7
7/26/2019 Sds - Anco Micro Blend http://slidepdf.com/reader/full/sds-anco-micro-blend 1/7 Safety Data Sheet Prepared for:  Anchor Drilling Fluids USA, Inc. 2431 East 61 st  Street, Suite 710, Tulsa, Oklahoma 74136 918.583.7701 October 7, 2013 Section 1: Identification Identification of the chemical as well as the recommended uses and the essential contact information of the supplier. Product Identifier:  ANCO Micro Blend Common Name(s): N/A Chemical Family: N/A Synonyms: Ground plant fibers and minerals Manufacturer, Importer, and/or Responsible Party Information Name:  Anchor Drilling Fluids USA, Inc. Address: 2431 East 61 st  Street, Suite 710, Tulsa, Oklahoma 74136 Phone Number: 918.583.7701 Emergency Phone Number: CHEMTREC 800.424.9300 Recommended Use of Chemical Chemical Services: Drilling Operations Use Restrictions: None Section 2: Hazard(s) Identification Identification of the hazards of the chemical presented and the appropriate warning information associated with those hazards. Hazard Classification: C.4.1, C.4.2 & C.4.3 Acute Toxicity - Oral, Dermal & Inhalation: Hazard Category 3 Signal Word: Danger Hazard Statement(s): Harmful if swallowed, harmful in contact with skin, harmful if inhaled, can cause skin irritation, may cause allergy or asthma symptoms or breathing difficulties or respiratory irritation if inhaled, Pictogram(s): Precautionary Statement(s): Wash thoroughly after handling, do not eat, drink or smoke when using this product, wear protective gloves/protective clothing, avoid breathing dust/fumes/gas/mist/vapors/spray, use only outdoors or in a well-ventilated area, if proper ventilation is not possible wear proper respiratory protection Description of any hazards not otherwise classified: N/A Mixture Identification (if toxicity is unknown) Percentage of the mixture consisting of ingredient(s) with unknown toxicity: NDA Note: this is a total percentage of the mixture and not tied to the individual ingredient(s).

Sds - Anco Micro Blend

Embed Size (px)

Citation preview

Page 1: Sds - Anco Micro Blend

7/26/2019 Sds - Anco Micro Blend

http://slidepdf.com/reader/full/sds-anco-micro-blend 1/7

Safety Data SheetPrepared for:

 Anchor Drilling Fluids USA, Inc.2431 East 61st Street, Suite 710,

Tulsa, Oklahoma 74136918.583.7701

October 7, 2013

Section 1: Identification

Identification of the chemical as well as the recommended uses and the essential contactinformation of the supplier.

Product Identifier:  ANCO Micro BlendCommon Name(s): N/A

Chemical Family: N/A

Synonyms: Ground plant fibers and mineralsManufacturer, Importer, and/or Responsible Party Information

Name:  Anchor Drilling Fluids USA, Inc.Address: 2431 East 61st Street, Suite 710, Tulsa, Oklahoma 74136Phone Number: 918.583.7701Emergency Phone Number: CHEMTREC 800.424.9300

Recommended Use of ChemicalChemical Services: Drilling OperationsUse Restrictions: None

Section 2: Hazard(s) Identification

Identification of the hazards of the chemical presented and the appropriate warning informationassociated with those hazards.

Hazard Classification:C.4.1, C.4.2 & C.4.3 Acute Toxicity - Oral, Dermal & Inhalation:Hazard Category 3

Signal Word: Danger

Hazard Statement(s):Harmful if swallowed, harmful in contact with skin, harmful if inhaled,can cause skin irritation, may cause allergy or asthma symptoms orbreathing difficulties or respiratory irritation if inhaled,

Pictogram(s):

PrecautionaryStatement(s):

Wash thoroughly after handling, do not eat, drink or smoke when using this

product, wear protective gloves/protective clothing, avoid breathingdust/fumes/gas/mist/vapors/spray, use only outdoors or in a well-ventilatedarea, if proper ventilation is not possible wear proper respiratory protection

Description of any hazards not otherwise classified: N/A

Mixture Identification (if toxicity is unknown)

Percentage of the mixture consistingof ingredient(s) with unknown toxicity:

NDA

Note: this is a total percentage of the mixture and not tied to the individual ingredient(s).

Page 2: Sds - Anco Micro Blend

7/26/2019 Sds - Anco Micro Blend

http://slidepdf.com/reader/full/sds-anco-micro-blend 2/7

Section 3: Composition/Information on Ingredients

Identification of the ingredient(s) contained in the product, including impurities and stabilizingadditives. This section includes information on substances, mixtures and all chemicals where a

trade secret is claimed.

Substances

Product is a mixtureMixtures

Chemical Namesand Concentrations:

Plant fibers and minerals

Common Name: NoneSynonym(s): NoneChemical Abstract Service (CAS) Number: None

Any other unique identifiers: NoneImpurities and stabilizing additives (which arethemselves classified and which contribute tothe classification of the chemical):

None

Recommended Use of ChemicalChemical Services: Drilling operationsUse Restrictions: N/A

Trade Secret

Is the specific chemical identity and/or exactconcentration of composition withheld as a trade secret?

No

Section 4: First-Aid Measures

Description of the initial care that should be given by untrained responders to an individual whohas been exposed to the chemical.

Necessary first-aid instructions

Inhalation: Remove person to fresh air. Call a physician if irritation developsAcute Symptomsof Inhalation:

Irritation

Delayed Symptoms of Inhalation: None known

Skin Contact:Wash with large amounts of soap and water and call a physician if irritationdevelops

Acute Symptomsof Skin Contact:

Possible irritation

Delayed Symptoms of Skin Contact: None known

Eye Contact:Wash thoroughly with water for a minimum of 15 minutes. If irritation developscall a physician.

Acute Symptoms

of Eye Contact:

Possible irritation

Delayed Symptoms of Eye Contact: None known

Ingestion: If large amounts of this product are ingested, give water and call a physicianAcute Symptomsof Ingestion:

Possible irritation

Delayed Symptoms of Ingestion: None knownImmediate Medical Care / Special Treatment

Is immediate medical care or special treatment required? NoIf so, what is needed: N/A

Page 3: Sds - Anco Micro Blend

7/26/2019 Sds - Anco Micro Blend

http://slidepdf.com/reader/full/sds-anco-micro-blend 3/7

Section 5: Fire-Fighting Measures

Recommendations for fighting a fire caused by or including the chemical.Suitable Extinguishing Equipment: Water, Foam, CO2 and FogExtinguishing equipment not appropriate: N/A

Specific hazards created

from chemical burning:

Dust may be explosive in the finely divided and suspended state

and exposed to ignition sourceSpecial protectiveequipment needed:

Wear NIOSH approved self-contained breathing apparatus and fullprotective gear

Section 6: Accidental Release Measures

Recommendations on the appropriate response to spills, leaks, or releases; includingcontainment and cleanup practices to prevent or minimize exposure to people, properties, or the

environment.Personal Precautions: Wear appropriate protective clothing

Emergency Procedure(s):Immediately contain the spill by covering and blocking off the areato prevent spreading.

Method(s) and material(s)used for containment:

The spilled chemical will be contained by covering and blockingoff the area. Then the chemical will be scooped up into bags orcontainers and disposed of in accordance with Section 13 of thisSDS.

Cleanup procedure(s): Contain, collect and place in suitable container for reuse or disposal

Section 7: Handling and Storage

Guidance on the safe handling practices and conditions for safe storage of the chemical.

Handling precautions:Store in cool dry ventilated area, prevent accumulation of dust. Storeaway from oxidizing agents, wear impervious gloves, safety glasseswith side shield, NIOSH approved dust respirator

Hygiene practices: Wear appropriate protective clothing and complete ordinary hygienepractices

Safe storage recommendation: Store in cool, dry, ventilated area.Incompatible storage options: Excessive heat and strong oxidizers

Page 4: Sds - Anco Micro Blend

7/26/2019 Sds - Anco Micro Blend

http://slidepdf.com/reader/full/sds-anco-micro-blend 4/7

Section 8: Exposure Controls/Personal Protection

Identification of the exposure limits, engineering controls, and personal protective measures thatcan be used to minimize worker exposure.

OSHA PermissibleExposure Limits (PELs):

Not a health hazard as defined by OSHA

American Conference of GovernmentalIndustrial Hygienists (ACGIH)Threshold Limit Values (TLVs):

Not listed

Exposure limit (recommended bymanufacturer, importer or employer):

N/A

Appropriate Engineering Controls:

Local and/or general exhaust if handled in a confinedarea, wear impervious gloves, safety glasses with sideshield, NIOSH approved dust respirator, and an eyewash station and safety shower should be readilyavailable

Recommendations forpersonal protective measures:

Wear appropriate protective clothing

Special requirements of PPE,protective clothing or respirators:

Impervious gloves and safety glasses with side shield

Section 9: Physical and Chemical Properties

Identification of physical and chemical properties associated with the substance or mixture.Appearance (Physical State): PowderColor: Dark BrownOdor: Odorless

Odor Threshold: Not regulatedVapor Pressure: N/AVapor Density: 22LBS/CU FT

pH: 5-7Relative Density: N/A

Melting Point: N/AFreezing Point: N/ASolubility(ies): INSOLUBLEInitial Boiling Point: N/ABoiling Range: N/AFlash Point: N/AEvaporation Rate: N/A

Flammability: FLAMMABLEUpper/lower flammability or

explosive limits:

N/A

Partition Coefficient: N/A

Auto-Ignition Temperature: N/ADecomposition Temperature: N/AViscosity: N/A

Page 5: Sds - Anco Micro Blend

7/26/2019 Sds - Anco Micro Blend

http://slidepdf.com/reader/full/sds-anco-micro-blend 5/7

Section 10: Stability and Reactivity

Description of the reactivity hazards of the chemical and the chemical stability information.Reactivity

Description ofspecific test data:

None

Chemical StabilityIs the chemical stable or unstable: StableStabilizers needed tomaintain chemical stability:

None

Safety issues that may ariseshould the chemical changein physical appearance:

None known

OtherConditions in which hazardousreactions may occur:

Dust may be explosive in the finely divided and suspendedstate and exposed to ignition source.

Possibility of hazardous reactions: PossibleWill chemical react or polymerize: NoWill chemical release pressure, heat,or any other hazardous conditions:

Possible explosion of dust particles

Conditions to avoid: Storing near excessive heat and strong oxidizersClass(es) of incompatible material(s): Strong OxidizersKnown or anticipated hazardousdecomposition products producedbecause of storage, use, or heating:

None known

Section 11: Toxicological Information

Identification of toxicological and/or health effects.Likely routes of exposure: Inhalation, Skin, Ingestion, OcularDelayed, immediate or chroniceffects of short-term exposure:

Irritation

Delayed, immediate or chroniceffects of long-term exposure:

Possible Irritation

Numerical measurement of toxicity: Health: 1, Flammability: 0, Reactivity: 0Description of symptoms(lowest to most severe):

Irritation to Advanced Irritation

Is chemical listed in the National ToxicologyProgram (NTP) Report on Carcinogens:

No

Has chemical been found to be a potential carcinogen in theInternational Agency for Research on Cancer (IARC) Monographs:

No

Has chemical been found to be a potential carcinogen by OSHA: No

Page 6: Sds - Anco Micro Blend

7/26/2019 Sds - Anco Micro Blend

http://slidepdf.com/reader/full/sds-anco-micro-blend 6/7

Section 12: Ecological Information (non-mandatory)

Information to evaluate the environmental impact of the chemical if it were released to theenvironment.

Toxicity test results performed onaquatic and/or terrestrial organisms:

None

Does the chemical have the potential todegrade the environment (biodegradation,oxidation, hydrolysis, etc.):

No

Bioaccumulation test results: NonePotential of chemical movingfrom soil to the groundwater:

Low probability. Product cannot penetrate soil to reachgroundwater

Other adverse effects: None known

Section 13: Disposal Considerations (non-mandatory)

Guidance on proper disposal practices, recycling or reclamation of the chemical or its container.Safe handling practices to minimize exposure. (Refer to section 8 for more information)

Appropriate disposal containers: Original container or container that is in accordance tolocal, state and federal regulations

Appropriate disposal methods:Dispose of in accordance to local, state and federalregulations

Physical and chemical propertiesthat may affect disposal activities:

Prevent dust accumulation and storage near oxidizingagents

Special precautions for landfillsor incineration activities:

Prevent dust accumulation and storage near oxidizingagents

Is it advisable to utilize sewagedisposal for this chemical:

No

Section 14: Transport Information (non-mandatory)Guidance on classification information for shipping and transporting the chemical by road, air,

rail, or sea.

This is not a DOT/IMO Regulated Material

Page 7: Sds - Anco Micro Blend

7/26/2019 Sds - Anco Micro Blend

http://slidepdf.com/reader/full/sds-anco-micro-blend 7/7

Section 15: Regulatory Information (non-mandatory)

Identification of safety, health and environmental regulations specific for the chemical that is notindicated anywhere else on this SDS.

Chemical Weapons Convention (CWC): This product does not contain any chemicals listedunder the CWC schedules of chemicals.

Clean Air Act - Hazardous Air Pollutants (HAP): This product does not contain any chemicalslisted within the Hazardous Air Pollutants.Clean Air Act - Ozone Depleting Substances (ODS): This product neither contains, nor wasmanufactured with a Class I or Class II ODS as defined by the U.S. Clean Air Act Section 602(40 CFR 82, Subpart A, App. A+B).Clean Water Act - Priority Pollutants (PP): This product does not contain any PP listed underthe U.S. Clean Water Act, Section 307 (2)(1) PP List (40 CFR 401.15).Occupational Safety and Health Act (OSHA): The OSHA Hazard Communication Standard(29 CFR 1910.1200) defines this product as C.4.1, C.4.2 & C.4.3 Acute Toxicity - Oral, Dermal& Inhalation: Hazard Category 3. For more information, see Section 2 of this SDS.Resource Conservation and Recovery Act (RCRA): This product is not considered to be a P-or U-Listed hazardous waste under RCRA (40 CFR 261).

Superfund Amendments and Reauthorization Act (SARA) Title III: Section 302 - ExtremelyHazardous Substances (EHS): This product does not contain any chemicals regulated underSection 302 (40 CFR 355) as extremely hazardous substances.Superfund Amendments and Reauthorization Act (SARA) Title III: Section 304 -Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA):This product does not contain any chemicals regulated under Section 304 (40 CFR 302) ashazardous substance(s) for emergency release notification.Superfund Amendments and Reauthorization Act (SARA) Title III: Section 311/312 -Hazard Communication Standard (HCS): This product is not regulated under Section 3-1-312(40 CFR 370).Superfund Amendments and Reauthorization Act (SARA) Title III: Section 313 ToxicChemical List (TCL): This product does not contain any chemicals for routine annual toxic

chemical release reporting under Section 313 (40 CFR 372).” TSCA Section 5(e) - Consent Order / Significant New Use Rule (SNUR):  This product is notsubject to a Section 5(3) Consent Order for Significant New Use Rule (SNUR).TSCA Section 8(b) - Inventory Status: All chemical(s) comprising this product are eitherexempt or not listed on the TSCA inventory.TSCA Section 12(b) - Export Notification: This product does not contain any chemical(s) thatare subject to a Section 12(b) export notification.

Items in red require immediate attention.

Section 16: Other Information

Date of SDS Preparation: October 7, 2013

Revision Date: N/AChanges from previous version: N/A

Other useful information: N/A

We believe the statements, technical information and recommendations contained herein are reliable, but they aregiven without warranty or guarantee of any kind, expressed or implied, and we assume no responsibility for any

damage or expense.