pg-us

7/30/2019 pg-us

1/24

PG 11-US

FAADE

FRAMING SYSTEMS

CONCRETE

7/30/2019 pg-us

2/24

HMS -Brick Tie Channels

HTU Cast-InChannels

HTACast-In Channels

HGB -Balustrade Fixings

HZA -DYNAGRIP Cast-In

Channels

HALFEN Framing System/Accessori es

HALFEN Framing Channelsand HALFEN Bolts

MBT

Connector

HBT

Rebend Connections

HIT

Balcony Connections

HBB

bi-Trapez-Box

HCC

Column Shoe

HSC

Stud Connector

HTT/HTF

Impact Sound InsulationElements

DETAN

Tension Rod System

FPAPrecast

Panel Anchors

SUKSub Struct ure

HK4brickwork support

system

UMAGrout-In Anchors

Body Anchor

ANCHORING SYSTEMS, FRAMING SYSTEMS AND ACCESSORIES

REINFORCEMENT SYSTEMS

PRECAST SUPPORT SYSTEMS, STONE SUPPORT SYSTEMS, BRICKWORK SUPPORT SYSTEMS, TENSION ROD SYSTEMS

Connection Solutions.The HALFEN Product range.

Paserelle Simone de Beauvoir, France

7/30/2019 pg-us

3/24 3 2012 HALFEN PG 11-US www.halfenusa.com

HALFEN Range

Concrete Products

7/30/2019 pg-us

4/244 2012 HALFEN PG 11-US www.halfenusa.com4

HALFEN HTA CAST- IN CHANNELS

HALFEN HZA DYNAGRIP TOOTHED CAST- IN CHANNELS

Almost any component can be installed

with HALFEN channels, e.g.: Curtain wall & concrete faades

Structural steel

Pipe support systems

Brickwork support

HALFEN HTA cast-in channels are

also ideal for all connections subject to

dynamic loads, e.g. for crane rails or

machine anchor points. Special hot-

rolled HALFEN HTA cast-in channels

are available for this purpose.

Particular quality features associated

with HALFEN channels are:

High load capacities

Suitable for cracked and non-cracked

concrete

Small edge distances

Easy to adjust

HALFEN cast-in channels are the ideal

basis for easy-to-install, adjustable con-

nections. A strip filler provides protec-

tion against ingress of concrete into the

channel.

Easy installation without noise,

dust or hand tool vibration

These quality features make HALFEN

channels an indispensable product for

all designers and users.

HALFEN HZA Dynagrip toothed cast-inchannels provide high dynamic and

static load capacities in all three-

dimensions. The interlocking teeth on

the channel profile and its matching

T-head bolts make it ideal for supporting

vertical loads while providing ample

adjustment for connections, e.g. Beam

end, shelf angle or heavy service

connections.

Quality features of HALFEN HZA

Dynagrip toothed channels are: Suitable for cracked and

non-cracked concrete

High tension, shear and longitudinal

load capacities

Suitable for high cycle dynamic loads

The product range consists of three

channel profiles:

HZA 29/20, HZA 38/23, and

HZA 53/34.

7/30/2019 pg-us

5/24 5 2012 HALFEN PG 11-US www.halfenusa.com 5

HALFEN HGB BALUSTRADE ANCHORS

HALFEN HGB channels and the matching

HALFEN high-tensile T-bolts enable the

safe anchoring of railing posts to the

edge of thin concrete slabs.

The special channel anchors allow high

performance connections to slabs with

thicknesses as low as 4 (100mm).

Quality features are:

Fast & adjustable connections

Safe and reliable load performance

in thin concrete

Available in short or long lengths,

in several load ranges

To compliment the wide range of

HALFEN HTA and HZA channels (seepage 4), HALFEN has developed the

HZA-PS range for structures requiring

particularly high levels of security and

performance.

Originally developed to meet the

dynamic and seismic load requirements

of the nuclear industry this range has

exceptional performance in heavily

cracked concrete.

Quality features of the

HZA-PS range are:

Suitable for concrete structures

designed for extreme conditions

Suitable for oscillating loads acting

in all directions

Suitable for applications in

earthquake areas

Special anchor form for safe

anchoring in severely cracked

concrete

The product range consists of three

channel profiles:

HZA-PS 29/20, HZA-PS 38/23 and

HZA-PS 53/34.

HALFEN HZA-PS TOOTHED CAST- IN CHANNELS

7/30/2019 pg-us


HTU cast-in channels enable rapid, wide

tolerance connection to concrete using

self-tapping screws.

HTU channels can be used for many

applications including the anchoring of

profiled metal facades or roofs; window

and door frames; or building services:


Suitable for tension and shear loads

Easy, large tolerance connections Available in hot-dip galvanized

and stainless steel

Selection of load capacities available

HALFEN HTU CAST- IN CHANNELS

HALFEN HMS BRICKWORK RESTRAINT SYSTEM

The HALFEN brickwork restraint system

is designed to tie brick and blockworkto concrete walls and columns. The

masonry is connected to the HALFEN

HMS channels by HALFEN ML ties. The

ties are positioned in the masonry joints

to horizontally restrain brickwork while

allowing vertical movement to reduce

the possibility of masonry cracking.

To enable concrete forms to be stripped

early, additional channel anchoring may

be achieved by using the optional bend

out anchors.


No drilling of blocks or concrete

required

Simple, inexpensive system

Also suitable for thin mortar joints

7/30/2019 pg-us


HALFEN MBT GRIP CONNECTOR

The HALFEN HIT balcony connection

can be used for the effective prevention

of thermal bridges and condensation

inside the building. Available in

modular units the system is available

in a wide range of types to suit most

concrete balcony applications.

Radiused balconies and corners are

easily accommodated by the range.

The system is also easily modified to

support external concrete walkways and

parapets.


Easy to install

Effective preventive solution for

thermal bridging and so significantly

reduces heat loss, the risk of internal

condensation, and mold growth

Suitable for poured in place and

precast balconies

Versatile design possibilities

HALFEN HIT BALCONY CONNECTIONS

The MBT reinforcement coupler is

used to butt join two reinforcing bars,

and effectively transfer the acting tensile

and compressive loads.

It is particularly suitable for the replace-

ment of damaged reinforcement; the

connection of old and new structures;

and the connection of precast concrete

units.

Quality features are: Safe and rapid connection

Short coupling lengths

No need to specially prepare the

bar ends (e.g. no thread cutting or

welding required)

7/30/2019 pg-us


HALFEN HBT REBEND CONNECTION

HBT rebend connections are used for

efficient reinforcement continuity in

concrete structures, that are poured

in subsequent phases. and have to be

connected.

The casing consists of galvanised

steel sheet with special flanges and apreformed hole to facilitate the removal

of the cover from the casing. It can be

simply nailed to the formwork or wired

to the reinforcement. The casing houses

special grade re-bendable reinforcing

bars available in many configurations to

suit various reinforcement patterns.


Casing provides excellent concrete

bond characteristics

Shallow casing enables easy

application in thin precast units

Many reinforcement configurations

available

Simplifies formwork design and

speeds construction.

The casing profile is specially designed

to provide defined bonding in concrete.

7/30/2019 pg-us


Structure-borne noise emanating

from the impact of footfalls and other

traffic in stairwells can be particularly

disturbing to occupants of both

residential and commercial structures.

Noise disturbance from stairwells not

only affects occupant comfort but

can also reduce the value of adjacent

tenancies.

The HALFEN bi-Trapez-Box offers an

effective solution by providing optimum

impact sound insulation, and structural

support for either poured in place or

precast concrete landings. Foot fall

noise is effectively dampened by the

design of the products special shell.


Effective noise reduction

Easy installation

Range of sizes

HALFEN bi -TRAPEZ-BOX IMPACT SOUND INSULATION

Sister products to the HALFEN

bi-Trapez-Box, HTT and HTF products

are used to acoustically separate

concrete stair flights from the structure.

Positioned at the interface of concrete

stair flights and landings or slabs, these

products effectively dampen noise

transfer from stair flights to the struc-

ture. Additional acoustic insulation is

provided by HALFEN HTPL joint sheetswhich are positioned both between stair

flights and adjoining walls, and between

landings and adjoining walls.


Excellent sound insulating properties

Wide range of sizes to suit varying

concrete thicknesses and bearing

capacities

HALFEN HTT/HTF IMPACT SOUND INSULATION

7/30/2019 pg-us


HALFEN HCC COLUMN SHOE

Conventional methods for the connection

of precast columns to foundations areoften unwieldy and expensive to produce,

transport and handle on the job site.

HALFEN HCC column shoes in conjunction

with HALFEN HAB anchor bolts solve

many of these problems.

HALFEN HCC column shoes are not only

used for the connection of columns to

foundations but also to form indepen-

dent rigid connections between precast

column segments, continuing through

floor slabs.


Extensive range of load capacities

Quick installation

Minimal or no propping during

construction

HAB anchor bolts may also be

used as foundation connections

for structural steel elements

HSC-S HSC-A

HALFEN HSC STUD CONNECTOR

The HALFEN HSC Stud Connector is

an innovative high performance system

that enables safe and economical con-

nections between corbels and concrete

columns.

By replacing complicated reinforcement

patterns the HSC Stud Connector allows

considerable time-saving and design

versatility.


Efficient transfer of high tensile

forces

Minimal embedment due to forged

head

Reliable fast assembly with greatly

reduced steel reinforcement

Also suitable for dynamic loads

Walls and columns can be cast

with simplified formwork; corbels

can be subsequently cast around

threaded HSC connectors

7/30/2019 pg-us


HALFEN HSC-B STRUCTURAL STEEL CONNECTOR

The HALFEN HSC-B structural steel

connector is an efficient method ofattaching structural steel components

to concrete. It is designed to safely

transfer very high forces into the

concrete structure. Tension loads, shear

loads, and bending moments (acting

separately or combined) can be safely

supported.


Outstanding performance

Minimal embedment depth

Cost-effective installation

The HALFEN HSD Shear Dowel System is

designed to safely transfer vertical shearloads between concrete elements that are

separated by movement joints.

Two versions of the product are available

in a range of load capacities. One version

allows horizontal movement to occur

only across the movement joint, while

supporting vertical shear loads. The

second version allows horizontal move-

ment both across and in the longitudinal

direction of the joint.

Quality features are: Safe transfer of vertical shear loads

into the concrete structure while

allowing thermal movement and shrin-

kage at joints

Simple installation to formwork

Manufactured from high quality stain-

less steel to prevent corrosion and

reduce thermal bridging.

High structural load capacities

HALFEN HSD SHEAR DOWEL SYSTEM

7/30/2019 pg-us


HALFEN HFR FIBRE GLASS REINFORCEMENT

Traditional structures use concrete that

is conventionally reinforced with carbonsteel reinforcing bars. This combination

of steel and concrete allows the support

of high loads and enables a great deal

of versatility in design. However, there

are numerous applications in concrete

construction where steel reinforcement

may not be the best solution.

Steel is subject to corrosion, and once

this process begins it causes expansion

forces in the concrete which result in

cracking and leading to expensive repair

bills. Stainless steel, galvanized steel, and

epoxy coated reinforcing bars are alter-

natives for high corrosion environments,

but each have their disadvantages based

on cost, life expectancy, or requirements

for special inspection and quality control.

Steel is also heavy, conducts electricity,

and affects magnetic fields. In certain

structures these attributes create design

problems.

For applications where steel reinforce-

ment is not an option the HALFEN HFRfiber glass reinforcement system can be

an excellent solution.

HALFEN in conjunction with the FIREP

Group has developed a range of inno-

F

iReP

F

iReP

vative reinforced fiber products with

outstanding material properties. Theresulting HALFEN HFR fiber glass

reinforcement system has approximately

twice the tensile strength of steel, while

only about a third of the weight. It is

corrosion-resistant and can be produced

in many reinforcement bending formats.

HALFEN HFR bars are produced using

a very special pultrusion process, during

which the surface of the bar is given its

ribbed bonding surface without exposing

or damaging the continuous fibers

running through the bar. This protects

the fibers against mechanical and

chemical damage and allows simple and

safe handling.


High tensile strength

Low weight

High corrosion/chemical resistance

Easy to cut to length.

No electrical conductivity,or electrostatic charge

Non-magnetic

Sealed bar surface

7/30/2019 pg-us

13/24 13 2012 HALFEN PG 11-US www.halfenusa.com 13H F ---- .w .. lll elllllllllll ....

HALFEN Range

Faade Products

7/30/2019 pg-us


HALFEN GROUT-IN ANCHORS TYPE UMA/UHA

HALFEN UMA grout-in anchors are

designed to support the weight of stone

faades and applied wind loads. They

may be grouted into either concrete,

filled CMU, or brickwork structures, and

are available in a wide range of types

and load capacities. Utilizing a dowel

restraint system, they may be used in

either the horizontal or vertical joints of

the faade.

Lighter duty HALFEN UHA grout-inanchors are designed only to restrain

stone faades against applied wind

loads and other horizontal forces. They

may be used in combination with the

UMA system.

HALFEN grout-in anchors are produced

in stainless steel for high corrosion

resistance and minimal thermal transfer.

HALFEN body anchors are adjustable

restraint and support products for stonefacades. Utilizing a dowel restraint system

the anchors require drilled holes in the

stone rather than conventional kerf slots.

This minimizes work in preparing the

stone, and reduces the risk of freeze-thaw

damage to the stone. The anchors offer

three dimensional adjustment, and can be

attached to the structure using HALFEN

channels or drilled bolts.

HALFEN body anchors are available in

four product ranges HRM, BA, DH and

DT. This selection provides a considerable

number of design options, catering for

various wind loads, stone weights and

cavity situations. All HALFEN body

anchors are produced in stainless steel

for high corrosion resistance and minimal

thermal transfer.


Fully pre-engineered solutions

Projections from 1 to 9

(40240 mm)

Adjustable in three directions

Can be used in either horizontal or

vertical joints

HALFEN BODY ANCHORS TYPE BA/HRM/DT/DH


High load capacities

Projections from to 12

(20300 mm)

Adjustable in three directions


vertical joints

7/30/2019 pg-us


HALFEN BRICKWORK SUPPORT SYSTEMS

HALFEN brickwork support systems

are used to transfer the deadweight

of brickwork facades to the structure.

They are normally used above horizontal

movement joints or openings, and are

connected to the structure using HALFEN

channels or drilled bolts.

All HALFEN brickwork support systems

are engineered to provide optimal load

performance from the minimal use of

material, while providing a high degree of

location adjustment. Consequently, thesystems are lighter and easier to install

than conventional shelf angles.

Most suitable for cavity sizes greater than

3 (75mm) these products are produced

in a wide variety of sizes and types, and

are available in stainless steel or hot dip

galvanized finish. The minimal contact

with the structure also reduces thermal

bridging across the cavity.


Excellent support across wide cavities

High degree of installation adjustment

Wide selection of sizes and load

capacities

Engineered to use minimal material

thicknesses so reducing thermal

bridging and reducing interference

with brick coursing

The HALFEN SUK system is a multi ad-

justable sub-frame system incorporatinganchors for the support and restraint of

stone facades. It is particularly suitable

for both new construction or refurbish-

ment projects with large cavities behind

the faade (cavity widths above 6

or 160 mm).

The system has a minimal number of

connections to the structure making it

very thermally efficient.


Suitable for very large cavities

Adjustable, light & high performance

support system

Can be installed to HALFEN channels

or using drilled bolts


vertical joints

HALFEN SUK

7/30/2019 pg-us


HALFEN ADJUSTABLE CONCEALED LINTEL SYSTEM

HALFENs technical department uses the

architects conceptual design to engineera brick lintel support system for each

specific opening. Unlimited combinations

using different brick size, span, coursing,

soffit depth and arch geometry can be

designed and manufactured to meet

project specifications.

Quality features are;

Unlimited span and soffit width can be

achieved, with connection (s) to the

structure

Available in hot-dip galvanized or

stainless steel

Field adjustable to allow for job site

conditions

Ships flat for ease of transportation,

handling and storage

Maintenance of exposed steel is

eliminated

Shop drawings and calculations are

provided for all conditions

Engineering State Stamp available

upon request

Virtually any flat or radiused masonry

opening can be built without exposed

steel using the HALFEN Adjustable

Concealed Lintel System (HACLS).

Commercial, government, institutional,

religious and high-end residential projects

can now have all brick soffit masonry

openings that are aesthetically pleasing

and maintenance free.

The HACLS is designed to provide

hidden support for brick soffits, allowing

the brick to remain the architectural

focal point of the openings.

7/30/2019 pg-us


The HALFEN curtain wall support system

provides a range of adjustable supportbrackets for use with curtain wall faade

systems. HALFEN HCW brackets are

used in conjunction with HALFEN

channels to provide a fast and simple

method of restraining both the weight

and wind loads imposed on the faade.

The system may be used on either steel

or concrete framed structures, and is

available in several variations to enable

rapid mullion installation to either the

top or edge of floor slabs and beams.

HALFEN HCW CURTAIN WALL SYSTEM

The DETAN rod system is used for

structural bracing where an architectural

or aesthetic quality is also required.

DETAN ROD SYSTEM

tension rod

locking nut

fork end

pin

circlip

anchor disk

The system is composed of rods,

which are adjustable for length, plus

a comprehensive range of matching

accessories such as fork ends, anchor

disks and cross couplers.

Available in very high strength carbon

and stainless steels the system is avail-

able in a wide range of rod diameters

making it suitable for a huge range ofapplications.

Typical uses are as follows:

Exposed bracing for timber and steel

structures.

Bracing for glass facades.

Pedestrian bridge bracing.

Bracing for canopies and sun shades.


Concealed length adjustment

Simple installation

Attractive appearance

Rod diameters from to 3

(6mm- 95mm)

High load performance


Fast and safe connections without

welding or drilling

Installed without special tools

Easy installation adjustment in up to

three directions

High load-bearing capacities

Close edge distances

7/30/2019 pg-us


HALFEN BRA PARAPET CORBELS

HALFEN BRA Parapet corbels are used

to connect precast parapets or facade

panels to reinforced concrete slabs.

The design of the system absorbs the

bending moments of the panel.

The BRA system is first cast into the

precast panel, then anchored to the

structure by bolting to a HALFEN

channel which has been cast into a

recessed pocket in the floor slab. Theposition of the panel can be adjusted

in three dimensions.


Reduced thermal bridging

Designed in stainless steel for high

corrosion protection

Very fast to install without welding

or drilling

The HALFEN FPA precast panel anchor

system provides a range of adjustableconnection systems to support the

weight of precast concrete faade

panels. It is ideal for large cavities with

small to medium size precast panels. All

system components are pre-engineered

and made of stainless steel. This provides

excellent corrosion resistance and mini-

mizes thermal transfer.

Additional accessories are available

within this product range to support

applied wind loads.


Simple and quick installation

Adjustable in all directions

Connections to the structure are

made using HALFEN channels or

drilled bolts

HALFEN FPA PRECAST PANEL ANCHORS

7/30/2019 pg-us

19/24 19 2011 HALFEN PG- US 2/11 ww w.halfen.com 19

HALFEN Range

Framing Products

7/30/2019 pg-us


The HALFEN framing system is a com-

prehensive line of lipped steel channels,

matching t-bolts and accessories, used

for the connection of steel components

and subassemblies.

The system provides mechanical

engineers and machine builders with an

adjustable bolted connection, offering

many advantages over welding or drilling

in the manufacture of equipment orcomplex supporting structures.

HALFEN has the largest range of

channels and t-bolts available world-

wide, aimed at the specialist designer

who requires consistently high-quality

and absolute reliability.

The following channel systems are

available;

Light and medium duty HALFEN cold-

formed channels:

A strut-type system, but with a much

wider selection of channel profiles, to suit;

Light fabrications

Low load assemblies

Non-structural connections

Structural connections with low

performance demands

Heavy duty HALFEN hot-rolled channels:

Ideal for high demand connections

beyond the capacity of cold-formed

channels requiring;

Dynamic load resistance

High torque connections

Mechanically interlocking

connections using toothed channels

and toothed t-bolts

HALFEN FRAMING CHANNELS

Heavy, medium and light duty systems

are available in mill finish, galvanized

and stainless steel material.

7/30/2019 pg-us


Halfen framing channels and T-bolts are

the high value alternative to cutting and

welding or drilling stock steel sections to

connect components, and are frequently

an alternative to proprietary aluminum

structural framing and assembly systems.

Key benefits:

A wider margin of tolerance means

lower production costs, reduced re-

work and fewer out of specification

rejects

Machines are more easily modified or

upgraded while in service on-site or

at the customers premises

Doppelmayr

D

oppelmayr

HALFEN FRAMING SYSTEMS APPLICATIONS

The basis of a modular production

system is an adjustable a fixing system,which is flexible over the complete life

of the machine, from design, to produc-

tion, servicing, repair and upgrade.

Materials handling and production

line equipment

Industrial dryers, kilns and ovens

Mills and crushing equipment

Recycling and waste processing

machines

Heavy skid applications

Fabrications for power, gas turbine

and heavy electrical sectors

Rolling stock

Specialty and emergency vehicles

Chairlifts and ropeways

Cargo restraint

HALFEN framing channels and t-bolts

are used by world leading OEMs,

machine builders and engineering firms

as an integral part of their fabrications

to connect sub-assemblies.

Reduced parts inventory fewer

components can suit a wider range

of machines

Shorter design, production and

selling cycle begin production

before final design has been detailed

or before confirmation of final

specification by the client

The HALFEN framing system allows

machine builders to provide customized

solutions to their clients, using modular

production techniques.

The adjustable bolted connection

provided by HALFEN channels and bolts

has many advantages over welding or

drilling.

7/30/2019 pg-us


More than 170 types of channel and

400 types of t-bolts makes the HALFENframing system the broadest range

worldwide.

Hot-rolled HALFEN channel is the

adjustable connection of choice for

mechanical engineers.

Above Hot-rolled channel is torqued

to resist vibration in a gearset assembly.

Replacement work is easily performed at

the customers premises.

Above Roller axles can be placed in

any position along the side support

frame. The same frame can be used for

any model dryer.

S

iemensAG

HALFEN FRAMING SYSTEMS APPLICATIONS

Below HALFEN hot-rolled channel

provides an adjustable bolted connection

to attach a heavy radiator mounting to

a structural steel frame.

7/30/2019 pg-us


HALFEN Powerclick is an innovative in-

dustrial pipework support system.

Designed for high beam and column loads

the system replaces much heavier, site

or shop fabricated structural steel pipe

support frames. Extremely versatile, the

system has a small number of componen-

ts that can be combined to create a huge

variation of support applications.

The Poweclick 63 system comprises: One adjustable beam/column profile

for most pipe support applications

One corner connector in two

variations provides 112 frame designs

One base plate type

One beam clamp for connections to

most flanged steel beams

Industrial facilities with a small stock of

Powerclick on-site can quickly fabricate

almost any support frame to suit new or

upgraded pipe layouts.

Simply cutting the Powerclick profiles

to the required length and combining

them with the 3 other components does

away with custom welded fabrications,

saves a significant amount of design and

installation time, and does not require

hot-work permits or plant shutdown.


Extremely versatile multi-adjustable

support frame system

Very few components

Low weight

High load capacity

Simple bolted assembly, no welding

or drilling

Hot dip galvanized finish

HALFEN POWERCLICK FRAMING SYSTEM

7/30/2019 pg-us

24/24

CONTACT HALFEN WORLDWIDE

www.halfen.com

HALFEN has a g lobal network of Subs idiary Companies to ass is t you. The main contact in format ion

for North Amer ica, Europe and As ia i s provided below. For a fu l l l i s t of of f i ces please v is i t

www.hal fen.com

HALFEN GmbH shall not accept liability for the accuracy of the information in this publication or for any printing errors.

HALFEN is also represented by distributors in Argentina, Australia, Azerbaijan, Belarus, Brazil, Bulgaria, Chile, Colombia, Croatia/Bosnia-Herzegovina/FYROM/Montenegro, Cyprus, Estonia, Greece, Hong Kong, Hungary, Indonesia, Ireland, Israel, Jordan, Kingdom of Saudi-Arabia, Latvia,Lebanon, Lithuania, Luxembourg, Malaysia, Malta, Mexico, New Zealand, Peru, Philippines, Republic of Kazakhstan, Romania, Russia, Serbia, Singapore,Slovenia, South Korea, Taiwan/ROC, Thailand, Turkey, Ukraine, United Arab Emirates, Uruguay, Vietnam

USA & Mexico HALFEN USA Inc.8521 F.M. 1976Converse, TX 78109

Phone: +1 800.423.9140E-Mail: [email protected]: www.halfenusa.com

Fax: +1 888.277.1695

Fax: +86 - 10 5907 3218

Canada

China

UCC Industries International (Distributor)Units 12 & 13895 Sandy Beach Road

Pickering, Ontario, L1W 3N7Provinces of British Columbia and Alberta: Please contact HALFEN USA Inc.

HALFEN Construction Accessories Distribution Co.Ltd.Room 601 Tower D, Vantone CentreNo.A6 Chao Yang Men Wai StreetChaoyang DistrictBeijing P.R. China 100020

Phone: +1 905.831.7724E-Mail: [email protected]: www.ucci.ca

Phone: +86 - 10 5907 3200E-Mail: [email protected]: www.halfen.cn

Fax: +1 905.831.5872

Fax: +91 22.4202.4001

Fax: +49 2173 970-123

India

Germany

CRH India Management Services Pvt. Ltd.73-C, 3 North Avenue, Maker Maxity,Bandra-Kurla Complex, Bandra (East),Mumbai 400 051

HALFEN GmbHLiebigstrasse 1440764 Langenfeld

Phone: +91 22.4202.4000E-Mail: [email protected]: www.halfen.in

Phone: +49 2173 970-0E-Mail: [email protected]: www.halfen.de

Documents

pg-us