sony hcd-shake33 hcd-shake77 ver1.0 sm

8/18/2019 sony hcd-shake33 hcd-shake77 ver1.0 sm

1/120

SERVICE MANUAL

Sony CorporationPublished by Sony EMCS (Malaysia) PG Tec

HCD-SHAKE33/SHAKE77

HOME AUDIO SYSTEM9-890-648-012014A80-1

© 2014.01

US Model AEP Model

UK Model HCD-SHAKE33

E Model HCD-SHAKE33/SHAKE77

Australian Model HCD-SHAKE77

Ver. 1.0 2014.01

• HCD-SHAKE33 is the tuner, USB, CDplayer, Bluetooth, NFC and amplifiersection in SHAKE-33.

• HCD-SHAKE77 is the tuner, USB, CDplayer, Bluetooth, NFC and amplifiersection in SHAKE-77.

SPECIFICATIONS

CD Section

Model Name Using Similar Mechanism NEW

CD Mechanism Type CDM90-DVBU202//M

Optical Pick-up Name CMS-S76RFS7G

Photo: HCD-SHAKE77

– Continued on next page –

, USB, CD

AUDIO POWER SPECIFICATIONSPOWER OUTPUT AND TOTAL HARMONICDISTORTION:(US model only)

SHAKE-33With 4 ohm loads, both channels driven, from

40 – 600 Hz; rated 180 watts per channelminimum RMS power, with no more than

0.7% total harmonic distortion from 250milliwatts to rated output.

Amplifier sectionThe following are measured at

US model: AC 120 V, 60 Hz

MX model: AC 120 V – 240 V, 60 Hz

AEP, UK model: AC 220 V – 240 V, 50/60 Hz

E51 model: AC 220 V – 240 V, 50 Hz

Other models: AC 120 V – 240 V, 50/60 Hz

SHAKE-77WF (Woofers)/MID (Mid speakers)/

TW (Tweeters) Power Output (rated):

350 W + 350 W (at 4 ohms, 1 kHz, 1% THD)

RMS output power (reference): 600 W + 600 W (per channel at

4 ohms, 1 kHz)SW (Subwoofers)

RMS output power (reference):

1,200 W + 1,200 W (per channel at 8 ohms, 100 Hz)

SHAKE-33WOOFERS Power Output (rated):

350 W + 350 W (at 4 ohms, 100 Hz, 1% THD)

RMS output power (reference): 600 W + 600 W (per channel at

4 ohms, 100 Hz)MID (Mid speakers)/TWEETERS

RMS output power (reference):

500 W + 500 W (per channel at 5 ohms, 1 kHz)

InputsAUDIO IN 1/PARTY CHAIN IN L/R

Voltage 2 V, impedance 47 kilohmsAUDIO IN 2 L/R

Voltage 2 V, impedance 47 kilohmsMIC (SHAKE-77 only)

Sensitivity 1 mV, impedance 10 kilohms (USB) A, (USB) B port

Type A

OutputsAUDIO OUT/PARTY CHAIN OUT L/R

Voltage 2 V, impedance 1 kilohm

USB sectionSupported bit rate

WMA: 48 kbps – 192 kbps, VBR, CBR

AAC:

48 kbps – 320 kbps, VBR, CBRSampling frequencies

WMA: 44.1 kHz AAC: 44.1 kHz

Supported USB device Mass Storage Class

Maximum current 500 mA

Disc/USB sectionSupported bit rate MPEG1 Layer-3:

32 kbps – 320 kbps, VBR

MPEG2 Layer-3: 8 kbps – 160 kbps, VBR

MPEG1 Layer-2: 32 kbps – 384 kbps, VBR

Sampling frequencies MPEG1 Layer-3:

32 kHz/44.1 kHz/48 kHz MPEG2 Layer-3:

16 kHz/22.05 kHz/24 kHz MPEG1 Layer-2:

32 kHz/44.1 kHz/48 kHz

Disc player sectionSystem

Compact disc and digital audio systemLaser Diode Properties

Emission Duration: Continuous

Laser Output*: Less than 44.6 µW * This output is the value

measurement at a distance of200 mm from the objective lens

surface on the Optical Pick-upBlock with 7 mm aperture.

Frequency response 20 Hz – 20 kHz

Signal-to-noise ratio More than 90 dB

Dynamic range More than 88 dB

Tuner sectionFM stereo, FM/AM superheterodyne tuner

Antenna: FM lead antenna

AM loop antenna

FM tuner sectionTuning range

US model:

87.5 MHz – 108.0 MHz (100 kHz step) Other models:

87.5 MHz – 108.0 MHz (50 kHz step)

AM tuner sectionTuning range AEP, UK model:

531 kHz – 1,602 kHz (9 kHz step) AUS, E2, E51, US, MX models:

531 kHz – 1,710 kHz (9 kHz step) 530 kHz – 1,710 kHz (10 kHz step)

Other models: 531 kHz – 1,602 kHz (9 kHz step)

530 kHz – 1,610 kHz (10 kHz step)

Bluetooth sectionCommunication system

Blue toot h Standard version 3.1Output

Blue toot h Standard Power Class 2Maximum communication range

Line of sight approx. 10m1)

Frequency band

2.4 GHz band (2.4000 GHz – 2.4835 GHz)

Modulation method

FHSS (Freq Hopping Spread Spectrum)Compatible Bluet ooth profiles2)

A2DP (Advanced Audio Distribution Profile)

AVRCP 1.3 (Audio Video Remote Control Profile)

SPP (Serial Port Profile)Supported codecs

SBC (Sub Band Codec) AAC (Advanced Audio Coding)

1) The actual range will vary depending onfactors such as obstacles between devices,

magnetic fields around a microwave oven,static electricity, reception sensitivity,

antenna’s performance, operating system,software application, etc.

2) Blue tooth standard profiles indicate thepurpose of Blue tooth communication

between devices.


2/120

HCD-SHAKE33/SHAKE77

2

SAFETY CHECK-OUTAfter correcting the original service problem, perform the following

safety check before releasing the set to the customer:

Check the antenna terminals, metal trim, “metallized” knobs,

screws, and all other exposed metal parts for AC leakage. Check

leakage as described below.

LEAKAGE TEST

The AC leakage from any exposed metal part to earth ground andfrom all exposed metal parts to any exposed metal part having a

return to chassis, must not exceed 0.5 mA (500 microamperes).

Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or RCA

WT-540A. Follow the manufacturers’ instructions to use these

instruments.

2. A battery-operated AC milliammeter. The Data Precision 245

digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of a

VOM or battery-operated AC voltmeter. The “limit” indication

is 0.75 V, so analog meters must have an accurate low-voltage

scale. The Simpson 250 and Sanwa SH-63Trd are examples

of a passive VOM that is suitable. Nearly all battery operated

digital multimeters that have a 2V AC range are suitable. (See

Fig. A)

1.5 k Ÿ0.15 —F AC voltmeter (0.75 V)

To Exposed Metal Parts on Set

Earth Ground

Fig. A. Using an AC voltmeter to check AC leakage.

License and Trademark Notice

• “WALKMAN” and “WALKMAN” logo are registered trademarks of

Sony Corporation.

• MPEG Layer-3 audio coding technology and patents licensed from

Fraunhofer IIS and Thomson.

• Windows Media is either a registered trademark or trademark of

Microsoft Corporation in the United States and/or other countries.

• This product is protected by certain intellectual property rights of

Microsoft Corporation. Use or distribution of such technology outside

of this product is prohibited without a license from Microsoft or an

authorized Microsoft subsidiary.

• The Bluetooth® word mark and logos are registered trademarks

owned by Bluetooth SIG, Inc. and any use of such marks by Sony

Corporation is under license. Other trademarks and trade names are

those of their respective owners.

• The N Mark is a trademark or registered trademark of NFC Forum,

Inc. in the United States and in other countries.

• Android™ is a trademark of Google Inc.

• Google Play™ is a trademark of Google Inc.

• iPhone and iPod touch are trademarks of Apple Inc., registered in the

U.S. and other countries. App Store is a service mark of Apple Inc.

• “Made for iPod” and “Made for iPhone” mean that an electronic

accessory has been designed to connect specifically to iPod or iPhone,

respectively, and has been certified by the developer to meet Apple

performance standards. Apple is not responsible for the operation of

this device or its compliance with safety and regulatory standards.

Please note that the use of this accessory with iPod or iPhone may

affect wireless performance.

• All other trademarks and registered trademarks are of their respective

holders. In this manual, ™ and ® marks are not specified.

• Abbreviation AUS : Australian model E2 : 120 V AC area in E model E51 : Chilean and Peruvian models MX : Mexican model

SAFETY-RELATED COMPONENT WARNING!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTSWHOSE PART NUMBERS APPEAR AS SHOWN IN THISMANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORTÀ LA SÉCURITÉ!

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SURLES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DESPIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-TIONNEMENT. NE REMPLACER CES COMPOSANTS QUEPAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTSPUBLIÉS PAR SONY.


3/120

HCD-SHAKE33/SHAKE77

3

1. SERVICING NOTES ............................................. 4

2. DISASSEMBLY2-1. Overall Case .................................................................... 10

2-2. Back Panel Section ......................................................... 11

2-3. Loading Panel Assy ........................................................ 11

2-4. CDM90-DVBU202//M ................................................... 122-5. Front Panel Section ......................................................... 13

2-6. MOTHERBOARD Board ............................................... 13

2-7. 4CH DAMP Board (SHAKE33),

6CH DAMP Board (SHAKE77) ..................................... 14

2-8. REGULATOR, SWITCHING (3H401W) (SHAKE33),

SWITCHING REGULATOR (SSN-GBR)

(SHAKE77) .................................................................... 15

2-9. Service Optical Device, Wire (Flat Type) ....................... 16

3. TEST MODE ............................................................ 17

4. ELECTRICAL CHECK ......................................... 21

5. TROUBLESHOOTING .......................................... 22

6. DIAGRAMS6-1. Block Diagram - RS SERVO, USB Section - ................. 31

6-2. Block Diagram - MAIN Section - ................................... 32

6-3. Block Diagram - AMP Section (SHAKE33) - ................ 33

6-4. Block Diagram - AMP Section (SHAKE77) - ................ 34

6-5. Block Diagram

- PANEL, POWER SUPPLY Section - ......... .......... ........ 35

6-6. Printed Wiring Board

- MOTHERBOARD Board (Component Side) - ............ 37


- MOTHERBOARD Board (Conductor Side) - ............. 38

6-8. Schematic Diagram

- MOTHERBOARD Board (1/8) - ................................. 39

6-9. Schematic Diagram - MOTHERBOARD Board (2/8) - ................................. 40














- 4CH DAMP Board (SHAKE33) - ................................ 476-17. Schematic Diagram

- 4CH DAMP Board (SHAKE33) (1/2) - ....................... 48



6-19. Printed Wiring Board - 6CH DAMP Board (SHAKE77)

(Component Side) - ......................................................... 50

6-20. Printed Wiring Board - 6CH DAMP Board (SHAKE77)

(Conductor Side) - .......................................................... 51







TABLE OF CONTENTS

6-24. Printed Wiring Board - STR Board (SHAKE33) - ......... 556-25. Schematic Diagram - STR Board (SHAKE33) - ............ 566-26. Printed Wiring Board - STR Board (SHAKE77) (Component Side) - ......................................................... 57

6-27. Printed Wiring Board - STR Board (SHAKE77)

(Conductor Side) - .......................................................... 586-28. Schematic Diagram - STR Board (SHAKE77) - ............ 596-29. Printed Wiring Board - FL Board (SHAKE33) - ............ 606-30. Schematic Diagram - FL Board (SHAKE33) - ............... 616-31. Printed Wiring Board - FL Board (SHAKE77) (Component Side) - ......................................................... 62

6-32. Printed Wiring Board - FL Board (SHAKE77) (Conductor Side) - .......................................................... 63

6-33. Schematic Diagram - FL Board (SHAKE77) - ............... 646-34. Printed Wiring Board - MIC Board (SHAKE33) - ......... 656-35. Schematic Diagram - MIC Board (SHAKE33) - ............ 666-36. Printed Wiring Board - MIC Board (SHAKE77) - ......... 676-37. Schematic Diagram - MIC Board (SHAKE77) - ............ 686-38. Printed Wiring Board - TUNER Board - ........................ 69

6-39. Schematic Diagram - TUNER Board - ........................... 70

7. EXPLODED VIEWS7-1. Overall Case Section ....................................................... 84

7-2. Back Panel Section ......................................................... 85

7-3. FL Board, STR Board ..................................................... 86

7-4. Front Panel Section ......................................................... 87

7-5. MOTHERBOARD Board Section .................................. 88

7-6. Chassis Section ............................................................... 89

7-7. CD Mechanism Section (CDM90-DVBU202//M) ......... 90

8. ELECTRICAL PARTS LIST .............................. 91


4/120

HCD-SHAKE33/SHAKE77

4

SECTION 1SERVICING NOTES

Notes on chip component replacement

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270 °C

during repairing.

• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

UNLEADED SOLDER

Boards requiring use of unleaded solder are printed with the

leadfree mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40 °C higher

than ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350 °C.

Caution: The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow)

than ordinary solder so use caution not to let solder bridges

occur such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

CAUTION

Use of controls or adjustments or performance of proceduresother than those specified herein may result in hazardous radiation

exposure.

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK

OR BASE UNIT

The laser diode in the optical pick-up block may suffer electrostatic

break-down because of the potential difference generated by the

charged electrostatic load, etc. on clothing and the human body.

During repair, pay attention to electrostatic break-down and also

use the procedure in the printed matter which is included in the

repair parts.

The flexible board is easily damaged and should be handled with

care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused

on the disc reflective surface by the objective lens in the optical

pickup block. Therefore, when checking the laser diode emission,

observe from more than 30 cm away from the objective lens.

This appliance is classified as a CLASS 1 LASER product. This

marking is located on the rear exterior.

MODEL IDENTIFICATION

- BACK PANEL -

Model Part No.

HCD-SHAKE77 : E2, E51, AUS 4-479-323-0[]

HCD-SHAKE77 : MX 4-479-323-2[]

HCD-SHAKE33 : E2, E51 4-479-422-0[]

HCD-SHAKE33 : US 4-479-422-1[]

HCD-SHAKE33 : MX 4-479-422-2[]

HCD-SHAKE33 : AEP, UK 4-479-422-3[]

• Abbreviation

AUS : Australian model E2 : 120 V AC area in E model E51 : Chilean and Peruvian models MX : Mexican model

PLAYABLE DISCS

• AUDIO CD

• CD-R/CD-RW

– audio data

– MP3 files that conforms to ISO9660 Level 1/Level 2, or

Joliet (expansion format).

Notes

• MP3 (MPEG 1 Audio Layer-3) is a standard format defined

by ISO (International Organization for Standardization) which

compresses audio data. MP3 files must be in MPEG 1 Audio

Layer-3 format.• The system can only play back MP3 files that have a file

extension of “.mp3”.

PART No.


5/120

HCD-SHAKE33/SHAKE77

5

NOTE OF REPLACING THE IC001, IC002, IC106,

IC302 AND IC306 ON THE MOTHERBOARD BOARD

IC001, IC002, IC106, IC302 and IC306 on the MOTHERBOARD

board cannot exchange with single. When these parts on the

MOTHERBOARD board are damaged, exchange the entire

mounted board.

NOTE OF REPLACEMENT OF THE MS-476 BOARD

When the MS-476 board is defective, exchange the entireLOADING COMPLETE ASSY (T).

RELEASING THE DISC TRAY LOCK

The disc tray lock function for the antitheft of an demonstration

disc in the store is equipped.

Releasing Procedure:

1. Press [\ / 1] button to turn the power on.

2. Press the [CD] button to select CD function.

3. Press the [x] button and [n / +] button simultaneously and

hold down for around 5 seconds.

4. The message “UNLOCKED” is displayed and the disc tray is

unlocked.

Note: When “LOCKED” is displayed, the slot lock is not released byturning power on/off with the [\ / 1] button.

NOTE OF DISASSEMBLE THE CASE, OVERALL

To disassemble the CASE, OVERALL, hexagon key is required to

unscrew the SCREW, TAPPING (HEX).

NOTE OF REPLACING MOTHERBOARD BOARD OR

BLUETOOTH MODULE OR RC-S801/A (WW) BOARD

When the MOTHERBOARD board or BLUETOOTH module or

RC-S801/A (WW) board are replaced, please execute the below

service mode.

Pairing this system with a Bluetooth device

1. Press the [\ / 1] button to turn the power on.2. Place the Bluetooth device within 1 meter (3 feet) from the

system.

3. Press BLUETOOTH on the unit to select Bluetooth function.

“BLUETOOTH” appears in the display panel.

4. Hold down BLUETOOTH on the unit for 2 seconds or more.

“PAIRING” flashes in the display panel.

5. Perform the pairing procedure on the Bluetooth device.

6. Select the model number of the unit on the display of the

Bluetooth device.

For example, select “SONY : SHAKE-77/SHAKE-33”. If

passkey is required on the Bluetooth device, enter “0000”.

7. Perform the Bluetooth connection on the Bluetooth device.

8. When pairing is completed and the Bluetooth connection is

established, the Bluetooth device name appears in the display

panel.9. To cancel pairing operation, hold down BLUETOOTH on the

unit for 2 seconds or more until “BLUETOOTH” appears in

the display panel.

Connecting with a smartphone by one touch (NFC)

Note: The operation in this mode must use a NFC-compatible smartphone(Smartphones with a built-in NFC function [OS: Android 2.3.3 or

later, excluding Android 3.x])

1. Press the [\ / 1] button to turn the power on.

2. Download and install the app “NFC Easy Connect”.

Download the free Android app from Google Play by searching

for “NFC Easy Connect”.

3. Start the app “NFC Easy Connect” on the smartphone.

Make sure that the application screen is displayed.4. Touch the smartphone to the N-Mark on the system until the

smartphone vibrates.

Complete the connection by following the instructions

displayed on the smartphone.

5. When pairing is completed and the Bluetooth connection is

established, the Bluetooth device name appears in the display

panel.

hexagon key

hexagon key


6/120

HCD-SHAKE33/SHAKE77

6

Playing music from a Bluetooth device

For a Bluetooth device


2. Press BLUETOOTH on the unit to select Bluetooth function.


3. Establish connection with the Bluetooth device.

Press BLUETOOTH on the unit to connect to the last

connected Bluetooth device.

Perform the Bluetooth connection from the Bluetooth device if

the device is not connected.

Once the connection is established, the Bluetooth device name

appears in the display panel.

4. PressN. Depending on the Bluetooth device,

– you may have to pressN twice. – you may need to start playback of an audio source on the

Bluetooth device.

For an NFC-compatible smartphone


Touch the smartphone to the N-Mark on the system to establish

the Bluetooth

connection. Start playback of an audio source on the smartphone. For

details on playback, refer to the operating instructions of your

smartphone.

To disconnect the Bluetooth deviceFor a Bluetooth device

Press BLUETOOTH on the unit.


For an NFC-compatible smartphone

Touch the smartphone to the N-Mark on the system again.

To erase all the pairing registration information perform

COLD RESET test mode (Refer page 18).


7/120

HCD-SHAKE33/SHAKE77

7

HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFFNote 1: After the case overall is removed, this word is done.

Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).

2 Insert the clip etc.

3

tray

tray

Insert the clip etc.processed to thelength of 8 cm ormore in the holeon the side of the

chassis and push.

8 cm or more

hole

– Side view –

– Top view –

Note: Push after it inserts it in this hole well.

CD drive

1 Remove the case, overall. (Illustration of disassembly is omitted.)

CAPACITOR DISCHARGE FOR ELECTRIC SHOCK PREVENTION

Switching Regulator Board (Conductor side view) (HCD-SHAKE33)

In checking the Switching Regulator board, make 3 capacitors discharge of C221, C602 and C618 for eletrical shock prevention.

800 : /5 W 800 : /5 W

800 : /5 W

C602

C618

C221


8/120

HCD-SHAKE33/SHAKE77

8

Switching Regulator Board (Conductor side view) (HCD-SHAKE77)

In checking the Switching Regulator board, make 3 capacitors discharge of C20, C28 and C18 for eletrical shock prevention.

800 : /5 W

C20 C28

C18

800 : /5 W

800 : /5 W

PRECAUTION WHEN INSTALLING A NEW OP UNIT/PRECAUTION BEFORE UNSOLDERING THE STATIC

ELECTRICITY PREVENTION SOLDER BRIDGE (CDM90-DVBU202//M)

When installing a new OP unit, be sure to connect the flexible printed circuit board first of all before removing the static electricity

prevention solder bridge by unsoldering.

Remove the static electricity prevention solder bridge by unsoldering after the flexible printed circuit board has already been connected.

(Do not remove nor unsolder the solder bridge as long as the OP unit is kept standalone.)


9/120

HCD-SHAKE33/SHAKE77

9

2-2. BACK PANEL SECTION (Page 11)

2-3. LOADING PANEL ASSY (Page 11)

2-4. CDM90-DVBU202//M (Page 12)

2-5. FRONT PANEL SECTION (Page 13)

2-6. MOTHERBOARD BOARD (Page 13)

2-7. 4CH DAMP BOARD (SHAKE33), 6CH DAMP BOARD (SHAKE77) (Page 14)

2-1. OVERALL CASE (Page 10)

2-8. REGULATOR, SWITCHING (3H401W) (SHAKE33), SWITCHING REGULATOR (SSN-GBR) (SHAKE77) (Page 15)

2-9. SERVICE OPTICAL DEVICE, WIRE (FLAT TYPE) (Page 16)

SET

Note: Disassemble the unit in the order as shown below.

SECTION 2DISASSEMBLY


10/120

HCD-SHAKE33/SHAKE77

10

Note: Follow the disassembly procedure in the numerical order given.

2-1. OVERALL CASE

Note: To disassemble the CASE, OVERALL, allen keyis required to unscrew the SCREW, TAPPING (HEX).

4 protector, rear R

8

5 seven screws (+BVTP 3 u 8) (BLACK)

3 protector, rear L

1 four screws (+BVTP 3 u 8) (BLACK)

2 two screws (+BVTP 3 u 8) (BLACK)

6 three screws (tapping (HEX))

9 case, overall

7 three screws (tapping (HEX))


11/120

HCD-SHAKE33/SHAKE77

11

2-2. BACK PANEL SECTION

2-3. LOADING PANEL ASSY

1 Insert the clip etc.

3 three claws

4 panel, loading assy

2

tray

Insert the clip etc.

processed to thelength of 8 cm ormore in the holeon the side of thechassis and push.

8 cm or more

hole

– Side view –

– Top view –

Note: Push after it inserts it in this hole well.

CD drive

1 CN1002 (3P) (SHAKE77) CN1003 (3P) (SHAKE33)



5 three screws (+BVTP 3 u 8) (BLACK)

7

9 back panel section

2 wire (flat type) (9 core) (CN851)

6 four screws (+BVTP 3 u 8) (BLACK)

‡ :LUH VHWWLQJ

rear side 6CH DAMP board

MOTHERBOARD board


12/120

HCD-SHAKE33/SHAKE77

12

2-4. CDM90-DVBU202//M

0 two screws

(+BVTP 3 u 8)

qs bracket, CDM (M7)

6 four screws

(+BVTP 3 u 8)

1 CN401 (6P)

4 CN451 (10P)

2 wire (flat type) (5 core)

(CN303)


(CN302)

qa two screws

(+BVTP 3 u 8)

Note: When you install the CD drive (CDM90-DVBU202//M), please match the position of the boss two places.

7 boss

8

9 CDM90-DVBU202//M

‡ :LUH VHWWLQJ

rear side

MOTHERBOARD board

CDM90-DVBU202//M

‡ :LUH VHWWLQJ front side

bracket, tunnel CDM90-DVBU202//M

5 CN601 (4P)

(SHAKE77)


13/120

HCD-SHAKE33/SHAKE77

13

2-5. FRONT PANEL SECTION

2-6. MOTHERBOARD BOARD

3 five screws (+BVTP 3 u 8)4 MOTHERBOARD board

1 CN001 (6P)


4 five screws (+BVTP 3 u 8)

5 one screw

(+PWH 3 u 8 (SUMITITE))


7 front panel section

6




14/120

HCD-SHAKE33/SHAKE77

14

2-7. 4CH DAMP BOARD (SHAKE33), 6CH DAMP BOARD (SHAKE77)

B

B

D

D

DE

E

B

qsqs

‡ :LUH VHWWLQJ

front side

SWITCHING REGULATOR (SSN-GBR)

bracket, tunnel

(M7)

‡ :LUH VHWWLQJ

front side REGULATOR, SWITCHING (3H401W)

bracket,tunnel (M3)

1 CN1001 (2P)

6 CN1000 (10P)

1 CN1001 (2P)

2 two screws (+BVTP 3 u 8)



2 four screws (+BVTP 3 u 8)

0 six screws (+BVTP 3 u 8)

qa 6CH DAMP board

qa 4CH DAMP board


4 bracket, tunnel (M7)

4 bracket, tunnel (M3)

5 DC fan

5 fan, DC

8 thermal sheet 8 sheet, thermal

7 three screws (+PTPWH 2.6 u L (DIA8.0))

7 three screws (+PTPWH 2.6 u L (DIA8.0))

9 heat sink

0 four screws (+BVTP 3 u 8)

9 heat sink (M3)

qd bracket, heat sink (M7)qd bracket, heat sink

C

CC

(SHAKE77)(SHAKE33)


15/120

HCD-SHAKE33/SHAKE77

15

2-8. REGULATOR, SWITCHING (3H401W) (SHAKE33), SWITCHING REGULATOR (SSN-GBR) (SHAKE77)

1 three screws (+BV3 (3-CR))


8 SWITCHING REGULATOR (SSN-GBR)

7 REGULATOR, SWITCHING (3H401W)

3 CN1 (2P)

4

2 chassis, sub (M7)



2 chassis, sub (M7)

5 seven screws (+PWH 3 u 8 (SUMITITE))

5 two screws (+PWH 3 u 8 (SUMITITE))

6 two washer, dia 20.0mm

7 clamp

9 chassis assy (M7)

5 nine screws (+PWH 3 u 8 (SUMITITE))

6 clamp

(SHAKE77)(SHAKE33)

8 chassis assy (M3)

3 CN1 (2P)

4


16/120

HCD-SHAKE33/SHAKE77

16

2-9. SERVICE OPTICAL DEVICE, WIRE (FLAT TYPE)Note 1 : Before disconnecting the wire (flat type) (24 core) of optical pick-up block, solder the short-land.

8 four insulator screws

7 connector

qa insulator

6 belt

3 Insert the thinwire (clip etc.).

5 tray

qs service, optical device

qa insulator

qa insulator

qh

qk wire (flat type)(24 core)

qg tape

1 six claws

4

90

2 chuck holder assy (T)

2 Solder the short-land.

qf wire (flat type) (5 core)

– Bottom view –

loading assy (T)qd base, lo assy

qj holder, FFC

Note 2: When assembling the service optical device, remove the solder of short-land after connecting the wire (flat type) (24 core).

Under the guide

Under the guide (Fold area)

‡ ,QVWDOODWLRQ RI ZLUH IODW W\SH FRUH DQG ZLUH IODW W\SH FRUH

Note: This illustration sees the loading assy (T) from bottom side.


2 Through the hole

3 Through the hole

4

terminal face

loading assy (T)


6 holder, FFC

5 three claws

5 two claws


9 tape


17/120

HCD-SHAKE33/SHAKE77

17

SECTION 3TEST MODE

[PANEL TEST MODE]This mode is used to check the fluorescent indicator tube, LEDs,

keys, [VOLUME/DJ CONTROL] jog, model, destination and

software version.

Procedure:1. Press [OPTIONS] button and [FOOTBALL] button simultane-

ously and hold 3 seconds.

2. All LEDs and segments in fluorescent indicator tube are lighted

up. All RGB LEDs are lighted up in white color.3. When you want to enter to the software version display mode,

press [n / +] button.

The model information appears on the fluorescent indicator

tube.

Press [n / +] button again to view the destination information.

4. During the destination information display, press [n / +]

button. Each time [n / +] button is pressed, the fluorescent

indicator tube shows the version of each category software

in the following sequence: SC, MTK, OPU, UI, PF, SYS,

CD, CDMA, CDMB, ST, TA, TM and return back to model

information display.

5. When [] button is pressed while the version numbers are

being displayed except model and destination, the date of the

software creation appears. When [] button is pressed again,

the display returns to the software version display.6. Press [ Å / p] button, the key check mode is activated.

7. In the key check mode, the fluorescent indicator tube displays

“K 0 V0”.

Each time a button is pressed, “K” value increases. However,

once a button has been pressed, it is no longer taken into

account.

“V” value increases in the manner of 0, 1, 2, 3 ... if [VOLUME/

DJ CONTROL] knob is turned clockwise, or it decreases in the

manner of 0, 9, 8, 7 ... if [VOLUME/DJ CONTROL] knob is

turned counterclockwise.

8. When [ENTER] button is pressed after all LEDs and segments

in fluorescent indicator tube light up, alternate segments in

fluorescent indicator tube and LEDs would light up, all RGB

LEDs would light up in red color. If you press [ENTER]

button again, another half of alternate segments in fluorescentindicator tube and LEDs would light up, all RGB LEDs

would light up in green color. Pressing [ENTER] button again

would cause all segments in fluorescent indicator tube and

LEDs light up, all RGB LEDs would light up in blue color.

Pressing [ENTER] button again would turn off all segments in

fluorescent indicator tube and all LEDs including RGB LEDs.

9. To release from this mode, press the buttons in the same

manner as step 1, or disconnect the power cord.


18/120

HCD-SHAKE33/SHAKE77

18

[USER RESET]The user reset clears all data including preset data stored in the data

flash to initial conditions exclude history mode data.

Procedure:1. Press [\/1] button to turn on the system.

2. Press [] button and [LED COLOR] button simultaneously

for 3 seconds.

3. “RESET” appears on the fluorescent indicator tube. After that,

the fluorescent indicator tube becomes blank for a while, andthe system is reset.

[COLD RESET]The cold reset clears all data including preset data stored in the

data flash to initial conditions included history mode data. Execute

this mode when returning the set to the customer.


2. Press [] button and [OPTIONS] button simultaneously for 3

seconds.

3. “COLD RESET” appears on the fluorescent indicator tube.

After that, the fluorescent indicator tube becomes blank for a

while, and the system is reset.

[CD TRAY LOCK MODE]This mode let you lock the disc tray. When this mode is activated,

the disc tray will not open when [ZOPEN/CLOSE] button ispressed. The message “LOCKED” will be displayed on the

fluorescent indicator tube. This mode only applied when there is

disc(s) on the tray.


2. Select CD function.

3. Press [] button and [n / +] button simultaneously and hold

down until “LOCKED” or “UNLOCKED” displayed on the

fluorescent indicator tube (around 5 seconds).


19/120

HCD-SHAKE33/SHAKE77

19

[HISTORY MODE]This mode is used to check important data stored in the system

when PROTECTOR happen.

Procedure:1. During demo mode, press [OPTIONS] button and [FLANGER]

button for 5 seconds to mode into history mode.

2. Press the [TUNING +/ M > x] button or [TUNING Å / w

. m] button to check history data stored.

To release from History Mode.

To release from this mode, press [\/1] button.

Protect Type Description:

Er ror Code Description

E01 The over current condition to MOSFET occurs

by defect of MOSFET or defect of PS output

line.

E03 Defect of power supply circuit to AMP.

There is possibility of unusual power supply of

any of the AMP IC or Pre-amplifier.

E04 DC appears in SP terminal by defect of AMP

IC and MOSFET

or

Defect of DC FAN and DC FAN driver circuit

E05 Unusual heat up of MOSFET by improper

assembly of heat sink, destruction of MOSFET

etc.

If speaker does not have output even if the set status is not in

PROTECT mode, the following defect might be possible:

Defects Possible cause

RESET defect Reset signal status from micom is not ‘H’.

Display on fluorescent indicator tube Description

P R O C O U N T d d No of time protector happen (0 ~ 99)

P R O T Y P E d d d d Refer to protect type description

T 1 d d d d d H d d MSingle Power On Time until protector happened

(0~99999 hours, 0~99Min)

T 2 d d d d d H d d MTotal Power On Time [ no consider protector happen ]

(0~99999 hours, 0~99Min)

F U N C d d d d d d d Input Function during protector happened

V O L d d d Volume setting (MIN / 1 - 50 / MAX)

A T T d d d Actual attenuation (-87 … 0)

E Q L O W d d d Low EQ level (-6 … 0 … +6)

E Q M I D d d d Mid EQ level (-6 … 0 … +6)

E Q H I G H d d d High EQ level (-6 … 0 … +6)

S U R R d d d Surround setting (OFF / ON)

D J d d d d d d d d

DJ Effect setting

DJ Mode: OFF/ISOLAT/FLANGE/PAN/WAH

DJ Setting Value: 1~ 40

B A Z U C A d d d Bass Bazuca setting (OFF / ON)


20/120

HCD-SHAKE33/SHAKE77

20

[MODEL & DEST WRITE MODE]This mode is used to set software model & destination.This mode only available when no permanent model & destinationis stored.

Procedure:1. Press [MOVIE/GAME] button & [LED PATTERN] button

simultaneously and hold for 5 seconds.

2. Fluorescent indicator tube display will show “M XXXXX”.

3. Press [n /

+] / [

-/ p

] button to select the model based on theset’s model.

Product Code F. Tube display

SHAKE-33 “M MAGMA3”

SHAKE-77 “M MAGMA7”

4. Press [ENTER] button.

5. Fluorescent indicator tube display will show “D XXXXX”.

6. Press [n / +] / [-/ p] button to select the destination based

on the set’s country.

Area Code Country F. Tube display

J1 Japan “D J”

JE1 Tourist “D JE”

U2/CA2 America, Canada “D NA”

CEL/CE1/

CE2

Europe(general) “D CE2”

CEK U.K. “D CEK”

RU1/RU3 Russia “D RU”

AU1 Australia “D AU”

CN1 China “D CN”

E12 India, Pakistan, Morocco “D E12”

E3/E15 Middle East, Iran “D E3”

E4/EA3/

E93/SA2

Saudi Arabia, Africa “D EA3”

HK1/

HK2/PL1/

SP1/SP2/

SP6/TH1

Hong Kong, Philippines,

Singapore, Malaysia,

Thailand

“D ASIA”

KR2 Korea “D KR”

TW2 Taiwan “D TW”

E2, E32,

E51, AR2

Latin America(general),

Chile, Peru, Argentina

“D LATIN”

BR1 Brazil “D BR”

MX2,

MX4

Mexico “D MX”

7. Press [ENTER] button to confirm the selection.

8. “RESET” appears on the fluorescent indicator tube. After that,

the fluorescent indicator tube becomes blank for a while, and

the system is reset.

9. Mode in [PANEL TEST MODE] again to confirm on the

model & destination.


21/120

HCD-SHAKE33/SHAKE77

21

SECTION 4ELECTRICAL CHECK

Procedure:1. Turn the power on.

2. Input the following signal from Signal Generator to FM

antenna input directly.

Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz

Deviation : 75 kHz

Modulation : 1 kHz

ANT input : 35 dBu (EMF)

Note: Please use 75 ohm “coaxial cable” to connect SG and theset. You cannot use video cable for checking.Please use SG whose output impedance is 75 ohm.

3. Set to FM tuner function and scan the input FM signal with

automatic scanning.

4. Confirm that input Frequency of A, B and C detected and

automatic scanning stops.

The stop of automatic scanning means “The station signal is

received in good condition”.

FM AUTO STOP CHECK

signal generator

set

+

– 75

TUNER SECTION 0 dB = 1 V

CD SECTION

[TEST DISC LIST]Use the following test disc on test mode.

• CD: YEDS-18 (PART No. 3-702-101-01)

or

PATD-012 (PART No. 4-225-203-01)

FOCUS BIAS CHECK

Procedure:1. Connect the oscilloscope to CN302 pin 17 (RFMON) and

CN302 pin 1 (GND) on the MOTHERBOARD board.

2. Press the [?/1] button to turn the power on, and press the [CD]

button to select CD function.

3. Set the test disc (CD: YEDS-18) on the tray and press [u]button to playback.

4. Confirm that oscilloscope waveform is as shown in the figure

below (eye pattern).

A good eye pattern means that the diamond shape (¡) in the

center of the waveform can be clearly distinguished.

VOLT/DIV: 200 mVTIME/DIV: 500 ns

level: 1.1 ± 0.25 Vp-p (DVDSL)1.0 ± 0.25 Vp-p (CD)

Checking Location:-MOTHERBOARD Board (CONDUCTOR SIDE)-

CN302

pin 1 (GND)pin 17 (RFMON)

+

–

MOTHERBOARD board

oscilloscope(DC range)

CN302 pin 17 (RFMON)

CN302 pin 1 (GND)


22/120

Switching Regulator Diagnosis Flow (HCD-SHAKE33)

The Output from Switching regulator is checked.

Is following power voltage up to standard?

Standby

CN 3 pin1

CN 2 pin10

AC IN

Yes

No

Yes

END

No

Checks whe

If there are n

Main on/Sub

Replaces Sw

The Power Control signal to Switching regulator is checked.Is following power voltage OK?

Main on/Sub on

CN 3 :pin6

13V±0.5V 13V±0.5V0V 0V

pin7 0V 0V

pin5 0V 0V

pin4 0V 0V

pin1 0V 0V

13V±0.5V61V±5%

24V±2.5V

-24V±2.5V

-61V±5%

16V~23V

(1) AC input

(2) Fuse

(3) Sub Power transformer

(4) CN 3 Connector

pin1-2: 13V

pin3-4: GND

pin5: AC-DET

pin6: MAIN-ON

(5) MAIN Power transformer

(6) CN 2 Connector

pin1: V3+ (DC+16V~23V) _ (ref-V1)

pin2-4: V1- (DC-61V)

pin5: V2- (DC-24V)

pin6: GND pin7: V2+ (DC+24V)

pin8-10: V1+ (DC+61V)

Hi (3.3V)

Power OnDemo mode

Low (0V)Low (0V)

Standby

Power OnDemo mode

(1)(2)

(3)

(6)

(5)

(4)


23/120

Switching Regulator Diagnosis Flow (HCD-SHAKE77)

(1) AC Input(2) 15A/250V AC Fuse

(3) Retifier - 25A600V

(4) PFC MOSFET

(5) PFC Inductor

(6) PFC Diode

(7) Sub Fuse

(8) Sub Switching MOSFET

(9) Sub Transformer

(10) Sub Output Diode

(11) CN4 connector

pin 1: P-cont

pin 2: ACD

pin 3 to 4: GND

pin 5 to 6: 13.5V

(12) LLC Main Fuse(13) LLC Main Switching MOSFET K18A 60V

(14) LLC Transformer

(15) Main output Diode

(16) CN2 connector

pin1: 17V

pin2 to 4: -VH (-62.5V)

pin5: -VL (-22.5V)

pin6: GND

pin7: +VL (+22.5V)

pin8 to 10: +VH (+62.5V)

(17) J60 for 13.5V GND

(18) J66 for 13.5V Output

Yes

AC IN

The Power Control signal to SMPS as below voltage?

P-cont

CN4 Pin1:

ECO Mode

Low (0V)

Demo Mode

Low (0V)

Power On

Hi (2.7V-3.3V)

Check whet

outlet are no

If there are

circumferen

The SMPS output as below voltage?

CN2 Pin10(+) + CN2 Pin2(-):

Main Output (VH) ECO Mode

Low (0V)

ECO Mode

Low (0V)

ECO Mode

Low (0V)

ECO Mode

CN2 Pin7(+) + CN2 Pin5(-):

Main Output (VL)

Main Output (V3)

Sub Output

CN2 Pin1(+) + CN2 Pin2(-):

J66(+) + J60(-): Hi (13.5V±0.65V) Hi (13.5V±0.65V)

Demo Mode

Low (0V)

Demo Mode

Low (0V)

Demo Mode

Low (0V)

Demo Mode

Hi (125V±6.25V

Power On

Power On

Hi (45V±2.25V)

Power On

Hi (14V±0.07V)

Power On

Hi (13.5V±0.65V

Yes

END

No

(10)

(11)

(18)(17)

(9)(3)

(4)(5)

(12)

(13)

(14)

(15)

(16)

(7)

(8)

(6)

(1)

(2)


24/120

Optical Block Diagnosis Flow (HCD-SHAKE33/SHAKE77) (1/2)

Does Optical pickup move to inner circumference?

(Visual check)

Yes

Yes

No Checks CL335 for +3.3V and +1.2V REG IC303.

Does it output the power voltage of 3.3V and 1.2V?

Checks CN401 SL+/SL- signal.

Does it output the signal?

Does Spindle motor rotate?

(Visual check)

Yes

Does Optical pickup do focus search?

(Visual check)

No Checks IC303 circumference circuit for +1.2V.

Checks IC002 (JL040) circumference circuit for

+3.3V.

Yes

A

No

No No

No

No

Checks circumference circuit for SL+/SL- of IC40

Checks circumference circuit of IC301 FMO Sign

REMOVE TOP PANEL

TURN ON

TRAY IN

The Sled motor has a problem.

Replaces BU.

Checks CN401 SP+/SP- signal.


The Spindle motor has a problem.

Replaces BU.

Checks circumference circuit for SP+/SP of IC40

Checks circumference circuit of IC301 DMO Sign

Checks CN302 FCS+/FCS- signal.


The Optical pickup has a problem.

Replaces BU.

Checks circumference circuit for FCS+/FCS- of I

Checks circumference circuit of IC301 FOO Sign

Yes

Yes

Yes


25/120

Optical Block Diagnosis Flow (HCD-SHAKE33/SHAKE77) (2/2)

Does laser diode become luminous?

(Visual check)

Is output level of RF signal (JL317) up to standard?

RF Level = 1.05 ±0.45 Vpp

Test CD:YEDS-18

Is there no problem with Long term Aging Test (60min)?

Confirms that there is no sound skip.

END

No

No

Checks JL306 (LD780) signal.

Does it output 2V when laser become luminous?


Replaces BU.

DISC IN

No

A

Is output level of RF signal (JL317) up to standard?

RF Level = 1.05 ±0.45 Vpp

Test CD:YEDS-18Replaces BU if it is not up to standar

No

No

YesYes

Yes

Yes

Yes

Yes

Yes

Checks circumference circuit of Q40

Checks circumference circuit of IC30

If it is not up to standard,

Lens cleaning is performed.


Replaces BU.


26/120

DAMP / MOTHERBOARD Mount Diagnosis Flow (HCD-SHAKE33/SHAKE77) (1/2)

PLAY MUSIC

Is there audio output from DAMP Board? Checks 13V output of CN001 1pin(Main ON).

Is the power voltage OK?

Checks 3V output of CN001 6pin(Main ON).


Checks +62.5V output of CN1000 10pin(+VH),

-62.5V output of CN1000 2pin(-VH) and -49V

output of CN1000 1pin (-49V).


Checks OUT terminal +50.5V output of REG IC1002

Or, checks GND and OUT Terminal with Tester.

Is it shorted out?

Reinserts the cable or Exchanges.

If there are no problems, checks output of

Switching Regulator Board.



Main ON of MOTHERBOARD Board side.



Switching Regulator Board.

Checks circumference circuit of REG IC1002

If there are no problems, exchanges IC1002.

A B

Yes

Yes

Yes

Yes

Yes

No

Yes

No

No

No

No


27/120

DAMP / MOTHERBOARD Mount Diagnosis Flow (HCD-SHAKE33/SHAKE77) (2/2)

END

Checks OUT Terminal 5V output of REG IC1000 or,

checks GND and OUT Terminal with Tester.

Is it shorted out?

Assembles into the unit again then, checks

whether there is the audio output from

DAMP Board.

Checks circumference circuit of REG IC1000.


Checks circumference circuit of REG IC1001.


Replaces DAMP Board

Replaces DAMP Board

A B

Yes

Yes

Yes

Yes

No

No

No

No

Checks OUT Terminal -5V output of REG IC1001 or,

checks GND and OUT Terminal with Tester.

Is it shorted out?

Leave DAMP Mount to a state of it only and, checks

Power Audio Driver(MOS FET) with Tester.

Is it shorted out? (Refer to Page 28.)


28/120

MOSFET Confirmation for 4CH DAMP Mount (SHAKE33)

C1312

C 1 3 1 3

C1314

C 1 3 1 6

C 1 1 2 2

C1317

C 1 3 1 8

C 1 1 2 5

C 1 1 2 6

R 1 3 0 5

R1308

C 1 1 5 7

C 1 1 6 0

C1166

R1333

C1169

C 1 1 8 0

C1182

C1183

R1352

C 1 1 9 0

C1191

C 1 1 9 2

R 1 5 5 7

CL1001

CL1002

CL1003CL1004

CL1005

CL1006

CL1007

CL1008

R1374

CL1009

CL1010CL1011

CL1012

CL1013

CL1014

CL1015

CL1016

CL1019

R1385

CL1037 CL1038

C L 1 0 4 2

CL1043

CL1044

CL1045

C L 1 0 4 6

C L 1 0 4 7

CL1048

CL1049

CL1050

C L 1 0 5 1

C L 1 0 5 2

CL1053

CL1054

CL1055

C L 1 0 5 6

C L 1 0 5 7

CL1058

CL1059

CL1060

C1209

CL1074CL1075CL1079

C1223

CL1085

R 1 2 0 8

C1234

C 1 2 3 6

C1237

C 1 2 3 9

R1212

C1240

C 1 2 4 1

C1247

C 1 2 5 7

C1258

C1259

R1234

C 1 2 6 7

C1268

C 1 2 6 9

R1275 C L 1 1 0 7

R1286

C1303

C 1 1 1 2

R1316

R 1 2 7 1

R 1 6 0 1

R 1 6 0 2

R1604R1609

R 1 3 7 2

R1199

R1250

R 1 5 9 1

C 1 3 2 9

C 1 3 3 5

C 1 3 7 4

C 1 3 6 9

C 1 3 6 2

C 1 3 6 3

R 1 6 1 7

R1646

R1296

R 1 5 9 2

C1243C1285

R 1 3 5 1

R 1 5 9 4

CL1088CL1089

CL1080

CL1083

CL1084

CL1090

CL1040

CL1039

R 1 6 1 8

C1255

R 1 3 3 0

C1260

CL1106CL1101

CL1100 CL1105CL1102

CL1099

C1310

R 1 3 6 3

C1302 CL1104

CL1103

C1224C1232

R 1 2 6 3

CL1032

C1178C1184

R 1 2 2 7

CL1027

CL1033

CL1021

CL1035

CL1022 CL1028CL1020 CL1026 CL1029

CL1036

CL1023

CL1034

CL1066CL1072 CL1063

CL1069

C1490 C1488C1504 C1502

R 1 6 3 6

R 1 6 1 4

R 1 5 9 8

R 1 5 9 7

C 1 3 2 5

C 1 1 6 3

CL1068

CL1071

CL1067

CL1041

CL1062

CL1061

CL1070

R1675 R 1 6 8 2R1681

C 1 0 2 6

C1517

R1699

R 1 7 0 0

CL1064CL1065

R 1 3 7 6

R1382

R 1 3 8 8

R1321

R 1 3 1 3

R 1 3 3 6

R 1 2 8 9

R1284

R 1 2 7 8

R 1 2 1 3

R 1 2 3 7

R1223

C 1 3 2 3

C 1 1 6 4

C 1 5 2 5

C 1 5 2 6

C 1 5 3 0

C 1 5 2 7

C 1 5 2 9

C 1 5 2 8

CL1073

C 1 5 3 1

C 1 5 3 3

C 1 5 3 4

C 1 5 3 2

CL1082

CL1109

CL1108

CL1110

R1326R1359R1228 R1232R1253R1260

R1244R1350 R1294 R1197

Tester

Tester

Tester

Tester

Tester

Tester

Tester Tester

Please check each channel’s resistance value for the Coil’s terminal and Capacitor’s + and – terminal.

These terminal is equal to resistance value for POWER AUDIO DRIVER terminal.


29/120

MOSFET Confirmation for 6CH DAMP Mount (SHAKE77)

CL1170

CL1171 CL1172

CL1175

C1121

CL1176

C 1 1 2 2

CL1177

CL1178

C 1 1 2 5

C 1 1 2 6

R1101

C1511

C1512

C1320

CL1181

CL1182

C1324

CL1185

CL1186

CL1187

C 1 1 3 3

CL1188

R 1 1 1 0

R1114

CL1191

R1116

CL1192

CL1193

C 1 1 4 0

R 1 1 1 9

C1141

CL1196

C1142

CL1197

C1337

C 1 3 3 9

C 1 1 4 5

R 1 5 0 6

C1340

R 1 1 2 5

C1341

C1342

C 1 3 4 3

R 1 1 2 8

C 1 1 5 1

C1152

C 1 1 5 3

C 1 3 4 9

C 1 1 5 5

C1156

C 1 1 5 9

C 1 3 5 1

R1136

C1352

C 1 3 5 3

C 1 3 5 4

R 1 5 2 1

R 1 1 3 9

C1161

C 1 1 6 2

C 1 3 5 8

R1526

R 1 5 2 9

R 1 1 4 2

C 1 3 6 2

C 1 3 6 3

R 1 1 4 8

R 1 5 3 3

C 1 3 6 9

R 1 5 3 7

R 1 1 5 0

R1539

R1154

C 1 3 7 0

C 1 3 7 1

C 1 3 7 2

R 1 5 4 0

C 1 3 7 4

C1375

R 1 5 4 6

R1550

R1168

R 1 5 5 3

R1557

R 1 1 7 4

C1390

C1391

R1177

R 1 1 7 9

CL1001

CL1002CL1003

CL1004

CL1005

CL1006CL1007

CL1008

CL1009

R 1 1 8 5

CL1010

R1189

CL1011CL1012

CL1013

C L 1 0 1 4

CL1015CL1016

CL1019

R 1 1 9 2

CL1210

CL1211CL1212

CL1213

CL1214

CL1215

CL1216

CL1022CL1023

CL1024

R1391

CL1219

CL1025

R1588

CL1028

R1589

CL1029

R1396

CL1220

CL1221

CL1222

CL1223

CL1224

CL1030

CL1225

CL1031

CL1226

CL1032

CL1227

CL1033

CL1228

CL1034

CL1035

CL1036

CL1037 CL1038

CL1039

CL1040

C 1 4 0 0

C1401

C 1 4 0 2

C1403

Q1018

C 1 4 0 5

C1406

C 1 4 0 7

C1414

C1030

C1420

D 1 0 1 9

R 1 4 0 6

C1046

D 1 0 2 3

C1047

Q1047

C1434

C 1 4 3 6

C1437

C1438

R1411

C1439

R1412

C 1 0 5 5

R 1 4 1 6

C1057

C 1 0 5 9

Q1056

C 1 4 4 5

R 1 4 2 2

C1063

R 1 4 2 7

C 1 0 6 7

C1450

C 1 4 5 1

C1069

D 1 0 4 7

C 1 4 5 4

C 1 4 5 8

C 1 0 7 0

C 1 4 5 9

C 1 0 7 1

C 1 0 7 2

R1434

D 1 0 5 1

C1076

R 1 4 3 7

R1051

R1052

R 1 4 4 0

C1080

R1445

R 1 4 4 8

C 1 0 8 9

R 1 0 6 2

R 1 4 5 1

R 1 0 6 9

C 1 0 9 2

R1453

C1093

C1094

C1095

R1075

R1652

R 1 0 7 8

R1463

R 1 4 6 6

D 1 0 8 2

A

K

D 1 0 8 3

D 1 0 8 4

D 1 0 8 5

D 1 0 8 6

R 1 0 8 3

D 1 0 8 7

A

K

A

K

A

K

A

K

A

K

R 1 0 8 7

R 1 4 7 4

CL1108

CL1109

R1478

R1091

R 1 0 9 3

CL1110

CL1111

CL1112

CL1113

R 1 4 8 0

CL1114

CL1115CL1116

CL1117

CL1118

CL1119

R 1 4 8 6

R1489

CL1120CL1121

CL1122

CL1123

CL1124

CL1125

R 1 4 9 2

CL1126

CL1127

CL1128

R 1 6 8 9

CL1129

R1496

CL1130CL1131

CL1132

CL1133

CL1134

CL1135CL1136

CL1137

C L 1 1 3 8

C L 1 1 3 9

CL1140

CL1141 CL1142

C L 1 1 4 3

C L 1 1 4 4

CL1145

CL1146

CL1147

C L 1 1 4 8

C L 1 1 4 9

CL1150

CL1151

CL1152

C L 1 1 5 3

C L 1 1 5 4

CL1155

C 1 1 0 1

CL1156

C1102

CL1157

C 1 1 0 3

C L 1 1 5 8

C L 1 1 5 9

CL1160

CL1161

CL1162

C L 1 1 6 3

C L 1 1 6 4

CL1165

CL1166

C 1 1 1 2

CL1167

C 1 1 1 3

C 1 1 1 4

C 1 1 1 7

R1131R1157R1541 R1542 R1428 R1057R1058R1458

R1502 R1146 R1048R1450 R1394 R1099

R 1 1 6 4

B2E 2 C 1

B1C 2 E 1

Q1018,Q1047,Q1056

Tester Tester

Tester

Tester

Tester

Tester Tester

Tester Tester Tester Tester

Tester

Please check each channel’s resistance value for the Coil’s terminal and Capacitor’s + and – terminal.

These terminal is equal to resistance value for POWER AUDIO DRIVER terminal.


30/120

HCD-SHAKE33/SHAKE77

30

SECTION 6DIAGRAMS

• Circuit Boards Location

MS-476 board

4CH DAMP board (SHAKE33)6CH DAMP board (SHAKE77)

MOTHERBOARD board

TUNER board

REGULATOR, SWITCHING (3H401W)(SHAKE33)SWITCHING REGULATOR (SSN-GBR)(SHAKE77)

FL board

BLUETOOTH module

STR board

MIC board

RC-S801/A (WW)


31/120

HCD-SHAKE33/SHAKE773131

6-1. BLOCK DIAGRAM - RS SERVO, USB Section -

'(9,&( 237,&$/&0665)6*

&' 5) $03

)2&8675$&.,1* (5525 $03&' 6


32/120

HCD-SHAKE33/SHAKE77

HCD-SHAKE33/SHAKE77

3232

6-2. BLOCK DIAGRAM - MAIN Section -

M I C - D

E T E C T

173

S S I 2

_ D O

33

S S I 0

_ B C K O

29

S S I 0

_ D O

32

S S I 1

_ D I55

S S I 3

_ L R C K O

26

S S I 3

_ B C K O

24

S S I 3

_ D I28

SYSTEMCONTROLLERIC101 (2/4)

J2201

SHAKE77

MIC IN

CN2207

MIC AMPIC2201

7513

X T A L

70 71 68 67

E X T A L

X10213.333MHz

A U D I O - X

2

91 92

A U D I O - X

1

X10312.288MHz

R T C - X

1

R T C - X

2

X10132.768kHz

MIC LEVELMIN MAX

R-CH

RL

RL

J602 (1/2)

AUDIO IN 2

AUDIOIN 1

PARTYCHAIN IN

SIGNALSELECTORIC605

X

Y3

X1

B

13

9

A

10

4

X311

14

Y01

X215

STEREO A/DCONVERTER

IC606

STEREO A/DCONVERTER

IC604

STEREO A/DCONVERTER

IC609

VINL

SCKI

CD RF AMPFOCUS/TRACKING ERROR AMP

CDSYSTEMPROCESSORDIGITALSERVOPROCESSOR

IC301(2/2)

ASDATA0 118

ABCK 113

ADIN 106

13

6

LRCK7

BCK

D O U T

8

ASYNCHRONOUSSAMPLE RATECONVERTER

IC610

BCKI

LRCKI

5

6

SDIN4

SIGNALSELECTORIC607

A Y 5

VINR

VINL

14

13

DOUT 9

BCK 8

OPAMPIC603

+

+

5

3

OUT 7

OUT 1

SIGNASELECT

IC602

X0

Y0

12

1

X3

Y3

11

4

LRCKO 24

BCKO 25

SDOUT 23

1FM DRIVER

(FM RECEIVER)IC3000

ARF1 LOUT4 13

R OUT 12

DA 11

CK 8

IIC/RDSI 6

ARF25

CN3000

3

2ANTENNA

FM/AM

ST-DATA

ST-RDS

128

114

ST-CLK127

R-CH

STEREO D/ACONVERTER

IC611

BCK

DATA

1

2

VOUTL 7

VOUTR 8

STEREO D/ACONVERTER

IC615

DATA

BCK

2

1 VOUTL 7

VOUTR 8

LINK-OUT-B 5

/LINE-MUTE-FR 9

LINK-OUT-A 17

LINK-SET 17

17

16 X1

X2

X300012MHz

BT-RXD

BT-TXD

BT-RESET

3.3V

CN102

9

8

4

5BLUETOOTH

BLUETOOTHPOWERCONTROL

Q103, Q104

8 B

T - O

N

126 C

P - D

A T A

125 C

P - C

L K

65 B

T - R

X D ( M D - C

L K )

5 B

T - R

E S E T

133 B

T - T

X D

41

A N A L O G - A

S E L

42

9

BCK 1

S S I 3

_ D O U T 327

L I N K - D

E T

59

DATA 2

LRCK 3

A N A L O G - B

S E L

2

B

112

A C L K

117

A L R C K

ANALOGSELECTOR

Q604

65

BUS BUFFERIC102 (1/2)

EPROMIC105

VOUTR 8

VOUTL 7

MIC DETECTQ2201, Q2202

ANALOGSELECTORQ605, Q607

S D A

2

S C L6

169 4

) O D V K &

6

172 4

) O D V K 6

, 2

EPROMIC106

C S

1

S O / S I O 12

166 4

) O D V K 6

, 2

170 4

) O D V K 6

, 2

W P / S I O 23

S I / S I O 0

5

168 4

) O D V K &

/ .

167 4

) O D V K 6

, 2

S C L K

6

H O L D / S I O 37


33/120


34/120


35/120

HCD-SHAKE33/SHAKE773535

6-5. BLOCK DIAGRAM - PANEL, POWER SUPPLY Section -

5 - 2

0

5 -

2 0

5 - 2

0

DC-DC CONVERTERTRANSFORMERT2201 (SHAKE33)T2200 (SHAKE77)

D2003 ~ D2006 (SHAKE33)D2002 ~ D2005 (SHAKE77)

TD FL

TUBE

POWERCONTROL

PROTECTIONQ003

POWERCONTROLPROTECTION

Q007

TH571


Q006

+9V REG.IC004

+5V REG.IC006

+5V REG.IC3001

SYSTEMCONTROLLERIC101 (5/5)

83ROTARY

ENCODER

EN2101 (SHAKE77)RV2101 (SHAKE33)

VOLUME / DJ CONTROL

D2001, D2006,

D2007, D2010,D2012,

D2115 ~ D2119

78

VACUUMFLUORESCENT

DISPLAYND2001 (SHAKE33)ND2000 (SHAKE77)

40

35

38

35

REMOTECONTROLRECEIVER

IC2101 (SHAKE33)

IC2100 (SHAKE77)

135 SIRCS

56PCONT-BTSTBY

76RES

12VBUS-OE

117PCONT-DAMP

79SPM-C-MON

165C-CONT

63AC-CUT(MD-BOOT0)

THERMISTOR-PROTECT

57PCONT-PSAVE-PROTECT

80SPM-AMBIENT-TEMP

164MTK-POWER-CTRL

FL-CLK

FL-SOUT

MASTER-VOLUME

48 RGB-SOUT

FL-LATCH

134 FL-BK

SI

36CLK

37LAT

38BK

48

137

LED SELECTORIC502

2

3 RGB-SCLK

RGB-SOUTSIN

SCK

118

112

21

4 RGB-TRANS-LED-SPK/SD_WP_0

RGB-PWM-CLKPWMCLK

TRANS

85 AD-KEY1

84 AD-KEY0S2101 ~ S2114 (SHAKE33)

S2101 ~ S2102, S2104,S2106 ~ S2116 (SHAKE77)

S2001 ~ S2011 (SHAKE33)S2000 ~ S2010 (SHAKE77)

45 POWER-KEYS2115 (SHAKE33)S2100 (SHAKE77)

+3.3V

D+3.3V

5.2V

USB+5V

LED+5.2V

+1.2V SW1

SW2

VIN1

VIN2

LED DRIVEIC2000

OUT0

IOUT15

D2100 ~ D2110

LED DRIVEIC2101

OUT0I

OUT15

D2001,D2101 ~ D2112

LED DRIVEIC2102

OUT0I

OUT15

1 6 - 1

8 /OUT11I

/OUT13

1 0 - 1

2 /OUT7I

/OUT5

CN501

4

23

CN502

4

23

L

LEDSPEAKER

R

+5V

+3.3V

+9V


Q009


Q005


Q001


Q002


Q017


Q008

5 4

+1.2V REG.IC303

+1.2V 1 8

VOLTAGEDETECTOR

IC103

4 2

+3.3V REG.IC002

3

14

1

SW2

SW1

EN2

VOLTAGE REGULATORIC001

14

3

12

AC CUTCONTROLQ013

AC CUTCONTROLQ014

PROTECTION CONTOLQ012

SW15

16

VIN1

VIN2

1

16

4TRANS21PWMCLK

21PWMCLK

21PWMCLK

22SOUT

22SOUT

4TRANS

2SIN

3SCK

3SCK

3SCK

2SIN

2SIN

4TRANS

SWITCHINGTRANSISTOR

Q2001 ~ Q2002 (SHAKE33)Q2002 ~Q2003 (SHAKE77)

POWERCONTROL

PROTECTIONQ004

SHAKE33

SHAKE77


36/120

HCD-SHAKE33/SHAKE77

HCD-SHAKE33/SHAKE77

36 36

Note on Schematic Diagram:• All capacitors are in —F unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums.• All resistors are in : and 1 / 4 W or less unless otherwise specified.• 2 : nonflammable resistor.• C : panel designation.

Note for Printed Wiring Boards and Schematic Diagrams

• A : B+ Line.• B : B– Line.• H : Adjustment for repair.• Voltage and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : TUNER• Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances.• Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances.• Circled numbers refer to waveforms.• Signal path. F : AUDIO f : TUNER (FM/AM) N : MIC J : DVD PLAY E : USB

• Abbreviation AUS : Australian model E2 : 120 V AC area in E model E51 : Chilean and Peruvian models MX : Mexican model

Note on Printed Wiring Board:X : parts extracted from the component side.

: parts extracted from the conductor side.: Pattern from the side which enables seeing.

(The other layer’s patterns are not indicated.)

Caution:Pattern face side:(Conductor Side)Parts face side:

(Component Side)

Parts on the pattern face side seen fromthe pattern face are indicated.Parts on the parts face side seen from

the parts face are indicated.Note: The components identified by mark 0 or

dotted line with mark0 are critical for safety.Replace only with part number specified.

AbbreviationAUS : Australian modelE2 : 120 V AC area in E modelE51 : Chilean and Peruvian modelsMX : Mexican model

C

B

These are omitted.

E

Q

Indication of transistor

D

G

These are omitted.

S

Q

B

These are omitted.

C E

Q

B

These are omitted.

C E

Q

• Waveforms

– MOTHERBOARD Board –

348 mVp-p 12.0 MHz

1 IC451 8 (X2)

100 mV/DIV, 25 ns/DIV

928 mVp-p 13.33 MHz

3 IC101 u; (EXTAL)


4 IC101 os (AUDIO-X2)


12.28 MHz

1.06 Vp-p

2 IC101 yj (RTC-X1)

20 mV/DIV, 10 Ps/DIV

32.768 kHz

75.2 mVp-p


37/120


38/120

HCD-SHAKE33/SHAKE77

HCD-SHAKE33/SHAKE77

3838

6-7. PRINTED WIRING BOARD - MOTHERBOARD Board (Conductor Side) - • See page 30 for Circuit Boards Location. • : Uses unleaded solder.

1

A

B

C

D

E

F

G

H

I

J

K

2 3 4 5 6 7 8 9 10 11 12

R210

R211

R406

R 2 1 2

R407

R213

R 2 1 4

R020

R 2 1 6

R217

R 6 0 0

R 6 0 2

R 6 0 3

R 6 0 4

R028

R411

R 6 0 5

R 0 2 9

R606

R607

R 2 2 0

R 2 2 2

R 2 2 3

R800

R 2 2 5

R 2 2 7

R 0 3 3

R 2 2 8

R 0 3 5

R 8 0 6

R 8 0 7

R 0 3 7

R615

R 4 2 1

R 8 0 9

R039

R 4 2 2

R 4 2 3

R424

R 4 2 5

R 4 2 6

R 4 2 7

R 4 2 8

R429

R237

R 8 1 3

R 8 1 4

R621

R 8 1 5

R622

R 8 1 6

R817

R 0 4 7

R 4 3 0

R818

R 0 4 8

R 4 3 1

R819

R626

R 4 3 2

R433

R 2 4 0

C010

C011

R242

R243 R 2 4 4

R821

R245

R 0 5 1

R822

R 2 4 6

R 0 5 2

R 2 4 8

R 0 5 4

C 4 0 4

C407

R 2 5 0

R251

C409

R 2 5 2

R 2 5 3

C 6 0 1

R 2 5 6

R 2 5 8

R 2 5 9

R 6 4 2

R 6 4 4

R 6 4 5

R 6 4 6

R 6 4 7

R 6 4 8

R 2 6 0

R 4 5 5

R649

R456

R 2 6 2

R457

CL307

R 2 6 3

R264

CL309

Documents

sony hcd-shake33 hcd-shake77 ver1.0 sm