Opterna datasheets 2

Americas:(703) [email protected]

Europe:+44(0)2031 301 [email protected]

Middle East:+971 4 299 [email protected]

Asia Pacific:+91(0) 484 2104 [email protected]

OpternaROpternaR

DSFC8rev1Visit: Opterna.com

Fiber Optic Outdoor Drop Cable

Opterna outdoor flat drop cable is constructed with one or two single mode fiber (ITU-T G.652D). The cable is protected by a dielectric strength member made of fiberglass reinforced plastic (FRP), steel wire and a LSZH outer jacket.

Designed for outdoor installation the cable is well suited for connections between the dome closure and small dwelling unit/ warehouse and independent villas.

Utilizing a 250μm fiber, the cable unit is suitable for use with industry standard connector.

Introduction

• Robust and lightweight

• Colour coded fibers for easy identification

• LSZH jacket for internal use

• Standard cable length of 1 Km

Features: Fiber Optic Outdoor Drop Cable

OSP Solutions

1/3





OpternaROpternaR



• FTTx applications

• CCTV

• ITU.T G.652D / G.657A

Applications:

Standards:

Cable Construction:

Color of Buffer:

Transmission Performance:

OSP Solutions

Parameter Value

Primary Coating Color Layer 250 ± 15 μm

Dielectric Strength Member FRPØ 0.45 ± 0.05mm

Dielectric Strength Member Steel WireØ 1.2 ± 0.05mm

Outer Jacket LSZH

1 core Drop Cable 01 Blue -

2 core Drop Cable 01 Blue 02 Orange

Fiber Types Maximum Attenuation: Value

G.652D/G.657A1 @1310nm@1550nm

0.4dB/km0.3dB/km

Maximum Dispersion ps/nm/km ≤3.5@1285~1339nm≤18@1550nm

Cutoff Wavelength nm <1260

Mode Field Diameter μm 9.2 ± [email protected] ± 0.8@1550nm

Core Clad Concentricity μm ≤0.5

Cladding Diameter μm 125 ± 1

2/3





OpternaROpternaR

DSFC5rev1Visit: Opterna.comVisit: Opterna.com

Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna name and logo are registered trademarks of Opterna Technology Limited.

OSP Solutions


Mechanical & Environmental:

Cable Properties:

Ordering Info:

XXX : OS1, OS2, 7A1, 7A2, 7B2, 7B3YYY : 001, 002

Temperature Range -40⁰C to +60⁰C

Fire Performance IEC 60332-1, IEC 60754-2 & IEC 61034

FC-XXX-DRP-SW-YYY-LZ Fiber Optic Singlemode Outdoor Drop Cable, LSZH

FC-XXX-DRP-SW-YYY-PV Fiber Optic Singlemode Outdoor Drop Cable, PVC

SheathColor

FiberCount

NominalDiameter

[mm]

NominalWeight

[Kg/Km]

Maximum Tensile Load Minimum Bend Radius Crush Resistance

Short Term

[N]

Long Term

[N]

Loaded[mm]

Installed[mm]

Short Term

[N]

Long Term

[N]652D 657A 652D 657A

Black 1 or 2 2.0×3.0 ± 0.2mm 15.6 600 300 60 50 30 20 1000 500

3/32/3





OpternaROpternaR

Visit: Opterna.comDSCArev1 1/4

Fiber Optic Patchcords and Pigtails

Opterna offers high performance patchcords and pigtails for use in all types of fiber optic networks. The Opterna® patchcords & pigtails are manufactured using state-of-the-art controlled manufacturing processes to operate over a wide range of wavelengths, ranging from 850nm - 1300nm for Multimode and 1310nm - 1550nm for Singlemode fiber. Opterna patchcords and pigtails are terminated with high quality connectors, which provide low insertion loss and high return loss. Each patchcord or pigtail is individually tested and supplied with test certificates. The unique serial number provides traceability of every single product.

Introduction

• Available in singlemode and multimode fiber types

• Available with all fiber optic connector types

• High quality ferrules and housings

• Low insertion loss and high return loss

• Individual test results and unique trace number provided with every product

• Mating Durability: 1000 cycles; <0.2 dB change

• Temperature range: -40 °C to +70°C

• RoHS compliant

• IEC, EIA/TIA and GR-326-CORE compliant

Features Patchcords and Pigtails

Fiber Interconnect & Passives





OpternaROpternaR


Patchcords and Pigtails

• Datacenter and Datacom

• FTTX deployments

• Pre-terminated assembly interconnection

• CATV, WAN, LAN and Telecom networks

• Testing and measurement equipment


Applications:

Size & Dimensions:

Chan. 2

Chan. 1

End 1

Chan. 1

Chan. 2

End 2

L

l 2

End 2

Fig.2: Simplex patchcord schematic

Fig.1: Duplex patchcord schematic

End 1

L

l 2

Fig.3: Pigtail schematic

Length of assembly (L) L -0/+100mm (for L<0.5.m)

L -0/+150mm (for 0.5m>L<5m)

L -0/+200mm (for L>5m)

Split length (l1) - only for duplex 150 ± 25mm

Traceability label distance (l2) 200 ± 25mm (from one end)





OpternaROpternaR


Visit: Opterna.com

Parameter SpecificationFiber Types Multimode: OM1, OM2, OM3, OM4

Singlemode: G652D, G657A1, G657A2, G657B2, G657B3, G655Cable type Simplex: 2.8, 2.0, 1.8, 0.9, 0.6, 0.250mm

Duplex: 2.8, 2.0, 1.8mmFlat duplex: 2.8mm

Cable Colours Blue, Yellow, White, Orange, Aqua, Heather VioletConnector Types SC, LC, MU, FC, ST, MTRJ, ESCON, E-2000, SMA, FDDI

Endface Finish PC, UPC, APC

Parameter Connector Type Max TypicalInsertion loss (dB) Multimode SC, LC, MU, FC, ST, E-2000, ESCON, FDDI 0.30 0.20

Multimode MTRJ & SMA 0.75 0.50Singlemode SC, LC, MU, FC, ST, ESCON, FDDI 0.30 0.20

E2000 0.25 0.12MTRJ 0.50 0.30

Return Loss (dB) All types Singlemode UPC endface finish type 50 55All types Singlemode APC endface finish type 60 65

General Specification:

Optical performance specification:

Patchcords and PigtailsFiber Interconnect

& Passives





OpternaROpternaR


Ordering Info:


CA

Connector TypeEnd 1

ConnectorFinish End 1

CableDiameter

Fiber Type Cable Type CableMaterial

Connector TypeEnd 2

ConnectorFinish End 2

CableLength

CableColour

ST ST connector

P PC 16 1.6mm OM1 62.5/125MM

SX Simplex L LSZH ST ST connector

P PC 005 0.5meter

BL Blue

SC SC connector

U UPC 18 1.8mm OM2 50/125MM

DX Duplex V PVC SC SC connector

U UPC 015 1.5meter

YL Yellow

SD SC duplex A APC 20 2.0mm OM3 50/125 MMLaserOptimized

FD FlatDuplex

R RISER SD SC duplex A APC 150 15meter

WH White

FC FC connector

28 2.8mm OM4 50/125 MMLaserOptimized

TB TightBuffered

P PLENUM FC FC connector

Blank forpigtail

OR Orange

LC LC connector

02 250um OS2 9/125 SMG.652D

ES Easy strip

LC LC connector

AQ Aqua

LD LC duplex 06 600um 7A1 G-657A1 SMBendinsensitive

LT Loose tube

LD LC duplex HV HeatherViolet

MU MUconnector

09 900um 7A2 G-657A2 SMBendinsensitive

MU MUconnector

MD MU duplex

7B2 G-657B2 SMBendinsensitive

MD MU duplex

E2 E-2000connector

7B3 G-657B3 SMBendinsensitive

E2 E-2000connector

MT MTRJconnector

655 9/125 SMG-655

MT MTRJconnector

FD FDDIconnector

FD FDDIconnector

ES ESCONconnector

ES ESCONconnector

SM SMAconnector

SM SMAconnector

Blank forpigtail


Patchcords and Pigtails

OpternaROpternaR





Visit: Opterna.com

Fused 1x2 (2 x2) Splitters

Opterna High Performance Bidirectional Single Mode Splitters are used to split light from one fiber into two output fiber lines with ultra low loss. It also can be used to combine light from two fibers into one. It is a compact, fused, all fiber technology device. Manufactured using state-of-the-art Fused Bi-conical Taper process (FBT), they exhibit uniform performance over entire optical spectrum from 1260 to 1600nm with near zero loss. The epoxyfree optical path provides good power handling capability.

Opterna fused splitter uses highly reliable and specialized packaging technology, providing excellet thermal stability and long life. The advanced packing ensures very good stability under vibration and impact, making these splitters ideal for outdoor applications. Opterna splitters are available in both 1x2 and 2x2 configuration with different package and connector types to cater most applications.

Introduction

• All fiber technology • Bidirectional • Triple Play • Ultra broadband 1260 ~ 1600nm • Extreme stability to thermal variations• Tap coupler versions of any split ratio • Near Zero Excess Loss • Low Back Reflection • Low Polarization Dependant Loss • Excellent Uniformity• Compact Packaging • Designed to comply GR-1209-CORE and GR-1221-CORE • 100% rigorous screening (rapid temperature cycling) and testing • Variety of package and pigtail options• Factory connectorization available• Custom Packaging available

Features: Fused 1x2 (2 x2) Splitters

OSP Solutions

DSCP1rev1 1/3

OpternaROpternaR





Visit: Opterna.com


• FTTX• Telecommunication Networks• CATV Networks• Fiber Optic Sensors• Optical Fiber Communication Systems

*other coupling ratios are also available†All insertion loss are excluding connector loss

Applications:

Specifications

OSP Solutions

Parameter Narrow Band single Window

Wide Band singleWindow

Narrow Band single Window

Wide Band singleWindow

OperatingWavelength

1310±20nm or1550±20nm or

1585±20nm

1310±40nm or 1550±40nm or 1530-1610nm (for DWDM)

1310±20nm and 1550±20nm

1310&1550(±40nm) or1260- 1360 & 1480-

1580nm

Grade Premium Standard Premium Standard Premium Standard Premium Standard

Excess Loss : Typical 0.1 dB 0.2 dB 0.1 dB 0.2 dB 0.1 dB 0.2 dB 0.1 dB 0.2 dB

Insertion Loss : Maximum (Loss of high power port/ Loss of low power port)*

50/50 3.4 dB 3.6 dB 3.4 dB 3.6 dB 3.6 dB 3.8 dB 3.6 dB* 3.8 dB*

55/45 3.0/3.9 dB 3.2/ 4.1 dB 3.0/ 3.9 dB 3.2/ 4.1 dB 3.1/ 4.0 dB 3.3/ 4.2 dB 3.2/ 4.1 dB 3.4/ 4.3 dB

60/40 2.5/ 4.4 dB 2.7/ 4.6 dB 2.5/ 4.4 dB 2.7/ 4.6 dB 2.6/ 4.6 dB 2.8/ 4.8 dB 2.7/ 4.7 dB 2.9/ 4.9 dB





85/15 1/ 8.8 dB 1.2/ 9.0 dB 1/ 8.8 dB 1.2/ 9.0 dB 1.0/ 9.0 dB 1.1/ 9.2 dB 1.0/ 9.2 dB 1.2/ 9.4 dB



98/2 0.3/ 18.0 dB 0.3/ 18.5 dB 0.35/18.5dB 0.4/ 19.0 dB 0.35/18.7dB 0.4/ 19.2 dB 0.3/ 18.5 dB 0.4/ 18.7 dB

99/1 0.2/ 21.5 dB 0.3/ 22.0 dB 0.3/ 22.1 dB 0.4/ 22.5 dB 0.3/ 22.4 dB 0.4/ 22.8 dB 0.3/ 22.0 dB 0.35/22.3dB

Uniformity, max(for 50/50) 0.6 dB 0.8 dB 0.6 dB 0.8 dB 0.7 dB 0.8 dB 0.8 dB* 1.0 dB*

PDL max 0.2 dB

Directivity >50 dB

Operating Temperature -40 to + 85°C

Fiber Type G 652D

Dimensions, LD 2.9 mm (dia) x 51 mm (L), bare fiber

,MD 3.05mm (dia) x 65mm (L), 900um hytrel tubing

,HD Plastic Housing, 96.5mm(I) x 12mm (b) x 10mm (t),mm jacketed cable

DSCP1rev1 2/3

OpternaROpternaR





Visit: Opterna.comVisit: Opterna.com

Spectral Response Chart

Ordering Info:

OSP Solutions


7

6

5

4

3

2

1

0

1230 1280 1330 1380 1430 1480 1530 1580 1630

Wavelength (nm)

Insertion Loss

B d

CP

Split Ratio Grade PortConfiguration

Package Type Wavelength in nm Connector Type Connector Finish

Lead Length

50 50:50 P Premium 12 1 x 2Splitter

L Light Duty, 250μmBuffered fiber

13NB 1310 ± 20nm NO NoConnector

N No connector

10 1m ± 0.1m

45 55:45 S Standard 22 2 x 2Splitter

M Medium Duty,900μm Tubing

15NB 1550 ± 20nm ST STconnector

U UPC 15 1.5m ± 0.1mand so on

40 60:40 C Custom Type*

J Heavy Duty, 2mmJacketed

35NB 1310 ± 20 &1550 ± 20nm

SC SCconnector

A APC 00 For Modularversions

H Heavy Duty, 3mmJacketed

58NB 1585 ± 20nm FC FCconnector

A AluminiumCassette

13WB 1310 ± 40nm LC LCconnector

P Moulded PlasticCassette

15WB 1550 ± 40nm MU MUconnector

C Custom Module* 35WB 1310 ± 40 &1550 ± 40nm

E2 E-2000connector

G LGX Module NWBB 1260 - 1360 &1480 - 1580nm

WDBB 1260 - 1360 &1450 - 1600nm

ULBB 1260 - 1610nm


DSCP1rev1 3/3





OpternaROpternaR

Visit: Opterna.comDSOMMrev1 1/3

Fused Multimode Splitters

Opterna High Performance Bidirectional Multimode Splitters are used to split light from one fiber into two output fiber lines with ultra low loss. It also can be used to combine light from two fibers into one. It is a compact, fused, all fiber technology device. They are manufactured using state-of-the-art Fused Bi-conical Taper process (FBT) on graded index fibers with core diameters of 50um or 62.5um. Opterna’s Multimode splitters are commonly used in short distance communications with LED sources operating at 1310nm or 850nm. They are wavelength independent over a broad range of wavelengths with uniform modal power distribution launch condition.

Opterna’s MM fused splitters use highly reliable and specialized packaging technology, providing excellent thermal stability and long life. Opterna splitters are available in both 1x2 and 2x2 configuration with different package and connector types to cater most applications.

Introduction

• All fiber technology

• Bidirectional

• Accurate split ratio

• Ultra-low excess loss

• Excellent directivity

• Available in 50/125, 62.5/125 & OM3

• Tap Ratios available

• Extreme stability to thermal variations

• Excellent Uniformity

• Compact Packaging

• Variety of package and pigtail options

• Factory connectorization available

• Custom Packaging available

Features Fused Multimode Splitters






OpternaROpternaR

Visit: Opterna.comDSOMMrev1 2/3


• Fiber Optic Sensors• LAN• Short distance transmission• Video Networks• Signal Monitoring• Network Monitoring


Applications:

Specifications:

Fiber Type 62.5/125μm OR 50/125μm

Operating Wavelength 850 and 1300nm

Split Ratio* 50:50

Maximum Insertion Loss 3.7dB (Without Connector)

Directivity > 40dB

Operating Temperature -400C to +850C

PackageLight Duty Stainless steel tube, 3.05mm (dia) x 55mm (L)

Medium Duty Stainless steel tube, 3.05mm (dia) x 65mm (L)

Heavy Duty Plastic Housing, 96.5mm (l) x 12mm (b) x 10mm (t)





OpternaROpternaR

Visit: Opterna.comDSADrev1 3/3

Visit: Opterna.com

Ordering Info:


OMMC

Split Ratio Fiber Type PortConfiguration

Package Type Wavelengthin nm

Connector Type Lead length

50 50:50 6 62.5/125 12 1 x 2Splitter

L Light Duty,250μm Buffered fiber


10 1m ± 0.1m

55 55:45 5 50/125 22 2 x 2Splitter

M MediumDuty, 900μmTubing

13NB 1300 ± 20nm ST STConnector

15 1.5m ± 0.1mand so on

60 60:40 &so on

3 OM3 J Heavy Duty,2mmJacketed

1385 1310 ± 20 &850 ± 20nm

SC SCConnector

00 For Modularversions

H Heavy Duty,3mmJacketed

AQ Aqua FC FCConnector

A AluminiumCassette

HV Heather violet LC LCConnector

P Moulded Plastic Cassette

BK Black

C Custom* ME Metal

G LGX Module



OpternaROpternaR





Visit: Opterna.com

Fused Wideband Tap Couplers

Opterna High Performance Tap Couplers are used to tap light from a fiber line, to monitor the signals. It is used in Erbium doped fiber amplifiers (EDFA) and telecommunication networks for monitoring the signal strength of different channels. Manufactured using state-of the- art Fused Bi-conical Taper process (FBT), they exhibit uniform performance over entire optical spectrum from 1260 to 1600nm with near zero loss. The epoxyfree optical path provides good power handling capability.

Opterna Tap couplers use highly reliable and specialized packaging technology, providing excellent thermal stability and long life. The advanced packing ensures very good stability under vibration and impact, making these splitters ideal for outdoor applications. Opterna tap couplers are available in both 1x2 and 2x2 configuration with different package and connector types to cater most applications.

Introduction

• Available with different tap ratios from 1 to 10%

• All fiber technology (fused)

• Broadband performance

• Extreme stability to thermal variations

• Tap coupler versions of any split ratio

• Near Zero Excess Loss

• Low Back Reflection

• Low Polarization Dependant Loss

• Compact Packaging

• Designed to comply GR-1209-CORE and GR-1221-CORE

• 100% rigorous screening (rapid temperature cycling) and testing

• Variety of package and pigtail options

• Factory connectorization available

Features: Fused Wideband Tap Couplers

OSP Solutions

DSCP2rev1 1/3

OpternaROpternaR





Visit: Opterna.com


• EDFA signal monitoring• Network channel strength monitoring• FTTx• Telecom & CATV Networks• Fiber Optic Test & Sensing Equipment

†All insertion loss are excluding connector loss

Applications:

Specifications

OSP Solutions

Parameter Single window /C -Band/L -Band

Dual Window C +L B and for DWDM

OperatingWavelength

1530-1570nm or 1570-1610nmor 1310±20nm

1310±20nm and 1550±20nm 1530-1610nm

Grade Premium Standard Premium Standard Premium Standard

Excess Loss : Typical 0.1 dB 0.2 dB 0.1 dB 0.2 dB 0.1 dB 0.2 dB

Insertion Loss : Maximum (Loss of high power port/ Loss of low power port)*

90/10 0.7/ 10.8 dB 0.8/ 11.0 dB 0.8/ 11.0 dB 0.9/ 11.5 dB 0.8/ 11.0 dB 0.9/ 11.5 dB

95/5 0.4/ 13.8 dB 0.5/ 14.0 dB 0.5/ 14.0 dB 0.6/ 14.5 dB 0.5/ 14.0 dB 0.6/ 14.2 dB

98/2 0.3/ 18.0 dB 0.3/18.5 dB 0.35/ 18.5 dB 0.4/ 19.0 dB 0.3/18.5 dB 0.4/18.7 dB

99/1 0.2/ 21.5 dB 0.3/ 22.0 dB 0.3/ 22.1 dB 0.4/ 22.5 dB 0.3/ 22.0 dB 0.35/ 22.3 dB

Max Loss Variation in the tap leg90/10 0.3 dB 0.5 dB 0.5 dB 0.7 dB 0.5 dB 0.7 dB

95/5 0.4 dB 0.6 dB 0.6 dB 0.8 dB 0.6 dB 0.8 dB

98/2 0.4 dB 0.6 dB 0.6 dB 0.8 dB 0.6 dB 0.8 dB

99/1 0.4 dB 0.6 dB 0.6 dB 0.8 dB 0.6 dB 0.8 dB

PDL max 0.2 dB

Directivity >³55 dB

Reflectance -60 dB for Premium grade (<-55dB for Standard Grade)

Operating Temperature -40 to +85 °C

Storage Temperature -40 to +70 °C

Fiber Type SMF-28 or SMF-28e

Dimensions, LD 2.9mm (dia) x 51mm (L)

,MD 3.05mm (dia) x 65mm (L)

,HD Plastic Housing, 96.5mm (l) x 12mm (b) x 10mm (t)

DSCP2rev1 2/3

OpternaROpternaR






Spectral Response Chart

Ordering Info:

OSP Solutions


CP

CouplingRatio

Grade PortConfiguration

Package Type Wavelength in nm Connector Type Connector Finish

Lead Length

10 90:10 P Premium 12 1 x 2Splitter

L Light Duty, 250μmBuffered fiber


N No connector

10 1m ± 0.1m

05 95:05 S Standard 22 2 x 2Splitter

M Medium Duty,900μm Tubing

15NB 1550 ± 20nm ST STconnector

U UPC 15 1.5m ± 0.1mand so on

01 99:01 C Custom Type*

J Heavy Duty, 2mmJacketed

35NB 1310 ± 20 &1550 ± 20nm

SC SCconnector

A APC 00 For Modularversions

H Heavy Duty, 3mmJacketed

13WB 1310 ± 40nm FC FCconnector

A AluminiumCassette

15WB 1550 ± 40nm LC LCconnector

P Moulded PlasticCassette

35WB 1310 ± 40 &1550 ± 40nm

MU MUconnector

C Custom Module* E2 E-2000connector

G LGX Module


0

5

10

15

20

25

1530 1540 1550 1560 1570

W avelength (nm)

-0.2

0

0.2

0.4

0.6

0.8

1

Tap Port High Power Port

High

Power

Port

IL

Tap

Port

IL

Insertion Loss: 99/1 Tap Coupler

DSCP2rev1 3/3





OpternaROpternaR

Visit: Opterna.comDSMCrev1 1/3

Mode Conditioning Patchcords

Opterna Mode Conditioning Patchcord (MCP) is designed for long wave (LX) multimode applications of Gigabit Ethernet. It is compliant with the IEEE 802.3z application standard. The purpose of Mode Conditioning Patchcord is to condition the launch to ensure specified link lengths and it should be inserted on both ends of a link to interface between a single mode adapter card and a multimode cable plant. They are used to minimize Differential Mode Delay (DMD) which can occur when a singlemode laser source is launched into the center of a multimode fiber.

The most common use for MCP is long wave Gigabit Ethernet applications (1000BASE-LX) in which a 1310nm single mode transceiver is being deployed into an existing multimode fiber plant. Opterna MCP uses the most reliable offset method that launches laser source away from the center of the multimode fiber. This ensures effective bandwidth for the system, closer to that measured by over-filled launch method.

Opterna MCP assembly offers the same reliability of a standard patchcord. They are available in all connector styles with 2.5 or 1.25mm ferrules and common multimode fiber types (50 & 62.5ìm).

Introduction

• Designed for 1000BASE-LX Transmitters (GbE)

• Available in 50/125 and 62.5/125 fiber options

• Fully compliant with IEEE 802.3z

• Eliminates differential mode delay

• Available in all connector options

• Compact and reliable packaging

• Uses offset method to ensure reliability and are 100% tested for Coupled Power Ratio (CPR)

• Individual test sheet with IL & CPR and unique product identification number for traceability

• RoHS compliant

• Low Insertion Loss & Back Reflection

Features Mode Conditioning Patchcords






OpternaROpternaR


Mode Conditioning Patchcords

• Gigabit Ethernet 1000BASE-LX over multimode cable

Parameter SpecificationDescription 62.5 μm MMF 50 μm MMFOperating wavelength 1310 nmMaximum Insertion loss 0.4 dBCoupled Power Ratio (CPR) 28<CPR<40 dB 28<CPR<40 dBReturn Loss (RL) SM channel >30 dB

MM channel >20 dBOffset between SMF and MMF 17<Offset<23 μm 10<Offset<16 μmConnector finish UPC (RL>50dB) or APC (RL> 60dB)

Ferrule Geometry Radius of Curvature 10 to 25mmApex offset ≤ 50μmFiber height -50 ≤ Ht < 50nm

Maximum Angular Offset 1 DegreeConnector options SC, ST, FC, LC, MU, E -2000, MTRJOperating temperature -40 to + 80°C


Applications:

Specifications:





OpternaROpternaR


Visit: Opterna.com

Parameter SpecificationDescription 62.5 μm MMF 50 μm MMFOperating wavelength 1310 nmMaximum Insertion loss 0.4 dBCoupled Power Ratio (CPR) 28<CPR<40 dB 28<CPR<40 dBReturn Loss (RL) SM channel >30 dB

MM channel >20 dBOffset between SMF and MMF 17<Offset<23 μm 10<Offset<16 μmConnector finish UPC (RL>50dB) or APC (RL> 60dB)

Ferrule Geometry Radius of Curvature 10 to 25mmApex offset ≤ 50μmFiber height -50 ≤ Ht < 50nm

Maximum Angular Offset 1 DegreeConnector options SC, ST, FC, LC, MU, E -2000, MTRJOperating temperature -40 to + 80°C

MC

Fiber Type Connector-Cable Plant

End

Cable Type Equipment End-

MM Leg

Equipment End-

SM Leg

Connector Finish

(SM leg)

Equipment End

Connector Configuration

Length

62 62.5/125 MM

ST ST connector

16 1.6mmduplex

ST ST connector

ST ST connector

U UPC SX Simplex 015 1.5 meter

50 50/125 MM

SC SC connector

18 1.8mmduplex

SC SC connector

SC SC connector

A APC DX Duplex 105 B

SD SC duplex 20 2.0mmduplex

FC FC connector

FC FC connector

Not applicable(blank)

10.5 meter

FC FC connector

28 2.8mmduplex

LC LC connector

LC LC connector

LC LC connector

MU MU connector

MU MU connector

LD LC duplex E2 E-2000connector

E2 E-2000connector

MU MU connector

MT MTRJconnector

If MTRJ(blank)

MD MUduplex

E2 E-2000connector

MT MTRJconnector

Ordering Info:

Mode Conditioning PatchcordsFiber Interconnect

& Passives






OpternaROpternaR

Visit: Opterna.com

MT Modular Cassettes & Adapter Plates

The Opterna® pre-terminated MT cassettes are ideally suited for high density backbone and building entry interconnect applications in data and telecom environments. Manufactured in our state-of-the-art facilities, they offer rapid deployment, high density and maximum space utilization combined with significant time and cost savings. The Opterna MT modular product line is easy to install, upgrade and re-work without affecting the existing connections, which makes it perfect for pay-as-you-grow scenarios.

In addition Opterna also offers a wide range of pass through modular adapter plates for patching and managing pre-terminated fiber optic cables, factory populated with all standard types of adapters.

Introduction

• All modules are LGX compatible

• Available in all fiber types - SM and MM

• 100 % factory terminated and tested - saves times and guarantees high performance

• Up to 24 FO connections in one LGX cassette

• Polarity A (standard), B or C

• Optimized performance using only highest quality connectivity components

• 40 & 100G ready

• Highest quality MT connectivity - MTP® and MTP Elite® connectors

Features Data Center Conectivity MT Modular Cassettes and Adapter Plates

OSP Solutions

DSODCCrev1 1/4





OpternaROpternaR

Visit: Opterna.com

MT Modular Cassettes & Adapter Plates

• Data center and telecommunication networks

• High density connection between active equipment and distribution architectures

• Gigabit Ethernet, Local Area Networks, Wide Area Networks, Storage Area Networks

• Backbone links for CATV and video transmission

Parameter Average IL (dB)Rear connectors MTP or MTP Elite (MPO on request)Front connectors SC, LC (Others on request)Number of rear connectors 1 or 2Number of front connectors Up to 12 SC or 24 LC connectionsFiber types G652D, OM3, OM4 (Others on request)Cassette dimensions (HxWxD) mm 30 x 129 x 132Packed dimensions (HxWxD) mm 50 x 150 x 200

Cassette material Cold rolled steel, powder coatedCassette color Black RAL 9005, available in RAL 7032 and RAL 7035 (Gray) on requestCassette material TIA-604-5, IEC 61754-4, IEC-61754-7, IEC 61754-20, EN50377-15-1,

ISO/IEC 11801, TIA/EIA-568-B, EIA/TIA-526-7&14A, RoHS

Connector type Average IL (dB)* Max IL (dB)* Return loss (dB)MTP Elite (MM) 0.10 0.35 N/AMTP (MM) 0.20 0.60 N/ALC/ SC (MM) 0.20 0.30 N/AMTP Elite (SM) 0.10 0.35 >60MTP (SM) 0.25 0.75 >60LC/ SC (SM) 0.15 0.30 >50(UPC)/60(APC)

OSP Solutions

Applications:

DSODCCrev1 2/4





OpternaROpternaR

Visit: Opterna.com Visit: Opterna.com

Drawing:

104.0

132.0

29.5

128.9

30.2

6.1

15.1

117.3

R5.0

MT Modular Cassettes & Adapter PlatesOSP Solutions

DSODCCrev1 3/4





OpternaROpternaR

Visit: Opterna.com

Ordering information MT modular cassettes:

ODCC

MT Connector

MT Connector Type

Front AdapterType

FiberCount

SleeveMaterial

Fiber Type Adapter color

Metal color

Polarity

ME MTP Elite

A 12F SC SC SX 12 12 M Metal OM3 OM3 GN Green BK Black A A

MT MTP B 24F SD SC DX 24 24 C Zirconia OM4 OM4 BL Blue B B

LD LC DX OS2 G652D BG Beige X Other

LQ LC Quad AQ Aqua

LS LC DX internalshutter

HV HeatherViolet

LH LC quad internalshutter

Ordering information modular adapter plates:

ODCA

AdapterType

Number ofAdapters

SleeveMaterial

Adapter colour

Metal colour

SC SC SX 06 6 M Metal GN Green BK Black

SD SC DX 12 12 C Zirconia BL Blue

LD LC DX Blank plate BG Beige

LQ LC Quad AQ Aqua

LS LC DX internalshutter

HV HeatherViolet

LH LC quad internalshutter

Blank plate

NA Blank plate

Ordering Info:

MT Modular Cassettes & Adapter PlatesOSP Solutions


DSODCCrev1 4/4





OpternaROpternaR

Visit: Opterna.com

MT Modular Patch Panels

The MT modular patch panels are a part of Opterna’s comprehensive MT modular connectivity system for data centers and other. In order to enable the optimum balance between accessibility and density, a range of 1U and 3U fixed and sliding modular solutions are available. All panels are based on the IEC 60297-3 standard.

1U modular panel:The 1U MT modular patch panel is a cost effective solution for routing and patching array fiber optic cables (MTP/MPO). It has 3 slots for loading pre-terminated modular MT cassettes or adapter plates. When fully loaded this panel offers up to 36 SC, 72 LC or 18 MT connections in 1U. Two options are available - fixed and sliding (drawer type).

3U modular panel:The 3U Chassis has 12 slots and provides a very high density solution. It is ideal in situations where floor and rack space utilization is critical and Moves Adds and Changes (MACS) are limited. Although it is a high density solution, the 3U chassis is designed with finger access in mind, striking the optimum balance between space utilization and access. This chassis enables a maximum of 12 cassettes or adapter plates to be installed, offering up to 144 SC or 288 LC connections in 1U.In order to improve the physical security, a lockable metal cover can be installed. The cover also includes a 1U protected cable management duct.

Introduction

• Robust and reliable

• Uses industry approved 19” design and LGX style modules

• Flexible, multi-functional solution for different types of connectivity

• High density combined with ease of installation and maintenance

• No disturbance of existing connections during installation or re-work

• Recessable mounting brackets

Features Data Center Conectivity MT Modular Patch Panels

Central OfficeSolutions

DSODCPrev1 1/4





OpternaROpternaR

Visit: Opterna.com

435.0

396.0

405.0

200.0

83.0

434.0

481.0

176.5 13

2.5

31.8

171.0

270.0

444.0

486.0

43.7

31.8

465.0


3U chassis

Fixed Panel

Drawings:


DSODCPrev1 2/4





OpternaROpternaR

Visit: Opterna.com Visit: Opterna.com

438.2

301.5

483.0

43.0

31.8

Sliding panel

Drawings:

MT Modular Patch PanelsCentral Office

Solutions

DSODCPrev1 3/4





OpternaROpternaR

Visit: Opterna.com





*excluding mounting brackets

Parameter Specification 1U sliding panel High density3U panel

Cover for3U panel

Net Dimension (HxWxD)mm* 44x440x270 44x440x302 133x435x200 171x435x83Packed Dimension (HxWxD)mm 50x530x330 50x530x330 160x460x230 200 x 460 x 150Net Weight (kg) 1.9 3.7 4.2 1.8

Packed Weight (kg) 2.2 4.0 4.5 2.0Number of LGX modules 3 3 12 N/AMaterial Cold rolled steel, powder coatedColor Black RAL 9005, available in RAL 7032 and RAL 7035 (Gray) on request

Operating temperature °C -10 to +60Compliance IEC 60297, RoHS

Part Number DescriptionODCPF13BK Fixed 1U MT Modular patch panel for 3 modules, blackODCPS13BK Sliding 1U MT Modular patch panel for 3 modules, blackODCPF312BK Fixed 3U High density MT Modular patch panel for 12 modules, blackODCPF3CBK Cover for Fixed 3U High density MT Modular patch panel, blackODCPG45BK Gland holder for all MT panels (including gland for 4 cables up to 5mm)


Applications:

Part Numbers:

Copyright 2014, Opterna International Corp. All rights reserved. The information contained herein is subject to change without notice. The Opterna nameand logo are registered trademarks of Opterna Technology Limited.


DSODCPrev1 4/4





OpternaROpternaR


Mt Array Trunk Cable Assemblies™

The Opterna MT trunk cable assemblies are used for high density backbone cabling in data centers and other environments with high fiber density. Manufactured in our state-of-the-art facilities, they offer rapid deployment, high density and maximum space utilization combined with significant time and cost savings. The Opterna MT trunk cable assemblies are available in a wide range of multimode and single mode fiber types. The compact micro tube cables greatly reduce the total volume of cables and help to optimize the cable management.

Introduction

• Standard fiber counts of 12, 24, 48, 72 and 144 fibers, others available on request



• Standard LSZH outer sheath, PE and OFNP available on request

• Standard Polarity A, all other types available on request

• Optimized performance using highest quality connectivity components MTP® Standard and MTP® Elite connectors

• 40 & 100G ready

• 12 or 24 fibers in one compact MT connector

Features Data Center Conectivity MT Array Trunk Cable Assemblies


3/3





OpternaROpternaR


Mt Array Trunk Cable Assemblies™





• High density FTTX applications

Parameter SpecificationFiber count 12F 24F 48F 72F 144FConnectors Female 12 or 24F MTP® or MTP Elite® (MPO on request)Cable type Micro fiber indoor cable with micro tubeFiber types G652D, OM3, OM4 (Others on request)Cable diameter (mm) 3.5 4.6* 10.6* 12.6* 19.5*Cable weight (kg/ km) 12.5 14.6 105 155 336Bending radius 20 x cable diameter (10 x cable diameter without load)

Operating temperature °C 0 to +60Compliance ISO/IEC 60793, ISO/IEC 60794, IEC 60332, TIA-604-5, IEC 61754-7, ISO/IEC 11801,

TIA-568-C, EIA/TIA-526-7&14A, RoHS* Or over sheathed individual 3.5mm 12F cables

Connector type Average IL (dB)* Max IL (dB)* Return loss (dB)MTP Elite (MM) 0.10 0.35 N/AMTP (MM) 0.20 0.60 N/AMT P Elite (SM) 0.10 0.35 >60MTP (SM) 0.25 0.75 >60

* Per mated pair


Applications:

2/3





OpternaROpternaR

DSFC5rev1Visit: Opterna.com Visit: Opterna.com

ODCF ODCF ODCF ODCF ODCF ODCF ODCF

Both Sides Connector

MT Connector Type

Fiber Count Length Excluding Branches (Equal to Total Length If No Branches)

Shortest Branch Length

Fiber Type Polarity

ME MTP Elite

A 12F female

012 12 001 1 Meter

01 0.1 Meter OM3 OM3 A A

MT MTP B 24F female

024 24 010 10Meters

05 0.5 Meter OM4 OM4 B B

B 12F male

048 48 100 100Meters

10 1.0 Meter OS2 G652D X Other

B 24F male

072 72 00 No Branches XXX Other

144 144

XXX Other

Ordering Info:

Mt Array Trunk Cable Assemblies™Central Office

Solutions


3/32/3





OpternaROpternaR

DSODCFrev1Visit: Opterna.com

MT Fanout Cable Assemblies

The Opterna® MT hydra fanout assemblies are used to connect active equipment directly to high fiber count backbone MT cables and MT cassettes in data centers and other high density environments. Manufactured in our state-of-the-art facilities, they offer rapid deployment, high density and maximum space utilization combined with significant time and cost savings. The Opterna MT fanout cable assemblies are available in a wide range of multimode and singlemode fiber types and connectors. The compact microtube cables greatly reduce the total volume of cables and help to optimize the cable management.

Introduction

• Standard fiber counts of 12, 24, 48, 72 and 144 fibers, others available on request



• Standard LSZH outer sheath, PE and OFNP available on request

• Standard Polarity A, all other types available on request

• Optimized performance using highest quality connectivity components MTP® Standard and MTP® Elite connectors

• 40 & 100G ready

• 12 or 24 fibers in one compact MT connector

• Standard 2.0mm color coded fanout with SC and LC connectors, 0.9mm and other types of connectors available on request

Features Data Center Conectivity MT FanoutCable Assemblies


1/3





OpternaROpternaR

DSODCFrev1Visit: Opterna.com

MT Fanout Cable Assemblies





• High density FTTX applications

Parameter SpecificationMT Connectors Female 12 or 24F MTP or MTP Elite (MPO on request)Fanout connectors SC or LC, others available on requestCable type Microfiber indoor cable with microtubeFiber types G652D, OM3, OM4 (Others on request)Cable diameter (mm) 12F - 3.5 24F - 4.6Cable weight (kg/ km) 12.5 14.6Bending radius 20 x cable diameter (10 x cable diameter without load)

Operating temperature °C 0 to +60Compliance ISO/IEC 60793, ISO/IEC 60794, IEC 60332, TIA-604-5, IEC 61754-7,

IEC 61754-4, IEC 61754-20, ISO/IEC 11801, EIA/TIA-526-7&14A, RoHS

Connector type Average IL (dB)* Max IL (dB)* Return loss (dB)MTP Elite (MM) 0.10 0.35 N/AMTP (MM) 0.20 0.60 N/ALC/ SC (MM) 0.20 0.30 N/AMTP Elite (SM) 0.10 0.35 >60MTP (SM) 0.25 0.75 >60LC/ SC (SM) 0.15 0.30 >55(UPC)/60(APC)

* Per mated pair


Applications:

2/3





OpternaROpternaR

DSODCFrev1Visit: Opterna.com Visit: Opterna.com

ODCF ODCF ODCF ODCF ODCF ODCF ODCF ODCF

MT Connector

Type

MT Connector Type

Fan-out connector

Type(APC /UPC/ PC)

Length excluding

Fanout

Shortest Branch Length

Fiber Type Connectorcolor

Polarity

ME MTP Elite

A 12F female

SCA SC/APC SX 010 1 Meter

01 0.1 Meter OM3 OM3 GN Green A A

MT MTP B 24F female

SCU SC/UPC SX 015 1.5 meter

05 0.5 Meter OM4 OM4 BL Blue B B

C 12F male

SCP SC MM SX 150 15 meters

10 1.0 Meter OS2 G652D BG Beige X Other

D 24F male

LCA LC/ APC SX 7A1 G657A1 HV HV

LCU LC/ UPC SX 7A2 G657A2 AQ Aqua

LCP LC MM SX

SDA SC/APC DX

SDU SC/UPC DX

SDP SC MM DX

LDA LC/ APC DX

LDU LC/ UPC DX

LDP LC MM DX

Ordering Info:

MT Fanout Cable AssembliesCentral Office

Solutions


3/32/3





OpternaROpternaR


Fiber Optic Loose Tube Cable

Opterna fiber optic loose tube cable features a central tube design surrounded by glass yarn. This dielectric single jacket central loose tube cable is a UV-stabilized and fully water blocked cable for outdoor duct applications (PE outer jacket) or Indoor/Outdoor applications (LSZH outer jacket).

The loose tube design provides stable and highly reliable transmission parameters for a variety of voice, data, video and imaging applications.

Introduction

• Central loose tube construction

• Lightweight

• Compact design for limited conduit space

• Each fiber is color coded for easy identification

• Glass yarns for limited rodent protection

• LSZH jacket for Indoor/outdoor applications

• RoHS compliant

Features: All Dielectric Single Jacketed Central Tube

OSP Solutions

RipcordOuter Jacket

12-Fiber Cable

24-Fiber Cable

Optical FiberFilling CompoundLoose Buffer tubes

Glass Yarns

RipcordOuter Jacket

Optical FiberFilling CompoundLoose Buffer tubes

Glass Yarns

1/3





OpternaROpternaR



• Building Interconnections (Campus LAN)

• Telcordia GR-20-CORE

• IEC 60793 / IEC 60794

• ITU-T G.652.D

• Fiber - Singlemode OS2 - G.652.D, 62.5μm (OM1), 50μm (OM2,OM3 & OM4) multimode available• Outer jacket : Black UV- and moisture-resistant Polyethylene or LSZH (Low Smoke Zero Halogen)

Applications:

Standards:

Options:

Color of Buffer:


OSP Solutions

Optical Fiber 62.5/125 μmOM1

(850/1300)

50/125 μmOM2

(850/1300)

50/125 μmOM3

(850/1300)

50/125 μmOM4

(850/1300)

9/125 μmOS2

(1310/1550)

Attenuation (dB/km) Typical values 3.5/1.0 3.0/1.0 3.0/1.0 3.0/1.0 0.40/0.30

Minimum Bandwidth (MHz •km) 200/500 500/500 1500/500 3500/500 -

Ethernet Link Distance (m)

10Gbps - - 300 550 -

1Gbps 275/550 550/550 - - -

01 - Blue 07 - Red 13 - Blue / Single dot marking 19 - Red / Single dot marking

02 - Orange 08 - Black 14 - Orange / Single dot marking 20 - Natural

03 - Green 09 - Yellow 15 - Green / Single dot marking 21 - Yellow / Single dot marking

04 - Brown 10 - Violet 16 - Brown / Single dot marking 22 - Violet / Single dot marking

05 - Slate 11 - Rose 17 - Slate / Single dot marking 23 - Rose / Single dot marking

06 - White 12 - Aqua 18 - White / Single dot marking 24 - Aqua / Single dot marking

2/3





OpternaROpternaR



OSP Solutions


Mechanical Characteristics:

Ordering Info:

Shipping Information:

FiberCount

NominalDiameter

NominalWeight

Maximum Tensile Load Crush Load Minimum Bend Radius

Short Term Long Term Short Term Long Term Loaded Installed

[mm] [kg/km] [N] [N] [N/cm] [N/cm] [mm] [mm]

2 6.3 36 1600 800 200 100 130 65

4 6.3 36 1600 800 200 100 130 65

6 6.3 36 1600 800 200 100 130 65

8 6.3 36 1600 800 200 100 130 65

12 6.3 36 1600 800 200 100 130 65

16 6.8 40 1600 800 200 100 140 70

18 6.8 40 1600 800 200 100 140 70

24 6.8 40 1600 800 200 100 140 70

Storage Temperature : -40 to + 75°C / Operating Temperature : -20 to + 70°C

XXX : OS1, OS2, OM1, OM2, OM3, OM4YYY : Number Of cores

*Other Cable lengths may be available upon request

FC-XXX-CLT-GA-YYY-LZ Fiber Optic Single Jacket Central Loose Tube, glass yarn, LSZH jacket

FC-XXX-CLT-GA-YYY-PE Fiber Optic Single Jacket Central Loose Tube, glass yarn, PE jacket

FC-XXX-CLT-GA-YYY-NR Fiber Optic Single Jacket Central Loose Tube, glass yarn, riser rated jacket

FC-XXX-CLT-GA-YYY-NP Fiber Optic Single Jacket Central Loose Tube, glass yarn, plenum rated jacket

Standard Reel Length 4000m

3/32/3





OpternaROpternaR

Visit: Opterna.comDSODB1rev1 1/2

ODB Series 100

Opterna’s Optical Distribution Box (ODB) Series 100 is a robust outdoor-rated enclosure designed for FTTH networks in single dwelling, multi-dwelling and multi-tenant applications, where it serves as a distribution box for up to 8 subscribers.

Available in two sizes, the ODB 100 features an internal swing panel with a rear splice area that accommodates PLC splitters, splices and excess fiber storage. The front face of the swing panel holds SC duplex or LC quad connector adaptors. The ODB 100 can be securely mounted to a surface with 4 screws, accessible only when the cover is open.

Introduction

• Indoor and outdoor applications, IP 55 rated • Compact and light, made of UV resistant polycarbonate • Swing panel design for easy installation and maintenance • Integrated holder for one PLC splitter • Integrated splice tray and fiber management • Distribution cables can be pre-terminated or spliced to pigtails • Lock with protective cap • Connectivity compliance: IEC 61754-4, IEC 61754-20, GR-326 CORE

Features Robust Outdoor-rated Enclosure

OSP Solutions

OpternaROpternaR





Visit: Opterna.comDSODB1rev1 2/2

ODB Series 100

• FTTH networks serving single dwelling, multi-dwelling and multi-tenant buildings

• Wall, pole or pedestal mount

Note: Maximum of 2 Adapters in 1A enclosure.

Splitters, pigtails and additional splice trays are sold separately. Contact Opterna for details.

Applications:

Specifications:

Ordering Info:

OSP Solutions

Parameter Unit 1A enclosure 1B enclosureDimensions (HxWxD) in. 8.1 x 6.3 x 3.6 8.1 x 7.9 x 3.6

mm 206 x 160 x 91 206 x 200 x 91Input Cable ports - 1 PG13.5 (5 to 9mm dia.) 2 PG16 (10 to 14mm dia.)

Output cable ports - 8 (2 to 7mm dia.) 8 (2 to 7mm dia.)Number of adapters - 2 SC duplex or LC quad 4 SC duplex or LC quad

Splitter capacity - 1 2Splice capacity - 10 12

Water and dust resistance - IEC 60529 (IPX5, IP5X)Impact resistance - IEC 62262 (IK08)

Operating temperature - -20 to +65

Color - RAL-7016 (Anthracite Grey)

Enclosure Type Adapter Quantity

Adapter Type

Termination Color

AG

ODB1A 1A enclosure 0 none 0 none 0 none

ODB1B 1B enclosure 1 one SD SC Duplex A APC

2 two LQ LC Quad U UPC

3 three

4 four






OpternaROpternaR

DSPLCrev1

Visit: Opterna.com

PLC Splitters

Opterna’s Planar Lightwave Circuits (PLC) splitters are manufactured using silica glass waveguide circuits and extremely precise alignment of optic fibers in very small package. They split or combine light from one or two incoming fibres to multiple numbers of outgoing fibers. They perform uniformly over a wide spectral range, with ultra-low losses. Opterna splitters are highly compact, reliable and available in very wide range of fiber and connector types. All Opterna PLC splitters are fully compliant with the Telcordia GR-1209 & GR-1221 standard.

Introduction

• Low insertion losses • Ultra-broadband performance (1250-1650nm)

• Low Polarization Dependant Loses (PDL) and Polarization Mode Dispersion (PMD)

• 1 or 2 input channels and up to 64 output channels

• Ultra small, suitable for all applications

• Available with all type of packages and connectors

Features PLC Splitters


1/4





OpternaROpternaR

DSPLCrev1Visit: Opterna.com

PLC Splitters

• FTTx networks

• Optical CATV networks

• CWDM and DWDM systems

• Key element of all PON networks

• LAN and Telecom networks

Parameter Unit 1 x N1 x 2 1 x 4 1 x 8 1 x 16 1 x 32 1 x 64

Insertion Loss Max. dB. 3.8 7.0 10.4 13.9 17.2 22.0

Channel Uniformity Max. dB. 0.6 0.5 0.5 1.4 1.6 2.5

Polarization Dependent Loss Max. dB. 0.2 0.3 0.3 0.3 0.3 0.3

Wavelength Dependent Loss Max. dB. 0.3 0.3 0.3 0.3 0.3 0.3Temperature Dependent Loss Max. dB. 0.5 0.5 0.5 0.5 0.5 0.5

Connector Dependent Loss Max. dB. 0.2 0.2 0.2 0.2 0.2 0.2

Operating Wavelength Min.-Max. nm 1250 ~ 1650

Return Loss Min. dB. 55

Directivity Min. dB. 55

Operating Temperature °C -40 ~ + 85

Storage Temperature °C -40 ~ + 85

Maximum Input Power Max. mW 500

Fiber Type - ITU G.652D or G.657A

Fiber Length Meter 1.0 meter or customized

Connector Type - Customized (SC, SC/APC, LC, LC/APC)

Package Dimension(L x W x H)

Bare Fiber(250 μm)

mm 40x4x4 40x4x4 40x4x4 40x4x4 55x7x4 55x12x4

IntegratedPackage (900μm)

mm 55x7x4 55x7x4 55x7x4 60x12x4 80x23x4.5 120x43x4.5

Cassette mm 100x80x10 100x80x10 100x80x10 100x80x10 100x80x10 100x80x20


Applications:

Specifications:

2/4





OpternaROpternaR

DSPLCrev1Visit: Opterna.comVisit: Opterna.com

Parameter Unit 2 x N2 x 2 2 x 4 2 x 8 2 x 16 2 x 32 2 x 64

Insertion Loss Max. dB. 4.0 7.3 10.7 14 17.5 22.5

Channel Uniformity Max. dB. 0.8 1.0 1.0 1.5 1.8 3.0

Polarization Dependent Loss Max. dB. 0.2 0.3 0.3 0.3 0.3 0.4

Wavelength Dependent Loss Max. dB. 0.3 0.3 0.3 0.3 0.3 0.3Temperature Dependent Loss Max. dB. 0.5 0.5 0.5 0.5 0.5 0.5

Connector Dependent Loss Max. dB. 0.2 0.2 0.2 0.2 0.2 0.2

Operating Wavelength Min.-Max. nm 1250 ~ 1650

Return Loss Min. dB. 55

Directivity Min. dB. 55

Operating Temperature °C -40 ~ + 85

Storage Temperature °C -40 ~ + 85

Maximum Input Power Max. mW 500

Fiber Type - ITU G.652D or G.657A

Fiber Length Meter 1.0 meter or customized

Connector Type - Customized (SC, SC/APC, LC, LC/APC)

Package Dimension(L x W x H)

Bare Fiber(250 μm)

mm 50x4x4 50x4x4 50x4x4 55x7x4 55x7x4 65x12x4

IntegratedPackage (900μm)

mm 65x7x4 65x7x4 65x7x4 75x12x4 80x23x4.5 120x43x4.5

Cassette mm 100x80x10 100x80x10 100x80x10 100x80x10 100x80x10 100x80x20

Name of the test Condition DurationTemperature- Humidity aging 85°C and 85% RH 7 daysVibration 10 - 55Hz, 1.52mm double amplitude, in three axes 1 hour

Component Impact Test Impact of 500g (mass<=0.125kg), 1ms , half sine pulse 2 impacts

Temperature Cycling Test -40°C to + 70°C , Ramp rate: 1°C /min, Dwell time >15min 10 cycles

Temperature- Humidity cycling -40°C to + 85°C , between 10°C and 23°C - 85% RH, at 85°C -20%RH,between 23°C and 85°C - maintain a linear change in RH,below 10°C - uncontrolled RH

14 days

Water Immersion 43 ± 2°C , PH 5.5 ± 0.5 7 days

Fiber Side Pull test 0.23 kg load, 90° angle , 2 directions 5 seconds

Fiber Side Pull test 0.45 Kg load for Single Input Fiber , 1.5 Kg load for8 Fiber Ribbon Outputs

5 seconds

Specifications:

Telcordia 1209 & 1221 Test results:

PLC SplittersCentral Office

Solutions

3/42/4





OpternaROpternaR

DSPLCrev1Visit: Opterna.com

Ordering Info:


PLC Splitters

PLC PLC PLC PLC PLC PLC PLC PLC PLC

SplitRatio

PackageType

Inputconnector

Type

OutputConnector

Type

InputFiberType

OutputFiberType

InputFiberType

OutputFiberType

FiberType

102 MTP Elite A Integrated SCU SC/UPC SCU 12 0 250 0 250 05 0.5m 05 0.5m OS2 G652D fiber

104 1x2Splitter

B Plastic case100x45x10mm

SCA SC/APC SCA 24 9 900 μm 9 900 μm 10 1.0m 10 1.0m 7A1 G657A1 fiber

108 1x4Splitter

C Plastic case100x80x10mm

LCU LC/UPC LCU LC/UPC 2 2 mmLSZH

2 2 mmLSZH

50 5.0m 50 5.0m 7A2 G657A2 fiber

116 1x16Splitter

D Bare fibersplitter

LCA LC/APC LCA LC/APC X Custom R μmribbon

132 1x32Splitter

F FDH PLCmodule

FCU FC/UPC FCU FC/UPC X Custom

164 1x64Splitter

X For customtype

FCA FC/APC FCA FC/APC

202 2x2Splitter

Noconnector

Noconnector

204 2x4Splitter

XXX Custom XXX Custom

208 2x8Splitter

216 2x16Splitter

232 2x32Splitter

264 2x64Splitter


4/4





OpternaROpternaR

Visit: Opterna.comDSPTrev1 1/3

Opterna offers a complete range of pre-terminated multi-fiber assemblies in a variety of cable and connector configurations. Our high-quality factory terminated and tested assemblies are used for simple point to point links or to install a complete fiber optic network.

The cabling is fully compatible with all standard cable management accessories and requires no special tools or expertise to install. The cables are fitted with a protective gland to protect the connectors during installation and a special pulling head that is attached to the cable strength member allows the cable to be pulled through ducts without applying load to the terminations.

Pre-terminated assemblies can also be customized to cater the customer’s specific performance requirement, application migration plan and installation environment.

Introduction

• Fiber count up to 48 fibers

• Available in Multimode and Singlemode fiber types

• Available with indoor and outdoor cable types

• Available with all fiber connector types

• Fully tested, labeled and documented• Improved link loss budget

• Excellent tensile load resistance to facilitate cable pulling through ducts and rails

• Pulling sock at pulling end allows easiness to pull cable through race tracks

• Easy, quick and cost efficient installation

• RoHS compliant

• Complies with international telecom standards

Features Pre-terminated Multi-core Fiber Optic Assembly


Pre-terminated Fiber Optic Assembly





OpternaROpternaR


Pre-terminated Fiber Optic Assembly

• Inter-building and Intra-building backbones for Local Area Network, Data Center, Premise and Campus applications

• Data center main, horizontal, zone and equipment distribution area trunk cables for Storage Area Network (SAN) applications

Fiber Count 2, 4, 6, 8, 12, 16, 24, 48Fiber Types OM1, OM2, OM3, OM4, G652D, G657ACable Type Tight buffered (indoor)

Steel Type Armored (indoor and specific outdoor)Loose Tube (Outdoor application with water resistance

Branch out types Staggered (as in fig. 1 below) or Fan-out (equal branch lengths)Connector Types SC, FC, ST, LC, MU, E2000 (in UPC & APC finish)Specification of gland used for standard assemblies

M20 X 1.5 (other gland size available) – color: black/ grey

Insertion Loss of each termination Max: 0.50dB; Typ: 0.30B

Return Loss of each assembly (for Singlemode) >50dB for UPC>60dB for APC

Max Tensile Load 1500NPackaging Coiled and bagged for assemblies < 50m

Coiled on a drum for assemblies > 50m


Applications:

Size & Dimmensions:

Specifications:





OpternaROpternaR


Visit: Opterna.com

PT

ConnectorPulling End

ConnectorFinish

FiberCount

Fiber Type Cable Type CableJacket

Connector - NonPulling End

ConnectorFinish

Cable Length(L)

Shortest BranchLength

(L1 & L2)*

Branch CableColour

ST ST P PC 02 2

Fiber

OM1 62.5/125

MM

TB 0.9mm

Tight

Buffered

L LSZH ST ST P PC 001 1

meter

03 0.3 meter BK Black

SC SC

simplex

U UPC 04 4

Fiber

OM2 50/125

MM

LT Loose tube V PVC SC SC

simplex

U UPC 010 10

meter

30 3.0 meter YL Yellow

SD SC

duplex

A APC 06 6

Fiber

OM3 50/125

MM

BO 2mm Break

Out cable

E PE SD SC

duplex

A APC 100 100

meter

WH White

FC FC 08 8

Fiber

OM4 OM4

Fiber

E RISER FC FC No

Connecter

OR Orange

LC LC

simplex

10 10

Fiber

OS2 G652 D E PLENUM LC LC

simplex

AQ Aqua

LD LC

duplex

12 12

Fiber

7A1 G657 A1 LD LC

duplex

HV Heather

Violet

MU MU 16 16

Fiber

7A2 G657 A2 MU MU

E2 E2000 24 24

Fiber

E2 E2000

MT MTRJ 48 48

Fiber

MT MTRJ

No

connector

Ordering Info:

Pre-terminated Fiber Optic AssemblyFiber Interconnect

& Passives


Length of Assembly (gland to gland OR free end to gland) – L L ± 1.0 (m)

Length of shortest branch at pulling end (for staggered assembly) – l₁ 30cms (unless specified)

Length of shortest branch at non-pulling end (for staggered assembly)– l₂ 30cms (unless specified)

Incremental length between branches (for staggered assembly) – l l ± 3cms





OpternaROpternaR

DSCAB3rev1 1/2

Visit: Opterna.com

WALL MOUNT CABINETS - RECESSED

Opterna recessed cabinet are the administration and distribution point for voice, fax, data networking, video entertainment, internet access and all other voice / data / video home solutions. This versatile cabinet flush mounts to a wall.

The cabinets are designed to hold FTTx equipment comfortably. Opterna recessed cabinets are designed to hold 19” rack mounted equipment and are also available in non 19” formats. The cabinet features a lockable glass door, adjustable front profiles and removable gland plates at the top and bottom. Two different versions are available, fixed design and removable front cover.

Introduction

• Constructed with rigid frames that can be fitted on a wall

• Adjustable mounting rails in the front for 19” formats

• Top and bottom cable entry facility for easy cable installation

• Front section with tempered glass door and lock

• Good ventilation and heat dispersion

Features Wall Mount Cabinets- Recessed

MDU Solutions





OpternaROpternaR

DSCAB3rev1 2/2

Visit: Opterna.com

Wall Mount Cabinet, Single Section

• Designed for installations that comply with the

EN 50173-1, EN 50174-1 & 2,ISO/IEC 11801, ANSI/TIA/EIA-568-C

• FTTx

Standard

• Comply with mounting dimensions to IEC 297-3 and

DIN - 41494 for all equipments

Material

• SPCC cold rolled steel

• Mounting profiles - 1.2mm

• Other elements - 1.0 mm

• Front door : Tempered glass or Metal

Surface Finish

• Powder coated

Applications:

Technical Specification:

Ordering Info:

MDU Solutions


X : S - Fixed design, without outer frameD - With removable outer frame

Part Number Description Height (mm)

Width (mm)

Depth (mm)

CAB-RWM-12-600-150-X-G Recessed Single Section Cabinet, 12U, 600mm (W)x 150mm(D), Glass Door

WMS WMS WMS

CAB-RWM-12-600-300-S-G Recessed Single Section Cabinet, 12U, 600mm (W)x 300mm(D), Glass Door

WMS WMS WMS

CAB-RWM-600-425-120 Recessed Single Section Cabinet, 600(H) x 425(W) x 120(D) WMS WMS WMS





OpternaROpternaR

Visit: Opterna.comDSFCSrev1 1/2

Shuttered SC Patch Cables

Even when using shuttered fiber optic adapters in FTTH deployment there is a risk of accidental exposure to laser light: when the patch cable on the premises side is connected to the wall outlet but unplugged from the active equipment (ONT or ONU) the standard SC patch cables do not offer any protection. The Opterna shuttered SC patch is a unique products developed for FTTH and FTTD application. It has a spring loaded mechanism inside which secures the patch cable immediately after it is disconnected and this way eliminates this treat of exposure to the invisible laser light. Like all the The Opterna patchcords & pigtails the shuttered SC patch cords are manufactured in state-of-the-art controlled manufacturing processes to operate over a wide range of wavelengths ranging in 1310 and 1550nm windows with guaranteed low loss and reliability. Each patch cord is individually tested and supplied with test certificates. The unique serial number gives provides traceability of every single product and ensures supreme quantity.

Introduction

• Especially designed for FTTH/ FTTD applications at customers’ premises

• Product without analogue

• High quality connectors with reliable mechanism

• Low insertion loss and high Return loss

• Individual test results and unique trace number provided with every product

• High mating durability

• RoHS compliant

• Compliant with IEC 61754-4 Standar

Features Shuttered SC Patch Cables






OpternaROpternaR

Visit: Opterna.comDSFCSrev1 2/2

Shuttered SC Patch Cables

• FTTH deployments

• FTTD deployments


Applications:

Specifications:

Optical Performance Specification:

Ordering Info:

Parameter SpecificationFiber Types 62.5/125 (OM1), 50/125 (OM2), OM3, OM4, G652D, G657A & B

Cable Types Simplex, 3.0mm

Connector Types SC

Endface Finish PC, UPC, APC

Parameter Type of connector MeasuresParameter Multimode SC Max: 0.30db; Typical: 0.20dB

Singlemode SC Max: 0.30db; Typical: 0.20dB

Return Loss (Singlemode) Singlemode UPC endface finish type Min: 50dB; Typical 55dB

Singlemode APC endface finish type Min: 55dB; Typical 60dB


FCSPC FCSPC FCSPC FCSPC FCSPC

Connector TypeBoth Ends

Connector FinishBoth Ends

Fiber Type Cable Length Cable Colour

SC SC Simplex A APC OM2 FC Style 100 10 meter YL Yellow

U UPC OM3 SC Style WH White

OM4 ST Style OR Orange

OS2 LC Style HV Heather Violet

7A1 MU Style AQ Aqua

7B2 G657B2





OpternaROpternaR

Visit: Opterna.comDSSADrev1 1/3

Fiber Optic Shuttered Adapters

The Opterna shuttered adapters are designed specially to suit the high safety requirements of the FTTH networks. The shutters are designed to prevent ingress of dust and accidental laser exposure. The spring loaded shutters will remain closed when the connector is unplugged and prevents exposure to laser. All adapters are manufactured in standard colors for identifying UPC and APC end face finishing of the connectors. Opterna fiber optic adapters are manufactured strictly according the international standards, fully compatible with all types of equipment. The Opterna shuttered adapters have the same high quality optical performance as the standard non shuttered ones.

Introduction

• High performance UPC and APC adapters

• Standard rear side blue and green color

• SC Simplex, SC duplex and LC Duplex versions available

• White shutter side to suit the color of faceplate

• Bottom to top opening of shutter which makes thelaser caution label visible to the user

• Low insertion loss – under 0.2dB(connector performance dependent)

• Return loss >50dB (UPC) and >60dB(APC)

• High mating durability (<0.2dB change after 1000 cycles)

• Very wide temperature range of using (-40 to +80°C)

• RoHS compliant

Features Fiber Optic shuttered Adapters






OpternaROpternaR


Fiber Optic Shuttered AdaptersFiber Interconnect

& Passives

Applications:

Size and dimensions:

• All types of connection interface (ODF, wall mounted solutions etc.)

• FTTH deployments

• CATV, WAN, LAN and Telecom networks

• Testing and measurement equipment

SC Simplex adaptor (all dimensions in mm)

LC Duplex adaptor (all dimensions in mm)





OpternaROpternaR


Visit: Opterna.com

SAD

Adapter type End facefinish type

Sleeve type HousingColor

Shutter color Flanges Shutter type(for duplex)

SC Simplex SC U UPC C Zirconia BL Blue BL Blue F WithFlanges

S Oneshutter

SD Duplex SC A APC M Metal GN Green GN Green N Reducedflanges

E Individualshutters

LD Duplex LC P PC BG Beige BG Beige

WH White

MT Metal

Ordering Info:

Fiber Optic Shuttered AdaptersFiber Interconnect

& Passives






OpternaROpternaR


Fiber Optic Multi Loose Tube Cable

Opterna single jacket single armor loose tube fiber optic cable provides stable and highly reliable transmission parameters for a variety of voice, data, video and imaging applications.

The cable offers durability and flexibility required for many outside plant uses where added compressive strength, rodent resistance.

RoHS (Restriction of the use of Certain Hazardous Substances Directive) Complied.

Introduction

• Multi loose tube construction

• Each fiber is color coded for easy identification

• Color coded loose tubes for easy identification

• LSZH jacket for Indoor/outdoor applications

Features: Single Jacket Single Armor Multi Loose Tube

OSP Solutions

Optical FiberJelly CompoundLoose Buffer TubesCentral Strength MemberWater Blocking Yarn or JellyCore Wrapping Tape

Outer Strength Member

Water Blocking TapeRipcordCorrugated Steel Tape ArmorOuter PE/LSZH Jacket

72-Fiber Cable

1/3





OpternaROpternaR



• Building Interconnections (Campus LAN)

• FTTx & Telecommunications Networks

• Telcordia GR-20-CORE

• IEC 60793 / IEC 60794

• IEC 60332-1,3

• IEEE 383

• Fiber - Singlemode OS2 - G.652.D, 62.5μm(OM1), 50μm (OM2, OM3 & OM4) multimode available

Applications:

Standards:

Options:

Color of Buffer:


OSP Solutions

Optical Fiber 62.5/125 μmOM1

(850/1300)

50/125 μmOM2

(850/1300)

50/125 μmOM3

(850/1300)

50/125 μmOM4

(850/1300)

9/125 μmOS2

(1310/1550)

Attenuation (dB/km) Typical values 3.5/1.0 3.0/1.0 3.0/1.0 3.0/1.0 0.40/0.30

Minimum Bandwidth (MHz •km) 200/500 500/500 1500/500 3500/500 -

Ethernet Link Distance (m)

10Gbps - - 300 550 -

1Gbps 275/550 550/550 - - -

01 - Blue 05 - Slate 09 - Yellow

02 - Orange 06 - White 10 - Violet

03 - Green 07 - Red 11 - Pink

04 - Brown 08 - Black 12 - Aqua

2/3





OpternaROpternaR



OSP Solutions


Mechanical & Environmental:

Ordering Info:

Shipping Information:

FiberCount

NominalDiameter

NominalWeight

Maximum Tensile Load Crush Load Minimum Bend Radius

Short Term Long Term Short Term Long Term Loaded Installed

[mm] [kg/km] [N] [N] [N/cm] [N/cm] [mm] [mm]

6 12.7 157/215 2,700 1000 220 110 254 127

12 12.7 157/215 2,700 1000 220 110 254 127

24 12.7 157/215 2,700 1000 220 110 254 127

36 12.7 157/215 2,700 1000 220 110 254 127

48 13.2 163/223 2,700 1000 220 110 264 132

72 13.2 163/223 2,700 1000 220 110 264 132

96 14.3 190/260 2,700 1000 220 110 286 143

120 15.8 225/308 2,700 1000 220 110 316 158

144 17.2 260/356 2,700 1000 220 110 344 172

228 18.0 279/382 2,700 1000 220 110 360 180

276 19.2 319/437 2,700 1000 220 110 384 192

300 19.9 340/466 2,700 1000 220 110 398 199

Storage Temperature : -40 to + 75°C / Operating Temperature : -20 to + 70°C

*Denotes norminal value for PE / LSZH Jacketed Cable.

XXX : OS1, OS2, 7A1, 7A2, 7B2, 7B3, 655, OM1, OM2, OM3, OM4YYY : Number of Cores

*Other Cable lengths may be available upon request

FC-XXX-MLT-SA-YYY-PE Fiber Optic Single Jacket Armor Multi Loose Tube, PE jacket

FC-XXX-MLT-SA-YYY-LZ Fiber Optic Single Jacket Armor Multi Loose Tube, LSZH jacket

Standard Reel Length 4000m

3/32/3





OpternaROpternaR

Visit: Opterna.com

Sliding Fiber Optic Patch Panel

The Opterna Fiber Optic 19” Sliding Patch Panel has been designed to facilitate internal fiber management and also to maximize fiber density in 1U, 2U heights.

The sliding tray provides easy access to fiber cabling, making this panel ideal for ‘Pay as you Grow’ applications. The mild steel construction and its black or grey powder coated finish makes this panel a high quality solution for any fiber optic installation, including Data Centers, FTTX and Telecommunications.

The panel supports 24 way and 48 way configurations in SC Simplex, SC Duplex, ST/FC (D cut out), LC Duplex (SC simplex foot print), LC Quad (SC Duplex foot print). Versions are available with MTP MPO cutouts on the back for use with pre-terminated MTP/MPO trunks.

Introduction

• Can be installed within standard 19” racks and wall mounted enclosures according to IEC 297-3 specification

• The universal design allows using both splice trays with one (central) and with two pins

• Rear of panel offers a range of apertures to accommodate a variety of gland configurations

• Optimum balance between panel depth and fiber management

• The base panel is designed for customized fiber management and splicing solutions

• Various anchoring points for incoming cables

• Front face of the panel includes a port identification strip

• Fiber management kits and splice cassette are offered as accessories

• All panels are available pre-loaded with adapters, pigtails and splice accessories

Features Sliding Fiber Optic Patch Panel

OSP Solutions

DASFPrev1 1/5





OpternaROpternaR

Visit: Opterna.com


• Offers solution for optical splicing and patching

• Specifically designed for Data Center, communications room and telecommunication applications

OSP Solutions

Applications:

Drawing:

235.2

438.2 415.0

483.0

31.8

43.0

43.5

465.5

1

2 4

7

6

ITEM NO. PART NUMBER QTY.1 1SMP-538-1-LID-R3 12 1SMP-538-2-1U-BRACKET-R3 23 1SMP-538-10-INNER-ADAPTER-PLATE-24SC-R3 1

4 1SMP-538-9-SLIDING-TRAY-24SC-ASSY-R3 1

5 NYLATCH 2

6 Washer ISO 7089 - 4 4

7 ISO 7045 - M4 x 8 - Z --- 8N 4

DASFPrev1 2/5





OpternaROpternaR


Ordering info:

Ordering information for panel without MTP/MPO cutouts on the back

Part Number Item Description

FP-SL-SCDX-012-1B Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way 12 SC Duplex cut out, Black color

FP-SL-SCSX-024-1B Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way 24 SC Simplex cut out, Black color

FP-SL-SCDX-024-1B Fiber Optic 19” 1U Unloaded Sliding Patch Panel 48 way 24 SC Duplex cut out, Black color

FP-SL-SCSX -048-2B Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way 48 SC Simplex cut out, Black color

FP-SL-DCSX-024-1B Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24way 24 ST/FC Simplex D cut out, Black color

FP-SL-DCSX-048-2B Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way, 48 ST/FC Simplex D cut out, Black color

FP-SL-SCDX-012-1G Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way,12 SC Duplex cut out, Gray color.

FP-SL-SCSX-024-1G Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way, 24 SC Simplex cut out, Gray color

FP-SL-SCDX-024-1G Fiber Optic 19” 1U Unloaded Sliding Patch Panel 48 way, 24 SC Duplex cut out, Gray color

FP-SL-SCSX-048-2G Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way, 48 SC Simplex cut out, Gray color

FP-SL-SCDX-024-2G Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way, 24 S C Duplex cut out, Gray color

FP-SL-DCSX-024-1G Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way, 24 ST/FC Simplex D cut out, Gray color

FP-SL-DCSX-048-2G Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way, 48 ST/FC Simplex D cut out, Gray color


DASFPrev1 3/5

OSP Solutions





OpternaROpternaR

Visit: Opterna.com

Ordering info:

Sliding Fiber Optic Patch PanelOSP Solutions

Ordering information for panel with MTP/MPO cutouts on the back


FP-SL-SCDXM-012-1B Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way 12 SC Duplex cut out, Black color

FP-SL-SCSXM-024-1B Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way 24 SC Simplex cut out, Black color

FP-SL-SCDXM-024-1B Fiber Optic 19” 1U Unloaded Sliding Patch Panel 48 way 24 SC Duplex cut out, Black color

FP-SL-SCSXM -048-2B Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way 48 SC Simplex cut out, Black color

FP-SL-DCSXM-024-1B Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24way 24 ST/FC Simplex D cut out, Black color

FP-SL-DCSXM-048-2B Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way, 48 ST/FC Simplex D cut out, Black color

FP-SL-SCDXM-012-1G Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way,12 SC Duplex cut out, Gray color

FP-SL-SCSXM-024-1G Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way, 24 SC Simplex cut out, Gray color

FP-SL-SCDXM-024-1G Fiber Optic 19” 1U Unloaded Sliding Patch Panel 48 way, 24 SC Duplex cut out, Gray color

FP-SL-SCSXM-048-2G Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way, 48 SC Simplex cut out, Gray color

FP-SL-SCDXM-024-2G Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way, 24 S C Duplex cut out, Gray color

FP-SL-DCSXM-024-1G Fiber Optic 19” 1U Unloaded Sliding Patch Panel 24 way, 24 ST/FC Simplex D cut out, Gray color

FP-SL-DCSXM-048-2G Fiber Optic 19” 2U Unloaded Sliding Patch Panel 48 way, 48 ST/FC Simplex D cut out, Gray color

DASFPrev1 4/5





OpternaROpternaR

Visit: Opterna.com

Visit: Opterna.com

Accessories:


OSP Solutions



OPFC-STGR24 Universal Opterna Splice Tray for two splice holders, unloaded

OPFC-STGR24-L Cover for OP-FC-STGR-24

OPFC-STGR24-CH Holder for 12 metal crimp splice protectors

OPFC-STGR24-SH Holder for 6 heat shrink splice protectors

OPFC-STGR24-CH Stacking hinge for OPFC-STGR24

FP-AC-ST-12 12 way Stackable Splice Tray with Splice Holder and cover

FP-AC-ST-24 24 way Stackable Splice Tray with Splice Holder, Clear Cover

FP-AC-SB-24 24 way Splice Bridge with Adhesive Strip and Cover

FP-AC-CG-11B PG11 (4.5-10mm) Size Cable Gland & Back Nut, Black Nylon LSF material

FP-AC-BC Bunny Clip

FP-AC-FMK Fiber Management Kit consists of 1 x FP-AC-SB-24, 1 x FP-AC-CG-11 and 8 x FP-AC-B

FP-AC-BLNK-SCSX SC Simplex Blank cover

FP-AC-BLNK-SCDX SC Duplex Blank cover

FP-AC-BLNK-DCSX ST/FC Simplex Blank cover

PSCL-600-15-30 60mm Clear Fusion Splice Protector Sleeve

DASFPrev1 5/5





OpternaROpternaR

Visit: Opterna.com

Telescopic Fiber Patch Panel

The telescopic fiber optic patch panel offers excellent flexibility during mounting and installation. Mainly used for distribution and splicing of feeder or distribution fiber cables. The patch panel features an improved staggered adaptor design for easy access to the connectors and patch cords during maintenance and fiber patching.

A sliding telescopic tray feature is incorporated to facilitate easy access for maintenance and also allows the tray to be released from the patch panel for maintenance. The telescopic patch panel is constructed of high quality steel that makes it study and durable. The panel is powder coated to ensure durability.

Introduction

• 1U, 2U, 3U, 4U design

• Telescopic tray can be fully ejected for easy splicing

• 300mm depth for extra storage

• High quality locking system

• Angled cable entries to maintain bend radius

• Strength member lug for securing the central strength member

• Splice tray for terminating incoming fibers to pigtails

• Staggered port design for easy patching

• Port identification on front panel

Features Telescopic Fiber Patch Panel


DSFP3rev1 1/3





OpternaROpternaR

Visit: Opterna.com

Telescopic Fiber Patch Panel

Applications:

Specifications:


DSFP3rev1 2/3

• LAN/WAN

• FTTx

• Telecommunications

• CATV

Mounting Dimensions 19” according to IEC 297-3 specification

Cable Entry 1U PG 16, 2 Ports2U PG 16, 2 Ports3U PG 16, 2 Ports4U PG 21, 2 Ports

Panel Dimensions 1U – 43 mm(H) x 439 mm(W) x 311.5 mm(D)2U – 88 mm(H) x 439 mm(W) x 311.5 mm(D)3U – 132 mm(H) x 439 mm(W) x 311.5 mm(D)4U – 177 mm(H) x 439 mm(W) x 311.5 mm(D)

Adaptor SC Duplex, SC Simplex, ST/FC

Sliding Mechanism Telescopic Rails

Body Construction 1.2mm Steel Sheet

Powder Coated Paint RAL 7032





OpternaROpternaR

Visit: Opterna.com

Visit: Opterna.com

Ordering Info:

Telescopic Fiber Patch PanelCentral Office

Solutions

DSFP3rev1 3/3


FP-SLTR-SCSX-024-1G Telescopic 24 Way Fiber Patch Panel, 1U 24 SC Simplex cutout

FP-SLTR-SCDX-012-1G Telescopic 24 Way Fiber Patch Panel, 1U 12 SC Duplex cutout

FP-SLTR-DCSX-024-1G Telescopic 24 Way Fiber Patch Panel, 1U 24 ST/FC Simplex, D cutout



FP-SLTR-DCSX-048-2G Telescopic 48 Way Fiber Patch Panel, 2U 48 ST/FC Simplex, D cutout



FP-SLTR-DCSX-072-3G Telescopic 72 Way Fiber Patch Panel, 3U 72 ST/FC Simplex cutout



FP-SLTR-DCSX-096-4G Telescopic 96 Way Fiber Patch Panel, 4U 96 ST/FC Simplex cutout

Related Accessories:

SP-TR-1224-BK 12 way stackable splice tray with splice holder and Cover, 180 mm (L) x 113 mm(L) x 13 mm (H)

SP-TR-1224-WH 24 way stackable splice tray with splice holder and Cover, 225 mm (L) x108 mm(W) x 13 mm (H)

SP-TR-1224-BL 24 way stackable splice tray with splice holder and Cover, 160 mm (L) x 105 mm(W) x 10 mm (H)

FP-AC-SB-24 24 way Splice Bridge with Adhesive Strip and Cover

FP-AC-CG-11B PG11 (4.5-10mm) Size Cable Gland & Back Nut, Nylon, Black

FP-AC-CG-16B PG16 (4.5-10mm) Size Cable Gland & Back Nut, Nylon, Black

FP-AC-BC Bunny Clip

FP-AC-FMK Fiber Management Kit consists of 1 x FP-AC-CG-16 and 8 x FP-AC-BC

FP-AC-BLNK-SCSX SC Simplex Blank Cover

FP-AC-BLNK-SCDX SC Duplex Blank Cover

FP-AC-BLNK-DCSX ST/FC Simplex Blank Cover


Documents

Opterna datasheets 2