OptiX OSN 500 Configuration Manual

Release Notes

Contents

OptiX OSN 500Configuration Manual4

Issue1.7

Date2013-11

DOCPROPERTY Confidential

HUAWEI TECHNOLOGIES CO., LTD.

Copyright Huawei Technologies Co., Ltd. 2013. All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.All other trademarks and trade names mentioned in this document are the property of their respective holders.NoticeThe purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied.The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.

Address:Huawei Industrial BaseBantian, LonggangShenzhen 518129People's Republic of China

Website:http://www.huawei.com

Email:[email protected]

About This DocumentChange History

IssueDateDescriptionAuthor

1.002009-01Completed the initial draft. Li Ting/47533

1.032010-3-31Added information about how to install a chassis.Li Ting/47533

1.062011-01-25 Added OptiX OSN 500 V100R005C00 boards. Modified the configuration principle for delivery inspection reports. Description about the EM6 boards Configuration principles for the items with a prefix part number of 0501 and 0511 Document header Configuration principles for blank labels Configuration principles for the concrete floor mount kit Information about the OptiX OSN 500 V100R005 Software pricing for the IEEE 1588v2 featureHe Tao/49403

1.072011-01-25Modified the document based on review commentsHe Tao/49403

1.082011-02-18 Rectified the information about FE and GE ports. Added chassis figures for the OptiX OSN 500 V100R005C00.He Tao/49403

1.102011-10 Added V100R005C02. Added the description about that TDM ports are quoted separately. Added the TNH2 board. The sales of the TNH1 board are controlled. Added the typical configurations of enterprise networks, one-case delivery, and typical configured materials for the Indian market. Deleted typical configurations for China, and typical auxiliary packages for China and overseas.He Tao/49403

1.112012-01-04 Modified the Optical module of EM6F

Deleted TNH1 board, can be replaced by the TNH2 boardHe Tao/49403

1.202012-04 Added V100R006C00

Modified the typical configure of enterprise network Added optical transceiver of EM6F The cabinet doors are delivered in bulks Add UPMs batteryHuang Qian/57692

1.212012-05 Modified the document based on review comments Add 04120309 cablesHuang Qian/57692

1.32012-08 Add cool-air ISU board, and delete typical configuration.Huang Qian/57692

1.42012-11 Added V100R006C00

Modified the typical configure of enterprise networkHuang Qian/57692

1.52013-01 Modeified documents of V100R006C00 Added EF8F board for V100R006C01Huang Qian/57692

1.62013-04 Added V100R007C00

Added Wrist Strap Modifiey the batteries:delete 02230CTX Added the packet of delivery accessory for IndiaHuang Qian/57692

1.72013-11 EF8F board added Electrical ModuleHuang Qian/57692

ContentsiiAbout This Document

11 Product Overview

11.1 What's the OptiX OSN 500

21.2 Product Specifications

21.2.1 About the Chassis

21.2.2 Slot Layout

51.2.3 Service Types

51.2.4 Cross-Connect Capacity

51.2.5 Maximum Number of Received Services

61.3 Product Portfolio

82 NE Software Configurations

82.1 Typical Configurations

102.2 Chassis

112.2.2 ISU

182.2.3 CSHD

202.3 Interface Boards

202.3.1 SL1D

212.3.2 EGT1

222.3.3 SP3D

232.3.4 PL3T

242.3.5 EFS8

242.3.6 EM6T

252.3.7 EM6F

272.3.8 MD1

272.3.9 CQ1

292.3.10 EF8F

302.4 External Components

302.5 Software Package

312.6 Commissioning Accessories

333 Auxiliary Materials

333.1 Cabinet Suite

363.2 Orderwire Phone

373.3 Batteries

383.4 Installation Tools

394 Installation Materials

394.1 Typical Material Package

394.2 External Cable Suite

394.2.1 External Power Cables

424.2.2 E1 Cables

424.2.3 E3/T3 Cables

434.2.4 Others

434.3 External Optical Fiber Suite

434.3.1 Optical Fibers

434.3.2 Optical Attenuators

444.3.3 Fiber Adapters

454.4 Accessories

454.4.1 Software Packages

464.4.2 Auxiliary Materials

524.4.3 Installation kit

535 Documentation

546 Packaging Materials

557 Software Packages

578 License

1 Product Overview1.1 What's the OptiX OSN 500

The OptiX OSN 500 is Huawei's new-generation optical transmission equipment. Being used at the access layer of the transmission network. The equipment supports two forms (STM-1/4 optical ports or GE optical ports), and forms an entire equipment group with other access layer equipment, optimizing the Huawei OptiX product series.Figure 1-1 Product positioning and typical application of the OptiX OSN 500

The OptiX OSN 500 is case-shaped equipment. The dimensions of the chassis are: 44 mm (H) x 442 mm (W) x 220 mm (D). Of a simple architecture and high integration, the OptiX OSN 500 can be installed in the following ways: Cabinet-mounting (ETSI cabinet and 19-inch cabinet)

Wall-mounting

Desk-mounting1.2 Product Specifications

1.2.1 About the Chassis

AppearanceThe OptiX OSN 500 is 1 U high case-shaped equipment that provides two layers of slots for boards. Two extended slots are provided for flexible configurations. The OptiX OSN 500 supports 48 V/60 V DC power or 110 V/220 V AC power. Natural heat dissipation and fan cooling dissipation are available. The following figures show the appearance of the OptiX OSN 500.Figure 1-1 Appearance of the OptiX OSN 500 (48 V/60 V DC power)

Figure 1-2 Appearance of the OptiX OSN 500 (110 V/220 V AC power)

FunctionsThe chassis consists of the following parts: System control and communications board slot area: resides in the lower part of the chassis and houses the ISU/CSHD board. Extended slot area: resides in the upper part of the chassis and houses extended boards. Power board slot area: resides in the left part of the chassis, and houses the power board, each of which is configured with two power cables. The power board provides two 48 V/60 V power inputs or one 110 V/220 V power input, in 1+1 backup mode. Fan board slot area: The chassis powered by 48 V/60 V DC power uses the natural dissipation or air cooling design. The DC-power and air-cooling chassis has a filler panel but not a fan board installed in its fan slot. The AC-power chassis has a fan board installed in its fan slot.1.2.2 Slot Layout

The OptiX OSN 500 is 1 U high case-shaped equipment, and provides three slots, as shown in the following figure.Figure 1-1 Slot layout of the OptiX OSN 500

Slot 3 and slot 4 are reserved for extended boards. Slot 2 houses a functional board integrating the system control unit, cross-connect unit, timing unit, tributary unit, data unit, and line unit. The functional board is available in multiple types depending on the functions and access capacities required for the OptiX OSN 500.Boards Supported by V100R002C01

BoardDescriptionPortValid Slot

ISU boardTNH1ISUAIntegrates the system control unit, cross-connect unit, timing unit, tributary unit, line unit, and transparent data transmission unit. The port impedance is 120 ohms.2xSTM-1/4 optical ports21xE1/T1 electrical ports

8xFE electrical portsSlot 2

TNH1ISUBIntegrates the system control unit, cross-connect unit, timing unit, line unit, and tributary unit. The port impedance is 120 ohms.2xSTM-1/4 optical ports 21xE1/T1 electrical portsSlot 2

TNH1ISUCIntegrates the system control unit, cross-connect unit, timing unit, tributary unit, line unit, and transparent data transmission unit. The port impedance is 75 ohms.2xSTM-1/4 optical ports 21xE1 electrical ports8xFE electrical portsSlot 2

TNH1ISUDIntegrates the system control unit, cross-connect unit, timing unit, line unit, and tributary unit. The port impedance is 75 ohms.2xSTM-1/4 optical ports 21xE1 electrical portsSlot 2

TNH1ISUEIntegrates the system control unit, cross-connect unit, timing unit, line unit, and tributary unit. The port impedance is 120 ohms, and air cooling design is used.2xSTM-1/4 optical ports21xE1/T1 electrical ports

8xFE electrical portsThis board is used only in Vietnam.Slot 2

Extended boardsTNH1SL1D, TNH2SL1D2xSTM-1 optical interface board2xSTM-1 optical portsSlots 34

TNH1PL3T, TNH2PL3T3xE3/T3 electrical interface board3xE3/T3 electrical portsSlots 34

TNH1SP3D, TNH2SP3D42xE1 electrical interface board42xE1 electrical ports42xT1 electrical portsSlots 34

TNH1EGT1, TNH2EGT11xGE Ethernet transparent transmission board1xGE electrical portSlots 34

TNH1EFS8, TNH2EFS88xFE Ethernet switching and processing board8xFE electrical portsSlots 34

Boards Supported by V100R005 and above

System control, switching, and timing boardCSHDPacket system control, switching, and timing board4xFE electrical ports2xGE optical/electrical ports16xE1 ports (75-ohm/120-ohm)GE optical/electrical ports are equipped with the following modules:1000Base-LX1000Base-VX1000Base-ZX10/100/1000BASE-T(X)Slot 2

Packet interface boardMD132xSmart E1 service processing board32xE1 ports (75-ohm/120-ohm)Slots 34

Packet processing boardEM6TFE/GE interface board (6xRJ45)4xFE electrical ports: 10/100BASE-T(X)2xGE electrical ports (compatible with FE electrical ports): 10/100/1000BASE-T(X)Slots 34

EM6FFE/GE interface board (4xRJ45 + 2xSFP)4xFE electrical ports: 10/100BASE-T(X)

Two ports provided by SFP modules of the following types:

1000Base-LX

1000Base-VX

1000Base-ZXSlots 34

EF8F8-Port SFP Fast Ethernet Interface Board8xFE SFP(V100R006C01 and above support)Slots 34

Power boardPIUPower board.Provides 48 V/60 V DC power supply ports.Slot 5

Fan boardFANFan boardCools the chassis.Slot 6

1.2.3 Service Types

The OptiX OSN 500 supports various services, and provides a wide range of functions and features to ensure the quality and efficiency of service transmission. The OptiX OSN 500 V100R002C01 supports only TDM services, and the OptiX OSN 500 V100R005 supports only packet services. OptiX OSN 500 V100R006 added Tp-Assist and MPLS_TP features base on V100R005.The OptiX OSN 500 V100R002C01 receives/transmits the following types of TDM services: SDH services PDH services Ethernet (COS) servicesThe OptiX OSN 500 V100R005 and later receives/transmits the following types of packet services: CES services TDM E1 services Ethernet (packet) services1.2.4 Cross-Connect Capacity

For TDM services, the OptiX OSN 500 supports 21.25 Gbit/s higher order full cross-connections or 5 Gbit/s lower order full cross-connections.For packet services, the OptiX OSN 500 supports 7.2 Gbit/s cross-connections.1.2.5 Maximum Number of Received Services

The OptiX OSN 500 receives/transmits services through multiple types of ports.Table 1-1 Maximum number of received services-Service TypeService DescriptionMaximum Number of Received ServicesConnector

TDM serviceSDH serviceSTM-4 standard service2xSTM-4LC/PC

STM-1 standard service6xSTM-1LC/PC

PDH serviceE3/T3 service (75-ohm)6xE3/T3Anea 96

E1 service (75-ohm or 120-ohm) or T1 service (100-ohm)105xE1/T1Anea 96

Ethernet (EoS) serviceFast Ethernet (FE) service24xFERJ45

Gigabit Ethernet (GE) service2xGELC

Packet servicesEthernet (packet) serviceFast Ethernet (FE) service22xFERJ45

Gigabit Ethernet (GE) service6xGELC

Gigabit Ethernet (GE) service6xGERJ45

CES/ATM/IMA serviceCES/ATM/IMA service over 75-ohm or 120-ohm Smart E1 ports80xE1Anea 96

1.3 Product Portfolio

Part number: 01030124

Description OptiX OSN 500 Ultra Compact STM-1/STM-4 Compatible Optical Transmission EquipmentPart NumberDescriptionTemplatePricing / Configuring PartRemarks

01030124OptiX OSN 500 Ultra Compact STM-1/STM-4 Compatible Optical Transmission EquipmentPTOMiddle layer, level 1 part number, covering all materials for the OptiX OSN 500

02000648OptiX OSN 500 Ultra Compact STM-1/STM-4 Compatible Optical Transmission EquipmentATOMiddle layerMiddle layer, covering cabinets, subracks, boards, NE software, and accessories for equipment commissioning

02230CVFOSN 500,Auxiliary EquipmentPOCMiddle layerMiddle layer, covering accessories, such as UPMs, cabinets, and subracks

04000434OptiX OSN 500,External Cable SuitePOCMiddle layerMiddle layer, covering power supply cables and relay power supply cables

04100133OptiX OSN 500,Optical Fiber CablePOCMiddle layerMiddle layer, covering fiber jumpers, optical attenuators, fiber adapters, and dispersion compensation fibers

02237602OptiX OSN 500,Delivery AccessoriesPOCMiddle layerMiddle layer, covering accessories, documentation, cable labels, and network cables

02237603OptiX OSN 500,Suite Of Installation PartsPOCMiddle layerMiddle layer, covering cabinet doors, marking template, and mounting brackets, non-quoted item

30000109Product Complete-set Packaging OptiX OSN 500POCMiddle layerMiddle layer, covering cabinet wrapping materials, subrack wrapping materials, and board wrapping materials, which are used during the equipment hardware packing process

02239094OptiX OSN 500,Software FeePOCMiddle layerMiddle layer, covering NE software and software upgrades, quoted item

80010249OptiX OSN 500,License of Integrated STM-1/STM-4 Compatible Optical Transmission EquipmentPOCMiddle layerMiddle layer, covering license files

Description:

The product is not strictly controlled. Because there are small quantities of the America component that is below 10 percent, it can be export to the embargo country.2 NE Software Configurations2.1 Typical Configurations

A typical configuration is recommended for its short delivery period. The following typical configuration, however, is applicable only to the OptiX OSN 500 V100R002C01.Table 2-1 Typical configuration of the OptiX OSN 500 V100R002C01Part NumberDescriptionTemplatePricing / Configuring PartRemarks

02310GEKOptiX OSN 500,TNHMMODELC02,8xFE/21xE1/75ohm/2xSTM-4(S-4.1) Optical Transmission Module(220VAC) with System Control Unit Integrated with Optical and Electrical Interfaces,Accessories 4*(FC-LC,10m)/1*75ohm(10m)/Twisted-Pair Cable(30m)Delivered in one case, this item includes one 220 V chassis, one ISU board whose part number is 03052225, optical fibers, E1 cables, and network cables.Pricing part This item is applicable to an enterprise network in the Chinese market, and is configured on the Bill of Configuration pane of the Unistar CFG. No other auxiliary materials are required.

02310GEJOptiX OSN 500,TNHMMODELF02,8xFE/21xE1/75ohm/2xSTM-1(S-1.1) Optical Transmission Module(220VAC) with System Control Unit Integrated with Optical and Electrical Interfaces,Accessories 4*(FC-LC,10m)/1*75ohm(10m)/Twisted-Pair Cable(30m)Delivered in one case, this item includes one 220 V chassis, one ISU board whose part number is 03052113, optical fibers, E1 cables, and network cables.Pricing partThis item is sold only to the Chinese market, and configured based on the typical configuration. No other auxiliary materials are required.

02310GEHOptiX OSN 500,TNHMMODELE02,8xFE/21xE1/75ohm/2xSTM-4(S-4.1) Optical Transmission Module(-48VDC) with System Control Unit Integrated with Optical and Electrical Interfaces,Accessories 4*(FC-LC,10m)/1*75ohm(10m)/Twisted-Pair Cable(30m)Delivered in one case, this item includes one 48 V chassis, one ISU board whose part number is 03052225, optical fibers, E1 cables, and network cables.Pricing partThis item is sold only to the Chinese market, and configured based on the typical configuration. No other auxiliary materials are required.

02310GEGOptiX OSN 500,TNHMMODELD02,21xE1/75ohm/2xSTM-1(S-1.1) Optical Transmission Module(220VAC) with System Control Unit Integrated with Optical and Electrical Interfaces,Accessories 4*(FC-LC,10m)/1*75ohm(10m)Delivered in one case, this item includes one 220 V chassis, one ISU board whose part number is 03052119, optical fibers, E1 cables, and network cables.Pricing partThis item is applicable to an enterprise network in the Chinese market, and is configured on the Bill of Configuration pane of the Unistar CFG. No other auxiliary materials are required.

02310GEFOptiX OSN 500,TNHMMODELA02,8xFE/21xE1/75ohm/2xSTM-1(S-1.1) Optical Transmission Module(-48VDC) with System Control Unit Integrated with Optical and Electrical Interfaces,Accessories 4*(FC-LC,10m)/1*75ohm(10m)/Twisted-Pair Cable(30m)Delivered in one case, this item includes one 48 V chassis, one ISU board whose part number is 03052113, optical fibers, E1 cables, and network cables.Pricing part This item is applicable to an enterprise network in the Chinese market, and is configured on the Bill of Configuration pane of the Unistar CFG. No other auxiliary materials are required.

02310GEEOptiX OSN 500,TNHMMODELB02,21xE1/75ohm/2xSTM-1(S-1.1) Optical Transmission Module(-48VDC) with System Control Unit Integrated with Optical and Electrical Interfaces,Accessories 4*(FC-LC,10m)/1*75ohm(10m)Delivered in one case, this item includes one 48 V chassis, one ISU board whose part number is 03052119, optical fibers, E1 cables, and network cables.Pricing part This item is applicable to an enterprise network in the Chinese market, and is configured on the Bill of Configuration pane of the Unistar CFG. No other auxiliary materials are required.

02310EAROptiX OSN 500,TNHMMODELL01,8xFE(L2)/21xE1/120ohm(T1/100ohm)/2xSTM-1(S-1.1) Optical Transmission Module(-48VDC) with System Control Unit Integrated with Optical and Electrical InterfacesThis item is a typical configuration and includes one 48 V assembly chassis, one ISU board whose part number is 03052117, and one EFS8 board.Pricing partThis item is sold only to the Indian market, and is configured on the Bill of Configuration pane of the Unistar CFG. One 120-ohm E1 cable, four optical fibers, and one 80-meter network cable are quoted.

02310EAQOptiX OSN 500,TNHMMODELL02,8xFE(L2)/21xE1/120ohm(T1/100ohm)/2xSTM-4(S-4.1)/2xSTM-1(S-1.1) Optical Transmission Module(-48VDC) with System Control Unit Integrated with Optical and Electrical InterfacesThis item is a typical configuration and includes one 48 V assembly chassis, one ISU board whose part number is 03052121, one EFS8 board, and one SL1D board.Pricing partThis item is sold only to the Indian market, and is configured on the Bill of Configuration pane of the Unistar CFG. One 120-ohm E1 cable, eight optical fibers, and one 80-meter network cable are quoted.

2.2 Chassis

Part NumberDescriptionRemarksPricing/Configuring PartConfiguration Principle

02112781OptiX OSN 500,TNHB1CASE,Assembly Chassis(-48V)48 V natural heat dissipation chassisPricing partOptional for the 48 V natural heat dissipation design, but not applicable to the OptiX OSN 500 V100R005 and later.

02113095OptiX OSN 500,TNHB2CASE,Assembly Chassis(220V)220 V chassisPricing partOptional for the 220V natural heat dissipation design, but not applicable to the OptiX OSN 500 V100R005 and later.

02113233OptiX OSN 500,TNHB3CASE,Assembly Chassis,-48V,FAN48 V air cooling chassisPricing partOptional for the 48 V air cooling design, sold under control if it is used on the OptiX OSN 500 V100R002 but applicable globally if it is used on the OptiX OSN 500 V100R005 and later.

Configuration PrinciplesThe chassis is selected based on requirements for power supply systems and heat dissipation.When quoting V1R2, select typical configurations with preference.The OptiX OSN 500 V100R005 and later supports only air cooling chassis with a part number of 02113233.

Adhere to the following configuration principles:

Configure one power supply for an AC chassis, and two for a DC chassis.Configure a left angle and female power cable for an AC chassis. Do not configure a C13 straight power cable .Configure the following for each chassis: Configure one blue and one black power cable (by default, 20 m long for each) and one DC terminal for each 48/60 V DC chassis. Configure one power cable for each 110/220 V AC chassis (by default, 3 m long for each) Configure one ground cable for each chassis. The 2-m ground cable is concluded in the auxilliary material package. Integrated System Unit

2.2.2 ISU

The ISU board is applicable to the OptiX OSN 500 V100R002 only.Part NumberDescriptionRemarksPricing/Configuring PartConfiguration Principle

03052111OptiX OSN 500,TNH1ISUA01,8xFE/21xE1/120ohm(T1/100ohm)/2xSTM-1(S-1.1,LC)Integrated System Control Unit-ESFP Optical Module STM-1 120 ohms 2 km to 15 kmPricing partThis board can be used only in a natural heat dissipation chassis. Select an appropriate board based on the valid slot.

03052113OptiX OSN 500,TNH1ISUC01,8xFE/21xE1/75ohm/2xSTM-1(S-1.1,LC)Integrated System Control Unit-ESFP Optical Module STM-1 75 ohms 2 km to 15 kmPricing part

03052112OptiX OSN 500,TNH1ISUA02,8xFE/21xE1/120ohm(T1/100ohm)/2xSTM-1(L-1.1,LC)Integrated System Control Unit-ESFP Optical Module STM-1 120 ohms 15 km to 40 kmPricing part

03052114OptiX OSN 500,TNH1ISUC02,8xFE/21xE1/75ohm/2xSTM-1(L-1.1,LC)Integrated System Control Unit-ESFP Optical Module STM-1 75 ohms 15 km to 40 kmPricing part

03052115OptiX OSN 500,TNH1ISUA03,8xFE/21xE1/120ohm(T1/100ohm)/2xSTM-4(S-4.1,LC)Integrated System Control Unit-ESFP Optical Module STM-4 120 ohms 2 km to 15 kmPricing part

03052225OptiX OSN 500,TNH1ISUC03,8xFE/21xE1/75ohm/2xSTM-4(S-4.1,LC)Integrated System Control Unit-ESFP Optical Module STM-4 75 ohms 2 km to 15 kmPricing part

03052116OptiX OSN 500,TNH1ISUA04,8xFE/21xE1/120ohm(T1/100ohm)/2xSTM-4(L-4.1,LC)Integrated System Control Unit-ESFP Optical Module STM-4 120 ohms 15 km to 40 kmPricing part

03052226OptiX OSN 500,TNH1ISUC04,8xFE/21xE1/75ohm/2xSTM-4(L-4.1,LC)Integrated System Control Unit-ESFP Optical Module STM-4 75 ohms 15 km to 40 kmPricing part

03052117OptiX OSN 500,TNH1ISUB01,21xE1/120ohm(T1/100ohm)/2xSTM-1(S-1.1,LC)Integrated System Control Unit-ESFP Optical Module STM-1 120 ohms 2 km to 15 kmPricing part

03052119OptiX OSN 500,TNH1ISUD01,21xE1/75ohm/2xSTM-1(S-1.1,LC)Integrated System Control Unit-ESFP Optical Module STM-1 75 ohms 2 km to 15 kmPricing part

03052118OptiX OSN 500,TNH1ISUB02,21xE1/120ohm(T1/100ohm)/2xSTM-1(L-1.1,LC)Integrated System Control Unit-ESFP Optical Module STM-1 120 ohms 15 km to 40 kmPricing part

03052120OptiX OSN 500,TNH1ISUD02,21xE1/75ohm/2xSTM-1(L-1.1,LC)Integrated System Control Unit-ESFP Optical Module STM-1 75 ohms 15 km to 40 kmPricing part

03052121OptiX OSN 500,TNH1ISUB03,21xE1/120ohm(T1/100ohm)/2xSTM-4(S-4.1,LC)Integrated System Control Unit-ESFP Optical Module STM-4 120 ohms 2 km to 15 kmPricing part

03052227OptiX OSN 500,TNH1ISUD03,21xE1/75ohm/2xSTM-4(S-4.1,LC)Integrated System Control Unit-ESFP Optical Module STM-4 75 ohms 2 km to 15 kmPricing part

03052122OptiX OSN 500,TNH1ISUB04,21xE1/120ohm(T1/100ohm)/2xSTM-4(L-4.1,LC)Integrated System Control Unit-ESFP Optical Module STM-4 120 ohms 15 km to 40 kmPricing part

03052228OptiX OSN 500,TNH1ISUD04,21xE1/75ohm/2xSTM-4(L-4.1,LC)Integrated System Control Unit-ESFP Optical Module STM-4 75 ohms 15 km to 40 kmPricing part

03053313OptiX OSN 500,TNH1ISUE01,8xFE/21xE1/120ohm(T1/100ohm)/2xSTM-1(S-1.1,LC)Integrated System Control Unit-ESFP Optical Module-FAN STM-1 120 ohms 2 km to 15 kmPricing partThis board can be used only in an air cooling chassis and is sold under control. Select an appropriate board based on the valid slot.

03053376OptiX OSN 500,TNH1ISUE03,8xFE/21xE1/120ohm(T1/100ohm)/2xSTM-1(L-1.1,LC)Integrated System Control Unit-ESFP Optical Module-FAN STM-1 120 ohms 15 km to 40 kmPricing part

03053320OptiX OSN 500,TNH1ISUE02,8xFE/21xE1/120ohm(T1/100ohm)/2xSTM-4(S-4.1,LC)Integrated System Control Unit-ESFP Optical Module-FAN STM-4

120 ohms

2 km to 15 kmPricing part

03053377OptiX OSN 500,TNH1ISUE04,8xFE/21xE1/120ohm(T1/100ohm)/2xSTM-4(L-4.1,LC)Integrated System Control Unit-ESFP Optical Module-FAN STM-4 120 ohms 15 km to 40 kmPricing part

03053810OptiX OSN 500,TNH1ISUF03,21xE1/120ohm(T1/100ohm)/2xSTM-4(S-4.1,LC)Integrated System Control Unit-ESFP Optical Module-FANSTM-4120ohm 2~20KMPricing part

03053811OptiX OSN 500,TNH1ISUF01,21xE1/120ohm(T1/100ohm)/2xSTM-1(S-1.1,LC)Integrated System Control Unit-ESFP Optical Module-FANSTM-1120ohm 2~20KMPricing part

03053812OptiX OSN 500,TNH1ISUF02,21xE1/120ohm(T1/100ohm)/2xSTM-1(L-1.1,LC)Integrated System Control Unit-ESFP Optical Module-FANSTM-1120ohm 20~60KMPricing part

03053813OptiX OSN 500,TNH1ISUF04,21xE1/120ohm(T1/100ohm)/2xSTM-4(L-4.1,LC)Integrated System Control Unit-ESFP Optical Module-FANSTM-4120ohm 20~60KMPricing part

02310GKEOptiX OSN 500,TNH1ISUA05,8xFE/21xE1/120ohm(T1/100ohm)/2xSTM-1Integrated System Control UnitThe part number of its finished board is 03030NSP.The part number of the STM-1 module collection is 02230GDV.Pricing partThese items are quoted independently. If TDM optical ports are quoted independently, quote the combination of finished board and optical module.

02310GKGOptiX OSN 500,TNH1ISUA06,8xFE/21xE1/120ohm(T1/100ohm)/2xSTM-4ntegrated System Control UnitThe part number of its finished board is 03030NSQ.The part number of of the STM-4 module collection is 02230GDW.Pricing part

02310GKKOptiX OSN 500,TNH1ISUB05,21xE1/120ohm(T1/100ohm)/2xSTM-1Integrated System Control UnitThe part number of its finished board is 03030NST.The part number of the STM-1 module collection is 03030NST.Pricing part

02310GKMOptiX OSN 500,TNH1ISUB06,21xE1/120ohm(T1/100ohm)/2xSTM-4Integrated System Control UnitThe part number of its finished board is 03030NSU.The part number of the STM-1 module collection is 02230GDW.Pricing part

02310GKFOptiX OSN 500,TNH1ISUC05,8xFE/21xE1/75ohm/2xSTM-1 Integrated System Control UnitThe part number of its finished board is 03030NSR.The part number of the STM-1 module collection is 02230GDV.Pricing part

02310GKHOptiX OSN 500,TNH1ISUC06,8xFE/21xE1/75ohm/2xSTM-4 Integrated System Control UnitThe part number of its finished board is 03030NSS.The part number of the STM-1 module collection is 02230GDW.Pricing part

02310GKLOptiX OSN 500,TNH1ISUD05,21xE1/75ohm/2xSTM-1Integrated System Control UnitThe part number of its finished board is 03030NSV.The part number of the STM-1 module collection is 02230GDV.Pricing part

02310GKNOptiX OSN 500,TNH1ISUD06,21xE1/75ohm/2xSTM-4Integrated System Control UnitThe part number of its finished board is 03030NSW.The part number of the STM-1 module collection is 02230GDW.Pricing part

02310GKQOptiX OSN 500,TNH1ISUE05,8xFE/21xE1/120ohm(T1/100ohm)/2xSTM-1Integrated System Control Unit-FANThe part number of its finished board is 03030NSX.The part number of the STM-1 module collection is 02230GDV.Pricing part

02310GKROptiX OSN 500,TNH1ISUE06,8xFE/21xE1/120ohm(T1/100ohm)/2xSTM-4Integrated System Control Unit-FANThe part number of its finished board is 03030NSY.The part number of the STM-4 module collection is 02230GDW.Pricing part

02310GQROptiX OSN 500,TNH1ISUF05,21xE1/120ohm(T1/100ohm)/2xSTM-1Integrated System Control Unit-FANThe part number of its finished board is 03030NTH.The part number of the STM-1 module collection is 02230GDV.Pricing part

02310GQTOptiX OSN 500,TNH1ISUF06,21xE1/120ohm(T1/100ohm)/2xSTM-4Integrated System Control Unit-FANThe part number of its finished board is 03030NTJ.The part number of the STM-4 module collection is 02230GDW.Pricing part

FeaturesThe ISU board provides: System control & communication (SCC) Cross-connect (XC) Synchronous timing generator (STG) 2 x STM-1 or 2 x STM-4 lines 8 x FE 10M/100M Ethernet 21 x E1 tributary unitOptical port type: LCSlot ID: ISUConfiguration PrincipleOne ISU board is required for a chassis, and detailed specifications are case-specific.An ISU board may require the following cables: One 75-ohm/120-ohm 21 x E1 cable (functioning as an E1/T1 cable when the port impedance is 120 ohms) Four single-mode LC optical fibers One clock cable. If a 120-ohm cable is required, prepare cables whose part numbers are 25050014 and 14080082 on site. If a 75-ohm cable is required, deliver the cable whose part number is 04044726. One F2 serial port cable assembled on site (part number: 25050014 + 14080082)

One alarm input/output cable assembled on site (part number: 25050014 + 14080082)

One NMS cable assembled on site (part number: 25050014 + 14080082)

Eight crossover cables assembled on site (part number: 25050014 + 14080082)2.2.3 CSHD

The CSHD board is applicable to the OptiX OSN 500 V100R005 and later.Part NumberDescriptionRemarksPricing/Configuring PartConfiguration Principle

02310BQXOptiX OSN 500,TNH1PCSB,2*GE(SFP),Packet Cross-connect Switch Board,1*1Configurable boardPricing partQuote this part as required.

03020YQUOptiX OSN 500,TNH1CSHDA,16*E1(CES)(75ohm)/2*GE(SFP)/4*FE(RJ45),Hybrid/Packet System Control and Cross-connect Switch Board,1*1 75 ohms 16xE1, 2xGE, or 4xFEPricing partThis board is used only in an air cooling chassis.

03020YQVOptiX OSN 500,TNH1CSHDB,16*E1(CES)(120ohm)/2*GE(SFP)/4*FE(RJ45),Hybrid/Packet System Control and Cross-connect Switch Board,1*1 120 ohms 16xE1, 2xGE, or 4xFEPricing partThis board is used only in an air cooling chassis.

02230CNNOptiX OSN 500,GE SFP Module Collection(Commerce Level)Middle layer

34060473Optical transceiver,eSFP,1310nm,1.25Gb/s,-9~-3dBm,-20dBm,LC,Single Mode,10km 1310 nm 10 km

LCPricing part

34060298Optical Transceiver,eSFP,1310nm,1.25Gb/s,-5~0dBm,-23dBm,LC,SM,40km 1310nm 40 km

LCPricing part

34060360Optical Transceiver,eSFP,1550nm,1.25Gb/s,-2~5dBm,-23dBm,LC,SM,80km 1550 nm 80 km

LCPricing part

34060470Optical Transceiver,ESFP,Tx1310/Rx1490,1.25Gb/s,-3dBm,-9dBm,-19.5dBm,LC,Single Mode,10km Single-fiber bidirectional Tx1310/Rx1490 10 km LCPricing part

34060475Optical Transceiver,ESFP,Tx1490/Rx1310,1.25Gb/s,-3dBm,-9dBm,-19.5dBm,LC,Single Mode,10km Single-fiber bidirectional Tx1490/Rx1310 10 km LCPricing part

341000521000BASE-T (RJ45) SFP Electrical Module,Auto Negotiate,100mElectrical modulePricing partOne network cable and two RJ45 connectors are delivered with this module.

FeaturesThe CSHD board supports clock synchronization at the physical layer, clock protection, ACR, and IEEE 1588v2, and provides four FE electrical ports, two GE ports (SFP), and one 16xE1 (CES/IMA/ATM) port.Optical port type: A maximum of two small form-factor pluggable (SFP) modules are supported.Slot ID: Slot 2Configuration PrinciplesOne CSHD board is required for a chassis, and detailed specifications are case-specific.A CSHD board may require the following cables: One 75-ohm/120-ohm 21 x E1 cable (functioning as an E1/T1 cable when the port impedance is 120 ohms) Single-mode LC optical fibers (two fibers for an optical module, and one fiber for an optical module for the single-fiber bidirectional scenario) One clock cable. If a 120-ohm cable is required, prepare cables whose part numbers are 25050014 and 14080082 on site. If a 75-ohm cable is required, deliver the cable whose part number is 04044726. One alarm input/output cable assembled on site (part number: 25050014 + 14080082)

One NMS cable assembled on site (part number: 25050014 + 14080082)

Four crossover cables assembled on site (part number: 25050014 + 14080082)2.3 Interface Boards

2.3.1 SL1D

The SL1D is a 2xSTM-1 optical interface board. This board is applicable to the OptiX OSN 500 V100R002 only.Part NumberDescriptionFeaturePricing/Configuring PartConfiguration Principle

03053397OptiX OSN 500,TNH2SL1D03,2xSTM-1(L-1.2,LC) Optical Interface Board-ESFP Optical Module 2xSTM-1 ports L-1.2, LCPricing partThe TNH2SL1D board can substitute for the TNH1SL1D. Four single-moded LC optical fibers are quoted.These items are quoted independently. If TDM optical ports are quoted independently, quote the combination of finished board and optical module.

03053613OptiX OSN 500,TNH2SL1D01,2xSTM-1(S-1.1,LC)Optical Interface Board-ESFP Optical Module 2xSTM-1 ports S-1.1, LCPricing part

03053614OptiX OSN 500,TNH2SL1D02,2xSTM-1(L-1.1,LC)Optical Interface Board,ESFP Optical Module 2xSTM-1 ports L-1.1, LCPricing part

03053652OptiX OSN 500,TNH2SL1D04,2xSTM-1Optical Interface Board(S-1.1,LC,Single Fibre Bidirectional,1550nm at TX1 & 1310nm at TX2) 2xSTM-1 ports S-1. 1, LC Single-fiber bidirectionalPricing part

03053653OptiX OSN 500,TNH2SL1D05,2xSTM-1Optical Interface Board(L-1.1,LC,Single Fibre Bidirectional,1550nm at TX1 & 1310nm at TX2) 2xSTM-1 ports L-1.1, LC Single-fiber bidirectionalPricing part

02310CNNOptiX OSN 500,TNH2SL1D,2xSTM-1Optical Interface BoardThe part number of the finished board is 03020YFB. The part number of the STM-1 optical module collection is 02230DLP.Pricing part

FeaturesThe SL1D board is used to receive and transmit 2xSTM-1 optical signals, to perform O/E conversion for the STM-1 optical signals, to extract or insert overhead bytes, and to report alarms generated on the line.This board provides 2xSTM-1 optical ports.Slot ID: Slot 3 or slot 4Configuration PrinciplesConfigure an appropriate board based on the valid slot.Quote one board together with four single-mode LC optical fibers and two single-fiber bidirectional optical modules.2.3.2 EGT1

The EGT1 is a 1xGE transparent transmission board. This board is applicable to the OptiX OSN 500 V100R002 only.Part NumberDescriptionRemarksPricing/Configuring PartConfiguration Principle

03053619OptiX OSN 500,TNH2EGT101,1-Port Gigabit Ethernet Transparent Transmission Board(1000BASE-LX,1310-LC)1310-LCPricing partThe TNH2EGT1 board can substitute for the TNH1EGT1 board. Two single-moded LC optical fibers are quoted.

03053802OptiX OSN 500,TNH2EGT102,1-Port Gigabit Ethernet Transparent Transmission Board(1000BASE-SX,850-LC)850-LCPricing part

03053657OptiX OSN 500,TNH2EGT103,1-Port Gigabit Ethernet Transparent Transmission Board(1000BASE-LX,LC,Single Fibre Bidirectional,1310 Sending&1490 Receiving)Single-fiber bidirectional, Tx1310/Rx1490Pricing part

03053658OptiX OSN 500,TNH2EGT104,1-Port Gigabit Ethernet Transparent Transmission Board(1000BASE-LX,LC,Single Fibre Bidirectional,1490 Sending&1310 Receiving)Single-fiber bidirectional, Tx1490/Rx1310Pricing part

02310GKVOptiX OSN 500,TNH2EGT105,1-Port Gigabit Ethernet Transparent Transmission BoardThe part number of the finished board is 03021AFF. The part number of the optical module collection is 02230GDL.Pricing partThis item is quoted independently. If TDM optical ports are quoted independently, quote the combination of finished board and optical module.

FeaturesThe EGT1 board supports transparent transmission of Ethernet services, LCAS, and test frames.This board provides one GE optical port.Slot ID: Slot 3 or slot 4Configuration PrinciplesSelect an appropriate board based on the valid slot.Quote one board together with two single-mode or multi-mode LC optical fibers.2.3.3 SP3D

The SP3D is a 42xE1 electrical interface board. This board is applicable to the OptiX OSN 500 V100R002 only.Part NumberDescriptionRemarksPricing / Configuring PartConfiguration Principle

03020YSGOptiX OSN 500,TNH2SP3DA,42xE1/120ohm(T1/100ohm) Electrical Interface Board-1x1 Assembled Board42x120-ohm E1/100-ohm T1Pricing partThe TNH2 board can substitute for the TNH1 board. Two 120-ohm or 75-ohm 21xE1 power cables are quoted.

03021AGUOptiX OSN 500,TNH2SP3DB,42xE1/75ohm Electrical Interface Board-1x1 Assembled Board42x75-ohm E1Pricing part

FeaturesThe SP3D processes E1 signals and overheads, and supports alarms, performance events, and maintenance features.The board provides 42xE1/T1 electrical ports.Port type: Anea 96Slot ID: Slot 3 or slot 4Configuration PrinciplesSelect an appropriate board based on the valid slot and port impedance.Quote this part together with two 120-ohm/75-ohm 21xE1 cables (functioning as an E1/T1 cable when the port impedance is 120 ohms).2.3.4 PL3T

The PL3T is a 3xE3/T3 electrical interface board. This board is applicable to the OptiX OSN 500 V100R002 only.Part NumberDescriptionRemarksPricing / Configuring PartConfiguration Principle

03020YVNOptiX OSN 500,TNH2PL3T,3*E3/T3 Electrical Interface Board,1*13x75ohm E3/T3Pricing partThe TNH2 board can substitute for the TNH1 board. Six E3/T3 power cables are quoted.

FeaturesThe PL3T board processes E3/T3 signals and overheads, and supports alarms, performance events, and maintenance features.The board provides 3xE3/T3 75-ohm electrical ports.Port type: SMBSlot ID: Slot 3 or slot 4Configuration PrinciplesConfigure an appropriate board based on the valid slot.Quote this part together with six 75-ohm trunk cables (part number: 04041166), of which one end is an SMB connector and the other end is made on site).2.3.5 EFS8

The EFS8 is an 8xFE switching and processing board. This board is applicable to the OptiX OSN 500 V100R002 only.Part NumberDescriptionRemarksPricing / Configuring PartConfiguration Principle

03020YNEOptiX OSN 500,TNH2EFS8,8-Port 100M Fast Ethernet Processing Board with LAN Switch8xFE, RJ45Pricing partThe TNH2 board can substitue for the TNH1 board. One 80-meter network cable is quoted.

FeaturesThe EFS8 board supports transparent transmission of Ethernet services, LCAS, and test frames.Port type: RJ45Slot ID: Slot 3 or slot 4Configuration PrinciplesSelect an appropriate board based on the valid slot.Quote this board together with eight 80-meter crossover cables that are assembled on site (part number: 25050014 + 14080082).

2.3.6 EM6T

This board is applicable to the OptiX OSN 500 V100R005 and later.The EM6T is an FE/GE interface board providing four FE electrical ports and two GE electrical ports.Part NumberDescriptionRemarksPricing/Configuring PartConfiguration Principle

03053488OptiX OSN 550,TNM1EM6T,4 * FE (RJ45)/2 *GE(RJ45) Fast/Gigabit Ethernet Board with switch function 4xFE (RJ45) 2xGE (RJ45)Pricing part

FeaturesThe EM6T receives/transmits, processes, and converges four FE signals and two GE signals. The EM6T works with the packet unit of the ISU board to process Ethernet services.Port type: 4xFE (RJ45) + 2xGE (RJ45)Slot ID: Slot 3 or slot 4Configuration PrinciplesConfigure an appropriate board based on the valid slot.Quote this board together with: Six 50-meter long crossover cables that are assembled on site (part number: 25050014 + 14080082)

LC optical fibers (two for each optical module)2.3.7 EM6F

This board is applicable to the OptiX OSN 500 V100R005 and later.The EM6F is an FE/GE interface board providing four FE electrical ports and two GE electrical ports. The GE ports equipped with SFP modules can be optical or electrical. The GE and FE electrical ports are compatible with each other.


02310BVAOptiX OSN 500,TNH1PCSB,SFP Board(Packet Service Board)Configurable boardPricing partQuote this part as required.

03053487OptiX OSN 550,TNM1EM6F,4 * FE (RJ45)/2 *GE(SFP) Fast/Gigabit Ethernet Board with switch function 4xFE (RJ45) 2xGE (SFP)Pricing part

02230EUAOptiX OSN 550,Optical Transceiver Assembly For TNM1PCXLG Client Side,ESFP,GEOptical moduleMiddle layer

34060473Optical transceiver,eSFP,1310nm,1.25Gb/s,-9~-3dBm,-20dBm,LC,Single Mode,10km 1310 nm 10 km

LCPricing part

34060298Optical Transceiver,eSFP,1310nm,1.25Gb/s,-5~0dBm,-23dBm,LC,SM,40km 1310 nm 40 km

LCPricing part

34060360Optical Transceiver,eSFP,1550nm,1.25Gb/s,-2~5dBm,-23dBm,LC,SM,80km 1310nm 80 km LCPricing part

34060470Optical Transceiver,ESFP,Tx1310/Rx1490,1.25Gb/s,-3dBm,-9dBm,-19.5dBm,LC,Single Mode,10km Single-fiber bidirectional Tx1310/Rx1490

10 km

LCPricing part

34060475Optical Transceiver,ESFP,Tx1490/Rx1310,1.25Gb/s,-3dBm,-9dBm,-19.5dBm,LC,Single Mode,10km Single-fiber bidirectional Tx1490/Rx1310

10 km

LCPricing part

34060286Optical Transceiver,eSFP,850nm,2.125Gb/s(Multi rate) ,-9.5~-2.5dBm,-17dBm,LC,MM,0.5km 850nm 0.5km LCPricing part

FeaturesPort type: 4xFE (RJ45) + 2xGE (RJ45)Slot ID: Slot 3 or slot 4Configuration PrinciplesConfigure an appropriate board based on the valid slot.Quote this board together with:Four 30-meter long crossover cables that are assembled on site (part number: 25050014 + 14080082)

LC optical fibers (two fibers for an optical module, and one fiber for an optical module for the single-fiber bidirectional scenario)2.3.8 MD1

The MD1 is a 32xSmart E1 service processing board. This board is applicable to the OptiX OSN 500 V100R005 and later.Part NumberDescriptionRemarksPricing/Configuring PartConfiguration Principle

03053485OptiX OSN 550,TNM1MD1A,Multi-protocol 32 Channels E1 Interface Processing Board (75ohm) 32xE1 75 ohm

03053484OptiX OSN 550,TNM1MD1B,Multi-protocol 32 Channels E1 Interface Processing Board (120ohm) 32xE1 120 ohm

FeaturesThe MD1 receives and transmits 32xE1 signals.Port type: Anea 96Slot ID: Slot 3 or slot 4Configuration PrinciplesConfigure an appropriate board based on the valid slot.Quote this board together with two 75-ohm/120-ohm 16xE1 cables.2.3.9 CQ1The CQ1 is for use with the OptiX OSN 550 V100R006C01.

The CQ1 board supports access, processing, and convergence of STM-1 signals on four ports.

Optical modules can be separately quoted or combine quoted. When separately quoted, choose the required optical modules from the appropriate optical module collections. For the part numbers of particular optical modules, see the PDM database or the configurator.Part NumberTypeDescriptionFeatureProperty

03054815TNM1CQ101Finished Board Unit,Optix OSN 550,TNM1CQ101,4*Channelized STM-1 Optical Interface Board(S-1.1,LC)4*STM-1

S-1.1Quoted item

03054812TNM1CQ102Finished Board Unit,Optix OSN 550,TNM1CQ102,4*Channelized STM-1Optical Interface Board (L-1.1,LC)4*STM-1

L-1.1Quoted item

03054814TNM1CQ103Finished Board Unit,Optix OSN 550,TNM1CQ102,4*Channelized STM-1Optical Interface Board (L-1.1,LC)4*STM-1

L-1.2Quoted item

03054809TNM1CQ104Finished Board Unit,Optix OSN 550,4*Channelized STM-1Optical Interface Board(S-1.1,LC,Single Fibre Bidirectional,1310nm at TX1 and TX2 & 1550nm at TX3 and TX4)4*STM-1

S-1.1 single Quoted item

separately quoted of the CQ1 board

02310NHNTNM1CQ1Function Module,OptiX OSN 550,TNM1CQ1,4*Channelized STM-1 Optical Interface Board4*STM-1

Base board: 03054373Quoted item

Packet optical module collections corresponding to the CQ1 boards

02230RUVSubassembly | Accessories,OptiX OSN 550,TNM1CQ1 Optical Transceiver Assembly For TNM1CQ1 Client Side,SFP,ESFP

STM-1 white-light optical module collection, covering 15km, 40km, 80km, STM-1e, single-fiber bidirectional optical modules.Middle layer

FeaturesPort type: 4*STM-1 Slot ID: slots 1 to 6Configuration Principles

Configure the quotation on the Configure Board window on the configurator.When configuring single-fiber bidirectional optical modules, ensure that the Tx and Rx wavelengths match those at the opposite end.

Configure two single-mode LC optical fibers for each ordinary optical module.

Configure one single-mode LC optical fiber for each single-fiber bidirectional optical module.2.3.10 EF8FThe EF8F is for use with the OptiX OSN 550 V100R006C01.

The EF8F board supports access, processing, and convergence of FE signals on eight ports.

Optical modules must be separately quoted. Choose the required optical modules from the appropriate optical module collections. For the part numbers of particular optical modules, see the PDM database or the configurator. FeaturesPart NumberTypeDescriptionFeatureProperty

03021BLBTNM1EF8FOptiX OSN 550, TNM1EF8F, 8-Port SFP Fast Ethernet Interface Board, 1*1Eight FE ports (SFP)

Optical modules are not included in this item.Quoted item

Packet optical module collections corresponding to the EF8F boards

02230EYJOptiX OSN 550, FE eSFP Module Collection(Industry Level)FE optical module collection (65C), covering 15-km, 40-km, and 80-km optical modules/

02230EYDOptiX OSN 550, FE eSFP Module Collection(Commerce Level)FE optical module collection (55C), covering 15-km, 40-km, and 80-km single-fiber unidirectional optical modules, and 15-km and 40-km single-fiber bidirectional optical modules/

02230FKVOptiX OSN 1800,Optical Transceiver Assembly For OSN 1800 Client Side,RJ45 FE100Base-T-SFP- RJ45 Electrical Module

FeaturesPort type: eight FE ports (eSFP) Slot ID: slots 3 to 4Configuration Principles

Configure the quotation on the Configure Board window on the configurator.When configuring single-fiber bidirectional optical modules, ensure that the Tx and Rx wavelengths match those at the opposite end.

Configure two single-mode LC optical fibers for each ordinary optical module.

Configure one single-mode LC optical fiber for each single-fiber bidirectional optical module.Configure one FE port license for each optical module.2.4 External Components

The external component of the OptiX OSN 500 is the orderwire phone. This board is applicable to the OptiX OSN 500 V100R002 only.Part NumberDescriptionRemarksPricing/Configuring PartConfiguration Principle

03020MGUOptiX OSN 500,TNH1EOW,Sub-Board of Engineering Order Wire Board-1*1-Pricing partConfigure one piece if the OptiX OSN 500 needs to provide orderwire services.

2.5 Software Package

Part NumberDescriptionRemarksPricing / Configuring PartConfiguration Principle

05019850OptiX OSN 500 V100R002C01,Software Package for OptiX OSN 500V100R002C01 software packageConfiguring partOne software package is delivered for one set of OptiX OSN 500 V100R002C01 equipment.

05010KKJOptiX OSN 500 V100R005C00,Software Package for OptiX OSN 500V100R005C00 software packageConfiguring partOne software package is delivered for one set of OptiX OSN 500 V100R005C00 equipment.

05010SHEOptiX OSN 500 V100R005C02,Software Package for OptiX OSN 500V100R005C02 software packageConfiguring partOne piece is configured if there is a master device V100R005C02.

05010WQFOptiX OSN 500 V100R006C00,Software Package for OptiX OSN 500V100R006C00 software packageConfiguring partOne piece is configured if there is a master device V100R006C00.

05011EHXOptiX OSN 500 V100R006C01,Software Package for OptiX OSN 500V100R006C01 software packageConfiguring partOne piece is configured if there is a master device V100R006C01.

05011NTJOptiX OSN 500 V100R007C00,Software Package for OptiX OSN 500V100R007C00 software packageConfiguring partOne piece is configured if there is a master device V100R007C00.

05010RSLOptiX OSN 500 V100R002C01SPC150,Software Package For OptiX OSN 500V1R2C01SPC150 software packageConfiguring part

05010RSJOptiX OSN 500 V100R002C01SPC200,Software Package For OptiX OSN 500V1R2C01SPC200 software packageConfiguring part

05010RSKOptiX OSN 500 V100R002C01SPC300,Software Package For OptiX OSN 500V1R2C01SPC300 software packageConfiguring part

05017766OptiX OSN 500,TNHISU00,Simulation Package,ProgramPrograms loaded during manufacturingConfiguring partBy default, this item is not configured.

2.6 Commissioning Accessories


2906061328-5043-900238,20mm*40mm,2012-1-15,SDH-based Multiservice Transport Platform (MSTP) Equipment,OptiX OSN 500Network entrance certificateDelivered in bulksOne piece must be configured for each set of equipment.

31092502OptiX OSN 500 STM-1/STM-4 Multi-Service CPE Optical Transmission System Factory Acceptance Report-(V100R002_02)Factory acceptance reportConfiguring partOne for a contract, not provided by default. Provided in the following conditions:The CPP specifies "Please provide the factory acceptance report."

31092573OptiX OSN 500 Multi-Service CPE Optical Transmission System Factory Acceptance Report-(V100R005_02)Factory acceptance reportConfiguring part

21135448DKBA4.130.7423MX,blank panel,193.8mm*20.32mm*23.2mm,sheetmetalFiller panelDelivered in bulksConfigure this item based on actual situations. If required, this item is used in slot 3 or 4.

21135764Front Panel, DKBA4.130.7801MX, Blank Panel, 193.8mm*22.86mm*23.5mm, SheetmetalFiller panelDelivered in bulks

29042301DKBA.8.817.6637,China RoHS -50 Year Label 2,common,46mm*34mm,PET,SilverRoHS labelDelivered in bulksThis item is not used by default.

29041013DKBA8.817.1759,Product Blank Nameplate,ViewPoint Production,70X46,3M7818Blank qualification cardDelivered in bulks

29041692DKBA8.817.3829,RoHS Label,Common Label,34*46mm,3M7818/Fasson 72826/BRADY B435RoHS labelDelivered in bulksThis item is not used by default.

29100019Label-Blank label-5 columns-12.0mm*4.0mm-DKBA8.818.1595-PET-silverBlank label Delivered in bulksThis item is printed on site.

63200084DKBA8.034.0704,Dust-proof Cushion,Metro 3600Dust-proof cushionDelivered in bulksConfigure one item for an optical port if the optical port vacant.

3 Auxiliary Materials3.1 Cabinet Suite


02238800OptiX Metro 1000,Package of N63 Rack and Rack Installation SuiteN63E cabinetMiddle layer

02113061OptiX Metro 1000,SS4B1RACK01,N63E Assemble Rack(2200x600x300mm)(322)N63EETSI assembled cabinet, 2.2 m high and 300 mm deep, without a PDUPricing partQuote this item as required.

02113062OptiX Metro 1000,SS4B1RACK02,N63E Assemble Rack(2000x600x300mm)(320)N63EETSI assembled cabinet, 2.0 m high and 300 mm deep, without a PDUPricing partQuote this item as required. Generally, the OptiX OSN 500 does not use this type of cabinet.

02237873OptiX,300mm Deep Assembled Rack Installation Suite(for N63E)Auxiliary equipment for the N63E cabinetMiddle layer

21050278DKBA4.120.1147MX,Front Door,N63B-22 Cabinet,594X24.5X2072Front door of the 2.2 m high cabinetdelivered in bulksOne piece is required for a cabinet with a height of 2.2 m and a depth of 0.3 m.

21050280DKBA4.120.1157MX,Front Door,N63E-20 Cabinet,594X24.5X1872Front door of the 2.0 m high cabinetdelivered in bulksOne piece is required for a cabinet with a height of 2.0 m and a depth of 0.3 m.

21150584DKBA4.070.0722MX,N6X Concrete Floor Mount Kit,For Mount in Concrete Floor,Concrete Floor Mount structureDevices for installing the N6X cabinet on the concrete floorConfiguring partOne piece for a cabinet that is installed on the concrete floor

21101194Q/DKBA8.088.0709,Installation Marking Template,Transmission Cabinet (Depth 300mm)Device for making marks on the concrete floorConfiguring partOne piece for a cabinet that is installed on the concrete floor

21150582DKBA4.070.0840MX,N63 Unitary Support Mount Kit I(Adjustable Height 296~465mm),For mounting on antistatic floor,SupportDevices for supporting cabinets that are installed on the ESD floor, with an adjustable height ranging from 296 mm to 465 mmConfiguring partSelect an appropriate type of supports based on height of the ESD floor, and deliver two supports for each cabinet.

21150583DKBA4.070.0871MX,N63 Unitary Support Mount Kit II,Height Tailor-Made(The lowest height is 150mm,The highest height is 700mm),For mounting on antistatic floor,Support

Devices for supporting cabinets that are installed on the ESD floor, with a fixed height equal to or higher than 150 mmConfiguring part

21150599DKBA4.070.0877,N63 Unitary Cabinet Installation Drawing Template(Antistatic Floor),N63 Cabinet,Drawing TemplateDevice for making marks on the ESD floorConfiguring partOne piece for a cabinet that is installed on the ESD floor. This item is not delivered by default.

21150572DKBA4.070.0670MX,Top Fixing Mount Kit (Adjustable Height: 175mm~225mm), For the top of cabinet fixed,Engineer Installation StructureDevices for fastening cabinet top to the overhead cable traysConfiguring partDeliver N + 1 pieces for a row of N cabinets. This item is not delivered by default.

21070321DKBA4.133.0380MX,Frame(400),N63E/N63B Cabinet,600*300*400This item and a 2.2 m high cabinet form a 2.6 m high cabinet.Pricing partOne piece is required to provide a cabinet with a height of 2.6 m and a depth of 0.3 m.

21150259Q/DKBA4.070.0236MX,Rack Shockproof Reinforcement Components,All RacksDevice for reinforcing the equipment Configuring partConfigure one piece for one cabinet. This item is not delivered by default.

29042338DKBA4.150.0901MX,LOGO Plate(for HUAWEI LOGO),GM_Cabinet_N66,PlasticLogo plate for the N66 cabinetDelivered in bulksOne piece is affixed to the cabinet door with a part number of 21050278 or 21050280 before delivery.

29042495DKBA4.150.0962MX,LOGO Plate (For OptiX LOGO),N63B Cabinet,90*30,PlasticLogo plate for the N63 cabinetDelivered in bulks

02234590OptiX Metro 1000,Suite Of Installation Parts(19 Inch Open Rack Slide Mount Kit-For rack)Middle layer

21020281DKBA4.102.0422MX,19" Open rack 2.0m,General,rack19-inch open rack with a height of 2.0 mPricing partQuote this item as required.

21020280DKBA4.102.0389MX,19" Open rack 2.2m,General,rack19-inch open rack with a height of 2.2 mPricing partQuote this item as required.

21150505DKBA4.150.0653MX,19" Open Rack Mount Kit in Concrete Floor,Low CostDevices for installing the 19-inch open rack on the concrete floorConfiguring partOne piece for a rack that is installed on the concrete floor

21101266DKBA8.088.1313,Installation Marking Template,19inch Open Rack(For Raised Floor Installation)Device for making marks on the ESD floorConfiguring partOne piece for a rack that is installed on the ESD floor. This item is not delivered by default.

02238798OptiX Metro 1000, 16 mm^2 Open Rack Earthing cable SetEarthing components for 19-inch open racksSuiteConfigure one piece for each 19-inch open rack.

21150579DKBA4.070.0725MX,BTS Unitary Support Mount Kit I(Adjustable Height 296~465mm) ,For mounting on antistatic floor,SupportSupport for installing racks on the ESD floorEngineering survey itemConfigure two piece for each rack to be installed on the ESD floor. This item is not delivered by default.

21150580DKBA4.070.0726MX,BTS Unitary Support Mount Kit II,Height Tailor-Made(The lowest height is 150mm,The highest height is 700mm),For mounting on antistatic floor,Support

Engineering survey item

02239166PDU/PDU Power Cable and Crimping AccessoryPDU suiteMiddle layer

02120242OptiX Metro1000,SS44PDU,Power Distribution UnitDC power distribution unitPricing partConfigure one piece of each N63E cabinet.

3.2 Orderwire Phone


02160177HUAWEI EchoLife IP Phone ET525, IP Terminal phone,Chinese&English documents,adapter should be satisfied with Chinese standardOrderwire phonePricing partIf required, quote one orderwire phone for local orderwire services, and one orderwire phone plus one set of extended orderwire phone accessories for extended orderwire services. These items are not supported by the OptiX OSN 500 V100R005.

02233530OptiX 2500+,Extend Telephone AccessoriesExtended orderwire phone accessoriesConfiguring part

3.3 Batteries

The batteries include UPMs and accessories. The OptiX OSN 500 has a UPM power system.


02290047UPS,1kVA,1h,220V, Single In Single Out,50Hz, Battery Out of Cupboard,Pantone Gray 3COne-in and one-out intelligent UPS productPricing partQuote this item manually if it is required.

02130571AC/DC--25degC-65degC-85V-285V-5VDC/8A,-48V/0.2APower supply for an integrated chassisPricing partQuote this item manually if it is required.

02230CUASubassembly | Accessories,OSN 500,UPM & AccessoriesUPM accessoriesPricing partQuote this item if the UPM is required.

02239182OptiX Metro 1000,Rechargeable Battery AccessoriesRechargeable Battery Accessories and AccessoriesPricing partQuote this item if the Rechargeable Battery is required. Recommended use 220 V chassis to replace this item.

3.4 Installation Tools


02210181Tools-Installation Kit of SDH (20 pcs)/ With Configuration List/Russia type plugTools such as wire stripper, COAX crimping tools, screwdrivers, cutter, soldering iron, measuring tape, and tweezersPricing partQuote this item (used in Russia only) manually.

02210187Tools-installation Kit Of SDH(Without Power Tools),Chinese&English Documents,With Configuration TablePricing partQuote this item manually.

05040500Vertel OSI Stack,English Version,No Doc.,with ETS-LAN stack & DCC stack & IS-IS stackTP4 software licensePricing partManually quote one piece for each set of equipment if it is required.

28050001Wrist StrapWrist StrapPricing partQuote this item manually.

4 Installation Materials4.1 Typical Material Package

4.2 External Cable Suite

One-case delivery is adopted in the Chinese market. All typical auxiliary packages are not delivered or used.4.2.1 External Power Cables

04000434: OptiX OSN 500, external cable suite, including power cables for the cabinet, AC power cables, and UPM power cablesPart NumberDescriptionRemarksPricing/Configuring PartConfiguration Principle

S4022405Power Cable For Rack(Per Meter,16mm^2)-Pricing partConfigured based on the lower layer power cables

25030430Wire,450/750V,60227 IEC 02(RV)16mm^2,blue,85A,With a package exempted from fumigating48 V power cablePricing partIn a PDU, 48 V power cables, GND cables, and PGND cables are configured in a proportion of 2:2:1. By default, a 20 m long cable is delivered.

25030428Wire,450/750V,60227 IEC 02(RV)16mm^2,black,85A,With a package exempted from fumigatingGND cablePricing part

25030429Wire,450/750V,60227 IEC 02(RV)16mm^2,yellow green,85A,With a package exempted from fumigatingPGND cablePricing part

02235522OptiX,16mm^2 Power Cable Connector SetPower cable terminalConfiguring partOne piece is required for a PDU. If a single power cable is quoted independently, the power terminal is not configured by default.

04000474OSN 500 Chassis -48V DAC Power Cable and Connector Set(Blue,Black,For length30m)Configuring part

04000472OSN 500 AC Power CordsAC power cable for the OptiX OSN 500Middle layerOne piece (3 m long by default) is delivered for each set of equipment.

04000436External Suite,GIE 4805S Power CordsAC power cable for the UPMMiddle layerOne piece (3 m long by default) is delivered for each UPM.

The input power supplies to the chassis require left-angled power cables. The comparisons on left-angled female and straight female power cables between different countries are as follows.C13 Straight FemaleDescriptionC13 Left-Angled FemaleDescription

04020728External Power Cable,North America AC Power Cable,125V10A,3.00m,3*0.8mm^2,Black,PBSM,(18SJT(3C)),C13SF,W339404041271Outsourced Cable, North America Power Cable 125V13A 3.00m,3*1.3mm^2,Black,B-Type Straight Plug Male,(UL)16SJT(3C),C13 Left-Angled Plug Female

04040887External Power Cable,Japan AC Power Cable 125V12A,3m, 3*1.25mm^2,Black,PBSM,HVCTF-1.25^2(3C),C13SF04041114Outsourced Cable,Japan Power Cable 250V10A 3m,B-Type 3PIN Straight Plug /HVCTF3x1.25mm^2Black/3PIN Left-Angled Connector

04040888Australia Power Cable 250V 10A,3m,3*1.0mm^2,Black,I-Type 3PIN Straight Plug,H05VV-F-1.0^2(3C),3PIN Straight Connector04041115Outsourced Cable,Australia Power Cable 250V10A,3m,3x1mm^2 Black,I-Type 3PIN Straight Plug,H05VV-F 3x1mm^2,3PIN Left-Angled Connector

04040889Hong Kong Power Cable 250V10A 3m,D-Type 3PIN Angled Plug /HVV05F 3x1.5mm^2Black/3PIN Straight Connector04041116Outsourced Cable,Hong Kong Power Cable 250V10A 3m,D-Type 3PIN Angled Plug /HVV05F 3x1.5mm^2Black/3PIN Left-Angled Connector

04040890Britain/Singapore/Hong Kong Power Cable 250V10A 3m,G-Type 3PIN Angled Plug /HVV05F 3x1.5mm^2Black/3PIN Straight Connector04041117Outsourced Cable,Britain/Singapore Power Cable 250V10A 3m,G-Type 3PIN Angled Plug /HVV05F 3x1.5mm^2Black/3PIN Left-Angled Connector

04041056External Power Cable,Europe AC Power Cable,250V10A,3m,3x1.0mm^2 Black,PFSM,H05VVF 3x1.0mm^2B,C13SF04041118Outsourced Cable,Europe 11 Countries Power Cable 250V10A 3m,F-Type 3PIN Straight Plug /H05VVF 3x1.0mm^2Black/3PIN Left-Angled Connector

04041104China Power Cable 250V10A 3m,I-Type 3PIN Straight Plug /227IEC53(RVV)3x1mm^2Black/3PIN Straight Connector04041272Outsourced Cable,China Power Cable 250V10A 3m,I-Type 3PIN Straight Plug /227IEC53(RVV)3x1mm^2Black/3PIN Left-Angled Connector

04041119Switzerland Power Cable 250V10A 3m,J-Type 3PIN Straight Plug /HVV05F 3x1mm^2Black/3PIN Straight Connector04041280Outsourced Cable,Switzerland Power Cable 250V10A 3m,J-Type 3PIN Straight Plug /HVV05F 3x1mm^2Black/3PIN Left-Angled Connector

04041120Italy Power Cable 250V10A 3m,L-Type 3PIN Straight Plug /HVV05F 3x1mm^2Black/3PIN Straight Connector04041281Outsourced Cable,Italy Power Cable 250V10A 3m,L-Type 3PIN Straight Plug /HVV05F 3x1mm^2Black/3PIN Left-Angled Connector

04047785Argentina Power Cable 250V10A 3m,I-Type 3PIN Straight Plug /H05VV-F 3x1mm^2Black/3PIN Straight Connector04041115Outsourced Cable,Australia Power Cable 250V10A,3m,3x1mm^2 Black,I-Type 3PIN Straight Plug,H05VV-F 3x1mm^2,3PIN Left-Angled Connector

04150258Power Cable,3.0m,0.75mm^2,Black(Brown,Blue,Yellow/Green),CH10S3,H05VV-F 3G0.75 NBR13249,C13 Straight Connect,Brazil AC Power Cable

4.2.2 E1 Cables


S402240621E1 Cable(Per Meter,75ohm,Shield)21xE1 75-ohm cable, using middle-layer fuzzy pricingPricing partFor detailed mapping, see the configuration.

S402241221E1 Cable(Per Meter,120ohm,Shield)21xE1 120-ohm cable, using middle-layer fuzzy pricingPricing part

S1018225OSN 500, Trunk CableMiddle layer Pricing part

25050014Twisted-Pair Cable,100ohm,Category 5e UTP,0.51mm,24AWG,8Cores,PANTONE 430U,Use with Plug:14080082Network cable, a 10-m cable being quoted for each RJ45 interfacePricing part

4.2.3 E3/T3 Cables


S4023169E3/T3 Cable(Per Meter,75ohm)E3/T3 cable, using middle-layer fuzzy pricingPricing partConfigured based on the lower layer cables

04041166Trunk Cable,E3/T3 Trunk Cable,30m,75ohm,5.8mm,SMB75SF-VI,RG59/UPricing partConfigured based on the lower layer cables

4.2.4 Others

Part NumberDescriptionFeaturePropertyConfiguration Principle

04120309Trunk Cable,10m,75ohm,3.9mm,SAA75SM-I,SYV75-2/0.34(S)Quoted itemConfigure this item based on 34100104.

4.3 External Optical Fiber Suite

4.3.1 Optical Fibers


S4024281Optical Patch Cord (PCS)Middle-layer fuzzy pricingPricing partFor details, see the associated boards.

4.3.2 Optical Attenuators

Part NumberDescriptionRemarksPricing/Configuring PartConfiguration Principles

S4021159Fixed Optical Attenuator (PCS)Pricing partThis item is not recommended.

45030021Fixed Optical Attenuator,1310/1550nm-5dB-LC/PC->45dB



45030036Fixed Optical Attenuator,1310/1550nm,7dB,LC/PC,>45dB


45030040Fixed Optical Attenuator,1310/1550nm,3dB-LC/PC,>45dB

45030005Optical Fixed Attenuator,1310nm/1550nm,7dB,FC/PC,40dB

45030007Optical Fixed Attenuator,High Return Loss,1310/1550nm,5dB,FC/PC

45030008Optical Fiber Fixed Attenuator(10dB)

45030024Fixed Optical Attenuator,1310/1550+/-20nm,5dB,SC/PC,40dB

S4024294Optical Tunable Attenuator (Signal Channel, PCS)Pricing partThis item is not recommended.

45030016Optical Tunable Attenuator,Manual(Single),1300~1610nm,2~30dB,2.0dB,40dB,2mm*2.5m LC/PC

4.3.3 Fiber Adapters


02234576Optical Product Line,External Adapter SetMiddle layer

14130001Adapter,FC-FC,2,Silvery white,Shell:Metal,Sleeve:Zirconia,RoundPricing partThis item is not recommended for the OptiX OSN 500. For details, see the associated boards.

14130073Adapter,FC-FC,2,Silvery white,Shell:Metal,Sleeve:Zirconia,Square

14130157Adapter,SC-FC,2,Blue,Shell:Plastic,Sleeve:Zirconia,Square

14130248Adapter,LC/PC-LC/PC,2,Blue,Shell:Plastic,Sleeve:Zirconia,Square

14130258Adapter,SC/PC-SC/PC,2,Blue,Shell: Plastic,Sleeve:Zirconia,Shutter:Plastic,Square

14130134Adapter,SC-SC,2,Blue,Shell:Plastic,Sleeve:Zirconia,Square

14130249Adapter,2LC/PC-2LC/PC,4,Blue,Shell:Plastic,Sleeve:Zirconia,Square

14130133Adapter,2SC-2SC,4,Blue,Shell:Plastic,Sleeve:Zirconia,Square

14130357Adapter,MTRJ,MTRJ,2,Black,Shell:Plastic,Square

4.4 Accessories

4.4.1 Software Packages


05114477OptiX OSN 500 V100R002C01,Physical Software Package For OptiX OSN 500,DVDSoftware package DVD for the OptiX OSN 500 V100R002C01Configuring partOne item is configured based on the quotation version or if the quotation personnel requires.

05115288OptiX OSN 500 V100R005C00,Physical Software Package For OptiX OSN 500,DVDSoftware package DVD for the OptiX OSN 500 V100R005C00Configuring part

05115717OptiX OSN 500 V100R005C02,Physical Software Package For OptiX OSN 500 ,DVDSoftware package DVD for the OptiX OSN 500 V100R005C02Configuring part

05115736OptiX OSN 500 V100R002C01SPC150,Physical Software Package For OptiX OSN 500,DVDSoftware package DVD for the OptiX OSN 500 V100R R002C01SPC150Configuring part



05116092OptiX OSN 500 V100R006C00,Physical Software Package For OptiX OSN 500,DVDSoftware package DVD for the OptiX OSN 500 V100R R006C00Configuring part



4.4.2 Auxiliary Materials

Part NumberDescriptionRemarksPricing / Configuring PartConfiguration Principles

02230AXKOptiX OSN 500,OSN 500 Delivery Accessory Per AC Power Rack(Local standard AC Power Cable not included)This item covers PGND cables, 19-inch cabinet installation kit, and 18 RJ-45 connectors. By default, only PGND cables are delivered.Configuring partConfigure one item for each AC-powered chassis. This item is not required if the chassis is provided an item with a part number of 02230BST or 02230BSU.Note:

02230AXK is the pricing part when select Type of accessories is separated. Otherwise 02230AXK is the engineering survey item.

02230AXHOptiX OSN 500,OSN 500 Delivery Accessory Per DC Power Distribution RackThis item covers power cables, 19-inch cabinet installation kit, and 18 RJ-45 connectors. By default, only power cables and PGND cables are delivered.Configuring partConfigure one item for each DC-powered chassis. This item is not required if the chassis is provided an item with a part number of 02230BSR, 02230BSS, 2230BSV, or 02230BSW.Only for the region except India.

Note:

02230AXH is the pricing part when select Type of accessories is separated. Otherwise 02230AXH is the engineering survey item.

02230NLKOptiX OSN 500,OSN 500 Delivery Accessory Per DC Power Distribution Rack ,For India(cable tie not included)This item covers power cables, 19-inch cabinet installation kit, and 18 RJ-45 connectors(except cable tie). By default, only power cables and PGND cables are delivered.Configuring partOnly for India.

02233403OptiX Metro 500,Delivery Accessories As Per CabinetThis item covers tubes and wire fixing seats.Configuring partConfigure one piece for each cabinet that house only case-shaped equipment.

02239792Expansion Auxiliary Materials Package(10 cables needs 1 package)This item covers self-sealing plastic bags and blank labels.Configuring partConfigure one piece for 32xE1 services.Only for the region except India. 29041060 used for India.

25050014Twisted-Pair Cable,100ohm,,Category 5e UTP,0.51mm,24AWG,8Cores,PANTONE 430U,Use with Plug:14080082Configuring partThis item is used for assembling cables on site that are connected to power input/output port, transparent data ports, and NMS ports. By default, a 30 m long cable is delivered for a 4 x FE/GE port board, and a 50 m long cable is delivered for a board with more than four FE/GE ports.

14080082Network Interface Connector,8Bit 8Pin,Crystal Plug,Matching 25050014Configuring partConfigure two pieces for each network port, and configure two additional pieces for redundancy. RJ45 connectors are not configured if network cables are delivered independently.

04044726Single Cable,120ohm To 75ohm Clock Cable,30m,MP8-II,120CC4P0.4P430U(S)+4*SYV75-2/0.34(S)120-ohm to 75-ohm clock cableConfiguring partOne item is configured for one system control board if a 75-ohm clock is required.

14040199Coaxial Connector,SMB-75ohm,Straight/ Connector-Male,Matching SYFVZ-75-1-1,Gild Electroplating,For OEMDelivered in bulksOne item is configured for one E1 interface if delivered in bulks is required.

14040200Coaxial Connector,SMB-75ohm,Straight/Connector,Female,Matching SYFVZ-75-1-1,Gild ElectroplatingDelivered in bulks

14040375Coaxial Connector,BNC,75ohm,Straight Plug,Male,Matching SYFVZ-75-1-1,With Heat Shrink Tube With ItselfDelivered in bulks

14040327RF Coaxial Connector,L9,75ohm,Straight Plug,Male,Matching SYFVZ-75-1-1Delivered in bulks

14040395Coaxial Connector,L9,75ohm,Female,Straight Plug,SYFVZ-75-1-1(A),Outer Body Plating NickelDelivered in bulks

28010026Insulation Material,Fireproof PVC Corrugated Tube,D25The insulation material is used to protect optical fibers. One corrugated tube can contain a maximum of eight optical fibers.Configuring partLength of the corrugated tube is equal to the length of fiber jumpers, and the quantity of corrugated tubes is obtained by rounding up one eighth of the quantity of fiber jumpers.This item is not delivered by default.

28010216Insulating Material,Wound Tube,D12,white translucenceThe insulation tube, with an outer diameter of 12 mm, is used to protect optical fibers.Configuring partThis item is not delivered by default. Unless otherwise specified, this item is delivered according to the engineering survey.

28010158Wound Tube,Diameter 6mmThe insulation tube, with an outer diameter of 6 mm, is used to protect optical fibers.Configuring partThis item is not delivered by default. Unless otherwise specified, this item is delivered according to the engineering survey.

21100144Nonmetal Parts,DKBA0.480.0457-GT-300I- Wire Clip-300*3.6mm-Strenth 18.2kgCable tieConfiguring partThis item is not delivered by default.

29041060Engineering/Blank label,Engineering label,Signal Cable label,30 Groups,10 Array,3 Row,Height 22.0,Width 84.0,Matte White,1Pcs/GroupSignal cable labels, which are used to identify external cables and pigtail fibers rather than power cables. One large-sized label consists of 30 small-sized labels.Configuring partThe quantity of signal cable labels is obtained by rounding up one fifteenth the sum of cables (excluding power cables) and fiber jumpers.A cable that receives and transmits signals using different connectors is equal to two cables. This item is required only when neither 02230AXK/02230AXH nor 02239792 is delivered.

02080500Line Distribution Equipment,WFD-1,Port Protective Unit, For Single PortSurge-protection unitPricing partConfigure one piece for each port that connects to outdoor equipment.

28010210Insulating material,fire resistant PVC trough, 39*18mm,2m/pcs39 mm x18 mm, 2 m longConfiguring part Configure one piece if the required PVC trough length is less than or equal to 2 m. If the required PVC trough length (L) is greater than 2 m, the quantity of PVC troughs is obtained by rounding up L/2.

28010061Insulating Material,Fire-Resistance PVC Elbow-Not Fulfilled Environment Protection,39*1839 mm x 18 mmConfiguring partConfigure one piece for each PVC trough if the PVC trough length is less than or equal to 2 m. If the required PVC trough length (L) is greater than 2 m, the quantity of every item is obtained by rounding up L/2.

28010038Insulating Material,Fire-resistant PVC connector-Not Fulfilled Environment Protection,39*18Configuring part

28010033Insulating Material,Fire Retarded PVC Terminal-Not Fulfilled Environment Protection,39*18Configuring part

28010159Insulating Material,Fire Retarded PVC Wiring Trough-Not Fulfilled Environment Protection,100*40,2m/PCS100 mm x 40 mm, 2 m long Configuring partConfigure one piece if the required PVC trough length is less than or equal to 2 m.If the required PVC trough length (L) is greater than 2 m, the quantity of PVC troughs is obtained by rounding up L/2.

28010160Fire Retarded PVC Wiring Trough Angle Joint-Not Fulfilled Environment Protection,100*40100 mm x 40 mm, 2 m longConfiguring partConfigure one piece for each PVC trough if the PVC trough length is less than or equal to 2 m. If the required PVC trough length (L) is greater than 2 m, the quantity of every item is obtained by rounding up L/2.

28010161Fire Retarded PVC Wiring Trough Joint-Not Fulfilled Environment Protection,100*40Configuring part

28010168Insulating Material,Fire Retarded PVC Terminal-Not Fulfilled Environment Protection,100*40Configuring part

26010226Cross Recess Head Self-Threading Screw (GB9074.19-88) ST4.2*32,Pointed End,C TypeThis item is used to fix a PVC trough and used together with the item with a part number of 28010104.Configuring partConfigure 20 pieces if the required PVC trough length is less than or equal to 2 m.If the required PVC trough length (L) is greater than 2 m, the quantity is equal to 20 times the rounded up L/2.

28010104Plastic Expansion Tube,For Wood Screw Fixed On Wall,6*26This item is used to fix a PVC trough and used together with the item with a part number of 26010226.Configuring part

4.4.3 Installation kit


02237603OptiX OSN 500,Suite Of Installation PartsMiddle layer

02237613OptiX OSN 500,SubRack Suit for DeskConfiguring partSelect an appropriate item based on the installation mode. Configure one piece of each chassis.

02237614OptiX OSN 500,Subrack Suit for 19'RackConfiguring part

02237615OptiX OSN 500,Subrack Suit for standard ETSI RackConfiguring part

02237616OptiX OSN 500,SubRack Suit for WallConfiguring part

5 Documentation02230CUS OSN 500,Documents AccessoryPart NumberDescriptionRemarksPricing/Configuring PartConfiguration Principles

31183560OptiX OSN 500 STM-1/STM-4 Multi-Service CPE Optical Transmission System Product Documentation-(V100R002_02)Pricing part

31184798OptiX OSN 500 STM-1/STM-4 Multi-Service CPE Optical Transmission System Product Documentation-(V100R005)Pricing part

31185369OptiX OSN 500 Multi-Service CPE Optical Transmission System Product Documentation-(V100R005C02_01)Pricing part




6 Packaging MaterialsPart NumberDescriptionRemarksPricing/Configuring PartConfiguration Principles

30000109Product Complete-set Packaging OptiX OSN 500Packing materialDelivered in bulksConfigure one piece for each OptiX OSN 500 chassis

7 Software PackagesPart NumberDescriptionRemarksPricing / Configuring PartConfiguration Principles

02239094OptiX OSN 500,Basic Software Package,V100R001(Per Subrack)Middle layer

88030CPNOptiX OSN 500,Basic Software Package,V100R002(Per Subrack)OptiX OSN 500 V100R002 software packagePricing partConfigure one piece for each set of equipment.

88030MVPOptiX OSN 500,Basic Software Package,V100R003(Per Subrack)OptiX OSN 500 V100R003 software packagePricing part

88030SYPOptiX OSN 500,Software Upgrade Fee(Per Subrack,R(N)->R(N+1))OptiX OSN 500 V100R005 software packagePricing part

88031DNTOptiX OSN 500,Basic Software Package,V100R006(Per Subrack)OptiX OSN 500 V100R006 software packagePricing part

88031VBBOptiX OSN 500,Basic Software Package,V100R007(Per Subrack)OptiX OSN 500 V100R007 software packagePricing part

88038301Software,OSN 500,Optional SoftwareSoftware upgrade packagePricing partConfigure one piece for each set of equipment if an upgrade is required. If the entire upgrade path spans over several upgrade processes, configure one piece for each upgrade process.

05000079OptiX OSN 500,IEEE1588V2 Basic Software FeeOptional softwareMiddle layer

88030UEPOptiX NGSDH,LSSN00GE01,GE SFP Interface License For Packet Service(Per Port)IEEE 1588v2 license filePricing partConfigure one piece if the IEEE 1588v2 function needs to be enabled.

81601304Product Complete-set Packaging OptiX OSN 500GE port licensePricing partConfigure one piece for each GE optical port. Suppored only by packet services

88031DQVOptiX OSN 500 MPLS-TP Basic Function License FeeMPLS-TP licensePricing partConfigure one piece if the MPLS-TP function needs to be enabled.

88031DPJOptiX OSN 550,TP-Assist Basic Function Fee(Per subrack)TP-Assist Basic FunctionPricing partConfigure one piece if the TP-Assist Basic function needs to be enabled.

88031VAWOptiX OSN 550,TP-Assist Enhanced Function Fee(Per subrack)TP-Assist Enhanced FunctionPricing partConfigure one piece if the TP-Assist Enhanced function needs to be enabled.

88031VAYOptiX OSN 500,Ring Protection Function Fee(Per Subrack)MPLS-TP Ring Protection FunctionPricing partConfigure one piece if the Ring Protection function needs to be enabled.

8 License80010249: OptiX OSN 500, License of Integrated STM-1/STM-4 Compatible Optical Transmission EquipmentPart NumberDescriptionRemarksPricing/Configuring PartConfiguration Principles

31070026Huawei License Certificate,(HW)License certificateConfiguring partBy default, no printed license certificate is delivered. If required, configure one piece.

80020518OptiX OSN 500,BASIC,Basic FeatureMiddle layer

81601396OptiX OSN 500,LTNHBASIC02,Basic Software FeeVersion-specific licenseConfiguring partFor the OptiX OSN 500 V100R002, do not configure this item. For the OptiX OSN 500 V100R005, configure this item, with a quantity equal to the quantity of the item with a part number of 88030SYP. For the OptiX OSN 500 V100R006, configure this item, with a quantity equal to the quantity of the item with a part number of 88030DNT.

80020422Feature,AdaptiveLM,SWUPGD,SW Upgrade Common FeatureMiddle layer

81800073Function,AdaptiveLM,LSW2UPGRADE,SW Upgrade licenseUpgrade licenseConfiguring partConfigure this item, with a quantity equal to the quantity of the item with a part number of 88038301.

Packet network

Packet network (R5)

TDM network (R2)

iiHuawei Proprietary and Confidential Copyright Huawei Technologies Co., LtdIssue 01 (2009-04-10)