Upload
vankhuong
View
230
Download
2
Embed Size (px)
Citation preview
Schüco Fassade USC 65 Schüco Façade USC 65
30 | Schüco
Schüco Fassade USC 65 Schüco Façade USC 65
Schüco | 31
Schü
co U
SC 6
5
Schüco Fassade USC 65 Schüco Façade USC 65
Schüco USC 65 (Unitized System Construction) ist eine vielseitige Systemlösung, die durch seine architektonisch, anspruchvollen Designvarianten Gestaltungs-freiheit bietet: Schüco USC 65 F, eine Elementfassade mit Rahme-noptik überzeugt genauso durch seine ästhetischen Ansprüche wie Schüco USC 65 FSG, eine Semi-Structural Glazing-Element-fassade.
Schüco USC 65 (Unitised System Construction) is a versatile system solution which offers design freedom due to its architecturally sophisticated design options. Schüco USC 65 F, a unitised façade with a framed look, has impressive aesthetic standards, as does Schüco USC 65 FSG, a semi-structural glazing unitised façade.
32 Systemeigenschaften System properties
36 Prüfzeugnisse Test certificates
40 Konstruktionsprinzipien Construction principles
45 Anwendungsbeispiele Examples
74 Profilübersicht Overview of profiles
Systemeigenschaften System properties
32 | Schüco
10
65 Eigenschaften und Vorteile Umlaufend schmale Ansichtsbreite bis zu 65 mm Gestaltungsvarianten:
RahmenoptikSemi-Structural Glazing
Variable Elementgliederung durch Sprossen Senkrechte Sprossen Waagerechte Sprossen Gekreuzte Sprossen
Große Elementabmessungen und Elementgewichte möglich:
Bautiefen 125 und 150 mm Statisch optimierte Profilgeometrien Asymmetrische Eckverbinder für große Glaslasten
Fassadenbefestigung für Einfeld- und Durchlauf-träger Variable Anpassung an unterschiedliche Anforderungen an die Wärmedämmung durch 3 unterschiedliche Isoliersteglängen Glasdicken:
Einfachglas von 4 - 16 mm Isolierglas von 16 - 56 mm
Variables Dichtungsprogramm für: 10 mm horizontale Stoßfuge, Aufnahme von +/- 5 mm Dehnung 20 mm horizontale Stoßfuge, Aufnahme von +/- 10 mm Dehnung
Hohe Dichtigkeit durch: Überlappendes Dichtungsprinzip bei Kopplungs- und Satteldichtung 3-Kammer-Prinzip
System Schüco e-connect: Keine Undichtigkeiten bei der Leitungsführung von innen nach außen Keine Beschädigung der Leitung beim Leitungsübergang Reduzierte Gefahr fehlerhafter elektrischer Anschlüsse durch eindeutige Gewerkeschnitt-stelle
Einsatzelemente: Schüco AWS 102Schüco AWS 70 BS.HISchüco AWS 75 BS.HI
Umfangreiche Systemprüfungen nach europäischen und amerikanischen Normen
••
••
••••
•
•••
•
•
•••
••
•
••
••
•
•
•
••••
•
Schüco Fassade USC 65 F Schüco Façade USC 65 F
Maßstab 1:1 Scale 1:1
Systemeigenschaften Schüco Fassade USC 65 System properties for Schüco Façade USC 65
Systemeigenschaften System properties
Schüco | 33
10
65
Schü
co U
SC 6
5
Schüco Fassade USC 65 FSG Schüco Façade USC 65 FSG
Maßstab 1:1 Scale 1:1
Features and benefits All-round narrow face widths (up to 65 mm) Design types:
Framed lookSemi-structural glazing
Different unit divisions created by glazing bars Vertical glazing bars Horizontal glazing bars Crossed glazing bars
Large unit dimensions and heavy unit weights possible:
125 mm and 150 mm basic depths Structurally optimised profile geometries Asymmetric corner cleats for large glass loads
Façade fixing brackets for single-field and continuous beams Can be adjusted to meet different thermal insulation requirements thanks to 3 different insulating bar lengths Glass thicknesses:
Single glazing from 4 - 16 mm Insulating glass from 16 - 56 mm
Different gaskets for: 10 mm horizontal butt joint, to take up an expansion of +/- 5 mm 20 mm horizontal butt joint, to take up an expansion of +/- 5 mm
Excellent weathertightness due to: Overlapping gasket design for coupling gasket and saddle gasket 3-chamber principle
Schüco e-connect system: Sealed wiring from inside to outside No damage to the wiring where cable is connectedSingle connection interface reduces danger of defective electrical connections
Insert units: Schüco AWS 102Schüco AWS 70 BS.HISchüco AWS 75 BS.HI
Extensive system tests in accordance with European and American standards
••
••
••••
•
•••
•
•
•••
••
•
••
••
••
•
••••
•
Systemeigenschaften System properties
34 | Schüco
Übersicht der Gestaltungsvarianten Overview of design options
Schüco USC 65 F Elementfassade mit Rahmenoptik Schüco USC 65 F unitised façade with framed look
Maßstab 1:4 Scale 1:4
Zur Realisierung unterschied-licher architektonischer Entwürfe bietet das System Schüco USC 65 interessante Gestaltungsvarianten: Schüco USC 65 F als Elementfassade mit Rahmenoptik sowie Schüco USC 65 FSG in Ganzglas-Optik mit horizontal oder vertikal angeordneten Glasleisten.
Different architectural designs to be created can be created using the interesting design options of the Schüco USC 65 system: Schüco USC 65 F as a unitised façade with framed look and Schüco USC 65 FSG in an all-glass look with horizontally or vertically arranged glazing beads.
Systemeigenschaften System properties
Schüco | 35
Schü
co U
SC 6
5
Schüco USC 65 FSG Elementfassade mit Semi-Structural Glazing-Optik und horizontaler Betonung Schüco USC 65 FSG unitised façade with semi-structural glazing look and horizontal emphasis
Schüco USC 65 FSG Elementfassade mit Semi-Structural Glazing-Optik und vertikaler Betonung Schüco USC 65 FSG unitised façade with semi-structural glazing look and vertical emphasis
Maßstab 1:4 Scale 1:4
Prüfzeugnisse Test certificates
36 | Schüco
Art der Prüfung Type of test
Norm Standard
Prüfinstitut Test institute
Prüfzeugnis Test certificate
Prüfergebnis Test result
Luftdurchlässigkeit Air permeability
EN 12153 ift-Rosenheim 10835288 AE
Schlagregendichtigkeit Watertightness
EN 12155 ift-Rosenheim 10835288 RE 1200
Windlast Wind load
EN 12179 ift-Rosenheim 108352881,5 KN/m2
2,25 KN/m2
Stoßfestigkeit Impact resistance
EN 13049 ift-Rosenheim 10835288 I5 / E5
Luftschalldämmung Airborne sound reduction
EN ISO 717-1 ift-Rosenheim 16928386/3siehe nachfolgende Seite See following page
Wärmedämmung Thermal insulation
DIN EN ISO 10077,T2eigene Berechnung Own calculation
siehe nachfolgende Seite See following page
Absturzsicherheit (Pendelschlagversuch) Protection against glass falling out (Pendulum impact test)
E-TRAVDIN EN 12600
PSP RWTH Aachen
auf Anfrage On request
voll absturzsichernd Full safety barrier
Allgemeine bauaufsichtliche Zulassung General building approval
DIBtauf Anfrage On request
siehe Bericht See report
Brandschutz / KaltbrüstungFire protection / ventilated spandrel
DIN 4102-3MPA Braunschweig
beantragt Pending
W90
Air, Water, Structural, Interstory Movement, Seismic
ASTM E 283-04ASTM E 331-00ASTM E 330-02AAMA 501.4
ATI 81184.02-120-47siehe Bericht See report
Prüfzeugnisse Test certificates
Prüfzeugnisse Test certificates
Schüco | 37
Schü
co U
SC 6
5
Bewertetes Schalldämm-Maß Airborne sound reduction index
Schüco-System Schüco system
Prüfzeugnis Test certificate
Empfohlene Verglasung Recommended glazing
R‘45°, w = 36 dB 16434412/R1
[6-(16)-6]andere Glasaufbauten auf
Anfrage Other glazing configurations
on request
R‘45°, w = 40 dB 16434412/R1
[6-(12)-9 VSG SF]andere Glasaufbauten auf
Anfrage Other glazing configurations
on request
Schallschutz Sound reduction
Hinweis: Bei Verwendung von Schallschutzgläsern ist darauf zu achten, daß die vom Lieferanten für das Glas angegebenen Schalldämmwerte nach der neuesten Prüfnorm ermittelt wurden.
Note: When using sound reduction glazing, it is important to ensure that the sound reduction values given by the supplier have been calculated in accordance with the most recent test norms.
Prüfzeugnisse Test certificates
38 | Schüco
Wärmedämmung Thermal insulation
Schüco Fassade USC 65 F Schüco Façade USC 65 F
Uf-Wert in W/m2K nach DIN EN ISO 10077, T2 Uf value in W/m2K in accordance with DIN EN ISO 10077, part 2
mm
x
mm 125 mm 150 mm
25
22 3,23 3,27
23 - 30 3,00 3,03
31 - 38 2,91 2,94
32,5
30 2,43 2,45
31 - 38 2,27 2,29
39 - 46 2,20 2,23
42,5
40 1,91 1,93
41 - 48 1,83 1,84
49 - 56 1,78 1,79
mm
x
mm 44 mm 124 mm 149 mm
25
22 2,71 2,86 2,88
23 - 30 2,64 2,80 2,83
31 - 38 2,63 2,82 2,86
32,5
30 2,30 2,42 2,43
31 - 38 2,21 2,33 2,35
39 - 46 2,23 2,37 2,39
42,5
40 2,01 2,08 2,09
41 - 48 1,96 2,04 2,06
49 - 56 1,98 2,08 2,10
Maßstab 1:2 Scale 1:2
Maßstab 1:2 Scale 1:2
Uf-Wert in W/m2K nach DIN EN ISO 10077, T2 Uf value in W/m2K in accordance with DIN EN ISO 10077, part 2
Prüfzeugnisse Test certificates
Schüco | 39
Schü
co U
SC 6
5
Schüco Fassade USC 65 FSG Schüco Façade USC 65 FSG
Maßstab 1:2 Scale 1:2
Maßstab 1:2 Scale 1:2
Uf-Wert in W/m2K nach DIN EN ISO 10077, T2 Uf value in W/m2K in accordance with DIN EN ISO 10077, part 2
mm
x
mm 125 mm 150 mm
25
32 2,67 2,69
33 - 40 2,52 2,54
41 - 48 2,44 2,46
32,5
42 2,07 2,08
43 - 50 1,97 1,98
51 - 58 1,95 1,96
mm
x
mm 44 mm 124 mm 149 mm
25
32 2,29 2,39 2,41
33 - 40 2,17 2,28 2,30
41 - 48 2,18 2,28 2,29
32,5
42 1,99 2,06 2,08
43 - 50 1,91 1,98 2,00
51 - 58 1,90 1,99 2,00
Uf-Wert in W/m2K nach DIN EN ISO 10077, T2 Uf value in W/m2K in accordance with DIN EN ISO 10077, part 2
Konstruktionsprinzipien Construction principles
40 | Schüco
Überlappendes Dichtungsprinzip Overlapping gasket design
Konstruktionsprinzipien Construction principles
Konstruktionsprinzipien Construction principles
Schüco | 41
Schü
co U
SC 6
5
Die vertikalen Kopplungsdich-tungen werden überlappend montiert. Die Überlappung erfolgt über die Satteldichtung (Elementaußenseite) bzw. über die horizontale Kopplungsdichtung (Elementinnenseite)
Die horizontalen Kopplungs- und Satteldichtungen werden auf der Baustelle über mehrere Elemente durchlau-fend montiert. Ein eventueller Satteldichtungsstoß hat in Feldmitte zu erfolgen
Die Montage der vertikalen Kopplungsdichtung erfolgt bereits einseitig in der Werkstatt
Zur Ableitung von eventuell anfallendem Kondensat aus dem System, wird die Sattel-dichtung versetzt, auf einer Breite von 10 mm eingeschnitten
The vertical coupling gaskets are mounted so that they overlap. They overlap with the saddle gasket (external side of unit) or with the horizontal coupling gasket (internal side of unit)
The horizontal coupling gaskets and the saddle gaskets are mounted continuously across several units on the construction site. Any saddle gasket butt joint must be positioned in the centre of the field
The vertical coupling gasket is already mounted on one side in the workshop
The saddle gasket is offset and notched to a width of 10 mm to drain any condensation from the system
Konstruktionsprinzipien Construction principles
42 | Schüco
Maßstab 1:2 Scale 1:2
Verarbeitung und Verglasung Schüco USC 65 FSG Fabrication and glazing for Schüco USC 65 FSG
Konstruktionsprinzipien Construction principles
Schüco | 43
Schü
co U
SC 6
5
Grundsätzlich sind bei der Versiegelung und bei der Structural Glazing-Verklebung bezüglich der Haftung und Verträglichkeit mit dem Randverbund die Verarbeitungsrichtlinien der Dichtstofflieferanten wie Dow Corning oder Sika zu beachten. Ebenso muss die Verträglichkeit mit Silikon- und EPDM-Profilen sowie Butylbändern gesichert sein.
Versiegelung (aussteifend) Die Versiegelung der Glasfugen muss mit UV-beständigem Silikon Klebstoff z. B. Dow Corning® 993, Dow Corning® 895, Sikasil® SG-500 oder Sikasil® SG-20 erfolgen.
Structural Glazing-Verklebung Die Structural Glazing-Verklebung muss mit UV-beständigem Silikon Klebstoff z. B. Dow Corning® 993, Dow Corning® 895, Sikasil® SG-500 oder Sikasil® SG-20 erfolgen.
Aluminiumoberfläche Die äußere Aluminium-Schale des Rahmens bzw. der Sprosse ist in Eloxaltönen C0 bis C35 ausführbar.
Eckausbildung Im Bereich der Eckausbildung empfiehlt die Glasindustrie einen dichtstofffreien Falz, um Kondensat abzuleiten und einen Dampfdruck-ausgleich nach außen (z. B. über die Riegel) zu gewährleisten. Öffnungen in den einzusetzenden Silikon-Hohlprofilen dürfen oben wie unten nicht verschlossen werden. Die zu verwendende Glasart ist nach den jeweils gültigen baurechtlichen Vorschriften auszuwählen (ESG, TVG, VSG). Es sind die technischen Richtlinien für linien-förmig gelagerte Verglasungen zu beachten. Die Glaskantenbearbeitung ist mit dem Glas-lieferanten abzustimmen. Ein statischer Nachweis für die Ganzglasecke muss erfolgen.
Isolierglas Es dürfen nur Isoliergläser mit UV-beständigen Randverbund verwendet werden. Alle Kombi-nationen von Glas, Klebstoff und Vorfüller sind mit den Glas-Klebstoff- und Dichtstofflieferanten abzustimmen (Gewährleistung).
Scheibenüberstand Scheibenüberstand aus optischen Gründen abspachteln, bedrucken, etc.
When sealing and bonding the structural glazing, observe the guidelines provided by the sealant supplier, such as Dow Corning or Sika, relating to adhesion and compatibility with the edge bonding of the glazing units. It is also important to ensure compatibility with silicone and EPDM profiles and butyl tape.
Sealing (reinforcing) Use a UV-resistant silicone sealing compound, e.g. Dow Corning® 993, Dow Corning® 895, Sikasil® SG-500 or Sikasil® SG-20, to seal the glass joints.
Structural glazing bonding Use a UV-resistant silicone sealing compound, such as Dow Corning® 993, Dow Corning® 895, Sikasil® SG-500 or Sikasil® SG-20, to bond the structural glazing.
Aluminium surface The outer aluminium skin of the frame and the glazing bar are available in anodised colours C0 to C35.
Corner construction The glass industry recommends the use of a sealant-free rebate for corner constructions in order to channel condensation and to ensure pressure equalisation with the outside (e.g. via the transoms). Openings in the silicone hollow profiles to be inserted must not be closed at the top or the bottom. The type of glazing to be used must be selected in accordance with the relevant construction regulations (toughened safety glass, partially toughened safety glass, laminated safey glass). The technical regulations for overhead glazing must be observed. The preparation of the glass edge must be agreed with the glass supplier. Structural calculations must be supplied for all-glass corners.
Insulating glass Only use insulating glass with UV-resistant edge seals. All combinations of glass, silicone adhesive and pre-filler should be agreed with the glass adhesive and sealant suppliers (warranty).
Glass overlap The stepped edge unit can either be coated or ceramic fritted to give a uniform appearance.
Konstruktionsprinzipien Construction principles
44 | Schüco
Maximale Glaslasten und Elementgrößen Maximum glass loads and unit sizes
Einfeldraster Single module
Doppelraster Double module
Lastabtragung auch über Sprosse Load is also transferred to the glazing bar
max. Elementbreite Max. unit width
Profilauswahl Profile selection
2700 mm 2700 mm
max. Elementhöhe Max. unit height 3600 mm 3600 mm
max. Scheibengewicht Max. pane weight
125
125 mm
150
150 mm
125 kg 125 kg
125 kg 125 kg
250 kg 250 kg
max. Elementbreite Max. unit width
Profilauswahl Profile selection
1350 mm 1350 mm
max. Elementhöhe Max. unit height 3600 mm 3600 mm
max. Scheibengewicht Max. pane weight
125
125 mm
150
150 mm
500 kg
350 kg
150 kg
Anwendungsbeispiele Examples
Schüco | 45
Schü
co U
SC 6
5
Übersicht der Anwendungsbeispiele Overview of examples
Anwendungsbeispiele Schüco Fassade USC 65 FSG Examples Schüco Façade USC 65 FSG
Die hier gezeigten Element-symbole geben eine Übersicht der möglichen Bauformen. Alle auf dieser Seite angegebenen Zahlen sind Seitenzahlen zu den im Folgenden gezeigten Anwendungsbeispielen.
The diagrams shown here provide an overview of the different shapes that are possible. The numbers below are the page numbers for the relevant examples.
Anwendungsbeispiele Schüco Fassade USC 65 F Examples Schüco Façade USC 65 F
51464849505253
4748495054
525556586263
56575960
61
6466676869707473
65666768707172
73
Anwendungsbeispiele Examples
46 | Schüco
2432
1512
5
10
65
Anwendungsbeispiele Schüco Fassade USC 65 F Examples for Schüco Façade USC 65 F
Rahmen mit horizontaler Dehnfuge 10 mm Frame with 10 mm horizontal expansion gap
Maßstab 1:1 Scale 1:1
Anwendungsbeispiele Examples
Schüco | 47
12524 32 15
10 65
Schü
co U
SC 6
5
Anwendungsbeispiele Examples
48 | Schüco
65
2432
1512
5
10
75
24 32 15 125
20
Maßstab 1:2 Scale 1:2
Rahmen mit horizontaler Dehnfuge 20 mm Frame with 20 mm horizontal expansion gap
Anwendungsbeispiele Examples
Schüco | 49
65
2432
1512
5
10
65
24 32 15 125
10
Schü
co U
SC 6
5
Rahmen für große Elementgewichte mit horizontaler Dehnfuge 10 mm Frame for large unit weights with 10 mm horizontal expansion gap
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
50 | Schüco
65
2432
1512
5
10
24 32 15 125
7520
Rahmen für große Elementgewichte mit horizontaler Dehnfuge 20 mm Frame for large unit weights with 20 mm horizontal expansion gap
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
Schüco | 51
2432
1512
51.5°1.
5°
65
24 32 15 125
10
Schü
co U
SC 6
5
Außensegmentierung External faceting
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
52 | Schüco
27.5
1027
.565
10
65
1091
90° Außenecke 90° outer corner
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
Schüco | 53
27.5
10
2432
1512
5
10
65
2132
1512
4
27.5
Schü
co U
SC 6
5
Rahmen mit vertikaler Sprosse Frame with vertical glazing bar
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
54 | Schüco
21 32 15 124
6510
27.5
24 32 15 125
10
27.5
Rahmen mit horizontaler E-Sprosse Frame with horizontal e-glazing bar
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
Schüco | 55
Schü
co U
SC 6
5
Sonnenschutz Solar shading
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
56 | Schüco
3212
5
10
65
15
32 1515 125
6510
Kaltbrüstung mit Einfachglas Ventilated spandrel with single glazing
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
Schüco | 57
Schü
co U
SC 6
5
Kaltbrüstung der Feuerwiderstandsklasse W90 Ventilated spandrel in fire-resistance class W90
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
58 | Schüco
70A4 70A4
70A4 70A4
Fassadenbefestigung und Kaltbrüstung der Feuerwiderstandsklasse W90 Façade fixing bracket and ventilated spandrel in fire-resistance class W90
Maßstab 1:4 Scale 1:4
Anwendungsbeispiele Examples
Schüco | 59
Schü
co U
SC 6
5
Seitlicher Baukörperanschluss mit Kaltbrüstung der Feuerwiderstandsklasse W90 Side attachment to building structure with ventilated spandrel in fire-resistance class W90
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
60 | Schüco
Seitlicher Baukörperanschluss Side attachment to building structure
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
Schüco | 61
Schü
co U
SC 6
5
Unterer Baukörperanschluss Bottom attachment to building structure
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
62 | Schüco
10
Fassadenbefestigung und Kaltbrüstung mit Einfachglas Façade fixing bracket and ventilated spandrel with single glazing
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
Schüco | 63
70A470A4
70A470A4
Schü
co U
SC 6
5
Oberer Baukörperabschluss Top attachment to building structure
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
64 | Schüco
3615
125
10
65
Rahmen mit horizontaler Dehnfuge 10 mm Frame with 10 mm horizontal expansion gap
Maßstab 1:1 Scale 1:1
Anwendungsbeispiele Schüco Fassade USC 65 FSG Examples for Schüco Façade USC 65 FSG
Anwendungsbeispiele Examples
Schüco | 65
12536 15
10 65
Schü
co U
SC 6
5
Anwendungsbeispiele Examples
66 | Schüco
3615
125
10
65
75
36 15 125
20
Rahmen mit horizontaler Dehnfuge 20 mm Frame with 20 mm horizontal expansion gap
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
Schüco | 67
3615
125
10
65
65
36 15 125
10
Schü
co U
SC 6
5
Rahmen für große Elementgewichte mit horizontaler Dehnfuge 10 mm Frame for large unit weights with 10 mm horizontal expansion gap
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
68 | Schüco
3615
125
10
65
36 15 125
7520
Maßstab 1:2 Scale 1:2
Rahmen für große Elementgewichte mit horizontaler Dehnfuge 20 mm Frame for large unit weights with 20 mm horizontal expansion gap
Anwendungsbeispiele Examples
Schüco | 69
3615
125
27.5 65
3615
124
1010
27.5
Schü
co U
SC 6
5
Rahmen mit vertikaler Sprosse Frame with vertical glazing bar
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
70 | Schüco
65
3615
125
10
65
20 36 15 125
10
Vertikale Betonung, Dehnfuge 10 mm Vertical emphasis, 10 mm expansion gap
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
Schüco | 71
27.5
20 36 15 12565
20 36 15 124
27.5
101010
Schü
co U
SC 6
5
Maßstab 1:2 Scale 1:2
Vertikale Betonung, Dehnfuge 10 mm Vertical emphasis, 10 mm expansion gap
Anwendungsbeispiele Examples
72 | Schüco
65
3615
125
10
20 36 15 125
27.5
20
Vertikale Betonung, Dehnfuge 20 mm Vertical emphasis, 20 mm expansion gap
Maßstab 1:2 Scale 1:2
Anwendungsbeispiele Examples
Schüco | 73
65
27.5
27.5
Schü
co U
SC 6
5
90° Structural Glazing-Außenecke 90° structural glazing outer corner
Maßstab 1:2 Scale 1:2
Profilübersicht Overview of profiles
74 | Schüco
Profilübersicht Schüco Fassade USC 65 Overview of profiles for Schüco façade USC 65
Rahmenprofile Schüco USC 65 F Schüco USC 65 F frame profile
125
181.
3
65
10
150
206.
3
65
10
125
188.
8
65
10
150
213.
8
65
10
125
198.
8
65
10
150
223.
8
65
10
331 990
331 980
331 970
331 960
331 950
331 940
85
9.5
125
110
9.5
150
338 160 351 650
Einschiebprofile Insert profiles
Ix
Iy
cm4 cm4
338 160 38,63 0,23
351 650 74,29 0,23
Ix
Iyx
cm4 cm4 mm
331 940 177,09 6,85 25
331 950 259,99 7,53 25
331 960 189,4 6,85 32.5
331 970 274,01 7,53 32.5
331 980 207,24 6,85 42.5
331 990 294,16 7,53 42.5
Profilübersicht Overview of profiles
Schüco | 75
125
181.3
6510
125
188.8
6510
125
198.8
6510
150
206.3
6510
150
213.8
6510
150
223.8
6510
Schü
co U
SC 6
5
Verstärkte Rahmenprofile Schüco USC 65 F Schüco USC 65 F reinforced frame profiles
325 410
325 420
325 430
325 810
325 820
325 830 Maßstab 1:4 Scale 1:4
Ix
Iyx
cm4 cm4 mm
325 410 183,51 17,96 25.0
325 420 195,98 17,96 32.5
325 430 214,04 17,96 42.5
325 810 273,42 20,03 25.0
325 820 287,84 20,03 32.5
325 830 308,54 20,03 42.5
Profilübersicht Overview of profiles
76 | Schüco
Rahmenprofile Schüco USC 65 FSG Schüco USC 65 FSG frame profiles
125
162
65
10
125
169.
5
65
10
150
194.
5
65
10
325 350
325 340
150
187
65
10
325 330
325 320
85
9.5
125
110
9.5
150
338 160 351 650
Einschiebprofile Insert profiles
Ix
Iy
cm4 cm4
338 160 38,63 0,23
351 650 74,29 0,23
Ix
Iyx
cm4 cm4 mm
325 320 140,2 6,2 25
325 330 213,49 6,84 25
325 340 147,28 6,2 32.5
325 350 221,56 6,84 32.5
Profilübersicht Overview of profiles
Schüco | 77
125
162
6510
125
169.5
6510
150
187
6510
150
194.5
6510
Schü
co U
SC 6
5
Verstärkte Rahmenprofile Schüco USC 65 FSG Schüco USC 65 FSG reinforced frame profiles
325 980
325 990
353 800
353 850
Maßstab 1:4 Scale 1:4
Ix
Iyx
cm4 cm4 mm
325 980 145,9 17,79 25.0
325 990 153,05 17,79 32.5
353 800 224,64 19,83 25.0
353 850 232,92 19,83 32.5
Profilübersicht Overview of profiles
78 | Schüco
124
180.
3
65
149
205.
5
65
Sprossenprofile Schüco USC 65 F Schüco USC 65 F glazing bar profiles
100.
3
44
65
331 720
331 730
44
117.
8
65
331 780
107.
85
44
65
331 750
124
187.
8
65
331 760
124
197.
865
331 790
331 740
149
222.
8
65
331 800
149
212.
8
65
331 770
Ix
Iy
cm4 cm4
331 720 59,96 36,46
331 730 308,64 72,48
331 740 441,2 82,06
331 750 72,63 36,46
331 760 331,5 72,48
331 770 467,27 82,06
331 780 91,83 36,46
331 790 364,77 72,48
331 800 504,96 82,06
Profilübersicht Overview of profiles
Schüco | 79
124
168.
55
64.7
125
59
149
Schü
co U
SC 6
5
Ix
Iy
cm4 cm4
331 830 39,45 35,23
331 840 258,01 71,24
331 850 378,02 80,82
331 860 47,99 35,23
331 870 273,97 71,24
331 880 396,49 80,82
Sprossenprofile Schüco USC 65 FSG Schüco USC 65 FSG glazing bar profiles
44
81.0
5
65
331 830 12
4
161
65
331 840
44
88.5
5
65
331 860
331 870
149
186
65
331 850
149
193.
5
65
331 880
Sprossen Einschiebprofil Glazing bar insert profile
351 620
Ix
Iy
cm4 cm4
351 620 240,93 39,57
Maßstab 1:4 Scale 1:4
Profilübersicht Overview of profiles
80 | Schüco
E-Sprossenprofile Schüco USC 65 F Schüco USC 65 F e-glazing bar profiles
E-Sprossenprofile Schüco USC 65 FSG Schüco USC 65 FSG e-glazing bar profiles
122.
35
178.
7
64.9
331 890
122.
4
186.
2
65
331 900
122.
4
196.
2
65
331 910
122.
4
159.
4
64.9
331 920
122.
4
166.
9
65
331 930
Ix
Iy
cm4 cm4
331 890 284,3 74,96
331 900 307,06 74,96
331 910 340,23 74,96
Ix
Iy
cm4 cm4
331 920 234,19 73,73
331 930 250,09 73,73
65
203 022
336 950
Deckschale für E-Sprossenprofil Cover cap for e-glazing bar profile
Profilübersicht Overview of profiles
Schüco | 81
Schü
co U
SC 6
5
Ix
Iy
cm4 cm4
324 330 236,91 21,37
338 060 1146,74 116,46
Eckpfosten Corner mullions
Glasleisten für 90° Außenecke Glazing beads for 90° outer corner
Glasleisten Glazing beads
Abdeckprofile für horizontale Betonung Cover profiles for horizontal emphasis
80
33
102
65
225.
5
324 330 338 060
91
15
53.5
46
325 680 325 690
27.5
1512
27.5
27.5
1512
27.5
325 280 307 070* 325 360 307 060 *
70
19
19
80
336 450 336 490 Maßstab 1:4 Scale 1:4
* Nur für Eloxal geeignet Only suitable for anodising