Upload
budi-santony
View
461
Download
31
Embed Size (px)
Citation preview
12/20/12 JIS G3101 1995
1/3www.leonghuat.com/specifications/jis_g3101_1995.htm
日本标准
(Properties minima unless stated)
Grade
钢号
Steel Product
钢材产品
Chemical Composition 化学成份 %
maximum 最大
Yield Stress
屈服强度
N/mm2
Tensile Strength
抗拉强度
N/mm2
Thickness
mmThickness 厚度 t (mm)
C Mn P S t£16 16<t£40 t>40
SS 330
(SS 34)
Steel plates and sheets, coils,
flats and bars
- - 0.05 0.05 205 195 175 330 to 430 Steel plates and sheets, coils and flats
t£5
Steel plates and sheets, coils and flats
5<t£16
Steel plates and sheets, coils and flats
16<t£50
Steel plates and sheets, and flats
t>40
Steel bars t£25 in diameter, side or distance across flats
Steel bars t>25 in diameter, side or distance across flats
SS 400
(SS 41)
Steel plates and sheets, coils,
sections, flats and bars
- - 0.05 0.05 245 235 215 400 to 510 Steel plates and sheets, coils, flats and sections
t£5
Steel plates and sheets, coils, flats and sections
5<t£16
Steel plates and sheets, coils, flats and sections
16<t£50
Steel plates and sheets, flats and sections
t>40
Steel bars t£25 in diameter, side or distance across flats
Steel bars t>25 in diameter, side or distance across flats
SS 490
(SS 50)
Steel plates and sheets, coils,
sections, flats and bars
- - 0.05 0.05 285 275 255 490 to 610 Steel plates and sheets, coils, flats and sections
t£5
Steel plates and sheets, coils, flats and sections
5<t£16
Steel plates and sheets, coils, flats and sections
16<t£50
Steel plates and sheets, flats and sections
t>40
Steel bars t£25 in diameter, side or distance across flats
Steel bars t>25 in diameter, side or distance across flats
SS 540
(SS 55)
Steel plates and sheets, coils,
sections, and flats 40mm or
under in thickness and steel
bars 40mm or under in
diameter, side length or
distance across flats
0.30 1.60 0.04 0.04 400 390 - 540 Steel plates and sheets, coils, flats and sections
t£5
Steel plates and sheets, coils, flats and sections
5<t£16
Steel plates and sheets, coils, flats and sections
16<t£40
Steel bars t£25 in diameter, side or distance across flats
Steel bars t>25 in diameter, side or distance across flats
(Properties minima unless stated)
Grade
钢号
Applicable Products
有关产品
Thickness
厚度 t
mm
Chemical Composition 化学成份 %
C Si Mn P S
£16
SM400A Steel plate, coil, section andt£50 0.23 - 2.5xC min.1) 0.035 0.035 245
12/20/12 JIS G3101 1995
2/3www.leonghuat.com/specifications/jis_g3101_1995.htm
(SM41A) flat50<t£200 0.25 - 2.5xC min.1) 0.035 0.035 245
SM400B
(SM41B)
Steel plate, coil, section and
flat
t£50 0.20 0.35 0.60 to 1.40 0.035 0.035 245
50<t£200 0.22 0.35 0.60 to 1.40 0.035 0.035 245
SM400C Steel plate, coil and section t£100 0.18 0.35 1.40 0.035 0.035 245
SM490A
(SM50A)
Steel plate, coil, section and
flat
t£50 0.20 0.55 1.60 0.035 0.035 325
50<t£200 0.22 0.55 1.60 0.035 0.035 325
SM490B
(SM50B)
Steel plate, coil, section and
flat
t£50 0.18 0.55 1.60 0.035 0.035 325
50<t£200 0.20 0.55 1.60 0.035 0.035 325
SM490C Steel plate, coil and section t£100 0.18 0.55 1.60 0.035 0.035 325
SM490YA
(SM50YA) Steel plate, coil, section and
flat
t£100 0.20 0.55 1.60 0.035 0.035 365
SM490YB
(SM50YB)t£100 0.20 0.55 1.60 0.035 0.035 365
SM520B
(SM53B)
Steel plate, coil, section and
flatt£100 0.20 0.55 1.60 0.035 0.035 365
SM520C Steel plate, coil and section t£100 0.20 0.55 1.60 0.035 0.035 365
SM570 Steel plate, coil and section t£100 0.18 0.55 1.60 0.035 0.035 460
(Properties minima unless stated)
Grade
钢号
Thickness
厚度 tmm
Chemical Composition 化学成份 %
(Maximum 最大)Yield Stress
屈服强度
N/mm2Tensile
Strength
抗拉强度
N/mm2
Yield Ratio %
屈服率(Maximum 最大)
Elongation 伸长率 %
Charpy
Energy J at
0ºC (for
t>12 only)
冲击功C Si Mn P S
CEV4)
Test Piece No. 测试片号数
1A 1A 4
Thickness
厚度 t mmThickness 厚度 1)
t mm
Thickness 厚度1)
t mm
Thickness 厚度1)
t mm
£40 40£t£100 6£t<12 12£t<16 = 16 16<t£40 40<t£100 6£t<12 12£t<16 = 16 16<t£40 40<t£100 6£t£16 16£<t£50 40< t£100
SN400A 6£t£100 0.24 - - 0.05 0.05 - - 235 235 235 235 215
400 to
510
- - - - - 17 21 23 -
SN400B
6£t£50
CSW5) =0.260.20 0.35
0.6
to
1.4
0.03 0.015 0.36 0.36 2352352) to
355
2352) to
355235 to 355 215 to 355 - 803) 803) 80 80 18 22 24
27
(Test Piece
No.4 in
roll ing
direction)
50<t£100
CSW5) =0.260.22 0.35
0.6
to
1.4
0.03 0.015 0.36 0.36 2352352) to
355
2352) to
355235 to 355 215 to 355 - 803) 803) 80 80 18 22 24
SN400C
6£t£50
CSW5) =0.260.20 0.35
0.6
to
1.4
0.02 0.008 0.36 0.36 N.A. N.A.2352) to
355235 to 355 215 to 355 N.A. N.A. 803) 80 80 18 22 24
50<t£100
CSW5) =0.260.22 0.35
0.6
to
1.4
0.02 0.008 0.36 0.36 N.A. N.A.2352) to
355235 to 355 215 to 355 N.A. N.A. 803) 80 80 18 22 24
6£t£500.18 0.55 1.6 0.03 0.015 0.44 0.46 325
3252) to 3252) to325 to 445 295 to 415 - 803) 803) 80 80 17 21 23
12/20/12 JIS G3101 1995
3/3www.leonghuat.com/specifications/jis_g3101_1995.htm
SN490B CSW5) =0.29 445 445
490 to
610
50<t£100
CSW5) =0.290.20 0.55 1.6 0.03 0.015 0.44 0.46 325
3252) to
445
3252) to
445325 to 445 295 to 415 - 803) 803) 80 80 17 21 23
SN490C
6£t£50
CSW5) =0.290.18 0.55 1.6 0.02 0.008 0.44 0.46 N.A. N.A. 3252) to
445325 to 445 295 to 415 N.A. N.A. 803) 80 80 17 21 23
50<t£100
CSW5) =0.290.20 0.55 1.6 0.02 0.008 0.44 0.46 N.A. N.A.
3252) to
445325 to 445 295 to 415 N.A. N.A. 803) 80 80 17 21 23
Notes : 1), 2), 3), 4), 5) references shall be made to JIS Handbook, Ferrous Materials & Metallurgy II, 1998
(Properties minima unless stated)
Grade
钢号
Quality
品质
Thickness t
厚度mm
Chemical Composition 化学成份 %Tensile Strength1)
抗拉强度
N/mm2
Elongation
C Mn P S1.2£t<1.6 1.6£t<2.0 2.0£t<2.5
maximum 最大
SPHC Commercial 1.2£t£14 0.15 0.60 0.050 0.050 270 27 29 29
SPHD Drawing 1.2£t£14 0.10 0.50 0.040 0.040 270 30 32 33
SPHE Deep Drawing 1.2£t£6 0.10 0.50 0.03 0.035 270 31 33 35
Notes:1) The values specified for tensile strength, elongation and bendability shall not be applied to irregular portions of both ends of the steel coil.
(Properties minima unless stated)
Grade
钢号
Tensile2) Strength
抗拉强度 (min.最小)
N/mm2
Elongation 伸长率 % (minimum 最小)
Tensile Test Piece
抗拉测试片thickness 厚度 t (mm)
0.25£t<0.40 0.40£t<0.60 0.60£t<1.0 1.0£t<1.6 1.6£t<2.5 2.5£t
SPCC (270)1) (32)1) (34)1) (36)1) (37)1) (38)1) (39)1)
No.5 in roll ing direction
SPCD 270 34 36 38 39 40 41
SPCE3) 270 36 38 40 41 42 43
Notes :1) The tensile test value is not applicable to SPPC. When (SPCCT) is specified, values in parentheses shall be applied.
2) For those less than 0.60mm in thickness, the tensile test is omitted.
3) When the steel sheet and coil of standard tempered grade in quality SPCE are specified non-aging property (SPCEN), this shall be guaranteed for 6 months after shipment from the manufacturer's factory.