User's Manual

0

Content

Chapter 1 DVB-S Introduction ……………..…………………………1

1.1 Features ………………………………………………………1

1.2 System Requirements…………….……………………………1

1.3 Product listing…………………………………………………1

Chapter 2 Installation ……..……………………………………………2

2.1 Hardware Installation …………………………………………2

2.2 Software Installation ……………… ………… ………………2

2.2.1 Driver installation ……………………………………………2

2.2.2 Application installation………………….…………..……….5

Chapter 3 Run The Software………………………..……………………7

Appendix1……………………………………………..…………………10

Appendix2……………………………………………..…………………12

DVB-S TV USER’S MANUAL

1

Chapter 1 DVB-S Introduction

1.1 Features Fully compliant with DVB-DATA ETSI/EN 301 192 standard Fully compliant with supports DVB-S Protocol (EN 300 744)/MPEG-2 Support USB 2.0 Hi-Speed Input frequency: 950 MHz ~ 2150 MHz Symbol rate: 2 ~ 45 MS/s Compatible with the C/Ku MCPS/SCPC Multi-satellite receive control DiSEqC2.0/22KHZ LNB Power Supply: 14/18V <400mA Special low-door design Support Infrared Remote Control Support Windows Vista32 Support real-time Digital Video Recording (DVR) and time shift function Support digital Teletext and IP data function Still image snapshot and save to BMP file Support popular third party software ProgDVB

1.2 System Requirements Pentium III 667MHz or higher 128MBytes memory or more 32MBytes display memory or more Hard Disk free space of 500MBytes or more OS supported:Windows2000 for SP4/WindowsXP for SP2 1.3 Product listing

DVB-S TV BOX 1pcs DVB-S TV BOX Manual 1pcs CD 1pcs USB Cable 1pcs Remote controller 1pcs Power Adapter 1pcs


2

Chapter 2 Installation 2.1 Hardware Installation Step1: Connect the USB port of PC and DVB-S TV BOX with USB cable Step2: Connect satellite signal to DVB-S TV BOX Step3: Connect power socket

2.2 Software Installation Before installing the software, please make sure that the product is actually installed 2.2.1 Driver installation After connecting the device, Windows will find New Hardware.


3

Choose “No, not this time”, and press “Next”.

Choose “Install from a first or specific location (Advanced)”, and Press “Next”.

Path: “CD-ROM: \Driver” and press “OK”.

Click “Next”.


4

Press “Continue Anyway”.

Press “Finish”.


5

2.2.2 Application installation

Open CD-ROM , double click icon. Click “OK”.

Click “NEXT”.

Use default path for destination folder, click “NEXT”.

Click “NEXT”.


6

Select “Full”, click “Install”

Press “Finish” to finish the setup.


7

3. Run the Software After finished the software installation, double click the “ProgDVB” icon to open the software. Click “Settings” to select “Device list”.

Select “Advanced USB2.0 DVB-S TV BOX” device, and click “Start”, “OK” to close this dialog box.

Click “Setting” to select “DiSEqC”.


8

If you have no DiSEqC, please select “None” and Click “Add LNB”

Select your LNB type and fill in LNB parameter, and choose the satellite. Then click “OK” to close the dialog box.

Click “Channel list” and select “Channel search” to choose the satellite.


9

It begins to scan.

It will take a few minutes. After the scanning, click “OK”. Then you can watch the programs.


10

Appendix 1 IPData setup

If you need to receive IP data from the satellite, please install “IP Data” software. The procedure is as follows:

Begin to setup click“Next” click“Next” click“Next” click“Install” click“Continue Anyway” click“Finish”


11


12

Appendix 2 Remote Control Unit

1 (POWER）: Press to turn off the computer 2 (MUTE）: Press to suspend sound temporarily 3 (FULL SCREEN): Press to magnify the video from the current program 4,8 (CH): Press to adjust the channel 5,7 (VOL): Press to adjust the volume 6 (ENT): Press to confirm the operation or show the program list 9 (STOP): Press to stop recording or playing 10 (CAPTURE): Press to capture one still picture and add to the capture window 11 (RECORD): Press to start recording the video 12 (SOURCE): Press to switch between playing and recording file mode 13 (RECALL): Switch back to previous channel

Documents

User's Manual