raspored predavanja na TM I

Embed Size (px)

Citation preview

  • 8/7/2019 raspored predavanja na TM I

    1/2

    Y Daily Schedule - Clinac Technical Maintenance I Hi

    Monday

    Section Description Start Time End TimeLecture - Staff Introductions, Course Objectives, Orientation. 08:30 am 09:00 am

    Break 10:00 am 10:15 am

    Lecture (cont.), Block Diagram Overview 10:15 am 11:45 am

    Lunch 11:45 am 1:15 pm

    Lecture - Safety & Documentation Data Book, Data Book String Diagrams 1:15 pm 2:45 pm

    Break 2:45 pm 3:00 pm

    Lab Orientation Component ID Functional Operation 3:00 pm 4:30 pm

    Tuesday

    Section Description Start Time End TimeLecture - Machine Physics, Accelerator Theory, Beam Production, Bend Magnet 08:30 am 10:00 am

    Break 10:00 am 10:15 am

    Lecture - Beam Geometry Definitions, Specification Scans, Diagnostic Scans 10:15 am 11:45 am

    Lunch 11:45 am 1:15 pm

    Lecture - Power Distribution, Primary Power, Auxiliary Power 1:15 pm 2:45 pm

    Break 2:45 pm 3:00 pmLab - Service Mode I Setup, Interlocks, Motors, Display Menus 3:00 pm 4:30 pm

    Wednesday

    Section Description Start Time End TimeLab - Modulator High Voltage PS, Charge Cycle, Discharge Cycle, Support Circuits, Fault Detection 08:30 am 10:00 am

    Break 10:00 am 10:15 am

    Lecture (cont.) 10:15 am 11:45 am

    Lunch 11:45 am 1:15 pm

    Lecture - Control System I, System Architecture, Safety Features Interlocks 1:15 pm 2:45 pm

    Break 2:45 pm 3:00 pm

    Lab - Service Mode II Triggers, Lights, Calibration Menus, PRO Calibration 3:00 pm 4:30 pm

    Thursday

    Section Description Start Time End TimeLecture - RF System, Waveguide Theory, Block Diagram, Klystron Theory, AFC System Theory, Block Diagram

    3-dB Quadrature, Hybrid, Support Circuits08:30 am 10:00 am

    Break 10:00 am 10:15 am

    Lecture (cont.) 10:15 am 11:45 am

    Lunch 11:45 am 1:15 pm

    Lecture - Control System II, Digital Signal Interfacing 1:15 pm 2:45 pm

    Break 2:45 pm 3:00 pm

    Lab - Modulator & RF Systems 3:00 pm 4:30 pm

    Friday

    Section Description Start Time End TimeLecture - Control System III, Analog Signal Interfacing, Motor Interface, Meter Interface Board, SCI and DSYNC

    Boards08:30 am 10:00 am

    Break 10:00 am 10:15 am

    Lab - Service Mode III Utilities, Menu Hex Window Display, Communications Mode Event Log Analysis 10:15 am 11:45 am

  • 8/7/2019 raspored predavanja na TM I

    2/2

    Week 2

    Monday

    Section Description Start Time End TimeLecture - Electron Gun Theory, Construction, Load Line, Injection Voltage & Timing, Dose Rate Control 08:30 am 10:00 am

    Break 10:00 am 10:15 am

    Lecture - Gun Driver 10:15 am 11:45 am

    Lunch 11:45 am 1:15 pm

    Lecture - Energy Mode Selection BCD Codes, Mode Motions, Logic Interface Board 1:15 pm 2:45 pmBreak 2:45 pm 3:00 pm

    Lab - Peripherals, Couch Side, Panels, Pendants, Dedicated Keyboard 3:00 pm 4:30 pm

    Tuesday

    Section Description Start Time End TimeLecture - Auxiliary Electronics, Motor & Steering Control, Mode Motion Control 08:30 am 10:00 am

    Break 10:00 am 10:15 am

    Lecture (cont.) 10:15 am 11:45 am

    Lunch 11:45 am 1:15 pm

    Lecture - Support Systems Water, Dielectric Gas,Air 1:15 pm 2:45 pm

    Break 2:45 pm 3:00 pm

    Lab - Gun Waveforms, Mode Motions 3:00 pm 4:30 pm

    Wednesday

    Section Description Start Time End TimeLecture - Basic Vacuum System Theory, Vacion Power Supply 01:15 am 2:45 pm

    Lecture - Analog Dosimetry System, Ion Chamber Theory, Block Diagrams, Program Boards, Integrators &

    Servos, CAL/CHECK Cycle, I/L EXQ Board PFN Servo08:30 am 10:00 am

    Break 10:00 am 10:15 am

    Lecture (cont.) 10:15 am 11:45 am

    Lunch 11:45 am 01:15 am

    Break 2:45 pm 3:00 pm

    Lab - Dosimetry Alignment 3:00 pm 4:30 pm

    Thursday

    Section Description Start Time End TimeLecture - Control System IV, Control Timer & I/F Boards, Digital Dosimetry, Trigger Generation, Dose Rate,

    Control Signal Interfacing, Beam Control08:30 am 10:00 am

    Break 10:00 am 10:15 am

    Lecture (cont.) 10:15 am 11:45 am

    Lunch 11:45 am 1:15 pm

    Lecture - Accessories Gantry Display 1:15 pm 2:45 pm

    Break 2:45 pm 3:00 pm

    Lab - Troubleshooting 3:00 pm 4:30 pm

    Factory Tour and Course Dinner 6:00 pm 8:00 pm

    Friday

    Section Description Start Time End TimeLab - PMI/Preventive Maintenance Inspection 08:30 am 10:00 am

    Break 10:00 am 10:15 am

    Lecture - Review, Course Evaluation, Graduation! 10:15 am 11:45 am