8/13/2019 Sikagard 676W
1/2
Product Data SheetEdition 11, 2006Version no. 01.03
Sikagard- 676W 1/2
Co
nstruct
ion
Sikagard -676W
Fungicidal Wall Paint for Wet Areas
ProductDescription
Fungicidal, colour, one-pack emulsion paint.
Uses For painting concrete and rendering, especially in places
sensitive to fungal attack,e.g. rooms in waterworks, breweries,
wine cellars and textile factories.
Advantages Fungicidal.Good adhesion in damp
conditions.Condensation resistant.
Product DataColour RAL 1013, oyster white.Packaging 17.5
ltr.Shelf life Use as soon as possible; max. 12 months. Like all
substances containing water,
Sikagard-676W is susceptible to frost. Delivery only at
above-zero temperatures.Store protected from frost!
Technical DataDensity Liquid: approx. 1.38 g/ml.
Solid: approx. 1.80 g/ml.Solids % by weight: approx. 64%
% by volume: approx. 50%
Resistance Sikagard-676W is waterproof and weatherproof; also
resistant to dilute acids and
alkalis, chemically aggressive environments, animal and
vegetable oils and fats.Not resistant to concentrated acids,
alkalis and hot water.
Appl icat ionCoating System/Material Consumption
For normal duty:2 x Sikagard
-676W.
Thin first (priming) coat, adding 5 10% water depending on
condition of substrate.For heavy duty (exposure to chemicals,
water):3 x Sikagard
-676W.
Here too, thin first coat.Priming coat:For smooth rendering and
prewetted surfaces, approx. 0.12 0.20 ltr./m
2.
Top coat:Approx. 0.20 0.25 ltr./m
2per coat.
The requirement may be considerably higher for rough-textured
rendering orconcrete. Do not apply inside water reservoirs.
Condition of Substrate Free from dust, with sufficient strength
and key, stripped of residual paint.Substrate Preparation Do not
apply Sikagard
-676W to concrete or rendering younger than 28 days. Any
concrete or cementitious rendering must be cured and air-dry
(this usually takesmax. 4 weeks.) non-hydraulic lime plaster must
be fully cured prior to painting (thiscan take up to half a
year).
Abrade old, tightly adhering coatis, e.g. oil paints, and prime
with thinnedSikagard-676W.
Roughen smooth coats of oil paint, e.g. on timber, by prior
washing with ammoniumchloride solution or by abrading.
8/13/2019 Sikagard 676W
2/2
Sikagard- 676W 2/2
Co
nstruct
ion
Appl icationAppl icationAmbient and Subst rateTemperature
Ambient and Subst rateTemperature
Min. + 8CMin. + 8CMax. + 30CMax. + 30C
Appl ication Method The material is supplied ready to use; stir
well prior to application.Brush application:Best using ceiling
brush or bridled round brush.Roller application:Lambskin
roller.Spray application:Airless spraying unit, approx. 200 bar,
nozzle size 0.38 0.48 mm spraying angle60
Cleaning of Implements Water.+10C +20C +30C
Sikagard-676W 8 hours 5 hours 1 hour
Waiting Time betweenCoats
Efficient ventilation provided.Final Drying Time The coat may
seem to be properly dry if no paint comes off, when rubbed with a
wet
finger. The dry coat should cure for at least another two days
prior to exposure towater; ensure adequate level of air exchange,
particularly in deep locations.
Safety Instruct ionsEcology Remnants of the not fully cured
product must be disposed of according to law. Fully
cured material can be disposed of as household waste according
to localregulations.
Safety Precautions The provisions or the dangerous goods
regulations must be observed.During application observe hints on
labels as well as local regulations.In a liquid state the product
contaminates water and should not get into drains,
water or ground.Further details are contained in our
instructions Health protection and prevention ofaccidents.
Legal notes The information, and in particular, the
recommendations relating to the application and end-use ofSika
products, are given in good faith based on Sika's current knowledge
and experience of the products
when properly stored, handled and applied under normal
conditions in accordance with
Sikas recommendations. In practice, the differences in
materials, substrates and actual site conditions are
such that no warranty in respect of merchantability or of
fitness for a particular purpose, nor any liability
arising out of any legal relationship whatsoever, can be
inferred either from this information, or from any
written recommendations, or from any other advice offered. The
user of the product must test the products
suitability for the intended application and purpose. Sika
reserves the right to change the properties of its
products. The proprietary rights of third parties must be
observed. All orders are accepted subject to our
current terms of sale and delivery. Users must always refer to
the most recent issue of the local Product
Data Sheet for the product concerned, copies of which will be
supplied on request.
Sika Egypt for Construction ChemicalsEl Abour City1
stindustrial zone (A)
Section # 10 Block 13035,Egypt
Tel :+202- 6100714/15/16/17/18Fax :+202- 6100759Mob :+2012-
3908822/55www.sika.com.eg
