Embed Size (px)
Citation preview
Modeling and Analysis of PSRR in Analog PWM Class D Amplifiers
Tong Ge; Chang, J.S.; Wei Shu;Circuits and Systems, 2006. ISCAS 2006. Proceedings. 2006 IEEE International Symposium on 0-0 0 Page(s):4 pp.Digital Object Identifier 10.1109/ISCAS.2006.1692853
指導教授：易昶霈學 生：杜彥諴學 號： 98662006
NCUE-Graduate Insititute of Integrated Circuit Design
2
OUTLINE INTRODUCTION MODELING OF PWM CDAS INVESTIGATION INTO THE PARMETERS
AFFECTING PSRR RESULTS CONCLUSIONS
NCUE-Graduate Insititute of Integrated Circuit Design
3
INTRODUCTION Power Efficiency CDA modulation method PSRR
NCUE-Graduate Insititute of Integrated Circuit Design
4
INTRODUCTION Power Efficiency
note : CDA’s MOS operate in triode and cut-off regions that have low quiescent power.
Type Performance
Class A <25%
Class B <78.5%
Class AB 25%~78.5%
Class D >80%
NCUE-Graduate Insititute of Integrated Circuit Design
5
INTRODUCTION CDA modulation method
1. Pulse Width Modulation
2. Sigma-Delta Modulation
3. Bang-Bang Control Moudlation
NCUE-Graduate Insititute of Integrated Circuit Design
6
INTRODUCTION CDA modulation method
1. Pulse Width Modulation
NCUE-Graduate Insititute of Integrated Circuit Design
7
INTRODUCTION CDA modulation method
2. Sigma-Delta Modulation(Pulse-Density-Modulated-like)
NCUE-Graduate Insititute of Integrated Circuit Design
8
INTRODUCTION CDA modulation method
3. Bang-Bang Control Modulation(Pulse-Density-Modulated-like)
NCUE-Graduate Insititute of Integrated Circuit Design
9
INTRODUCTION CDA modulation method
4. Digital CDA modulation method
NCUE-Graduate Insititute of Integrated Circuit Design
10
INTRODUCTION PSRR(Power Supply Rejection Ratio)
嚴格來說就是電源 IC 對輸入電壓所挾帶來的雜訊 (Vin Ripple) 清除的能力
電源斥拒比 (PSRR) 影響輸出訊號的因素除了電路本身之外還有電源級 . PSRR 是一個用來描述輸出訊號受電源影響的量 . PSRR 越大輸出訊號越不受電源影響 .
Critical parameter
1. Gain of integrator
2. Gain of PWM
3. Gain of feedback factor
NCUE-Graduate Insititute of Integrated Circuit Design
11
MODELING OF PWM CDAs Modeling an open-loop PWM CDA Modeling a close-loop PWM CDA
NCUE-Graduate Insititute of Integrated Circuit Design
12
MODELING OF PWM CDAs Modeling an open-loop PWM CDA
NCUE-Graduate Insititute of Integrated Circuit Design
13
MODELING OF PWM CDAs Modeling an open-loop PWM CDAGpwm = gain of PWM stage
N = noise in supply rail
NCUE-Graduate Insititute of Integrated Circuit Design
14
MODELING OF PWM CDAs Modeling a close-loop PWM CDA
積分器
Feedback network(R1 and Rfb)
NCUE-Graduate Insititute of Integrated Circuit Design
15
MODELING OF PWM CDAs Modeling a close-loop PWM CDA
NCUE-Graduate Insititute of Integrated Circuit Design
16
MODELING OF PWM CDAs Modeling a close-loop PWM CDAG1=amp input to inverting input of integrator
H1= feedback factor
Aop = op-amp open –loop gain
NCUE-Graduate Insititute of Integrated Circuit Design
17
MODELING OF PWM CDAs Modeling a close-loop PWM CDA
NCUE-Graduate Insititute of Integrated Circuit Design
18
INVESTIGATION INTO THE PARMETERS AFFECTING PSRR
The gain of integrator The gain of PWM stage The feedback factor
NCUE-Graduate Insititute of Integrated Circuit Design
19
INVESTIGATION INTO THE PARMETERS AFFECTING PSRR
The gain of integratorEq10 中 Gint可以大幅的增加 PSRR,所以 Aop越大越好 .會在 fig6再一次
看到
NCUE-Graduate Insititute of Integrated Circuit Design
20
INVESTIGATION INTO THE PARMETERS AFFECTING PSRR
The gain of PWM stage
NCUE-Graduate Insititute of Integrated Circuit Design
21
INVESTIGATION INTO THE PARMETERS AFFECTING PSRR
The feedback factor
Increasing H1 results in two major shortcomings
1. reduced dynamic range of the amplifier
2. reduced amplifier gain
NCUE-Graduate Insititute of Integrated Circuit Design
22
RESULTS
NCUE-Graduate Insititute of Integrated Circuit Design
23
CONCLUSIONS
這篇 PAPER 表現了 , 一個分析 CDA 中 PSRR 的方法探討了影響 PSRR 的三個因素
NCUE-Graduate Insititute of Integrated Circuit Design
24
Thanks for pay attention.
