1. Career Summary

3. Key Skills

2. Academics

PANKAJ JAIN Email: jain.pankh@gmail.com DOB: 07 August, 1989 Phone no.0047-40983385

I am a Bachelor of Technology in Electronics and communication engineering from National Institute of Technology-Bhopal and also hold a MBA in Project Management (Executive), working with ABB-Global Industries and Services Limited as a Process Automation Engineer(Design, Development and Commissioning) for Oil and Gas Domain. I am working within a team on cutting edge technologies & would like to work in a situation that demands high degree of excellence and that enables me to utilize and enhance my technical, analytical and also managerial skills and where I can juice out my best to achieve best for the organization and the team.

1) College & Passing Year: -Sikkim Manipal University, 2013Degree: - Master of Business Administration in Project ManagementGrades: - A2) College & Passing Year: - National Institute of Technology- Bhopal, 2011Degree: - Bachelor of technology in Electronics and communication engineeringGrades: - 8.98/102) College & Passing Year: - DAV college- Jalandhar, 2007Education: - Higher secondary (10+2), Grades: - 88.4% (State merit list & ranked 5th in Punjab school education board for Non-medical stream)3) School & Passing Year: - Arya model high school- Sultanpur lodhi, 2005Education: - Matriculation (10th), Grades: - 90.4% (State merit list & ranked 2nd in Punjab school education board for Kapurthala district)

1) Distributed Control System (800xA System: v5.1 FP4 and v5.0 SP2)In depth knowledge of Various AC800M & AC800M HI Controllers such as PM861, PM864, PM864A,PM866, PM891, PM865 with S800IO Series2) Communication Protocols: MODBUS (TCP/IP, RTU), Profibus, Foundation field Bus, MLink, Profinet, AutrofieldBus, OPC3) NORSOK STANDARD I-002 and I-005: REUSE Library (AC800M &AC400M)4) IEC61508/61511: Functional safety standards for oil and gas sector5) Autronica: AutroSafe configuration tool version 4.1.3, 4.1.4, AS2000 Loop diagnostic tool6) Change Management: ProCoSys (Statoil), Remedy-change management 7.6, SAP Notifications7) Engineering Tools: Control builder M, Function designer, Graphic builder (PG2, VB), Autrosafe Configuration tool, Woodward PLC, Control Designer8) Blast Furnace Library: v1.0.09) System Knowledge: System architecture, Network setup, administration & security, OPC Communication.10) Design Documents: Design, preparation, review and implementation of GA drawings, control narratives, P&ID’s, System control diagrams (SCD), Cause & Effect sheets, Flowcharts11) Microsoft Tools: Microsoft office, Microsoft projects, Office 36512) Soft Skills: Certified proficiency in English (IELTS 7.5), Business communication skills, Creativity in problem solving and decision making, Cross Cultural Skills, Business Etiquette13) SAP: SAP 7300.1.1.97 Advanced user Skills14) Instrumentation: Calibration, Troubleshooting, Maintenance as per NORSOK standards15) Oil and Gas Process: In-Depth Knowledge of Process and Technical Safety Aspects from operational view. Both onshore-offshore experience.16) Interfaces: ACE, Barrier Status Panel (BSP), OLGA and other PIMS applications

Page 1

4. Trainings and Certifications

5. Professional Experience

Certifications:-Certified in 800xA System- Engineering with Control Builder MCertified in 800xA System- AC800M High Integrity and Maintenance Certified in 800XA System- Administration and MaintenanceCertified in 800XA System- Application ModificationCertified in 800XA System- Engineering with Human Interface systemCertified for FSE- Low-voltage and high-voltageCertified for Ex-BasicCertified for Basic offshore safety induction and emergency training (COENS 97345700171214004)Certified For Basic safety training (Falck 5834408)Quality Management Trainings:-Functional Safety Management (FSM) procedures for OGP NorwayQuality Management System (QMS) Awareness for engineering and servicesBusiness Etiquette Cross Cultural SkillsCreativity thinking in Problem Solving / Decision MakingProject Management Trainings:-Project Management & Execution BasicsEnterprise Content Management (ECM)ABB Project Management Framework Technical Trainings:-System Engineering: ¨AC800M Safety HI, Control builder M, Function designer, Information management, System administration and maintenance, REUSE, HMI & PC toolkit Library, Change Management, Remedy, ACS800 Drive Basics, Reuse Solutions on Oil & Gas Basics , PMS Basics, Telecom for Oil & Gas Applications, OPC Basics, Fire & Gas Detector Basics, Modbus Basics, Process Control Basics, Instrumentation Basics, Gas Turbine Fundamentals, PROFIBUS Basics, Piping and Instrument Diagrams (PIDs) Legacy, 800xA Hardware Engineering, Closed Loop Control Systems, Public Address System , Public Address System, Basics of SCADA and RTU, System Control Diagram Basics, Foundation Fieldbus Basics, CCTV Basics    International Standards: NORSOK Standards, IEC 61508/61511Communication Protocols: Modbus, PROFIBUS, OPCProcess Trainings: FPSO Process, Oil & Gas Process, Cement Manufacturing Process, Pulp & Paper Process, Telecom for Oil & Gas, Power Management System (PMS) & Process control, Processing Line in Cold Rolling Mill Complex of a Steel Plant Instrumentation Fundamentals: Gas Turbine, Fire & Gas Detector, ACS800 driveInformation Security Trainings:-CYBER SECURITY Module, IS WORKPLACE SECURITY Module, Basic Module, Phishing ModuleHSE Trainings:-Safety Aspects at Site Works, Low-voltage and high-voltage FSE, Basic Offshore Safety Induction and Emergency Training (BOSIET), Basic Safety Training - Falck Safety Services (Global), License 5834408Major Training@ NIT-B: GAIL (India) Ltd, Vaghodia, under Instrumentation and Control System department Minor Training@ NIT-B: ALTRUIST PVT LTD, Chandigarh as a study on “Effectiveness of customer communication” under guidance of AIRTEL team.

Organisation: - ABB GISL, Indian Operation Centre, BangaloreDesignation: - Process Automation EngineerDuration: - From 25 June.2011 to present

Page 2

Major Responsibilities: 1) Engineering , Logic design, testing & commissioning, 2) Testing of software control logic as per established and prepared procedures.3) Preparation/Review of FDS, DFDS, IO schedule and other quality documents.4) Ensuring deliverables are submitted within given time-frame and meet quality standards.5) Making ready to use engineering templates to achieve higher engineering efficiency.6) Execution of system design changes as per IEC 61508/61511 Standards.7) Assistance to Operations for Oil and Gas operators at their premises.

Projects Done: A) Name: GOLIAT FPSO, Norway Location: Bangalore (India), Ulsan (South Korea), Oslo, Hammerfest and Offshore, NorwayCustomer: ENI Norge, Hyundai Heavy IndustriesDuration: 18June, 2012-presentSystem details: 800xA System 8.3-1, AC800M HI, REUSE library, Autrosafe (AS) configuration tool ver4.1.3, Remedy 7.6, ProCoSys, OLGA, Woodward (Micronet) PLCRole: Control and Instrumentation commissioning engineer Onshore SAS Control Specialist (Technical Support Group-ENI Norge operations)Responsibilities undertaken:

SAS (Control System) Specialist: (Hammerfest, Norway & Sporadic Offshore-Technical Support Group)1) Preparation and execution of Preventive Maintenance and Corrective Maintenance.2) Preparation/Verification of Commissioning Test Procedure for Proof testing Safety Systems.3) Investigations in case of Shutdowns and Recommendations to prevent future occurrences4) Technical support to D&T (Stavanger) and technical Authority (TA) Stavanger.5) Preparation of Daily checklist for SAS maintenance offshore.6) Preparation of work packages to execute upgrade jobs on Control System7) Technical Support to Process system owners (Hammerfest) and preparation of changes on SCD and P&IDs.8) Participation in reviewing technical Safety barriers and ensuring the same9) Co-ordination offshore for troubleshooting and training on Systems10) Act as interface between various applications developers for control system (ACE, BSP etc.) and control system regarding challenges from both sides.11) Handover of commissioning knowledge to current operation team.12) Offshore rotations for troubleshooting and commissioning assistance in Fire and Gas Systems, Gas turbine, Inert gas generators, Fresh water system packages etc.13) Change management via SAP following ENI ENIMS processes. Commissioning: (HHI Yard, South Korea & Offshore, Norway)1) Modification of Process and Safety applications as per IEC61508/61511 standards.2) Validation/Review of changes and Impact analysis documentation3) Powering up and troubleshooting of Hardware panels, RIO etc.4) Configuration/Modification/Testing of Autronica loops with Autrosafe configuration and Diagnostic tool.5) Commissioning of SAS and Independent packages like Emergency Diesel Generator (FRAMO), Fire water pumps (FRAMO), Mooring System (AKER), and Ballast Pumps etc.6) Sea Trial for Goliat FPSO which lasted 18 days in Korean Sea as CCR Responsible.7) Validation of response of Fire Fighting Equipment and Systems as per NORSOK and NFPA20 Standards.8) Preparation, Testing and Execution of Shutdown and Cold Start procedure of Goliat FPSO 9) Troubleshooting of Field instruments and interface of multiple systems with ABB DCS 800XA10) Commissioning of GE-LM2500+ G4 Gas Turbine

Application Development & Testing: (Bangalore, India)1) Input review of design documents received like SCDs, P&Ids and Layouts.2) Development of Safety applications as per IEC61508/61511 standards.

Page 3

3) Code review, IAT and FAT for applications developed.4) Documentation, as per QMS standards, of application development & In-house testing.5) Configuration of Autronica software loops with Autrosafe configuration tool.6) Use of Change management tools such as REMEDY 7.6 throughout project.

B) Name : Black Canyon Fire and Gas Expansion Location: Bangalore (India), Houston (USA)Duration: 01 March, 2015 – 05 April, 2015Customer: Exxon MobilSystem details: 800xA System v5.1 FP4, AC800M, Control Designer toolRole: Development and Testing EngineerResponsibilities undertaken:1) Development and testing of customised Graphic elements and Faceplates as per Exxon Mobil specifications to match with existing MELODY system interfaces. 2) Development of MDS (Module Design specifications) and the test Procedure for the testing of all the customized software blocks as per SIL2/3 Standards.3) In House testing and documentation of Software code before delivering it for FAT. 4) Workplace configuration for single screen and multiscreen operator workplaces.5) Develop of HMI (Human Machine Interface) for the Fire and Gas layouts and various maintenance displays.6) Configuration of Silence HMI Buttons and Bypass for Detector in Launching Barrel as per Functional Design Specifications (FDS).7) Configuration of External Alarm Configuration and Navigation design for whole plant HMI along with Existing system 8) Configuration of Security rights and user restrictions for various users in the plant during operation. 9) Configuration and testing of various diagnostics signals in applications for both software and Hardware. 10) Confirmed write support access settings for IO tags as per SIL2 standards for FGS Applications. 11) Configuration of Historian server and corresponding Log Configuration for various IO Signals as per vendor specifications.12) Configuration of Alarm list and mapping of Priority to severity for all the signals as per HAZOP and LOPA analysis.13) Configuration of Trends and HMI for operator interface of the same.14) Configuration of default Views of Faceplate, default positioning and conversion of Faceplates from VB to PG 15) Preparation of M-test Procedures and implementation of vendor comments.16) Troubleshooting of various system issues.

C) Name: Blast Furnace-3 CommissioningLocation: Vishakhapatnam (India)Duration: 05February, 2012 – 27May, 2012Customer: Vizag Steel Plant-(VSP), System details: 800xA System v5.0 SP2, AC800M, Blast Furnace library, Modbus RTU, Plant SCADA Masibus, Paul Wurth Level-2 System, Kraft Panel (Transformers)Role: Commissioning EngineerResponsibilities undertaken:Graphic Development:1) Graphic development for Utilities, GCP, WTP Cast House Machines, Profilomter, In burden Probes etc.2) Testing of all the graphics during the cold commissioning of the areas involved.3) Modifications as per Operators requirement during and after the final commissioning of plants.

Page 4

6. Other Achievements

6. Passport details

4) Development of the graphical reports for the totalizers and Stock House.Application Development and Testing:1) Logic, Modbus (RTU) and MMS application development for Stock House and Cast House de-dusting, Profile meter, In burden probe, Cast House Machines, Report Generation and Level-2 Integration.2) Troubleshooting of the areas such as BLT, GCP, Pump House and Stoves as per requirement.3) Testing of the areas programmed on live system and tuning of the process.Hardware and Communications:1) Installation of servers and 800XA System for TRT.2) Troubleshoot of Networking problems and setup of operator stations as per network topology.3) Pre-Handover hardware inspection including redundancy test for power and network for each controller.4) Communication with SIEMENS DCS installed in Sinter plant with BF3.5) Communication with various 3rd party devices available such as Kraft, Hammon and TMT.6) Level-2 Communication with Paul Wurth system via OPC Communication.Documentation:1) IO List & Functional description document preparation for cast house operation.2) Testing procedure for Pre-Commissioning Hardware Inspection by L & T, M.N Dastur and VSP.3) Documentation of the various activities involved during the night shifts after the start-up.D) Name: EKOFISK-ZULU, EKOFISK-L (Norway)Location: Bangalore (India)Duration: 12September, 2011-03February, 2012System details: 800xA System 5.1RevA, AC800M HI, REUSE libraryRole: Project EngineerResponsibilities undertaken:HMI Development:- Design Input Review, Development and Testing for Safety and Process DisplaysApplication Development :- Development of ESD application for few NodesDocumentation1) Preparation of all the graphic typicals for ESD, PSD, PCS and Fire & Gas.2) Preparation of the test procedure for testing of the displays.System Administration:- Setup of the Test Systems for the team working in INOPC.E) Name: Baku Tbilisi Ceyhan pipeline (BTC), United KingdomLocation: Bangalore (India)Duration: 29July, 2011-09September, 2011 System details: 800xA System 5.0sp2, 800xA System 5.1FP1 Role: Testing EngineerResponsibilities undertaken:1) Conversion of Graphics from VB to PG2.2) Aspect linking of various displays involved 3) Look and feel analysis of all the displays involved4) Testing of the functionality of the graphics involved

1) Vice President of Electronics and Communication Engineer’s association (ECEA) MANIT, 2010-20114) First position in Circuit Designing during TECHNOSEARCH’08 in MANIT5) Executive member of ISTE student’s chapter 6) Public Relation Officer of INTELLECT BROWSERS CONSORTIUM (IBC) in MANIT, Bhopal7) Co Coordinator of TREASURE HUNT a brain storming event in TECHNOSEARCH, 20108) Member of college CHESS team9) Member of district team participating in TABLE TENNIS at STATE LEVEL

Name Pankaj Jain

Page 5

7. Address

Date of birth 07 August,1989Nationality IndianPassport Number J4105762Date of Issue 01-08-2011Date of expiry 31-07-2021Place of issue Jalandhar(Punjab)

Present Address#410, Hamnegata 7, Hammerfest 9600

Permanent AddressPankaj Jain, c/o Ravi Kant Jain, Mohalla Nasir Purian, Sultanpur Lodhi, Dist. Kapurthala, Punjab (India)-144626

The above information is correct to the best of my knowledge.

Place: Hammerfest, Norway Date: 19/07/2016 PANKAJ JAIN

Page 6