Upload
charzree
View
217
Download
0
Embed Size (px)
DESCRIPTION
Bolts, Nuts, & Gaskets
Citation preview
三木 悟2013.01.19 maksgym
Trivia about Bolts, Nuts & Gaskets (BNPK の 豆 知 識 )
No. Description
1 ドブ漬け亜鉛メッキのボルト・ナットの場合、ナットと対になっていないボルトは相手がタップ穴の場合になるので、ドブ漬け亜鉛メッキ処理後にネジ部の加工が必要となる。
Hot Dipped Galvanized Bolt and Nut (1)
1. As to the hot dipped galvanized bolt and nut
which are supplied as one pair, there is no
need of the additional machining for thread,
because the manufacturer supplies bolt and
nut after connecting them.
2. However, if considering the case that only
the dipped galvanized bolts are supplied, it
means that those bolts are used for the
tapped holes. Therefore, the additional
machining will be required after galvanizing
in this case.
2 ドブ漬け亜鉛メッキのボルト・ナットの場合は、ナットをドブ漬け亜鉛メッキ用のナットがあり、勘合時に問題が出ないように大きめのネジ寸法となっている。
Hot Dipped Galvanized Bolt and Nut (2)
In case of the hot dipped galvanized bolt and nut,
the nut which has larger dimension of thread is
used so that the hot dipped galvanized bolt and
nut can be connected without problem.
3 6角ボルト材料は、サイズが大きくなると長さが10mm単位でしかない。それ以外の寸法は特殊となる。頭なしのずん切りボルトは関係なし
Standard Length of Hexagon Bolt
As to the hexagon bolt, the standard length** of
bolt is as follows:
1) Length up to 100mm : 10mm, 15mm,20mm ...90mm, 95mm, 100mm
2) Length over 100mm: 110mm, 120mm, 130mm, 140mm ......
In case of the threaded rod, there is not the
standard length as abovementioned.
(Note)
standard length**: The bolt length which is
available as commercial product.
4 新日鐵仕様の基礎ボルト(異形棒鋼タイプ)とケミカルアンカーセット(ケミカルアンカーRタイプ(日本デコラックス製;武田産業取扱)+全ネジボルト(先端斜めカット)・ナット・ワッシャー)の価格は、ほぼ同じである。
Foundation Bolt specified by Nippon Steel
Corporation versus Chemical Anchor Set
(a) Foundation Bolt specified by NSC
: Deformed Steel Bar + nut & washer
(b) Chemical Anchor Set
: Chemical Anchor R type + Thread Rod (one
【豆知識】ボルト、ナット&ガスケット Trivia about Bolts, Nuts & Gaskets.doc 1
新日鐵仕様基礎ボルト(M16× 400L);約650円/1本ケミカルアンカーセット(M16×
250L);約700円/1セット
side end is cut diagonally) + nut & washer
The price of two types in the above are almost
same as follows:
1. Foundation Bolt specified by NSC:
: M16 x 400L, about 650 yen/one set
2. Chemical Anchor Set
: M16 x 250L, about 700 yen/one set
5 リングガスケットの外径(D)と内径(d)
リングガスケットの外径(D)は、フランジボルトのPCDからボルトサイズ分を差し引いた寸法となるリングガスケットの内径(d)は、フランジボルトがフランジボルト穴の一番外側に取り付いた状態でも配管内にガスケットがはみ出ない寸法となる
Outside Dia. (D) and Inside Dia. (d) of Ring
Gasket
1.Outside Dia. (D) of Ring Gasket
D = “PCD of Flange” - “Size of Flange Bolt”
2. Inside Dia. (d) of Ring Gasket
Inside Dia. (d) is to be the dimension which the
inner side of the ring gasket does not stick out
to inside of the pipe at the condition when the
flange bolt contacts with the bottom of the bolt
hole of the flange.
6 製作納期についてM24以下は、特殊ボルトでない限り納期約1週間(材料在庫)M27以上は、材料の在庫もない状態と考えられるので一からの製作となる。納期は約3週間~1ヶ月を考えておくこと
Delivery Time
1. Bolt smaller than M24
Delivery time is about one week if the bolt is
not special specification (Because, bolts are
stocked.)
2. Bolt larger than M27
Deliver time is considered to be about three
weeks to one month because the required
bolt will be manufactured newly.
7 ボルト締付トルクボルトの締付トルクを上げる場合(緩み防止)の方法として、材質変更がある。・SS400 → SCM435*注意事項として、ナット(タップ穴)側の材質についても注意が必要で、SS材では問題とならないが、FC材の時は母材損傷の可能性あり。
Tightening Torque of Bolt
The tightening torque of bolt can be increased by
changing the material of the bolt:
For example:
SS400 → SCM435
(Note)
In this case, pay attention to the material of nut
and the base metal for tapped hole.
In case that the base metal for tapped hole is FC,
there is a possibility that the base metal will be
damage due to the strength difference of
materials between bolt and nut.
【豆知識】ボルト、ナット&ガスケット Trivia about Bolts, Nuts & Gaskets.doc 2