router config.txt

7/29/2019 router config.txt

http://slidepdf.com/reader/full/router-configtxt 1/7

router 1

Router>enRouter#config tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname amityamity(config)#interface fa0/0amity(config-if)#ip address 192.168.2.1 255.255.255.0amity(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upamity(config-if)#interface serial2/0amity(config-if)#ip address 192.168.1.1 255.255.255.0amity(config-if)#clock rate 64000amity(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to downamity(config-if)#

System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)

Copyright (c) 2000 by cisco Systems, Inc.PT 1001 (PTSC2005) processor (revision 0x200) with 60416K/5120K bytes of memory

Self decompressing the image :########################################################################## [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government issubject to restrictions as set forth in subparagraph(c) of the Commercial Computer Software - RestrictedRights clause at FAR sec. 52.227-19 and subparagraph(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.170 West Tasman DriveSan Jose, California 95134-1706

Cisco Internetwork Operating System SoftwareIOS (tm) PT1000 Software (PT1000-I-M), Version 12.2(28), RELEASE SOFTWARE (fc5)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2005 by cisco Systems, Inc.Compiled Wed 27-Apr-04 19:01 by miwang

PT 1001 (PTSC2005) processor (revision 0x200) with 60416K/5120K bytes of memory.Processor board ID PT0123 (0123)PT2005 processor: part number 0, mask 01Bridging software.X.25 software, Version 3.0.0.4 FastEthernet/IEEE 802.3 interface(s)2 Low-speed serial(sync/async) network interface(s)32K bytes of non-volatile configuration memory.



16384K bytes of processor board System flash (Read/Write)

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>config t^

% Invalid input detected at '^' marker.

Router>config t^


Router>enRouter#config tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname amity2

amity2(config)#interface fa0/0amity2(config-if)#ip address 192.168.3.1% Incomplete command.amity2(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upamity2(config-if)#interface serial3/0amity2(config-if)#ip address 192.168.1.2 255.255.255.0amity2(config-if)#clock rate 64000amity2(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to upamity2(config-if)#ip address 192.168.3.1amity2(config-if)#interface fa0/0amity2(config-if)#ip address 192.168.3.1 255.255.255.0amity2(config-if)#no shutamity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet0/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet1/0amity2(config-if)#amity2(config-if)#exit

amity2(config)#interface Serial2/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface Serial3/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet0/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet1/0



amity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet0/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface Serial2/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface Serial3/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface Serial2/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface Serial3/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet0/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet1/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet0/0

amity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet0/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet1/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet0/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface Serial3/0amity2(config-if)#

amity2(config-if)#exitamity2(config)#interface FastEthernet0/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet1/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet0/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface Serial3/0amity2(config-if)#amity2(config-if)#exit

amity2(config)#interface FastEthernet0/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet0/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet4/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet0/0



amity2(config-if)#amity2(config-if)#exitamity2(config)#interface Serial3/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface FastEthernet0/0amity2(config-if)#amity2(config-if)#exitamity2(config)#interface Serial3/0amity2(config-if)#^Z%SYS-5-CONFIG_I: Configured from console by consoleamity2#show ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter areaN1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGPi - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area* - candidate default, U - per-user static route, o - ODRP - periodic downloaded static route

Gateway of last resort is not set

C 192.168.1.0/24 is directly connected, Serial3/0C 192.168.3.0/24 is directly connected, FastEthernet0/0

amity2#config tEnter configuration commands, one per line. End with CNTL/Z.amity2(config)#network 192.168.1.0

^% Invalid input detected at '^' marker.

amity2(config)#rip^


amity2(config)#router ripamity2(config-router)#network 192.168.1.0amity2(config-router)#network 192.168.2.0

amity2(config-router)#exitamity2(config)#router ripamity2(config-router)#network 192.168.1.0amity2(config-router)#network 192.168.3.0amity2(config-router)#exit

System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)Copyright (c) 2000 by cisco Systems, Inc.PT 1001 (PTSC2005) processor (revision 0x200) with 60416K/5120K bytes of memory

Self decompressing the image :########################################################################## [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government issubject to restrictions as set forth in subparagraph(c) of the Commercial Computer Software - RestrictedRights clause at FAR sec. 52.227-19 and subparagraph(c) (1) (ii) of the Rights in Technical Data and Computer



Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.170 West Tasman DriveSan Jose, California 95134-1706

Cisco Internetwork Operating System SoftwareIOS (tm) PT1000 Software (PT1000-I-M), Version 12.2(28), RELEASE SOFTWARE (fc5)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2005 by cisco Systems, Inc.Compiled Wed 27-Apr-04 19:01 by miwang

PT 1001 (PTSC2005) processor (revision 0x200) with 60416K/5120K bytes of memory.Processor board ID PT0123 (0123)PT2005 processor: part number 0, mask 01Bridging software.X.25 software, Version 3.0.0.4 FastEthernet/IEEE 802.3 interface(s)2 Low-speed serial(sync/async) network interface(s)32K bytes of non-volatile configuration memory.16384K bytes of processor board System flash (Read/Write)

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>enRouter#config t

Enter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname amityamity(config)#interface fa0/0amity(config-if)#192.168.2.1ip address 255.255.255.0amity(config-if)#no shout

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upamity(config-if)#interface sreerial2/0amity(config-if)#ip address 192.168.1.1 255.255.255.0amity(config-if)#clock rate 64000amity(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to downamity(config-if)#%SYS-5-CONFIG_I: Configured from console by consoleamity#%LINK-5-CHANGED: Interface Serial2/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up



amity con0 is now available

Press RETURN to get started.

amity>enableamity#configure terminalEnter configuration commands, one per line. End with CNTL/Z.amity(config)#interface FastEthernet0/0amity(config-if)#amity(config-if)#exitamity(config)#interface Serial2/0amity(config-if)#amity(config-if)#exitamity(config)#interface Serial3/0amity(config-if)#

amity(config-if)#exitamity(config)#interface FastEthernet5/0amity(config-if)#^Z%SYS-5-CONFIG_I: Configured from console by consoleamity#routTranslating "rout"...domain server (255.255.255.255)% Unknown command or computer name, or unable to find computer address

amity#ip route^


amity#^Z

amity#show ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter areaN1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGPi - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area* - candidate default, U - per-user static route, o - ODRP - periodic downloaded static route

Gateway of last resort is not set



C 192.168.1.0/24 is directly connected, Serial2/0C 192.168.2.0/24 is directly connected, FastEthernet0/0amity#router rip

^% Invalid input detected at '^' marker.

amity#config tEnter configuration commands, one per line. End with CNTL/Z.amity(config)#router ripamity(config-router)#network 192.168.1.0amity(config-router)#network 192.168.2.0amity(config-router)#exitamity(config)#amity(config)#interface FastEthernet0/0amity(config-if)#amity(config-if)#exitamity(config)#interface Serial2/0amity(config-if)#amity(config-if)#exitamity(config)#interface FastEthernet0/0amity(config-if)#amity(config-if)#exitamity(config)#interface Serial2/0

amity(config-if)#amity(config-if)#exitamity(config)#interface Serial2/0amity(config-if)#amity(config-if)#exitamity(config)#interface FastEthernet0/0amity(config-if)#amity(config-if)#exitamity(config)#interface Serial2/0amity(config-if)#amity(config-if)#exitamity(config)#interface FastEthernet0/0amity(config-if)#exit

Documents

router config.txt