Matsui 1409r Tv Sm

8/18/2019 Matsui 1409r Tv Sm

1/29

This Manual is available in Electronic format.

SERVICE MANUAL

MATSUI 1409R/TTV

Version 1.0

Mastercare, Maylands Avenue, Hemel Hempstead, Hertfordshire, HP2 7TG, Telephone 01442 888104

Manual Number: 668502

8/18/2019 Matsui 1409r Tv Sm

2/29

MATSUI 1409R/TTV

PRODUCED BY

MASTERCARE TECHNICAL CENTRE

SERVICE MANUAL

Specifications are subject to change without notice.

COPYRIGHT © 2000 MASTERCARE LIMITED

8/18/2019 Matsui 1409r Tv Sm

3/29

SERVICING NOTICES ON CHECKING

6. AVOID AN X-RAY1. KEEP THE NOTICES

As for the places which need special attentions,they are indicated with the labels or seals on thecabinet, chassis and parts. Make sure to keep theindications and notices in the operation manual.

3. USE THE DESIGNATED PARTS

5. TAKE CARE TO DEAL WITH THE

CATHODE-RAY TUBE

Safety is secured against an X-ray by consider-ing about the cathode-ray tube and the highvoltage peripheral circuit, etc.Therefore, when repairing the high voltage pe-

ripheral circuit, use the designated parts andmake sure not modify the circuit.Repairing except indicates causes rising of highvoltage, and it emits an X-ray from the cathode-ray tube.

Please include the following informations when you order parts. (Particularly the VERSION LETTER.)1. MODEL NUMBER and VERSION LETTER

The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be found at the end of the SERIAL NUMBER.2. PART NO. and DESCRIPTION

You can find it in your SERVICE MANUAL.

HOW TO ORDER PARTS

Inferior silicon grease can damage IC's and transistors.When replacing an IC's or transistors, use only specified silicon grease (YG6260M).Remove all old silicon before applying new silicon.

IMPORTANT

2. AVOID AN ELECTRIC SHOCK

There is a high voltage part inside. Avoid anelectric shock while the electric current isflowing.

The parts in this equipment have the specificcharacters of incombustibility and withstandvoltage for safety. Therefore, the part which isreplaced should be used the part which hasthe same character.Especially as to the important parts for safetywhich is indicated in the circuit diagram or the

table of parts as a mark, the designatedparts must be used.

4. PUT PARTS AND WIRES IN THE

ORIGINAL POSITION AFTER

ASSEMBLING OR WIRING

There are parts which use the insulationmaterial such as a tube or tape for safety, orwhich are assembled in the condition thatthese do not contact with the printed board.The inside wiring is designed not to get closerto the pyrogenic parts and high voltage parts.Therefore, put these parts in the originalpositions.

In the condition that an explosion-proof cathode-ray tube is set in this equipment, safety issecured against implosion. However, whenremoving it or serving from backward, it isdangerous to give a shock. Take enough care todeal with it.

PERFORM A SAFETY CHECK AFTER

SERVICING

7.

Confirm that the screws, parts and wiring whichwere removed in order to service are put in theoriginal positions, or whether there are theportions which are deteriorated around theserviced places serviced or not. Check theinsulation between the antenna terminal or

external metal and the AC cord plug blades.And be sure the safety of that.

(INSULATION CHECK PROCEDURE)

1.2.

3.

4.

Unplug the plug from the AC outlet.Remove the antenna terminal on TV and turnon the TV.Insulation resistance between the cord plugterminals and the eternal exposure metal[Note 2] should be more than 1M ohm byusing the 500V insulation resistance meter[Note1] .If the insulation resistance is less than 1Mohm, the inspection repair should berequired.

[Note 1]

If you have not the 500V insulationresistance meter, use a Tester.

[Note 2]

External exposure metal: Antenna terminalEarphone jack

A1-1

8/18/2019 Matsui 1409r Tv Sm

4/29

CONTENTS

A2-1

SERVICING NOTICES ON CHECKING ...................................................................................................HOW TO ORDER PARTS ........................................................................................................................IMPORTANT .............................................................................................................................................CONTENTS ..............................................................................................................................................GENERAL SPECIFICATIONS .................................................................................................................DISASSEMBLY INSTRUCTIONS ............................................................................................................SERVICE MODE LIST ..............................................................................................................................CONFIRMATION OF USING HOURS ......................................................................................................NOTE FOR THE REPLACING OF MEMORY IC .....................................................................................ELECTRICAL ADJUSTMENTS ...............................................................................................................MAJOR COMPONENTS LOCATION GUIDE ..........................................................................................BLOCK DIAGRAM ...................................................................................................................................PRINTED CIRCUIT BOARDS

MAIN/CRT/T'TEXT...............................................................................................................................SCHEMATIC DIAGRAMS

MICON/TUNER....................................................................................................................................IF/CHROMA .........................................................................................................................................POWER ...............................................................................................................................................DEFLECTION/CRT..............................................................................................................................21PIN/SOUND .....................................................................................................................................VIDEO/RGB SW ..................................................................................................................................T'TEXT .................................................................................................................................................

WAVEFORMS ..........................................................................................................................................MECHANICAL EXPLODED VIEW ...........................................................................................................PARTS LIST .............................................................................................................................................

A1-1A1-1A1-1A2-1A3-1~A3-4B-1C-1C-1C-1D1-1~D2-1D3-1E-1, E-2

F-1~F-4

G-1, G-2G-3, G-4G-5, G-6G-7, G-8G-9, G-10G-11, G-12G-13, G-14H-1~H-3I-1NOT AVAILABLE

8/18/2019 Matsui 1409r Tv Sm

5/29

GENERAL SPECIFICATIONS

A3-1

G-1.Outline of the Product

14 inch(335.4mmV):Measured diagonally

Color CRT 90 degree deflection

G-2.Broadcasting System

U.K. System I

G-3.Color System NTSC PAL SECAM or Monochrome signal

G-4.NTSC Playback(PAL 60Hz) Yes No

G-5.NTSC 3.58+4.43/PAL60Hz Yes No

G-6.Antenna Input Impedance

VHF/UHF 75 ohm unbalanced

G-7.Tuner and Receiving Contactless Electric tuner 1Tuner System

2Tuner System

channel Tuner Oscar(W/O HYPER) Oscar(W/ HYPER)

France CATV) Others

cannel coverage 21~ 69

Tuning System

Frequency syn. Voltage syn. Others

G-8.Preset Channel 80 channels

G-9.Intermediate FrequencyPicture(fP) 39.5 MHz MHz MHzSound (fS) 33.5 MHz MHz MHzfP-fS 6.0 MHz MHz MHz

G-10.Stereo/Dual TV Sound

Yes( NICAM GERMAN USA JAPAN) No

G-11.Tuner Sound Muting Yes No

G-12.Power Source 230~240 V AC 50Hz AC 60Hz

G-13.Power Consumption: 44 W at AC 230 V 50 Hz

W at DC V

Stand by: 10 W at AC 230 V 50 Hz

Per Year: - kWh / Year

G-14.Dimensions(Approx.)

362.0 mm(W) 360.0 mm(D) 320.5 mm(H)

G-15.Weight(Approx.) Net: 9.5 kg ( - lbs)

Gross: 11.5 kg ( - lbs)

G-16.Cabinet Material

Cabinet Front: PS 94HB DECABROMABS 94V2 NON-DECA

94V0

Back Panel: PS 94HB DECABROMABS 94V2 NON-DECA

94V0

Jack Plate: PS 94HB DECABROMABS 94V2 NON-DECA

94V0

8/18/2019 Matsui 1409r Tv Sm

6/29


A3-2

G-17.Protector: Power Fuse

G-18.RegulationSafety

UL CSA SAA SI CE SEVBS NF NEMKO FEMKO DEMKO IEC65

SEMKO NZ HOMOLO SABS CNS SISIRNOM AS3159 DENTORI UNE GOST NONE

RadiationFCC DOC FTZ PTT CE SEVSABA SI NF NZ HOMOLO UNECNS CISPR13 DENTORI AS/NZS NONE

X-RadiationPTB DHHS HWC DENTORI NONE

G-19.Temperature

Operation 5 º C~ 40 ºC

Storage -20 ºC~ 60 ºC

G-20.Operating Humidity Less than 80 %RH

G-21.Clock and TimerSleep Timer Yes Max 120 Min.( 10 Min. Step) No

On/Off Timer Yes Programs No

Wake Up Timer Yes Programs No

G-22.Timer back up Time

More than - Minutes (at Power Off Mode)

G-23.Terminals

VHF/UHF Antenna Din Type F-Type France Type

Video Input(Front) (RCA ø8.3)

Video Input(Rear)(x ) (RCA ø8.3)

Video Output(Rear) (RCA ø8.3)

Audio Input(Front) (RCA ø8.3)Audio Input(Rear)(x ) (RCA ø8.3)

Audio Output(Rear) (RCA ø8.3)

21 Pin (x 1 ) DC Jack(Center +) Ear Phone Jack(ø3.5)

Head Phone Jack(ø3.5) AC Outlet Ext Speaker

Diversity S Input(Front) S Input(Rear)

G-24.IndicatorPower Stand By On Timer

( ) ( Red ) ( )

G-25.Display

On Screen Display

Menu

Clock Set( 12H 24H) System SelectOn/Off Timer Hotel Lock Area Code

CH Tuning Sound 1/2 NICAM Auto Off

Picture Guide CH Set Audio

Language CATV

Pin Code Registration

Control Level

Sound Brightness Contrast

Color Tint(NTSC Only) Sharpness

Tuning Bass Treble

Balance Back Light

Stereo,Audio Output,Bilingual Picture Menu AFT

Stereo,Audio Output,SAP Mid Night Theater Sound MuteStereo,Audio Output GAME Sleep Time

CH Clock Pin Code Hotel Lock Skip

8/18/2019 Matsui 1409r Tv Sm

7/29


A3-3

G-26.OSD Language

Eng Ger Fre Spa Ita Por Jpn

OSD Language Setting

Eng Ger Fre Spa Ita Por Jpn

Not ApplicableG-27.Speaker : Pos it ion Front Side Bottom

Size 3 inches

Imp 8 ohm x 1 pcs

Power Max 1.5 W

10% 1.0 W (Typical)

G-28.EXT Speaker

Yes W Imp ohm

G-29.Carton

Master Carton: Need No Need

Content: ---- Set

Material: ---- / ---- Corrugated Carton

Dimensions: ---- mm(W) ---- mm(D) ---- mm(H)

Description of Origin Yes No

Gift Box

Material Double/Brown Corrugated Carton ( with Photo Label)

Double/White Corrugated Carton ( with Photo Label)

Double Full Color Carton W/Photo

Dimensions: 440 mm(W) 408 mm(D) 380 mm(H)

Design: As Per BUYER 's

Description of Origin: Yes No

Drop Test Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces

Height 25cm 31cm 46cm 62cm 80cm

Container Stuffing: 866 Sets / 40' container

G-30.Accessories

Owner's Manual ( W/Guarantee Card) [ English ]

AC Plug Adapter Channel Film

Battery (UM- 4 x 2 ) Remote Control Unit

Safety Tip Toll Free Insert Sheet

Guarantee Card Audio-Video Cord (RCA)

Registration Card Warning Sheet

Quick Set-Up Sheet Schematic Diagram

Information Sheet U/V Mixer

75 ohm Coaxial Cable ( Single Shield Double Shield)

300 ohm to 75 ohm VHF Antenna Adaptor

21pin Cable Car Cord

Rod Antenna

One Pole Two Pole ( F-Type Din Type France Type)

Loop Antenna ( F-Type Din Type France Type)

G-31.Other Features

Auto Degauss Auto Search Full OSD

Auto Shut Off CH Allocation Premiere

Canal+ SAP Comb Filter

CATV Channel Lock Auto CH Memory

Anti-Theft Just Clock Function Hotel Lock

Rental Game Position Fastext

Unitext TopText Closed Caption

Picture Menu Mid Night Theater Memory(Last CH,Last Volume)

8/18/2019 Matsui 1409r Tv Sm

8/29


A3-4

G-32.Switch

Front

Power(Tact) Channel Up Volume Up

System Select Channel Down Volume Down

Main Power SW

Rear

AC/DC TV/CATV Selector

Degauss Main Power SW

G-33.Magnetic Field

BV : +0.45G BV : +0.35G BV : +0.25G

BH : 0.18G BH : 0.30G BH : 0.30G

BV : -0.15G BV : -0.25G BV : -0.50G

BH : 0.15G BH : 0.15G BH : 0.30G

G-34.Remote Control Unit: RC-DG

Glow in Dark Remcon Yes No

Power Source: D.C 3 V Battery UM - 4 x 2

Total 25 Key Power Quick View/Sub Page TV/AV

Stand By Status/Hold Bar Select

0/AV Quick View PAL/SECAM

1 Time Set Volume Up

2 Mute Volume Down

3 CH Skip CH Call

4 CH1/CH2 CH Down

5 Display Cancel CH Up

6 Text/Mix/TV CH Down/Page Down

7 Cancel/Display Cancel CH Up/Page Up

8 Cancel Page +/-

9 Store Program10 Skip/Reveal F/T/B

11 Sleep Hold

12 Skip List

Volume Up/ + Preset Rotate

Volume Down/ - Normal/ F/T/B Browse

0/10 Auto Memory Std/Auto

Tone 1/2/Reset Auto Memory

Info Call Band Select

Fine Tuning + Reset Search

TV/Caption/Text Menu Clock/Program

Normal/Expand Enter Clock/Set

Red Add Ch Set

Cyan/Fine Tuning + Delete Set +Normal Yellow/Fine Tuning- Set -

Color System Fine Tuning- Green

Wide Selecy Sub Page Nicam/Mono

Auto Wide On/Off Reset Tone 1/2(A/B)

Picture Position Navi FM Transmitter

Direct Change/Auto Search Back Light

Picture Menu Mid Night Theater

8/18/2019 Matsui 1409r Tv Sm

9/29

1. REMOVAL OF ANODE CAP

Read the following NOTED items before starting work.

After turning the power off there might still be a potential

voltage that is very dangerous. When removing the

Anode Cap, make sure to discharge the Anode Cap'spotential voltage.

Do not use pliers to loosen or tighten the Anode Cap

terminal, this may cause the spring to be damaged.

*

*

REMOVAL

1. Follow the steps as follows to discharge the Anode Cap.

(Refer to Fig. 1-1.)

Connect one end of an Alligator Clip to the metal part of a

flat-blade screwdriver and the other end to ground.

While holding the plastic part of the insulated Screwdriver,

touch the support of the Anode with the tip of the

Screwdriver.

A cracking noise will be heard as the voltage is discharged.

Flip up the sides of the Rubber Cap in the direction of thearrow and remove one side of the support.(Refer to Fig. 1-2.)

2.

DISASSEMBLY INSTRUCTIONS

GND on the CRT

Screwdriver

Alligator Clip

SupportCRT

GND on the CRT

Rubber Cap

CRTSupport

Fig. 1-1

Fig. 1-2

3. After one side is removed, pull in the opposite direction toremove the other.

NOTE

Take care not to damage the Rubber Cap.

INSTALLATION

1. Clean the spot where the cap was located with a smallamount of alcohol. (Refer to Fig. 1-3.)

B-1

Location of Anode Cap

Fig. 1-3

NOTE

Confirm that there is no dirt, dust, etc. at the spot wherethe cap was located.

2.

3.

Arrange the wire of the Anode Cap and make sure thewire is not twisted.

Turn over the Rubber Cap. (Refer to Fig. 1-4.)

Fig. 1-4

4. Insert one end of the Anode Support into the anode button,then the other as shown in Fig. 1-5.

5.6.

Confirm that the Support is securely connected.Put on the Rubber Cap without moving any parts.

CRTSupport

Fig. 1-5

8/18/2019 Matsui 1409r Tv Sm

10/29

INIT 00 83

0010CRT ON

ADDRESS DATA

SERVICE MODE LIST

This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.To enter the Service Mode, press both set key and remote control key for more than 1 second.

Set Key Remocon Key Operations

C-1

VOL. (-) MIN 1

VOL. (-) MIN 6

Initialization of the factory.NOTE: Do not use this for the normal servicing.

POWER ON total hours is displayed on the screen.Refer to the "CONFIRMATION OF USING HOURS".

Can be checked of the INITIAL DATA of MEMORY IC.Refer to the "NOTE FOR THE REPLACING OF MEMORY IC".

VOL. (-) MIN 7 Releasing of PROTECTION PASSWORD.

VOL. (-) MIN 8Writing of EEPROM initial data.NOTE: Do not use this for the normal servicing.

VOL. (-) MINDisplay of the Adjustment MENU on the screen.Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).

9

CONFIRMATION OF USING HOURS

POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.

1.2.

3.

Set the VOLUME to minimum.Press both VOL. DOWN button on the set and Channelbutton (6) on the remote control for more than 1 second.After the confirmation of using hours, turn off the power.

FIG. 1

Initial setting content of MEMORY IC.

POWER ON total hours. = (16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value)

+ (16 x tens digit value) + (ones digit value)

NOTE FOR THE REPLACING OF MEMORY IC

If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken toensure correct data settings while making reference to TABLE 1.

NOTE: No need the setting for the data except the Table 1.

ADDRESS DATA

1 00

2 00

3 004 00

5 10

6 28

ADDRESS DATA

7 C0

8 34

9 51A 00

B 00

C 80

ADDRESS DATA

D 00

E 03

F 0010 35

11 00

12 00

ADDRESS DATA

13 00

14 00

15 0016 00

21 4C

2E 06

1.2.3.4.

5.6.

7.8.9.The unit will now have the correct DATA for the new MEMORY IC.

Enter DATA SET mode by setting VOLUME to minimum.Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second.ADDRESS and DATA should appear as FIG 1.ADDRESS is now selected and should "blink". Using the VOL. UP or DOWN keys on the remote, step through theADDRESS until required ADDRESS to be changed is reached.Press ENTER to select DATA. When DATA is selected, it will "blink".Again, step through the DATA using VOL. UP or DOWN keys until required DATA value has been selected.

Pressing ENTER will take you back to ADDRESS for further selection if necessary.Repeat steps 4 to 7 until all data has been checked.When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.

Table 1

8/18/2019 Matsui 1409r Tv Sm

11/29

ELECTRICAL ADJUSTMENTS

1. BEFORE MAKING ELECTRICALADJUSTMENTS

•

•

•

•

Use an isolation transformer when performing anyservice on this chassis.Before removing the anode cap, discharge electricitybecause it contains high voltage.When removing a PCB or related component, afterunfastening or changing a wire, be sure to put the wireback in its original position.Inferior silicon grease can damage IC's and transistors.When replacing IC's and transistors, use only specifiedsilicon grease (YG6260M).Remove all old silicon before applying new silicon.

D1-1

Read and perform these adjustments when repairing thecircuits or replacing electrical parts or PCB assemblies.

CAUTION

Prepare the following measurement tools for electricaladjustments.

1. Synchro Scope2. Digital Voltmeter

On-Screen Display Adjustment

1. In the condition of NO indication on the screen.Press the VOL. DOWN button on the set and theChannel button (9) on the remote control for more than1 second to appear the adjustment mode on the screenas shown in Fig. 1-1.

Fig. 1-1

TV

00 OSD 15

2.

3.

Use the PROG/PAGE button or Channel button (0-9)on the remote control to select the options shown inFig. 1-2.Press the MENU button on the remote control to endthe adjustments.

FUNCTIONOSDCUT OFFRF.AGCVCO CENTH.POSI(50)V.POSI(50)V.SIZE(50)V.LINEAR(50)V.S CORR(50)G.DRVB.DRV

R.BIASG.BIASB.BIAS

NO.0001020304050607080910

111213

FUNCTIONBRICONTUNI COLTINTSHARPRGB CONTSUB COLB.B TINTR-Y BB-Y BLEVEL

STEREOT.MONOT.STE

NO.1415161718192021222324

252627

2. BASIC ADJUSTMENTS

Fig. 1-2

2-1: CONSTANT VOLTAGE

1.2.

3.4.5.

Place the set with Aging Test for more than 15 minutes.Using the remote control, set the brightness and

contrast to normal position.Connect the digital voltmeter to TP401.Set condition is AV MODE without signal.Adjust the VR501 until the DC voltage is 131.5 ± 0.5V.

2-2: VCO CENT

1.

2.

Activate the adjustment mode display of Fig. 1-1 andpress the channel button (03) on the remote control toselect "VCO CENT".Adjust the L201 until the "OK" appears on the screen.

1.

2.3.4.

5.

Place the set with Aging Test for more than 15 minutes.

Receive an 80dB monoscope pattern.Connect the digital voltmeter to pin 5 of CP101.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (02) on the remote control toselect "RF.AGC".Press the VOL. UP/DOWN button on the remote controluntil the digital voltmeter is 2.3 ± 0.05V.

2-3: AGC VOLTAGE

1.2.

3.

Place the set with Aging Test for more than 15 minutes.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (01) on the remote control toselect "CUT OFF".

Adjust the Screen Volume until a dim raster is obtained.

2-4: CUT OFF

2-5: WHITE BALANCE

NOTE: Adjust after performing CUT OFF adjustment.

1.2.

3.

4.

5.

6.

7.

8.

Place the set with Aging Test for more than 10 minutes.Receive the white 100% signal from the PatternGenerator.Using the remote control, set the brightness and contrastto normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (11) on the remote control toselect "R.BIAS".Using the VOL. UP/DOWN button on the remote control,

adjust the R.BIAS.Press the PROG/PAGE button on the remote control toselect the "G.DRIVE", "B.DRIVE", "G.BIAS" or "B.BIAS".Using the VOL. UP/DOWN button on the remote control,adjust the G.DRIVE, B.DRIVE, G.BIAS or B.BIAS.Perform the above adjustments 6 and 7 until the whitecolor is looked like a white.

2-6: FOCUS

1.2.3.

Receive an 80dB monoscope pattern.Turn the Focus Volume fully counterclockwise once.Adjust the Focus Volume until picture is distinct.

8/18/2019 Matsui 1409r Tv Sm

12/29


D1-2

1.2.

3.

4.

5.6.

Receive an 80dB monoscope pattern. (RF Input)Using the remote control, set the brightness andcontrast to normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (14) on the remote control toselect "BRI".Press the VOL. UP/DOWN button on the remotecontrol until the white 25% is starting to be visibleReceive the monoscope pattern. (Audio Video Input)Press the AV button on the remote control to set to theAV mode. Then perform the above adjustments 2~4.

2-7: BRIGHTNESS

2-8: HORIZONTAL POSITION

1.2.

3.

4.

5.

6.

Receive the monoscope pattern.Using the remote control, set the brightness andcontrast to normal position.Activate the adjustment mode display of Fig. 1-1 and

press the channel button (04) on the remote control toselect "H.POSI(50)".Press the VOL. UP/DOWN button on the remotecontrol until the SHIFT quantity of the OVER SCAN onright and left becomes minimum..Receive the monoscope pattern of NTSC. (Audio VideoInput)Press the AV button on the remote control to set to theAV mode. Then perform the above adjustments 2~4.

2-9: VERTICAL POSITION

1.2.

3.

4.

5.

6.

Receive the monoscope pattern.Using the remote control, set the brightness and

contrast to normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (05) on the remote control toselect "V.POSI(50)".Press the VOL. UP/DOWN button on the remotecontrol until the SHIFT quantity of the OVER SCAN onupside and downside becomes minimum..Receive the monoscope pattern of NTSC. (Audio VideoInput)Press the AV button on the remote control to set to theAV mode. Then perform the above adjustments 2~4.

2-10: VERTICAL SIZE

NOTE: Adjust after performing VERTICAL POSITIONadjustment.

1.

2.

3.

4.

5.

6.

7.

8.

9.

Receive the monoscope pattern.

Using the remote control, set the brightness andcontrast to normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (06) on the remote control toselect "V. SIZE(50)".Press the VOL. UP/DOWN button on the remotecontrol until the SHIFT quantity of the OVER SCAN onupside and downside becomes 8 ± 2%.Receive the monoscope pattern of NTSC. (Audio VideoInput)Press the AV button on the remote control to set to theAV mode.Using the remote control, set the brightness andcontrast to normal position.

Activate the adjustment mode display of Fig. 1-1 andpress the channel button (06) on the remote control toselect "V. SIZE(50)".Press the VOL. UP/DOWN button on the remotecontrol until the SHIFT quantity of the OVER SCAN onupside and downside becomes 10 ± 2%.

2-11: OSD HORIZONTAL

1.2.

Activate the adjustment mode display of Fig. 1-1.Press the VOL. UP/DOWN button on the remotecontrol until the difference of A and B becomesminimum. (Refer to Fig. 2-1)

BA

TV

00 OSD 15

Fig. 2-1

8/18/2019 Matsui 1409r Tv Sm

13/29


3.

1.

2.

3.

1.

2.

3.

4.

5.

6.

7.

8.

3-2: PURITY

NOTEAdjust after performing adjustments in section 3-1.

1.

2.

3.

4.5.

Receive the green raster pattern from color bargenerator.Adjust the pair of purity magnets to center thecolor on the screen.Adjust the pair of purity magnets so the color at theends are equally wide.Move the deflection yoke backward (to neck side)slowly, and stop it at the position when the wholescreen is green.Confirm red and blue colors.Adjust the slant of the deflection yoke while watching the

screen, then tighten the fixing screw.

DEFLECTION YOKE

DEFLECTION YOKE SCREW

MAGNET SCREW

PURITY MAGNETS

6 POLE MAGNETS4 POLE MAGNETS

Fig. 3-1

PURITY AND CONVERGENCEADJUSTMENTS

NOTE

NOTE

3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT)

Tighten the screw for the magnet. Refer to the adjustedCRT for the position. (Refer to Fig. 3-1)If the deflection yoke and magnet are in one body,untighten the screw for the body.Receive the green raster pattern from the color bargenerator.Slide the deflection yoke until it touches the funnel

side of the CRT.Adjust center of screen to green, with red and blue on thesides, using the pair of purity magnets.Switch the color bar generator from the green rasterpattern to the crosshatch pattern.Combine red and blue of the 3 color crosshatch patternon the center of the screen by adjusting the pair of4 pole magnets.Combine red/blue (magenta) and green by adjusting thepair of 6 pole magnets.Adjust the crosshatch pattern to change to whiteby repeating steps 6 and 7.

Turn the unit on and let it warm up for at least 30minutes before performing the following adjustments.Place the CRT surface facing east or west to reduce theterrestrial magnetism.Turn ON the unit and demagnetize with a Degauss Coil.

Adjust after performing adjustments in section 3-2.

3-3: STATIC CONVERGENCE

1.

2.

3.

3-4: DYNAMIC CONVERGENCE

NOTE

Adjust after performing adjustments in section 3-3.

1.

2.

Adjust the differences around the screen by movingthe deflection yoke upward/downward and right/left.(Refer to Fig. 3-2-a)

Insert three wedges between the deflection yoke andCRT funnel to fix the deflection yoke.(Refer to Fig. 3-2-b)

R G B

RGB

Fig. 3-2-a

WEDGE WEDGE

WEDGE

WEDGE POSITION

Fig. 3-2-b

R G B

RGB

UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT

Receive the crosshatch pattern from the color bargenerator.Combine red and blue of the 3 color crosshatch patternon the center of the screen by adjusting the pair of4 pole magnets.Combine red/blue (magenta) and green by adjusting thepair of 6 pole magnets.

D2-1

8/18/2019 Matsui 1409r Tv Sm

14/29

MAJOR COMPONENTS LOCATION GUIDE

D3-1

CP101

FB401

FOCUS VOLUMESCREEN VOLUME

TP401TU001

MAIN

J352

T502

VR501

L201

IC201

8/18/2019 Matsui 1409r Tv Sm

15/29

8/18/2019 Matsui 1409r Tv Sm

16/29

C P 8 0 2 B

L801

J 8 0 1

CP801

CP806

T P 0 2 4 TP022

TP023

C801

SW501

T U 0 0 1

CP501

F501 FFH502

C 4 3 9

D 0 0 1

D 7 0 6

C 0 0 2

C 7 0 2

L 7 0 2

L 7 0 1

C 6 0 4

C 6 0 3

C 6 0 2

W 8 0 9

L 7 5 3

IC351

C 3 5 7

C 5 1 6

C 5 0 6

L101

IC103

X101

D 1 0 4

D 1 0 5

IC199

R 1 2 6

I C 5 0 1

D103

J705

PH001

W088

D 5 0 5

W038

SW104SW102SW107SW106

CP101

R003

R004

R 7 1 0

C 5 0 5

R 1 2 8

W037

W086

R 1 1 4

W 0 7 8 C 1

0 3

C 1 1 1

Q701

R 7 5 6

W 0 8 3

R

1 3 1

C350

CC004

W087

C 0 0 3

C 5 2 1

R107

C 3 5 1

C 3 5 3

FB401

C 4 3

5

C511_1

R 5 0 4

C406

C 4 4 8

C 4 0 3

R518

VR501

C 5 1 2 _1

D506

C 5 0 1

R 5 0 9

D507R 5 0 8

Q502

R 5 0 6

C 5 0 9

D 5 0 9

B 5 0 1

R 4 2 9

D 4 1 0

D405

C420

R403

C 5 2 6

IC506

C5 0 7

D528

D513

B 5 0 4

C517

C 5 1 9

C 5 1 5

R 5 1 6

CP351

D615

C 3 5 6

R 3 5 7

W 0 7 7

B 3 5 1

W 0 5 5 W

0 7 9

R 1 0 1

C 1 0 2

W090

C223

C217

X601

L201

C 2 0 2

L203

C F 2 0 1

CF204

R212

IC201

L202

C 2 0 5

C 2 1 0

C209

W093

C 2 1 9

C631

C 6 2 3

C625C620C615

C605

CF203

CF202

L204

C201

W 0 8 0

C 2 1 3

W 0 9 7

W897

W 0 1 3

C 4 4 0

R446

R427

D 4 0 4

C 4 0 7

R 4 4 5

R 4

2 1

C 4 4 6

T401

TP401

W 8 1 3

C 4 3 0 R410

C 4 2 5

D 4 0 3

C414

C 4 1 0

C 5 1 0

L 6 0 3

CP401

W063

R406

R 5 0 5

D516

C520

C 5 2 2

Q503

C 5 2 7

R 5 2 2

R 0 0 1

R 0 0 2

Q504

I C 5 0 2

C 5 2 4

C 5 2 5

D 5 1 9

D 5 2 1

C 5 2 3

D 5 2 0

C 6 3 5

R 5 1 4

R 4 0 4

W 0 9 9

L 7

0 3

W092

W094

W 8 1 4

C 3 5 2

L602

T502

C 0 0 1

L 0 0 1

W811

C 6 1 9

C 6 1 7

C 6 1 8

R 3 5 5

R 1 0 2

W 0 8 9

W

1 0 4

C216

D510

R 4 1 5

W068

W022

R 5 2 0

W052

D512

L 5 0 1

W 0 0 6

W009

W034

W035

W036

R 1 2 4

Q507

R 4 2 2

W051

W053

W076

Q506

R 1 0 4

D518

W054

W

1 0 3

W1 0 2

R 5 2 3

D 5 1 5

R408

W 8 1 2

W024

W 0 2 1

R 4 1 4

W046

W 0

1 6

W 0 4 3 W

0 4 1

W 0 5 0

W 0 4 7

L206

W 0 7 3

W020

C 6 0 9

Q401_1

R515

C 6 2 2

W091

C621

W039

W 8 2 4

W 0 5 9

W082

HS401

I C 4 0 1

W 0 2 5

CP802A

C 4 0 9

W007

W 0 0 8

R 4 0 7

W 0 2 9

D406

R 4 1 7

R 4 1 8

D407

R 6 2 4

W 0 6 7

W010

W101

C 2 2 1

W 0 6 6

W801

W 8 6 1

C 3 5 9

C 7 0 8 _1

C 7 5 9

C 1 0 1

R 8 0 7

R 8 0 3

R 8 0 5

R802

R804

W106

W105

R 8 0 6

W111

W110

R 5 1 0

R 5 1 1

W 0 0 1

W107

W 0 0 5

D508

W 0 2 3

R 6 0 9

B 2 0 1

R 1 4 1

R602

W1 1 2

W062

C 6 4 0

D614

W 0 7 2

W 0 7 1

W061

W113

W 0 6 0

W064

R146

C 1 0 6

W056

W 0 7 5

W074

W017

W1 1 4

W 0 4 4 W040

W 0 4 5

W 0 4 9

C 6 4 2

C 6 4 1

Q612

C 5 3 1

W033

W027

D 6 1 1

W 0 6 5

W058

W

1 1 5

W 8 0 8

C 5 0 8

D 5 1 4

W014

W015

W 0 1 9

W031

W 0 1 8

W1 1 7

Q803

Q801

Q802

Q402

C110

W 0 1 2

W 0

7 0

D 5 1 1

W 0 2 6

C 5 0 4

C 4 0 5

C 4 1 8

C 8 1 9

C 4 4 3 C 4

3 7

R816

C 6 3 4

D602

D604

D 6 0 3

W028

R 6 2 3

C 8 0 2

D 8 0 1

D 8 0 2

W118

W 0 1 1

W1 1 9

C 6 2 6

W810

W 8 2 7

W 8 0 4

W 8 1 6

W 8 0 2

W 8 2 8

W 8 1 5

W 8 2 1

W 8 2 6

J201

W 0 9 8

CD802

PRINTED CIRCUIT BOARDSMAIN/CRT (INSERTED PARTS)

SOLDER SIDE

F-1

8/18/2019 Matsui 1409r Tv Sm

17/29

F-3

12

23

34

1 C 8 0 5

R 8 1 1

C 8 0 4

R 8 0 9

C 8 0 6

R 8 1 4

R 8 1 3

C 0 0 5

C 0 0 4

R 7 0 8

R 7 1 5

R712

C 7 0 4

C 7 0 3

R 7 1 1

R705 R 7 0 6

R 7 0 4

R 7 2 1

R 7 1 7

C 7 0 7

R 7 2 3

Q702

R 7 2 2

R601

Q351

C 7 0 5

R 5 2 1

R 1 1 8

R 1 1 7

C 1 1 4

C 1 1 3

Q102 R 1 3 0

R 1 3 2

R 1 1 9

C 1 1 5

R 1 2 9

Q101 R 1 2 0

C 1 0 4

R 1 3 3

R 1 3 4

C108 R 1 2 5

R 1 3 6

R122

IC101

R 1 1 1R103

R110

R 1 0 9

R 1 3 9

R 1 0 6

C 1 0 7

R115

R 3 5 4

R757

R 5 0 7

C 1 0 5

R 1 4 2

R 3 5 0

C 0 0 6

R633

R631

R 6 3 4

C 3 6 0

R 1 3 8

R 1 4 0

R352

R 5 1 2

R513

C513

R 1 0 8

C112

R 1 1 6

R 1 2 1

R 6 1 5

C 6 2 4

R 6 1 8

C 6 3 0

C 6 1 2

C 6 1 3

R 2 1 1

C 6 1 0

C 2 1 8

R213 C 2 0 3

C212R217

C215

R 2 1 5

Q204 R 2 1 6

R 2 1 4

C 2 0 4

C214

C 2 0 6

C 2 1 1

C611

R616R617

C 6 2 8

C629

R 6 2 6

R625

C 6 1 6

C 2 2 2

C 6 1 4

R612

R 6 1 3

R

6 1 4

R630

C 2 0 8

R 2 0 7

Q202

R 2 0 8

R209

R 2 1 0

R 2 0 5

C 2 0 7

R 2 0 3

R 2 0 1

R 2 1 8

Q601

R605

R 6 0 3

C 4 2 9

R405

R 5 2 4

C 6 2 7

R 6 2 1

R 6 2 2

R 5 2 5

R 1 1 3

C 6 3 2

C 6 3 3

R 6 3 9

R 6 3 8

R637

Q603

R356

R 2 0 6

R 2 0 2

Q505

R 0 0 6

C 6 3 7

Q203

Q201

R 3 5 9

R358

R 4 0 1

R 4 2 4

R 4 1 1

R519

C404

R 6 2 7

Q602

Q608 Q610 Q609

R 2 2 1

R640

R642

R641

R409

R 7 0 1

IC601

Q604

R 1 2 7

C 4 1 1

C 3 5 4

R 6 3 5

Q611

C 4 0 1

R 2 0 4

R 6 2 8

C638

Q103

R147

R 1 4 8

C 1 1 8

R 1 4 9

R611

Q703

Q704

R 7 1 8

R720

R 7 1 9

C 7 0 6

C227

R 4 2 0

R815

C639

W 8 0 6

C117

MAIN/CRT (CHIP MOUNTED PARTS)SOLDER SIDE

PRINTED CIRCUIT BOARDS

8/18/2019 Matsui 1409r Tv Sm

18/29

A B C D E F

A B C D E F

2

1

3

4

5

6

7

8

Q1012SC2412K

V-BUFFERQ1022SC2412K

H-BUFFER

D 0 0 1

H Z 3 0 - 3

L

G N D

B +

V o u

t

OS101

PIC-28143SY-2

1 2 3

R 1 3 8

6 8 K

R101

2.2K 1/4W

R 1 2 4

1 0 0 1 / 4 W

R 1 1 3

1 0 0

R 1 2 6

4 7 1 / 4 W

R 1 1 6

1 0 K

R 1 2 2

3 . 3

K

R106

2.2K

R139

1.2K

R103

820

R 1 4 2

4 . 7

K

R102

3901/4W

R 1 2 1

3 . 3

K

R 1 3 0

8 2 0

R 1 2 7 1

K

R111

4.7K

R 1 3 1

1 0 K 1 / 4 W

R 1 3 2

1 5 K

R 1 3 3

1 0 K

R109

10K R110

22K

R 118 100

R120

100

R 119 100

R 1 2 5

2 2 K

R 117 100

R 1 3 6

2 2 K

R10410K 1/4W

R114

2701/4W

R140

270

R 1 1 5

1 0 K

R146

470 1/4W

R147

560K R148

47K

R 1 4 9

5 6 K

R108

10K

R107 1001/4W

R 0 0 1

6 8 K

1 / 2 W

R 0 0 3

2 7 0 1 / 4 W

R 0 0 2

6 8 K

1 / 2 W

R 0 0 4

2 7 0 1 / 4 W

R 0 0 6

1 5 K

R 1 2 8

3 3 K 1 / 4 W

R 1 2 9

2 . 2

K

R 1 4 1

1 0 K 1 / 4 W

IC103

RES

1 2

C 1 0 3

1 0

2 5 V

K A

50

C 1 1 8 5 6 P C H

C112

0.01 B

C 1 0 7

0 . 0

1 B

C104

12P CH

C108

0.1 B

C105

12P CH

C 1 1 3

2 7 0 P

C H

C 1 1 4

2 7 0 P

C H

C 1 1 5

2 7 0 P

C H

C 1 1 7

5 6 0 P C H

C 0 0 1

0 . 0

2 2 M

C 0 0 4

2 2 0 P B

C 0 0 5

2 2 0 P B

C 1 1 0

0 . 1

F

5 . 5

V

C 1 1 1

3 3

6 . 3

V

K A

C101

1006.3V YK

C 1 0 2

4 . 7

5 0 V

K A

C106

150V KA

C 0 0 2

4 7 0

6 . 3

V

Y K

TU001 NJH3023M218

1 1 0 1

1

1 2

1 3

1 4

1 5

2 3 4 5 6 7 8 9

S W 1 0 6

S K H V B E D 0 1 0

C H U P

S W 1 0 7

S K H V B E D 0 1 0

C H D O W N

S W 1 0 2

S K H V B E D 0 1 0

V O L U P

S W 1 0 4

S K H V B E D 0 1 0

V O L D O W N

OF PRINTING AND SUBJ ECT TO CHANGE WITHOUT NOTICENOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME THE DC VOLTAGE AT EACH PART WAS MEASURED

WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST

WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.

NOTE:

L 1 0 1

3 3 u

H

L 0 0 1

1 0 u

H

TM101R25-1442

ANT001

TU-33AP

BT002

R03(AB)E_20_T

BT001

R03(AB)E_20_T

CC004 TP-IS-05

D107

SLR-342VCT32

STAND BY

X101

CSTS0800MG03-T2 1

2

3

D103

1SS133

I C 1 9 9 S - 2

4 C 0 4 B D P - L

A

M E M O R Y

1234

5 6 7 8

CP101W-D2506#01

1

2

3

4

5

6

IC101OEC6058A

MICON

1

1 0

1 1

12 13 14 15 16 17 18 19

2

20 21 22

2 3

2 4

2 5

2 6

2 7

2 8

2 9

3

3 0

3 1

3 2

3 3

343536373839

4

4041424344

5

6

7

8

9

Q103

2SA1037AK

SYNC SEPA

R.OUT

TUNER_AGC

TUNER_IF

SYNC_VIDEO

SDA

SCL

AFT

OSD-R

OSD-G

OSD-B

OSD-Y

TUNER_H

FOR_VCR

A_MUTE

OSD-R

OSD-G

OSD-B

OSD-Y

G-1

S D A

V C C

S C L

M O D E

FROM/TO 21PIN/SOUND

FROM/TO VIDEO/RBG SW

FROM/TO IF/CHROMA

TEST POINT

(MAIN PCB)MICON/TUNER SCHEMATIC DIAGRAM

NC

NC

4.84.80

0

0

4.8

0

21

54

3

5.0 0

5.0

0000

0

0 0 0

0

0

2.0

5.03.84.05.0

3.80.5 2.5 000000

0

0

0

0

0

5.0

5.0

5.0

5.0

2.7

4.8

5.0

2.4

5.0

5.0

4.9

NC2.65.0

3.84.0

5.0

5.0

5.0

5.0NC

4.9

NCNC

G N D

V C C

E 0

E 1

E 2

V S S

N C

14 ON TIME LED

13 STAND BY LED

12 9V POWER

NC

43 AKB WHITE

NC

22 H-SYNC

21 OSD Y 44 POWER

35 SCL

34 SOUND B

V D D

V S S

P A L / S E C

S D A

1 2 C O F F

O S D B

O S D R

O S D G

V S S

SOUND A

SD

REMORT

P_FAIL

RESET

XOUT

XIN

TEST

OSC OUT

OSC IN

V-SYNCFORTHED VCR

AFT

KEY

ATS

AV2

AV1

DEGAUSS

BLUE BACK H

A_MUTE

T_RESET

3 . 5

8 N T S C

NC

NC0

9.1

8.5

2.1

7

R.OUT

AGC

I2C OFF

I2C SDA

GND

I2C SCL

0 2

. 2 3

. 8 4

. 0 4

. 9 3 0

. 7 NCNCNCNCNC

A G C

A D R E S

S C L

S D A

V . S

B P L

B T L

I F

8/18/2019 Matsui 1409r Tv Sm

19/29

A B C D E F

A B C D E F

2

1

3

4

5

6

7

8

IS NON POLAR ONE. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP THE RESISTOR MARKED F IS FUSE RESISTOR.NOTE:

W 8 1 0

W 8 1 6

W806

W811

D 6 1 4

1 1 E 1 N

D615

1SS133

R 6 2 4

5 . 6

K + - 1

%

B 2 0 1

B L 0 2 R N 2 - R

6 2 T 4

L602

100uH

L603

100uH

I C 2 0 1

T B 1 2 5 4 N

C H R O M A

1 10 11 12 13 14 15 16 17 18 192 20 21 22 23 24 25 26 27 28

29

3

30313233343536373839

4

40414243444546474849

5

50515253545556

6 7 8 9

CF202

SFE6.0MB

C F 2 0 3

T P S 6

. 0 M B

OUTOUTGININ

CF201SAF39.5MZK220ZL

SAW FILTER

1 2 3 4 5

X 6 0 1

4 . 4

3 3 6 1 9 M H z

C 6 2 1

0 . 2

2

5 0 V

K A N P

L201

360K044

1 2 3

4 6

C F 2 0 4

M K T 4 1

. 5 M A 1 1 0 P

Q202

2SC2412K

T.V.Buf.

Q608

2SC2412K

OSD RED OUT

Q609

2SC2412K

OSD GREEN OUT

Q610

2SC2412K

OSD BLUE OUT

Q2042SC2814

IF Pre. AMP

Q2012SC2412K

EXT AUDIO DRV.

D 6 0 2

M T Z J 6

. 8 B

D 6 0 3

M T Z J 6

. 8 B

D 6 0 4

R 2 2 1

1 K

R 6 2 8

1 0 K

R

2 1 5

6

. 8 K

R 2 1 4

2 . 2

K

R 2 1 3

1 0 0

R203

100

R 2 0 8

2 . 2

K

R 2 0 7

3 . 3

K

R 2 0 5

5 6 0

R 2 0 4

5 6 0

R 2 0 1 1

0

R 2 0 2 1

K

R 2 1 6

4 7

R 2 1 2 7

5 1 / 4 W

R 2 1 7

1

. 2 K

R 6 0 2

3 3 K

1 / 4 W

R 2 1 8

1 0 0

R 6 1 5

2 . 2

K

R 6 3 7 2

. 7 K

R 6 3 8

2 . 7

K

R 6 3 9

2 . 7

K

R 6 1 6

1 0 0

R 6 1 7

1 0 0

R 6 1 8

1 0 0

R206

330

R 2 1 0 1

K

R 2 0 9

3 3 0

R 2 1 1

1 5 0

R 6 2 3

3 9 0 1 / 4 W

R 6 2 5

1 8 K

R 6 2 6

8 . 2

K

R 6 1 2

1 K

R 6 2 1

1 0 0

R 6 2 2

1 0 0

R630

270

R614

2.2K

R 6 1 3 1

K

C 6 0 9 0

. 2 2

5 0 V

K A

C 2 2 3

0 . 4

7

5 0 V

K A

C 2 1 6

4 . 7

5 0 V

Y K

C 2 1 7

1 0

1 6 V

K A

C 6 4 0

1 0

5 0 V

K A

C 2 1 9

2 . 2

5 0 V

K A

C 2 2 1

1

5 0 V

K A

C 6 1 5

1

5 0 V

K A

C 2 0 9

2 2

6 . 3

V

K A

C 2 0 5

1 0 0 0

1 0 V

Y K

C 2 0 2

1 0 0

1 6 V

Y K

C 6 0 5

1

5 0 V

K A

C 6 3 1

0 . 2

2

5 0 V

K A C

6 2 0

1

5 0 V

K A

C 6 2 5

1

5 0 V

K A

C 6 2 3

1 0

5 0 V

Y K C

6 4 1

1 0 0

6 . 3

V

Y K

C 6 3 5

1 0 0

1 6 V

Y K

C 6 3 4

1 0 0

1 6 V

Y K

C210

1006.3V YK

C 6 2 8

_ 1

0 . 0

0 2 2 B

C 6 1 1

1 0 P C H

C 6 1 7

0 . 1

F

C 6 1 8

0 . 1

F

C 6 1 9

0 . 1

F C 2 1 8

0 . 0

1

B

C 6 1 0

_ 1

0 . 0

0 2 2 B

C211

0.01 B

C 6 3 0

0 . 0

0 8 2 B

C 6 1 3

0 . 1

F

C 6 1 4

0 . 1

F C 2 2 2

_ 1

0 . 0

0 1

B

C 2 0 8

0 . 1

B

C 2 0 7

0 . 0

1 B

C 6 2 7

0 . 0

1 B

C 6 2 9

0 . 1

B

C 6 1 2

0 . 0

1 B

C 2 1 5

0 . 0

1 B

C 2 2 7

0 . 0

1 B

C 6 3 8

_ 1

C 6 3 9

0 . 1

F

C 6 3 7

_ 1

0 . 0

0 1

B

C 6 2 6

0 . 4

7 T F

C214

10P CH C 2 1 3

0 . 0

1

M

C212_1

0.001 BC204

0.022 B

C 2 0 3

0 . 0

2 2

B

C 2 0 1

0 . 0

1

M

C633

220P B

C 6 2 2

0 . 1

F

C 6 1 6

0 . 1

F

C632

220P B

C 6 2 4

0 . 0

1 B

C 2 0 6

0 . 0

1 B

OF PRINTING AND SUBJ ECT TO CHANGE WITHOUT NOTICENOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME THE DC VOLTAGE AT EACH PA

WITH THE DIGITAL TESTER WH

WAS RECEIVED IN GOOD CON

NOTE:

L206

0.33uH L 2 0 3

2

. 2 u

H

L 2 0 4

1 8 u

H

L202

12uH

Q203

2SA1037AK

T.V.DR.

Q604

2SA1037AK

VIDEO BUF.

A F T

S C L

A F C

S D A

H_

O U T

A V

_ A U D I O

A V

_ V I D E O

S Y N C

_ V I D E O

T U

_ V I D E O

_ O U T

TU_VIDEO_OUT

AV_VIDEO

AV_AUDIO

TU_AUDIO_OUT

AUDIO_OUT

P.CON+9V

P.CON+5V

GND

T

U N E R

_ A G C

A - Y

A - R

A - G

A - B TUNER_IF

FROM/TO POWER

G-3

(MAIN PCB)IF/CHROMA SCHEMATIC DIAGRAM

E X A U D I O

D C H F

P I F t a n

k

T V I N

L O O P F I L T E R

E X T I N

C b I N

C r

I N C I N

M O N O U T

Y I N

S Y N C I N

S D A

S C L

D l g G N D

H .

O U T

H V c c

( 9 V )

F B P I N /

S C P O U T

H . A

F C F i l t e r

B L A C K D a t

I F V c c

R I P P L E F I L

A U D I O O U T

I F G N D

I F I N

I F I N

I F A G C

A P C F i l t e r

X ’ t a l

C M O U T

R G B V c c

( 9 V )

E X T

. R I N

E X T

. G I N

E X T

. B I N

Y / C G N D

R O U T

G O U T

B O U T

1 K I N

V R A M P

V N F B

V O U T

r e f R

A B C L I N

S I F O U T

S I F I N

R F A G C

H C O R R E C T I O N

S I F I N /

A F T O U T

I F D E T O U T

P I F t a n

k

D E A M P

N C

Y / C V C O ( 5 V )

D C R e a

t e r

D l g V C O

4.9 3.8 8.4 3.7 0 1.3 0.2 0 1.9 2.73.1

3.2 2.1 2.12.108.93.2 0 2.6 2.6 2.6 0 3.9 4.8 1.1 1.0 6.1

1.6 6.98.91.803.43.42.73.22.62.52.44.04.72.02.32.31.51.52.62.13.93.94.44.02.02.03.0

4.0

3.4

O S D Y

10

14

09.1

2.4

09.1

2.4

09.1

2.4

FROM/TO 21PIN/SOUND

8

15

1.5

0.8

7.0

4.0

4.68.9

9.1

9 11

1.6

0

2.3

2.0

0

2.6 13

12

NCNC

9.1

8/18/2019 Matsui 1409r Tv Sm

20/29

A B C D E F

A B C D E F

2

1

3

4

5

6

7

8

DESCRIBED IN PARTS LIST ONLYCRITICAL FOR SAFETY,USE ONES

ARESINCE THESE PARTS MARKED BYCAUTION:

DANS LA NOMENCLATURE DES PIECESN’UTILISER QUE CELLS DECRITESDANGEREUSES AN POINT DE VUE SECURITE

ETANTLES PIECES REPAREES PAR UNATTENTION:

R 5 4 2

1

1 W

R 5 0 4

3 3

3 W

R505

220 1WS

DG

Q5012SK2480

SW

IC506 TLP621(D4-GR-LF2)

FEED BACK

1

2 3

4

V R 5 0 1

3 3 0

F501

T4A_L_250V

FH501

EYF-52BC

FH502

EYF-52BC

2

1

L5038R140027

CP501 THL-P03P-B1

1

2

R501

5.6 7W

HS501

763WAAA022

CP502

TV-50P-02-A1

1

2

P

H

TH501

PTH451C262BF140M

1

2

3

CAUTION: DIGITAL TRANSISTOR

L5010R8A393F28Y

12

34

T5028129054

1

10

11

12

13

14

15

16

2

3

4

5

6

7

9

SW501SDDFC30400

1

2

3

4

5 6

2

1

CD5011206635818

AC230V-240_50Hz

W802 W801

D 5 1 2

1 S S 1 3 3

D 5 0 8

1 S S 1 3 3

D 5 0 4

R M 1 1 C - E

I C

D 5 0 3

R M 1 1 C - E

I C

D 5 0 1

R M 1 1 C - E

I C

D 5 0 2

R M 1 1 C - E

I C

D518

1SS133

D516

21DQ09N

D513

11EQS04N

D505

11EQS04N

D510

RU2AM

D511

RMPG06J

D519

1SS133

D514

1SS133

D521

1SS133

R 5 1 8

2 . 2

K

+ - 1

%

B 5 0 1

B L 0 1 R N 1 - A

6 3

B504

BL01RN1-A63

Q5022SC2120Y

PROTECT

Q503

2SD863

5V SW

Q507

2SC1740SP

FEED BACK SWITCHING

D 5 0 6

M T Z J 1 5 B

D 5 0 9

M T Z J 1 8 B

D 5 0 7

M T Z J 1 5 B

D 5 2 8

M T Z J 5

. 6 B

R 5 0 8

2 . 7

K

1 / 4 W

R 5 1 2

2 . 2

K

R 5 1 3

5 6 0

R 5 0 6

6 8 0

1 / 4 W

R 5 1 1

2 . 2

M 1 / 4 W

R 5 1 0

2 . 2

M 1 / 4 W

R520

150K 1/2W

R 5 1 4

5 6 K 1 / 2 W

R 5 0 2

1 . 5

M 1 / 2 W

R 5 1 5

2 . 2

K

1 / 4 W

R 5 0 9

2 . 2

K

1 / 4 W

R523220 1/4W

R 5 2 4

R 5 2 5

R507

10K

R 5 2 1

R 5 1 6 3 3 0

1 / 4 W

R519

330

C511_1

150V KA

C 5 2 6

1 0 0

4 0 0 V

U S P

C 5 0 1

0 . 0

0 3 3

M

C503

0.0012KV B

C502

0.0012KV B

C 5 0 7

0 . 0

0 2 2

2 5 0 V

K X

C 5 1 4

6 8 0 P

2 K V

B P

C509

0.047 M

C531

0.01 M

C 5 1 8 0

. 2 2

E C Q U L

C 5 0 5

0 . 1

2 5 0 V

E C Q U L

C 5 2 9

0 . 0

0 2 2

2 5 0

V

K X

C520470P500V B

C512_1

470P500V B

C516

470P500V B

C517

0.0012500V B

C 5 0 4

1 T F

C 5 1 3

_ 1

0 . 0

0 1 B

C 5 2 2

4 7 0

1 6 V

Y K

C 5 1 5

4 7 0

1 6 V

Y K

C 5 2 7

4 7

1 6 V

Y K

C 5 1 9

1 0 0 0

2 5 V

Y K

C 5 2 1

2 2 0

1 6 0 V

P R

C 5 2 3

C 5 1 0

4 7

1 6 V

Y K

OF PRINTNOTE:THIS SC

OF PRINTING AND SUBJ ECT TO CHANGE WITHOUT NOTICENOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

BLUE

BROWN

BLUE

BROWN

G-5

(MAIN PCB)POWER SCHEMATIC DIAGRAM

NC

NC

NC

5.0

0

0.3

0.3

320

4.3

16

17

NC NC

8.8

8.18.2

11.6

10.9

7.7

5.6

6.2

+ B A D J .

8/18/2019 Matsui 1409r Tv Sm

21/29

A B C D E F

A B C D E F

2

1

3

4

5

6

7

8

S101

VIDEO

8

E8E25

E12

GND

TERHEAAFC

B+

GND

ABL

GND

COLHV

F

S

FB401

3214029F

1

10

11

2

3

4

5

6

7

8

9

Q401_12SD2599

H.OUTPUT

CD801127C140022

CP8061

CP801 TBS-X01X-A1

1

B

G

R

11

6

8

10

9

175

V801A34AGT13*07

T401

305Y001

1

2

3 4

6

I C401 AN5539NV-OUT

1 2 3 4 5 6 7

R429

3.3 1W

CP401

B05B-DVS

1

2

3

4

5

CP802A51048-1000

1

10

2

3

4

5

6

7

8

9

CP802B51048-1000

1

10

2

3

4

5

6

7

8

9

DESCRIBED IN PARTS LIST ONLYCRITICAL FOR SAFETY,USE ONESSINCE THESE PARTS MARKED BYCAUTION:

DANS LA NOMENCLATURE DESN’UTILISER QUE CELLS DECRITDANGEREUSES AN POINT DE VLES PIECES REPAREES PAR UNATTENTION:

HS401763WSA0004

W897W812

W813

W 8 0 4

W828

D403

11E1N

D 4 1 0

A U 0 2 A - E

I C

D 4 0 5

A U 0 2 A - E

I C

D407

1SS133

D406

1SS133

R 4 1 7

1 0 K

+ - 1

%

L 8 0 1

1 0 0 u

H 0 6 0 7

Q4022SC2271

H.DRIVE

D 4 0 4

M T Z J 6

. 2 B

R445 150K 1/4W

R 4 2 1

6 8 K

1 / 4 W

R 4 0 7

1 . 8

1 / 2 W

R408

1K1/4W

R 4 2 4

3 9 K

R409

150K

R411

56K

R420

27K

R415

3.3K 1/4W

R418

6.8K 1/4W

R 4 1 0

3 3 0

1 / 2 W

R 4 0 5

1 0 K

R414

2.2K 1/4W

R422

820 1/4W

R403

22K 1/4W

R 4 2 7

1 0 0 1 / 4 W

R 4 4 6

4 . 7

K

1 / 2 W

R 4 0 1

1 0 0

R404

15K1/4W

R406

1.8K1/4W

C 4 1 4

1 0 0

3 5 V

M H E

C 4 4 8 2

2

2 0 0 V M

H E

C 4 0 3

4 7 0

3 5 V

Y K

C 4 0 9 1

0 0

1 6 0 V

M H E

C 4 4 6

1

1 6 0 V

M H E

C 4 3 5

0 . 1 1

0 0 V T

F

C405

1 TF

C 4 3 0

0 . 1 1

0 0 V T

F

C 4 2 9

_ 1

0 . 0

0 2 2

B

C411_1

0.001 B

C 4 2 0

0 . 0

0 1

5 0 0 V

B

C 4 0 7

5 6 P

S L

C406

22P500V SL

C 4 3 7

0 . 3

3

2 5 0 V

P M S

C 4 4 3

0 . 0

0 4 7

1 . 6

K V

E C W H

C 4 4 0

4 7 0 P

5 0 0 V

B

C439

22P500V

SL

C 4 0 1

_ 1

1 0 0 P C H

C 4 0 4

0 . 0

4 7 B

C 8 1 9

0 . 0

0 1

2 K V

B

C 4 1 8

2 2 0 0

2 5 V

M H E

C 4 2 5

4 . 7

5 0 V

K A

C 4 1 0

4 7 0

3 5 V

Y K

TP401

G.OUT

R.OUT

B.OUT

AKB_WHITE

V_FEEDBACK

V_OUT

ABCL

H_OUT

AFC

VD

AKB_WHITE

AFC

P.CON+9V

P.CON+5V

H.DRV+B

+B_130V

GND

SCREEN

G-7

(C

THERMALPROTECTION

(MAIN PCB) DEFLECTION/CRT SCHEMATIC DIAGRAM

NC

0.3

0

137.0

130.0

0

0

0NC

PCB010

FOCUS

SCREEN

NC

TMX466

NC

23

22

GND+

AMP-

PUMPUP

VCC

2.123.92.42.424.212.40

1

NC

GND

G.OUT

R.OUT

B.OUT

180V

HEATER

GND

NC

VCC 9V

AKB

180V

R.OUT

B.OUT

HEATER

GND

NC

GND

G.OUT

VCC 9V

FROM/TO CRT

21

0

0

130

20

0.3

27.0

0

19

18

FROM/TO POWER

FROM/TO MI CON/TUNER

FROM/TO IF/CHROMA

NC

FOCUS

NC

FROM/TO DEFLECTION

TCX324

PCB110

8/18/2019 Matsui 1409r Tv Sm

22/29

A B C D E F

A B C D E F

2

1

3

4

5

6

7

8

IS NON POLAR ONE. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP THE RESISTOR MARKED F IS FUSE RESISTOR.NOTE:

J7050350_9982_05

1

1 0

1 1

1 2

1 3

1 4

1 5

1 6

1 7

1 8

1 9

2

2 0

2 1

3

4

5

6

7

8

9

I C351 AN7523

SOUND AMP

1 2 3 4 5 6 7 8 9

T

W827

W821

W814

W815

W826

B351BL01RN1-A63

L703

100uH

C353

2.250V KANP

Q3512SC2412K

BUFFER

Q701

2SC1815Y

VIDEO_BUFFER

Q7032SC2412K

VIDEO_AMP

D 7 0 6

M T Z J 6

. 8 B

R 3 5 4

4 7 K

R757

100

R 7 0 1 7

5

R 7 5 6

7 5 1 / 4 W

R 7 1 8

1 K

R 7 2 0

1 K

R719

1.2K

R717

100

R352

4.7K

R357

56 1/2W

R358

12K

R 3 5 6

6 8 0 K R

3 5 5 3

. 9 K

1 / 4 W

R 3 5 0

5 . 6

K

R 3 5 9

1 2 K

R 7 0 6 7

5

R712

1K

R708 75

R711

1K

R 7 0 4 6

8

R 7 0 5 7

5

R 7 1 0

5 . 6

K 1 / 4 W

R 7 1 5 7

5

C 3 5 9

1 0 0

1 6 V

Y K

C759

1050V YK

C 3 5 7

1 0

5 0 V

Y K

C 3 5 2

1 0

5 0 V

K A

C356

1050V KA

C 3 5 1

4 7 0

1 6 V

Y K

C 7 0 5

4 7 0 P B

C 7 0 4

4 7 0 P

B

C 7 0 6

2 2 P C H

C70

0.2

C 7 0 3

4 7 0 P B

C 3 6 0

0 . 0

0 4 7

B

C 3 5 0

0 . 0

0 3 9 X

C354

470P B

C 7 0 8 1

0 0

1 6 V

Y K

C702

4706.3V YK




NOTE:

L753

10uH

L702

10uH

L701

10uH

Q7042SA1037AK

VIDEO_AMP

AUDIO_OUT

TU_VIDEO_OUT

TU_AUDIO_OUTAV_VIDEO

AV_AUDIO

G-9

(MAIN PCB)

21PIN/SOUND SCHEMATIC DIAGRAM

NC

+

7.5 4.0 0 4.0 6.0 1.4 0 NC 0

NC

2.0

5.0

2.7

0

0

5.4

2.21.6

4.3 4.3

5.0FROM/TO IF/CHROMA

27

8/18/2019 Matsui 1409r Tv Sm

23/29

A B C D E F

A B C D E F

2

1

3

4

5

6

7

8

CAUTION: DIGITAL TRANSIST

Q602

DTA114EKA

RGB SW

CAUTION: DIGITAL TRANSISTOR

Q611DTC144EKA

RGB OFF SW

W808

W824

W809

Q6032SC2412K

SWITCHINGR635

4.7K

R627

2.2K

R609

1K1/4W

C604

3.350V YK C603

3.350V YK C602

3.350V YK




NOTE:

A-B

A-G

A-R

A-Y

G-11

(MAIN PCB)

VIDEO/RGB SW SCHEMATIC DIAGRAM

0

0.6

0

0 4.9

0.6

4.1

0.1

0

FROM/TO IF/CHROMA

8/18/2019 Matsui 1409r Tv Sm

24/29

A B C D E F

A B C D E F

2

1

3

4

5

6

7

8

Q8512SC1815Y

BUFFER

Q8522SC2412K

SYNC BUFFER

R875

56K

R865

100

R864

100

R 8 5 2

1 K

R 8 5 3 1

K

R 8 5 5 1

K

R 8 5 7 1

K

R854

330

R 8 6 7

1 5 K

R 8 5 1

2 . 2

K

R 8 8 1

1 5 0

R 8 8 0

2 2 K

R 8 7 1

2 2 K

R890

10K

C 8 6 0

1 0 0 P C H

C 8 5 8

1 0 0 P C H

C 8 5 2

0 . 1

M

C 8 6 7

0 . 0

1

B

C861

0.01 B

C855

0.022 F

C 8 6 8

1 0 0

6 . 3

V

Y K

L 8 5 1

1 0 u

H

W864

W 8 5 8

W860

W853

W854

W857

W861

W859

W 8 6 3

C 8 6 9

2 2

1 6 V

N P

THE DC VOLTAGE AT EACH PART WAS MEASURED



NOTE:

B850

BL02RN1-R62

OF PRINTING AND SUBJ ECT TO CHANGE WITHOUT NOTICENOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

IC850 ET106

DECORDER IC

1

1 0

1 1

1 2

1 3

1 4

1 5

1 6

1 7

1 8

1 9

2

2 0

2 1

2 2

2 3

2 4

2 5

2 6

2 7

2 8

3

4

5

6

7

8

9

CP852BIMSA-9130S-05L

1

2

3

4

5

CP851BIMSA-9130S-06L

1

2

3

4

5

6

C870

10016V YK

AVCC

TEST2

NC

CSB

TCLK.

TDATA

TEST4

TEST1

DGND

CLK.IN

RSTB

VIDEO

SYNC

TEST5

G-13

(T’TEXT PCB) T’TEXT SCHEMATIC DIAGRAM

(CP852)

FROM/TO VIDEO/RGB SW

(CP851A)

NC

NC

FROM/TO VIDEO/RGB SW

1.0

4.0

3.5

3.5

4.9

4.9

4.9

4.5

4.94.9

4.2

4.9

2.2

2.2

1.1

1.1

DVCC

WIND

TEST3

SCL

SDA

BLANK

BLUE

GREEN

RED

AGND

RGB SET

REF.

FLAG1

FLAG2

0

0

0

0

0

0

0

0

0

0

0

0

0

4.9

0.3

SDA

SCL

5V

SYNC

GND

2.1

1.46

4.6

TEXT B

TEXT G

TEXT R

TEXT Y

AV VIDEO 1

T TEXT RESET

8/18/2019 Matsui 1409r Tv Sm

25/29

4 1.0V 20µs/div 10 10mV 10µs/div

5 1.0V 5ms/div

The following waveforms were measured at the point of the correspondingballoon number in the schematic diagram.

NOTE:

WAVEFORMS

1 1.0V 200µs/div

8 500mV 500µs/div

3 1.0V 50ns/div 9 500mV 10µ

s/div

MICON/TUNER

H-1

2 1.0V 200µs/div

11 500mV 10µs/div

7 1.0V

Documents

Matsui 1409r Tv Sm