TESNILNI MATERIALI - Dimerdimer.si/userfiles/makseal/file/katalogi/DIMER E_Katalog Tesnilni... · Sulphuric Acid 96% Sulphurous Acid Tannic Acid Tar Tartaric Acid Tetrachlorethane

TESNILNI MATERIALI

Vse informacije v pričujočem katalogu so podane v dobri veri, vendar ne dajemo nikakršnega neposrednega ali posrednega pomena, saj nimamo vpliva na posamično vrsto uporabe.

www.dimer-group.com

2TESNILNI MATERIALI

KALANDRIRANI TESNILNI MATERIALI

Barva Rdeča Modra

Žična ojačitev ne da

Opis DIMERSIL je ekonomičen tesnilni material izdelan iz mešanice organskih vlaken ter NBR/SBR kavčuka.

DIMERSIL 20 je visoko kvaliteten tesnilni material izdelan iz mešanice visoko temperaturno odpornih vlaken in NBR kavčuka.

Uporaba

TEHNIČNI PARAMETRI (standardne vrednosti za debelino 2,0 mm)

DIMERSIL 10 ima široko področje uporabe pri manj zahtevnih pogojih v različnih vrstah industrije.

DIMERSIL 20 je material namenjem za široko uporabo v različnih vrstah undustrije, kot npr. petrokemija, kemična industrija, prehrambena industrija ter strojna industrija.

Certifikati KTW Germanischer Lioyd, DVGW, BAM, TZW/W270

Razvrstitev po standardu(DIN 28 091-2) FA-Z-12-0 FA-MA-1-0 (ST)

Razvrstitev po standardu(ASTM F 104)

F712 120 M4 F712 111 M5 (M7)

Max. delovna temperatura*kratkotrajna °C 210 400

stalna °C 140 250 (para 200)

Max. delovni pritisk* Bar 40 100

Spec. gostota (DIN 28090-2) g/cm³ 1,7-2,1 1,7-2,0

Stisljivost (ASTM F 36) % 12 10

Povratna stisljivost (ASTM F 36) % 50 50

Zaostanek napetosti (175°C) (DIN 52 913) ≈ MPa 20 30

Tesnost λ (DIN 3535-6/99) ≈ mg/(m*s) 0,1 0,06

Obstojnost na tekočine -sprememba debeline po namakanjuASTM Oil IRM 903(5h/150°C) ASTM F 146 % 15 3

ASTM Fuel B(5h/23°C) ASTM F 146 % 15 5

1 - varno področje uporabe (velja tudi za paro)2 - področje uporabe je primerno, priporoča se svetovanje tehnične službe3 - obvezno je posvetovanje s tehnično službo

*Maksimalna temperatura in pritisk ne smeta biti uporabljena istočasno

2www.dimer-group.com

15www.dimer-group.comGASKET MATERIALS GASKET MATERIALS

DIMERSIL 10 DIMERSIL 20

Red BlueColour

Wire insertion No Yes

Description The economic version of material composedfrom blend of organic �bres with NBR/SBRrubber binder.

DIMERSIL 20 is high quality material basedon a blend of special high temperatureresisting �bres and other agents with NBRrubber.

Range usage

Certi�cation

Max. temperature* peak °C

Max. temperature* continous °C

Max. pressure* Bar

Density DIN 28090-2 g/cm³

DIMERSIL 10 has wide area usage in all sortsof industries at lower parameters.

DIMERSIL 20 is general purpose material andcan be used in wide range of industries suchas petrochemical, chemical, food and oil aswell as engineering area.

Germanischer LIoyd, KTW , GOST, PZH Germanischer Lioyd, DVGW, BAM,TZW/W270, GOST, PZH

FA-Z-12-0 FA-MA-1-0 (ST)

F712 120 M4 F712 111 M5 (M7)

210 400

Marking according DIN 28 091-2

Marking according ASTM F 104

140 250 (steam 200)

40 100

Compressibility ASTM F 36 %

Recovery ASTM F 36 %

Residual stress (175°C) DIN 52 913 ≈ MPa

Gas leakage λ DIN 3535-6/99 ≈ mg/(m*s)

Fluid resistance - thickness increase

Oil IRM 903 (5h/150°C) ASTM F 146

ASTM Fuel B (5h/23°C) ASTM F 146

1,7-2,1 1,7-2,0

12 10

50 50

20 30

0,1 0,06

15 3

15 5

Temperature (°C)

1 - suitable area (even for steam application)2 - suitable extended area, technical advice is recommended3 - for this area technical consultation is mandatory

Pres

sure

(bar

)

Temperature (°C)

Pres

sure

(bar

)

* Maximum temperature and pressure values can not be used simultaneously.

-40 00

20

40

50 100 150 200 210

1

3

2

-30 00

20

100

80

60

40

50 100 150 200 250 300 350 400

1

3

2

Sulphuric Acid 96%Sulphurous AcidTannic AcidTarTartaric AcidTetrachlorethaneTetrachlorethyleneThermal OilTouleneTransformer OilTransmission OilTrichlorethyleneTurpentineVegetable OilVinil BromideVinyl AcetateVinyl ChlorideWaterWhite SpiritXyleneZinc ChlorideZinc Sulphate

AAAAAAAAAAAAAAAAAAAAAA



DIMERFLON 10 DIMERFLON 11 DIMERFLON 13




Red BlueColour

Wire insertion No Yes

Description The economic version of material composedfrom blend of organic �bres with NBR/SBRrubber binder.

DIMERSIL 20 is high quality material basedon a blend of special high temperatureresisting �bres and other agents with NBRrubber.

Range usage

Certi�cation

Max. temperature* peak °C

Max. temperature* continous °C

Max. pressure* Bar

Density DIN 28090-2 g/cm³

DIMERSIL 10 has wide area usage in all sortsof industries at lower parameters.

DIMERSIL 20 is general purpose material andcan be used in wide range of industries suchas petrochemical, chemical, food and oil aswell as engineering area.

Germanischer LIoyd, KTW , GOST, PZH Germanischer Lioyd, DVGW, BAM,TZW/W270, GOST, PZH

FA-Z-12-0 FA-MA-1-0 (ST)

F712 120 M4 F712 111 M5 (M7)

210 400

Marking according DIN 28 091-2

Marking according ASTM F 104

140 250 (steam 200)

40 100

Compressibility ASTM F 36 %

Recovery ASTM F 36 %

Residual stress (175°C) DIN 52 913 ≈ MPa

Gas leakage λ DIN 3535-6/99 ≈ mg/(m*s)

Fluid resistance - thickness increase

Oil IRM 903 (5h/150°C) ASTM F 146

ASTM Fuel B (5h/23°C) ASTM F 146

1,7-2,1 1,7-2,0

12 10

50 50

20 30

0,1 0,06

15 3

15 5

Temperature (°C)

1 - suitable area (even for steam application)2 - suitable extended area, technical advice is recommended3 - for this area technical consultation is mandatory

Pres

sure

(bar

)

Temperature (°C)

Pres

sure

(bar

)

* Maximum temperature and pressure values can not be used simultaneously.

-40 00

20

40

50 100 150 200 210

1

3

2

-30 00

20

100

80

60

40

50 100 150 200 250 300 350 400

1

3

2

Sulphuric Acid 96%Sulphurous AcidTannic AcidTarTartaric AcidTetrachlorethaneTetrachlorethyleneThermal OilTouleneTransformer OilTransmission OilTrichlorethyleneTurpentineVegetable OilVinil BromideVinyl AcetateVinyl ChlorideWaterWhite SpiritXyleneZinc ChlorideZinc Sulphate




DIMERFLON 10 DIMERFLON 11 DIMERFLON 13DIMERSIL 10 DIMERSIL 20

temperatura (°C)

priti

sk (b

ar)

temperatura (°C)

priti

sk (b

ar)


www.dimer-group.com

3TESNILNI MATERIALI

350

Svetlo modra Črna

da da

DIMERSIL 30 je tesnilni material vrhunske kvalitete izdelan iz mešanice ognjeodpornih aramidnih vlaken in visoko kvalitetnega NBR kavčuka. Material je primeren za uporabo pri visokih temperaturah, ter za tesnjenje pare in plinov.

DIMERSIL 40 je vrhunski material izdelan iz karbonskih vlaken in visoko kvalitetnega NBR kavčuka.

Zaradi vsebnosti najkvalitetnejših vlaken je DIMERSIL 30 posebej primeren za uporabo v petrokemični, kemični in prehrambeni industriji ter strojni industriji. Tesnilni material je predvsem primeren za tesnjenje olj, goriv, maziv, alkohola, plinov, vode, hladilnih tekočin ter večino kislin in lugov.

DIMERSIL 40 je posebej primeren za tesnjenje pare in bazičnih medijev. Zaradi odlične tem-peraturne in kemične obstojnosti je mate-rial primerjen za za tesnjenje olj, goriv, alkalnih medijev in hladilnih tekočin.

Germanischer Lioyd, DVGW, BAM

FA-MA-1-0 (ST) FA-CA-1-0 (ST)

F712 111 M6 (M7) F712 110 M6 (M7)

450 450

350 (para 250) 300 (para 280)

120 100

1,7-2,0 1,6-1,9

10 9

55 50

32 32

0,04 0,05

3 3

5 5



OxygenPalmitic AcidPara�nPentanePerchlorethylenePerchloric AcidPetrolPetroleumPetroleum Gas LiquidPhenolPhosgenePhosphoric Acid <45%Phosphoric Acid >45%Phtalic AcidPotable WaterPotassium AcetatePotassium CarbonatePotassium ChloratePotassium ChloridePotassium CyanidePotassium Dichromate <20%Potassium Hydroxide < 50% Potassium HypochloritePotassium NitratePropanePyridineRape Seed OilRefrigerantSalicylic AcidSea WaterSilicone OilSilver NitrateSoapSodium AluminateSodium BicarbonateSodium BisulphiteSodium CarbonateSodium ChlorideSodium CyanideSodium Hydroxide < 50%Sodium SilicateSodium SulphateSodium SulphideSpirits MethylatedStarchSteamSteam High PressureSteam Low PressureStearic AcidStyreneSugarSulphurSulphur Dioxide DrySulphur TrioxideSulphuric Acid (Fuming)

CAAAAAAAAAAABAAAAAAAACAAAAAAAAAAAAAAAAABAAAAAABAAAAAAAA

AAAAAAAAAAAABAAAAAAAACAAAAAAAAAAAAAAAAACAAAAAABAAAAAAAA

AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAABAAAAAAAC

DIMERFLON 10 DIMERFLON 11 DIMERFLON 13 DIMERSIL 30 DIMERSIL 40

Light blue Black

Yes Yes

DIMERSIL 30 is superior performance sealingmaterial containing a blend of special heatresistant aramid �ber and high quality nitrilerubber binder . Material is suitable forelevated temperatures and steam applications,exhibiting excelent gas sealability.

DIMERSIL 40 is premium quality carbon bibre material with a high quality nitrile rubber binder.

Due to its composition of high quality rawmaterials, this particular grade is used inpetrochemical, chemical, food industries andwide area of machinery. It is suitable for oils,fuels , lubr icants , a lcohol , gases,hydrocarbons , water, cooling liquids and most diluted acids and alkalies.

DIMERSIL 40 is especially suitable for useunder alkaline conditions with good steamresistance. Material has excellent creepresistance and is suitable for applicationswith oils , fuels , alkaline medium andrefrigerants.

Germanischer Lioyd, DVGW, BAM, GOST GOST


F712 111 M6 (M7) F712 110 M6 (M7)

450 450

330 (steam 250) 250 (steam 250)

120 100

1,7-2,0 1,6-1,9

10 9

55 50

32 32

0,04 0,05

3 3

5 5

Temperature (°C)Temperature (°C)

Pres

sure

(bar

)

Pres

sure

(bar

)

-30 00

20

120

100

80

60

40

50 100 150 200 250 300 350 450400

1

3

2

-30 00

20

100

80

60

40

50 100 150 200 250 300 350 450400

1

3

2



OxygenPalmitic AcidPara�nPentanePerchlorethylenePerchloric AcidPetrolPetroleumPetroleum Gas LiquidPhenolPhosgenePhosphoric Acid <45%Phosphoric Acid >45%Phtalic AcidPotable WaterPotassium AcetatePotassium CarbonatePotassium ChloratePotassium ChloridePotassium CyanidePotassium Dichromate <20%Potassium Hydroxide < 50% Potassium HypochloritePotassium NitratePropanePyridineRape Seed OilRefrigerantSalicylic AcidSea WaterSilicone OilSilver NitrateSoapSodium AluminateSodium BicarbonateSodium BisulphiteSodium CarbonateSodium ChlorideSodium CyanideSodium Hydroxide < 50%Sodium SilicateSodium SulphateSodium SulphideSpirits MethylatedStarchSteamSteam High PressureSteam Low PressureStearic AcidStyreneSugarSulphurSulphur Dioxide DrySulphur TrioxideSulphuric Acid (Fuming)

CAAAAAAAAAAABAAAAAAAACAAAAAAAAAAAAAAAAABAAAAAABAAAAAAAA

AAAAAAAAAAAABAAAAAAAACAAAAAAAAAAAAAAAAACAAAAAABAAAAAAAA

AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAABAAAAAAAC

DIMERFLON 10 DIMERFLON 11 DIMERFLON 13 DIMERSIL 30 DIMERSIL 40

Light blue Black

Yes Yes

DIMERSIL 30 is superior performance sealingmaterial containing a blend of special heatresistant aramid �ber and high quality nitrilerubber binder . Material is suitable forelevated temperatures and steam applications,exhibiting excelent gas sealability.

DIMERSIL 40 is premium quality carbon bibre material with a high quality nitrile rubber binder.

Due to its composition of high quality rawmaterials, this particular grade is used inpetrochemical, chemical, food industries andwide area of machinery. It is suitable for oils,fuels , lubr icants , a lcohol , gases,hydrocarbons , water, cooling liquids and most diluted acids and alkalies.

DIMERSIL 40 is especially suitable for useunder alkaline conditions with good steamresistance. Material has excellent creepresistance and is suitable for applicationswith oils , fuels , alkaline medium andrefrigerants.

Germanischer Lioyd, DVGW, BAM, GOST GOST


F712 111 M6 (M7) F712 110 M6 (M7)

450 450

330 (steam 250) 250 (steam 250)

120 100

1,7-2,0 1,6-1,9

10 9

55 50

32 32

0,04 0,05

3 3

5 5

Temperature (°C)Temperature (°C)

Pres

sure

(bar

)

Pres

sure

(bar

)

-30 00

20

120

100

80

60

40

50 100 150 200 250 300 350 450400

1

3

2

-30 00

20

100

80

60

40

50 100 150 200 250 300 350 450400

1

3

2


temperatura (°C)

priti

sk (b

ar)

temperatura (°C)

priti

sk (b

ar)



www.dimer-group.com

4TESNILNI MATERIALI

Acetilen A A A AAceton B B B BAluminijev klorid A A A AAmoniak B A A AAmonijev hidogenfosfat B A A ABakrov sulfat A A A ABarijev klorid A A A ABenzen B A A ABorova kislina B A A ACikloheksanol B A A ACikloheksanon C B B BDi-butil ftalat A A A ADušik A A A ADušikova kislina 20 % C C C BEtil eter B A A AEtilen A A A AEtilen glikol B A A AFenol C C C CGlicerin A A A AIso-Octane B A A AKalcijev hidroksid B A A AKalijev cianid B A A AKalijev jodid A A A AKerozin B A A AKlor suhi B A A AKloroform C B B BKlorovodikova kislina 20 % C B B AKsilen B A A AMetilen klorid C C C CMineralno olje B A A AMravljična kislina 10 % B A A ANasičena para B A A ANatrijev hidrogen sulfit B A A ANatrijev hidrogenkarbonat B A A ANatrijev hidroksid B B B BNatrijev karbonat A A A ANatrijev klorid A A A ANatrijev sulfat A A A AOcetna kislina 100 % C A A AOgljikov dioksid A A A APetrol B A A APetrolej B A A APitna voda A A A ASilikonsko olje B A A ASladkor A A A ASurova nafta C A A ATerpentin A A A ATetraklometan C B B BToluen C A A ATransformatorsko olje B A A AVinska kislina A A A AVodikov klorid -suh B A A AZemeljski plin A A A AZrak A A A AŽveplena kislina 65% C C C C

DIMERSIL 10 DIMERSIL 20 DIMERSIL 30 DIMERSIL 40


A – primerno za uporabo B – primernost uporabe je odvisna od delovnih pogojevC- neprimerno za uporabo

V kolikor se uporablja medij, ki ni naveden v tabeli, se obrnite na tehnično službo.


www.dimer-group.com

5TESNILNI MATERIALI



Calcium SulphateCarbolic AcidCarbon DioxideCarbon DisulphideCarbon MonoxideCarbon TetrachlorideCastor OilCaustic Soda < 25%Chloracetic AcidChlorine DioxideChlorine DryChlorine LiquidChlorine WetChlormethaneChlorobenzeneChloroformChlorotri�uorideChromic AcidCitric AcidCondensation WaterCooper AcetateCooper SulphateCreosoteCresolCyclohexaneCyclohexanolCyklohexanoneDibenzyl EtherDibutyl PhtalateDiesel OilDiethanolamineDiethylamineDi-iso Butyl KetoneDimethyl FormamideDimethylamineDioxaneEthaneEthanolEthyl AcetateEthyl AcrylateEthyl AlcoholEthyl ChlorideEthyl Chloride DryEthyl EtherEthylbenzeneEthyleneEthylene ChlorideEthylene GlycolFluorine DioxideFluorine GasFluorine LiquidFormaldehydeFormamideFormic Acid 85%Fuel Oil

AAAAAAABAAAAAAAACAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAACCCAAAA

AAAAAAACAAAAAAAACAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAACCCAAAA

AAAAAAAAAAAAAAAACAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAACCCAAAA

DIMERFLON 10 DIMERFLON 11 DIMERFLON 13DIMERGRAF 10 DIMERGRAF 20

white branding white brandingPrinting colour

Description and application DIMERGRAF 10 is basic sheet made of expanded graphite without any insertion. DIMERGRAF 10 is used as a gasketmaterial or as a layering material for campro�le gasketsand as an insert material for double jacketed gaskets.DIMERGRAF 10 sheets are ecellent for handing and cutting.

DIMERGRAF 20 is a graphite laminate (chloride - freeadhesive layer) with one or more �at - 0,05 mm thickstainless steel 316 insertion. DIMERGRAF 20 is generalservice material for high pressure and high temperatureapplications including steam. This material is mainly usedin chemical , petrochemical and other industries.

Marking according to DIN 28 091-4

Thickness mm

No. of inserts ps

Thickness of insertion mm

Material of insertion DIN/ASTM

GR-10 GR-10-O-1 K-Cr

BAM, DVGW, KTW BAM, DVGW

1,0 x 1,0 1,0 x 1,0

1,0 1,5 2,0 3,0 0,75 1,0 1,5 2,0 3,0

Approvals

Sheet size m

- 1 1 1 1 2

- 0,05

Max. temperature * °C

Max. pressure * bar

Density g/cm3

Compressibility ASTM F 36A-66 %

Recovery ASTM F 36A-66 %

Residual stress DIN 52 913, 16h/300°C N/mm2

Ash content ** DIN 51 903 %

without insertion 1,4401/SS316 (�at)

from -200 to +450 from -200 to +450

40 140

1,0 1,0

40-50 40-50

> 47 > 45

≤ 2,0 ≤ 2,0

10-15 10-15

Chloride content** ppm

Gas permeability cm3/min

Spec. leak rate λ mg/s/m

Gasket factors (bD = 20 mm) DIN E 2505

≤ 50 ≤ 50

< 0,05 <0,08 <0,10 <0,15 ≤ 0,06

< 0,30 <0,60 <0,80 <0,85 ≤ 0,60

σ vu N/mm2 20 10

m DIN factor

σvo N/mm2

σ 80 at 300°C N/mm2

ASTM factor m

1,3 1,3

140 120 100 80 60

2 2

160 140 120 100 100

ASTM factor y psi 1500 900

40

100 150 200 250 300 350 400 50000

20

10

30

50

1

3

2

40

60

80

100

120

140

100 150 200 250 300 350 400 450 50000

20

50

1

3

2

Temperature (°C)

Pres

sure

(bar

)

Temperature (°C)

Pres

sure

(bar

)

1 - siutable subject to chemical compactability2 - siutable extended area, technical advice is recommended3 - for this area technical consultation is mandatory

* max. values can not be used simultaneously** if required, the material can be supplied in so-called nuclear grade (in that case ash content is < 0,15% and chloride content < 20 ppm)

Barva tiska Modra Rdeča

Opis in aplikacija


DIMERGRAF 10 je grafitna folija izdelana iz expandiranega grafita brez vložka. DIMERGRAF 10 se uporablja kot samostojni tesnilni material, kot zgornji sloj pri kovinskih profiliranih tesnilih, ali pa kot polnilo pri kovinskih oplaščenih tesnilih. Tesnilne plošče DIMERGRAF 10 so zelo primerne za izdelavo mehkih prirobničnih tesnil.

DIMERGRAF 20 je kompozitni laminat izdelan iz expandiranega grafita in enega ali več kovinskih vložkov iz nerjaveče folije debeline 0,05 mm. DIMERGRAF 20 je zelo primeren za tesnjenje pri visokih temperaturah in pritiskih. Material je posebej primeren za tesnjenje pare in drugih agresivnih medijev. DIMERGRAF 20 se najpogosteje uporablja v kemični in petrokemični industriji.

Oznaka po standardu DIN 28 091-4 GR-10 GR-10-O-1 K-Cr

Certifikat BAM, DVGW BAM, DVGW

Dimenzija plošče m 1,5 x 1,5 1,5 x 1,5

Debelina mm 0,5 0,8 1,0 1,5 2,0 3,0 1,0 1,5 2,0 3,0

Število vložkov kos - 1 1 1 1 2

Deb.kovinskega vložka mm - 0,05

Material kovinskega vložka DIN/ASTM brez vložka 1.4401/SS316 (gladka pločevina)

Max. delovna temperatura * °C od -200 do +550 od -200 do +550

Max. delovni pritisk * bar 80 150

Spec.gostota g/cm³ 1,0 1,0

Stisljivost (ASTM F 36A-66) % 40 - 50 40 - 50

Povratna stisljivost (ASTM F 36A-66) % 10 - 15 10 - 15

Zaostanek napetosti(DIN 52 913, 16h/300°C) N/mm² > 47 > 45

Vsebnost pepela ** (DIN 51 903) % ≤ 2,0 ≤ 2,0

Vsebnost kloridov** ppm ≤ 50 ≤ 50

Plinoprepustnost cm³/min < 0,30 <0,60 <0,80 <0,85 ≤ 0,60

Specifična tesnost λ mg/s/m < 0,05 <0,08 <0,10 <0,15 ≤ 0,06

Tesnilni faktorji (bD = 20 mm) DIN E 2505

σ vu N/mm² 20 10

m DIN factor 1,3 1,3

σvo N/mm² 160 140 120 100 100

σ 80 at 300°C N/mm² 140 120 100 80 60

ASTM faktor m 2 2

ASTM faktor y psi 1500 900



** Material je na voljo tudi v takoimenovani nuklearni kvaliteti z vsebnostjo pepela < 0,15% in vsebnostjo kloridov < 20 ppm

200

180

160

140

120

100

80

60

40

20

0



Calcium SulphateCarbolic AcidCarbon DioxideCarbon DisulphideCarbon MonoxideCarbon TetrachlorideCastor OilCaustic Soda < 25%Chloracetic AcidChlorine DioxideChlorine DryChlorine LiquidChlorine WetChlormethaneChlorobenzeneChloroformChlorotri�uorideChromic AcidCitric AcidCondensation WaterCooper AcetateCooper SulphateCreosoteCresolCyclohexaneCyclohexanolCyklohexanoneDibenzyl EtherDibutyl PhtalateDiesel OilDiethanolamineDiethylamineDi-iso Butyl KetoneDimethyl FormamideDimethylamineDioxaneEthaneEthanolEthyl AcetateEthyl AcrylateEthyl AlcoholEthyl ChlorideEthyl Chloride DryEthyl EtherEthylbenzeneEthyleneEthylene ChlorideEthylene GlycolFluorine DioxideFluorine GasFluorine LiquidFormaldehydeFormamideFormic Acid 85%Fuel Oil

AAAAAAABAAAAAAAACAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAACCCAAAA

AAAAAAACAAAAAAAACAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAACCCAAAA

AAAAAAAAAAAAAAAACAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAACCCAAAA

DIMERFLON 10 DIMERFLON 11 DIMERFLON 13DIMERGRAF 10 DIMERGRAF 20

white branding white brandingPrinting colour

Description and application DIMERGRAF 10 is basic sheet made of expanded graphite without any insertion. DIMERGRAF 10 is used as a gasketmaterial or as a layering material for campro�le gasketsand as an insert material for double jacketed gaskets.DIMERGRAF 10 sheets are ecellent for handing and cutting.

DIMERGRAF 20 is a graphite laminate (chloride - freeadhesive layer) with one or more �at - 0,05 mm thickstainless steel 316 insertion. DIMERGRAF 20 is generalservice material for high pressure and high temperatureapplications including steam. This material is mainly usedin chemical , petrochemical and other industries.


Thickness mm

No. of inserts ps



GR-10 GR-10-O-1 K-Cr

BAM, DVGW, KTW BAM, DVGW

1,0 x 1,0 1,0 x 1,0

1,0 1,5 2,0 3,0 0,75 1,0 1,5 2,0 3,0

Approvals

Sheet size m

- 1 1 1 1 2

- 0,05


Max. pressure * bar

Density g/cm3





without insertion 1,4401/SS316 (�at)

from -200 to +450 from -200 to +450

40 140

1,0 1,0

40-50 40-50

> 47 > 45

≤ 2,0 ≤ 2,0

10-15 10-15





≤ 50 ≤ 50

< 0,05 <0,08 <0,10 <0,15 ≤ 0,06

< 0,30 <0,60 <0,80 <0,85 ≤ 0,60

σ vu N/mm2 20 10

m DIN factor

σvo N/mm2

σ 80 at 300°C N/mm2

ASTM factor m

1,3 1,3

140 120 100 80 60

2 2

160 140 120 100 100

ASTM factor y psi 1500 900

40

100 150 200 250 300 350 400 50000

20

10

30

50

1

3

2

40

60

80

100

120

140

100 150 200 250 300 350 400 450 50000

20

50

1

3

2

Temperature (°C)

Pres

sure

(bar

)

Temperature (°C)

Pres

sure

(bar

)



DIMERGRAF 10 DIMERGRAF 20

TESNILNI MATERIALI IZ EKSPANDIRANEGA GRAFITA

temperatura (°C)

priti

sk (b

ar)

temperatura (°C)

priti

sk (b

ar)


www.dimer-group.com

6TESNILNI MATERIALI

Barva tiska Zelena Bela

Opis in aplikacija


DIMERGRAF 21 je kompozitni laminat izdelan iz ekspandiranega grafita in kovinske folije iz niklja. DIMERSIL 21 je namenjen za tesnjenje v srednje zahtevnih pogojih. Material je zelo primeren za rokovanje in izdelavo mehkih prirobničnih tesnil.

DIMERGRAF 30 je kompozitni laminat izdelan iz ekspandiranega grafita in enega ali več kovinskih vložkov iz perforirane nerjaveče folije debeline 0,05 mm, brez uporabe lepila. Material se uporablja za izdelavo prirobničnih tesnil z uporabo v najzahtevnejših pogijih. DIMERGRAF 30 je zelo primeren za tesnjenje pare in kemikalij v parovodih, kemični in pare petrokemični industriji ter predelovalni industriji.

Oznaka po standardu DIN 28 091-4 GR-10-O-1 K-Ni GR-10-O-1 M-Cr

Certifikat BAM, DVGW

Dimenzija plošče m 1,5 x 1,5 1,5 x 1,5

Debelina mm 1,0 1,5 2,0 3,0 1,0 1,5 2,0 3,0

Število vložkov kos 1 1 1 1 1

Deb.kovinskega vložka mm 0,013 0,10

Material kovinskega vložka DIN/ASTM Nikelj 2.4066 (gladka pločevina) 1.4401/SS316 (perforirana pločevina)



Spec.gostota g/cm³ 1,0 1,0

Stisljivost (ASTM F 36A-66) % 40 - 50 30 - 40

Povratna stisljivost (ASTM F 36A-66) % 10 - 15 15 - 20

Zaostanek napetosti(DIN 52 913, 16h/300°C) N/mm² > 45 >48 >48 >48 >48

Vsebnost pepela ** (DIN 51 903) % ≤ 2,0 ≤ 2,0

Vsebnost kloridov** ppm ≤ 50 ≤ 50

Plinoprepustnost cm³/min ≤ 0,80 < 0,60 <0,60 <0,80 <1,00

Specifična tesnost λ mg/s/m ≤ 0,08 < 0,06 <0,06 <0,08 <0,10

Tesnilni faktorji (bD = 20 mm) DIN E 2505

σ vu N/mm² 10 20

m DIN factor 1,3 1,3

σvo N/mm² 110 180 160 140 120

σ 80 at 300°C N/mm² 100 160 140 120 100

ASTM faktor m 3 3 3 2,5 2,5

ASTM faktor y psi 1000 9000 9000 4000 4000



** Material je na voljo tudi v takoimenovani nuklearni kvaliteti z vsebnostjo pepela < 0,15% in vsebnostjo kloridov < 20 ppm



AcetaldehydeAcetamideAcetic AcidAcetic Acid GlacialAcetic AnhydrideAcetoneAcetonitrileAcetyl ChlorideAcetyleneAcrylic AcidAcrylonitrileAdipic AcidAirAllyl ChlorideAlumAluminium AcetateAluminium ChlorideAluminium Hydroxide (Solid) Aluminium SulphateAmmonia GasAmmonium CarbonateAmmonium ChlorideAmmonium HydroxideAmmonium SulphateAmyl AcetateAmyl AlcoholAnilineAqua RegiaAsphaltAviation FuelBarium ChlorideBenzaldehydeBenzeneBenzoic AcidBenzonitrileBenzyl AlcoholBenzyl ChlorideBlast Furnace GasBleach solutionBoiler Feed WaterBoraxBoric AcidBrineBromineButadieneButaneButanolButyl AcetateButyl AlcoholButyl MethacrylateButylamineButyric AcidCalcium ChlorideCalcium HydroxideCalcium Hypochlorite

AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA




Printing colour

Description and application

DIMERGRAF 30

white branding

DIMERGRAF 30 is reinforced with a single insertions oftanged 0,1mm thick 316 stainless steel for improvedblow-out resistance. No adhesive is used to bond thegraphite layers. This sheet is used frequently in �angeconnections for piping, vessel application and othermachinery. It is suitable for steam systems, chemical,petrochemical industries , processing industry , etc.

GR-10-O-1 M-Cr

BAM, DVGW

1,5 x 1,5

1,0 1,5 2,0 3,0

1 1 1 1

0,10

1.4401/SS316 (tanged)

from -200 to +450

140

1,0

30-40

>48 >48 >48 >48

≤ 2,0

15-20

≤ 50

< 0,06 <0,06 <0,08 <0,10

< 0,60 <0,60 <0,80 <1,00

20

1,3

160 140 120 100

3 3 2,5 2,5

180 160 140 120

9000 9000 4000 4000

white branding

DIMERGRAF 21 is made of pure expanded exfoliatedgraphite, reinforced with �at nickel insertion.

DIMERGRAF 21 is designed for middle workingparameters. Material is excellent for easy handing andcutting.

GR-10-O-1 K-Ni

1,0 x 1,0

1,0 1,5 2,0 3,0

1

0,013***

Nickel 2.4066 (�at)

from -200 to +450

120

1,0

40-50

> 45

≤ 2,0

10-15

≤ 50

≤ 0,08

≤ 0,80

10

1,3

100

3

110

1000

DIMERGRAF 21

40

60

80

100

120

100 150 200 250 300 350 400 500Temperature (°C)

Pres

sure

(Bar

)

00

20

50

1

3

2

40

60

80

100

120

140

100 150 200 250 300 350 400 450 500Temperature (°C)

Pres

sure

(Bar

)

00

20

50

1

3

2


Thickness mm

No. of inserts ps



Approvals

Sheet size m


Max. pressure * bar

Density g/cm3









σ vu N/mm2

m DIN factor

σvo N/mm2

σ 80 at 300°C N/mm2

ASTM factor m

ASTM factor y psi






AcetaldehydeAcetamideAcetic AcidAcetic Acid GlacialAcetic AnhydrideAcetoneAcetonitrileAcetyl ChlorideAcetyleneAcrylic AcidAcrylonitrileAdipic AcidAirAllyl ChlorideAlumAluminium AcetateAluminium ChlorideAluminium Hydroxide (Solid) Aluminium SulphateAmmonia GasAmmonium CarbonateAmmonium ChlorideAmmonium HydroxideAmmonium SulphateAmyl AcetateAmyl AlcoholAnilineAqua RegiaAsphaltAviation FuelBarium ChlorideBenzaldehydeBenzeneBenzoic AcidBenzonitrileBenzyl AlcoholBenzyl ChlorideBlast Furnace GasBleach solutionBoiler Feed WaterBoraxBoric AcidBrineBromineButadieneButaneButanolButyl AcetateButyl AlcoholButyl MethacrylateButylamineButyric AcidCalcium ChlorideCalcium HydroxideCalcium Hypochlorite





Printing colour


DIMERGRAF 30

white branding

DIMERGRAF 30 is reinforced with a single insertions oftanged 0,1mm thick 316 stainless steel for improvedblow-out resistance. No adhesive is used to bond thegraphite layers. This sheet is used frequently in �angeconnections for piping, vessel application and othermachinery. It is suitable for steam systems, chemical,petrochemical industries , processing industry , etc.

GR-10-O-1 M-Cr

BAM, DVGW

1,5 x 1,5

1,0 1,5 2,0 3,0

1 1 1 1

0,10

1.4401/SS316 (tanged)

from -200 to +450

140

1,0

30-40

>48 >48 >48 >48

≤ 2,0

15-20

≤ 50

< 0,06 <0,06 <0,08 <0,10

< 0,60 <0,60 <0,80 <1,00

20

1,3

160 140 120 100

3 3 2,5 2,5

180 160 140 120

9000 9000 4000 4000

white branding

DIMERGRAF 21 is made of pure expanded exfoliatedgraphite, reinforced with �at nickel insertion.

DIMERGRAF 21 is designed for middle workingparameters. Material is excellent for easy handing andcutting.

GR-10-O-1 K-Ni

1,0 x 1,0

1,0 1,5 2,0 3,0

1

0,013***

Nickel 2.4066 (�at)

from -200 to +450

120

1,0

40-50

> 45

≤ 2,0

10-15

≤ 50

≤ 0,08

≤ 0,80

10

1,3

100

3

110

1000

DIMERGRAF 21

40

60

80

100

120

100 150 200 250 300 350 400 500Temperature (°C)

Pres

sure

(Bar

)

00

20

50

1

3

2

40

60

80

100

120

140

100 150 200 250 300 350 400 450 500Temperature (°C)

Pres

sure

(Bar

)

00

20

50

1

3

2


Thickness mm

No. of inserts ps



Approvals

Sheet size m


Max. pressure * bar

Density g/cm3









σ vu N/mm2

m DIN factor

σvo N/mm2

σ 80 at 300°C N/mm2

ASTM factor m

ASTM factor y psi



DIMERGRAF 21 DIMERGRAF 30

temperatura (°C)

priti

sk (b

ar)

temperatura (°C)

priti

sk (b

ar)


www.dimer-group.com

7TESNILNI MATERIALI


Acetilen A A A AAceton A A A AAdipinska kislina A A A AAlum A A A AAluminijev klorid A C C CAmoniak A A A AAmonijev hidrogenfosfat A A A AAmonijev hidroksid A A A AAmonijev klorid A B B BAnilin A A A AAqua regia C C C CAsfalt A A A ABakrov sulfat A A A ABarijev klorid A A A ABenzen A A A ABorova kislina A A A AButan A A A AButil alkohol A A A ACikloheksanol A A A ACikloheksanon A A A ADibutil ftalat A A A ADušik A A A ADušikova kislina 20% A A A ADušikova kislina do 65% B B B BDušikova kislina nad 85% C C C CEtan A A A AEtil acetat A A A AEtil alkohol A A A AEtil eter A A A AEtil klorid A A A AEtilen A A A AEtilenglikol A A A AFenol A A A AFluor - plin B C C CFluor dioksid C C C CFluor tekoči C C C CFluorovodikova kislina (do 40 %) B C C CFormaldehid A A A AFosforjeva kislina 95 % A A A AGlicerin A A A AGorivo A A A AIzo oktan A A A AIzopropilni alkohol A A A AKalcijev hidroksid A A A AKalcijev hipoklorid A B B BKalcijev sulfat A A A AKalijev dikromat B C C CKalijev cianid A A A Akalijev jodid A A A AKalijev klorid A A A AKalijev nitrat B C C CKerozin A A A AKisik (do 350°C) B C C C

DIMERGRAF 10 DIMERGRAF 20 DIMERGRAF 21 DIMERGRAF 30


www.dimer-group.com

8TESNILNI MATERIALI



Klor - suhi A A A AKlor tekoči C C C CKlorirana voda C C C CKlormetan A A A AKloroform A A A AKlorovodikova kislina 20% B C C CKromova kislina (do 20%) A A A AKsilene A A A AKurilno olje A A A AMetilen klorid A A A AMineralno olje A A A AMorska voda A A A AMotorno olje A A A ANaravni plin A A A ANasičena para A A A ANatrijev hidrogen karbonat A A A ANatrijev hidroksid B C C CNatrijev karbonat A A A ANatrijev klorid A B B BNatrijev sulfat A A A ANitrobenzen A A A AOcetna kislina 100 % A A A AOdpadna voda A A A AOgljikov dioksid A A A AOgljikov disulfid A A A AOksalna kislina B C C CParafin A A A APitna voda A A A APlin utekočinjen A A A ARaztopina mila A A A ASilikonsko olje A A A ASladkor A A A ASuhi vodikov klorid A A B ASurova nafta A A A ATerpentin A A A ATetraklormetan A A A ATetrakloretan A A A AToluen A A A AVinilklorid A A A AVinska kislina A B B BVoda A A A AVodik A A A AVodikov florid A C C CVodikov klorid A A A AVodikov klorid tekoči A C C CVodikov peroksid 6% A A A AZrak A A A AŽveplena kislina 30% A B B BŽveplena kislina 70% A C C C

A – primerno za uporabo B – primernost uporabe je odvisna od delovnih pogojevC- neprimerno za uporabo


www.dimer-group.com

9TESNILNI MATERIALI

Barva Svetlo modra Roza

Opis in aplikacija


DIMERFLON 10 je visokokvalitetni PTFE tesnilni material z biaksialno orientiranimi vlakni in je zaradi svoje sestave idealna izbira za tesnjenje neravnih prirobničnih spojev. DIMERFLON 10 je namenjen za tesnjenje prirobnic z nizkim površinskim pritiskom. Tipična uporaba je tesn-jenje steklenih, keramičnih ali plastičnih ter ner-avnih prirobnic. DIMERFLON 10 je odporen na skoraj vse kemične medije v območju PH (0-14), z izjemo voidikovega florida, fluora v plinskem stanju. Material je zaradi svoje trdnosti in fleksi-bilnosti idealen za rokovanje in sekanje tesnil.

DIMERFLON 11 je visokokvalitetni PTFE tesnilni material z biaksialno orientiranimi vlakni in polnilom iz silike. Splona uporaba materiala je tesnjenje vseh medijev na celotnem ombočju PH (0-14). DIMERFLON 11 je posebej primeren za tesnjenje močnih kislin in lugov. Poleg tega se material uporablja tudi za tesnjenje topil, goriv, vode, pare in klorovih spojin. Material je zaradi svoje trdnosti in fleksibilnosti idealen za rokovanje in sekanje tesnil.

Označevanje po standardu (DIN 28 091-3) TF-G-O TF-M-O

Certifikati FDA FDA, BAM

Dimenzija plošč m 1,5 x 1,5 1,5 x 1,5

pH 0 - 14 0 - 14



Gostota g/cm³ 1,4 2,2

Stisljivost (ASTM F 36) % 41 10

Povratna stisljivost (ASTM F 36) % 37 41

Zaostanek napetosti (DIN 52913, 175° C) MPa 33 31

Natezna trdnost (ASTM F 152) MPa 11 15

Lezenje (ASTM F 38) % 31 35

Tesnost (DIN 3535/6) mg/sm < 0,002 < 0,002

Tesnost tekočin (ASTM F 37) mL/h / /





DIMERFLON 10 DIMERFLON 11

Light blue Pink

DIMERFLON 10 is a superior performance biaxiallyorientated PTFE sheet sealing material with moreconformable properties, ideally suited to irregular �anges.DIMERFLON 10 is speci�cally designed for use in low boltloated �anges. Typical �anges include glass lined, ceramicor plastic coated or uneven and badly distored �anges.DIMERFLON 10 is suitable for chemical media acrosspH (0 - 14) range, with exception of melting alcali metals,�uorine gas, hydrogen �uoride. The sheets are excellentfor handling and cutting.

DIMERFLON 11 is a superior performance biaxiallyorientated PTFE sheet sealing material with silica �ller.A general purpose grade for sealing applications acrossthe whole pH (0 -14) range. DIMERFLON 11 is particularysuitable for use with strong acids hydro�uoric acid andalkalis. Other applications include solvents, fuels, water,steam and chlorine compounds. The sheets are excellentfor handling and cutting.

TF-G-O TF-M-O

FDA FDA, BAM

1,0 x 1,0 1,5 x 1,5 2,0 x 2,0 1,0 x 1,0 1,5 x 1,5 2,0 x 2,0

0,75 1,0 1,5 2,0 2,5 3,0 0,75 1,0 1,5 2,0 2,5 3,0

from -200 to +260 from -200 to +260

85 85

1.4 2.2

40 7

30 40

25 32

35 23

< 0,02 < 0,01

11 15

0.23 0.21

Colour



Thickness mm


Max. pressure * bar

Density g/cm³

Certi�cate

Sheet size m

Compressibility (ASTM F 36) %

Recovery (ASTM F 36) %

Residual stress (BS 7531, 175° C) MPa

Tensile strenght (ASTM F 152) MPa

Creep relaxation (ASTM F 38) %

Gas pemeability (DIN 3535) cm³/min

1 - suitable subject to chemical compactability2 - suitable in some cases but check your application requirements with the technical team3 - this area technical consultation is mandatory

Liquid leakage (ASTM F 37) mL/hod

* max. values can not be used simultaneously

40

60

80

100

120

100 150 200 250 300 350 40000

20

50

1

3

2

40

60

80

100

120

100 150 200 250 300 350 40000

20

50

1

32

Temperature (°C)

Pres

sure

(bar

)

Temperature (°C)

Pres

sure

(bar

)

ChloroformChromic acid (up to 20%)Iso-OctaneIsopropyl alcoholKeroseneMethylene chlorideNitric acid 20%Nitric acid (over 85%)Nitric acid (up to 65%)NitrobenzeneNitrogenOil crude naphtaOil heatingOil hydraulic mineralOil motorOil siliconOil transformerOxalic acidOxygen (up to 350°C)Para�nPetrolPhenolPhospohoric acid 95%Potassium cyanidePotassium dichromatePotassium chloridePotassium iodidePotassium nitrateSoap solutionsSodium carbonateSodium hydrogen carbonateSodium hydroxideSodium chlorideSodium sulphateSteam saturatedSugarSulphuric acid 30%Sulphuric acid 70%Tartaric acidTetrachlorethaneTetrachlormethaneTolueneTurpentineVinyl chlorideWaterWater chlorinatedWater potableWater seaWater wasteXylene

ABAAAAACBAAAAAAAABAAAAAABAABAAABAAAAAAAAAAAAAAAAAA

ACAAAAACBAAAAAAAACAAAAAACAACAAACBAAABCBAAAAAAAAAAA




A - suitable for applicationB - suitability depends on operating conditionsC - not suitable

TESNILNI MATERIALI IZ PTFE S POLNILI




Light blue Pink

DIMERFLON 10 is a superior performance biaxiallyorientated PTFE sheet sealing material with moreconformable properties, ideally suited to irregular �anges.DIMERFLON 10 is speci�cally designed for use in low boltloated �anges. Typical �anges include glass lined, ceramicor plastic coated or uneven and badly distored �anges.DIMERFLON 10 is suitable for chemical media acrosspH (0 - 14) range, with exception of melting alcali metals,�uorine gas, hydrogen �uoride. The sheets are excellentfor handling and cutting.

DIMERFLON 11 is a superior performance biaxiallyorientated PTFE sheet sealing material with silica �ller.A general purpose grade for sealing applications acrossthe whole pH (0 -14) range. DIMERFLON 11 is particularysuitable for use with strong acids hydro�uoric acid andalkalis. Other applications include solvents, fuels, water,steam and chlorine compounds. The sheets are excellentfor handling and cutting.

TF-G-O TF-M-O

FDA FDA, BAM

1,0 x 1,0 1,5 x 1,5 2,0 x 2,0 1,0 x 1,0 1,5 x 1,5 2,0 x 2,0

0,75 1,0 1,5 2,0 2,5 3,0 0,75 1,0 1,5 2,0 2,5 3,0

from -200 to +260 from -200 to +260

85 85

1.4 2.2

40 7

30 40

25 32

35 23

< 0,02 < 0,01

11 15

0.23 0.21

Colour



Thickness mm


Max. pressure * bar

Density g/cm³

Certi�cate

Sheet size m










40

60

80

100

120

100 150 200 250 300 350 40000

20

50

1

3

2

40

60

80

100

120

100 150 200 250 300 350 40000

20

50

1

32

Temperature (°C)

Pres

sure

(bar

)

Temperature (°C)

Pres

sure

(bar

)

ChloroformChromic acid (up to 20%)Iso-OctaneIsopropyl alcoholKeroseneMethylene chlorideNitric acid 20%Nitric acid (over 85%)Nitric acid (up to 65%)NitrobenzeneNitrogenOil crude naphtaOil heatingOil hydraulic mineralOil motorOil siliconOil transformerOxalic acidOxygen (up to 350°C)Para�nPetrolPhenolPhospohoric acid 95%Potassium cyanidePotassium dichromatePotassium chloridePotassium iodidePotassium nitrateSoap solutionsSodium carbonateSodium hydrogen carbonateSodium hydroxideSodium chlorideSodium sulphateSteam saturatedSugarSulphuric acid 30%Sulphuric acid 70%Tartaric acidTetrachlorethaneTetrachlormethaneTolueneTurpentineVinyl chlorideWaterWater chlorinatedWater potableWater seaWater wasteXylene

ABAAAAACBAAAAAAAABAAAAAABAABAAABAAAAAAAAAAAAAAAAAA





A - suitable for applicationB - suitability depends on operating conditionsC - not suitable


priti

sk (b

ar)

temperatura (°C)

priti

sk (b

ar)

temperatura (°C)


www.dimer-group.com

10TESNILNI MATERIALI

Barva Bela

Opis in aplikacija


DIMERFLON 13 je visokokvalitetni PTFE tesnilni material z biaksialno orientiranimi vlakni in pol-nilom iz barijevega sulfata. Splona uporaba ma-teriala je tesnjenje vseh medijev na celotnem ombočju PH (0-14). DIMERFLON 13 je posebej primeren za tesnjenje fluorovodikove kisline, vendar ne začisti tekoči fluorovodik. Poleg tega se material uporablja tudi za tesnjenje lugov, topil, goriv, vode, pare in klora. Material je zaradi svoje trdnosti in fleksibilnosti idealen za rokovanje in sekanje tesnil.

Označevanje po standardu (DIN 28 091-3) TF-Z-O

Certifikati FDA, BAM

Dimenzija plošč m 1,5 x 1,5

pH 0 - 14

Max. delovna temperatura * °C od -200 do +260

Max. delovni pritisk * bar 85

Gostota g/cm³ 2,0

Stisljivost (ASTM F 36) % 12

Povratna stisljivost (ASTM F 36) % 40

Zaostanek napetosti (DIN 52913, 175° C) MPa 31

Natezna trdnost (ASTM F 152) MPa 17

Lezenje (ASTM F 38) % 33

Tesnost (DIN 3535/6) mg/sm < 0,002

Tesnost tekočin (ASTM F 37) mL/h 0,22





DIMERFLON 13

white

DIMERFLON 13 is a high performance biaxially orientatedPTFE sheet material with barium sulphate �ller. A generalpurpose grade for sealing applications across the whole pH(0 -14) range. It is suitable for use with hydro�uoric acid,but not pure liquid hydrogen �uoride. DIMERFLON 13 canalso be used with alkalis, solvents, fuels, water, steam andchlorine. The sheets are excellent for handling and cutting.

TF-Z-O

FDA, BAM

1,0 x 1,0 1,5 x 1,5 2,0 x 2,0

0,75 1,0 1,5 2,0 2,5 3,0

from -200 to +260

85

3.0

5

40

30

21

< 0,01

14

0.22

40

60

80

100

120

100 150 200 250 300 350 40000

20

50

1

32

Temperature (°C)

Pres

sure

(bar

)



Colour



Thickness mm


Max. pressure * bar

Density g/cm³

Certi�cate

Sheet size m








Acetic acid 100%AcetoneAcetyleneAdipic acidAirAlumAluminium chlorideAmmoniaAmmonium hydrogenphospateAmmonium hyroxideAmmonium chlorideAnilineAqua regiaAsphaltBarium chlorideBenzeneBoric acidButaneButyl alcoholCalcium hydroxideCalcium hypochlorideCalcium sulphateCarbon dioxideCarbon disulphideCopper sulphateCyclohexanolCyklohexanonDi-butyl phtalateEthaneEthyl acetateEthyl alcoholEthyl etherEthyl chlorideEthylenEthylene glycolFluorine dioxideFluorine gasFluorine liquidFormaldehydeFuel aviationGas LPGGas naturalGlycerineHydro�uoric acid (up to 40 %)HydrogenHydrogen �uorideHydrogen chlorideHydrogen chloride dryHydrogen chloride wetHydrogen peroxide 6%Hydrochlorid acid 20%Chlorine dryChlorine waterChlorine wetChlormethane

AAAAAAAAAAAACAAAAAAAAAAAAAAAAAAAAAACBCAAAAABAAAAAABACCA

AAAAAACAAABACAAAAAAABAAAAAAAAAAAAAACCCAAAAACACAACACACCA

AAAAAACAAABACAAAAAAABAAAAAAAAAAAAAACCCAAAAACACABCACACCA


AAAAAACAAABACAAAAAAABAAAAAAAAAAAAAACCCAAAAACACAACACACCA


DIMERFLON 13

priti

sk (b

ar)

temperatura (°C)


www.dimer-group.com



Acetaldehid A A AAcetamid A A AAcetil Klorid A A AAcetilen A A AAcetonitrile A A AAcetonnitril A A AAdipinska kislina A A AAkrilna kislina A A AAkrilonitril A A AAlil klorid A A AAliminijev klorid A A AAlumimijec acetat A A AAluminij A A AAluminijev hidroksid (trdno stanje) A A AAluminijev sulfat A A AAmil acetat A A AAmil alkohol A A AAmoniak A A AAmonijev hidroksid A A AAmonijev karbonat A A AAmonijev klorid A A AAmonijev sulfat A A AAnhidrid maleinske kisline A A AAnhidrid ocetne kisline A A AAnilin A A AAsfalt A A ABakrov acetat A A ABakrov sulfat A A ABarijev klorid A A ABelilo A A ABencin A A ABencin A A ABenzen A A ABenzen aldehid A A ABenzil alkohol A A ABenzil klorid A A ABenzojska kislina A A ABenzonitrile A A ABoraks A A ABorova kislina A A ABrom A A AButadien A A AButan A A AButanol A A AButil acetat A A AButil alkohol A A AButil metakrilat A A AButilamin A A ACiklohehsanol A A ACikoheksan A A ACikoheksanon A A ACinkov klorid A A ACinkov sulfat A A ACitronska kislina A A ADibenzil eter A A ADibutil ftalat A A ADiesel A A A

DIMERFLON10 DIMERFLON 11 DIMERFLON 13


www.dimer-group.com



Dietanolamin A A ADietilamin A A ADi-iso butil etanol A A ADimetil formamid A A ADimetilamin A A ADioksan A A ADušik A A ADušikova hidroklorna kislina A A ADušikova kislina A A AEtan A A AEtanol A A AEtil acetat A A AEtil akrilat A A AEtil eter A A AEtil klorid A A AEtil klorid suhi A A AEtilalkohol A A AEtilbenzen A A AEtilen A A AEtilen glikol A A AEtilen klorid A A AFenol A A AFluor plin C C CFluorov dioksid C C CFluorovodikova kislina > 65% C C BFor A A AFormaldehid C C CFormamid A A AFosforna kislina <45% A A AFosforna kislina >45% B B AFosgen A A AFtalna kislina A A AFuorovodikova kislina <65% C C AGlicerin A A AGlikol A A AGlukoza A A AHeksan A A AHeptan A A AHidravlično mineralno olje A A AHidravlično olje A A AHladilna tekočina A A AHydrofluosillicic Acid C C BIzo-oktan A A AIzopropil acetat A A AIzopropil alkohol A A AIzopropil eter A A AKalcijev hidroksid A A AKalcijev hipoklorit A A AKalcijev klorid A A AKalcijev sulfat A A AKalijev acetat A A AKalijev bikromat <20% A A AKalijev cianid A A AKalijev hidroksid < 50% C C AKalijev hipoklorid A A A



www.dimer-group.com



Kalijev karbonat A A AKalijev klorat A A AKalijev klorid A A AKalijev nitrat A A AKarbonska kislina A A AKatran A A AKerozin A A AKisik C A AKlor mokri A A AKlor suhi A A AKlor tekoči A A AKloracetanhidridna kislina A A AKlorobenzen A A AKloroform A A AKlorometan A A AKlorotrifluorid C C CKlorov dioksid A A AKlorovodikova kislina 37% A A AKondenzirana voda A A AKreozot A A AKresin A A AKrezol A A AKromova kislina A A AKsilen A A AKurilno olje A A ALaneno olje A A AMagnezijev sulfat A A AMaleinska kislina A A AMaslena kislina A A AMetan A A AMetanol A A AMetil alkohol A A AMetil klorid A A AMetil metakrilat A A AMetilen klorid A A AMetiletil keton A A AMilo A A AMineralno olje A A AMlečna kislina A A AMorska voda A A AMotorno olje A A AMotorno olje A A AMravljična kislina 85% A A ANafta A A ANaftalin A A ANatrijev aluminat A A ANatrijev bikarbonat A A ANatrijev bisulfid A A ANatrijev cianid A A ANatrijev hidroksid < 25% B C ANatrijev hidroksid < 50% B C ANatrijev karbonat A A ANatrijev klorid A A ANatrijev silikat A A ANatrijev sulfat A A A



www.dimer-group.com



Natrijev sulfid A A ANikljev klorid A A ANikljev sulfat A A ANitrobenzen A A ANizkotlačna para A A AOcetna kislina A A AOcetna kislina zmznjena A A AOgljikov dioksid A A AOgljikov disulfid A A AOgljikov monoksid A A AOgljikov tetraklorid A A AOksalna kislina A A AOktan A A AOlje oljne ogrščice A A AOlje za mazanje A A AOlje za reduktorje A A APalmitinska kislina A A APara A A AParafin A A APentan A A APerkloretilen A A APerkloretilen A A APetrolej A A APiridin A A APitna voda A A APlavžni plin A A APlin za generatorje A A APlinsko olje A A APropan A A ARastlinsko olje A A ARdeča dušikova kislina A A ARicinusovo olje A A ASalicinska kislina A A ASilikonsko olje A A ASladkor A A ASlanica A A ASrebrov nitrat A A AStearinska kislina A A AStiren A A ASurova nafta A A AŠkrob A A ATaninska kislina A A ATermalno olje A A ATermalno olje A A ATerpentin A A ATetrakloetilen A A ATetrakloretan A A AToluen A A ATransformatorsko olje A A ATrikloretilen A A AUtekočinjen naftni plin A A AUtekočinjen plin LPG A A AVinil acetat A A AVinil bromid A A AVinil klorid A A A



www.dimer-group.com



Vinska kislina A A AVisokotlačna para B B BVoda A A AVoda - kotlovnica A A AVodik A A AVodikov florid C C CVodikov klorid A A AVodikov klorid suhi A A AVodikov peroksid 6% A A AVodikov sulfid A A AWhite Spirit A A AZemeljski plin A A AZrak A A AŽganje A A AŽveplena kislina A A AŽveplena kislina (dim) A A CŽveplena kislina 96% A A AŽveplo A A AŽveplov dioksid suhi A A AŽveplov trioksid A A A



www.dimer-group.com



Barva

Opis in aplikacija

TEHNIČNI POdATkI

Debelina mm

Max. delovna temperatura * °C

pH

Gostota g/cm³

Stisljivost (ASTM F 36) %

Povratna stisljivost (ASTM F 36) %

Natezna trdnost (ASTM F 152) MPa

Zaostanek napetosti (DIN 52913) Mpa

Plinoprepustnost (DIN 3535/6) mg/sm

Dimenzije mm

Bela

DIMERFLON 20 je izdelan iz čistega PTFE, ki ga odlikuje odlična kemična obstojnost, razen na alkalno taljene kovine in flourove pline. Določene pomanjkljivosti čistega PTFE se lahko izboljšajo z uporabo različnih polnil, kot npr. grafit, bronza in steklena vlakna.

do 50

-240°C do +260°C

0 - 14

0,90

45

14

31

15

0,002

Plošče

1000 x 1000 1200 x 1200 1500 x 1500

Folije

širina do 120, debelina do 1

Palice

od 5 do 300

Cevi

od 6 do 300 (zunanji premer)

Bela

DIMERFLON 30 je večsmerno orientiran ekspandiran PTFE v obliki plošč, z odlično mehansko trdnostjo ter minimalnim lezenjem pri povišanih temperaturah. DIMERFLON 30 je uporaben za tesnjenje skoraj vseh medijev pri širokotemperaturnem območju. Material je čist in netoksičen, zato se lahko uporablja za aplikacije v živilski in farmacevtski industriji.

0,5 do 6,0 / do 9,0 na zahtevo

-240°C do +260°C

0 - 14

0,90

45

14

31

15

0,002

Plošče

1500 x 1500

16

TESNILNI MATERIALI IZ EKSPANDIRANEGA IN ČISTEGA PTFE


www.dimer-group.com


Bela Bela Bela

DIMERFLON ST-U je tesnilni trak izdelan iz 100 % expandiranega PTFE z odličnimi tesnilnimi lastnostmi.Tipična uporaba so tesnjenje prirobnic, ohišja črpalk, kompresorjev, toplotnih izmenjevalcev ter drugih naprav.

DIMERFLON ST-HD je tesnilni trak izdelan iz 100 % ekspanidiranega zgoščenega PTFE z odličnimi tesnilnimi lastnostmi.Tipična uporaba so deformirane (neparalelne) ali poškodovane tesnilne površine toplotnih izmenjevalcev, velikih tankov in rezervoarjev ter ohišja črpalk. Pogosto se uporablja tudi kot tesnilo kotla.

DIMERFLON ST-M je tesnilni trak izdelan iz 100 % expandiranega PTFE z odličnimi tesnilnimi lastnostmi.Tipična uporaba so tesnjenje prirobnic, ohišja črpalk, kompresorjev, toplotnih izmenjevalcev ter drugih naprav.

-240°C do +260°C -240°C do +260°C -240°C do +260°C

0 - 14 0 - 14 0 - 14

0,65 1,00 0,65

Trakovi Trakovi Trakovi

3 x 1,5 3 x 1,5 4 x 2,5

5 x 2 5 x 2 5 x 2

7 x 2,5 7 x 2,5 6 x 4,6

10 x 3 10 x 3 8 x 5,5

12 x 4 12 x 4 10 x 7

14 x 5 14 x 5

17 x 6 17 x 6 ostale dimenzije so na voljo na zahtevo

20 x 7

25 x 5

25 x 10

30 x 10

40 x 5

DIMERFLON ST-U DIMERFLON ST-HD DIMERFLON ST-M


17


www.dimer-group.com


DIMERFLON ST-F DIMERFLON ST-B

Barva

Opis in aplikacija

TEHNIČNI POdATkI

Debelina mm

Max. delovna temperatura * °C

pH

Gostota g/cm³

Stisljivost (ASTM F 36) %

Povratna stisljivost (ASTM F 36) %

Natezna trdnost (ASTM F 152) MPa

Zaostanek napetosti (DIN 52913) Mpa

Plinoprepustnost (DIN 3535/6) mg/sm

Dimenzije mm

Bela

DIMERFLON ST-F je izdelan iz čistega ekspandiranega PTFE in polnil. Kombinacija ekspandiranega PTFE in anorganskih polnil rezultira v izboljšanih lastnostih pri višjih temperaturah in neravnih prirobnicah.

-240°C do +260°C

0 - 14

1,00

Trakovi

6 x 2,5

8 x 3,5

10 x 5

Bela

DIMERFLON ST-B je tesnilni trak namenjen za tesnjenje odprtin pri bojlerjih in kotlih. Večsmerna orientiranost vlaken zagotavlja dolgo življenjsko dobo tesnila.

-240°C do +260°C

0 - 14

0,90

Trakovi

10 x 3 / za tesnilno površino 15 mm

24 x 3 / za tesnilno površino 25 mm

18



www.dimer-group.com


19

Tesnilni materiali iz sljude

Tesnilni materiali iz ekspandiranega grafita

Kalandrirani tesnilni materiali

Tesnilni materiali iz PTFE

Tesnilni materiali iz gume

1000

Površinski pritisk (bar)

Temperatura (°C)

-200

0

200

400

600

800

50 100 150 200

DIAGRAM O UPORABI TESNILNIH MATERIALOV

PALETA IZDELKOVHidravlična tesnilaIndustrijska tesnilaTesnilni materialiMehanska tesnilaPleteniceIzolacijske pletenice in tehnični tekstilStoritve

KONTAKTNI PODATKI

DIMER GROUP V 2012-01 Fotografije: Lilik Aleksander

Dimer s.r.o.Češka republikaZelená 505, 760 01 Zlín-KudlovT: +420 577 224 343F: +420 577 224 007E: [email protected]

Dimer Engineering s.r.o.Češka republikaNa Pohoří 43, 273 53 HostouňT: +420 312 665 000F: +420 312 665 200E: [email protected]

Dimer Slovakia s.r.o.Slovaška republikaTeplárenská 17, 971 01 PrievidzaT: +421 465 430 208F: +421 465 121 310E: [email protected]

Dimer Slovenija d.o.o.SlovenijaBrodarska ulica 14, 1270 Litija T: +386 1 620 08 01F: +386 1 620 08 02E: [email protected]

Documents

TESNILNI MATERIALI - Dimerdimer.si/userfiles/makseal/file/katalogi/DIMER E_Katalog Tesnilni... · Sulphuric Acid 96% Sulphurous Acid Tannic Acid Tar Tartaric Acid Tetrachlorethane