Upload
lyphuc
View
213
Download
1
Embed Size (px)
Citation preview
Page 1 / 8www.baumer.com
LFFSdétecteur de niveau
FR/1
6101
2
Des
sins
et c
arac
téris
tique
s so
us ré
serv
e de
mod
ifica
tion
sans
pré
avis
Fiche technique LFFS-1
Avantages particuliers�� Parties en contact avec le fluide en acier inoxydable résistant aux acides et en PEEK�� Design hygiénique, compact, compatible avec les aliments�� Connexions hygiéniques conformes aux normes 3A, aux exigences de la FDA et aux directives de l’EHEDG�� Point de commutation précis sans étalonnage�� Température de processus -40...200 °C
�� Mesure de fluides avec des valeurs DK >1,5 (DK = directrice constant)�� Insensible à la mousse�� Témoin de commutation LED�� Sans maintenance�� Adapté à la détection de la séparation des milieux�� Configurable par FlexProgrammer 9701�� Autorisation ATEX pour gaz et poussièreR
74 - 03
Page 1 Design and specifications subject to change without notice
Data Sheet LFFS-1www.baumer.com/process
Description
Wetted parts in acid-proof, stainless steel and PEEK
Compact, food compatible, hygienic design
Hygienic connections conform to 3-A standards, FDA demands and EHEDG guidelines
Precise switching point without calibration
Process temperature -40...200°C
Measures media with DK-values >1.5
Not influenced by foam
LED switch indicator
Maintenance free
Suitable for media separation measurement
Configurable by FlexProgrammer 9701
ATEX approval for gas and dust
Level Switch LFFS
The Level Switch LFFS designed to detect levels in tanks, media separation and provide empty-pipe detection or dry-run protection for pumps.
A high frequency sweep signal is radiated from the sensor tip into the tank. The media will act as a virtual capacitor, which together with a coil in the sensor head, will form a circuit creating the switch point signal. This virtual capacity will depend of the di-electric value of the media. By means of the FlexProgrammer 9701 the output can be config-ured to either NPN, PNP or digital output signal. A damping of the output signal can be activated in case of a fluctuating media level, e.g. during tank filling.
The measurement is precise and unaffected by the mounting position in the tank. In the Flex-software a compensation for foam, bubbles and condensate as well as viscous media can be set.
The Flex-software also features an adjustment facility making the user able to adjust the sensor to a specific media.
The Level Switch LFFS measures liquids such as water and beer as well as viscous, sticky fluids, such as honey, youghurt, toothpaste and ketchup. Even dry medias can be measured, eg. sugar or flour.
The Level Switch LFFS is resistent against CIP and SIP agents.
Hygienic installation is also possible with the comprehensive range of accessories, see the overview at page 6.
Données techniques
CapteurSignal émis 100...180 MHZRaccord process Hygiénique : G1/2, 3A/DN38 ou raccord
coulissanteAdaptateurs Se reporter à la page 5Matériau isolant PEEK NaturaDonnées mécaniques
Boîtier Acier inoxydable, W1.4301/AISI 304Raccord process Acier inoxydable, W1.4404/AISI 316 LTemp. ambiante 40...85 °CTemp. de processus Norme & 3A/DN38 Raccord coulissant < 1 heure, Tamb < 60 °C
40...115 °C (voir courbe 1) 40...200 °C (voir courbe 1) -40...140 °C
Classe de protection IP67 (IEC 529)Pression du fluide Raccord coulissant : max. 16 bar
Norme & 3A/DN38 : max. 40 barVibrations CEI 6006826, GL test2Installation Toute positionRaccordements électriques
Presseétoupe M16 Plastique ou laiton nickeléConnecteur M12 Laiton nickelé ou acier inoxydable
AISI 304Autres données électriques
Alimentation 12,5...36 V CC, 35 mA max.Amortissement 0...10 sec.Temps de mise sous tension
<2 sec.
Hystérésis ± 1 mmReproductibilité ± 1 mmTemps de réaction 0.1 sec. (100 mS)
Approvals/conformitiesAutorisations/conformités EN 50155 Railway, 3A, EHEDG, FDA Normes 3A (norme & 3A/DN38)Mise au rebut du produit et de l’emballage
Selon les lois nationales en vigueur ou par retour chez Baumer.Données CEM
Immunité EN 61326Émission EN 61326Données Ex (ia)
Inductivité interne Li –< 10 μHCapacité interne Ci –< 33 nFDonnées de barrière U –< 30 VCC ; I –< 0.1 A ; P –< 0.75 WAutorisation Ex ia IIC T5, ATEX II 1G (voir tableau 1)
Plage d'alimentation 24...30 V CCClasse de température T1...T5 : 40 < Tamb < 85 °CAutorisation Ex tD A20 IP67 T100 °C, ATEX II 1D (voir tableau 1)
Plage d'alimentation 12,5...30 V CCClasse de température T100 °C : 40 < Tamb < 85 °CAutorisation Ex nA II T5, ATEX II 3G (voir tableau 1)
Plage d'alimentation 12,5...30 V CCClasse de température T1...T5 : 40 < Tamb < 85 °CSortie
Sortie (active) Max. 50 mA, protection contre les courtscircuits et températures élevées
Type de sortie Sortie PNP, NPN ou numérique (Pushpull)Polarité de sortie Voir dessinActif « bas » Sortie NPN et numérique
(V CC +2,5V) ± 0,5 V ; Rload 1 kOhmActif « haut » Sortie PNP et numérique
(V CC 2,5V) ± 0,5 V ; Rload 1 kOhmSortie à trois états ± 100 μA max.
AUDIN - 8, avenue de la malle - 51370 Saint Brice Courcelles - Tel : 03.26.04.20.21 - Fax : 03.26.04.28.20 - Web : http: www.audin.fr - Email : [email protected]
Page 2 / 8www.baumer.com
FR/1
6101
2
Des
sins
et c
arac
téris
tique
s so
us ré
serv
e de
mod
ifica
tion
sans
pré
avis
Fiche technique LFFS-1
LFFSDétecteur de niveau
Dessins cotés
Page 2 Design and specifications subject to change without notice
Data Sheet LFFS-1www.baumer.com/process
Technical Data
SensorRadiated signal 100...180 MHZ
Process connection Hygienic: G1/2, 3A/DN38 or sliding connection
Adapters Refer to page 6
Insulating material PEEK Natura
Mechanical dataHousing Stainless Steel, W1.4301/AISI 304
Process connection Stainless Steel, W1.4404/AISI 316 L
Amb. temperature -40...85°C
Process temperature
Sliding connection -40...200°C (See curve 1)
Std. & 3A/DN38 -40...115°C (See curve 1)
< 1 hour, Tamb < 60°C -40...140°C
Protection class IP67 (IEC 529)
Media pressure Sliding connection: Max. 16 bar Std. & 3A/DN38: Max. 40 bar
Vibrations IEC 60068-2-6, GL test2
Installation Any position
Conformity 3-A standards (Std. & 3A/DN38)
Electrical connectionCable gland M16 Plast or Nickel-plated brass
Plug M12 Nickel-plated brass
Other electrical dataPower supply 12,5...36 VDC, 35 mA max.
Damping 0...10 sec.
Power-up time <2 sec.
Hysteresis ± 1 mm
Repeatability ± 1 mm
Reaction time 0.1 sec. max.
Dimensional Drawings[mm]
Disposal of product and packingAccording to national laws or by returning to Baumer
EMC dataImmunity EN 61326
Emission EN 61326
Ex data (ia)Internal inductivity Li < 10 µH
Internal capacity Ci < 33 nF
Barrier data U < 30 VDC ; I < 0.1 A ; P < 0.75 W
Approval Ex ia IIC T5, ATEX II 1G (See table 1)Supply range 24...30 VDC
Temperature class T1...T5: -40 < Tamb < 85°C
Approval Ex tD A20 IP67 T100°C, ATEX II 1D (See table 1)Supply range 12,5...30 VDC
Temperature class T100°C: -40 < Tamb < 85°C
Approval Ex nA II T5, ATEX II 3G (See table 1)Supply range 12,5...30 VDC
Temperature class T1...T5: -40 < Tamb < 85°C
OutputOutput (active) Max. 50 mA, short-circuit and
high-temperature protected
Output type PNP, NPN or Digital output (Push-pull)
Output polarity See drawing
Active “Low” NPN and Digital output (-VDC +2.5V) ± 0.5V ; Rload 1 kOhm
Active “High” PNP and Digital output (VDC -2.5V) ± 0.5V ; Rload 1 kOhm
Three State Output ± 100µA Max.
Factory SettingsOutput PNP
Measure DK value > 2
Damping 0.1 sec.
58
44
18
M16 gland M12 plug
AF22
G1/2
G1/2 Hygienic connection
ø55
Safety chain
G1/2 Hygienic sliding nipple
Sliding connection length,refer to ordering data
G1/2 Hygienic, Sliding connection
3A/DN38 Hygienic connectionO-ring EPDM incl.
31.5
19
Washer ring kit, 2 items Type no. 4401 8001included
Données techniques
Réglages d’usineSortie PNP, PNP ou numériqueMesure Valeur DK 1,5Amortissement 0,1 sec.
Raccordements électriques
Page 3 Design and specifications subject to change without notice
Data Sheet LFFS-1www.baumer.com/process
Electrical Installation
12,5...36 VDC
LED
LED
+
-
0 mA
0 mA
50 mA
50 mA
PNP Output 50 mA max.
12,5...36 VDC+
-
12,5...36 VDC+
-12,5...36 VDC
+
-
Active High
PLC
NPN Output 50 mA max.
NPN Output 50 mA max.
12,5...36 VDC+
-
PNP Output 50 mA max.
Normally Open
Normally Closed
12,5...36 VDC
-
+
Active Low
PLC
Digital Output 50 mA max.
Digital Output 50 mA max.
Electrical Connection
2- or (+)
1
6
5
3
4
12,5...36 Vdc+ or (-)
Sensor
OutputTeach-in
Case
M12plug
1
4
2
3
M12 plug: 1: Brown 2: White 3: Blue 4: Black
Presseétoupe M16
Raccordement hygiénique
Capteur
SortieTeach-in
Raccordement hygiénique 3A/DN38Joint torique EPDM incl.
Chaîne de sécurité
Raccord coulissant hygiénique G1/2
Connecteur M12
Kit de rondelles, 2 piècesType réf. 401 8001 inclus
Raccord coulissant hygiénique G1/2
Longueur de raccord coulissant, se reporter aux données de commande
Boîtier
Connecteur M12
Connecteur M12: 1 : marron 2 : blanc 3 : bleu 4 : noir
AUDIN - 8, avenue de la malle - 51370 Saint Brice Courcelles - Tel : 03.26.04.20.21 - Fax : 03.26.04.28.20 - Web : http: www.audin.fr - Email : [email protected]
Page 3 / 8www.baumer.com
FR/1
6101
2
Des
sins
et c
arac
téris
tique
s so
us ré
serv
e de
mod
ifica
tion
sans
pré
avis
Fiche technique LFFS-1
LFFSDétecteur de niveau
Page 3 Design and specifications subject to change without notice
Data Sheet LFFS-1www.baumer.com/process
Electrical Installation
12,5...36 VDC
LED
LED
+
-
0 mA
0 mA
50 mA
50 mA
PNP Output 50 mA max.
12,5...36 VDC+
-
12,5...36 VDC+
-12,5...36 VDC
+
-
Active High
PLC
NPN Output 50 mA max.
NPN Output 50 mA max.
12,5...36 VDC+
-
PNP Output 50 mA max.
Normally Open
Normally Closed
12,5...36 VDC
-
+
Active Low
PLC
Digital Output 50 mA max.
Digital Output 50 mA max.
Electrical Connection
2- or (+)
1
6
5
3
4
12,5...36 Vdc+ or (-)
Sensor
OutputTeach-in
Case
M12plug
1
4
2
3
M12 plug: 1: Brown 2: White 3: Blue 4: Black
Page 3 Design and specifications subject to change without notice
Data Sheet LFFS-1www.baumer.com/process
Electrical Installation
12,5...36 VDC
LED
LED
+
-
0 mA
0 mA
50 mA
50 mA
PNP Output 50 mA max.
12,5...36 VDC+
-
12,5...36 VDC+
-12,5...36 VDC
+
-
Active High
PLC
NPN Output 50 mA max.
NPN Output 50 mA max.
12,5...36 VDC+
-
PNP Output 50 mA max.
Normally Open
Normally Closed
12,5...36 VDC
-
+
Active Low
PLC
Digital Output 50 mA max.
Digital Output 50 mA max.
Electrical Connection
2- or (+)
1
6
5
3
4
12,5...36 Vdc+ or (-)
Sensor
OutputTeach-in
Case
M12plug
1
4
2
3
M12 plug: 1: Brown 2: White 3: Blue 4: Black
Installation électriqueNormally Open
Normally Closed
Configuration Accessoires
FlexProgrammer 9701
Page 4 Design and specifications subject to change without notice
Data Sheet LFFS-1www.baumer.com/process
Safety 5´ digitStandard Ex ia IIC T5, ATEX II 1G (Gas) *Ex tD A20 IP67 T100°C, ATEX II 1D (Dust)Ex nA II T5, ATEX II 3G
Electrical Connection 6´ digitPlug, M12Cable gland, M16 brassCable gland, M16 Polyamid
Process Connection 7´ digitG1/2, PEEK tip {1}3A/DN38 Hygienic connection {1}G1/2, PEEK tip, sliding connection, 100 mm adjustable, incl. washer ring kit 4401 8001 {2}G1/2, PEEK tip, sliding connection, 250 mm adjustable, incl. washer ring kit 4401 8001 {2}
Configuration 8´ digitConfiguration according to customer specifications
Ordering Details - Level Switch LFFSLFFS xxx (c)
0 1 2 3
1 2 3
1 2 3 4
c
Note: Ambient temperature range 0...50°C
FlexProgrammer 9701
1
2
Red clip
Black clipThe FlexProgrammer 9701 is a dedicated tool to configure all Baumer configurable Flex-products.
Type No. 9701-0001 comprises: FlexProgrammerCable with 2 aligator clips Cable from FlexProgrammer to M12 plug for TE2 Cable from FlexProgrammer to M12 Plug for LFFS, LBFS, CPXUSB cableCD with the FlexProgram software
Disconnect the power supply before connecting the FlexProgrammer 9701 to the Level Switch LFFS
PEEK naturaAngle > 135 deg.
EPDM O-rings supplied with 3-A marked products are conform to Sanitary Standard Class II (8% milk fat max.)
EPDM gaskets supplied with 3-A marked products are conform to Sanitary Standard Class I (8% milk fat max.)
Refer to the 3-A marked counter parts in the data sheet “Accessories Universal”.
Level Switch LFFS, example
1
2
1
2
The washer ring kit for sliding connection, type no. 4401 8001 Can be ordered separately. Baumer recommended to replace this kit if deformed.
* Recommended isolating module: PROFSI3-B25100-ALG-LS
{1} The 3-A mark and the EHEDG certifcate is valid only when the product is mounted in a 3-A marked or EHEDG certified counter part and installed according to the installation manual. Use also a 3-A marked O-ring or gasket if relevant. The 3-A marked products conforms to the 3-A Sanitary Standard criteria. Materials and surfaces fulfill the FDA demands and are certified by EHEDG.
{2} Certified by EHEDG. Fulfills the FDA demand.
3A certificate / EHEDG certificate
Configuration Accessories
Page 4 Design and specifications subject to change without notice
Data Sheet LFFS-1www.baumer.com/process
Safety 5´ digitStandard Ex ia IIC T5, ATEX II 1G (Gas) *Ex tD A20 IP67 T100°C, ATEX II 1D (Dust)Ex nA II T5, ATEX II 3G
Electrical Connection 6´ digitPlug, M12Cable gland, M16 brassCable gland, M16 Polyamid
Process Connection 7´ digitG1/2, PEEK tip {1}3A/DN38 Hygienic connection {1}G1/2, PEEK tip, sliding connection, 100 mm adjustable, incl. washer ring kit 4401 8001 {2}G1/2, PEEK tip, sliding connection, 250 mm adjustable, incl. washer ring kit 4401 8001 {2}
Configuration 8´ digitConfiguration according to customer specifications
Ordering Details - Level Switch LFFSLFFS xxx (c)
0 1 2 3
1 2 3
1 2 3 4
c
Note: Ambient temperature range 0...50°C
FlexProgrammer 9701
1
2
Red clip
Black clipThe FlexProgrammer 9701 is a dedicated tool to configure all Baumer configurable Flex-products.
Type No. 9701-0001 comprises: FlexProgrammerCable with 2 aligator clips Cable from FlexProgrammer to M12 plug for TE2 Cable from FlexProgrammer to M12 Plug for LFFS, LBFS, CPXUSB cableCD with the FlexProgram software
Disconnect the power supply before connecting the FlexProgrammer 9701 to the Level Switch LFFS
PEEK naturaAngle > 135 deg.
EPDM O-rings supplied with 3-A marked products are conform to Sanitary Standard Class II (8% milk fat max.)
EPDM gaskets supplied with 3-A marked products are conform to Sanitary Standard Class I (8% milk fat max.)
Refer to the 3-A marked counter parts in the data sheet “Accessories Universal”.
Level Switch LFFS, example
1
2
1
2
The washer ring kit for sliding connection, type no. 4401 8001 Can be ordered separately. Baumer recommended to replace this kit if deformed.
* Recommended isolating module: PROFSI3-B25100-ALG-LS
{1} The 3-A mark and the EHEDG certifcate is valid only when the product is mounted in a 3-A marked or EHEDG certified counter part and installed according to the installation manual. Use also a 3-A marked O-ring or gasket if relevant. The 3-A marked products conforms to the 3-A Sanitary Standard criteria. Materials and surfaces fulfill the FDA demands and are certified by EHEDG.
{2} Certified by EHEDG. Fulfills the FDA demand.
3A certificate / EHEDG certificate
Configuration Accessories
Page 4 Design and specifications subject to change without notice
Data Sheet LFFS-1www.baumer.com/process
Safety 5´ digitStandard Ex ia IIC T5, ATEX II 1G (Gas) *Ex tD A20 IP67 T100°C, ATEX II 1D (Dust)Ex nA II T5, ATEX II 3G
Electrical Connection 6´ digitPlug, M12Cable gland, M16 brassCable gland, M16 Polyamid
Process Connection 7´ digitG1/2, PEEK tip {1}3A/DN38 Hygienic connection {1}G1/2, PEEK tip, sliding connection, 100 mm adjustable, incl. washer ring kit 4401 8001 {2}G1/2, PEEK tip, sliding connection, 250 mm adjustable, incl. washer ring kit 4401 8001 {2}
Configuration 8´ digitConfiguration according to customer specifications
Ordering Details - Level Switch LFFSLFFS xxx (c)
0 1 2 3
1 2 3
1 2 3 4
c
Note: Ambient temperature range 0...50°C
FlexProgrammer 9701
1
2
Red clip
Black clipThe FlexProgrammer 9701 is a dedicated tool to configure all Baumer configurable Flex-products.
Type No. 9701-0001 comprises: FlexProgrammerCable with 2 aligator clips Cable from FlexProgrammer to M12 plug for TE2 Cable from FlexProgrammer to M12 Plug for LFFS, LBFS, CPXUSB cableCD with the FlexProgram software
Disconnect the power supply before connecting the FlexProgrammer 9701 to the Level Switch LFFS
PEEK naturaAngle > 135 deg.
EPDM O-rings supplied with 3-A marked products are conform to Sanitary Standard Class II (8% milk fat max.)
EPDM gaskets supplied with 3-A marked products are conform to Sanitary Standard Class I (8% milk fat max.)
Refer to the 3-A marked counter parts in the data sheet “Accessories Universal”.
Level Switch LFFS, example
1
2
1
2
The washer ring kit for sliding connection, type no. 4401 8001 Can be ordered separately. Baumer recommended to replace this kit if deformed.
* Recommended isolating module: PROFSI3-B25100-ALG-LS
{1} The 3-A mark and the EHEDG certifcate is valid only when the product is mounted in a 3-A marked or EHEDG certified counter part and installed according to the installation manual. Use also a 3-A marked O-ring or gasket if relevant. The 3-A marked products conforms to the 3-A Sanitary Standard criteria. Materials and surfaces fulfill the FDA demands and are certified by EHEDG.
{2} Certified by EHEDG. Fulfills the FDA demand.
3A certificate / EHEDG certificate
Configuration Accessories
Page 4 Design and specifications subject to change without notice
Data Sheet LFFS-1www.baumer.com/process
Safety 5´ digitStandard Ex ia IIC T5, ATEX II 1G (Gas) *Ex tD A20 IP67 T100°C, ATEX II 1D (Dust)Ex nA II T5, ATEX II 3G
Electrical Connection 6´ digitPlug, M12Cable gland, M16 brassCable gland, M16 Polyamid
Process Connection 7´ digitG1/2, PEEK tip {1}3A/DN38 Hygienic connection {1}G1/2, PEEK tip, sliding connection, 100 mm adjustable, incl. washer ring kit 4401 8001 {2}G1/2, PEEK tip, sliding connection, 250 mm adjustable, incl. washer ring kit 4401 8001 {2}
Configuration 8´ digitConfiguration according to customer specifications
Ordering Details - Level Switch LFFSLFFS xxx (c)
0 1 2 3
1 2 3
1 2 3 4
c
Note: Ambient temperature range 0...50°C
FlexProgrammer 9701
1
2
Red clip
Black clipThe FlexProgrammer 9701 is a dedicated tool to configure all Baumer configurable Flex-products.
Type No. 9701-0001 comprises: FlexProgrammerCable with 2 aligator clips Cable from FlexProgrammer to M12 plug for TE2 Cable from FlexProgrammer to M12 Plug for LFFS, LBFS, CPXUSB cableCD with the FlexProgram software
Disconnect the power supply before connecting the FlexProgrammer 9701 to the Level Switch LFFS
PEEK naturaAngle > 135 deg.
EPDM O-rings supplied with 3-A marked products are conform to Sanitary Standard Class II (8% milk fat max.)
EPDM gaskets supplied with 3-A marked products are conform to Sanitary Standard Class I (8% milk fat max.)
Refer to the 3-A marked counter parts in the data sheet “Accessories Universal”.
Level Switch LFFS, example
1
2
1
2
The washer ring kit for sliding connection, type no. 4401 8001 Can be ordered separately. Baumer recommended to replace this kit if deformed.
* Recommended isolating module: PROFSI3-B25100-ALG-LS
{1} The 3-A mark and the EHEDG certifcate is valid only when the product is mounted in a 3-A marked or EHEDG certified counter part and installed according to the installation manual. Use also a 3-A marked O-ring or gasket if relevant. The 3-A marked products conforms to the 3-A Sanitary Standard criteria. Materials and surfaces fulfill the FDA demands and are certified by EHEDG.
{2} Certified by EHEDG. Fulfills the FDA demand.
3A certificate / EHEDG certificate
Configuration Accessories
Page 4 Design and specifications subject to change without notice
Data Sheet LFFS-1www.baumer.com/process
Safety 5´ digitStandard Ex ia IIC T5, ATEX II 1G (Gas) *Ex tD A20 IP67 T100°C, ATEX II 1D (Dust)Ex nA II T5, ATEX II 3G
Electrical Connection 6´ digitPlug, M12Cable gland, M16 brassCable gland, M16 Polyamid
Process Connection 7´ digitG1/2, PEEK tip {1}3A/DN38 Hygienic connection {1}G1/2, PEEK tip, sliding connection, 100 mm adjustable, incl. washer ring kit 4401 8001 {2}G1/2, PEEK tip, sliding connection, 250 mm adjustable, incl. washer ring kit 4401 8001 {2}
Configuration 8´ digitConfiguration according to customer specifications
Ordering Details - Level Switch LFFSLFFS xxx (c)
0 1 2 3
1 2 3
1 2 3 4
c
Note: Ambient temperature range 0...50°C
FlexProgrammer 9701
1
2
Red clip
Black clipThe FlexProgrammer 9701 is a dedicated tool to configure all Baumer configurable Flex-products.
Type No. 9701-0001 comprises: FlexProgrammerCable with 2 aligator clips Cable from FlexProgrammer to M12 plug for TE2 Cable from FlexProgrammer to M12 Plug for LFFS, LBFS, CPXUSB cableCD with the FlexProgram software
Disconnect the power supply before connecting the FlexProgrammer 9701 to the Level Switch LFFS
PEEK naturaAngle > 135 deg.
EPDM O-rings supplied with 3-A marked products are conform to Sanitary Standard Class II (8% milk fat max.)
EPDM gaskets supplied with 3-A marked products are conform to Sanitary Standard Class I (8% milk fat max.)
Refer to the 3-A marked counter parts in the data sheet “Accessories Universal”.
Level Switch LFFS, example
1
2
1
2
The washer ring kit for sliding connection, type no. 4401 8001 Can be ordered separately. Baumer recommended to replace this kit if deformed.
* Recommended isolating module: PROFSI3-B25100-ALG-LS
{1} The 3-A mark and the EHEDG certifcate is valid only when the product is mounted in a 3-A marked or EHEDG certified counter part and installed according to the installation manual. Use also a 3-A marked O-ring or gasket if relevant. The 3-A marked products conforms to the 3-A Sanitary Standard criteria. Materials and surfaces fulfill the FDA demands and are certified by EHEDG.
{2} Certified by EHEDG. Fulfills the FDA demand.
3A certificate / EHEDG certificate
Configuration Accessories
Baumer configurable Combiproducts
Contact à ouverture
Contact à fermeture
VCC
Sortie PNP 50 mA max.
Sortie PNP 50 mA max.
Clip rouge
Clip noir Remarque : Plage de température ambiante 0...50°C
Débrancher l’alimentation électrique avant de raccorder le FlexProgrammer 9701 au contacteur de niveau LFFS
Le FlexProgrammer 9701 est un outil dédié permettant de configurer tous les produits Combi configurables Baumer.
Le type réf. 9701-0001 comprend : FlexProgrammer CâblesCD avec logiciel FlexProgram
Sortie NPN 50 mA max.
Sortie NPN 50 mA max.
Sortie numérique 50 mA max.
Actif « haut »
Actif « bas »
Sortie numérique 50 mA max.
VCC
VCC
VCC
VCC
VCC
AUDIN - 8, avenue de la malle - 51370 Saint Brice Courcelles - Tel : 03.26.04.20.21 - Fax : 03.26.04.28.20 - Web : http: www.audin.fr - Email : [email protected]
Page 4 / 8www.baumer.com
FR/1
6101
2
Des
sins
et c
arac
téris
tique
s so
us ré
serv
e de
mod
ifica
tion
sans
pré
avis
Fiche technique LFFS-1
LFFSDétecteur de niveau
Le raccord coulissant (Figure 1)
Température du fluide par rapport à longueur extérieure du raccord coulissant (Courbe 1)
Le dessin illustre la façon dont le raccord coulissant peut être utilisé dans au minimum 4 applications :1) Installé au sommet d’un réservoir pour ajuster le niveau de
remplissage maximal.2) Servant de col de refroidissement dans les applications à haute
température.3) Ajusté pour placer la pointe du capteur à l’intérieur du réservoir.4) Pour atteindre le matériau isolant.
Il est capital que la température ambiante maximale pour les appareils électroniques ne soit jamais dépassée. Pour les produits approuvés par ATEX, merci de consulter le tableau 1.
Les conditions de travail pour le raccord coulissant à différentes tem-pératures de fluide ainsi que les températures ambiantes spécifiées sont indiquées dans la courbe 1.
Exemple, comment lire la Courbe 1 :Un raccord coulissant de 250 mm est installé dans un réservoir avec une longueur d’insertion totale de 150 mm. La longueur extérieure du raccord coulissant est donc de 250 150 = 100 mm.La température maximale du fluide sera de 160 °C.Lire l’axe X à 100 mm et l’axe Y à 160 °C et trouver que la tempé-rature ambiante doit être maintenue endeçà de 50 °C. Si la chaleur sortant du réservoir provoque une température ambiante plus élevée dans le boîtier, le dispositif d’isolation du réservoir doit alors être modi-fié pour être plus performant.
Kølehals for FLS Mikael Jensen / 2009-08-26
180183,33186,67
190,6193,93
197,5
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
210
30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250
Page 5 Design and specifications subject to change without notice
Data Sheet LFFS-1www.baumer.com/process
Media Temperature°C
The Sliding Connection (Figure 1)
The drawing shows how the sliding connection can be used for at least 4 applications: 1) Mounted at the top of a tank to adjust to a maximum level.2) Serving as a cooling neck in high media temperature applications.3) Adjusted to place the sensor tip deeper inside the tank.4) To reach in through insulation material.
It is essential that the max. ambience temperature for the electronics is never exceeded. For ATEX approved products please refer to table 1.
The working conditions for the sliding connection in different media temperatures and specified ambient temperatures can be found in curve 1.
Media Temperature versus External Length of Sliding Connection (Curve 1)
External length of sliding connection (mm) See figure 1
External length of sliding connection
Lumpy or sticky media
Insulation
1)
2)
3)
4)
Example, how to read Curve 1:A 250 mm sliding connection is mounted in a tank with a total insert length of 150 mm. Hence the external length of the sliding connection will be 250 - 150 = 100 mm. The media temperature will be max. 160 °C.Read the x-axis at 100 mm an the y-axis at 160°C and find that the ambient temperature must be kept below 50°C. In case the radiated heat from the tank will cause a higher ambient temperature at the housing efficient insulation of the tank must be established.
Tamb max. 40°C Tamb max. 60°C
Tamb max. 75°C
Tamb max. 85°C
NB: Std. + 3A/DN38 = 35 mm external length
Free external length of sliding connection see curve 1 below
Lumpy or sticky media
Insulation
1)
2)
3)
4)
Longueur externe libre de raccord coulissant voir courbe 1 ci-dessous
Fluide grumeleux ou collant
Température du fluide°C
Longueur extérieure du raccord coulissant (mm) Voir figure 1NB : Norme + 3A/DN38 = longueur extérieure 35 mm
Isolation
AUDIN - 8, avenue de la malle - 51370 Saint Brice Courcelles - Tel : 03.26.04.20.21 - Fax : 03.26.04.28.20 - Web : http: www.audin.fr - Email : [email protected]
Page 5 / 8www.baumer.com
FR/1
6101
2
Des
sins
et c
arac
téris
tique
s so
us ré
serv
e de
mod
ifica
tion
sans
pré
avis
Fiche technique LFFS-1
LFFSDétecteur de niveau
Accessoires - Présentation
R
74 - 03
R
74 - 03
R
74 - 03
R
74 - 03
R
74 - 03
R
74 - 03
Page 6 Design and specifications subject to change without notice
Data Sheet LFFS-1www.baumer.com/process
Accessories - Overview
CAM02x
LFFS-xx1
MAM02x-xxx PM02x
PM021
LAM020-1
VAM 02x
PM025
PM022-x
RAM020-2
RAM020-1
SAM020-051-1
Welding part 3A/DN38 hygienic 81 26-916
Please refer to the data sheet “FlexBar Accessories” for these accessories.
Please refer to the data sheet “Accessories Universal” for these accessories.
LFFS-xx3/4
LFFS-xx2
Welding part 3A/DN38 hygienic 81 26-928
CAM 023 PM023
VAM 023
Pièce à souder 3A/DN38 hygiénique 81 26916
Pièce à souder 3A/DN38 hygiénique 81 26928
AUDIN - 8, avenue de la malle - 51370 Saint Brice Courcelles - Tel : 03.26.04.20.21 - Fax : 03.26.04.28.20 - Web : http: www.audin.fr - Email : [email protected]
Page 6 / 8www.baumer.com
FR/1
6101
2
Des
sins
et c
arac
téris
tique
s so
us ré
serv
e de
mod
ifica
tion
sans
pré
avis
Fiche technique LFFS-1
LFFSDétecteur de niveau
Installation - Ex ia G
Installation - Ex tD
Installation - Ex ia G
Conditions de Ex-Certification (Table 1)Un détecteur de niveau LFFS1xx est approuvé Ex ia IIC T5, ATEX II 1G pour application dans des zones dangereuses conformément aux directives européennes en vigueur. Le produit doit être installé confor-mément aux directives applicables pour la zone 0 avec une barrière.
Un détecteur de niveau LFFS2xx est approuvé Ex tD A20 IP67 T100°C, ATEX II 1D pour application dans des zones dangereuses conformément aux directives européennes en vigueur. Le produit doit être installé conformément aux directives applicables pour la zone 20 sans barrière.
Un détecteur de niveau LFFS3xx est approuvé Ex nA II T5, ATEX II 3G pour application dans des zones dangereuses conformément aux directives européennes en vigueur. Le produit doit être installé confor-mément aux directives applicables pour la zone 2 sans barrière.
Type de connexion Tamb °C Temp. max. du fluide °C
Remarque
Norme & 3A/DN38 40...85 8540...60 95 {2}-40...40 115 {2}
Raccord coulissant 100 mm 40...85 8540...60 150 {2}-40...40 175 {2}
Raccord coulissant 250 mm 40...85 8540...60 195 {2}-40...40 200 {2} {3}
Remarque {2} : sachant que la pointe du capteur de l’instrument est la seule partie en contact avec le fluide.Remarque {3} : température de fluide maximum autorisée.
Données ExPlage d'alimentation 24...30 V CCClasse de température T1...T5: voir tableau Inductivité interne Li < 10 μHCapacité interne Ci < 33 nFDonnées de barrière U < 30 V CC ; I < 0.1 A ; P < 0.75 W
Installation - Ex ia IIC T5, ATEX II 1G
Un contacteur de niveau LFFS1xx est approuvé Ex ia IIC T5, ATEX II 1G pour application dans des zones dangereuses conformément aux directives européennes en vigueur.Le produit doit être installé conformément aux directives applicables pour la zone 0 avec une barrière.Une barrière certifiée Ex ia ou d’isolation avec des valeurs maximales de Umax = 30 V CC ; Imax = 0,1 A ; Pmax = 0,75 W doit être utilisée.
Page 8 Design and specifications subject to change without notice
Data Sheet LFFS-1www.baumer.com/process
Ex ia IIC T5, ATEX II 1G - InstallationA Level Switch LFFS-1xx is Ex ia IIC T5, ATEX II 1G approved for application in hasardous areas in accordance with the current EU-directives. The product must be installed in accordance with prevailing guidelines for zone 0 with a barrier.
Ex-dataSupply range 24...30 VDC
Temperature class T1...T5: See table 1
Internal inductivity Li < 10 µH
Internal capacity Ci < 33 nF
Barrier data U < 30 VDC ; I < 0.1 A ; P < 0.75 W
A certified Ex ia or isolation barrier with the maximum values Umax = 30 VDC ; Imax = 0.1 A ; Pmax = 0.75 W must be used.
22...120VDC or90...253 VAC
NO
COM
NC
PNP out
-
+
A
B
1
2
3
C
Safe area Zone 0/1
Level Switch LFFSIsolating Module PROFSI3-B25100-ALG-LS
NB: Only valid for PNP output
Barrière à isolation galvaniquePROFSI3-B25100-ALG-LS
NB : pour une sortie PNP, utiliser impérativement la barrière PROFSI3-B25100-ALG-LS.
Zone de sécurité
22...120 V CC ou 90...253 V CA
Sortie PNP
Détecteur de niveau LFFS
AUDIN - 8, avenue de la malle - 51370 Saint Brice Courcelles - Tel : 03.26.04.20.21 - Fax : 03.26.04.28.20 - Web : http: www.audin.fr - Email : [email protected]
Page 7 / 8www.baumer.com
FR/1
6101
2
Des
sins
et c
arac
téris
tique
s so
us ré
serv
e de
mod
ifica
tion
sans
pré
avis
Fiche technique LFFS-1
LFFSDétecteur de niveau
Données ExPlage d'alimentation 12,5...30 V CC, max. 100 mAClasse de température T100 : voir tableau 1
Données ExPlage d'alimentation 12,5...30 V CC, max. 0,1 AClasse de température T1...T5 : voir tableau 1
Installation - Ex tD A20 IP67 T100, ATEX II 1D
Installation - Ex nA II T5, ATEX II 3G
Un contacteur de niveau LFFS2xx est approuvé Ex tD A20 IP67 T100°C, ATEX II 1D pour application dans des zones dangereuses conformément aux directives européennes en vigueur. Le produit doit être installé conformément aux directives applicables pour la zone 20 sans barrière.
Un détecteur de niveau LFFS3xx est approuvé Ex nA II T5, ATEX II 3G pour application dans des zones dangereuses conformément aux directives européennes en vigueur. Le produit doit être installé confor-mément aux directives applicables pour la zone 2 sans barrière.
Page 9 Design and specifications subject to change without notice
Data Sheet LFFS-1www.baumer.com/process
A Level Switch LFFS-2xx is Ex tD A20 IP67 T100°C, ATEX II 1D approved for application in hasardous areas in accordance with the current EU-directives. The product must be installed in accordance with prevailing guidelines for zone 20 without a barrier.
Ex-dataSupply range 12,5...30 VDC, max 100 mA
Temperature class T100: See table 1
Ex nA II T5, ATEX II 3G - Installation
Level Switch LFFS
12,5..30 VDC
1 2
3
Remote Lamp
A Level Switch LFFS-3xx is Ex nA II T5, ATEX II 3G approved for application in hasardous areas in accordance with the current EU-directives. The product must be installed in accordance with prevailing guidelines for zone 2 without a barrier.
Ex-dataSupply range 12,5...30 VDC, Max. 0.1A
Temperature class T1...T5: See table 1
External lamp Level Switch LFFS
+
-
12,5...30 VDC
Ex tD A20 IP67 T100, ATEX II 1D - Installation
Out
Page 9 Design and specifications subject to change without notice
Data Sheet LFFS-1www.baumer.com/process
A Level Switch LFFS-2xx is Ex tD A20 IP67 T100°C, ATEX II 1D approved for application in hasardous areas in accordance with the current EU-directives. The product must be installed in accordance with prevailing guidelines for zone 20 without a barrier.
Ex-dataSupply range 12,5...30 VDC, max 100 mA
Temperature class T100: See table 1
Ex nA II T5, ATEX II 3G - Installation
Level Switch LFFS
12,5..30 VDC
1 2
3
Remote Lamp
A Level Switch LFFS-3xx is Ex nA II T5, ATEX II 3G approved for application in hasardous areas in accordance with the current EU-directives. The product must be installed in accordance with prevailing guidelines for zone 2 without a barrier.
Ex-dataSupply range 12,5...30 VDC, Max. 0.1A
Temperature class T1...T5: See table 1
External lamp Level Switch LFFS
+
-
12,5...30 VDC
Ex tD A20 IP67 T100, ATEX II 1D - Installation
Out
Sortie
Éclairage extérieur
Éclairage à distance
Détecteur de niveau LFFS
Détecteur de niveau LFFS
AUDIN - 8, avenue de la malle - 51370 Saint Brice Courcelles - Tel : 03.26.04.20.21 - Fax : 03.26.04.28.20 - Web : http: www.audin.fr - Email : [email protected]
Page 8 / 8www.baumer.com
FR/1
6101
2
Des
sins
et c
arac
téris
tique
s so
us ré
serv
e de
mod
ifica
tion
sans
pré
avis
Fiche technique LFFS-1
LFFSDétecteur de niveau
Détails de commande
–ModèleDétecteur de niveau LFFS
Sécurité Digit 5'Standard 0Ex ia IIC T5, ATEX II 1G (gaz) * 1Ex tD A20 IP67 T100 °C, ATEX II 1D (poussière) 2Ex nA II T5, ATEX II 3G 3
Raccordements électriques Digit 6'Connecteur M12 en laiton nickelé 1Presseétoupe M16 en laiton 2Presseétoupe M16 en polyamide 3Connecteur M12 en acier inoxydable 4
Connexions de processus Digit 7'G1/2, pointe PEEK (1) 13A/DN38 Raccord hygiénique (1) 2G1/2, pointe PEEK, raccord coulissant, réglable sur 100 mm, avec kit de rondelles 4401 8001 (2) 3G1/2, pointe PEEK, raccord coulissant, réglable sur 250 mm, avec kit de rondelles 4401 8001 (2) 4
Configuration Digit 8'Pas de configuration 0Configuration selon spécifications client C
* Pour une sortie PNP, le modèle de barrière PFOFSI3B25100ALGLS est exigé à des fins de fonctionnement.
Certificat 3A / Certificat EHEDG{1} La marque 3A et le certificat EHEDG sont valables uniquement lorsque le produit est monté dans produit équivalent marqué 3A ou certifié EHEDG et installé conformément au manuel d’installation. Utiliser également un joint torique ou joint d’étanchéité marqué 3A, si approprié. Les produits marqué 3A sont conformes aux critères de la norme sanitaire 3A. Les matériaux et surfaces répondent aux exigences de la FDA et sont certifiés par l’EHEDG. {2} Certifié par l’EHEDG. Répond aux exigences de la FDA.Les joints toriques en EPDM fournis avec les produits marqués 3A sont conformes à la norme sanitaire de classe II (8 % de matière grasse max.) Les joints d’étanchéité en EPDM fournis avec les produits marqués 3A sont conformes à la norme sanitaire de classe I (8 % de matière grasse max.).Se référer aux produits équivalents marqués 3A dans la notice technique « Accessoires universels ».
Exemple de détecteur de niveau LFFS
Page 4 Design and specifications subject to change without notice
Data Sheet LFFS-1www.baumer.com/process
Safety 5´ digitStandard Ex ia IIC T5, ATEX II 1G (Gas) *Ex tD A20 IP67 T100°C, ATEX II 1D (Dust)Ex nA II T5, ATEX II 3G
Electrical Connection 6´ digitPlug, M12Cable gland, M16 brassCable gland, M16 Polyamid
Process Connection 7´ digitG1/2, PEEK tip {1}3A/DN38 Hygienic connection {1}G1/2, PEEK tip, sliding connection, 100 mm adjustable, incl. washer ring kit 4401 8001 {2}G1/2, PEEK tip, sliding connection, 250 mm adjustable, incl. washer ring kit 4401 8001 {2}
Configuration 8´ digitConfiguration according to customer specifications
Ordering Details - Level Switch LFFSLFFS xxx (c)
0 1 2 3
1 2 3
1 2 3 4
c
Note: Ambient temperature range 0...50°C
FlexProgrammer 9701
1
2
Red clip
Black clipThe FlexProgrammer 9701 is a dedicated tool to configure all Baumer configurable Flex-products.
Type No. 9701-0001 comprises: FlexProgrammerCable with 2 aligator clips Cable from FlexProgrammer to M12 plug for TE2 Cable from FlexProgrammer to M12 Plug for LFFS, LBFS, CPXUSB cableCD with the FlexProgram software
Disconnect the power supply before connecting the FlexProgrammer 9701 to the Level Switch LFFS
PEEK naturaAngle > 135 deg.
EPDM O-rings supplied with 3-A marked products are conform to Sanitary Standard Class II (8% milk fat max.)
EPDM gaskets supplied with 3-A marked products are conform to Sanitary Standard Class I (8% milk fat max.)
Refer to the 3-A marked counter parts in the data sheet “Accessories Universal”.
Level Switch LFFS, example
1
2
1
2
The washer ring kit for sliding connection, type no. 4401 8001 Can be ordered separately. Baumer recommended to replace this kit if deformed.
* Recommended isolating module: PROFSI3-B25100-ALG-LS
{1} The 3-A mark and the EHEDG certifcate is valid only when the product is mounted in a 3-A marked or EHEDG certified counter part and installed according to the installation manual. Use also a 3-A marked O-ring or gasket if relevant. The 3-A marked products conforms to the 3-A Sanitary Standard criteria. Materials and surfaces fulfill the FDA demands and are certified by EHEDG.
{2} Certified by EHEDG. Fulfills the FDA demand.
3A certificate / EHEDG certificate
Configuration Accessories
(1) La marque 3A et le certificat EHEDG sont valables uniquement lorsque le produit est monté dans produit équivalent marqué 3A ou certifié EHEDG et installé conformément au manuel d’installation. Utiliser également un joint torique ou joint d’étanchéité marqué 3A, si approprié. Les produits marqué 3A sont conformes aux critères de la norme sanitaire 3A. Les matériaux et surfaces répondent aux exigences de la FDA et sont certifiés par l’EHEDG. (2) Certifié par l’EHEDG. Répond aux exigences de la FDA. Les joints toriques en EPDM fournis avec les produits marqués 3A sont conformes à la norme sanitaire de classe II (8 % de matière grasse max.) Les joints d’étanchéité en EPDM fournis avec les pro-duits marqués 3A sont conformes à la norme sanitaire de classe I (8 % de matière grasse max.) Se référer aux produits équivalents marqués 3A dans la notice technique « Accessoires universels ».
Le kit de rondelles pour raccord coulissant, type n° 4401 8001, peut être commandé séparément. Baumer recommande de remplacer ce kit en cas de déformation.
PEEK NaturaAngle > 135 deg.
AUDIN - 8, avenue de la malle - 51370 Saint Brice Courcelles - Tel : 03.26.04.20.21 - Fax : 03.26.04.28.20 - Web : http: www.audin.fr - Email : [email protected]