MIS 65 & MIS 100

  • Upload
    balan

  • View
    19

  • Download
    0

Embed Size (px)

DESCRIPTION

Canusa

Citation preview

  • Product Data SheetProduct Data Sheet

    CANUSA

    -CPS

    Wraparound Sleeve for Offshore Heated Infill Systems

    CANUSA-CPS is registered to ISO 9001:2008.

    2-Layer

    Wrapid Sleeve

    Standard Shrink

    Girth-Weld Joints

    Oil & Gas

    Infill Systems

    Reel, J & S Lay

    MIS-65 / MIS-100

    Unique Adhesive Technology

    MIS-65 and MIS-100

    MIS-65

    and MIS-100

    MIS-65 and MIS-100

    Maximize Cost Savings

    Canusa's unique (open time) adhesive

    technology allows for lower installation

    preheat temperatures, superior adhesion to

    a wide range of mainline pipe coatings and

    consistent performance in rugged offshore

    environments. The adhesive has been

    formulated to provide long-term adhesion

    and excellent cathodic disbondment

    resistance properties.

    Hot Mast ic & Foam Inf i l lCompatibility

    sleeves can be used

    with hot mastic pour, polyurethane foam or

    other infill systems to provide effective

    long-term corrosion protection.

    sleeves are resistant to hot

    mastic pour systems and meet the

    requirements of the Drum Skin Test for

    high temperature effects.

    Precious time is saved in several areas when

    using sleeves on

    laybarge operations in combination with

    infill systems; lower preheat temperature

    equates to lower installation times, single

    wrap configuration eliminates the

    requirements for muitiple wrapping, and

    the pre-attached closure seal means less

    time is used handling, positioning and

    installing the joint protection materials.

    The overall system minimizes installation

    time and labour costs while promoting high

    production rates.

    Applications

    Temperature Range

    Pipe Sizes

    55 - 1220 (2 - 48)

    up to 100C (212F)

    Configurations

    For more than 35 years, Canusa-CPS has

    been a leading developer and manufacturer

    of specialty pipeline coatings for the sealing

    and corrosion protection of pipeline joints

    and other substrates. Canusa-CPS high

    performance products are manufactured to

    the highest quality standards and are

    available in a number of configurations to

    accommodate many specific project

    applications.

    sleeves have a

    patented one-piece construction that

    incorporates a pre-attached closure seal.

    This contributes to a rapid and consistent

    field installation procedure. Without any

    requirements for the wrapping of multiple

    layers, the field installation is fast, efficient

    and in-line with timing requirements of

    offshore laybarge operations. The

    crosslinked high-density polyethylene

    (HDPE) backing is designed to provide a

    rapid and consistent shrink response when

    installed with propane torch equipment.

    sleeves can be

    conveniently wrapped and installed in low

    ambient temperatures due to its excellent

    low temperature flexibility attributes.

    Corrosion Protection of Girth-Welds under heated infill systemson offshore service environments

    Flexible & Time EfficientInstallation

    Product Description

    Features & Benefits

    MIS-65 and MIS-100 heat-shrinkable

    sleeves provide superior corrosion

    protection and effective long-term

    adhesion to pipelines operating offshore at

    temperatures up to 100C (212F). MIS-65

    and MIS-100 sleeves are specifically

    engineered for use in combination with hot

    marine mastic pour, polyurethane foam or

    other infill systems. MIS-65 and MIS-100

    sleeves are resistant to the severe

    conditions of hot mastic pour operations

    and maintain their full set of anti-corrosion

    properties. MIS-65 and MIS-100 are fully

    compatible with a wide range of pipeline

    coatings, including PP, FBE, PE, Coal Tar and

    Tape.

    MIS-65 and MIS-100

    MIS-65 and MIS-100

    Offshore Pipelines

  • Wraparound Sleeve for Offshore Heated Infill SystemsMIS-65 / MIS-100

    Canusa warrants that the product conforms to its chemical and physical description and is appropriate for the use stated on the installation guide when used in compliance with Canusas written instructions. Since many installation factors arebeyond our control, the user shall determine the suitability of the products for the intended use and assume all risks and liabilities in connection therewith. Canusas liability is stated in the standard terms and conditions of sale. Canusa makes noother warranty either expressed or implied. All information contained in this installation guide is to be used as a guide and is subject to change without notice. This installation guide supersedes all previous installation guides on this product.E&OE

    Printed on recycled paper. Recyclable.

    www.canusacps.com

    PDS-A4-MIS-65&100-rev014

    The product selection chart shown here is intended as a guide for standard products.Consult your Canusa representative for specific projects or unique applications.

    Back

    ing

    Sle

    eve

    Resi

    stance

    toIn

    fill

    Typical Product Properties

    102 (216)40 (58)

    24 (3480)700500pass52301020

    > 8 Jno holiday @ 10kV

    80 (46)65 (37)

    < 7pass0.05

    -14 (7)no melt or sag

    1.8 (73)

    pass, no holidays @ 10kV< 10%< 15%< 15%

    18

    < 7

    124 (255)52 (75)

    24 (3480)700500pass52301020

    > 8 Jno holiday @ 10kV

    115 (66)90 (51)

    pass0.05

    -15 (5)no melt or sag

    1.8 (73)

    pass, no holidays @ 10kV< 10%< 15%< 15%

    18

    < 7< 7

    UnitTest Standard MIS-100MIS-65

    C (F)N/cm (psi)

    MPa (psi)%%

    VisualShore D

    mgohm-cmkV/mm

    ----

    N/cm (pli)N/cm (pli)mm radmm radVisual

    %C (F)Visual

    mm (mils)

    Visual%%%

    2

    ASTM E28DIN 30 672

    ASTM D638ASTM D638ASTM D638ASTM D2671ASTM D2240ASTM D1044ASTM D257ASTM D149

    DIN 30 672DIN 30 672ASTM D1000DIN 30672ASTM G8ASTM G42, 48hrsASTM D870ASTM D570ASTM D2671-CD024 A P50-F SD004

    pipe 24, mold 26, mastic @ 200CASTM D1000ASTM D638ASTM D638

    Softening pointLap shear @ 23C

    Tensile strengthElongationHeat Aging - Elongation @ BreakHeat Shock - 4hrs @ 250CHardnessAbrasion resistanceVolume ResistivityDielectric Strength

    ImpactIndentation ResistancePeel Strength to Steel, PE, PPPeel Strength @ 23CCathodic Disbondment @ 23CCathodic Disbondment @ 65CHot Water ImmersionWater AbsorptionLow Temp. FlexibilityDrum Skin Test

    Visual InspectionChange in Peel StrengthChange in Tensile StrengthChange in Elongation

    Fully Recovered Thickness

    How To Order:

    300, 450, 600, 700mm (12, 18, 24, 28")

    Pipe Size

    Colour BK- Black

    55 - 1220mm (2 -48")

    Heated Infill Systems

    MIS-65 - MIS-100 -65C (149F) 100C (212F)

    0.88mm (35 mils)

    Sleeve Width

    Backing (thickness as supplied)

    Backing (thickness fully recovered)

    Adhesive (thickness as supplied)

    Maximum Operating Temperature

    MIS-65 315-450 BK

    Dim

    ensi

    ons

    &O

    rderi

    ng

    Info

    Standard MIS-65 and MIS-100 Optionssleeve

    width

    The above represent standard ordering options. Consult your Canusa representative for any unique project requirements or CanusaWrap configuration.

    Min. Sleeve Width =50 mmBare Steel Dimension + (2")

    on each side of the pipe joint.

    0.63mm (25mils)

    0.80mm (32mils)

    Celsius

    105

    90

    75

    60

    45

    30

    Fahrenheit

    221

    194

    167

    140

    113

    86

    Sle

    eve

    Opera

    ting

    Chara

    cteri

    stic

    sProduct Selection Guide

    MIS-100MIS-65

    90C (194F)

    100C (212F)

    excellent

    excellent

    excellent

    Tape, FBE, PE, PP

    St 3 (min) SA 2(rec)

    65C (150F)

    65C (149F)

    excellent

    excellent

    excellent

    Bit, Tape, CTE, FBE, PE

    St 3 (min) SA 2(rec)

    Minimum Installation Temperature

    Maximum Operating Temperature

    Resistance to Hot Infill Pour

    Compatibility to Hot Marine Mastic

    Compatibility to Polyurethane Foam

    Main Line Coating Compatibility

    Recommended Surface Preparation

    PipelineOperatingTemperature

    Pre-heatTemperature

    Choose your sleeve based on

    Operating Temperature and

    Characteristics listed below.

    pipesize

    Adhesi

    ve

    Application

    CANUSA-CPSSHAWCOR LTDa division of .

    25 Bethridge RoadToronto, OntarioM9W 1M7,CanadaTel: +1 (416) 743-7111Fax: +1 (416) 743-5927

    Canada U.S.A./Latin AmericaCANUSA-CPS

    SHAWCOR INC.a division of2408 Timberloch PlaceBuilding C-8The Woodlands, Texas77380, U.S.A.Tel: +1 (281) 367-8866Fax: +1 (281) 367-4304

    Europe/Middle East Asia/PacificCANUSA-CPSa division of Canusa Systems Ltd.Unit 3, Sterling ParkGatwick RoadCrawley, West SussexEngland RH10 9QTTel: +44 (1293) 541254Fax: +44 (1293) 541777

    CANUSA-CPSa division of .#05-31, Blk 52, FrontierUbi Avenue 3Singapore408867Tel: +65-6749-8918Fax: +65-6749-8919

    SHAWCOR LTD