Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
1
"OPEJ[FE�"MVNJOVN�(BUFT�EJSFDUMZ�GSPN�+"1"/��,VOLFM8PSLT �)POPMVMV �)*�������t��������������t�KBQBOFTFHBUFT�DPN
Measurements in Millimeters
Parts travel inside panel. Open bottom panel cap to find small items.
Post Type
HingeGA914 (single)
GA5915 (double)
Washer GA0799
Bolt M6x20
Instructions GD-Z37B
Outside Post/Hinge Post
Lock-side Post
Gate TypeSingle Double Hardware Single Double
Double Gate Single Gate
Top Hinge Bottom Hinge
To reverse the direction of the swing, remove bottom screw to release Shaft. Turn around hinge 180º. Reattach shaft.
Default Position
Attach hinges at pre-drilled locations only!
WasherBottom Hinge
Hinge-side Post
Lock-side Post
Post Installation
Reversing Direction of the Swing
1BDLBHJOH�-JTU
NOTE: Japa-nese customers like the panel 20mm lower than the posts. If you want to have Post and Panel flush on top, reduce post height by 20mm to H+80 =1480mm
Panel Height (H) is
1400mm
Panel Width (W) is
1000mm
6/11/18
2
"OPEJ[FE�"MVNJOVN�(BUFT�EJSFDUMZ�GSPN�+"1"/��,VOLFM8PSLT �)POPMVMV �)*�������t��������������t�KBQBOFTFHBUFT�DPN
House
House
StreetStreet
Double GateSingle Gate
Hinges are reversible. Decide on what side the hinges should before setting the posts.
House
Street
House
Street
Gate is factory-set to swing “in.” If you need to swing “out”, request Outward-Opening Hinge Attachments DPSHM. See more details on page 3 of the Handle Installation Manual.
Excavate for concrete footings. 300mm x 300mm / 12” x 12”
Post Installation
Reversing Direction
Measurements in Millimeters
LEFT - RIGHT
The Hinge space can be adjusted in 3 directions. Adjust UP - DOWN movement with the Panel-Hinge. LEFT - RIGHT and FORWARD - BACK is adjusted with the Post Hinge. Pre-drilled receiving holes have been reinforced inside the post. Therefore, do not modify hinge location on the post.
UP - DOWN
FORWARD - BACK
House
Hinges Adjust in 3 Directions
Lock-Screw
NOTE: Japanese customers like the panel 20mm lower than the posts. If you want to have Post and Panel flush on top, reduce post height by 20mm to H+80 =1480mm
6/11/18
Package List
Gate Panel
Panel Hinge GB5038
Hinge Cover GB5077
Hinge Back-Plate GA2919
Hinge Cap GA0056
Hinge Bolt
Panel Bottom Cap GB5031
Screws 4x12x9
Lock-Gap-Cover
Drill-ScrewNot needed for your Gate
Multi-panel-LeverNot needed for your Gate
Street Side
House Side
Street Side
House Side
Single Gate Double Gate
Parts travel inside panel. Open bottom panel cap to find small items.
Hinge Plate
Panel Hinge Loosely attach Panel
Hinge to Hinge-Plate and slide it into the panel groove, from the bottom.
Secure Bottom-cap with srewsPosition of Panel Hinges
Hinges travel inside the gate posts. Attach post hinges only at the pre-drilled locations.
House
Hinge Top Cap
Panel Hinge Screw
Rubber Washer
House
GATE PANEL Preparation 1
Notes for Set-upt��%PO�U�VTF�QBSUT�UIBU�EP�OPU�CFMPOH �EPO�U�NPEJGZt��5JHIUFO�BMM�CPMUTt��.BLF�TVSF�QBSUT�BSF�OPU�EBNBHFEt��.BLF�TVSF�BMM�QBSUT�NPWF�TNPPUIMZ
Attach the Panel Hinge Parts
Prepare the Hinges Measurements in Millimeters
Slide panel onto the Post Hinges from the top,
Panel Hinge
"OPEJ[FE�"MVNJOVN�(BUFT�EJSFDUMZ�GSPN�+"1"/��,VOLFM8PSLT �)POPMVMV �)*�������t��������������t�KBQBOFTFHBUFT�DPN
Measurements in Millimeters
Panel Height (H) is
1400mm
Panel Width (W) is
1000mm
6/11/18
Panel Hinge adjusts UP-DOWN
Post Hinge adjustsLEFT - RIGHT - AIN - OUT- B
t���5P�BEKVTU�)JOHFT �MPPTFO�CPMUT�UP�move hinge.
t���(BQ�PO�CPUUPN�TIPVME�CF�BCPVU�80mm.
t���"ęFS�BEKVTUNFOU �UJHIUFO�CPMUT�and screws firmly.
t���(BQ�CFUXFFO�QPTU�BOE�QBOFM� should be about 10mm
"ęFS�ZPV�MPDLFE�EPXO�ĕOBM�QPTJ-tion of hinges, snap plastic covers provided in place.
The Lock-down-stick is alreadyinstalled. In resting position, it sits in the panel. To employ it, use pinch-lock-mechanizm to move it up and down.
Lock-Down CupDecide on a location where the open panel will be secured down. Drill a hole and epoxy glue the receiving cup into hole. Max height is 125mm.
Screw on Lock-Gap-Cover with screws provided.
Street
Adjustment Screw B
Attachment Screw A
Hinge Adjustments 2
Securing Gate Panel in Open Position
"OPEJ[FE�"MVNJOVN�(BUFT�EJSFDUMZ�GSPN�+"1"/��,VOLFM8PSLT �)POPMVMV �)*�������t��������������t�KBQBOFTFHBUFT�DPN
Lock-Gap-Cover (only needed on Double Gates)
Lock-Gap-Cover attaches to the Secondary Panel.It hides the gap and prevents the Main Panel from swinging in the wrong direc-tion.
Secondary Panel
Pinch-Lock-Mechanizm
Measurements in Millimeters
"EKVTUNFOU�Directions UP-DOWNLEFT-RIGHTIN-OUT
This Lock-down-stick Handle is not needed for your gate.
(Only for triple and quadruple panel gates.)
6/11/18
"OPEJ[FE�"MVNJOVN�(BUFT�EJSFDUMZ�GSPN�+"1"/��,VOLFM8PSLT �)POPMVMV �)*�������t��������������t�KBQBOFTFHBUFT�DPN
Measurements in Millimeters
Hinge Hider Location
Post-side Hing Hider.A Double Gate has Hinge Hiders on both Posts.
Between the Panels sits the Lock-Gap-Hider. Find in-structions on the Gate Panel Manual page 2.
The Hinge Hiders (HH) are the last items to install. They attach to the posts in front of the panel. Align the HH-Bracket with the top of the panel. The screw location lies 60mm from the inside edge of the post (see grooves.) Attach HH-Bracket with screws provided.
Hinge Hider AttachmentPush the Hinge-Hider-Cover onto the HH-Bracket with a flat object and a mallet. Be sure you have the right location. Hinge-Hiders can not be re-positioned! Once fastened, they are very hard to remove.
Gate Panel Top of Panel
60mm
House Side
StreetHH Bracket
Screw Location
Screw Location
Hinge-Hider-Cover
Flat Object
wMallet
Street
House Side
Hinge Hider
Lock Hider
Hinge Hider
Hinge and Lock-Hiders are shipped inside the
posts.
WHinge and Lock Hiders - Double Gate
HH Bracket
6/11/18
M5 ×12
皿M4 ×8
皿M4 ×17
M5 ×12 皿M4 ×8
M4 ×17
M5 ×12
皿M4 ×8
皿M4 ×17
M5 ×12 皿M4 ×8
M4 ×17
HOUSE
M5 ×12
皿M4 ×8
皿M4 ×17
M5 ×12 皿M4 ×8
M4 ×17
M5 ×12
皿M4 ×8
皿M4 ×17
M5 ×12 皿M4 ×8
M4 ×17
HOUSE
HOUSE
HOUSE
Notes for Set-upt��%PO�U�VTF�QBSUT�UIBU�EP�OPU�CFMPOH �EPO�U�NPEJGZt��5JHIUFO�BMM�CPMUTt��.BLF�TVSF�QBSUT�BSF�OPU�EBNBHFEt��.BLF�TVSF�BMM�QBSUT�NPWF�TNPPUIMZGlossary:Main Panel�IPVTFT�UIF�MPDL�TFU�BOE�LFZ�DZMJOEFS���*U�JT�UIF�QBOFM�UIBU�NPWFT�ĕSTU�Secondary Panel�JT�UIF�QBOFM�UIBU�JT�VTVBMMZ�TUBUJPOBSZ ��CVU�DBO�CF�PQFOFE�CZ�SFUSBDUJOH�UIF�MPDL�EPXO�TUJDL��JOUP�UIF�QBOFM�
IMPORTANT:��.BLF�TVSF�UIF�LFZ�JT�OPU�JO�UIF�MPDL�XIFO�JOTUBMMJOH�UIF�IBOEMF��*U�DPVME�EBNBHF�UIF�NFDIBOJTN�
Reversible HandlećF�IBOEMF�DPNFT�GBDUPSZ�TFU�XJUI�LFZ�PO�UIF�SJHIU�QBOFM�GPS�PQFOJOH�JOXBSE�BOE�UP�UIF�SJHIU���:PV�DBO�IBWF�UIF�LFZ�PO�UIF�MFę�QBOFM�BOE�TXJOH�UP�MFę �CZ�UVSOJOH�UIF�IBOEMF������BOE�SFWFSTJOH�UIF�TUSJLFS�JOTJEF�UIF�MPDL�TFU��4FF�QBHF���
Opening IN - to the RIGHT (as s seen from Outside)ćF�IBOEMF�IBT�CFFO�TFU�JO�GBDUPSZ�UP�TJU�PO�UIF�SJHIU�QBOFM��1VU�BMM�QBSUT�UPHFUIFS�XJUI�TDSFXT�QSP�WJEFE��'PMMPX�TIPQ�ESBXJOHT�
Gate functions are usually described as seen from the OUTSIDE! #FMPX�EJBHSBN�TIPXT�UIF�JOTJEF�WJFX�CFDBVTF�UIF�NBJO�IBOEMF�QBSUT�BUUBDI�UP�UIF�JOTJEF�
Opening IN - to the LEFT (as s seen from Outside)
Main Handle Outside
Secondary Handle Inside
Gate Panel Stopper
Lock Panel Plate
NOTE: Your gate does not have a thumb-turn but a key on the inside.
4FF�BCPWF�SJHIU�TFDUJPO�PO�SFWFSTJOH�UIF�)BOEMF�
Secondary Panel Outside
Main Inside
Lock Panel Plate
Gate Panel Stopper
Outward Opening To make this gate opening outward see page 3.
)BOEMF�*OTUBMMBUJPO���DOUBLE GATE W
"OPEJ[FE�"MVNJOVN�(BUFT�EJSFDUMZ�GSPN�+"1"/��,VOLFM8PSLT �)POPMVMV �)*�������t��������������t�KBQBOFTFHBUFT�DPN
Attach Panel Stopper to Secondary Panel. It prevents the panel from swinging in the
wrong direction.
See Page 3
6/11/18
Secondary Panel Inside