get increased performance from the ground coupling effect.

The FXP830/1 has a peak gain of 1.8dBi at 2.4GHz and efficiencies of 50%, and 3-4dBi and 80-90% along bands 4.9GHz to 6GHz.

These Taoglas patent pending antennas are unique in the market because they are made from flexible material, have a tiny form factor (42*7*.01mm) and have double-sided 3M tape for easy “peel and stick” mounting. The FXP830/1 are the ideal all-round antenna solutions for squeezing into narrow spaces and still maintaining high performance, for example at the top of LCD devices.


WiF

i/Zi

gBee

/P

ublic

Saf

etyW

iFi/ZigBee/

Public Safety

2.4GHz/5GHz External (Terminal Mount)External 2.4GHz/5GHz antenna Solutions Terminal Mount

**Also available with RP-SMA Plug connectors*Custom antenna connector and gain versions available for a purchase order for a minimum order quantity MOQ and/or NRE

Taoglas offer an extensive range of antennas including Wi-Fi, 802.11, zigbee and Bluetooth for wireless applications, omni-directional gain across all bands ensures constant reception and transmission with these types of antennas.

Model no

GW.112.4GHzHinged

Electrical Data

Frequency 2400~2500MHzGain 1.8dBiout. Impedance 50ΩPolarization LinearRadiation Omni-DirectionalVSWR Max 1.92op. Temp. -40°C~+85°C

Mounting Data

Dimensions (mm) L=84 Ø 7.8Connector* RP-SMA(M)Mounting Hinged 90°

Model no

GW.152.4GHzHinged

Electrical Data

Frequency 2400~2500MHzGain 2dBiout. Impedance 50ΩPolarization LinearRadiation Omni-DirectionalVSWR Max 1.8op. Temp. -40°C~+85°C

Mounting Data

Dimensions (mm) L=108 Ø 7.8Connector* SMA(M)Mounting Hinged 90°

Model no

GW.262.4GHzFixed R/A

Electrical Data

Frequency 2400~2500MHzGain 0dBiout. Impedance 50ΩPolarization LinearRadiation Omni-DirectionalVSWR Max 2.0op. Temp. -40°C~+85°C

Mounting Data

Dimensions (mm) L=28.1 Ø 7.9Connector* SMA(M)**Mounting Fixed 90°


WiF

i/Zi

gBee

/P

ublic

Saf

etyW

iFi/ZigBee/

Public Safety

Model no

GW.262.4GHzStraight

Electrical Data

Frequency 2400-2500MHzGain 0dBiout. Impedance 50ΩPolarization LinearRadiation Omni-DirectionalVSWR Max 1.2op. Temp. -40°C~+85°C

Mounting Data

Dimensions (mm) L=28.5 Ø 7.9Connector* SMA(M)**Mounting Fixed Straight

Model no

GW.582.4GHz/5.2GHzHinged

Electrical Data

Frequency 2400-2500MHz5150-5900MHz

Gain 3dBiout. Impedance 50ΩPolarization LinearRadiation Omni-DirectionalVSWR < 2.0op. Temp. -40°C~+85°C

Mounting Data

Dimensions (mm) L=197 Ø 1.3Connector* RP-SMA(M)Mounting Hinged 90°

Model no

GW.712.4GHz/5.2GHzTerminal-Hinged

Electrical Data


Gain 5dBiout. Impedance 50ΩPolarization LinearRadiation Omni-DirectionalVSWR < 2.0op. Temp. -40°C~+85°C

Mounting Data

Dimensions (mm) L=197 Ø 13Connector* RP-SMA(M)Mounting Hinged 90°

2.4GHz/5GHz External (Terminal Mount)External 2.4GHz/5GHz antenna Solutions Terminal Mount

The antenna structures are designed for robust handling with housings made with TPE, which gives superior environmental reliability and a quality finish.

The hinged versions, GW.11, GW.15, GW.58 and GW.71 antennas can be rotated

90 degrees on the base hinge for ease of placement. Connector mount is fully cus-tomizable. Taoglas terminal antennas are 100% tested for accurate VSWR/return loss to match their product specification, unlike many unscrupulous antenna manufacturers whose shipping product does not match

their specification.External antennas deliver the best performance for any wireless device and Taoglas solutions are available in different gain versions for different range or power requirements.

**Also available with RP-SMA Plug connectors*Custom antenna connector and gain versions available for a purchase order for a minimum order quantity MOQ and/or NRE


WiF

i/Zi

gBee

/P

ublic

Saf

etyW

iFi/ZigBee/

Public Safety

2.4GHz/5GHz antenna Solutions ExternalExternal 2.4GHz/5GHz antenna Solutions

Taoglas offer an extensive range of high performance external antennas for Wi-Fi 802.11, zigbee, ISM wireless applications.

Model no

WA.500w2.4-4.9-6.0GHzStingrayAdhesive

Electrical Data


Gain 4±4dBiout. Impedance 50ΩPolarization LinearRadiation Omni-DirectionalVSWR < 1.92:1op. Temp. -40°C~+85°C

Mounting Data

Dimensions 55*10.8mmCable* 3M RG-174Connector RP-SMA(M)*Mounting 3M TapeIP Rating IP65

The WA.500 is a high efficiency, high gain adhesive mount dual band wireless antenna.

Its high quality low profile covert housing can be attached onto the glass or plastic.

The WA.500w waterproof IP67 version is designed for applications that require Omni-directional gain across both bands to ensure wide coverage area and constant reception and transmission for Wi-Fi and Zigbee applications. The Taoglas range of

panel directional antennas offer high gain for permanent wall, pole or roof mounting. They are very rugged and completely weatherproof for extremely long life in the harshest of environments. Brackets are included.

Model no

FG.PANEL.012.4GHzPanel AntennaU-bolt

Electrical Data

Frequency 2400-2500MHzGain 9dBiout. Impedance 50ΩPolarization Horizontal/Radiation VerticalVSWR < 2.0:1op. Temp. -40°C~+85°C

Mounting Data

Dimensions 220*125*35mmConnector N Type FemaleMounting Pole/Wall

Model no

FG.PANEL.022.4GHzPanel AntennaU-bolt

Electrical Data

Frequency 2400-2500MHzGain 12dBiout. Impedance 50ΩPolarization Horizontal/Radiation VerticalVSWR < 2.0:1op. Temp. -40°C~+85°C

Mounting Data

Dimensions 218*200*35mmConnector N Type FemaleMounting Pole/Wall

*Cable and connectors customizable


WiF

i/Zi

gBee

/P

ublic

Saf

etyW

iFi/ZigBee/

Public Safety

2.4GHz MIMo antennaTrinity MIMo

The Trinity MIMo antenna is a powerful 3*3 3dBi External 2.4GHz omni directional antenna to enable high-speed data throughout.

3 individual high-gain elements ensure maximum coverage through diversity. Desk-top placement, magnet-mounting, wall-mounting, adhesive mounting are

all options. The individual antennas can articulate horizontally and vertically for best signal reception depending on mounting conditions.

Model no

WMA.012.4~2.5GHz3*3 MIMO Antenna

Electrical Data

Frequency 2400~2500MHzPeak Gain 3dBiReturn loss ≤-10dBImpedance 50ΩPolarization Linear Verticalop. Temp. -40°C~+85°C

Mounting Data

Dimensions 10*4*1.5mmMounting Desk/Wall/MagnetCable(Std x3) RG-174Connector(Stdx3) RP-SMA(M)


WiF

i/Zi

gBee

/P

ublic

Saf

etyW

iFi/ZigBee/

Public Safety

Smart MeteringMA.501

WS.01

WLA.01

FXP.73

FXP.72

SWLP.12

WLP.25

MA.600

Industrial Handsets/TabletsFXP.73

WLA.01

SWLP.12

FXP.831

SDWA.01

WiFi/zigBee/Public Safetyapplications

64 | Satellite Communications

Sate

llite

C

omm

unic

atio

ns

Satellite C

omm

unications

Iridium Embedded SolutionIP Ceramic Pin Patch Range

The Taoglas Iridium IP.25 ceramic patch antenna is a low profile (4mm) small footprint antenna (25*25mm) designed for Iridium devices. It has been specifically designed to provide excellent coverage in the 1616.0 to 1626.5 MHz range.

This ceramic patch offers typical gain of 2dBi Gain at Zenith, the IP.25 patch antenna is right hand circularly polarized thus matching the characteristics of the actual signal itself.

These patches are mounted via pin and double-sided adhesive and have been selected as the optimal solutions for the customer device environment.

Model no:

IP.252.4~2.5GHz

Electrical Data

Frequency 1621MHzPeak Gain 2dBIcVSWR 1.5 MaxReturn loss ≤-21dBaxial Ratio 3dB MaxImpedance 50ΩPolarization RHCPop. Temp. -40°C~+85°C

Mounting Data

Dimensions 25*25*4mmGP Size 50*50mmPin 1.65+/-0.2mm

| 65Satellite Communications

Sate

llite

C

omm

unic

atio

ns

Satellite C

omm

unications

Iridium External SolutionsMagnetic and Bracket Mount Solutions for Iridium applications

Taoglas have developed a range of Iridium™ antennas for maritime, aeronautical, government/defense, public safety, utilities, oil/gas, mining, forestry, and transportation applications using the Iridium™ Satellite constellation.

The newly developed IMA.01 – Marine Antenna delivers exceptional reception performance for permanent in-building or marine applications. This antenna is designed for free-air operation, no ground plane required.

The IAA.01 is a Magnetic mount solution, which has been designed for land/mobile solutions. The magnetic mount allows for easy installation and removal between vehicles or assets.

Model no:

IAA.011621MHzMagnetic Mount IRIDIUM Antenna

Electrical Data

Frequency 1616Mhz~1626.5MhzPeak Gain 4dBic typ.VSWR 1.5 MaxBandwidth 15MHzImpedance 50ΩPolarization RHCPop. Temp. -40°C~+85°C

Mounting Data

Dimensions 40.5*38*12.3mmCable(Std)*: 1.2M RG-174Connector(Std)*: SMA(M)Mounting Magnetic Mount

Model no:

IMA.011621MHzIRIDIUM Marine Antenna

Electrical Data

Frequency 1616Mhz~1626.5MhzPeak Gain 4dBic typ.VSWR 1.5 MaxBandwidth 29MHzImpedance 50ΩPolarization RHCPop. Temp. -40°C~+85°C

Mounting Data

Dimensions 90*38*70mmCable(Std)*: 3M RG-58UConnector(Std)*: SMA(M)Mounting Wall Mount Bracket


66 | Satellite Communications

Sate

llite

C

omm

unic

atio

ns

Satellite C

omm

unications

Iridium-GPS Embedded SolutionCGIP Single Feed Iridium-GPS Ceramic Pin Patch Range

The Taoglas GPS/Iridium CGIP.25 ceramic patch antenna is a low profile (4mm) small footprint single feed antenna (25*25mm) designed for the Iridium combined Iridium/GPS module. It has been specifically designed to provide excellent coverage in the 1575.420 to 1626.5 MHz range.

This ceramic patch offers typical gain of 3.5dBi Gain for GPS and 4.0dBi Gain for Iridium at Zenith, the CGIP.25 patch an-tenna is right hand circularly polarized thus matching the characteristics of the actual signal itself, allowing for improved gain and also rejection of multi-path interference.

These patches are mounted via pin and double-sided adhesive. Taoglas offers a custom tuning service for the patch for a specific customer device and ground-plane mounting.

*Actual GPS/Iridium system performance on a device is a function of the overall system and design of the device, and environment where the device is used.Use of even a tuned patch or any antenna on a compromised device design or application will not guarantee good GPS/Iridium performance.

Model no:

CGIP.251575.42~1626.5MHzSingle Feed

Electrical Data

Frequency 1575.42~1626.5MHzPeak Gain Iridium: 4dBic typ.

GPS: 3.5dBic typ.VSWR 2.5 MaxReturn loss ≤-10dBImpedance 50ΩPolarization RHCPop. Temp. -40°C~+85°C

Mounting Data

Dimensions 25*25*4mmGP Size 70*70mmPin 1.65+/-0.2mm

All the antennas you need for M2M

| 67Satellite Communications

Sate

llite

C

omm

unic

atio

ns

Satellite C

omm

unications

All the antennas you need for M2M

68 | Accessories

Acc

esso

ries

Accessories

accessoriesCable assemblies

2. The RF connectors needed – or if you require a stripped end, the open/strip/tin dimensions

3. The length of cable needed - please mention if this length is to include the

connectors or not (our drawing will reflect the length excluding the connectors)

4. The orientation of the connectors to each other.

5. The quantity needed

We will provide a quotation based on your requirement and if you wish to proceed we will prepare a Mechanical drawing of the Assembly for Customer approval

Taoglas supply an extensive line of radio frequency (RF) coaxial connector adapters, for use in wireless telecommunications applications including Wi-Fi, PCS, radio, computer networks, test instruments and antenna devices

Custom cable assemblies are a speciality of ours, each device/application is different, which calls for a unique solution, please contact us any requirements/advice you have/need.

The information we need, to prepare a part number, drawing and quotation is:

1. The type of Coaxial cable required (sometimes this is determined by the connectors eg. Murata GSC – uses 0.81mm coaxial cable)

This drawing and its inherent design concepts are property of Taoglas. Not tobe copied or given to third parties without the written consent of Taoglas.

TW Design Centre

A ALL Initial Design Kiwi 2011/7/4

Name Material Finish QTY

SMA(F) Bulk Head ST Brass Gold 1

1

1

2 Black1.13 Coaxial Cable FEP Jacket

Heat Shrink Tube PE Black 1

1

4

5 GoldWasher Brass

13 GoldIPEX MHF1 Brass

16 GoldNut Brass

Connector SMA(F)Connector IPEX MHF1

NOTES:1.All material must be RoHS compliant.2.Open/short, insertion loss QC required.3.The connectors have a fixed orientation to each other.

Ø 0.81 Ø 1.13 RG-178 RG-174 CFD-200

| 69Accessories

Acc

esso

ries

Accessories

accessoriesCable assemblies

accessoriesReceptacles

Once the drawings have been approved, we can supply tested and approved custom samples within 2 weeks, and production lead-times are 3-4 weeks for most deliveries.

We offer high quality products, which we test 100% and we have rigorous QC procedures to ensure that our products are within approved specifications.

We can also offer competitive pricing and bundled solutions coupled with our antenna deliveries.

We offer receptacles for the highest performance cable connection. It is always recommended to use a receptacle connection rather than a solder connection for RF cables. We currently stock...

• IPEX MHFI, MHFII, MHF-HT (U.FL comp)• IPEX MHFIII (W.FL Comp)• IPEX MHF4 (HSC Comp)

These receptacles are supplied on tape and Reel

IPEX MHFI(U.FL comp)

70 | Accessories

Acc

esso

ries

Accessories

accessorieson Board Connectors

Taoglas supply on-board connectors for PCB mount, Edge Mount and also available PCB and Crimp Mount types. These connectors complement our receptacle range for integration on PCB boards. We stock the below common configurations for SMa/MMCX and MCX – if there is a configuration you need not on the list please feel free to contact us at your local area Sales office (see Page 7).

Edge Mount Connectors

PCB and Crimp Mount

Description Part number Photo Drawing

SMA straight Edge EMPCB.SMAFSTJ.B.HTMount PCB JACKGOLD


SMA straight Edge EMPCB.SMAFSTJ.C.HTMount PCB JACKNICKEL


MMCX straight Edge EM.PCB.MMCX.F.ST.JACK.HTMount PCB JACKGOLD


MCX R/A PCB PCB.MCX.F.RA.JACK.AHC.HTMount & CrimpJack for 1.13/1.32/1.37

| 71Accessories

Acc

esso

ries

Accessories


MMCX straight PCB PCB.MMCX.F.ST.JACK.HTMount JACKLeg Length 3mmGOLD

accessorieson Board Connectors


SMA straight PCB PCB.SMAFST.J.A.HTMount JACKLeg Length 2mmGOLD


SMA straight SMT PCB PCB.SMAFST.J.B.HTMount JACKLeg Length 1mmGOLD


SMA straight 2 Hole PCB.SMAFST.2H.A.HTPCB Mount receptacle JACKGOLD


SMA straight 2 Hole PCB.SMAFST.2H.B.HTPCB Mount receptacle JACKNickel


MMCX straight SMT PCB.MMCX.F.ST.SMT.JACK.HTPCB Mount JACK Leg Length 0.76mmGOLD

PCB Mount

Services72 |

Serv

ices

Services

ServicesService Packages

CEllUlaR SUPPoRT aGREEEMEnT - CSa Service Packages

Code: CSA-0ATitle: Introduction and support agreementDeliverables: Statement of Work (SOW) Proposal

Item: • Senior antenna engineer & manager support • PTCRB and/or carrier certification consultation • Device design file review, consultation and recommendations • SOW details the process to achieve the target specification for the wireless device and potential antenna solutions and costs

Location: Online/Conference CallTime: 1/2 day

Code: CSA-0BTitle: Feasibility Study (Optional for complex cases)Deliverables: Report

Item: • Test and/or simultate different antenna technologies, topologies and material • Antennas will be tested in dfferent locations / positions • Selection of the best solution will be based on overall performance and project targets (price, certification, performance etc)

Location: Taoglas USA, Ireland or TaiwanTime: 3 weeks

Code: CSA-1Title: Device (passive) Antenna TestingDeliverables: Report

Item: • Test existing antenna passive performance with network analysers and using Taoglas 3d anechoic chamber • Return Loss, VSWR, Average Gain, Efficiency, Peak Gain and Radiation Patterns

Location: Taoglas USA, Ireland or TaiwanTime: 2 day

Code: CSA-2ATitle: Device (active) TRP (Total Radiated Power) testing Deliverables: Report

Item: • Test in Taoglas 3D anechoic chamber - Full TRP (850/1900MHz) USA channel analysis. If fail consult with sales for custom solution

Location: Taoglas USA, Ireland or TaiwanTime: 2 day

Contact your local regional office to get a quote for these services.

Services | 73

Serv

ices

Services



Code: CSA-2BTitle: Device (active) TIS (Total Isotropic Sensitivity) testing Deliverables: Report

Item: • Test in Taoglas 3D anechoic chamber - Full TIS (850/1900MHz) USA channel analysis. If fail consult with Noise Control Division

Location: Taoglas USA or Taiwan Time: 2 day

Code: CSA-3ATitle: Device Radiated Spurious Emissions (RSE) Traffic Mode testingDeliverables: Report

Item: • Test in 3D RSE anechoic chamber Full RSE-Traffic Mode Analysis (required to be Global). If fail consult with Noise Control Division

Location: Taoglas USA or Taiwan Time: 2 days

Code: CSA-3BTitle: Device Radiated Spurious Emissions (RSE) Idle Mode testingDeliverables: Report

Item: • Test in 3D RSE anechoic chamber Full RSE-Idle Mode Analysis (required to be Global). If fail consult with Noise Control Division

Location: Taoglas USA or Taiwan Time: 3 days

Code: CSA-4ATitle: Existing Antenna Matching (circuit, position or cable routing etc)Deliverables: Report and prototypes

Item: • 1 tuned customer device board with extra antenna prototypes • Matching circuit diagram and values if relevant (or cable routing diagram, antenna position/mounting etc.) • Final antenna position and integration method • Return Loss, VSWR, Average Gain, Efficiency, Peak Gain, Radiation Patterns

Location: Taoglas USA or Taiwan Time: 2 weeks

Services74 |

Serv

ices

Services



Code: CSA-4BTitle: Custom Antenna Design (Passive device mode) Deliverables: Report and Prototypes

Item: • 5 custom antenna prototypes • Mechanical Drawing • Final antenna position and integration method • Return Loss, VSWR, Average Gain, Efficiency, Peak Gain, Radiation Patterns, TRP measurements


Code: CSA-5Title: Custom Antenna Design (Active device mode) Deliverables: Report and Prototypes as per CSA-4A

Item: • Device transmit strength optimization in 3d anechoic RF test chamber • Active device impedance mismatchcheck and correction if required


Services | 75

Serv

ices

Services


GPS SUPPoRT aGREEEMEnT - GSa Service Packages

Code: GSA-0ATitle: Initial ReviewDeliverables: Consultation

Item: • Review existing design • Evaluate existing layout performance • Advise on layout improvements and antenna and device design direction


Code: GSA-1Title: Existing Device Antenna TestingDeliverables: Report

Item: • Test existing antenna passive performance in 3D test chamber • Test existing antenna active gain and noise figure • Return Loss, Axial Ratio, Average Gain, Efficiency, Peak Gain, Radiation Patterns

Location: Taoglas TaiwanTime: 2 days

Code: GSA-2Title: Antenna Tuning and MatchingDeliverables: Report and samples

Item: • 5 tuned antenna prototypes • Device with retuned antenna on board • Matching circuit optimized for board • Optimized for Return Loss, Average Gain, Efficiency, Peak Gain

Location: Taoglas TaiwanTime: 2 weeks

Services76 |

Serv

ices

Services


ISM SUPPoRT aGREEEMEnT - ISa Service Packages

Code: ISA-0ATitle: Introduction and support agreementDeliverables: Statement of Work (SOW) and Proposal

Item: • Senior antenna engineer & manager support • Device design file review, consultation and recommendations • SOW details the process to achieve the target specification for the wireless device and potential antenna solutions and costs


Code: ISA-1Title: Existing Device Antenna TestingDeliverables: Report

Item: • Test existing antenna passive performance in 3D test chamber • Return Loss, Average Gain, Efficiency, Peak Gain, Radiation Patterns

Location: Taoglas San DiegoTime: 2 days

Code: ISA-2Title: Custom Antenna DesignDeliverables: Report and prototypes

Item: • 5 custom antenna prototypes • Mechanical Drawing • Final antenna position and integration method • Return Loss, VSWR, Average Gain, Efficiency, Peak Gain, Radiation Patterns

Location: Taoglas San DiegoTime: 2 weeks

Contact your local regional office to get a quote for these services.

Ireland

Phone: +353 53 9169500 Email: [email protected]

Taiwan

Phone: +886 3 4612001 Email: [email protected]

USa

Phone: +1 858 450 0888 Email: [email protected]

Mexico


Services | 77

Serv

ices

Services


noise Control Division (nCD) - location: Taoglas USA Inc (San Diego)

Introduction

As winning antenna providers, Taoglas have been involved in the success of many different M2M devices over the past ten years.

We have learned a lot about M2M applications and how to design RF systems and hardware that works.

Everyday we actually share that knowledge with you and help you make your design a success, quickly.

We want to extend or value by not just offering an antenna solution, but a fast track to high volume device production so we can all benefit.

What does the Noise Control Division (NCD) do?

In addition to our comprehensive range of antenna products and services Taoglas also offers additional solutions in the RF, and more specifically, noise control area.

This means eliminating (or suppresssing) noise or more importantly “in band” noise that may cause a performance compromise, or certification challenges.

When would I need the Taoglas NCD?

When you have challenges getting your device to market from a wireless functionality standpoint.Maybe you have reception, TIS or RSE issues. Taoglas NCD is required when you know the antenna is good

and the module is certified, but you can not find the reason why your device is not passing certification, or is not doing what it is supposed to do.

The problem is often inband noise, meaning you have emissions at the cellular frequencies being reradiated back into the cellular module. Obviously a great antenna makes the problem worse!

How can Taoglas NCD help?

Let’s not make the antenna worse and let’s make the device better! We have the equipment and experience to identify where the noise may be originating from and either eliminate the noise or prevent the noise from getting to the antenna. Identifying the source of the problem is the biggest challenge.

Taoglas NCD has the equipment, expertise and experience to help you design your product better and quicker.

What next?

Please consult with Taoglas NCD to see how we can help design your product better and get to production quicker!

Tel: +1 858 450 0888 and ask for NCD or Dermot O’SheaEmail: [email protected]

Services78 |

Serv

ices

Services

notes

Services | 79

Serv

ices

Services








Services80 |

Serv

ices

Services

IrelandUnit 7 Peare Campus, Moyne Business Park, Old Dublin Road, Enniscorthy, Co. Wexford, Ireland


TaiwanNo 25, Changchun 6th Rd, Zhongli City, Taoyuan County, 32064, Taiwan, ROC320 桃園縣中壢市長春六路 25號


USA8375 Camino Santa Fe, Suite A, San Diego, CA 92121 USA


MexicoMX S DE RL DE CV, Calle del Olivo 17202-14, Col, Rinconada Otay, Tijuana , B.C, 22457, México


ISO 9001:2008 certified

Documents

Ireland Taiwan Rd, Zhongli City, Taoyuan County, 32064 ......• Security (Alarms, tracking, remote monitoring) e.g. security camera manufacturers about Taoglas our products and services