Upload
fjsp69
View
221
Download
4
Embed Size (px)
DESCRIPTION
Titan NVR, guis de ayuda rapida para el nvr titan de marca generica.
Citation preview
The Intelligent Surveillance Solution
Titan NVR
Quick Start Guide
Ver. 1.3.0.120403.00
Table of Contents English ........................................................................................ 1 .......................................................................................... 3 ........................................................................................ 5
Espaol ........................................................................................ 7 Deutsch ....................................................................................... 9 Franais ..................................................................................... 11 Ialiano ....................................................................................... 13 P ..................................................................................... 15 etina ...................................................................................... 17 ........................................................................................ 19
Polski ......................................................................................... 21 Nederlands ................................................................................ 23 Svenska ..................................................................................... 25 Portugus (Brasil) ........................................................................ 27 Suomi ....................................................................................... 29 Magyar ...................................................................................... 31 Srpski........................................................................................ 33
1
Step 1: Unpack the Unit
This package contains the following items: The unit, Quick Start Guide, screws for disk drives, key, power cord,
warranty card, CD with Install Wizard, NuClient, Backup Player and Offline License Tool application, user manual, and quick start guide.
To configure the unit, you must install the software onto a desktop/ laptop running
Windows XP-SP3 32bit, Windows 7 32/64bit, Mac OS X v10.6/10.7.
Step 2: Install Hard Drives
Refer to compatibility list and install HDDs. For optimal performance consideration, install disks with the same model and storage capacity. The available RAID level depends on the amount of disks installed.
Step 3: Connect to the Network
Enable the DHCP function within the network, as the unit will retrieve an IP address through DHCP by default.
Step 4: Connect the Power
Press the power button once connecting the power.
Step 5: Install the Software
Insert the CD into your CDROM and double-click Setup.exe to begin installation.
Step 6: Set up the Unit
The software Installation Wizard performs the setup procedures on the unit. After the procedure, you can begin using it. 1. Go to Start > NUUO Titan Series > NUUO Install Wizard. 2. This program will show the default language setting and initiation
mode. 3. Choose your preferred language and initiation mode, and then click
the button.
2
Express Mode: you dont need to set up the network and RAID level
Advanced Mode: configure all settings manually: network, license, camera, Date/Time, upgrade notification, and RAID level
4. Follow the directions of Installation Wizard and click the FINISH
button to starting initializing.
Once the FINISH button is clicked, the unit will start working. In order to ensure the
stability of the unit, never pull any disks out when the system is running.
5. After setting up the unit, log in to the system by entering its IP address in the browser (Internet Explorer 8 and later, Firefox on Windows, and Safari on Mac1).
1 Firefox on windows and Safari on Mac are supported from v1.1.0, but Safari support is limited to settings only
3
1
CDCDNu
Windows XP-SP3 32bitWindows 7
32/64bitMac OS X v10.6/10.7
2
RAID
3
DHCP IP DHCP
4
5
CD CDROMSetup.exe
6
1. windows> NUUO Titan Series> NUUO Install Wizard
2.
3.
4
RAID
/ RAID
4. Installation Wizard
5. Internet Explorer 8Windows FirefoxMac Safari2
2 Firefox on windows and Safari on Mac are supported from v1.1.0, but Safari support is limited to settings only
5
CD Install Wizard (), NuClient, Backup Player (), Verification Tool ()Offline Tool ()
Windows XP-SP3 32bitWindows 7 32/64bit
Mac OS X v10.6/10.7
(RAID)
DHCP IP
CD Setup.exe
1. > NUUO Titan Series>NUUO Install Wizard 2.
3.
6
RAID / RAID
4.
5. IE 8 Windows Firefox Mac Safari3
3 From Titan NVR v1.1.0 Firefox (Windows) Safari (Mac) Safari
7
Paso 1: Desempaquetar la Unidad
El paquete contiene los siguientes elementos:
La Unidad, Gua de Inicio Rpido, tornillos para unidades de disco, llave,
cable de alimentacin, tarjeta de garanta, CD con el Asistente para la
Instalacin, NuClient, Reproduccin y aplicacin Offline Tool y
manual de instrucciones y gua de inicio rpido.
Para configurar la unidad, debe instalar el software en una computadora de escritorio/ porttil
que ejecuta Windows XP-SP3 32bit, Windows 7 32/64bit, Mac OS X v10.6/10.7.
Paso 2: Instalacin de Discos Duros
Consulte la lista de compatibilidad e instalar HDDs. Para la consideracin de un
rendimiento ptimo, instalar con el mismo modelo de disco y la capacidad de
almacenamiento. El nivel de RAID disponible depende de la cantidad de discos
instalados.
Paso 3: Conectarse a la Red
Activar la funcin DHCP en la red, como la unidad recuperara una direccin IP
mediante DHCP por defecto.
Paso 4: Conexin a la Fuente de Alimentacin
Pulse el botn para encender una vez que se conecte la fuente de alimentacin.
Paso 5: Instalar el Software
Insertar el CD en el CD-ROM y doble clic en Setup.exe para iniciar la
instalacin.
Paso 6: Establecer la Unidad
El Asistente para la Instalacin de software lleva a cabo los procedimientos
de configuracin de la unidad. Despus del procedimiento, podr comenzar el
uso.
1. Ir a Inicio > NUUO Titan Series > NUUO Asistente para la Instalacin.
2. Este programa muestra la configuracin de idioma predeterminado y el
modo de inicio.
3. Elige el idioma preferido y el modo de inicio, luego clic el botn .
8
Modo Express: no es necesario configurar la red y el nivel de RAID
Modo Avanzado: configurar todos los ajustes manualmente: Red,
licencia, cmara, Fecha/Hora, notificacin de actualizacin y nivel de
RAID.
4. Siga las instrucciones del Asistente para la instalacin y haga clic en el botn
FINALIZAR para comenzar la inicializacin.
Una vez que haga clic al botnFINISH , la unidad comenzar a trabajar. Con el fin de
garantizar la estabilidad de la unidad, nunca extraer los discos cuando el sistema est
funicionando.
5. Despus de establecer la unidad, iniciar session en el sistema introduciendo
su direccin IP en el navegador (Internet Explorer 8 o superior, Firefox en
Windows y Safari en Mac4).
4 Firefox en Windows y Safari en MAC son soportados en NVR Titan v1.1.0, pero en Safari el soporte est limitado solamente en "configuraciones"
9
Schritt 1: Auspacken des Gertes
Die Verpackung sollte folgenden INhalt haben: Das Gert, Schnellstartanleitung, Schrauben fr die Festplatten, Schlssel,
Stromkabel, Garantiekarte und eine CD mit dem INstallationswizard,
NuClient, Wiedergabe und dem Offline Tool, Benutzerhandbuhc und
Schnellstartanleitung.
Um das Gert zu konfigurieren, muss die Software auf einem PC oder Laptop installiert warden,
welches Windows XP-SP3 32bit, Windows 7 32/64bit, Mac OS X v10.6/10.7.
Schritt 2: Festplatten installieren
Schauen Sie in die Kompatibilittsliste und installieren dann die Festplatten. Fr
eine optimlae Festplattenperformanz, installieren Sie Festplatten des gleichen
Typs und Gre. Der RAID Modus bsaiert auf der Anzahl der Festplatten.
Schritt 3: Verbinden Sie das Netzwerk
Aktivieren Sie in Ihrem Netzwerk einen DHCP Server und das Gert wird
automatisch eine IP Adresse bekommen.
Schritt 4: Verbinden Sie das Stromkabel
Drcken Sie den Power Knop, sobald das Gert mit dem Stromnetz verbunden
ist.
Schritt 5: Installieren Sie die Software
Legen Sie die CD in Ihr CD-Rom Laufwerk ein und klicken Sie die Datei
Setup.exe an, um mit der Installation zu beginnen.
Schritt 6: Richten Sie das Gert ein
Die Software Installations Wizard fr den Einrichtungprozess durch. Nach der
Prozedur knnen Sie das Gert benutzen.
1. Gehen Sie auf Start > NUUO Titan Series > NUUO Installations Wizard.
2. Dieses Programm wird die Standardsprache und Initialisierungsmodus
zeigen.
3. Whlen Sie die bevorzugte Sprache und Initialisierungsmodus aus und
klicken danach auf die Schaltflche.
10
Express Modus: Sie brauchen sich nicht um IP Adresse und RAID Level
kmmern.
Erweiterter Modus: Konfigurieren Sie alle Eisntellungen manuell:
Netzwerk, Lizenz, Kamera, Datum/Uhrzeit, Update Benachrichtigung und
RAID Level
4. Folgen Sie den Anweisungen des Installations Wizard und klicken Sie auf
FERTIGSTELLEN um die Initialisierung zu starten.
Sobald der Fertigstellen Knopf gedrckt ist, fngt das Gert an zu arbeiten. Um die
Stabilitt des System nicht zu gefhrenden, ziehen Sie niemals eine Festplatte im
laufendem Betrieb heraus.
5. Nachdem das Gert eingerichtet ist, knnen Sie sich an das Gert anmelden,
indem Sie die IP Adresse im Browser eingeben (Internet Explorer 8 and later,
Firefox on Windows, and Safari on Mac5).
5 Firefox on windows and Safari on Mac are supported from v1.1.0, but Safari support is limited to settings only
11
Etape 1: Dballage de l'Unit Ce paquet contient les lments suivants: L'unit, Guide de dmarrage rapide, vis pour les disques durs, cls,
cordon d'alimentation, carte de garantie, un CD avec l'assistant d'installation, NuClient, relecture et outil d'application hors ligne, mode d'emploi, et guide de dmarrage rapide
Pour configure L'unit, vous devez installer le logiciel sur un ordinateur de bureau / ordinateur
portable en cours d'excution Windows XP-SP3 32bit, Windows 7 32/64bit, Mac OS X
v10.6/10.7.
tape 2: Installation des disques durs
Reportez-vous la liste de compatibilit et d'installer les disques durs. Pour l'examen des performances optimales, installez des disques avec le mme modle et capacit de stockage. Le niveau RAID disponible dpend de la quantit de disques installs.
tape 3: Connexion au rseau Activer la fonction DHCP au sein du rseau, que l'unit permettra de rcuprer une adresse IP par DHCP par dfaut.
Etape 4: Connecter la Puissance Appuyez sur le bouton d'alimentation une fois la mise sous tension.
tape 5: Installation du logiciel Insrez le CD dans votre lecteur de CDROM et double-cliquez sur Setup.exe pour commencer l'installation.
tape 6: Mettre en place l'Unit L'installation du logiciel Assistant effectue les procdures de configuration sur l'appareil. Aprs la procdure, vous pouvez commencer l'utiliser. 1. Cliquez sur Dmarrer NUUO Titan Series> NUUO Assistant
d'installation. 2. Ce programme affiche le paramtre de langue par dfaut et le mode
initiation. 3. Choisissez votre langue prfre et le mode initiation, puis cliquez sur
le bouton
12
Express Mode: vous n'avez pas besoin de mettre en place le rseau et le niveau de RAID.
Mode avanc: configurer tous les paramtres manuellement: rseau, camra, date / heure, la notification de mise niveau, et le niveau RAID
4. Suivez les instructions de l'assistant d'installation et cliquez sur le
bouton Terminer pour commencer l'initialisation
Une fois le bouton Terminer est cliqu, l'appareil commencera fonctionner. Afin
d'assurer la stabilit de l'appareil, ne retirez jamais tous les disques quand le systme
est en marche
5. Aprs la mise en place de l'unit, connectez-vous au systme en
saisissant l adresse IP dans le navigateur (Internet Explorer 8 and later, Firefox on Windows, and Safari on Mac6).
6 Firefox on windows and Safari on Mac are supported from v1.1.0, but Safari support is limited to settings only
13
Step 1: Disimballare il dispositivo
Questa confezione contiene:
LUnit, Guida Rapida allInstallazione, Manuale Utente, viti per fissare gli
Hard disk, chiave, cavo dalimentazione, cedolino di garanzia, CD con
Installation Wizard, NuClient, Visualizzatore Archivi e Strumento di
Attivazione Offline.
Per configurare lunit si deve installare il software su un desktop/ laptop con Windows
XP-SP3 32bit, Windows 7 32/64bit, Mac OS X v10.6/10.7.
Step 2: Installazione Hard Disks
Fate riferimento alla lista di compatibilit ed installate gli Hard Disks. Per
prestazioni ottimali, installate dischi dello stesso modello e capacit. I livelli
RAID disponibili dipendono dal numero di sischi installati.
Step 3: Collegarsi alla rete
Abilitate la funzione DHCP sulla rete, poich per default lunita prender
automaticamente lindirizzo da un server DHCP.
Step 4: Collegare lalimentazione
Premere il tasto Power dopo aver collegato lalimentazione.
Step 5: Installare il Software
Inserite il CD nel vostro CDROM e fare doppio click su Setup.exe per iniziare
linstallazione.
Step 6: Impostare lUnit
Il software Installation Wizard effettua le procedure di configurazione
dellUnit.
Al termine potete iniziare ad utilizzare il sistema.
1. Vai ad Avvio > NUUO Titan Series > NUUO Install Wizard.
2. Questo programma mostrer limpostazione di default della lingua e la
modalit di inizializzazione.
3. Scegliere la lingua preferita e la modalit di inizializzazione, e fare click sul
14
tasto .
Express Mode: non occorre specificare impostazioni di rete e livello RAID
Advanced Mode: specificare tutte le impostazioni manualmente: rete,
licenze, Data/Ora, telecamere, notifiche aggiornamenti e livello RAID
4. Seguire le indicazioni di Installation Wizard e fare click sul tasto
TERMINA per avviare linizializzazione.
Una volta che il tasto TERMINA stato premuto lunit inizier a funzionare. Per
assicurare la stabilit del sistema non rimuovere alcun disco mentre il sistema in
funzione.
5. Dopo linizializzazione, accedere al sistema inserendone lindirizzo IP nella
barra degli indirizzi del browser (Internet Explorer 8 e successivi, Firefox su
Windows, e Safari su Mac7).
7 Firefox su Windows e Safari su MAC sono supportati nel Titan NVR v1.1.0, ma il supporto Safari limitato alle sole Impostazioni
15
1: :
, ,
, , , , CD
Installation Wizard ( ), NuClient,
Backup Player () Offline Tool (
),
/, Windows XP-SP3 32bit,
Windows 7 32/64bit, Mac OS X v10.6/10.7.
2: .
. RAID
.
3: DHCP (
), .. IP-
DHCP.
4: .
5: CD
Setup.exe .
6:
Installation Wizard.
.
1. Start > NUUO
Titan Series > NUUO Install Wizard.
2.
.
3.
.
16
Express Mode:
RAID
Advanced Mode: : ,
, , /,
RAID
4. Installation Wizard
FINISH .
FINISH .
.
5. ,
IP- (Internet Explorer 8 and later,
Firefox on Windows, and Safari on Mac8).
8 Firefox on windows and Safari on Mac are supported from v1.1.0, but Safari support is limited to settings only
17
Krok 1: Rozbalte balen
Balen obsahuje nsledujc: MiniNVR zazen, roubky pro harddisky, kl, sov kabel, zrun
list, CD s Installation Wizard, NuClient, Backup Player a Offline Tool application, uivatelsk manual a rychl prvodce.
Pro konfiguraci zazen muste nainstalovat software na pota s operanm
systmem Windows XP-SP3 32bit, Windows 7 32/64bit nebo Mac OS X v10.6/10.7.
Krok 2: Instalace harddisk
Zkontrolujte podporu harddisk a nainstalujte je. Pro optimln vkon instalujte harddisky stejnho modelu a velikosti. Nastaviteln rove RAID je zvisl na potu harddisk v zazen.
Krok 3: Pipojen k si
Povolte funkci DHCP, aby zazen zskalo IP adresu automaticky.
Krok 4: Pipojen napjen
Po pipojen k si zazen zapnte.
Krok 5: Instalace softwaru
Vlote CD do mechaniky a dvojklikem na Setup.exe spuste instalaci.
Krok 6: Nastaven zazen
Software Installation Wizard provd zkladn nastaven. Po tto inicializaci mete zazen zat pouvat. 1. Start > NUUO Titan Series > NUUO Install Wizard. 2. Program zobraz defaultn nastaven jazyka a reim inicializace. 3. Vyberte preferovan jazyk a reim inicializace, pot kliknte na
tlatko
18
Express Mode: nemuste provdt sov nastaven, nastaven
datumu a asu a nastaven RAID rovn Advanced Mode: vechna nastaven se provd run: sov
nastaven, licence, nastaven kamer, nastaven datumu a asu, nsataven automatickho upozorovn na aktualizace, nastaven RAID rovn
4. Nsledujte pokyny Installation Wizard a kliknte na FINISH pro
zatek inicializace zazen.
Po kliknut na tlatko FINISH se zane zazen inicializovat. V rmci stability
systmu nikdy nevytahujte harddisky, kdy je systm sputn.
5. Po nastaven zazen se pihlate do systmu zadnm IP adresy do prohlee (Internet Explorer 8 and later, Firefox on Windows, and Safari on Mac9).
9 Firefox on windows and Safari on Mac are supported from v1.1.0, but Safari support is limited to settings only
19
Step 1:
:
NUUO NVRTitan, , , , ,
, CD( S/W : , SW,
, , )
NUUO NVRTitan Window XP-SP3 32bit, Window7 32/64bit, Mac OS X v10.6/10.7 CD S/W .
Step 2:
.
, .
RAID level .
Step 3:
DHCP NUUO Titan NVR IP
.
Step 4:
Titan NVR .
Step 5:
NUUO CD
Setup.exe .
Step 6: NVRTitan
CD Installation Wizard
. .
1. > NUUO Titan Series > NUUO Install Wizard.
2. .
3. .
20
1. Install Wizard
: , RAID
. ( .)
: . (,
, , /, , RAID ) ()
4. Installation Wizard FINISH
.
FINISH , . HDD , .
5. , IP
. ID/PW .
( OS 8 , Firefox Mac Safari10
)
2.
10 OS Firefox MAC Safari Titan NVR v1.1.0 . , Safari .
21
Krok 1: Otwieranie opakowania
Opakowanie zawiera: Rejestrator, Poradnik Szybki Start, rubki do przymocowania
dyskw, klucz, przewd zasilajcy, kart gwarancyjn, CD z oprogramowaniem, instrukcja uytkownika.
Aby skonfigurowa jednostk naley zainstalowa oprogramowanie na komputerze
pracujcym pod kontrol systemu Windows XP-SP3 32bit, Windows 7 32/64bit, Mac
OS X v10.6/10.7.
Krok 2: Instalacja dyskw twardych
Zainstaluj dyski twarde zgodne z list referencyjn. Aby zachowa optymaln prac urzdzenia naley instalowa dyski o tym samym modelu oraz pojemnoci. Dostpny tryb RAID zaley od iloci zainstalowanych dyskw.
Krok 3: Podczanie do sieci
Po podczeniu rejestratora do sieci z serwerem DHCP rejestrator automatycznie pobierze ustawienia sieciowe.
Krok 4: Wczanie zasilania.
Po podczeniu przewodu zasilania wcinij przycisk zasilania.
Krok 5: Instalacja oprogramowania
Umie pyt CD w napdzie, a nastpnie dwukrotnie kliknij Setup.exe, aby rozpocz process instalacji.
Krok 6: Konfiguracja rejestratora
Oprogramowanie Installation Wizard przeprowadzi uytkownika przez process konfiguracji uytkownika. 1. Nacinij Start > NUUO Titan Series > NUUO Install Wizard. 2. Pojawi si okno z wyborem jzyka oraz trybu inicjacji. 3. Wybierz preferowany jzyk oraz tryb inicjacji, a nastpnie kliknij
przycisk .
22
Tryb Ekspresowy: nie jest wymagana konfiguracja ustawie
sieciowych, daty i czasu oraz trybu RAID Tryb Zaawansowany: rczna konfiguracja wszystkich ustawie:
sie, licencja, kamera, data/czas, powiadamianie o dostpnych aktualizacjach, tryb RAID
4. Postpuj zgodnie ze wskazwkami programu Installation Wizard, a
nastpnie kliknij przycisk ZAKOCZ.
Po klikniciu przycisku ZAKOCZ, rejestrator zostanie zainicjalizowany. Aby
unikn niestabilnoci pracy rejestratora NIGDY nie wyjmuj dyskw podczas jego
pracy.
5. Po skonfigurowaniu rejestratora moesz zalogowa si do rejestratora poprzez wpisanie jego adresu IP w przegldarce (Internet Explorer 8 and later, Firefox on Windows, and Safari on Mac11).
11 Firefox on windows and Safari on Mac are supported from v1.1.0, but Safari support is
limited to settings only
23
Stap 1: het toestel uitpakken
De verpakking bevat de volgende items: Het toestel, Verkorte handleiding, schroeven voor de diskdrives,
stroomkabel, garantie kaart, cd met Installatiewizard, NuClient, Afspelen en de toepassing Offline Tool, gebruikershandleiding en verkorte handleiding
Configureer het toestel door de software op een pc/laptop met Windows XP-SP3 32bit,
Windows 7 32/64bit, Mac OS X v10.6/10.7 te installeren.
Stap 2: harde schijven installeren
Zie de compatibiliteitslijst en installeer de harde schijven. Voor optimale prestaties installeert u disks van hetzelfde model en opslagcapaciteit. Welk RAID-niveau beschikbaar is, is afhankelijk van het aantal genstalleerde disks.
Stap 3: verbinding maken met het netwerk
Schakel de DHCP-functie van het netwerk in, aangezien het toestel een ip-adres ophaalt via DHCP.
Stap 4: stroom aansluiten
Druk eenmaal op de aan/uitknop om het toestel aan te zetten.
Stap 5: software installeren
Plaats de cd in het cd-romstation en dubbelklik op Setup.exe om de installatie te starten.
Stap 6: het toestel instellen
De Installatiewizard voert de installatieprocedures in op het toestel. Hierna kunt u het toestel gebruiken. 1. Ga naar Start > NUUO Titan Series > NUUO Installatiewizard. 2. Dit programma toont de standaardinstellingen voor taal en
initiatiemodus.
24
3. Kies de gewenste taal en initiatiemodus en klik vervolgens op de knop
.
Snelle modus: u hoeft niet zelf het netwerk en RAID-niveau in te stellen.
Geavanceerde modus: configureer alle instellingen zelf: netwerk, camera, datum/tijd, upgrademelding en RAID-niveau
4. Volg de instructies van Installatiewizard en klik op VOLTOOIEN om
het initialiseren te starten.
Zodra u op VOLTOOIEN klikt, is het toestel functioneel. Om de stabiliteit van het
toestel te waarborgen, mag u nooit disks lostrekken als het systeem geactiveerd is.
5. Zodra het toestel is ingesteld, meldt u zich aan bij het systeem door het ip-adres in te voeren in de browser (Internet Explorer 8 and later, Firefox on Windows, and Safari on Mac12).
12 Firefox on windows and Safari on Mac are supported from v1.1.0, but Safari support is limited to settings only
25
Steg 1: Packa upp enheten
Detta paket innehller fljande: Enhet, snabbstartsguide, skruvar fr hrddiskar, nyckel, ntkabel,
garantikort, CD med applikationerna Installationsguide, NuKlient, Uppspelning och Offlineverktyg, anvndarmanual och snabbstartsguide.
Om du vill konfigurera enheten mste du installera programvaran p en
statior/brbar dator med Windows XP-SP3 32bit, Windows 7 32/64bit eller Mac OS X
v10.6/10.7.
Steg 2: Installera hrddiskar
Se kompabilitetslistan och installera hrddiskarna . Fr optimal prestanda installera diskar med samma modell och lagringskapacitet. Den tillgngliga RAID nivn beror p antalet installerade diskar.
Steg 3: Anslut till ntverket
Aktivera DHCP-funktionen inom ntverket, eftersom enheten kommer att hmta IP-adress via DHCP per default.
Steg 4: Anslut strmmen
Tryck p strmbrytaren en gng fr att koppla p strmmen.
Steg 5: Installera mjukvaran
Stt in CD:n i CDROM enheten och dubbelklicka p Setup.exe fr att pbrja installationen.
Steg 6: Instllning av enhet
Mjukvarans Installationsguide utfr instllningarna p enheten. Efter denna procedur kan du brja anvnda den. 1. G till Start > NUUO Titan Series > NUUO Installations guide. 2. Detta program visar den frvalda sprkinstllningen och
initieringslge.
3. Vlj nskat sprk och initieringslge och klicka sedan knappen.
26
Express lge: du behver inte stlla in ntverk och RAID niv Avancerat lge: konfigurera alla instllningarna manuellt: ntverk,
licens, kamera, Datum/Tid, uppgraderings notofiering och RAID niv
4. Flj anvisningarna i installationsguiden och klicka p knappen
FINISH (slutfr) fr att starta initieringen.
Nr FINISH (slutfr) knappen r tryckt, kommer enheten att brja arbeta. Fr att
skerstlla stabiliteten i enheten, dra aldrig ut ngra hrddiskar nr systemet r
igng.
5. Efter instllning av enheten, logga in i systemet genom att ange dess
IP-adress i webblsaren (Internet Explorer 8 och senare, Firefox med Windows, och Safari med Mac13).
13 Firefox med Windows och Safari med Mac har std i Titan NVR v1.1.0, men Safari stdet r begrnsat till endast instllningar
27
Passo 1: Desempacote o Equipamento Esta embalagem contm os seguintes itens:
O Equipamento, Guia Rpido de Inicializao, parafusos para fixao dos
Discos Rgidos, chave, carto de garantia, cabo de alimentao, CD com
Assistente de Instalao, NuCliente, Playback, Aplicativo de
Ferramenta Offline, Manual de Usuro e Guia Rpido de Inicializao.
Para configurar a unidade, voc precisa instalar o software em um desktop ou
notebook equipado com Windows XP SP3, Windows 7 32 ou 64 bits ou Mac OS X
v10.6/10.7.
Passo 2: Instalar os Discos Rgidos Verifique a lista de compatibilidade de HDs para selecionar um modelo
apropriado. Para melhor performance, sempre instalar discos idnticos: mesmo
modelo e maeca e de mesma capacidade de armazenamento. O nvel de RAID
disponvel depende diretamente do nmero de discos instalados.
Passo 3: Conectar-se Rede
Habilitar a funo DHCP dentro da rede, para que a unidade adquira
automaticamente um endereo IP atravs do mesmo, por padro.
Passo 4: Conectar-se Energia Aps verificar a tenso da rede de energia, conectar o cabo de energia e a fonte
e pressionar o boto Power para ligar a unidade.
Passo 5: Instalar o Software
Insira o CD em seu CDROM e clique duas vezes o aplicativo Setup.exe, para
comear a instalao.
Passo 6: Configure a Unidade O software Installation Wizard (Assistente de Instalao) executar os
procedimentos de setup da unidade. Aps estes procedimentos, voc poder
comear a utilizar o equipamento.
1. V para Iniciar > NUUO Titan Series > NUUO Install Wizard (Assistente de
Instalao).
2. Este programa ir exibir o idioma padro e modo de inicializao.
3. Selecione o idioma de sua preferncia e o modo de inicializao, ento clique
no boto .
28
Express Mode (Modo Expresso): no se faz necessrio a configurao
de parmetros de rede e nvel de RAID.
Advanced Mode (Modo Avanado): configurao de todos os
parmetros manualmente: rede, licena, cameras, data e hora,
notificao de upgrade/atualizao e nvel de RAID.
4. Siga as instrues do Installation Wizard (Assistente de Instalao) e
clique em FINISH (Finalizar) para inicializar a instalao.
Uma vez pressionado o boto FINISH (Finalizar), a unidade comear a trabalhar.
Para assegurar a estabilidade da unidade, nunca retire os discos rgidos enquanto o
equipamento estiver ligado.
5. Aps a configurao do equipamento, faa login no mesmo atravs do seu
endereo IP, utilizando um navegador web (Internet Explorer 8 ou superior,
Firefox no Windows e Safari no Mac14).
14 Firefox no Windows e Safari no Mac so suportados pelo Titan NVR v1.1.0, entretanto, no Safari o suporte est limitado apenas "configuraes"
29
Vaihe 1: Ota laite pakkauksesta
Pakkauksessa on seuraavat osat: Laite, pikaopas, asemien kiinnitysruuvit, avain, virtajohto,
takuukortti, CD, jossa on asennusohjelman, NuClient, toiston, ja Offline Tool sovellukset, kyttohje ja pikaopas
Mrittksesi laitteen asetukset sinun on asennettava ohjelmisto
pyttietokoneeseen/ kannettavaan tietokoneeseen, jonka kyttjrjestelmn on
Windows XP-SP3 32bit, Windows 7 32/64bit tai Mac OS X v10.6/10.7.
Vaihe 2: Asenna kiintolevyt
Tarkista yhteensopivien tuotteiden luettelo ja asenna kiintolevyt. Varmista paras mahdollinen suorituskyky asentamalla samanmalliset levyt, joilla on yht paljon tallennustilaa. Saatavilla oleva RAID-taso riippuu asennettujen levyjen lukumrst.
Vaihe 3: Yhdist verkkoon
Ota verkon automaattinen asetus (DHCP) kyttn, jolloin laite hakee IP-osoitteen oletusasetuksena DHCP:n kautta.
Vaihe 4: Kytke verkkovirtaan
Kytke virta plle painamalla virtapainiketta yhden kerran.
Vaihe 5: Asenna ohjelmisto
Laita CD CDROM-asemaan ja kaksoisnapsauta Setup.exe aloittaaksesi asennuksen.
Vaihe 6: Mrit laitteen asetukset
Asennusapuohjelma suorittaa laitteen asennuksen. Kun laitteen asennus on suoritettu loppuun, se voidaan ottaa kyttn. 1. Mene kohtaan Kynnist > NUUO Titan Series > NUUO
asennusohjelma. 2. Ohjelma tuo esille oletuskielen asetukset ja alustustilan.
3. Valitse haluamasi kieli ja alustustila ja napsauta sitten -painiketta.
30
Pikatila: sinun ei tarvitse asettaa verkkoa ja RAID-tasoa. Edistynyt tila: mrit kaikki asetukset manuaalisesti: verkko,
kamera, pivmr/kellonaika, pivitysilmoitukset ja RAID-taso.
4. Seuraa Asennusapuohjelman ohjeita ja napsauta SUORITA LOPPUUN-painiketta kynnistksesi alustuksen.
Laite kynnistyy, kun "SUORITA LOPPUUN"-painiketta on napsautettu. Varmista
laitteen kunnollinen toiminta pitmll huolta siit, ett et koskaan poista levyj
laitteesta, kun jrjestelm on kynniss.
5. Sen jlkeen, kun laitteen asetukset on mritetty, kirjaudu sisn
jrjestelmn antamalla sen IP-osoite selaimeen (Internet Explorer 8 and later, Firefox on Windows, and Safari on Mac15).
15 Firefox on windows and Safari on Mac are supported from V1.1.0, but Safari support is
limited to settings only
31
Els lps: A rgzt kicsomagolsa
Ez a csomag az albbi elemeket tartalmazza: Az eszkz, Teleptsi tmutat, merevlemezrgzt csavarok, kulcs,
tpkbel, jtllsi jegy, CD, melyen Teleptsi varzsl, NuClient, Visszajtszs s Kapcsolat nlkli eszkz szoftverek, Hasznlati utasts s Teleptsi tmutat tallhat
Az eszkz belltshoz egy Windows XP-SP3 32bit, Windows 7 32/64bit, Mac OS X
v10.6/10.7 opercis rendszer szmtgpre kell telepteni a szoftvereket.
Msodik lps: Merevlemezek behelyezse
Ellenrizd a kompatibilitsi listt lemezvlaszts eltt. Csavarozd be a merevlemezeket. Optimlis mkdshez tancsos egyforma (ugyanaza a gyrt ugyanakkora kapacits) lemezeket hasznlni. A vlaszthat RAID mdok a behelyezett lemezek szmtl fggenek.
Harmadik lps: Csatlakoztasd a hlzatot
Legyen a hlzatban egy DHCP szerver (rendszerint egy router), amitl alaprtelmezetten az eszkz IP-cmet kap.
Negyedik lps: Csatlakoztasd a tpllst
Majd nyomd meg a bekapcsolgombot.
tdik lps: Teleptsd a szoftvert Helyezd be a teleptlemezt s amennyiben nem indul el magtl, indtsd el a Setup.exe-t a telepts kezdshez.
Hatodik lps: Az eszkz belltsa
A Teleptsi varzsl elvgzi az eszkz belltst, ami utn a rgzt hasznlhat. 1. Start > NUUO Titan Series > NUUO Install Wizard programot indtod. 2. Itt kivlaszthatod az alaprtelmezett nyelvet s a belltsi mdot.
3. Vlassz nyelvet s mdot, majd kattints a gombra.
32
Expressz Md: nem krdez r a hlzat, a pontosid s a RAID belltsaire.
Fejlett Md: minden belltsra rkrdez: hlzat, licensz, kamerk, Dtum/Id, frisstsi rtest s RAID md.
4. Kvesd a Teleptsi varzsl utastsait s kattints a BEFEJEZS
gombra az inicializls megkezdshez.
A BEFEJEZS-re kattints utn az eszkz dolgozni kezd. A rendszer stabilitsa
rdekben soha ne hzz ki merevlemezt bekapcsolt gpbl.
5. Az eszkz belltsa utn jelentkezz be a kszlkbe, gy hogy az IP cmt berod a webbngsz cmsorba. (Internet Explorer 8 and later, Firefox on Windows, and Safari on Mac16).
16 Firefox on windows and Safari on Mac are supported from v1.1.0, but Safari support is limited to settings only
33
Korak 1: Raspakivanje ureaja
Paket se sastoji od sledeih delova: Ureaj, kratko uputstvo, arafi za diskove, klju, napojni kabl,
garantni list, CD sa Instalacionim arobnjakom (Installation Wizard), NuKlijentom (NuClient), Backup Player i Offline alatkom (Offline Tool) aplikacijama, korisnikim uputstvom i kratkim uputstvom
Za konfigurisanje ureaja, morate imati instaliran softver na vaem raunaru/ laptopu
na kom je instaliran Windows XP-SP3 32bit, Windows 7 32/64bit, Mac OS X
v10.6/10.7.
Korak 2: Instalacija hard diskova
Proverite listu kompatibilnih diskova i instalirajte HDD. Za optimalne performanse, instalirajte diskove istog modela i kapapaciteta. Dostupni RAID nivoi zavise od broja instaliranih diskova.
Korak 3: Konekcija na mreu
Omoguite DHCP funkciju na mrei, poto e ureaj dobiti IP adresu kroz DHCP.
Korak 4: Prikljuivanje napajanja
Pritisnite power dugme nakon to ste prikljuili napajanje.
Korak 5: Instalacija softvera
Ubacite CD u va CDROM i dvaput kliknite na Setup.exe kako bi poeli proces instalacije.
Korak 6: Podeavanje ureaja
Program Installation Wizard izvrava procedure podeavanja ureaja. Nakon zavrene procedure, moete poeti sa koritenjem ureaja. 1. Idite na Start > NUUO Titan Series > NUUO Install Wizard. 2. Program e prikazati podrazumevani jezik i nain inicijalizacije. 3. Odaberite va eljeni jezik i nain inicijalizacije, i nakon toga klikite na
dugme.
34
Expresni nain: ne morate podeavati mreu i RAID nivo Napredni nain: konfiguriite sva podeavanja runo: mreu,
licence, kamere, Datum/Vreme, obavest o nadogradnji, RAID nivo
4. Pratite uputstva Installation Wizard i kliknite na FINISH dugme za pokretanje inicijalizacije.
Nakon to ste kliknuli na FINISH dugme, ureaj poinje sa radom. Kako bi osigurali
stabilnost ureaja, nikad ne izvlaite diskove dok sistem radi.
5. Nakon podeavanja ureaja, prijavite se na sistem upisivanjem njegove IP adrese u browser (Internet Explorer 8 and later, Firefox on Windows, and Safari on Mac17).
17 Firefox on windows and Safari on Mac are supported from v1.1.0, but Safari support is limited to settings only
Add: C Block, 18 Sihyuan St. Jhongjheng District, Taiwan (ROC) TEL: +886-2-2362-2260
E-mail: [email protected]