Merch Source Projector Entertainment IIMotherboard

Is your projector not responding? It could be your motherboard!

作成者: Michael Tan

Merch Source Projector Entertainment II Motherboard 下書き： 2015-06-16ガイド ID: 36762 -

㠓㠮文書㠯2019-10-20 01:01:34 PM (MST)ã «ä½œæˆ ã •ã‚Œã ¾ã —ã Ÿã€‚

© iFixit — CC BY-NC-SA jp.iFixit.com å…¨7 ページ分㠮1ページ目

はじめにはじめに

Follow this guide to repair components on the logic board. All you will need a solder gun and steadyhands.

ツールツール:Phillips #0 Screwdriver (1)Portable Soldering Iron (1)Spudger (1)

Merch Source Projector Entertainment II Motherboard 下書き： 2015-06-16ガイド ID: 36762 -

㠓㠮文書㠯2019-10-20 01:01:34 PM (MST)ã «ä½œæˆ ã •ã‚Œã ¾ã —ã Ÿã€‚

© iFixit — CC BY-NC-SA jp.iFixit.com å…¨7 ページ分㠮2ページ目

手順手順 1 — Outer Casing

Flip the projector onto its back and unscrew the nine 15mm screws using the Phillips #0 screwdriver.

手順手順 2

Flip the projector right side up andunscrew the two 12mm screws onthe light bulb panel located at therear of the projector with a Phillips#0 screw head.

The bottom right panel screw doesnot come completely out the paneldoor.

Merch Source Projector Entertainment II Motherboard 下書き： 2015-06-16ガイド ID: 36762 -

㠓㠮文書㠯2019-10-20 01:01:34 PM (MST)ã «ä½œæˆ ã •ã‚Œã ¾ã —ã Ÿã€‚

© iFixit — CC BY-NC-SA jp.iFixit.com å…¨7 ページ分㠮3ページ目

手順手順 3

Using your hands, gently pry the top and bottom of the projector casing apart.

Merch Source Projector Entertainment II Motherboard 下書き： 2015-06-16ガイド ID: 36762 -

㠓㠮文書㠯2019-10-20 01:01:34 PM (MST)ã «ä½œæˆ ã •ã‚Œã ¾ã —ã Ÿã€‚

© iFixit — CC BY-NC-SA jp.iFixit.com å…¨7 ページ分㠮4ページ目

手順手順 4 — Motherboard

Use the plastic opening tool to gently disengage the ribbon cable from its back housing.

Once the ribbon cable is disengaged gently pull the cable off the motherboard.

Once the housing is disengaged, the ribbon cable should slide out easy. Do not pull too hard onthe ribbon cable as it is very fragile.

Merch Source Projector Entertainment II Motherboard 下書き： 2015-06-16ガイド ID: 36762 -

㠓㠮文書㠯2019-10-20 01:01:34 PM (MST)ã «ä½œæˆ ã •ã‚Œã ¾ã —ã Ÿã€‚

© iFixit — CC BY-NC-SA jp.iFixit.com å…¨7 ページ分㠮5ページ目

手順手順 5

Unscrew the three 6 mm screws from the motherboard with the Phillips #0 screwdriver.

Be sure not to damage any of the wires atached to the motherboard.

Merch Source Projector Entertainment II Motherboard 下書き： 2015-06-16ガイド ID: 36762 -

㠓㠮文書㠯2019-10-20 01:01:34 PM (MST)ã «ä½œæˆ ã •ã‚Œã ¾ã —ã Ÿã€‚

© iFixit — CC BY-NC-SA jp.iFixit.com å…¨7 ページ分㠮6ページ目

To reassemble your device, follow these instructions in reverse order.

手順手順 6

Solder off all of the connections on the motherboard with a soldering iron.

Once connections are soldered off, the motherboard should be detached and ready forreplacement.

Need some help? Follow this guide to learn soldering basics.

While soldering the metal connections can get very hot. Never touch the iron with your hand. alsomake sure that the projector is fully turned off and not plugged in.

If there is hot glue on top on the connection with the motherboard, you will need to peel it off usingyour fingers.

Merch Source Projector Entertainment II Motherboard 下書き： 2015-06-16ガイド ID: 36762 -

㠓㠮文書㠯2019-10-20 01:01:34 PM (MST)ã «ä½œæˆ ã •ã‚Œã ¾ã —ã Ÿã€‚

© iFixit — CC BY-NC-SA jp.iFixit.com å…¨7 ページ分㠮7ページ目