8/12/2019 Manual Extrusora
1/4
Thank you for your purchase, for any further questions regarding
the extruder, please
contact us by email 7 day a week at
[email protected].
!"#$" %&T"' I #( %&T )"$&%$I*!" +&)
#% -#(#"$ &) *&-I! I%/0) )"$0!TI%+)&( #$$"(*! &+
T1I$ 2IT, T1"$"
I%$T)03TI&%$ #)" &%! 0I-"!I%"$, !"#$"
T#2" 3#)" 41"% -"#!I% 4IT1 1&T
!#$TI3 #%- 4"#) )&") )&T"3TI5"
"#). #0") 4I!! "#$I! )"(&5" TI &+
+I%") 41"% I% &")#TI&%. -& %&T &")#T"
"6T)0-") 4IT1&0T $0")5I$I&%.
!"#$" -& %&T &")#T" "6T)0-") I%-&&)$.
!"#$" "%$0)" # +I)" "6TI%0I$1") I$ 4IT1I% )"#31 41"% &")#TI%
T1"
"6T)0-").
art ' #ssembly of +rame
3ongratulations on purchasing your new filament extruder, you
are 8ust a few
hours away from extruding your very own filament9
ou can begin by verifying that all parts are present in your kit
by reviewing the
parts list below, if your kit is missing any pieces, please
contact us 7 days a
week at [email protected].
:;#luminum %ipple :machined;
(1) steel pipe flanges
(2) 1/4 bolts 3" length steel high grade
(6) 1/4 nuts steel high grade
(1) 1.75mm Predrilled die
(1) 3mm Predrilled die
(1) 5/!" auger bit(mahined to si#e)
(1) 2.2 $P% &ear%otor 12'
(1) 12' Poer suppl
(2) *rushless omputer fan 12'
(2) %ahine sres for motor mounting
(1) P+, -emp. ontrol nit ith autotune
(1) -pe 0 -hermal ensor
(4) ire lamp
(1) steel oupler
(1) 'ariable 'oltage regulator for motor speed ontrol
(1) eat *and 12 %ia +nsulated
(1) haft oupler for motor to auger ouple
(1) opper (* *la)
(1) -hrust *earing
(1) olidtate$ela 25
(1) ightemp fiberglass insulation
(1) 128 plug
(1) able ties
ooden frame preut and predrilled
8/12/2019 Manual Extrusora
3/4
unit was shipped with a =v power supply, as the diagram
indicates a =Av.
$tep C' 1ot "nd
The hot end is what heat the pellets being pushed forward into a
pool of
plastic, which will be forced out through the noDDle by new
pellets being
pushed into the mixture.
*egin by securing the steel pipe coupler onto the end of the
pipe nipple.
$lide the heat band onto the steel coupler, it will be a tight
fit, you may need
to slightly stretch the heat band on, be careful not to
overstretch and
damage the internal mica of the heat band.
$crew the thermocouple onto the hot end,careful not to over
tighten.
3arefully install the fiberglass insulation :use proper hand
protection;, ou
may secure the insulation, by using the supplied cable ties.
$tep E' 4rapping it up
If you?ve come this far you should be proud, give yourself a pat
on the back.
ou will need to verify that all components are functioning
properly, plug in the
I- temp. control unit, after a few moments it should display
current temp. and target
temp.
lug in the heater power, heater should begin to heat up
almost
instantaneously.
+ilament will need to coil consistently on the floor for a
consistent product,
for best results,
