Upload
lamkiet
View
224
Download
2
Embed Size (px)
Citation preview
Synthesis and Characterization of Hydroxyapatite Nanoparticles and β-TCP Particles
Maisara S.M. Arsad & *Pat M.Lee Materials Technology Program,
Faculty of Applied Sciences, Universiti Teknologi MARA,
40450 Shah Alam, MALAYSIA * [email protected]
Lee Kong Hung Malaysia University of Science & Technology,
Petaling Jaya, MALAYSIA
Abstract - Hydroxyapatite (HA) was prepared by co-precipitation of calcium chloride and phosphoric acid while β-TCP was prepared using ammonium hydrogen phosphate and calcium chloride. The wet powders from both preparations were centrifuged, sonicated, autoclaved and calcinated to produce nanoparticles. They were characterized by SEM, XRD and FTIR. Green and sintered disc of both samples were also prepared. The hydroxyapatite nanoparticles were of rod shape structure with dimension of 65±1.0 nm for length and 25±1.0 nm for width while β-TCP was larger with dimension of 200±10 nm for length and 100±10 nm for width. The hardness of sintered hydroxyapatite disc was found to be stronger than the sintered β-TCP.
Keyword: Hydroxyapatite; β-TCP; nanoparticles: SEM; XRD; FTIR; Vickers Microhardness Tester
I. INTRODUCTION Synthetic calcium phosphates, such as calcium
hydroxyapatite, HA; Ca10(PO4)6(OH)2, and β-tricalcium phosphate, β-TCP; Ca3(PO4)2 and biphasic mixtures of these two have found use as bone substitutes [1-3]. HA or β-TCP implants exhibit relatively good tissue compatibility, and new bone is formed directly on the implants with no fibrous encapsulation [4]. However, sintered and well-crystallized HA ceramics usually demonstrated minimal in vivo resorption, with resorption times lagging the new bone formation rates [5-9]. Kilian et al. [10] showed that nonsintered HA could even be phagocytized and dissolved by macrophages and osteoclasts, while sintered ceramics were not degraded and remained at the site of implantation for years following the surgery. The β-TCP, on the other hand, has a significantly high solubility [11, 12] and typically fades away from the defect site even before the completion of new bone formation. An ideal skeletal repair implant should readily take part in the bone remodeling processes, and also allow for the direct anchorage by the bony tissues surrounding it (osteoconduction) [13].
Nanosized size HA can provide large interfaces, giving high catalic activity and great adsorption capability in the catalysis and separation fields. Hydroxyapatite is non-inflammatory, causes no immunological and irritating response [14]. These scaffolds provide the necessary support as artificial extracellular matrices and permit cells to proliferate and differentiated functions. A new tissue will generate on the scaffold as the function of the scaffold as a template to guide the new tissue formation. For
biodegradable scaffold in bone tissue engineering, the scaffold will be a temporary template that introduced at the defective area or lost bone. It initiated bone tissue regeneration and new bone tissue will be form. The biodegradable scaffold is gradually degrade and replaced by newly formed bone tissue. An ideal scaffold should be biocompatible, cytocompatible, controllable biodegradable, porous and have good mechanical strength [15, 16]. The objectives of this work were to synthesize hydroxyapatite and β-TCP nanoparticles and to characterize these particles by various instrumental methods and their properties were compared.
II. MATERIALS AND METHODS
A Materials
Calcium chloride was purchased from Merck. Phosphoric acid was purchased from Systems. Tween 80 and ammonium hydrogen phosphate were purchased from Sigma-Aldrich. Liquid ammonia was purchased from R & M Chemicals. Ammonium hydrogen phosphate was purchased from Reidel-de Haën.
B. Synthesis of Sample HAP-A
The method conducted was according to the method reported [17] but with some modifications. A five neck flask was used. The flask was kept in a water bath at a temperature of 45˚C. Different solutions were added through different necks of the flask while one neck of the flask was inserted with a thermometer and the other was for pH electrode. Aqueous solution of 1.0 M calcium chloride was vigorously stirred at room temperature. A solution of 0.6 M phosphoric acid was added slowly in a dropwise manner to the vigorously stirred calcium chloride solution. An aqueous solution of 5% Tween 80 was added into the vigorously stirred solution mixture of calcium and phosphate. A certain volume of 25% (v/v) ammonia solution was then added dropwise into the solution to maintain the pH of the solution at pH10. After 4 h reaction at 40 ˚C, the reaction mixture was allowed to age for another 16 h at room temperature to complete the reaction. The suspension was centrifuged at 10,000 rpm using a table-top centrifuge for 5 min. Wet powder of sample HAP-A was obtained. C. Synthesis of Sample HAP-B
184
C978-1-4244-9803-1/11/$26.00 2011 IEEE
2011 2nd International Conference on Biotechnology and Food Science IPCBEE vol.7 (2011) © (2011) IACSIT Press, Singapore
Aqueous solution of calcium chloride was vigorously stirred at room temperature. A solution of ammonium hydrogen phosphate was slowly added dropwise to the calcium chloride solution. Ammonia solution was added dropwise into solution to adjust the pH 10 [18]. After reaction at 40 ˚C for 4 h and the reaction maintain was stirred for another 16 h at room temperature. The white precipitate of HAP-B was formed.
D. Autoclaved, Sonicated and Calcined
After aging of both samples, the solutions were transferred to the autoclave (HICLAVE HVE-50, HIRAYAMA), and autoclaved at 105˚C for 4 h and 130 ˚C for another 4 h. The resultant wet powder was centrifuged using 10,000 rpm for 5 min. Ethanol was added to the pellet and the suspension was sonicated using ultrasonicator for 20 min and dried in an oven at 100oC for 3 hours. The dried powder was calcinated at 900 ˚C for 4 hours before sample analysis. E. Preparation of Green and Sintered Disc
Powder samples were compressed into cylindrical tablets with a diameter of 12.80±0.02 mm and thickness of 2.00±0.03 mm under a uniaxial pressure of 5.0 MPa for 5 min to prepare green disc. The sintered disc were prepared by sintered the green disc at 1200ºC for 2 hours with same diameter and thickness. F. X-ray Diffraction (XRD)
The structure of HAP-A and HAP-B were examined using XRD Rigaku Geiger-Flex Japan. The powder was examined with Ni filtered CuKα radiation generated at 40 kV and 30 mA. The powders were scanned from 3-100˚ 2θ with a scan speed of 2˚ per minute. The peaks obtained were compared with standard references in JCPDS file available in software for hydroxyapatite (09-0432) [19] G. Fourier-transformed Infrared Spectroscopy (FTIR)
The functional groups of the hydroxyapatite were identified by FTIR Perkin Elmer using the KBr-disc method. The FTIR spectrum was scanned from 4000-400cm-1 [20]. H. Vicker’s Microhardness Tester
Hardness measurements were performed on a Vickers microhardness tester (MITUTOYO MVK-HI). Loads of 2, 5 and 10 N was applied to the surface of each compressed disc for 15 s through a pyramidal diamond indenter. Diagonal length of the indentation was measured through a micrometric eyepiece with an objective lens of 40º. The tests were repeated 5 times for each sample. The Vickers hardness number was calculated using the equation VHN = (2Fsinθ/2)/d2, where F is the applied load in grams, θ is the angle between opposite faces of indenter (136º), and d is the diagonal length of indentation in micrometers [21].
III. RESULTS AND DISCUSSION XRD pattern of the sample HAP-A showed the structure
of the prepared sample was similar to the hydroxyapatite standard as shown in Fig. 1. There is a high consistency between the data of HAP-A and that from the standard data base, with lattice dimensions of a = b = 0.9418 nm, c = 0.6884 nm. No other impurity was observed in the XRD pattern, indicating that the chief inorganic phase of the sample is hydroxyapatite crystal. The result obtain was similar to [22] as reported.
Figure 1. XRD of (a) HAP-A nanoparticles and (b) library standard of hydroxyapatite.
XRD pattern of HAP-B as shown in Fig.2 showed that it is similar in structure to the standard β-TCP which has Ca:P ratio of 3:2. The result obtained for β-TCP was similar to that reported by [23]. No α-TCP phase and HA phase were detected in the XRD pattern of the powder β-TCP with lattice dimensions of a = b = 1.0429 nm, c = 3.7380 nm.
Figure 2. XRD of (a) HAP-B nanoparticles and (b) library standard of β-TCP.
FTIR spectrum as shown in Fig. 3 showed the characteristic absorption peaks of sample HAP-A
(b)
(a)
(a)
(b)
185
nanoparticles.attributable to1 was attribuOH- ions anassigned to thbands for PO1093cm-1. Thvibration of thpeak, togethecorrespond toPO4
3 in hydrthose reported
The FTIR4. The characobserved witattributable towere the stret561 and 606 c
in β-TCP [2cm-1 indicatinsample.
4000.0 30
-1.0
0
1
2
3
4
5
6
7
8
9
10
11
12 12.6
%T
3433
4000.0 -2.0 0 2 4 6 8
10 12 14 16 18 20 22 24 25.2
%T
357
. The broad bo adsorbed wautable to the nd the mediumhe O-H defor
O43- appear at
e observation he PO4
3- bander with the sho the triply droxyapatite.. Od [17, 18, 22].
Figure 3. FTIR
R spectrum of cteristic PO4
3−
th the broad o adsorbed watching mode ocm−1 represent
Figure 4: FTIR
23, 24]. The ng the absence
000 2000
1996
3000
71 2081
2148
3432
bands at 3432 ater, while shastretching vibm sharp peakrmation modet 470, 568, 6of the asymm
ds at 964cm-1 harp peaks at degenerate beOur FTIR res
R spectrum of HA
HAP-B powd− absorption ba
bands at 34ater. The bandof PO4
3− groupt the vibration
R spectrum of HA
absence of a e of O-H func
1500 cm-1
1631 1404
2000 1500 cm-1
1642 1996 1
and 1642 cm-
arp peak at 35bration of the k at 633cm-1
e. The charact02, 964, 104
metric P-O streas a distingui633, 602, 56
ending vibratiosult was sim
AP-A
ders is shownands of β-TCP
433 and 1631ds at 900–1200p. The sharp pe
peaks of PO43
AP-B
sharp peak actional group
1000
1030 606
959 561
1000 1041 633
6
964
1093
-1 were 71 cm-
lattice was teristic 1, and
etching ishable 68cm-1 ons of
milar to
in Fig. P were 1 cm−1
0 cm−1 eaks at 3−
at 3571 in the
Aid
exBRwTst65agshfr[1le14au
di1212thpeTµ
450.0
6
470
400.0
3602
568
470
The resultA prepared wdentified as β-
Scanning examine the mo
B which have Rod shape nanwas obtained foThe image shotructures of 5±1.0 nm forgglomeration hows needle-lrom 30–60 nm17] reported tengths of the4.9×24.0 nmutoclaving tem
Figure 5. Sc
The size oiameter and t200ºC for 2 ho2.00±0.04 nmhickness. The ellet for samp
The grain size m is larger tha
Figure 6. Sca
ts of XRD anwas hydroxyaTCP. electron microrphologies o
been autoclanoparticles of for the sampleowed clearly nanoparticlesr length and was observedlike morpholo
m and the lengthat the averae resultant H
m to 17.5×5mperature from
canning electron m
of the green thickness 2.0ours, the size m for diam
shrinkage ofple HAP-A anof sintered disan that before
anning electron m
nd FTIR indicaapatite while
roscope (SEMf the samples aved, sonicatesizes in the r
e HAP-A as ilthe clear con
s with avera25±1.0 nm
d. From the oogy with partgth from 100–age diameters
HAP nanorod6.1 nm wit
m 100 to 200 °
micrograph HAP
pellet is 120±0.03 mm. of pellet was eter and 1.9f the green p
nd HAP-B is nsk as shown isintering.
micrograph of sint
ated that the Hthe HAP-B
M) was useHAP-A and H
ed and calcinrange of 50-70lustrated in F
ntour of rod sage dimensionfor width anther report [2ticle width ra
–400 nm. Aili s and the ave
ds increased th increasing°C.
-A nanoparticles
.80±0.04 mmAfter sinterinslightly reduc90±0.03 mmpellet and sinnot much diffein Fig. 6 is 1.5
tered HAP-A disc
HAP-was
ed to HAP-nated. 0 nm ig. 5. shape n of
nd no 22], it anged et al. erage from
g the
m for ng at ced to
m for ntered erent. 5±0.5
c
186
The hardn1050 MPa aftrespectively (becomes greawere 4260, 375 and 10 N. r[25] found thwhich was prhours determload of 10 N reported that tof HA structu1300ºC was 6
Figure 7. Comp
Figure 8. Sc
Scanning 8. The imagedimensions indimension ofwidth similarwere not fusedthat majority shape and cleare highly bbiomedical im
Sintered
ness of disc pater indended w(Fig. 7). The ater when sin701, 2852 MPrespectively ahat the hardnressed at 80 M
mined using vwas 297.45
the compressiures which pro6.00±0.7 GPa
parison of hardnesat differen
canning electron
electron microe shows rod sn the range of 200±10 nm r to that repord together witof the particleeaner contourbeneficial for mplants.
d Disc ( )
allet HAP-A wwith forces of
hardness of ntered at 1200A after indend
as shown in Fness for the hMPa and sintevickers hardne
± 9.53 MPa. on strength ofocessed and si
ss of for green annt laoding strengt
micrograph of HA
ograph of HAshape structurof 200-500 n
for length arted [18]. Theth other crystaes were of sinrs with no agr coating of
) Green Disc
were 1400, 137f 2 N, 5 N andhydroxyapatit0ºC for 2 h, ded with force
Fig. 7. Kananahydroxyapatit
ered at 1200ºCess tester undTimothy et al
f zero-porosityintered at 110
nd sintered HAP-Ath
AP-B nanopartic
AP-B is shownres of particlenm with an aand 100±10 ne particles pr
als. It can be inngle crystals, rgglomeration,
nanoparticles
( ( ( )
70 and d 10 N te disc which
es of 2, a et al. te disc C for 2 der the l. [26], y value 00ºC to
A discs
les
n in Fig. es with average nm for repared nferred regular which
s onto
µre
95resiMrecoan1an
F
syceHphbi
TG
The grain sm. The grain
eported [27]
Figure 9. Scanni
The hardne54 MPa afterespectively. Tintered at 120
MPa after indespectively as ompressive stnd the fractur125ºC were 2nd 0.92 ±0.04
Figure 10. Compa
Hydroxyapaynthesized byentrifugation,
Hydroxyapatitehysical propeiomedical and
This work Technology anGrant No.03-0
Sintered
size of β-TCP n size is large
ing electron micr
ss of green dir indended witThe hardness 00ºC for 2 h, dended with shown in Fig
trength, flexurre toughness o291±15 MPa,Mpa·m0.5 res
arison of hardnesdifferent lo
IV. Catite and β-Ty using diff
autoclavinge nanoparticleerties than β-Td biotechnolog
ACKNOW
was supportend Innovatio01-01-SF0092
d Disc (
as shown in er before sinte
rograph of sintere
isc HAP-B weth forces of 2of disc becowhich were forces of 10. Biqin et a
ral strength, of the sintered, 93.0±8.7 Mspectively at a
s of green and sinoading strength
CONCLUSION TCP nanoparferent chemicg, drying aes and disc deTCP and has
gical applicatio
WLEDGEMENT ed by the Mion, Malaysia 2 & 02-01-0
) Green Disc
Fig. 9 is 2.0 ±ering same as
ed TCP nanoparti
ere 1050, 11062 N, 5 N and mes greater w3751, 2942, 2, 5 and 1
al.[23] reporteelasticity modd pieces β-TC
MPa, 72.4±7.5 a load 2.0 kg.
ntered HAP-B dis
rticles have cals followedand calcinatemonstrated bs the potentiaons.
inistry of Sci(e-Science
1-SF0214) an
( )
± 0.5 s that
cles
6 and 10 N when 2200
10 N ed the dulus CP at
GPa
scs at
been d by tions. better al for
ence, Fund nd a
187187
post-graduate scholarship was awarded to Maisara S.M. Arsad. The authors would also like to thank the University for providing facilities for conducting this research and Research Management Institute, UiTM for the support.
REFERENCES [1] C. P. Nunes, S. J. Simske, R. Sachdeya, and L. M. Wolford, “Long-
term ingrowth and apposition of porous hydroxylapatite implants” J. Biomed Mater Res, 1997, vol. 36, pp. 560 –563.
[2] R. W. Nicholas and T. A. Lange, “Granular tricalcium phosphate grafting of cavitary lesions in human bone”, J. Clin Orthop, 1994, vol. 306, pp. 197–203.
[3] J. C. Elliott, “Structure and Chemistry of the Apatites and Other Calcium Orthophosphates”. Amsterdam: Elsevier, 1994.
[4] M. Spector, “Anorganic bovine bone and ceramic analogs of bone mineral as implants to facilitate bone regeneration”, J. Clin Plast Surg, 1994 vol. 21, pp. 437– 444
[5] D. S. Metsger, T. D. Driskell, J. R. Paulsrud, “Tricalcium phosphate ceramic—A resorbable bone implant: Review and current status”. J. Am Dent Assoc, 1982, vol. 105, pp. 1035–1038.
[6] J. P. Schmitz, J. O. Hollinger, and S.B. Milam, “Reconstruction of bone using calcium phosphate bone cements: A critical review”, J. Oral Maxillofac Surg, 1999, vol. 57 pp. 1122–1126.
[7] S. Joschek, B. Nies, R. Krotz, and A. Goepferich, “Chemical and physicochemical characterization of porous hydroxyapatite ceramics made of natural bone”, Biomaterials, 2000, vol. 21, pp. 1645–1658.
[8] K. A. Hing, S. M. Best, K. E. Tanner, W. Bonfield, and P. A. Revell, “Mediation of bone ingrowth in porous hydroxyapatite bone graft substitutes”, J. Biomed Mater Res A, 2004, vol. 68, pp. 187–200.
[9] S. Kamakura, Y. Sasano, T. Shimizu, K. Hatori, O. Suzuki, M. Kagayama, and K. Motegi, “Implanted octacalcium phosphate is more resorbable than β-tricalcium phosphate and hydroxyapatite”. J. Biomed Mater Res, 2002, vol. 59, pp. 29–34.
[10] O. Kilian, S. Wenisch, C. Heiss, U. Horas, E. Dingeldein, R Schnettler, “Influence of Ostim combined with autologous platelet growth factors”, Biomaterial, 2002, vol. 3, pp. 126–132.
[11] R. Tang, M. Hass, W. Wu, S. Gulde, and G. H. Nancollas, “Constant composition dissolution of mixed phases. II: Selective dissolution of calcium phosphates”, J. Colloid Interface Sci, 2003, vol. 260, pp. 379–384.
[12] S. H. Kwon, Y. K. Jun, S. H. Hong, and H. E. Kim, “Synthesis and dissolution behavior of β-TCP and HA/β-TCP composite powders”, J. Eur Ceram Soc, 2003, vol. 23, pp. 1039 –1045.
[13] A. Hoshikawa, N. Fukui, A. Fukuda, T. Sawamura, M. Hattori, K. Nakamura, and H. Oda, “Quantitative analysis of the resorption and osteoconduction process of a calcium phosphate cement and its mechanical effect for screw fixation”, Biomaterials, 2003, vol. 24, pp. 4967– 4975
[14] J. Dandurand , V. Delpech, A. Lebugle, A. Lamure, and C. Lacabanne, “Study of the mineral-organic linkage in apatitic- reinforced bone cement”, Journal of Biomedical Materials Research, 1990, vol. 24, pp. 1377
[15] S. V. Madihally and H. W. T. Matthew, “Porous chitosan scaffolds for tissue engineering”, Biomaterials, 1999, vol. 20, pp. 1133–42.
[16] J. K. F. Suh, H. W. T. Matthew, “Application of chitosan-based polysaccharide biomaterials in cartilage tissue engineering: a review”, Biomaterials, 2000, vol. 21, pp. 2589–98.
[17] W. Aili, L. Dong, Y. Hengbo, W. Huixiong, W. Yuji, R. Min, J. Tingshun, C. Xiaonong, and X. Yiqing, “Size-controlled synthesis of Hydroxyapatite nanorods by chemical precipitation in the presence of organic modifier”, J. Mat. Sc. Eng., 2007, vol. C 27, pp. 865-869,
[18] R. Murugan and S. Ramakrishna, “Bioresorbable composite bone paste using polysaccharide based nano hydroxyapatite”, Biomaterials, 2004, vol. 25, pp. 3829–3835.
[19] F. Izumi and T. Ikeda, Mater. Sci. Forum, 2000, vol. 321 pp.198 [20] A. Douglas Skoog, M. Donald West, F. James Holler, R. Stanley
Crouch, “Analytical Chemistry: An Introduction”, seventh Edition (2000)
[21] W. Li, L. Yue, L. Chunzhong, “In situ processing and properties of nanostructured hydroxyapatite/alginate composite”, J Nanopart Res, 2009, vol. 11, pp. 691–699
[22] E. Nejati, V. Firouzdor, M.B. Eslaminejad, F. Bagheri, Needle-like nano hydroxyapatite/poly(L-lactide acid) composite scaffold for bone tissue engineering application, Materials Science and Engineering C, 2009, vol. 29, pp. 942–949
[23] C. Biqin, Z. Zhaoquan, Z. Jingxian, L. Qingling, J. Dongliang, “Fabrication and mechanical properties of β-TCP pieces by gel-casting method”, Materials Science and Engineering C, 2008, vol. 28 pp. 1052–1056
[24] S. Raynaud, E. Champion, D. Bernache-Assollant, P. Thomas, Biomaterials, 2002, vol. 23 pp. 1065
[25] S. Kannana, A. Rebelo, A.F. Lemos, A. Barba, J.M.F. Ferreira, “Synthesis and mechanical behaviour of chlorapatite and chlorapatite/β-TCP composites”, Journal of the European Ceramic Society, 2007, vol. 27, pp. 2287–2294
[26] P. Timothy Hoepfner and E.D. Case, “The influence of the microstructure on the hardness of sintered hydroxyapatite”, Ceramics International, 2003, vol. 29, pp. 699–706
[27] Dj. Veljovic´, I. Zalite, E. Palcevskis, I. Smiciklas, R. Petrovic´, Dj. Janac´kovic´, “Microwave sintering of fine grained HAP and HAP/TCP bioceramics”, Ceramics International, 2010, vol. 36, pp. 595–603
188