Embed Size (px)
Citation preview
Park Distance Control (PDC)BMW 3er-Reihe, Limousine, Coupé, Cabrio, touring, compact (E36/4, -/2, -/C, -/3, -/5)
Nur zum Gebrauch in der BMW HO bestimmt.Einbauzeit ca. 3 Stunden, die je nach Zustand und Ausstattung des Fahrzeuges abweichen kann.Elektrokenntnisse sind Voraussetzung.
BMW Parts and Accessories – Installation InstructionPark Distance Control (PDC)BMW 3 Series, saloon, Coupé, Convertible, touring, compact (E36/4, -/2, -/C, -/3, -/5)
Instructions de montage des pièces et des accessoires BMWContrôle de distance au stationnement (PDC)BMW Série 3, berline, coupé, cabriolet, touring, compact (E36/4, -/2, -/C, -/3, -/5)
BMW Onderdelen en accessoires – MontagehandleidingPark Distance Control (PDC)BMW 3-serie, sedan, coupé, cabrio, touring, compact (E36/4, -/2, -/C, -/3, -/5)
BMW Delar och tillbehör – MonteringsanvisningPark Distance Control (PDC)BMW 3-serie sedan, coupé, cabriolet, touring, compact (E36/4, -/2, -/C, -/3, -/5)
Ricambi e accessori BMW – Istruzioni di montaggioPark Distance Control (PDC)BMW Serie 3, berlina, Coupé, Cabrio, touring, compact (E36/4, -/2, -/C, -/3, -/5)
BMW piezas y accesorios – instrucciones de montajeSistema de Control de Distancia Posterior (PDC)BMW Serie 3 berlina, Coupé, Cabrio, touring, compact (E36/4, -/2, -/C, -/3, -/5)
Peças e Acessórios BMW – Instruções de MontagemPark Distance Control (PDC)Modelos BMW da Série 3, Berlina, Coupé, Cabriolet, touring e compact (E36/4, -/2, -/C, -/3, -/5)
1Best.-Nr. 01 29 9 415 408 V/98 Printed in Germany
F 36 66 069
Teile und Zubehör - Einbauanleitung
17
Park Distance Control (PDC)BMW 3 Series, saloon, Coupé, Convertible, touring, compact (E36/4, -/2, -/3, -/5)
Only for use within the BMW dealer organisation.Fitting time approx. 3 hours, depending on thecondition of and equipment in the car.Electrical skills are required.
General notesThe fitting method is shown for left-hand drivemodels. For right-hand drive models the fittingwork must be carried out the opposite way roundon some occasions.
If the PIN slots specified in these instructions arealready assigned, bridges, double crimps orparallel connections must be used.
Up to model year 1994, smooth painted bumperguards were fitted in the vehicles. The use ofbumper guards for PDC (textured surface) in therear bumper means that fitting replacement frontbumper guards may also have to be considered tokeep the car's uniform appearance.
Cable installationKeep precisely to the designated cabling routes inthe vehicle to avoid faults.
Under no circumstances should you use"Scotchlock quick connectors" since they maycause faults in the vehicle electrical systems.
Ensure that when you fit the cables in the car theyare not kinked or damages since otherwise faultsmay occur whose later location may require a greatdeal of work. The costs incurred by this work willnot be reimbursed by BMW.
Tools and equipment requiredCross slot screwdriverStraight slot screwdriverSW 10 mm open-ended spannerCentrepunchAnti-corrosion paint1/2 inch reversible ratchet
1/2 inch extension1/2 inch SW 10 mm, 13 mm, 16 mm and 17 mm socketsTorx wrenchDrill3.5 mm and 9 mm twist drill bits40 mm stage drill bitSpecial tool to remove jacksSpecial crimping toolWater-soluble penHammerRound fileTape measureZinc-rich primer
Table of contents
Section1. Preparatory work on the car2. Power supply wiring harness/Overview3. Ultrasonic transducer wiring harness/Overview4. To fit the power supply and ultrasonic
transducer wiring harnesses4.1 Model E36/2, -/44.2 Model E36/34.3 Model E36/54.4 Model E36/C
5. To fit the bracket, ultrasonic transducer andbumper guards
6. Circuit diagram
1. Preparatory work on the car
- Print out the error memory- Disconnect the battery- Remove the rear bumper
2. Power supply wiring harness/Overview
F 36 66 070
AA1
B
C
C1
D
E
F
1-pole pin casing1-pole socket casing
Jack
1-pole pin casing
1-pole socket casing
Jack
2-pole plug
26-pole plug
Connect to connector A1To jack from tail light unit and connect toconnector AIn the plug for left or right (E36/5) tail lightunitConnect to connector C1
To jack from tail light unit and connect toconnector CAIn the plug for left or right (E36/5) tail lightunitTo PDC gong
To PDC control unit
Blue/Yellow
Blue/Yellow
Brown
Brown
X 318/E36/5X 319/E36
X 318/E36/5X 319/E36X 363
X 300
Item Description Cable colour Connection point in car Code designation/Pug-in-place
4. To fit the power supply andultrasonic transducer wiringharnesses
4.1 Model E36/2, -/4
F 36 66 072
Fit the power supply wiring harness (1) from the taillight unit (2) to the control unit (3) and to the rearwindow shelf (4). Fit the ultrasonic transducerwiring harness (5) from the control unit (3) to theultrasonic transducers (6).
F 36 66 073
Remove the luggage compartment mat (1), sidetrim (2) and the tail light covers (3) on both sides.
F 36 66 074
Remove the nuts (1) and expanding rivets (2). Take the floor cover (3) out of the car.
F 36 66 075
Remove the expanding rivets (1). Fold back therear trim (2) in the direction indicated by the arrow.Pull the wiring harness (3) out of the clips. Removethe rear trim (2).
F 36 66 076
Disconnect the jacks (1, 2) from the socket (3) inthe left-hand tail light unit.
E36/2 Jack (1) Pin 5Jack (2) Pin 1
E36/4 Jack (1) Pin 6Jack (2) Pin 4
Connect jack (1) into socket casing (A1) and jack (2) into socket casing (C1).Connect connector (A) to connector (A1) andconnector (C) to connector (C1).Connect up connectors (B and D) in socket (3) asfollows:
E36/2 Connector (B) Pin 5Connector (D) Pin 1
E36/4 Connector (B) Pin 6Connector (D) Pin 4
Fit the plug (F) to the left-hand wheel arch and plug (E) to the rear window shelf.
F 36 66 077
Centrepunch the dimensions and drill the holeswith a 5.5 mm twist bit. Expand the hole to adiameter of 32 mm.
A = 135 mm, B = 30 mm
F 36 66 078
Drill the holes (1) with a diameter of 5.5 mm andthread the cable straps (2) through them. Securethe wiring harness (3) in the cable straps (2).Thread the plug (G) through the hole and move it tothe installation site for the control unit. Insert thegrommet (4).
F 36 66 079
Fit the plug (E) for the power supply wiring harness (1) from the luggage compartment throughthe grommet (2) to the rear window shelf.
F 36 66 080
Connect the plug (E) to the PDC gong (1).
F 36 66 081
Insert the thread and journal of the PDC gong intothe holes and secure it under the rear window shelfusing a hexagonal nut (1).
Vehicles with a low recess in the rear windowshelf
F 36 66 082
Secure the bracket (1) on the PDC gong (2) usingthe nut (3) and bolt the assembly to the vehiclebeneath the rear window shelf using the nut (4).
All models E36/2, -/4
F 36 66 083
Secure the bracket (1) using hexagonal screws (2).Insert the plugs (F, G) into the counter plugs of thesame colour on the control unit and secure themwith the fuse bars (3).
18
3. Ultrasonic transducer wiring harness/Overview
F 36 66 071
G
H
I
J
K
26-pole plug
Socket
Socket
Socket
Socket
To control unit in left or right (E36/5)rear side section To ultrasonic transducer, left
To ultrasonic transducer, centre left
To ultrasonic transducer, centre right
To ultrasonic transducer, right
Item DescriptionCable colour/Cross-section
Connection point in car Code designation/Pug-in-place
X 18013
X 18020
X 18021
X 18022
X 18023
4.2 Model E36/3
F 36 66 084
Fit the power supply wiring harness (1) from the taillight unit (2) to the control unit (3) and to the left-hand ventilation grille (4). Fit the ultrasonictransducer wiring harness (5) from the control unit (3) to the ultrasonic transducers (6).
F 36 66 085
Open the cover (1), remove the tail light covers (2)on both sides. Undo the cross slot screws (3) andremove the D column trim (4). Remove the reartrim (5).
F 36 66 086
Remove the cross slot screw (1) and the C pillartrim (2). Take out the cover (3).
F 36 66 087
Remove the cross slot screws (1) and ventilationgrille (2). Undo the cross slot screws (3) andremove the bracket (4).
F 36 66 088
Lever out the cover (1), undo the cross slot screws (2) and remove the belt mounting (3). Undo the expanding rivet (4) and remove the cover (5).
F 36 66 089
Undo the hexagonal nut (1) and the cross slotscrews (2) and remove the trim (3).
F 36 66 090
Disconnect jacks 1 (pin 6) and 2 (pin 4) from thesocket (3) on the left-hand tail light unit. Connectjack (1) to socket casing (A1) and jack (2) to socketcasing (C1). Connect connector (A) to connector(A1) and connector (C) to connector (C1). Connectconnectors (B and D) to the socket (3) as follows:
Connector (B) Pin 6Connector (D) Pin 4
F 36 66 077
Centrepunch the dimensions and drill the holeswith a 5.5 mm twist bit. Expand the hole to adiameter of 32 mm.
A = 135 mm, B = 30 mm
F 36 66 078
Drill the holes (1) with a diameter of 5.5 mm andthread the cable straps (2) through them. Securethe wiring harness (3) in the cable straps (2).Thread the plug (G) through the hole and insert the grommet (4).
F 36 66 091
Move the plug (G) for the ultrasonic wiring harness (1) to the installation site for the control unit.
F 36 66 092
Place the speed nuts (2) on the trim (1) and securethe control unit (3) using cross slot screws (4). Fit the trim (1).
F 36 66 093
Insert the plugs (F, G) into the counter plugs of thesame colour on the control unit (1) and securethem with the fuse bars (2).
F 36 66 094
Pull the insulation mat (1) out of the grille (2) andmark the dimensions. Drill holes using a 6.5 mmtwist drill bit.
A = 36 mm, B = 10 mm
F 36 66 095
Cut the nipple (2) off the PDC gong (1). Secure thePDC gong (1) using the hexagonal nut (3).
F 36 66 096
Cut out the insulation mat (1) and connect the plug (E) to the PDC gong (2).
4.3 Model E36/5
F 36 66 097
Fit the power supply wiring harness (1) from the taillight unit (2) to the control unit (3). Fit the ultrasonictransducer wiring harness (4) from the control unit (3)to the ultrasonic transducers (5).
F 36 66 098
Remove the tail light units on both sides. Take outthe luggage compartment mat (1). Remove theplastic nut (2) and lever out the left-hand luggagecompartment tray (3).
F 36 66 099
Remove the plastic nuts (1) and lever out the right-hand luggage compartment tray (2).
F 36 66 100
Remove the rivets (1) and take out the rear trim (2).
19
F 36 66 101
Disconnect jacks 1 (pin 6) and 2 (pin 8) from thesocket (3) on the right-hand tail light unit. Connectjack (1) to socket casing (A1) and jack (2) to socketcasing (C1). Connect connector (A) to connector (A1)and connector (C) to connector (C1). Connectconnectors (B and D) to the socket (3) as follows:
Connector (B) Pin 6Connector (D) Pin 8
Fit the plugs (E and F) to the bracket for the controlunit.
F 36 66 102
Centrepunch the dimensions and drill the holeswith a 5.5 mm twist bit. Expand the hole to adiameter of 32 mm.
A = 110 mm, B = 55 mm
F 36 66 103
Drill the holes (1) with a diameter of 5.5 mm andthread the cable straps (2) through them. Securethe wiring harness (3) in the cable straps. Insert thegrommet (4). Fit the plug (G) to the installation sitefor the control unit.
A = 400 mm, B = 700 mm, C = 970 mm
F 36 66 104
Secure the control unit (1) with plastic nuts (3) andthe signal generator (2) with the hexagonal nut (4)to the bracket (5).
The plug connections point upwards.
F 36 66 105
Fit the nut bracket to the car.
F 36 66 106
Insert the plugs (F, G) into the counter plugs of thesame colour on the control unit (1) and securethem with the fuse bars (2). Insert the plug (E) tothe signal generator (3). Secure the bracket (4) withhexagonal screws (5).
4.4 Model E36/C
F 36 66 107
Fit the power supply wiring harness (1) from the taillight unit (2) to the control unit (3) and to the right-hand trim (6). Fit the ultrasonic transducer wiringharness (4) from the control unit (3) to theultrasonic transducers (5).
F 36 66 108
Open the hood box cover (1) slightly (30 mm to 50 mm). Then push the hood box coverdownwards in the direction indicated by the arrow so that the luggage compartment lid (3) can beopened.
F 36 66 109
Remove the luggage compartment mat. Take outthe tail light units on both sides. Undo theexpanding rivet (1) and remove the left-handluggage compartment trim (2). Unscrew the plasticnuts (3) and take out the cover (4).
F 36 66 110
Unscrew the expanding rivet (2) and plastic nut (1)and then remove the cover (3).
F 36 66 075
Remove the expanding rivets (1). Fold back therear trim (2) in the direction indicated by the arrow.Pull the wiring harness (3) out of the clips and thenremove the rear trim (2).
Vehicles with electric hood only
F 36 66 111
Do not move the mechanism for the hood flapand electric motor.
Push the bar (1) in the direction indicated by thearrow until the motor (2) is released. Undo thespring clips (3) and disconnect both Bowdencables. Remove the securing clips (5). Undo thespring clips (6) and taken out the strut (7).
F 36 66 112
Disconnect the plug (1). Unscrew the hexagonalnuts (2) and remove the bracket (3).
All E36/C models
F 36 66 113
Disconnect jacks 1 (pin 5) and 2 (pin 1) from thesocket (3) on the left-hand tail light unit. Connectjack (1) to socket casing (A1) and jack (2) to socketcasing (C1).Connect connector (A) to connector (A1) andconnector (C) to connector (C1).Connect connectors (B and D) to the socket (3) as follows:
Connector (B) Pin 5Connector (D) Pin 1
Fit the plug (F) to the left-hand wheel arch and plug (E) through the cable passage in the left-handbackrest to the right-hand side.
20
F 36 66 114
Secure the control unit (1) to the bracket (3) usingplastic nuts (2). Only turn the cross slot screws (4)on the bracket (3) in a few turns.
F 36 66 077
Centrepunch the dimensions and drill the holeswith a 5.5 mm twist bit. Expand the hole to adiameter of 32 mm.
A = 135 mm, B = 30 mm
F 36 66 078
Drill the holes (1) with a diameter of 5.5 mm andthread the cable straps (2) through them. Securethe wiring harness (3) in the cable straps (2).Thread the plug (G) through the hole and insert thegrommet (4). Fit the plug (G) at the control unit'sinstallation site.
F 36 66 115
Insert the plugs (F, G) into the counter plugs of thesame colour on the control unit (1).
F 36 66 116
Push the control unit into the gap between thewing and the luggage compartment plate. Push thecross slot screws on the bracket (1) through theoval holes and secure them,
F 36 66 117
Fit the plug (E) for the power supply wiring harness (1) from the luggage compartment to the seat box and connect it to the standard cableties (2). Fit the plug (E) to the right-hand side of the car.
F 36 66 118
Connect the plug (E) into the PDC gong (1) andsecure the PDC gong (1) to the bracket (3) usingthe hexagonal nut (2). Ensure that the journal (4)locks into the hole provided for it.
F 36 66 119
Secure the bracket (1) to the existing welded studsusing the plastic nuts (2).
5. To fit the bracket, ultrasonictransducer and bumper guards
F 36 66 120
Carefully lever out the bumper guards (1) inthe direction indicated by the arrow using ascrewdriver, and remove them.
F 36 66 121
Hammer the expanding pins (1) inwards and leverthe expanding rivets (2) out of the bumper.
F 36 66 122
Hammer the expanding pins (1) downwards andlever the expanding rivets (2) out of the bumper.
F 36 66 123
Carefully lift out the bumper support (1) and thebumper insert (2).
E36/5 models only
F 36 66 124
Undo the hexagonal nut (1), then pull out the Torxbolt (2). Lift out the impact absorber (3).
Vehicles without standard holes only
F 36 66 125
Insert the support for PDC (1) into the bumpercasing (2). Secure it in position with severalexpanding rivets and then mark the holes for thesensors. Remove the support and drill the holes.
F 36 66 126
Secure the bracket (1) with hexagonal nuts (3) andTorx bolts (4) to the support for PDC (2). Theninsert the bracket in the rear trim and secure it withexpanding rivets.
F 36 66 127
Fit the bumper guards (1). Align and secure thebumper guard (2).
The angled section on the centre bumperguard must point upwards.
F 36 66 128
Fit the ultrasonic transducers in the bumper guardsfrom the rear.
The ultrasonic transducers must lock into themountings.
F 36 66 129
Connect the plugs to the ultrasonic transducersand secure the bumper to the car.
For all cars
The fusible insert for the reversing lights alsoacts as the fuse for the Park Distance Control.After fitting, a note is to be made on the sticker inthe fuse box.
21
6. Circuit diagram
Legend
X18013 PLUG FOR SENSOR WIRING HARNESSA81 PDC CONTROL UNITH40 PDC GONGX300 PDC CONTROL UNIT PLUGX319 TAIL LIGHTX363 PDC GONGX001 REVERSING LIGHT CONNECTORX18020 TRANSDUCER PLUG REAR LEFTX18021 TRANSDUCER PLUG REAR
CENTRE LEFTX18022 TRANSDUCER PLUG REAR
CENTRE RIGHTX18023 TRANSDUCER PLUG REAR RIGHTB34 SENSOR REAR LEFTB35 SENSOR REAR CENTRE LEFTB36 SENSOR REAR CENTRE RIGHTB37 SENSOR REAR RIGHT
22
BA
A1
C1
C D F
E
F 36 66 070
1
G H J
I KF 36 66 071
2
2
F 36 66 072
1 3
5
4 6
6
6
6
2
32
1
3
F 36 66 073
4
F 36 66 074
31
25
F 36 66 075
1
2
36
B
F E
1 A1 A
2 C13
C
F 36 66 076
D
7
A
F 36 66 077
B
8
23
1
1
4
1
F 36 66 078
500
G
210 350
9
E12
F 36 66 079
10
3
E
1F 36 66 080
11
1F 36 66 081
12
3
1
2
4 F 36 66 082
13
2
1
F
2
3
F 36 66 083
G3
14
1 3
46
6
6
6
2
F 36 66 084
5
15
F 36 66 085
4
3
2
5 1
16
2
3
1
F 36 66 086
17
4
1
3
3
2
1
F 36 66 087
18
4
F 36 66 088
5
41
3
2 2
19
F 36 66 089
2
3
1
2
20
F 36 66 090
E
F
1 A1 AB
D
3
C2 C1
21
A
F 36 66 077
B
22
23
1
1
4
1
F 36 66 078
500
G
210 350
23
F 36 66 091
1
G
24
F 36 66 092
1
4
224
3
25
F 36 66 093
G 2F 2
1
26
5
B
F 36 66 094
21
A
27
F 36 66 095
1 3
2
28
1
F 36 66 096
2
E29
F 36 66 097
45
5
5
5
213
30
2 3
F 36 66 098
1
31
2
1
F 36 66 099
32
2
1 1 1
F 36 66 100
33 E
F AA1
2
B
3
CC1
1
D
F 36 66 101
34
6
A
BF 36 66 102
35
F 36 66 103
G
4
12
12
1
2
3
C
AB
36
3
PDC 12V
F 36 66 104
13
4 5
237
F 36 66 105
1
38
F 36 66 106
45G
E
2
1F
3
5
2
39
F 36 66 107
5
41
23
56
40
F 36 66 108
2
1
41
F 36 66 109
4
213 1
3
42
7
F 36 66 110
12
3
43
F 36 66 075
1
2
344
F 36 66 111
5
1
76
33 4
4
62
45
F 36 66 112
22
23
1
46
F
B
E1 A1 A
D 23
C1 C
F 36 66 113
47
F 36 66 114
1
43
2 2
4
48
A
F 36 66 077
B
49
23
1
1
4
1
F 36 66 078
500
G
210 350
50
8
1
F
G
F 36 66 115
51
F 36 66 116
1
2
2
52
F 36 66 117
1
2E
2
53
24
3
1
E
F 36 66 118
54
1
2
F 36 66 119
55
1
11
F 36 66 120
56
F 36 66 121
1
2
57
F 36 66 122
2158
9
F 36 66 123
1
2
59
F 36 66 124
3
2
1
60
2
1F 36 66 125
61
F 36 66 126
1 3
2462
F 36 66 127
1
1
2
63
F 36 66 128
64
F 36 66 129
65 66
STOSSFAENGER
X1801325
HR-
12
HR+
0.5SCHIRM
0.5TR
1382470.9
LTG. 1-ADR. GESCHIRMT
X180232
21
HMR-
HR-
1
8
HMR+
0.5
HR+
SCHIRM0.5TR
1382470.9
WA
ND
LER
HR
X18022
LTG. 1-ADR. GESCHIRMT
B37
2
HMR-
1
HMR+
23
HML-
0.5SCHIRM
10
HML+
WA
ND
LER
HM
R
0.5TR
B36
1382470.9
X180212
LTG. 1-ADR. GESCHIRMT
KAR
X300
HML-
14
1
31
BR1.5
HML+
X319BKAR
31
1
26
HL-
BR
WA
ND
LER
HM
L
0.5
0.5
SCHIRM
13
HL+
B35
FERTIGE LTG NR. 8 357822
0.5TR
X18020
1382470.9
X319S
2
KAR
LTG. 1-ADR. GESCHIRMT
HL-
1
31
1
S
HL+
WA
ND
LER
HL
B34
BLGE0.75
X319BKAR
6
RS
RS
1
BLGE0.5
RS
KAR
VB RS
KAR
X300
X001
21
LS-
0.5BLGR
BLGE
26
25
0.5
RS
BLGE
LS+
X363
0.5
0.5BLRT
1
X319S
ST
G P
DC
KAR
LS-
1
2
RS
S
A81
LS+
LAU
TS
PR
EC
HE
R P
DC
H40
